Pull ARM updates from Russell King:
- StrongARM SA1111 updates to modernise and remove cruft
- Add StrongARM gpio drivers for board GPIOs
- Verify size of zImage is what we expect to avoid issues with
appended DTB
- nommu updates from Vladimir Murzin
- page table read-write-execute checking from Jinbum Park
- Broadcom Brahma-B15 cache updates from Florian Fainelli
- Avoid failure with kprobes test caused by inappropriately
placed kprobes
- Remove __memzero optimisation (which was incorrectly being
used directly by some drivers)
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (32 commits)
ARM: 8745/1: get rid of __memzero()
ARM: 8744/1: don't discard memblock for kexec
ARM: 8743/1: bL_switcher: add MODULE_LICENSE tag
ARM: 8742/1: Always use REFCOUNT_FULL
ARM: 8741/1: B15: fix unused label warnings
ARM: 8740/1: NOMMU: Make sure we do not hold stale data in mem[] array
ARM: 8739/1: NOMMU: Setup VBAR/Hivecs for secondaries cores
ARM: 8738/1: Disable CONFIG_DEBUG_VIRTUAL for NOMMU
ARM: 8737/1: mm: dump: add checking for writable and executable
ARM: 8736/1: mm: dump: make the page table dumping seq_file
ARM: 8735/1: mm: dump: make page table dumping reusable
ARM: sa1100/neponset: add GPIO drivers for control and modem registers
ARM: sa1100/assabet: add BCR/BSR GPIO driver
ARM: 8734/1: mm: idmap: Mark variables as ro_after_init
ARM: 8733/1: hw_breakpoint: Mark variables as __ro_after_init
ARM: 8732/1: NOMMU: Allow userspace to access background MPU region
ARM: 8727/1: MAINTAINERS: Update brcmstb entries to cover B15 code
ARM: 8728/1: B15: Register reboot notifier for KEXEC
ARM: 8730/1: B15: Add suspend/resume hooks
ARM: 8726/1: B15: Add CPU hotplug awareness
...
The new conditionally compiled code leaves some labels and one
variable unreferenced when CONFIG_HOTPLUG_CPU and CONFIG_PM_SLEEP
are disabled:
arch/arm/mm/cache-b15-rac.c: In function 'b15_rac_init':
arch/arm/mm/cache-b15-rac.c:353:1: error: label 'out_unmap' defined but not used [-Werror=unused-label]
out_unmap:
^~~~~~~~~
arch/arm/mm/cache-b15-rac.c:351:1: error: label 'out_cpu_dead' defined but not used [-Werror=unused-label]
out_cpu_dead:
^~~~~~~~~~~~
At top level:
arch/arm/mm/cache-b15-rac.c:53:12: error: 'rac_config0_reg' defined but not used [-Werror=unused-variable]
This replaces the existing #ifdef conditionals with IS_ENABLED()
checks that let the compiler figure out for itself which code to
drop.
Fixes: 55de88778f ("ARM: 8726/1: B15: Add CPU hotplug awareness")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
adjust_lowmem_bounds() called twice which can lead to stalled data
(i.e. subreg) value in mem[] array after the first call.
Zero out mem[] array before we allocate MPU regions for memory.
Fixes: 5c9d9a1b3a ("ARM: 8712/1: NOMMU: Use more MPU regions to cover memory")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
With switch to dynamic exception base address setting, VBAR/Hivecs
set only for boot CPU, but secondaries stay unaware of that. That
might lead to weird effects when trying up to bring up secondaries.
Fixes: ad475117d2 ("ARM: 8649/2: nommu: remove Hivecs configuration is asm")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Page mappings with full RWX permissions are a security risk.
x86, arm64 has an option to walk the page tables
and dump any bad pages.
(1404d6f13e
("arm64: dump: Add checking for writable and exectuable pages"))
Add a similar implementation for arm.
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Jinbum Park <jinb.park7@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This patch makes the page table dumping seq_file optional.
It makes the page table dumping code usable for other cases.
This patch refers below commit of arm64.
(ae5d1cf358
("arm64: dump: Make the page table dumping seq_file optional"))
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jinbum Park <jinb.park7@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This patch refactors the arm page table dumping code,
so multiple tables may be registered with the framework.
This patch refers below commits of arm64.
(4674fdb9f1 ("arm64: mm: dump: make page table dumping reusable"))
(4ddb9bf833 ("arm64: dump: Make ptdump debugfs a separate option"))
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Jinbum Park <jinb.park7@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
So that they don't need to indirect through the operation vector.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
The trivial direct mapping implementation already does a virtual to
physical translation which isn't strictly a noop, and will soon learn
to do non-direct but linear physical to dma translations through the
device offset and a few small tricks. Rename it to a better fitting
name.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
idmap_pgd, arch_phys_to_idmap_offset are setup once
while init stage, and never changed after that.
so, it is good candidate for __ro_after_init.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jinbum Park <jinb.park7@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Currently, with MPU enabled, we prohibit userspace access to anything
except RAM. Benjamin, reported that because of that his userspace
application cannot access framebuffer's memory he reserved in device
tree. It turns out we have no option other than to allow userspace
access memory covered by background region.
Reported-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
During kexec, we will go through kernel_kexec() -> syscore_suspend() if
CONFIG_KEXEC_JUMP is set, if not, down the road we end-up calling
kernel_restart_prepare() which invokes reboot notifiers with
SYS_RESTART.
We register a reboot notifier to make sure that the B15 read-ahead cache
is disabled, since it is another level of instruction and data cache,
and we want to avoid any potential side effects with booting a new
kernel with such a cache still turned on.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The Broadcom Brahma-B15 CPU readahead cache registers will be restored
to their Power-on-Reset values after a S3 suspend/resume cycles, so we
want to restore what we had enabled before.
Another thing we want to take care of is disabling the read-ahead cache
prior to suspending to avoid any sort of side effect with the spinlock
we need to grab to serialize register accesses.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The Broadcom Brahma-B15 readahead cache needs to be disabled,
respectively re-enable during a CPU hotplug. In case we were not to do,
CPU hotplug would occasionally fail with random crashes when a given CPU
exits the coherency domain while the RAC is still enabled, as it would
get stale data from the RAC.
In order to avoid adding any specific B15 readahead-cache awareness to
arch/arm/mach-bcm/hotplug-brcmstb.c we use a CPU hotplug state machine
which allows us to catch CPU hotplug events and disable/flush enable the
RAC accordingly.
Signed-off-by: Alamy Liu <alamyliu@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
If we detect that we are running on a Broadcom Brahma-B15 CPU, and
CONFIG_CACHE_B15_RAC is enabled, make sure that we pick-up the
b15_cache_fns function operations.
If CONFIG_CACHE_B15_RAC is enabled, but we are not running on a Broadcom
Brahma-B15 CPU, we will fallback to calling into the regular
v7_cache_fns with no cost. If CONFIG_CACHE_B15_RAC is disabled, there is
no cost and we just use the regular v7_cache_fns.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This patch adds support for the Broadcom Brahma-B15 CPU readahead cache
controller. This cache controller sits between the L2 and the memory bus
and its purpose is to provide a friendler burst size towards the DDR
interface than the native cache line size.
The readahead cache is mostly transparent, except for
flush_kern_cache_all, which is precisely what we are overriding here.
The readahead cache only intercepts reads, and does invalidate on
writes (IOW), as such, some data can remain stale in any of its buffers, such
that we need to flush it, which is an operation that needs to happen in
a particular order:
- disable the readahead cache
- flush it
- call the appropriate cache-v7.S function
- re-enable
This patch tries to minimize the impact to the cache-v7.S file by only
providing a stub in case CONFIG_CACHE_B15_RAC is enabled (default for
ARCH_BRCMSTB since it is the current user).
Signed-off-by: Alamy Liu <alamyliu@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
In preparation for adding support for the Broadcom Brahma-B15 read-ahead
cache which requires a different set of cache functions, allow the
__v7_proc macro to override the cache_fns settings, and default to
v7_cache_fns unless specified otherwise.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Avoid adding kprobes to any of the kernel entry/exit or startup
assembly code, or code in the identity-mapped region. This code does
not conform to the standard C conventions, which means that the
expectations of the kprobes code is not forfilled.
Placing kprobes at some of these locations results in the kernel trying
to return to userspace addresses while retaining the CPU in kernel mode.
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Pull ARM fixes from Russell King:
- LPAE fixes for kernel-readonly regions
- Fix for get_user_pages_fast on LPAE systems
- avoid tying decompressor to a particular platform if DEBUG_LL is
enabled
- BUG if we attempt to return to userspace but the to-be-restored PSR
value keeps us in privileged mode (defeating an issue that ftracetest
found)
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: BUG if jumping to usermode address in kernel mode
ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE
ARM: 8721/1: mm: dump: check hardware RO bit for LPAE
ARM: make decompressor debug output user selectable
ARM: fix get_user_pages_fast
Currently, for ARM kernels with CONFIG_ARM_LPAE and
CONFIG_STRICT_KERNEL_RWX enabled, the 2MiB pages mapping the
kernel code and rodata are writable. They are marked read-only in
a software bit (L_PMD_SECT_RDONLY) but the hardware read-only bit
is not set (PMD_SECT_AP2).
For user mappings, the logic that propagates the software bit
to the hardware bit is in set_pmd_at(); but for the kernel,
section_update() writes the PMDs directly, skipping this logic.
The fix is to set PMD_SECT_AP2 for read-only sections in
section_update(), at the same time as L_PMD_SECT_RDONLY.
Fixes: 1e3479225a ("ARM: 8275/1: mm: fix PMD_SECT_RDONLY undeclared compile error")
Signed-off-by: Philip Derrin <philip@cog.systems>
Reported-by: Neil Dick <neil@cog.systems>
Tested-by: Neil Dick <neil@cog.systems>
Tested-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
When CONFIG_ARM_LPAE is set, the PMD dump relies on the software
read-only bit to determine whether a page is writable. This
concealed a bug which left the kernel text section writable
(AP2=0) while marked read-only in the software bit.
In a kernel with the AP2 bug, the dump looks like this:
---[ Kernel Mapping ]---
0xc0000000-0xc0200000 2M RW NX SHD
0xc0200000-0xc0600000 4M ro x SHD
0xc0600000-0xc0800000 2M ro NX SHD
0xc0800000-0xc4800000 64M RW NX SHD
The fix is to check that the software and hardware bits are both
set before displaying "ro". The dump then shows the true perms:
---[ Kernel Mapping ]---
0xc0000000-0xc0200000 2M RW NX SHD
0xc0200000-0xc0600000 4M RW x SHD
0xc0600000-0xc0800000 2M RW NX SHD
0xc0800000-0xc4800000 64M RW NX SHD
Fixes: ded9477984 ("ARM: 8109/1: mm: Modify pte_write and pmd_write logic for LPAE")
Signed-off-by: Philip Derrin <philip@cog.systems>
Tested-by: Neil Dick <neil@cog.systems>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Pull ARM updates from Russell King:
- add support for ELF fdpic binaries on both MMU and noMMU platforms
- linker script cleanups
- support for compressed .data section for XIP images
- discard memblock arrays when possible
- various cleanups
- atomic DMA pool updates
- better diagnostics of missing/corrupt device tree
- export information to allow userspace kexec tool to place images more
inteligently, so that the device tree isn't overwritten by the
booting kernel
- make early_printk more efficient on semihosted systems
- noMMU cleanups
- SA1111 PCMCIA update in preparation for further cleanups
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (38 commits)
ARM: 8719/1: NOMMU: work around maybe-uninitialized warning
ARM: 8717/2: debug printch/printascii: translate '\n' to "\r\n" not "\n\r"
ARM: 8713/1: NOMMU: Support MPU in XIP configuration
ARM: 8712/1: NOMMU: Use more MPU regions to cover memory
ARM: 8711/1: V7M: Add support for MPU to M-class
ARM: 8710/1: Kconfig: Kill CONFIG_VECTORS_BASE
ARM: 8709/1: NOMMU: Disallow MPU for XIP
ARM: 8708/1: NOMMU: Rework MPU to be mostly done in C
ARM: 8707/1: NOMMU: Update MPU accessors to use cp15 helpers
ARM: 8706/1: NOMMU: Move out MPU setup in separate module
ARM: 8702/1: head-common.S: Clear lr before jumping to start_kernel()
ARM: 8705/1: early_printk: use printascii() rather than printch()
ARM: 8703/1: debug.S: move hexbuf to a writable section
ARM: add additional table to compressed kernel
ARM: decompressor: fix BSS size calculation
pcmcia: sa1111: remove special sa1111 mmio accessors
pcmcia: sa1111: use sa1111_get_irq() to obtain IRQ resources
ARM: better diagnostics with missing/corrupt dtb
ARM: 8699/1: dma-mapping: Remove init_dma_coherent_pool_size()
ARM: 8698/1: dma-mapping: Mark atomic_pool as __ro_after_init
..
Let's add wrappers for ->nr_ptes with the same interface as for nr_pmd
and nr_pud.
The patch also makes nr_ptes accounting dependent onto CONFIG_MMU. Page
table accounting doesn't make sense if you don't have page tables.
It's preparation for consolidation of page-table counters in mm_struct.
Link: http://lkml.kernel.org/r/20171006100651.44742-1-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The reworked MPU code produces a new warning in some configurations,
presumably starting with the code move after the compiler now makes
different inlining decisions:
arch/arm/mm/pmsa-v7.c: In function 'adjust_lowmem_bounds_mpu':
arch/arm/mm/pmsa-v7.c:310:5: error: 'specified_mem_size' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This appears to be harmless, as we know that there is always at
least one memblock, and the only way this could get triggered is
if the for_each_memblock() loop was never entered.
I could not come up with a better workaround than initializing
the specified_mem_size to zero, but at least that is the value
that the variable would have in the hypothetical case of no
memblocks.
Fixes: 877ec119db ("ARM: 8706/1: NOMMU: Move out MPU setup in separate module")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, there is assumption in early MPU setup code that kernel
image is located in RAM, which is obviously not true for XIP. To run
code from ROM we need to make sure that it is covered by MPU. However,
due to we allocate regions (semi-)dynamically we can run into issue of
trimming region we are running from in case ROM spawns several MPU
regions. To help deal with that we enforce minimum alignments for start
end end of XIP address space as 1MB and 128Kb correspondingly.
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
PMSAv7 defines curious alignment requirements to the regions:
- size must be power of 2, and
- region start must be aligned to the region size
Because of that we currently adjust lowmem bounds plus we assign
only one MPU region to cover memory all these lead to significant amount of
memory could be wasted. As an example, consider 64Mb of memory at
0x70000000 - it fits alignment requirements nicely; now, imagine that
2Mb of memory is reserved for coherent DMA allocation, so now Linux is
expected to see 62Mb of memory... and here annoying thing happens -
memory gets truncated to 32Mb (we've lost 30Mb!), i.e. MPU layout
looks like:
0: base 0x70000000, size 0x2000000
This patch tries to allocate as much as possible MPU slots to minimise
amount of truncated memory. Moreover, with this patch MPU subregions
starting to get used. MPU subregions allow us reduce the number of MPU
slots used. For example given above, MPU layout looks like:
0: base 0x70000000, size 0x2000000
1: base 0x72000000, size 0x1000000
2: base 0x73000000, size 0x1000000, disable subreg 7 (0x73e00000 - 0x73ffffff)
Where without subregions we'd get:
0: base 0x70000000, size 0x2000000
1: base 0x72000000, size 0x1000000
2: base 0x73000000, size 0x800000
3: base 0x73800000, size 0x400000
4: base 0x73c00000, size 0x200000
To achieve better layout we fist try to cover specified memory as is
(maybe with help of subregions) and if we failed, we truncate memory
to fit alignment requirements (so it occupies one MPU slot) and
perform one more attempt with the reminder, and so on till we either
cover all memory or run out of MPU slots.
Tested-by: Szemző András <sza@esh.hu>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This patch makes it possible to use MPU with v7M cores.
Tested-by: Szemző András <sza@esh.hu>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Currently, there are several issues with how MPU is setup:
1. We won't boot if MPU is missing
2. We won't boot if use XIP
3. Further extension of MPU setup requires asm skills
The 1st point can be relaxed, so we can continue with boot CPU even if
MPU is missed and fail boot for secondaries only. To address the 2nd
point we could create region covering CONFIG_XIP_PHYS_ADDR - _end and
that might work for the first stage of MPU enable, but due to MPU's
alignment requirement we could cover too much, IOW we need more
flexibility in how we're partitioning memory regions... and it'd be
hardly possible to archive because of the 3rd point.
This patch is trying to address 1st and 3rd issues and paves the path
for 2nd and further improvements.
The most visible change introduced with this patch is that we start
using mpu_rgn_info array (as it was supposed?), so change in MPU setup
done by boot CPU is recorded there and feed to secondaries. It
allows us to keep minimal region setup for boot CPU and do the rest in
C. Since we start programming MPU regions in C evaluation of MPU
constrains (number of regions supported and minimal region order) can
be done once, which in turn open possibility to free-up "probe"
region early.
Tested-by: Szemző András <sza@esh.hu>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Currently, inline assembly for accessing to MPU's cp15 lacks volatile
keyword which opens possibility to compiler to optimise such accesses
as soon as we start using them more intensively. Rather than fixing
inline asm, lets move MPU accessors to use cp15 helpers which do the
right thing.
Tested-by: Szemző András <sza@esh.hu>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Having MPU handling code in dedicated module makes it easier to
enhance/maintain it.
Tested-by: Szemző András <sza@esh.hu>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Some nommu systems have RAM at address 0. When vectors are not located
there, the very beginning of memory remains available for dynamic
allocations. The memblock allocator explicitly skips the first page
but the standard page allocator does not, and while it correctly returns
a non-null struct page pointer for that page, page_address() gives 0
which gets confused with NULL (out of memory) by callers despite having
plenty of free memory left.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
There are no users of init_dma_coherent_pool_size() left due to
387870f ("mm: dmapool: use provided gfp flags for all
dma_alloc_coherent() calls"), so remove it.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
atomic_pool is setup once while init stage and never changed after
that, so it is good candidate for __ro_after_init.
Since we are here mark atomic_pool_size with __init_data.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
gen_pool_first_fit_order_align() does not make use of additional data,
so pass plain NULL there.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The code in question checks memory constrains to set default policy for
overcommit; however we support page size of 4K only thus condition is
always evaluated to false. Remove that dead code.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Pull ARM updates from Russell King:
"Low priority fixes and updates for ARM:
- add some missing includes
- efficiency improvements in system call entry code when tracing is
enabled
- ensure ARMv6+ is always built as EABI
- export save_stack_trace_tsk()
- fix fatal signal handling during mm fault
- build translation table base address register from scratch
- appropriately align the .data section to a word boundary where we
rely on that data being word aligned"
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8691/1: Export save_stack_trace_tsk()
ARM: 8692/1: mm: abort uaccess retries upon fatal signal
ARM: 8690/1: lpae: build TTB control register value from scratch in v7_ttb_setup
ARM: align .data section
ARM: always enable AEABI for ARMv6+
ARM: avoid saving and restoring registers unnecessarily
ARM: move PC value into r9
ARM: obtain thread info structure later
ARM: use aliases for registers in entry-common
ARM: 8689/1: scu: add missing errno include
ARM: 8688/1: pm: add missing types include
When there's a fatal signal pending, arm's do_page_fault()
implementation returns 0. The intent is that we'll return to the
faulting userspace instruction, delivering the signal on the way.
However, if we take a fatal signal during fixing up a uaccess, this
results in a return to the faulting kernel instruction, which will be
instantly retried, resulting in the same fault being taken forever. As
the task never reaches userspace, the signal is not delivered, and the
task is left unkillable. While the task is stuck in this state, it can
inhibit the forward progress of the system.
To avoid this, we must ensure that when a fatal signal is pending, we
apply any necessary fixup for a faulting kernel instruction. Thus we
will return to an error path, and it is up to that code to make forward
progress towards delivering the fatal signal.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reading TTBCR in early boot stage might return the value of the previous
kernel's configuration, especially in case of kexec. For example, if
normal kernel (first kernel) had run on a configuration of PHYS_OFFSET <=
PAGE_OFFSET and crash kernel (second kernel) is running on a configuration
PHYS_OFFSET > PAGE_OFFSET, which can happen because it depends on the
reserved area for crash kernel, reading TTBCR and using the value to OR
other bit fields might be risky because it doesn't have a reset value for TTBCR.
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Hoeun Ryu <hoeun.ryu@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Robert Jarzmik reports that his PXA25x system fails to boot with 4.12,
failing at __flush_whole_cache in arch/arm/mm/proc-xscale.S:215:
0xc0019e20 <+0>: ldr r1, [pc, #788]
0xc0019e24 <+4>: ldr r0, [r1] <== here
with r1 containing 0xc06f82cd, which is the address of "clean_addr".
Examination of the System.map shows:
c06f22c8 D user_pmd_table
c06f22cc d __warned.19178
c06f22cd d clean_addr
indicating that a .data.unlikely section has appeared just before the
.data section from proc-xscale.S. According to objdump -h, it appears
that our assembly files default their .data alignment to 2**0, which
is bad news if the preceding .data section size is not power-of-2
aligned at link time.
Add the appropriate .align directives to all assembly files in arch/arm
that are missing them where we require an appropriate alignment.
Reported-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The way how default DMA pool is exposed has changed and now we need to
use dedicated interface to work with it. This patch makes alloc/release
operations to use such interface. Since, default DMA pool is not
handled by generic code anymore we have to implement our own mmap
operation.
Tested-by: Andras Szemzo <sza@esh.hu>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Christoph noticed [1] that default DMA pool in current form overload
the DMA coherent infrastructure. In reply, Robin suggested [2] to
split the per-device vs. global pool interfaces, so allocation/release
from default DMA pool is driven by dma ops implementation.
This patch implements Robin's idea and provide interface to
allocate/release/mmap the default (aka global) DMA pool.
To make it clear that existing *_from_coherent routines work on
per-device pool rename them to *_from_dev_coherent.
[1] https://lkml.org/lkml/2017/7/7/370
[2] https://lkml.org/lkml/2017/7/7/431
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Andras Szemzo <sza@esh.hu>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Pull ARM updates from Russell King:
- add support for ftrace-with-registers, which is needed for kgraft and
other ftrace tools
- support for mremap() for the sigpage/vDSO so that checkpoint/restore
can work
- add timestamps to each line of the register dump output
- remove the unused KTHREAD_SIZE from nommu
- align the ARM bitops APIs with the generic API (using unsigned long
pointers rather than void pointers)
- make the configuration of userspace Thumb support an expert option so
that we can default it on, and avoid some hard to debug userspace
crashes
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8684/1: NOMMU: Remove unused KTHREAD_SIZE definition
ARM: 8683/1: ARM32: Support mremap() for sigpage/vDSO
ARM: 8679/1: bitops: Align prototypes to generic API
ARM: 8678/1: ftrace: Adds support for CONFIG_DYNAMIC_FTRACE_WITH_REGS
ARM: make configuration of userspace Thumb support an expert option
ARM: 8673/1: Fix __show_regs output timestamps
In this new subsystem we'll try to properly maintain all the generic
code related to dma-mapping, and will further consolidate arch code
into common helpers.
This pull request contains:
- removal of the DMA_ERROR_CODE macro, replacing it with calls
to ->mapping_error so that the dma_map_ops instances are
more self contained and can be shared across architectures (me)
- removal of the ->set_dma_mask method, which duplicates the
->dma_capable one in terms of functionality, but requires more
duplicate code.
- various updates for the coherent dma pool and related arm code
(Vladimir)
- various smaller cleanups (me)
-----BEGIN PGP SIGNATURE-----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=0Fso
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping infrastructure from Christoph Hellwig:
"This is the first pull request for the new dma-mapping subsystem
In this new subsystem we'll try to properly maintain all the generic
code related to dma-mapping, and will further consolidate arch code
into common helpers.
This pull request contains:
- removal of the DMA_ERROR_CODE macro, replacing it with calls to
->mapping_error so that the dma_map_ops instances are more self
contained and can be shared across architectures (me)
- removal of the ->set_dma_mask method, which duplicates the
->dma_capable one in terms of functionality, but requires more
duplicate code.
- various updates for the coherent dma pool and related arm code
(Vladimir)
- various smaller cleanups (me)"
* tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping: (56 commits)
ARM: dma-mapping: Remove traces of NOMMU code
ARM: NOMMU: Set ARM_DMA_MEM_BUFFERABLE for M-class cpus
ARM: NOMMU: Introduce dma operations for noMMU
drivers: dma-mapping: allow dma_common_mmap() for NOMMU
drivers: dma-coherent: Introduce default DMA pool
drivers: dma-coherent: Account dma_pfn_offset when used with device tree
dma: Take into account dma_pfn_offset
dma-mapping: replace dmam_alloc_noncoherent with dmam_alloc_attrs
dma-mapping: remove dmam_free_noncoherent
crypto: qat - avoid an uninitialized variable warning
au1100fb: remove a bogus dma_free_nonconsistent call
MAINTAINERS: add entry for dma mapping helpers
powerpc: merge __dma_set_mask into dma_set_mask
dma-mapping: remove the set_dma_mask method
powerpc/cell: use the dma_supported method for ops switching
powerpc/cell: clean up fixed mapping dma_ops initialization
tile: remove dma_supported and mapping_error methods
xen-swiotlb: remove xen_swiotlb_set_dma_mask
arm: implement ->dma_supported instead of ->set_dma_mask
mips/loongson64: implement ->dma_supported instead of ->set_dma_mask
...
Pull ARM fix from Russell King:
"One final fix for 4.12 - Doug found a boot failure case triggered by
requesting a non-even MB vmalloc size"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8685/1: ensure memblock-limit is pmd-aligned
Linus Torvalds