* Add missing initialization of hwif->autodma and drive->autodma to
pmac_ide_setup_dma().
* Use ide_tune_dma() in pmac_ide_dma_check().
While at it:
* Fix pmac_ide_dma_check() return value if DMA mode is not programmed
(should be "-1" otherwise ide_set_dma() will try to enable DMA).
* Remove unnecessary drive->using_dma fiddling (->dma_off_quietly is always
called before ide_set_dma() call and ide_set_dma() calls ->ide_dma_on if
->ide_dma_check returns "0").
v2:
* No reason to blacklist all ide_floppy devices and the old code was always
enabling DMA anyway (without even programming controller/device if the
device was ide_floppy).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ide_config_drive_speed() instead of pmac_ide_do_setfeature() and remove
the latter, also ide-iops.c::__ide_wait_stat() could be static again.
Since for IDE PMAC host driver IDE_CONTROL_REG is always true, device's
->quirk_list is always zero and ->ide_dma_host_{on,off} are nops than
the only changes in behavior are:
* if PIO mode is set then ->dma_off_queitly is called to disable DMA
* if setting transfer mode fails ide_dump_status() is called to dump status
v2:
* IDE PMAC controllers allow separate PIO and DMA timings and PPC userland
depends on this fact, and calls "hdparm -p" without calling "hdparm -d".
Therefore to compensate for DMA being disabled by ide_config_drive_speed()
for PIO modes:
- add IDE_HFLAG_SET_PIO_MODE_KEEP_DMA flag and set it in PMAC host driver
- add handling of the new flag to ide-io.c::do_special()
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Upper layers are responsible for controlling nIEN so don't clear nIEN after
command execution in pmac_ide_do_setfeature().
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use __ide_wait_stat() instead of wait_for_ready() in pmac_ide_do_setfeature().
While at it do following changes to match __ide_wait_stat() call in
ide_config_drive_speed():
* Wait WAIT_CMD time (20 sec) instead of 2 sec for device to clear BUSY_STAT.
* Check DRQ_STAT bit (shouldn't be set for good device status).
Also remove no longer needed wait_for_ready() from ide-iops.c.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't check for good device status before executing the command in
pmac_ide_do_setfeature() (ide_config_drive_speed() doesn't do this).
It is a job of upper layers to guarantee that the device is ready to
accept new command before we get here.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Split off checking of the status register from ide_wait_stat() to
__ide_wait_stat() helper.
* Use the new helper in ide_config_drive_speed(). The only change in the
functionality is that the function now fails if after 20 sec (WAIT_CMD)
device is still busy (BUSY_STAT bit is set) while previously instead of
failing the function continued with checking for the correct device status
(which would give the device additional 10 usec to clear BUSY_STAT bit).
* Remove stale comment for ide_config_drive_speed().
* Remove duplicate comment for ide_wait_stat() from <linux/ide.h>.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix pmac_ide_dma_check() to use pmac_ide_tune_chipset() and remove no longer
necessary pmac_ide_{m,u}dma_enable().
* While at it remove some dead code from pmac_ide_dma_check() (leftovers from
conversion to use ide_max_dma_mode()).
There should be no functionality changes caused by this patch.
v2:
* Fix compile by replacing "id" with "drive->id" in pmac_ide_dma_check()
(Noticed by Ben).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
pmac_ide_do_setfeature() contains matching nIEN setting/clearing so this
Device Control register messing in pmac_ide_dma_check() is totally unnecessary.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move adjusting of cycle time for devices providing explicit DMA cycle time
from pmac_ide_mdma_enable() to set_timings_mdma().
* Remove no longer needed drive_cycle_time argument.
* BUG() if unsupported speed argument value is passed (shouldn't happen).
* Matching access/recovery timings always exist so remove redundant check.
* Make set_timings_mdma() void.
* Update pmac_ide_tune_chipset()'s comment.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Don't check check for pmif == NULL (it should never be NULL if we got here).
* Make a local copy of the timings and set the pmif->timings[] only after
setting the transfer mode on the device (otherwise SELECT_DRIVE() call in
pmac_ide_do_setfeature() will program new timings before the transfer mode
is set on the device - this was pointed out by Sergei). This change makes
pmac_ide_tune_chipset() behavior match this of pmac_ide_{m,u}dma_enable().
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
kauai_lookup_timing() should always return non-zero return value:
* BUG() in kauai_lookup_timing() if the timing info cannot be found.
* Remove code checking for zero return value from all callers.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch removes the unused EXPORT_SYMBOL_GPL(ide_acpi_set_state)
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We need to set hwif->chipset or IDE PCI host drivers may try to claim
our ide_hwifs[] slot.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is the driver for latest Blackfin on-chip nand flash controller
- use nand_chip and mtd_info common nand driver interface
- provide both PIO and dma operation
- compiled with ezkit bf548 configuration
- use hardware 1-bit ECC
- tested with YAFFS2 and can mount YAFFS2 filesystem as rootfs
ChangeLog from try#1
- use hweight32() instead of count_bits()
- replace bf54x with bf5xx and BF54X with BF5XX
- compare against plat->page_size in 2 cases when enable hardware ECC
ChangeLog from try#2
- passed nand_test suites
- use cpu_relax() instead of busy wait loop
- some coding style issue pointed out by Andrew
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When we press ctrl-alt-del,kernel_restart_prepare will invoke
cfi_intelext_reboot which will set flash to read array mode, but later
when device_shutdown is invoked which may put current work queue to
sleep and other process may be scheduled to running and programming
flash in not FL_READY mode again. So we can't boot up if this flash is
used for bootloader.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/nand/alauda.c: In function 'alauda_bounce_read':
drivers/mtd/nand/alauda.c:412: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
In three places: summary scan, normal scan, REF_PRISTINE GC.
Just truncate at the NUL, since that was the correct thing to do in the
only case where this (inexplicable) breakage has been seen.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
In OLPC trac #4184 we found a case where a corrupted node didn't
actually get obsoleted when we tried to garbage-collect it. So we wrote
out many million copies of it, in repeated attempts to obsolete it,
until the flash became full. Don't Do That.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Instead of matching resv_blocks_gcmerge, which is only about 3, instead
match resv_blocks_gctrigger, which includes a proportion of the total
device size.
These ought to become tunable from userspace, at some point.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
If we defer updating rip until pio instructions are executed, we have a
problem with reset: a pio reset updates rip, and when the instruction
completes we skip the emulated instruction, pointing rip somewhere completely
unrelated.
Fix by updating rip when we see decode the instruction, not after emulation.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Some operand fetches are less than the machine word size and can result in
stale bits if used together with operands of different sizes.
Signed-off-by: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Implement emulation of instruction
lea r16/r32, m
opcode: 0x8d:
Signed-off-by: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
According to Intel Software Developer's Manual, Vol. 3B, Appendix H.4.2,
exit qualification should be of natural width. However, current code
uses u64 as the data type for this register, which occasionally
introduces invalid value to VMExit handling logics. This patch fixes
this bug.
I have tested Windows and Linux guest on i386 host, and they can boot
successfully with this patch.
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Before preempt notifiers, kvm needed to allocate memory with GFP_NOWAIT so
as not to have to enable preemption and take a heavyweight exit. On oom, we'd
fall back to a GFP_KERNEL allocation.
With preemption notifiers, we can do a GFP_KERNEL allocation, and perform
the heavyweight exit only if the kernel decides to put us to sleep.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch just renames the current (misnamed) _arch namings to _x86 to
ensure better readability when a real arch layer takes place.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The mutex->splinlock convertion alllows us to make some code simplifications.
As we can keep the lock longer, we don't have to release it and then
have to check if the environment has not been modified before re-taking it. We
can remove kvm->busy and kvm->memory_config_version.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
SVM gets the DB and L bits for the cs by decoding the segment. This
is in fact the completely generic code, so hoist it for kvm-lite to use.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
We don't update the vcpu control registers in various places. We
should do so.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
invlpg shouldn't fetch the "src" address, since it may not be valid,
however SVM's "solution" which neuters emulation of all group 7
instruction is horrible and breaks kvm-lite. The simplest fix is to
put a special check in for invlpg.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This was missed when moving stuff around in fbc4f2e
Fixes Solaris guests and bug #1773613
Signed-off-by: Amit Shah <amit.shah@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch enables INIT/SIPI handling using in-kernel APIC by
introducing a ->mp_state field to emulate the SMP state transition.
[avi: remove smp_processor_id() warning]
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Xin Li <xin.b.li@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Bartlomiej Zolnierkiewicz