When scanning, it is somewhat important to scan
on the correct virtual interface. All drivers
that currently implement hw_scan only support a
single virtual interface, but that may change
and then we'd want to be ready.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If bit 29 is set, MAC H/W can attempt to decrypt the received aggregate
with WEP or TKIP, eventhough the received frame may be a CRC failed
corrupted frame. If this bit is set, H/W obeys key type in keycache.
If it is not set and if the key type in keycache is neither open nor
AES, H/W forces key type to be open. But bit 29 should be set to 1
for AsyncFIFO feature to encrypt/decrypt the aggregate with WEP or TKIP.
Cc: stable@kernel.org
Reported-by: Johan Hovold <johan.hovold@lundinova.se>
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: Ranga Rao Ravuri <ranga.ravuri@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX interrupt mitigation reduces the number of interrupts
by addressing several interrupt actions (AR_IMR_TXOK,
AR_IMR_TXDESC) all in one interrupt so when enabling
it discard setting the other interrupts.
Without this TX interrupt mitigation would actually
increase the number of interrupts two-fold. We still
leave TX interrupt mitigation disabled as it is still
being tested.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the noisefloor calibration times out, do not load -50 into
the registers, since this might cause rx issues. Instead, leave
enough time for the noise floor calibration to complete until
the next check.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the new AR9003 EEPROM code does tune the card for the configured
tx power level, we need to fill in the correct power limits in the TPC
part of the DMA descriptor.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Combine multiple checks that were supposed to check for the same
conditions, but didn't. Always enable fast PLL clock on AR9280 2.0
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fast clock operation (44Mhz) is enabled for 5Ghz in ar9003, so
take care of the conversion from usec to hw clock.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable TX IQ calibration, it was prematurely enabled in
previous versions.
Cc: Paul Shaw <Paul.Shaw@Atheros.com>
Cc: Thomas Hammel <Thomas.Hammel@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This synchs up the initvals to the values used on the
Atheros HAL for AR9003. This specific change adds support
for a new high power module.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A bunch of validation and processing in the RX IRQ handler
can be moved to the RX tasklet. The IRQ handler is
already heavy, with the memory allocation for handling
stream mode. Also, a memcpy of 40 bytes for every packet
can be avoided in the handler.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for the endpoint IDs when processing
TX completions and drop the unsupported EPIDs.
We can add other endpoints (UAPSD,..) when support
is added.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the same type of configurable debug messages to libertas_tf as
already exist in the libertas driver. This has facilitated creation
of a interface specification and will facilitate future development
of this driver.
Signed-off-by: Steve deRosier <steve@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restore the rfcsr initialization for RT305x SoC devices which was removed
by "rt2x00: Finish rt3070 support in rt2800 register initialization.".
This fixes the rx path on SoC devices.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a typo in a comment in rt2800.h. Instead of replacing the wrong
hexvalue (0x171c) with the correct one (0x1718) just use the appropriate
readable define.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get closer to what the ralink driver does by setting the rf register 13
to tx_power2 during channel switch.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable HT40 support for now as it causes rx problems with HT40 capable
11n APs (when mac80211 enables HT40, rx is completely disfunctional).
Once the rt2800 HT code is capable of using HT40 we should enable the
flag again.
I only tested this patch with a rt305x SoC device, nevertheless the
patch disables HT40 also on PCI and USB rt2800 devices.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All commands to the target are disabled when the device
is unplugged, but a normal module unload has to be
differentiated from this case, as we could still receive
data in the RX endpoint. Fix this by checking if the
device is attached or not.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My patch "ath9k_htc: Handle WMI timeouts properly" introduced
a race condition in WMI command processing. The last issued command
should be stored _before_ issuing a WMI command. Not doing this
would result in the WMI event IRQ dropping correct command responses
as invalid.
Fix this race by storing the command id correctly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Completion of WMI commands take a longer time
on some platforms. Increase the timeout value
to handle this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When handling the REGIN callback, processing
the incoming data first should be the preferred
mode of operation. Allocation of a new SKB may fail,
in which case, the URB will not be resubmitted.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So, apparently there is a USB reboot command
that the target accepts. Using this instead of
usb_reset_device() fixes the issue of "descriptor read error"
that pops up on repeated load/unload.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the TX callback, the HTC layer has to pass the
priv pointer that was registered during service initialization.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason to disable the PHY Error / MIB counters
when the module is being unloaded.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a code segment in configpciepowersave()
to make use of multiple register writes.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the USB device has been unplugged, there is
no point in trying to send commands to the target.
Fix this by denying all WMI commands in such a case.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies URB management for transmission,
by removing the 'FLUSH' variable (which is not needed,
since we can determine if the URB has been killed by
looking at the URB status), and also handling the STOP
case properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a recently introduced use-after-free regression
from "p54pci: prevent stuck rx-ring on slow system".
Hans de Goede reported a use-after-free regression:
>BUG: unable to handle kernel paging request at 6b6b6b6b
>IP: [<e122284a>] p54p_check_tx_ring+0x84/0xb1 [p54pci]
>*pde = 00000000
>Oops: 0000 [#1] SMP
>EIP: 0060:[<e122284a>] EFLAGS: 00010286 CPU: 0
>EIP is at p54p_check_tx_ring+0x84/0xb1 [p54pci]
>EAX: 6b6b6b6b EBX: df10b170 ECX: 00000003 EDX: 00000001
>ESI: dc471500 EDI: d8acaeb0 EBP: c098be9c ESP: c098be84
> DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
>Process swapper (pid: 0, ti=c098a000 task=c09ccfe0 task.ti=c098a000)
>Call Trace:
> [<e1222b02>] ? p54p_tasklet+0xaa/0xb5 [p54pci]
> [<c0440568>] ? tasklet_action+0x78/0xcb
> [<c0440ed3>] ? __do_softirq+0xbc/0x173
Quote from comment #17:
"The problem is the innocent looking moving of the tx processing to
after the rx processing in the tasklet. Quoting from the changelog:
This patch does it the same way, except that it also prioritize
rx data processing, simply because tx routines *can* wait.
This is causing an issue with us referencing already freed memory,
because some skb's we transmit, we immediately receive back, such
as those for reading the eeprom (*) and getting stats.
What can happen because of the moving of the tx processing to after
the rx processing is that when the tasklet first runs after doing a
special skb tx (such as eeprom) we've already received the answer
to it.
Then the rx processing ends up calling p54_find_and_unlink_skb to
find the matching tx skb for the just received special rx skb and
frees the tx skb.
Then after the processing of the rx skb answer, and thus freeing
the tx skb, we go process the completed tx ring entires, and then
dereference the free-ed skb, to see if it should free free-ed by
p54p_check_tx_ring()."
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=583623
Bug-Identified-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hans de Goede identified a bug in p54p_check_tx_ring:
there are two ring indices. 1 => tx data and 3 => tx management.
But the old code had a constant "1" and this resulted in spurious
dma unmapping failures.
Cc: stable@kernel.org
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=583623
Bug-Identified-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes ar5416Addac_9160 and ar5416Addac_9160 const
I guess we skipped them long ago.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Supported only for single stream rates by the hardware
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9300 based hardware can 3x3 MCS rates, this should be set in the
HT capabilities.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of increasing bits_per_symbol for supporting more streams, keep
it single-stream only and multiply the values by the numer of streams.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Include MCS0-31 and also add SGI for HT20. This makes it
possible to support more different rate combinations with
newer hardware.
Based on a patch by Selvam. T.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the first element of survey data, the noise floor figure.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the survey function to both mac80211 itself and to mac80211_hwsim.
For the latter driver, we simply invent some noise level.A real driver which
cannot determine the real channel noise MUST NOT report any noise, especially
not a magically conjured one :-)
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I set up multiple VAPs with ath9k, I encountered an issue that
the traffic may be lost after a while.
The detailed phenomenon is
1. After a while the clients connected to one of these VAPs will get
into a state that no broadcast/multicast packets can be transfered
successfully while the unicast packets can be transfered normally.
2. Minutes latter the unitcast packets transfer will fail as well,
because the ARP entry is expired and it can't be freshed due to the
broadcast trouble.
It's caused by the group key overwritten and someone discussed this
issue in ath9k-devel maillist before, but haven't work out a fix yet.
I referred the method in madwifi, and made a patch for ath9k.
The method is to set the high bit of the sender(AP)'s address, and
associated that mac and the group key. It requires the hardware
supports multicast frame key search. It seems true for AR9160.
Not sure whether it's the correct way to fix this issue. But it seems
to work in my test. The patch is attached, feel free to revise it.
Signed-off-by: Daniel Yingqiang ma <yma.cool@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Applied common sense, no info from the manufacturer:
(0x8516, 0x2070) is RT2070
(0x8516, 0x2770) is RT2770
(0x8516, 0x2870) is RT2870
[...]
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Orinoco should be endian clean, so enable the checking.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... to set fragmentation and RTS thresholds. Also report RTS retry
settings during wiphy init.
Note that the existing semantics for enabling microwave robustness are
preserved on firmwares that have it.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some future hardware will also require some antenna
overrides so make the current logic more generic;
right now it is semantically based on a workaround
for off-channel reception but the reasons for the
new antenna overrides will be different.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Off-channel reception is acceptable in monitor
mode, and checking for monitor mode this way is
not really correct anyway since it could be the
case while operating.
Now iwl_is_monitor_mode() is no longer used so
remove it completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Monitor mode operation need not (and probably should
not) affect scanning this way since real monitoring
can not properly happen while scanning anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The flag name is a little misleading, this
flag instructs the device to ignore bluetooth
messages for purposes of frame transmissions,
so rename the flag to TX_CMD_FLG_IGNORE_BT.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Some future hardware will require a different command to
be sent for bluetooth coexist, so make this a virtual
method that can be changed on a per-device basis.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since multiple new devices having similar uCode architecture and use same
registers address, remove more reference to 5000 series to eliminate the
confusion.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Perform sanity check for turn on aggregation tid. Also remove the
option for turn on all the aggregation tids at once since it is
deprecated function and not being used.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For 6000g2 series of NICs, PA type is determined by uCode, driver do not
have to set the register for internal/external PA. It is a workaround
just for 6000 series NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Add hardware revision for 6000g2 series of NIC
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This function is called twice in a row, remove the second one.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Use the show uCode statistics function for uCode debugging purposes only; it
is being duplicated in both debugfs and sysfs. remove the one from sysfs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This patch is to bring up 6000 Series 2x2 AGN Gen2 adapters.
Seperate various version numbers from 6000 Series definitions;
Add module firmware declaration for the new adapters;
Add additional device IDs and subsystem IDs;
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Some definition for eeprom apply to more than 5000 series device, change
the name to reflect it for easy reading.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Scan requesting doesn't need to be asynchronous
since all code paths leading up to it can sleep.
Make the scan request a new util operation that
is hw-specific (to account for 3945 vs. agn)
and call it right in place.
This patch moves a lot of code into iwlagn as
it need not be in iwlcore.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
I keep checking what "priv->scan" is, so rename
it to "priv->scan_cmd" which more clearly tells
us what it is.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since we no longer do a multi-pass scan,
keeping track of how long each pass took
is pointless since there will only be one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This logic is just confusing, if anything it
belongs into mac80211. Also, even if we do
scan during the EAPOL handshake, that will
not cause any problems, just a short delay.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
With atomic bitops, test_and_{set,clear}_bit
should be used instead of separate test_bit
and set_bit/clear_bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since mac80211 will now never request scanning
multiple bands, we can remove all the associated
logic and scan a single band only in each scan.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Even the initial single/dual stream values will be overridden later when
issue link quality command; but still make sense not to use hard-code
value during initialization. Single/Dual stream mask are used to indicate the
best antenna for SISO/MIMO; different NIC has different tx antenna
configuration; so the parameter need to based on the valid tx antenna.
1x2 device: single tx antenna available, only SISO is valid
configuration, but still need to set up MIMO configuration, so set it up
with antenna A & B as default.
2x2 device: two tx antenna available, dual_stream will use both valid
antenna.
3x3 device: three tx antenna available, skip the first antenna and
choice the second and third antenna for dual_stream.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For 6000 series, the 2.4G HT40 band regulatory settings address in EEPROM
was off by 2.
Before the fix, you'll see this in dmesg:
[79535.788877] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
[79535.788880] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
And after the fix:
[91132.688706] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
[91132.688709] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When an internal scan is started, nothing protects the
is_internal_short_scan variable which can cause crashes,
cf. https://bugzilla.kernel.org/show_bug.cgi?id=15667.
Fix this by making the short scan request use the mutex
for locking, which requires making the request go to a
work struct so that it can sleep.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_wimax_coex_cmd.flags can be really uninitialized, so fix
that.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In mac80211 we always check both scan_req->ie and scan_req->ie_len
against zero before usage, in iwlwifi we should do the same.
Remove not needed "left -= ie_len" while at it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251 has WLAN_IRQ pin for generating interrupts to host processor,
which is mandatory in SPI mode and optional in SDIO mode (which can
use SDIO interrupts instead). However TI recommends using deditated
IRQ line for SDIO too.
Add support for using dedicated interrupt line with SDIO, but also leave
ability to switch to SDIO interrupts in case it's needed.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bunch of endian issues that
were exposed by sparse. It's a miracle that the driver
worked at all till now.
The Lord be praised.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a WMI command has timed out for some reason,
a late WMI response would end up updating the
response region of a new WMI request that has been
issued in the meantime.
Fix this race condition by dropping a WMI response
if a new WMI command has been issued.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no point in trying to set the LED pin
when the module is being unloaded. The target
would be reset anyway.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds macros at certain places
which could be optimized for multiple register writes.
The performance of ath9k_htc improves considerably,
especially reducing the latency involved in a scan run.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Programming the opmode in the HW can be done
before the assoc_id and STA_ID registers are
setup. This helps ath9k_htc when multiple register
writes are used.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for writing multiple registers
in a single USB command.
Specific calls from the HW code that performs multiple
register writes would be modified to make use of this
in subsequent patches.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required to implement delayed/buffered
register writes in ath9k_htc.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up beacon configuration,
removing a redundant interface type check
and updating beacon interval in the correct place.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add -D__CHECK_ENDIAN__ to driver ccflags so that sparse will
always check endianness by default.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to tests, both TSF lower and upper registers kept counting, so
the higher part could have been updated after the lower part has been
read, as shown in the following log where the upper part is read first
and the lower part next.
tsf = {00000003-fffffffd}
tsf = {00000003-00000001}
tsf = {00000004-0000000b}
This patch corrects this by checking that the upper part has not been
changed while the lower part was read. It has been tested in an IBSS
network where artifical IBSS merges have been done in order to trigger
hundreds of rollover for the TSF lower part.
It follows the logic mentionned by Derek, with only 2 register reads
needed at each additional steps instead of 3 (the minimum number of
register reads is still 3).
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The first AR9003 hardware family device supported is the
AR9300, which has the vendor:device id 168c:0030
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LDPC is enabled by the rate control if the its determined
that the target peer supports LDPC. We would have already
intersected the HT capabilities so if our peer supports
LDPC so do we.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also add a function to clean up tx status ring.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable CRC check on the descriptor fetched from host on AR9003
upon reseting the TX queue.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also reset tx status ring suring chip reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9002 hardware code enables aggregation for WEP but
mac80211 doesn't enable aggregation with WEP, and the AR9003
code family does not need this so skip it for now for AR9003
but leave the code and annotate we should eventually consider
how to remove this in consideration for the HAL unification
goals.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asynch fifo code is specific to >= AR9287 so stuff it
into the AR9002 hardware family code and skip it for AR9003
cards.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is done depending on what the EEPROM settings indicates.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We add this now as OFDM spur mitigation required accessing
the EEPROM for the AR9003 devices.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once upon a time the AR_EEPROM_MAC macro was added to let us
add a random attribute to the three 4-bytes of MAC addresses
entries we read from the EEPROM. This was good while a random
high-enough value was used which did not conflict with any
of the already existing enum eeprom_param values. With AR9003
support the enums overlap and it means we either increment
the random offset or just restore the reading logic to match
what the HAL has. I choose to do the later to synchronize
the logic on both code bases.
This should fix reading the MAC address from the EEPROM
on AR9003 hardware.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This goes with some new shiny TX IQ calibration that AR9003
hardware family supports.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the last call on calib.c which acceses PHY stuff,
with this change we calib.c is now generic between both
all supported hardware families.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is so we can share routines which access this register
on calib.c
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also move interrupt related code to mac.c
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9003 TX/RX gain is currently initialized with the other
components, so for now AR9003 does not implment this callback,
after hardware bring up we can test moving the TX/RX gain there
as well and if it works well move them to its own callback as
well.
Since all INI stuff is now moved out hw.c no longer needs to
include and touch any original INI headers/structs.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is specific to the AR9002 family only.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move out the generic hardware family code out into their own
files, we have one for AR5008, AR9001, and AR9002 family (ar9002_hw.c)
and another file for the new AR9003 hardware family (ar9003_hw.c).
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calibration code touches phy registers and since these
change the calibration code needs to be abstracted.
Noise floor calibration is the only thing remaining but
since the remaining calls only touch the AR_PHY_AGC_CONTROL
register we'll just define that register conditionally, that
will be done separately. The goal is to remove the dependency
of ar9002_phy.h on calib.c
This also adds stubs to be filled for AR9003 calibration code.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calibration settings should go into the respective
hardware family AR9002 calibration settings callback,
ar9002_hw_init_cal_settings().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can do the family revision check on the top level caller.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're bailing out on the alternative code path so remove the
else branch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Open Loop Control temperature compensation changes between our
hardware so use a helper for it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code can be simplified and shared between two locations if we bring
this into a helper. During reset we do not account for the skip count.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can reorganize the code in such a way that eep_map can be removed,
which makes the code more clearer.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Store appropriate desc length which will be used by the
ath9k module while duplicating tx desc.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9003 hardware family now initializes hardware by block
components and into stages: pre, core and init.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The initvals.h file is over 7000 lines now, so instead of adding
AR9003 initvals to it instead lets split the current initvals.h by
hardware family: AR5008, AR9001, AR9002
The AR9003 family will have its own initval file later.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, no need for the udelay(2) on AR9003 hardware.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9003 family requires a change on the loop and can also skip
testing the PHY timing registers. This chip test can now be used
by all Atheros hardware families, including legacy. We can
eventually move this out to the generic ath module.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Set rx buf size in register 0x60
* Set rxdp on the respective hw rx queue (HP and LP queues)
* Process rx descriptor
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HP & LP queue depth and rx status length.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 supports extended DMA (EDMA), this comes with some
bells and whistles on top of the legacy DMA that we are used
to. Mark AR9003 and later chips EDMA capable.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI is still being debugged on AR9003 by our systems team
so it should not yet be enabled yet. When ANI will be
enabled all ANI functionality is expected to be enabled
so fill the ANI functionality to all for AR9003 for now
as well.
Cc: Enis Akay <Enis.Akay@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows us to add SREV checks on these helpers.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This add stubs for PHY support for the AR9003 hardware family.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, clean up and reorganize the AR9287 macro to have better
ordering. We won't add the PCI ID to the supported device list
until we have some functional code for it.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PLL control computation used to program the AR_RTC_PLL_CONTROL
register varies between our harware so just add a private callback for it.
AR9003 will use its own callback.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not required for the AR9003 family.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PHY split is easier done in a few steps. First move
the RF ops to the private ops and rename them accordingly.
We split PHY stuff up first for the AR5008 and AR9002
families. There are some callbacks that AR9002 share
with the AR5008 familiy so we set those first, if AR9002
has some different callbacks it will override them upon
hardware init.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used only once by ath9k_hw_process_ini() to
write an array of phy registers through REG_WRITE_ARRAY(),
but we already call REG_WRITE_ARRAY() multiple times
on the same caller so just remove this pointless wrapper.
We'll eventually just move the ath9k_hw_process_ini()
caller as an callback to abstract away between different
hardware families.
Although this change is subtle I should note that this
does change the delay pattern on writing the next series
of registers. REG_WRITE_ARRAY() uses a counter for each
register write and does a udelay(1) every 64 writes. By
removing this call it means that the counter is processed
for all the iniBB_RfGain registers and is incremented
on ath9k_hw_process_ini(), before this the after the call
ath9k_hw_write_regs() was made the register counter was
kept at the same index number prior to the call.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 does not have a reset control for AHB.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not a stable code fix as this register is not used anywhere.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9300 will be the first device supported of the AR9003
family. AR9300 1.0 hardware exists but it is not going to
be sold anywhere so we completely skip its support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k supports the AR5008, AR9001 and AR9002 family of Atheros
chipsets, all 802.11n. The new breed of 802.11n chips, the
AR9003 family will be supported as well soon. To help with its
support we're going to add a few callbacks for hardware routines
which differ considerably instead of adding branch checks for
the revision at runtime.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Davinci platforms apparently need more time in-between helper firmware
blocks. Even though this is an increased delay, we only take this hit
once at initialization time.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consolidate a bunch of C&P code that waits for the firmware to be ready.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation for new rtl818x devices, move the existing rtl818x configuration
into the rtl818x directory.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251 is embedded chip that can be connected using SDIO bus, and is not
an actual SDIO card. For this reason there is a need to pass some board
specific data, like 'EEPROM is attached' flag or power control callback.
However currently there is no way to pass this data through SDIO subsystem,
so this patch registers dummy platform_device to allow that, until we
have a better solution to this.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug which was just recently introduced by
("p54pci: prevent stuck rx-ring on slow system").
make M=drivers/net/wireless/p54 C=2 CF=-D__CHECK_ENDIAN__
CHECK drivers/net/wireless/p54/p54pci.c
drivers/net/wireless/p54/p54pci.c:143:11: warning: cast to restricted __le32
CC [M] drivers/net/wireless/p54/p54pci.o
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800pci used the callback write_tx_desc to write the tx descriptor but
also to update the txwi which is part of the dma mapped skb. Since the
memory was already DMA mapped _before_ the call to write_tx_desc the
device didn't get the txwi data at all or only sporadically.
The call order is basically as follows (from rt2x00queue.c):
1) write_tx_data
2) rt2x00queue_map_txskb
3) write_tx_desc
Hence, we shouldn't touch the skb in write_tx_desc anymore.
To fix this issue create a new rt2800pci_write_tx_data callback and use it
for updating the txwi _before_ the memory gets DMA mapped.
The tx descriptor is still written (as before) in write_tx_desc.
This patch allows basic TX on an rt305x soc device but I'm pretty sure
that it will fix pci based cards as well. I can associate just fine with
an AP now but I wasn't able to get a wpa secured connection working yet.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend the write_tx_data callback with a txdesc parameter to allow
access to the tx desciptor while preparing the tx data.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some wl1251 hardware configurations (like in WG7210 module) have
EEPROM attached where NVS data is kept, which includes MAC address.
In such configurations, let's read default MAC address from EEPROM,
instead of using random one.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the following 5 entries to the usbid device table:
* Netgear WNA1000
* Proxim ORiNOCO Dual Band 802.11n USB Adapter
* 3Com Dual Band 802.11n USB Adapter
* H3C Dual Band 802.11n USB Adapter
* WNC Generic 11n USB dongle
CC: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If EEPROM is used, NVS data is now loaded but ignored.
Stop loading it to avoid need of dummy NVS file for modules with EEPROM.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ath9k-htc register out path, ath9k-htc will pass skb->data into
usb hcd and usb hcd will do dma mapping and unmapping to the buffer
pointed by skb->data, so we should pass a cache-line aligned address.
This patch replace __dev_alloc_skb with alloc_skb to make skb->data
pointed to a cacheline aligned address simply since ath9k-htc does not
skb_push on the skb and pass it to mac80211, also use kfree_skb to free
the skb allocated by alloc_skb(we can use kfree_skb safely in hardirq
context since skb->destructor is NULL always in the path).
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ath9k-htc register in path, ath9k-htc will pass skb->data into
usb hcd and usb hcd will do dma mapping and unmapping to the buffer
pointed by skb->data, so we should pass a cache-line aligned address.
This patch replace __dev_alloc_skb with alloc_skb to make skb->data
pointed to a cacheline aligned address simply since ath9k-htc does not
skb_push on the skb and pass it to mac80211, also use kfree_skb to free
the skb allocated by alloc_skb(we can use kfree_skb safely in hardirq
context since skb->destructor is NULL always in the path).
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ath9k_hif_usb_alloc_rx_urbs, ath9k-htc will pass skb->data into
usb hcd and usb hcd will do dma mapping and unmapping to the buffer
pointed by skb->data, so we should pass a cache-line aligned address.
This patch replace __dev_alloc_skb with alloc_skb to make skb->data
pointed to a cacheline aligned address simply since ath9k-htc does not
skb_push on the skb and pass it to mac80211, also use kfree_skb to free
the skbs allocated by alloc_skb(we can use kfree_skb safely in hardirq
context since skb->destructor is NULL always in the path).
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We get RXORN interrupts when all receive buffers are full. This is not
necessarily a fatal situation. It can also happen when the bus is busy or the
CPU is not fast enough to process all frames.
Older chipsets apparently need a reset to come out of this situration, but on
newer chips we can treat RXORN like RX, as going thru a full reset does more
harm than good, there.
The exact chip revisions which need a reset are unknown - this guess
AR5K_SREV_AR5212 ("venice") is copied from the HAL.
Inspired by openwrt 413-rxorn.patch:
"treat rxorn like rx, reset after rxorn seems to do more harm than good"
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a confusion in the usage of the bits AR5K_STA_ID1_ACKCTS_6MB and
AR5K_STA_ID1_BASE_RATE_11B. If they are set (1), we will get lower bitrates for
ACK and CTS. Therefore ath5k_hw_set_ack_bitrate_high(ah, false) actually
resulted in high bitrates, which i think is what we want anyways. Cleared the
confusion and added some documentation.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add RT3390 specific register initializations to rt2x00, based on the latest
Ralink rt3390 vendor driver.
Untested as I don't actually own an RT3390 based device, but given experiences
on rt3070/rt3071 very hopeful that this will actually work..
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add RT3090 specific register initializations to rt2x00, based on the latest
Ralink rt3090 vendor driver.
Untested as I don't actually own an RT3090 based device, but given experiences
on rt3070/rt3071 very hopeful that this will actually work..
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add RT3071 specific register initializations to rt2x00, based on the latest
Ralink rt3070 vendor driver.
With this patch my RT3071 based devices start showing a sign of life.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00 had preliminary support for RT3070 based devices, but the support was
incomplete.
Update the RT3070 register initialization to be similar to the latest Ralink
vendor driver.
With this patch my rt3070 based devices start showing a sign of life.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Align the rt2800 register initializations with the latest versions of the
Ralink vendor driver.
This patch is also preparation for the addition of support for RT3070 /
RT3071 / RT3090 / RT3390 based devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2800 version constants are inconsistent, and the version number don't
mean a lot of things anyway. Refactor the constants to have some more
meaningful names, and introduce and use some new helpers to check these
chipset revisions. At the same time rename to revision, as they are more
revision numbers rather than version numbers.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only include definitions for RT chipsets that are also used inside the
Ralink vendor drivers.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Definitions taken from the latest rt2860 / rt2870 / rt3070 / rt3090 Ralink
vendor drivers.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that the distinction between RF channel switch method is solely based
on the RF chipset that is used.
Refactor the channel switch decision to just take the RF chipset into account,
thereby greatly simplifying the check.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an old problem, which - under certain
circumstances - could cause the device to become
unresponsive.
most of p54pci's rx-ring management is implemented in just
two distinct standalone functions. p54p_check_rx_ring takes
care of processing incoming data, while p54p_refill_rx_ring
tries to replenish all depleted communication buffers.
This has always worked fine on my fast machine, but
now I know there is a hidden race...
The most likely candidate here is ring_control->device_idx.
Quintin Pitts had already analyzed the culprit and posted
a patch back in Oct 2009. But sadly, no one's picked up on this.
( https://patchwork.kernel.org/patch/53079/ [2 & 3] ).
This patch does the same way, except that it also prioritize
rx data processing, simply because tx routines *can* wait.
Reported-by: Sean Young <sean@mess.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=11386
Reported-by: Quintin Pitts <geek4linux@gmail.com>
Signed-off-by: Quintin Pitts <geek4linux@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We used to free all the Tx queues memory when interface is brought
down and reallocate them again in interface up. This requires
order-4 allocation for txq->cmd[]. In situations like s2ram, this
usually leads to allocation failure in the memory subsystem. The
patch fixed this problem by allocating the Tx queues memory only at
the first time. Later iwl_down/iwl_up only initialize but don't
free and reallocate them. The memory is freed at the device removal
time. BTW, we have already done this for the Rx queue.
This fixed bug https://bugzilla.kernel.org/show_bug.cgi?id=15551
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Check return code on iwl_send_cmd_pdu() to get rid of compiler warning.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Fixes:
CC [M] drivers/net/wireless/iwlwifi/iwl-agn-rs.o
drivers/net/wireless/iwlwifi/iwl-agn-rs.c: In function ‘rs_get_rate’:
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:2419: warning: unused variable ‘priv’
CC [M] drivers/net/wireless/iwlwifi/iwl-sta.o
drivers/net/wireless/iwlwifi/iwl-sta.c: In function ‘iwl_send_add_sta’:
drivers/net/wireless/iwlwifi/iwl-sta.c:197: warning: unused variable ‘sta_id’
drivers/net/wireless/iwlwifi/iwl-3945.c: In function ‘iwl3945_rx_reply_rx’:
drivers/net/wireless/iwlwifi/iwl-3945.c:601: warning: unused variable ‘rx_stats_noise_diff’
drivers/net/wireless/iwlwifi/iwl-3945.c:600: warning: unused variable ‘rx_stats_sig_avg’
drivers/net/wireless/iwlwifi/iwl-3945-rs.c: In function ‘rs_get_rate’:
drivers/net/wireless/iwlwifi/iwl-3945-rs.c:650: warning: unused variable ‘priv’
Reported-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
REPLY_TX_LINK_QUALITY_CMD was used by 4965, 5000 series and up
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Update to include additional tx command response status for "_agn"
devices.
The following status indicate the transmission was postponed:
TX_STATUS_POSTPONE_DELAY
TX_STATUS_POSTPONE_FEW_BYTES
TX_STATUS_POSTPONE_BT_PRIO
TX_STATUS_POSTPONE_QUIET_PERIOD
TX_STATUS_POSTPONE_CALC_TTAK
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When sys assert happen, driver will dump the error table information
provided by uCode. There are more information available but is not being
display by the driver; adding program counter and last host command the
to log to help uCode debugging.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The last_phy_res[100] variable is used in an odd
way. The first byte of it is used as a flag, and
the rest as the data. Thus, the array need only
be 61 bytes, since it is just the flag and a
struct iwl_rx_phy_res (which is 60 bytes).
Clean this up by splitting the variable into two:
last_phy_res and last_phy_res_valid, using correct
types for both (struct and bool). While doing all
this also move the variables to the _agn part of
the hw-specific union since they only apply to
A-MPDUs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
lq->sta_id cannot be invalid here since this
function will only be called after the station
has been added properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Simplify the WEP group key check by checking the
sta pointer instead of the sta_id we calculate
with it; also clean up the comment formatting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Default WEP keys and regular keys are not allocated
from the same space in the firmware, so we shouldn't
use the same bits to indicate in use.
For default WEP keys, however, mac80211 won't allow
using the same key index twice, so the check is not
necessary at all -- add/remove are perfectly nested
due to those checks.
Other keys are allocated in the device in a global
array that only has a certain number of slots, so
for that we need to keep the allocation bitmap; but
the 802.11 key index isn't relevant there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The firmware clears default WEP keys on
transitions to !associated, so we need
to restore them just like stations. This
is rather implicit as part of sending a
station right now, which is odd. Make it
explicit instead and only for agn since
3945 doesn't use hw crypto for WEP.
Due to that, iwl_send_static_wepkey_cmd
is now only used in iwl-sta.c and can be
static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Size of event log is determined by uCode which is different per NICs.
Set the maximum event log size per device to better match uCode
configuration.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The current algorithm will sometimes "detect" that
more chains are enabled than are really present in
the device because, for unknown reasons, the ucode
sends up all-zeroes signal values.
The simplest way of solving this is to restrict the
active chains mask to the chains we know are really
present on the device.
This fixes a bug with some devices where, since sometimes
more chains are enabled than really present, the system would hang.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This patch will add support for connection quality monitoring by configuring
rssi triggers to the firmware, and enabling the firmware rssi trigger
functionality.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow the wl1271 go to ELP mode also in idle. This will reduce current
consumption remarkably in idle mode (~12mA -> ~0.2mA)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 sends RTS threshold configuration request even if the wl1271 interface
state is WL1271_STATE_OFF. This leads to failures during pm tests.
This patch leaves the configuration function, if the interface is
going down.
Signed-off-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 sends configuration requests even if the wl1271 interface
state is WL1271_STATE_OFF. This creates warnings from mac80211.
This patch leaves the configuration functions, if the interface is
going down.
Signed-off-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes some memory leaks occurring during driver init/de-init.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Resolution of a merge conflict upstream accidentally removed a hunk of
"ath5k: IQ calibration for AR5211 is slightly different", so restore it.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 4965, need to check it is valid qos frame before free, only valid
QoS frame has the tid used to free the packets.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simple pre-scan and scan complete callbacks, this at least shows
to me that mac80211 will issue two scans at the same time on the
same wiphy.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We check the bounds on pdadc once when correcting for
negative curves but not when we later copy values from
from the pdadc_tmp array, leading to a potential overrun.
Although we shouldn't hit this case in practice, let's
be consistent.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As pointed out by Benoit Papillault, there is a potential
race condition between the host and the hardware in reading
the next link in the transmit descriptor list:
cpu0 hw
tx for buf completed
raise tx_ok interrupt
process buf
buf->ds_link = 0
read buf->ds_link
This change checks txdp before processing a descriptor
(if there are any subsequent descriptors) to see if
hardware moved on. We'll then process this descriptor on
the next tasklet.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Review spotted a couple of strange invocations to
ieee80211_wake_queues that could potentially cause problems:
- queues are awakened in the calibration tasklet before
phy calibration, and then again after calibration
- queues are awakened inside reset when we're trying to
drain the ath5k transmit queues, and again after
reset is completed (in callers to ath5k_reset_wake).
In both cases the first wake is unnecessary, so remove it.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These channels aren't selectable anyway, but our calculations
for 2.5 mhz frequencies are incorrect. The value is supposed to
be:
(frequency - reference) * (10/25)
i.e., divide by 2.5, but we were instead doing:
(10 * frequency - reference) / 25.
Additionally, the check for (frequency % 5 == 2) had an extra
subtraction that wasn't in madwifi HAL.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2872 needs the same rf register setup as rt3070 and rt3090, hence
use rt2800_config_channel_rt3x instead of rt2800_config_channel_rt2x.
This change allows me to actually switch channels and hence scan all
configured channels on the RT305x SoC platform (which uses a rt2872)
here.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't modify ah->iniModes, it's supposed to be constant. Instead, apply
the fixup when the data is written to the registers.
Change ath9k_hw_init_eeprom_fix() to only determine whether the fixup is
needed.
This allows similteneous support for AR9220 cards that need AR_AN_TOP2
fixup (such as Ubiquiti SR71-12) and those that don't need it (D-Link
DWA-552 rev A2).
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Messages that are generated by the HTC layer
don't have any TX callback endpoints assigned to them.
Consequently, the allocated SKBs are never freed.
Fix this issue by handling this case in the HTC layer
itself.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hif_usb_regout_cb() frees the given URB, which is
borked by design. Use an anchor to simplify URB
management.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The maximum number of packets in a single buffer in
stream mode is 10. The driver currently uses 8 - which
caused stack corruption, in the absence of any kind
of OOB checking.
Fixing this to the correct value of 10 fixes the module
unload issue.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX URBs are automatically freed when the reference
count drops to zero - this currently doesn't happen when
usb_kill_anchored_urbs() is called during unload.
Fix this by dropping the reference count by one during
initial submission.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a spin lock to prevent concurrent access
to variables dealing with RX stream mode handling.
Currently, no protection is implemented - which
causes problems in RX.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the powersave issues on rt2500usb have been tackled, powersave
can be enabled by default again.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for a modified newer version of AR9285
chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Better use the macro for consistency, the content is the same anyway.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an Adaptive Noise Imunity (ANI) implementation for ath5k. I have looked
at both ath9k and HAL sources (they are nearly the same), and even though i
have implemented some things differently, the basic algorithm is practically
the same, for now. I hope that this can serve as a clean start to improve the
algorithm later.
This also adds a possibility to manually control ANI settings, right now only
thru a debugfs file:
* set lowest sensitivity (=highest noise immunity):
echo sens-low > /sys/kernel/debug/ath5k/phy0/ani
* set highest sensitivity (=lowest noise immunity):
echo sens-high > /sys/kernel/debug/ath5k/phy0/ani
* automatically control immunity (default):
echo ani-on > /sys/kernel/debug/ath5k/phy0/ani
* to see the parameters in use and watch them change:
cat /sys/kernel/debug/ath5k/phy0/ani
Manually setting sensitivity will turn the automatic control off. You can also
control each of the five immunity parameters (noise immunity, spur immunity,
firstep, ofdm weak signal detection, cck weak signal detection) manually thru
the debugfs file.
This is tested on AR5414 and nearly doubles the thruput in a noisy 2GHz band.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies tx-queue flushing to correspond with tx-path - i.e.
also frames for which no ack was requested are forwarded to the mac80211
for disposal.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ERROR print from psm-entry-fail scenario, instead use an INFO print.
Also, add INFO print to the beacon-loss scenario.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase the fixed listen-interval max value configured to the mac80211 on
driver init. This value will allow a larger value to be configured to the
AP, which means the AP will buffer our frames longer.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure meaningful rates to be used with the templates. For control frames,
use the determined basic rates (currently the lowest rate for the band) and
for data-frames (null-funcs) let the firmware use the current rate policy to
determine the rate.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the mac80211 is not telling a hardware rate controlled driver a
rate to use for association frames etc. So to be safe, use the lowest rate
of each band for communication.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware does not like the host configuring the keep-alive after it has
been once configured after a join-operation. Instead, it will complain about
invalid parameters, which do not break functionality, but do not look nice
in the syslog either.
This patch prevents the complaints by only configuring the keep-alive once
for an association, after the first time join is performed with the correct
bssid.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The command header was missing in the wl1271_cmd_disconnect structure. It
was working fine by sheer luck, because the parameters are not critical and
because our wl1271_cmd_send() function was overwriting the rx_config_options
with the actual header.
This patch adds the header to the command structure.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Our SPI driver is called "wl1271_spi" in the driver information structure.
Let's use the same for SDIO so that things are aligned.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For USB devices, this check is invalid.
Remove the check so that new product IDs can be added.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be used to store the bus types ( AHB/PCI/USB ).
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commits 8e6f5aa250 and
db1a052b73 accidentally introduced
compile errors that happens when ath9k debug is not enabled.
This patch fixes the declaration of the inline stubs to resolve this.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ah->mask_reg was used to hold different data throughout the driver.
ath9k_hw_init_interrupt_masks() used it to save the value written to
AR_IMR. ath9k_hw_set_interrupts() used it to hold the interrupt mask as
defined in enum ath9k_int. Those masks differ in many bits.
Use ah->imask instead of ah->mask_reg in ath9k_hw_set_interrupts() and
ath9k_hw_updatetxtriglevel(). That's what the code was meant to do.
ah->imask is initialized in ath9k_start(), so we don't need to
initialize it from ah->mask_reg.
Once it's done, ah->mask_reg becomes write-only, so it's replaced with a
local variable in ath9k_hw_init_interrupt_masks().
Signed-off-by: Pavel Roskin <proski@gnu.org>
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ah variable in the functions that didn't have it and used sc->imask.
Replace sc->sc_ah with ah in those functions.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Symbols starting with "ATH9K_INT" are also used for interrupt mask.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a patch to files in ath/ar9170 that fixes a set of warnings
found by checkpatch.pl tool. A line over 80 characters, a few empty
spaces before tab and a few empty characters before a new line.
Signed-off-by: Luis de Bethencourt <luisbg@ubuntu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to wake up the device automatically for receiving beacons,
and is required for proper powersave handling.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to wake up the device automatically for receiving beacons,
and is required for proper powersave handling.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In all drivers ensure that auto wakeup is disabled before waking up the device.
This is needed to prevent connection stability issues and problems in waking up
the device.
Based upon a patch from Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When operating in 1-bit mode, SDAT1 is used as dedicated interrupt line.
However, the 8686 will only drive this line when the ECSI bit is set in
the CCCR_IF register.
Thanks to Alagu Sankar for pointing me in the right direction.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alagu Sankar <alagusankar@embwise.com>
Cc: Volker Ernst <volker.ernst@txtr.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a patch to the ath/regd.c file that fixes two code
readability issues. A space between to separate two defines
and the indentation inside the ath_redg_is_eeprom_valid
function.
Signed-off-by: Luis de Bethencourt <luisbg@ubuntu.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a patch to the ath/hw.c file that fixes up a warning about
macros found by the checkpatch.pl tool, that said that complex values
should be enclosed in parenthesis.
Signed-off-by: Luis de Bethencourt <luisbg@ubuntu.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the enable_radio being uninitialized, ath_radio_enable() might be
called twice, which can leave some hardware in an undefined state.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville