The help text should be indented by at least two spaces after the
'help' separator. This is both good practice and the media_build system
for building media drivers makes this assumption.
Fix this for the atomisp/i2c/Kconfig and fix the atomisp/pci/Kconfig
that didn't align the help separator with the preceding keywords.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
driver_attribute are not supposed to change at runtime.
Functions driver_create_file/driver_remove_file are working with
const driver_attribute. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Kfree on NULL pointer is a no-op and therefore checking is redundant.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure these values are set to avoid 'uninitialized variable'
warnings. Hasn't happened yet, but better safe than sorry.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The help text should be indented by at least two spaces after the
'help' separator. This is both good practice and the media_build system
for building media drivers makes this assumption.
I went through all Kconfigs under drivers/media and fixed any bad help
sections. This makes it conform to the common practice and should fix
problems with 'make menuconfig' when using media_build. This is due to
a "WARNING" message that media_build can insert in the Kconfig and that
assumes the help text is indented by at least two spaces. If not, then the
Kconfig becomes invalid and 'make menuconfig' fails.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Thomas Kaiser <linux-dvb@kaiser-linux.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In the distant past the adv7604 driver used private controls. In order
to access them the v4l-subdevX nodes were needed. Later the is_private
tag was removed in the adv7604 driver and the need for v4l-subdevX
device nodes disappeared.
Remove the creation of those device nodes from this driver.
Note: the cobalt card is only used inside Cisco and we never actually
used the v4l-subdevX nodes for anything. So this API change can be done
safely without breaking anything.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
max_width and max_height are swap with step_width and step_height.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Delete an error message for a failed memory allocation
in init_vpbe_layer();
- Replace the specification of data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding
size determination a bit safer according to the Linux coding style
convention;
- media: DaVinci-VPBE-Display: Improve a size determination in two
functions
- Adjust 12 checks for null pointers
Those issues were pointed by checkpatch.pl and Coccinelle.
[mchehab@s-opensource.com: fold three cleanup patches into one]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script "checkpatch.pl" pointed information out like the following.
ERROR: do not use assignment in if condition
Thus fix the affected source code place.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script "checkpatch.pl" pointed information out like the following.
ERROR: do not use assignment in if condition
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate the array buf on the stack, instead make it static.
Makes the object code smaller by over 240 bytes:
Before:
text data bss dec hex filename
21689 22992 416 45097 b029 cx23885-cards.o
After:
text data bss dec hex filename
21348 23088 416 44852 af34 cx23885-cards.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate the arrays res_x and resy_y on the stack, instead make them
static const. Makes the object code smaller by over 160 bytes:
Before:
text data bss dec hex filename
10509 2800 64 13373 343d ov9640.o
After:
text data bss dec hex filename
10184 2960 64 13208 3398 ov9640.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The error handling paths all end up with retval being non-zero,
so the check for retval being zero is always false and hence
is redundant. Remove it.
Detected by CoverityScan CID#1309479 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate the array syds on the stack, instead make it static const.
Makes the object code smaller by over 280 bytes:
Before:
text data bss dec hex filename
81451 12784 704 94939 172db cx25840-core.o
text data bss dec hex filename
81070 12880 704 94654 171be cx25840-core.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use ARRAY_SIZE macro, rather than explicitly coding some variant of it
yourself.
Found with: find -type f -name "*.c" -o -name "*.h" | xargs perl -p -i -e
's/\bsizeof\s*\(\s*(\w+)\s*\)\s*\ /\s*sizeof\s*\(\s*\1\s*\[\s*0\s*\]\s*\)
/ARRAY_SIZE(\1)/g' and manual check/verification.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixes one sparse warning:
mxl5xx.c:46:1: warning: symbol 'mxllist' was not declared. Should it be static?
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate the array rc_nec_tab on the stack, instead make it
static const. Makes the object code smaller by over 620 bytes:
Before:
text data bss dec hex filename
49511 17040 64 66615 10437 rtl28xxu.o
After:
text data bss dec hex filename
48825 17104 64 65993 101c9 rtl28xxu.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used in a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used in a copy operation.
Done using Coccinelle.
@match disable optional_qualifier@
identifier s;
@@
static struct i2c_client s = {...};
@ref@
position p;
identifier match.s;
@@
s@p
@good1@
position ref.p;
identifier match.s,f,c;
expression e;
@@
(
e = s@p
|
e = s@p.f
|
c(...,s@p.f,...)
|
c(...,s@p,...)
)
@bad depends on !good1@
position ref.p;
identifier match.s;
@@
s@p
@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct i2c_client s;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* Return directly after a call of the function "kzalloc" failed
at the beginning.
* Move a bit of exception handling code into an if branch.
* Delete jump targets which became unnecessary with this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written !…
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
[mchehab@s-opensoure.com: merge similar patches into one]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
The variables will be set to an appropriate value before usage.
Thus omit the explicit initialisation at the beginning.
[mchehab@s-opensource.com: fold similar patches into one]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
[mchehab@s-opensource.com: fold several similar patches into one]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add CEC support for the tc358743 HDMI-CSI bridge.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add an entry for the CEC GPIO driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a simple HDMI CEC GPIO driver that sits on top of the cec-pin framework.
While I have heard of SoCs that use the GPIO pin for CEC (apparently an
early RockChip SoC used that), the main use-case of this driver is to
function as a debugging tool.
By connecting the CEC line to a GPIO pin on a Raspberry Pi 3 for example
it turns it into a CEC debugger and protocol analyzer.
With 'cec-ctl --monitor-pin' the CEC traffic can be analyzed.
But of course it can also be used with any hardware project where the
HDMI CEC line is hooked up to a pull-up gpio line.
In addition this has (optional) support for tracing HPD changes if the
HPD is connected to a GPIO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Document the bindings for the cec-gpio module for hardware where the
CEC line and optionally the HPD line are connected to GPIO lines.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for two new low-level events: PIN_HPD_LOW and PIN_HPD_HIGH.
This is specifically meant for use with the upcoming cec-gpio driver
and makes it possible to trace when the HPD pin changes. Some HDMI
sinks do strange things with the HPD and this makes it easy to debug
this.
Note that this also moves the initialization of a devnode mutex and
list to the allocate_adapter function: if the HPD is high, then as
soon as the HPD interrupt is created an interrupt occurs and
cec_queue_pin_hpd_event() is called which requires that the devnode
mutex and list are initialized.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CEC_TX_STATUS_ERROR can be used if the HW cannot tell LOST_ARB and
LOW_DRIVE apart, or when some other error occurs. It is not a
replacement for NACK.
So the hardware must be able to tell the difference between OK, NACK and
'something else'.
Clarify the documentation (both public and kernel API) on this point.
Also fix two small typos (this messages -> this message).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The documentation talked about INITIAL_VALUE when the actual define is
INITIAL_STATE.
Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use ktime_to_ns/ns_to_ktime. This makes it possible to work with older kernels
and the media_build compatibility system.
For the mainline kernel these functions are NOPs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Running CEC 1.4 compliance test we get the following error on test
11.1.6.2: "ERROR: The DUT did not broadcast a
<Report Physical Address> message to the unregistered device."
Fix this by letting GIVE_PHYSICAL_ADDR message respond to unregistered
device. Also, GIVE_DEVICE_VENDOR_ID and GIVE_FEATURES fall in the
same category so, respond also to these messages.
With this fix we pass CEC 1.4 official compliance.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The s5p-cec driver returned CEC_TX_STATUS_ERROR for the NACK condition.
Some digging into the datasheet uncovered the S5P_CEC_TX_STAT1 register where
bit 0 indicates if the transmit was nacked or not.
Use this to return the correct CEC_TX_STATUS_NACK status to userspace.
This was the only driver that couldn't tell a NACK from another error, and
that was very unusual. And a potential problem for applications as well.
Tested with my Odroid-U3.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: <stable@vger.kernel.org> # for v4.12 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ret variable can be returned uninitialized in the
imx_media_create_pad_vdev_lists() function is imxmd->num_vdevs is zero.
Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The function vfe_set_selection is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
warning: symbol 'vfe_set_selection' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit 29d2fef8be ("usb: catch attempts to submit urbs
with a vmalloc'd transfer buffer"), the AverMedia AverTV DVB-T
USB 2.0 (a800) fails to probe.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We get a link error when V4L2_FLASH_LED_CLASS=m and AS3645A is built-in:
drivers/leds/leds-as3645a.o: In function `as3645a_v4l2_setup':
leds-as3645a.c:(.text+0x258): undefined reference to `v4l2_flash_init'
leds-as3645a.c:(.text+0x284): undefined reference to `v4l2_flash_indicator_init'
leds-as3645a.c:(.text+0x2a4): undefined reference to `v4l2_flash_release'
drivers/leds/leds-as3645a.o: In function `as3645a_remove':
leds-as3645a.c:(.text+0x784): undefined reference to `v4l2_flash_release'
This adds the same Kconfig dependency that the other V4L2 flash
drivers in drivers/leds use, to avoid that broken configuration.
Fixes: a56ba8fbcb ("media: leds: as3645a: Add LED flash class driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Those two ioctls were never used within the Kernel. Still, there
used to have compat32 code there (and an if #0 block at the core).
Get rid of them.
Fixes: 286fe1ca3f ("media: dmx.h: get rid of DMX_GET_CAPS")
Fixes: 13adefbe9e ("media: dmx.h: get rid of DMX_SET_SOURCE")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This reverts commit d2180e0cf7.
The commit was flawed in that if the device_node pointers are different,
then in fact a different device is present and the device node could be
different in ways other than full_name.
As Frank Rowand explained:
"When an overlay (1) is removed, all uses and references to the nodes and
properties in that overlay are no longer valid. Any driver that uses any
information from the overlay _must_ stop using any data from the overlay.
Any driver that is bound to a new node in the overlay _must_ unbind. Any
driver that became bound to a pre-existing node that was modified by the
overlay (became bound after the overlay was applied) _must_ adjust itself
to account for any changes to that node when the overlay is removed. One
way to do this is to unbind when notified that the overlay is about to
be removed, then to re-bind after the overlay is completely removed.
If an overlay (2) is subsequently applied, a node with the same
full_name as from overlay (1) may exist. There is no guarantee
that overlay (1) and overlay (2) are the same overlay, even if
that node has the same full_name in both cases."
Also, there's not sufficient overlay support in mainline to actually
remove and re-apply an overlay to hit this condition as overlays can
only be applied from in kernel APIs.
Fixes: d2180e0cf7 ("[media] v4l: async: make v4l2 coexist with devicetree nodes in a dt overlay")
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Javi Merino <javi.merino@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The calloc function returns either a null pointer or a pointer to the
allocated space. Add the second case that is missed.
Fixes: da22013f7d ("atomisp: remove indirection from sh_css_malloc")
Signed-off-by: Sergei A. Trusov <sergei.a.trusov@ya.ru>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This reverts commit 5be2b76a9c.
Only when the lirc device is freed, should we drop our reference to
rc_dev, else we the rc_dev is freed to early. If userspace has
a file descriptor open during unplug, it goes bang.
==================================================================
BUG: KASAN: use-after-free in __lock_acquire+0x7bb/0x1e10
Read of size 8 at addr ffff8801d7d61ed0 by task ir-rec/2609
-snip-
mutex_lock_nested+0x1b/0x20
? mutex_lock_nested+0x1b/0x20
rc_close.part.6+0x20/0x60 [rc_core]
rc_close+0x13/0x20 [rc_core]
lirc_dev_fop_close+0x62/0xd0 [lirc_dev]
__fput+0x236/0x410
? fput+0xb0/0xb0
? do_raw_spin_trylock+0x110/0x110
? set_rq_offline.part.70+0xa0/0xa0
____fput+0xe/0x10
task_work_run+0x116/0x180
? task_work_cancel+0x170/0x170
? _raw_spin_unlock+0x27/0x40
? switch_task_namespaces+0x5f/0x90
do_exit+0x68b/0xe80
Cc: stable@vger.kernel.org # For Kernel 4.13
Fixes: 5be2b76a9c ("[media] lirc_dev: remove superfluous get/put_device() calls")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Avoid this warning:
/devel/v4l/docs/Documentation/media/v4l-drivers/qcom_camss.rst:: WARNING: document isn't included in any toctree
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adjust dvb ca.h, dmx.h and frontend.h in order to make
checkpatch happier. Now, it only complains about the typedefs,
and those are there just to provide backward userspace
compatibility.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There's a chapter for the legacy APIs. Move the frontend DVBv3
API to it, and update the chapter's introduction accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adjust the table to be better displayed on PDF output.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There appears to be an issue in using \small in certain cases on Sphinx
1.4 and 1.5. Other format documents don't use \small either, remove it
from here as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
[mchehab@s-opensource.com: kept tabularcolumns - readjusted - and
add a few blank lines for it to display better]
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans Verkuil