* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (75 commits)
mmc: core: eMMC bus width may not work on all platforms
mmc: sdhci: Auto-CMD23 fixes.
mmc: sdhci: Auto-CMD23 support.
mmc: core: Block CMD23 support for UHS104/SDXC cards.
mmc: sdhci: Implement MMC_CAP_CMD23 for SDHCI.
mmc: core: Use CMD23 for multiblock transfers when we can.
mmc: quirks: Add/remove quirks conditional support.
mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver
mmc: sdhci-pxa: Add quirks for DMA/ADMA to match h/w
mmc: core: duplicated trial with same freq in mmc_rescan_try_freq()
mmc: core: add support for eMMC Dual Data Rate
mmc: core: eMMC signal voltage does not use CMD11
mmc: sdhci-pxa: add platform code for UHS signaling
mmc: sdhci: add hooks for setting UHS in platform specific code
mmc: core: clear MMC_PM_KEEP_POWER flag on resume
mmc: dw_mmc: fixed wrong regulator_enable in suspend/resume
mmc: sdhi: allow powering down controller with no card inserted
mmc: tmio: runtime suspend the controller, where possible
mmc: sdhi: support up to 3 interrupt sources
mmc: sdhi: print physical base address and clock rate
...
Enable fast bcm4329 WIFI suspend/resume on Tegra2 board.
This patch allows the mach-tegra support to tell the tegra MMC host
controller to NOT turn off power for the MMC controller the WIFI part
lives behind. Thus bcm4329 firmware doesn't need to be reloaded.
Signed-off-by: Venkat Rao <vrao@broadcom.com>
Tested-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Olof Johansson <olof@lixom.net>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (137 commits)
ARM: bcmring: convert to use sp804 clockevents
ARM: bcmring: convert to sp804 clocksource
ARM: 6912/1: bcmring: Add clkdev table in init_early
clockevents: ARM sp804: obtain sp804 timer rate via clks
clockevents: ARM sp804: allow clockevent name to be specified
clocksource: ARM sp804: obtain sp804 timer rate via clks
clocksource: ARM sp804: allow clocksource name to be specified
clocksource: convert OMAP1 to 32-bit down counting clocksource
clocksource: convert MXS timrotv2 to 32-bit down counting clocksource
clocksource: convert SPEAr platforms 16-bit up counting clocksource
clocksource: convert Integrator/AP 16-bit down counting clocksource
clocksource: convert W90x900 24-bit down counting clocksource
clocksource: convert ARM 32-bit down counting clocksources
clocksource: convert ARM 32-bit up counting clocksources
clocksource: add common mmio clocksource
ARM: update sa1100 to reflect PXA updates
ARM: omap1: convert to using readl/writel instead of volatile struct
ARM: omap1: delete useless interrupt handler
ARM: s5p: consolidate selection of timer register
ARM: 6939/1: fix missing 'cpu_relax()' declaration
...
Rather than having each platform class provide a mach/smp.h header for
smp_cross_call(), arrange for them to register the function with the
core ARM SMP code instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since mandatory barriers may be used (explicitly or implicitly via readl
etc.) to ensure the ordering between Device and Normal memory accesses,
a DMB is not enough. This patch converts it to a DSB.
Cc: Colin Cross <ccross@android.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tegra hardware design cannot reliably support an arbitrary set of keys
waking up the system. Modify wakeup logic so either any key wakes the
system up or none will do.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Now that irq.c is just an interface layer between the gic
and legacy_irq.c, move the contents of legacy_irq.c into
irq.c.
Signed-off-by: Colin Cross <ccross@android.com>
Tegra PM irq support is being improved, remove it for now
until the rest of the platform gets PM support.
Signed-off-by: Colin Cross <ccross@android.com>
Seaboard derivate Kaen has a GPIO to mute the headphone output. Add a field
to tegra_wm8903_platform_data so the board files can pass the GPIO number
for that to the ASoC machine driver.
Also, initialize this new field to a "not present" value for Harmony.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The audio driver will soon support more than just the Tegra Harmony board.
Rename the platform data header file and data type to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (91 commits)
ARM: 6806/1: irq: introduce entry and exit functions for chained handlers
ARM: 6781/1: Thumb-2: Work around buggy Thumb-2 short branch relocations in gas
ARM: 6747/1: P2V: Thumb2 support
ARM: 6798/1: aout-core: zero thread debug registers in a.out core dump
ARM: 6796/1: Footbridge: Fix I/O mappings for NOMMU mode
ARM: 6784/1: errata: no automatic Store Buffer drain on Cortex-A9
ARM: 6772/1: errata: possible fault MMU translations following an ASID switch
ARM: 6776/1: mach-ux500: activate fix for errata 753970
ARM: 6794/1: SPEAr: Append UL to device address macros.
ARM: 6793/1: SPEAr: Remove unused *_SIZE macros from spear*.h files
ARM: 6792/1: SPEAr: Replace SIZE macro's with SZ_4K macros
ARM: 6791/1: SPEAr3xx: Declare device structures after shirq code
ARM: 6790/1: SPEAr: Clock Framework: Rename usbd clock and align apb_clk entry
ARM: 6789/1: SPEAr3xx: Rename sdio to sdhci
ARM: 6788/1: SPEAr: Include mach/hardware.h instead of mach/spear.h
ARM: 6787/1: SPEAr: Reorder #includes in .h & .c files.
ARM: 6681/1: SPEAr: add debugfs support to clk API
ARM: 6703/1: SPEAr: update clk API support
ARM: 6679/1: SPEAr: make clk API functions more generic
ARM: 6737/1: SPEAr: formalized timer support
...
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (172 commits)
USB: Add support for SuperSpeed isoc endpoints
xhci: Clean up cycle bit math used during stalls.
xhci: Fix cycle bit calculation during stall handling.
xhci: Update internal dequeue pointers after stalls.
USB: Disable auto-suspend for USB 3.0 hubs.
USB: Remove bogus USB_PORT_STAT_SUPER_SPEED symbol.
xhci: Return canceled URBs immediately when host is halted.
xhci: Fixes for suspend/resume of shared HCDs.
xhci: Fix re-init on power loss after resume.
xhci: Make roothub functions deal with device removal.
xhci: Limit roothub ports to 15 USB3 & 31 USB2 ports.
xhci: Return a USB 3.0 hub descriptor for USB3 roothub.
xhci: Register second xHCI roothub.
xhci: Change xhci_find_slot_id_by_port() API.
xhci: Refactor bus suspend state into a struct.
xhci: Index with a port array instead of PORTSC addresses.
USB: Set usb_hcd->state and flags for shared roothubs.
usb: Make core allocate resources per PCI-device.
usb: Store bus type in usb_hcd, not in driver flags.
usb: Change usb_hcd->bandwidth_mutex to a pointer.
...
Interface used by Tegra's gadget driver and ehci driver
to power on and configure the USB PHYs.
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To give one place to setup the pins that are used as GPIOs instead
of as their pinmuxed functions. Specifying enabled as false explicitly
disables the gpio mode of that pin (if left on by firmware).
This should remove the need for calling these from specific drivers and
thus reduce tegra-specific code from them.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Erik Gilling <konkers@android.com>
The SDMMC controllers have extra bits in the clock source
register that adjust the delay between the clock and data
to compenstate for delays on the PCB. The values need to
be set from the clock code so the clock can be locked
during the read-modify-write on the clock source register.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Give each clock its own lock, and remove all lock traversals from
parent to child clocks to prevent AB-BA deadlocks.
This brings the locking in line with the common struct clk
patches and should make conversion simple.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The existing version did not extend well to core dvfs, drop it
for now until the new clk api with clk_prepare and clk_unprepare
is ready and non-atomic clocks are possible.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Add Fn keymap support to allow for internal processing of Fn keys.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This uncouple PHYS_OFFSET from the platform definitions, thereby
facilitating run-time computation of the physical memory offset.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds gart, hdmi, avp, host1x, and pwm controllers to mach/iomap.h
Signed-off-by: Gary King <gking@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Adds missing drive pingroups, saves all drive pingroups in
suspend, and restores the pinmux registers in the proper order.
Signed-off-by: Gary King <gking@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Add fields to describe all the audio-related GPIOs on Harmony, except for
the codec's GPIO IRQ, which will be passed in its i2c_board_info.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - pass touch resolution to clients through input_absinfo
Input: wacom - add 2 Bamboo Pen and touch models
Input: sysrq - ensure sysrq_enabled and __sysrq_enabled are consistent
Input: sparse-keymap - fix KEY_VSW handling in sparse_keymap_setup
Input: tegra-kbc - add tegra keyboard driver
Input: gpio_keys - switch to using request_any_context_irq
Input: serio - allow registered drivers to get status flag
Input: ct82710c - return proper error code for ct82c710_open
Input: bu21013_ts - added regulator support
Input: bu21013_ts - remove duplicate resolution parameters
Input: tnetv107x-ts - don't treat NULL clk as an error
Input: tnetv107x-keypad - don't treat NULL clk as an error
Fix up trivial conflicts in drivers/input/keyboard/Makefile due to
additions of tc3589x/Tegra drivers
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@google.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the internal matrix keyboard controller for
Nvidia Tegra platforms.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
SDHCI driver for Tegra. This driver plugs in as a new variant of
sdhci-pltfm, using the platform data structure passed in to specify the
GPIOs to use for card detect, write protect and card power enablement.
Original driver (of which only the header file is left):
Signed-off-by: Yvonne Yip <y@palm.com>
The rest, which has been rewritten by now:
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Chris Ball <cjb@laptop.org>
With "ARM: CPU hotplug: remove bug checks in platform_cpu_die()", we
now do not use hard_smp_processor_id(), we no longer need to read the
hardware processor ID. Remove the include providing this function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds