Apart from the usual stuff, the debugfs code is currently also used for
one non-obvious side effect. It attempts to check whether the chip's
registers are still set to an expected value, and if not, re-initializes
them. It seems that the driver has "always" done so.
The code, however, also checks the INTF register which normally
indicates which pins have caused the recent interrupt. That's a volatile
register, and the datasheet says that writes are ignored in there.
When I'm just cat-ing /sys/kernel/debug/gpio with no SPI traffic and no
nosie on the GPIO lines, I'm not getting any warnings. Once I actually
use these GPIOs and cat that file in parallel, I always seem to get a:
mcp23s08 spi1.1: restoring reg 0x07 from 0x0000 to 0xffff (power-loss?)
This might be a sign that I should not leave my unused inputs floating,
but the code should not be checking a volatile register, anyway. Let's
simply skip this last item in the iteration. I was also considering
removing this enitre re-initialization because it's non-obvious, but the
code survived various refactorings already and has sign-offs by people
who know more than I do, so let's leave it as-is. For now :).
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mcp23s08 series device can be configured for wired and interrupts
using an external pull-up and open drain output via the IOCON_ODR bit.
And "drive-open-drain" property to enable this.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
one_regmap_config is always null if mcp type is MCP_TYPE_S18.
Remove the null check so that the mcp23s18 will probe.
Fixes: 1781af563a ("pinctrl: mcp23s08: spi: Fix duplicate pinctrl debugfs entries")
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a bit more involved because the pinctrl core so far always
assumed that one device (with a unique dev_name) only contains a single
pinctrl thing. This is not true for the mcp23s08 driver for chips
connected over SPI. They have a "logical address" which means that
several chips can share one physical CS signal.
A downside of this patch are some possibly ugly names for the debugfs
entries, such as "spi1.1-mcp23xxx-pinctrl.2", etc.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When several devices are sharing one hardware SPI CS, there is no visual
clue in `lsgpio` or in /sys/kernel/debug/gpio about which one is which
one. Stuff depends on the enumeration order, and therefore lower chip
addresses always go first, but that's just an implementation detail.
This change includes the device-specific address in the debug output:
gpiochip4: GPIOs 464-479, parent: spi/spi1.1, mcp23s17.2, can sleep:
gpiochip3: GPIOs 480-495, parent: spi/spi1.1, mcp23s17.1, can sleep:
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI version of this chip allows several devices to be present on the
same SPI bus via a local address. If this is in action and if the kernel
has debugfs, however, the code attempts to create duplicate entries for
the regmap's debugfs:
mcp23s08 spi1.1: Failed to create debugfs directory
This patch simply assigns a local name matching the device logical
address to the `struct regmap_config`.
No changes are needed for MCP23S18 because that device does not support
any logical addressing. Similarly, I2C devices do not need any action,
either, because they are already different in their I2C address.
A similar problem is present for the pinctrl debugfs instance, but that
one is not addressed by this patch.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When using mcp23s08 module with gpio-keys, often (50% of boots)
it fails to get irq numbers with message:
"gpio-keys keys: Unable to get irq number for GPIO 0, error -6".
Seems that irqs must be setup before devm_gpiochip_add_data().
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Mastykin <mastichi@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Print a line break together with other data in a single function call.
* Adjust indentation.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Add a jump target so that a call of the function "mutex_unlock" is stored
only twice in this function implementation.
* Replace five calls by goto statements.
* Adjust five condition checks.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into
a menuconfig option. This obviously has the implication of
making the subsystem menu visible in menuconfig. This is
happening because of two things:
- Intel have started to deploy and depend on pin controllers
in a way that is affecting users directly. This happens
on the highly integrated laptop chipsets named after
geographical places: baytrail, broxton, cannonlake,
cedarfork, cherryview, denverton, geminilake, lewisburg,
merrifield, sunrisepoint... It started a while back and
now it is ever more evident that this is crucial
infrastructure for x86 laptops and not an embedded
obscurity anymore. Users need to be aware.
- Pin control expanders on I2C and SPI that are
arch-agnostic. Currently Semtech SX150X and Microchip
MCP28x08 but more are expected. Users will have to be
able to configure these in directly for their set-up.
- Just go and select GPIOLIB now that we made sure that
GPIOLIB is a very vanilla subsystem. Do not depend on
it, if we need it, select it.
- Exposing the pin control subsystem in menuconfig uncovered
a bunch of obscure bugs that are now hopefully fixed,
all more or less pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and
GPIO.
- New support for clock skew/delay generic DT bindings
and generic pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying.
-----BEGIN PGP SIGNATURE-----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=kj/b
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.15 kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into a
menuconfig option. This obviously has the implication of making the
subsystem menu visible in menuconfig. This is happening because of
two things:
(a) Intel have started to deploy and depend on pin controllers in
a way that is affecting users directly. This happens on the
highly integrated laptop chipsets named after geographical
places: baytrail, broxton, cannonlake, cedarfork, cherryview,
denverton, geminilake, lewisburg, merrifield, sunrisepoint...
It started a while back and now it is ever more evident that
this is crucial infrastructure for x86 laptops and not an
embedded obscurity anymore. Users need to be aware.
(b) Pin control expanders on I2C and SPI that are arch-agnostic.
Currently Semtech SX150X and Microchip MCP28x08 but more are
expected. Users will have to be able to configure these in
directly for their set-up.
- Just go and select GPIOLIB now that we made sure that GPIOLIB is a
very vanilla subsystem. Do not depend on it, if we need it, select
it.
- Exposing the pin control subsystem in menuconfig uncovered a bunch
of obscure bugs that are now hopefully fixed, all more or less
pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and GPIO.
- New support for clock skew/delay generic DT bindings and generic
pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying"
* tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits)
pinctrl: gemini: Fix missing pad descriptions
pinctrl: Add some depends on HAS_IOMEM
pinctrl: samsung/s3c24xx: add CONFIG_OF dependency
pinctrl: gemini: Fix GMAC groups
pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support
pinctrl: ti-iodelay: remove redundant unused variable dev
pinctrl: max77620: Use common error handling code in max77620_pinconf_set()
pinctrl: gemini: Implement clock skew/delay config
pinctrl: gemini: Use generic DT parser
pinctrl: Add skew-delay pin config and bindings
pinctrl: armada-37xx: Add edge both type gpio irq support
pinctrl: uniphier: remove eMMC hardware reset pin-mux
pinctrl: rockchip: Add iomux-route switching support for rk3288
pinctrl: intel: Add Intel Cedar Fork PCH pin controller support
pinctrl: intel: Make offset to interrupt status register configurable
pinctrl: sunxi: Enforce the strict mode by default
pinctrl: sunxi: Disable strict mode for old pinctrl drivers
pinctrl: sunxi: Introduce the strict flag
pinctrl: sh-pfc: Save/restore registers for PSCI system suspend
pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description
...
CORE:
- Fix the semantics of raw GPIO to actually be raw. No
inversion semantics as before, but also no open draining,
and allow the raw operations to affect lines used for
interrupts as the caller supposedly knows what they are
doing if they are getting the big hammer.
- Rewrote the __inner_function() notation calls to names that
make more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all
IRQs are mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This
allows us to read several GPIO lines with a single
register read. This has high value for some usecases: it
can be used to create oscilloscopes and signal analyzers
and other things that rely on reading several lines at
exactly the same instant. Also a generally nice
optimization. This uses the new assign_bit() macro from
the bitops lib that was ACKed by Andrew Morton and
is implemented for two drivers, one of them being the
generic MMIO driver so everyone using that will be able
to benefit from this.
- Do not allow requests of Open Drain and Open Source
setting of a GPIO line simultaneously. If the hardware
actually supports enabling both at the same time the
electrical result would be disastrous.
- A new interrupt chip core helper. This will be helpful
to deal with "banked" GPIOs, which means GPIO controllers
with several logical blocks of GPIO inside them. This
is several gpiochips per device in the device model, in
contrast to the case when there is a 1-to-1 relationship
between a device and a gpiochip.
NEW DRIVERS:
- Maxim MAX3191x industrial serializer, a very interesting
piece of professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the
recent Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
OTHER IMPROVEMENTS:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the
Broadcom BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal
of dead code etc.
- Explicit comments on fall-through switch() statements.
-----BEGIN PGP SIGNATURE-----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=8Mon
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.15 kernel cycle:
Core:
- Fix the semantics of raw GPIO to actually be raw. No inversion
semantics as before, but also no open draining, and allow the raw
operations to affect lines used for interrupts as the caller
supposedly knows what they are doing if they are getting the big
hammer.
- Rewrote the __inner_function() notation calls to names that make
more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all IRQs are
mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This allows us
to read several GPIO lines with a single register read. This has
high value for some usecases: it can be used to create
oscilloscopes and signal analyzers and other things that rely on
reading several lines at exactly the same instant. Also a generally
nice optimization. This uses the new assign_bit() macro from the
bitops lib that was ACKed by Andrew Morton and is implemented for
two drivers, one of them being the generic MMIO driver so everyone
using that will be able to benefit from this.
- Do not allow requests of Open Drain and Open Source setting of a
GPIO line simultaneously. If the hardware actually supports
enabling both at the same time the electrical result would be
disastrous.
- A new interrupt chip core helper. This will be helpful to deal with
"banked" GPIOs, which means GPIO controllers with several logical
blocks of GPIO inside them. This is several gpiochips per device in
the device model, in contrast to the case when there is a 1-to-1
relationship between a device and a gpiochip.
New drivers:
- Maxim MAX3191x industrial serializer, a very interesting piece of
professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the recent
Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
Other improvements:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the Broadcom
BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal of dead
code etc.
- Explicit comments on fall-through switch() statements"
* tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (65 commits)
gpio: tegra186: Remove tegra186_gpio_lock_class
gpio: rcar: Add r8a77995 (R-Car D3) support
pinctrl: bcm2835: Fix some merge fallout
gpio: Fix undefined lock_dep_class
gpio: Automatically add lockdep keys
gpio: Introduce struct gpio_irq_chip.first
gpio: Disambiguate struct gpio_irq_chip.nested
gpio: Add Tegra186 support
gpio: Export gpiochip_irq_{map,unmap}()
gpio: Implement tighter IRQ chip integration
gpio: Move lock_key into struct gpio_irq_chip
gpio: Move irq_valid_mask into struct gpio_irq_chip
gpio: Move irq_nested into struct gpio_irq_chip
gpio: Move irq_chained_parent to struct gpio_irq_chip
gpio: Move irq_default_type to struct gpio_irq_chip
gpio: Move irq_handler to struct gpio_irq_chip
gpio: Move irqdomain into struct gpio_irq_chip
gpio: Move irqchip into struct gpio_irq_chip
gpio: Introduce struct gpio_irq_chip
pinctrl: armada-37xx: remove unused variable
...
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the required definitions for the mcp23018 which is the i2c
variant of the mcp23s18.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
interrupt handling was broken with conversion to using regmap caching.
cached_gpio value was updated by boolean status instead of gpio reading.
Fixes: 8f38910ba4 ("pinctrl: mcp23s08: switch to regmap caching")
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Dmitry Mastykin <mastichi@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Variable mask and val are not used in the mcp_pinconf_set().
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver supports using mcp23xxx as interrupt controller, so
let's drop all comments stating otherwise.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves irq property handling from spi/i2c specific code into
the generic mcp23s08_probe_one. This is possible because the
device properties are named equally.
As a side-effect this drops support for setting the properties via
pdata, which has no mainline users. If boardcode wants to enable
the chip as interrupt controller it can attach the device properties
instead.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simplify spi pdata handling, so that it uses pdata when available
and falls back to reading device properties otherwise.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simplify i2c pdata handling, so that it uses pdata when available
and falls back to reading device properties otherwise.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Switching to devm_gpiochip_add_data simplifies the driver's
cleanup routine and safes a few loc.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Let's remove a few lines of code by using managed memory for mcp
variable.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
i2c-core and spi-core already assign the irq, so we
can drop the additional call from the mcp driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of using custom caching, this switches to regmap based
caching. Before the conversion the debugfs file used uncached
values, so that it was easily possible to see power-loss related
problems. The new code will check and recover at this place.
The patch will also ensure, that irqs are not cleared by checking
register status in debugfs.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mcp23s08 support configuration of the pullups using the
pinconf framework. This removes the custom pullup configuration
from platform data, which has no upstream users.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mcp23xxx device have configurable 100k pullup resistors. This adds
support for enabling them using pinctrl's pinconf interface.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the mcp23s08 driver from gpio to pinctrl. Actual
pinctrl support for configuration of the pull-up resistors
follows in its own patch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Jan Kundrát