Commit Graph

37 Commits

Author SHA1 Message Date
Wolfram Sang cc40bf9a44 i2c: i2c-mxs: replace platform_driver_probe to support deferred probing
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.

Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-10-10 10:22:29 +02:00
Wolfram Sang 687b81d083 i2c: move OF helpers into the core
I2C of helpers used to live in of_i2c.c but experience (from SPI) shows
that it is much cleaner to have this in the core. This also removes a
circular dependency between the helpers and the core, and so we can
finally register child nodes in the core instead of doing this manually
in each driver. So, fix the drivers and documentation, too.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-08-23 10:22:20 +02:00
Lothar Waßmann 869c6a3ede i2c: mxs: fix broken timing calculation
The timing calculation is rather bogus and gives extremely wrong
results for higher frequencies (on an i.MX28). E.g. instead of 400 kHz
I measured 770 kHz.

Implement a calculation that adheres to the I2C spec and gives exact
results for I2C frequencies from 12.56 kHz to 960 kHz.

Also the bus_free and leadin parameters are programmed according to
the I2C spec for standard and fast mode.

This was tested on a Ka-Ro TX28 module with a DS1339, TSC2007, PCA9554
and SGTL5000 client.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Marek Vasut <marex@denx.de>
[wsa: patch fixes whitespace issue, too]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-08-16 18:09:05 +02:00
Fabio Estevam 63151c539d i2c: mxs: Check the return value from stmp_reset_block()
stmp_reset_block() may fail, so let's check its return value and propagate it in
the case of error.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-08-15 11:59:09 +02:00
Fabio Estevam d6e102f498 i2c: i2c-mxs: Use DMA mode even for small transfers
Recently we have been seing some reports about PIO mode not working properly.

- http://www.spinics.net/lists/linux-i2c/msg11985.html
- http://marc.info/?l=linux-i2c&m=137235593101385&w=2
- https://lkml.org/lkml/2013/6/24/430

Let's use DMA mode even for small transfers.

Without this patch, i2c reads the incorrect sgtl5000 version on a mx28evk when
touchscreen is enabled:

[    5.856270] sgtl5000 0-000a: Device with ID register 0 is not a sgtl5000
[    9.877307] sgtl5000 0-000a: ASoC: failed to probe CODEC -19
[    9.883528] mxs-sgtl5000 sound.12: ASoC: failed to instantiate card -19
[    9.892955] mxs-sgtl5000 sound.12: snd_soc_register_card failed (-19)

Cc: <stable@vger.kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Marek Vasut <marex@denx.de>

[wsa: we have a proper solution for -next, so this non intrusive
solution is OK for now]

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-08-05 10:09:12 +02:00
Fabio Estevam dfda7d8f09 i2c: mxs: Let device core handle pinctrl
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for handling pinctrl.

So remove devm_pinctrl_get_select_default() from the driver.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-06-12 20:39:06 +02:00
Linus Torvalds 38f56f33ca ARM: arm-soc device tree changes, part 2
These are mostly new device tree bindings for existing drivers, as well
 as changes to the device tree source files to add support for those
 devices, and a couple of new boards, most notably Samsung's Exynos5
 based Chromebook.
 
 The changes depend on earlier platform specific updates and touch
 the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIVAwUAUYgjh2CrR//JCVInAQJTvRAAmxaeoI+kQ/pbbRDa/Mnhf+bUmQjvJvx4
 uFGYAAi23Txem2Bx6xrfvOo9//ATYSfRxenoSSOtXQucsnrqD0+837Sj2NbO6AB9
 MSiFDK4usJtGwSUybkSHNLb2QPBr8XTgmyWVE/sHEw2UtrIToC1n3sxFofFm0guT
 ReILKsgK0Wjyq5RntnjWOCHNNp6OGqDGvFXlSJqNA7Z6gR/VZy4o0oXS4Sv3TWgF
 zG7ngSG7/u9FP1IQnMr/SxY1T4QS/bBbAC1YvD/7X30DPHrWKR3/3LfLcsc9TUN2
 smTlZQjHdgBbGfVPL7JN0fQwA82HEjNSZKLJ0w9uFjxXgnoKT3znpUpQeuf3dsWm
 BhEFqN1Rf446S4ft2btBSB2nhX4NTlJ7w6z2F65xgaylgYFsGFTYcpjiOurKe3wF
 gGsw31DZdcuI4/LjiWbNGRKbMd7HFFLbFDMJ16TFbNcNr+pM3qpoQ6z3uMbfCBSe
 xFnYr+ESN8F2HXMNLiz3CTqLY+Fi/bHd22n3KuI9qsWws/0KDUrTvFh9Sm3kYji5
 QwwLl6PRoeFw8H29e3KrPsKoY/BGYAvrAetnC1o79cDFPLwUyii/1B6WwzC4ynfs
 K1VhwdVOwnp0sS/a2Pv8sZBpDNI07gwT9P20aiholxgREq2RKNXXVxGGFfK5Qvm9
 FG4Vp6EKEQ0=
 =G60S
 -----END PGP SIGNATURE-----

Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
 "These are mostly new device tree bindings for existing drivers, as
  well as changes to the device tree source files to add support for
  those devices, and a couple of new boards, most notably Samsung's
  Exynos5 based Chromebook.

  The changes depend on earlier platform specific updates and touch the
  usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."

* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
  ARM: exynos: dts: cros5250: add EC device
  ARM: dts: Add sbs-battery for exynos5250-snow
  ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
  ARM: dts: add mshc controller node for Exynos4x12 SoCs
  ARM: dts: Add chip-id controller node on Exynos4/5 SoC
  ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
  ARM: davinci: da850-evm: add SPI flash support
  ARM: davinci: da850: override SPI DT node device name
  ARM: davinci: da850: add SPI1 DT node
  spi/davinci: add DT binding documentation
  spi/davinci: no wildcards in DT compatible property
  ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
  ARM: dts: mvebu: introduce internal-regs node
  ARM: dts: mvebu: Convert all the mvebu files to use the range property
  ARM: dts: mvebu: move all peripherals inside soc
  ARM: dts: mvebu: fix cpus section indentation
  ARM: davinci: da850: add EHRPWM & ECAP DT node
  ARM/dts: OMAP3: fix pinctrl-single configuration
  ARM: dts: Add OMAP3430 SDP NOR flash memory binding
  ARM: dts: Add NOR flash bindings for OMAP2420 H4
  ...
2013-05-07 11:06:17 -07:00
Lucas Stach 92b775c294 i2c: mxs: do error checking and handling in PIO mode
In PIO mode we can end up with the same errors as in DMA mode, but as IRQs
are disabled there we have to check for them manually after each command.

Also don't use the big controller reset hammer when receiving a NAK from a
slave. It's sufficient to tell the controller to continue at a clean state.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-04-15 18:29:58 +02:00
Lucas Stach 535ebd217d i2c: mxs: remove races in PIO code
This commit fixes the three following races in PIO code:

- The CTRL0 register is racy in itself, when programming transfer state and
  run bit in the same cycle the hardware sometimes ends up using the state
  from the last transfer. Fix this by programming state in one cycle, make
  sure the write is flushed down APBX bus by reading back the reg and only
  then trigger the run bit.

- Only clear the DMAREQ bit in DEBUG0 after the read/write to the data reg
  happened. Otherwise we are racing with the hardware about who touches
  the data reg first.

- When checking for completion of a transfer it's not sufficient to check
  if the data engine finished, but also a check for i2c bus idle is needed.
  In PIO mode we are really fast to program the next transfer after a finished
  one, so the controller possibly tries to start a new transfer while the
  clkgen engine is still busy writing the NAK/STOP from the last transfer to
  the bus.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-04-15 18:26:46 +02:00
Shawn Guo e5aba13da0 i2c: i2c-mxs: move to use generic DMA helper
With the generic DMA device tree helper supported by mxs-dma driver,
client devices only need to call dma_request_slave_channel() for
requesting a DMA channel from dmaengine.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
2013-04-04 21:22:45 +08:00
Lars-Peter Clausen bf51a8c5e0 i2c: Ignore return value of i2c_del_adapter()
i2c_del_adapter() always returns 0. So all checks testing whether it will be
non zero will always evaluate to false and the conditional code is dead code.
This patch updates all callers of i2c_del_mux_adapter() to ignore the return
value and assume that it will always succeed (which it will). In a subsequent
patch the return type of i2c_del_adapter() will be made void.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-04-02 07:06:03 +02:00
Doug Anderson 55827f4aa6 i2c: Remove unneeded xxx_set_drvdata(..., NULL) calls
There is simply no reason to be manually setting the private driver
data to NULL in the remove/fail to probe cases.  This is just extra
cruft code that can be removed.

A few notes:
* Nothing relies on drvdata being set to NULL.
* The __device_release_driver() function eventually calls
  dev_set_drvdata(dev, NULL) anyway, so there's no need to do it
  twice.
* I verified that there were no cases where xxx_get_drvdata() was
  being called in these drivers and checking for / relying on the NULL
  return value.

This could be cleaned up kernel-wide but for now just take the baby
step and remove from the i2c subsystem.

Reported-by: Wolfram Sang <wsa@the-dreams.de>
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
2013-02-22 00:25:50 +01:00
Marek Vasut 626f0a2ff6 i2c: mxs: Implement arbitrary clock speed derivation algorithm
This patch drops the i2c timing tables from this driver and instead
derives the timing based from the requested clock sleep. The timing
tables were completely wrong anyway when observed on a scope.

This new algorithm is also only derived by using a scope, but it seems
to produce much more accurate result.

Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
[wsa: changed messages from dev_err to dev_warn]
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
2013-02-10 19:55:14 +01:00
Marek Vasut fc91e40123 i2c: mxs: Add PIO and mixed-DMA support
Add support for the PIO mode and mixed PIO/DMA mode support. The mixed
PIO/DMA is the default mode of operation. This shall leverage overhead
that the driver creates due to setting up DMA descriptors even for very
short transfers.

The current boundary between PIO/DMA 8 bytes, transfers shorter than 8
bytes are transfered by PIO, longer transfers use DMA. The performance
of write transfers remains unchanged, while there is a minor improvement
of read performance. Reading 16KB EEPROM with DMA-only operations gives
a read speed of 39.5KB/s, while with then new mixed-mode the speed is
blazing 40.6KB/s.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2013-01-28 05:26:45 +01:00
Fabio Estevam 0f40cbc4f8 i2c: mxs: Fix type of error code
cmd_err is used to handle error code, so it should not be unsigned.

This fixes the following warning when building with W=1 option:

drivers/i2c/busses/i2c-mxs.c: In function 'mxs_i2c_xfer_msg':
drivers/i2c/busses/i2c-mxs.c:331:19: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: stable@kernel.org
2013-01-22 09:54:23 +01:00
Marek Vasut 85de7fac39 i2c: mxs: Fix misuse init_completion
The init_completion() call does reinit not only the variable carrying
the flag that the completion finished, but also initialized the
waitqueue associated with the completion. On the contrary, the
INIT_COMPLETION() call only reinits the flag.

In case there was anything still stuck in the waitqueue, subsequent call
to init_completion() would be able to create possible race condition. This
patch uses the proper function and moves init_completion() into .probe() call
of the driver, to be issued only once.

Note that such scenario is impossible, since two threads can never enter the
mxs_i2c_xfer_msg(), since whole this section is protected by mutex in I2C core.
This by no means allows this issue to exit though.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2013-01-21 16:26:29 +01:00
Bill Pemberton 0b255e927d i2c: remove __dev* attributes from subsystem
CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com> (for ocores and mux-gpio)
Acked-by: Havard Skinnemoen <hskinnemoen@gmail.com> (for i2c-gpio)
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> (for puf3)
Acked-by: Barry Song <baohua.song@csr.com> (for sirf)
Reviewed-by: Jean Delvare <khali@linux-fr.org>
[wsa: Fixed "foo* bar" flaws while we are here]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-12-22 20:13:45 +01:00
Marek Vasut 8f414059c6 i2c: mxs: Do not disable the I2C SMBus quick mode
There is no reason to disable the I2C SMBus quick mode on this
IP block. Enable it. This essentially fixes the problem with the
"i2c-detect" command for probing the bus.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-22 23:03:15 +01:00
Marek Vasut c35d3cfdbc i2c: mxs: Handle i2c DMA failure properly
Properly terminate the DMA transfer in case the DMA PIO transfer
or setup fails for any reason.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-22 23:03:09 +01:00
Wolfram Sang 82fa63bd6b i2c: mxs: remove broken PIOQUEUE support
This I2C master can do DMA and PIOQUEUE (PIO with FIFO). Originally,
only PIOQUEUE was supported and it had issues, then DMA support was added
this cycle. The original intention was to keep PIOQUEUE since it has
less overhead what is nice for small transfers. However, runtime
switching between PIOQEUE and DMA depending on the transfer size never
worked despite a lot of trying. Since PIOQUEUE mode itself was flaky
(polling at places where interrupts failed to work) and the
implementation also imposed a size limit for transfers, it is best to
remove the support, so users don't fall over its limitations. It also
makes the driver a lot cleaner and more robust. If somebody really wants
less overhead, plain PIO mode could still be implemented with the
addidtional advantage that this mode is also available on MX23, too.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
2012-11-02 10:52:32 +01:00
Marek Vasut 62885f59a2 MXS: Implement DMA support into mxs-i2c
This patch implements DMA support into mxs-i2c. DMA transfers are now enabled
via DT. The DMA operation is enabled by default.

Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>

[wsa: rebased to 3.6-rc7]

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-10-08 12:47:33 +02:00
Wolfram Sang 72ee734a67 i2c: mxs: correctly setup speed for non devicetree
Commit cd4f2d4 (i2c: mxs: Set I2C timing registers for mxs-i2c) only
covered the case for devicetree and made platform_data based boards
bail out with -EINVAL. Correctly support the latter one, too.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 17:55:22 +02:00
Marek Vasut cd4f2d4aa7 i2c: mxs: Set I2C timing registers for mxs-i2c
This patch configures the I2C bus timing registers according
to information passed via DT. Currently, 100kHz and 400kHz
modes are supported.

The TIMING2 register value is wrong in the documentation for
i.MX28! This was found and fixed by:
  Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-07-13 10:33:42 +02:00
Marc Kleine-Budde a55b44ac3f i2c: mxs: mxs_i2c_finish_read: mute flase positive uninitialized var
This patch mutes the false positive compiler warning:

drivers/i2c/busses/i2c-mxs.c: In function 'mxs_i2c_xfer_msg':
drivers/i2c/busses/i2c-mxs.c:206:8: warning: 'data' may be used uninitialized in this function [-Wuninitialized]
drivers/i2c/busses/i2c-mxs.c:196:6: note: 'data' was declared here

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-07-09 13:08:15 +02:00
Linus Torvalds 84a442b9a1 arm-soc: device tree conversions, part 2
These continue the device tree work from part 1, this set is for the
 tegra, mxs and imx platforms, all of which have dependencies on clock
 or pinctrl changes submitted earlier.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPuex7AAoJEIwa5zzehBx3xsQP/jkyt74MvuKUi8pi2zkeMIgn
 4XieyqcA0KZjJzfB22q3GIZjNIf/mEIGE4E/3bneVMPh/E2zaiohaXFExBmjNjml
 hhzWeZlFGPBjrZsfpIXJIIUhwSI7gX2rjYh4npJmdNhZmy8Y89XnpNJhN1kOwMuV
 oN23hPWoSVGbyDMQ0fmHx9GyOL8m7yap+joG13aljDa2OKpQg+pYvdwft+k1K9di
 8yPF+qA043UUR7dSsjmTbiCcjZy2eySdCmfOAkEG4inSgxNoM7GBs3MuwZo/veCD
 v5WssJqWDbLXtqKn5Uo2bvGWiEcf0xtwOAqhSpbaup3dQFJSWMEenBTtA9UlxFhk
 6gdY62O+7k6N0thkxXyLNGkgaGzexZAsK7dM6XSDB+PqD+OSNJS7dvmxZM8tuaRn
 rvCM1XWcNeN/dpnLbgwCR12efkwWtJoqqUZUUp/tFFaTo8HriqeAIYk7obnR8s9n
 S5x9LeueQGNgaxXJzVdh481YKG/1lqjG/a06HbVgYS4XQvtdA+4khalOefJv10tm
 Nkg8+4/8pMthWJfhhlfPUgWFXOXFF2AGPG4su2XwKuFXypO8599lzi7gUQaEZu2U
 7caqoWP69KsKvK5iAAmA4DQ2rcsgHd44NXx/8Jjes9ma8knlYjrf42dBH6AZMQBG
 69I9sJ1cyqusBwx72NPN
 =WeDQ
 -----END PGP SIGNATURE-----

Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm-soc device tree conversions (part 2) from Olof Johansson:
 "These continue the device tree work from part 1, this set is for the
  tegra, mxs and imx platforms, all of which have dependencies on clock
  or pinctrl changes submitted earlier."

Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
  ARM: dt: tegra: invert status=disable vs status=okay
  ARM: dt: tegra: consistent basic property ordering
  ARM: dt: tegra: sort nodes based on bus order
  ARM: dt: tegra: remove duplicate device_type property
  ARM: dt: tegra: consistenly use lower-case for hex constants
  ARM: dt: tegra: format regs properties consistently
  ARM: dt: tegra: gpio comment cleanup
  ARM: dt: tegra: remove unnecessary unit addresses
  ARM: dt: tegra: whitespace cleanup
  ARM: dt: tegra cardhu: fix typo in SDHCI node name
  ARM: dt: tegra: cardhu: register core regulator tps62361
  ARM: dt: tegra30.dtsi: Add SMMU node
  ARM: dt: tegra20.dtsi: Add GART node
  ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
  ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
  ARM: dt: tegra: Add device tree support for AHB
  ARM: dts: enable audio support for imx28-evk
  ARM: dts: enable i2c device for imx28-evk
  i2c: mxs: add device tree probe support
  ARM: dts: enable mmc for imx28-evk
  ...
2012-05-26 12:57:47 -07:00
Linus Torvalds 39b6cc668c arm-soc: add stmp-dev library code
A number of devices are using a common register layout, this adds support
 code for it in lib/stmp_device.c so we do not need to duplicate it in
 each driver.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPuexlAAoJEIwa5zzehBx31P0P/jK7GC5Ln2gr/bV+4Kt9fStS
 VcGI/ARsyQtwaNTJQfPkg8Weg3DhbPRlUWeimVKMFo3uEle3VjnPBjdcMPUKtW3x
 SPka/W591LGEdKQRmXZrISm2OiQXVvM2zkhSJV89n/tJBdHd+tDWDDq4Y784F8Cj
 hWmcIi66G4RBPj5pplf80UhNAEg5HoZHQnlgrS1iLMpBTwXAesv7zyZpvnsMzdpg
 qSJTfcifgLULtM0WFbooNGojBn8ftuA67psrw78vgV2bz7bVBioZHYFyqPWK9Gr0
 vtiKuyXqiDA65mueXA+E5RXXLCLQSyGdV8y0xiSYjilRVkziPcMKnQT07keb8SJN
 CCDpetjEULiQpgKvVWc7sDGlb5ePd/C5rs31S0fFOKjeRJNlfG5+OuqZPiobO7hk
 F2Fx3gq4LPLel7gwjK3T4XTmmL9kNt/y1sIfXx5WybJL8N5n6TdZIfWm6yOZYwfX
 jvG/CnvVvhgdWk/ebaTEOG1MaeNAY3uwGpSBuEEoXUDHatQdOYAsgLfJJv/H4zKp
 2AY9qvXTDtFYys/hs2WhwmS7s1WFlIrA+voEPBDa3WT2qGup8HAL/C9kL3ms2zqk
 8JL/yQ/IJpTHPb4bCGo9C08qdi1YtMbylHB0/ELvG1BNoHOnCDV3wZlVG3ZTQQb5
 c/Lb2H8crk5HVbpCPLQU
 =VHLM
 -----END PGP SIGNATURE-----

Merge tag 'stmp-dev' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm-soc stmp-dev library code from Olof Johansson:
 "A number of devices are using a common register layout, this adds
  support code for it in lib/stmp_device.c so we do not need to
  duplicate it in each driver."

Fix up trivial conflicts in drivers/i2c/busses/i2c-mxs.c and
lib/Makefile

* tag 'stmp-dev' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  i2c: mxs: use global reset function
  lib: add support for stmp-style devices
2012-05-26 12:50:04 -07:00
Linus Torvalds 813a95e5b4 arm-soc: soc-specific pinctrl changes
With this, five platforms are moving to the relatively new pinctrl
 subsystem for their pin management, replacing the older soc specific
 in-kernel interfaces with common code.
 
 There is quite a bit of net addition of code for each platform being
 added to the pinctrl subsystem. but the payback comes later when adding
 new boards can be done by only providing new device trees instead.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPuw1/AAoJEIwa5zzehBx3wbsP/RFCYzMVyz85BNLQuRyY9eO2
 GCRWd0Vvy3fIfypiPdHdhkq6nIU/JnxgsfBbKX9FvWqvxXi96Ojh13KSIhSI1rQ9
 t14VyuwUXaS3leeCyKxhNF1vRscz2iyEGXJqp+XEN4ckf2nrQCpKBiY5Eg9sH6/J
 fvYgSBY9Lf9nFAn+/wqSKIfdvw7H0NXwUdsLvNU0uCwvrSG929bTxx2AnHX00TdJ
 qf4XLhmatMg1uwdUgL/99ZxxgHlj6o55u7S6aRhUWXNXCimV6uEZ1F35ET37b+x3
 YUltBCIaXjFR7iwNHmkkl42d8uyfkBznB555sY5qS3G/uF5Ma1R5I7fv8EIEy+2w
 bVHsva4lj1yFazic6m8yKTET4i8n6OPiKVNqGnDsp2yb6WzOGSliKdr0Jlo1oNG2
 gS69LcDZxCkXrqEq0Ht8uUoCo9TWei+qhJ6ZOJ1Z3+9ZyFq1iRTKgPVxyA5VaHaB
 wwBbqKrohAwuExY8/gkAj6SYqBOF3l/J8QSB2JjXyj4trLC5UMq+l3L4cIWyMRPc
 fil83hV6460CiIBoKcsnV9hDUS0oh74mv52zHo0Xj73qABqZ4dcrpHVayWjtMtpl
 Z+tUpvD1rMQ+E0gdXDrwMrwILVyCDsBvpFKF4avnujDJ4WmyywtKZ+xvnpMd73VZ
 YrI/+XQsMT8ZfVkkj54D
 =HIfz
 -----END PGP SIGNATURE-----

Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm soc-specific pinctrl changes from Olof Johansson:
 "With this, five platforms are moving to the relatively new pinctrl
  subsystem for their pin management, replacing the older soc specific
  in-kernel interfaces with common code.

  There is quite a bit of net addition of code for each platform being
  added to the pinctrl subsystem.  But the payback comes later when
  adding new boards can be done by only providing new device trees
  instead."

Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}

* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
  mtd: nand: gpmi: fix compile error caused by pinctrl call
  ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
  ARM: nomadik: enable PINCTRL_NOMADIK where needed
  ARM: mxs: enable pinctrl support
  video: mxsfb: adopt pinctrl support
  ASoC: mxs-saif: adopt pinctrl support
  i2c: mxs: adopt pinctrl support
  mtd: nand: gpmi: adopt pinctrl support
  mmc: mxs-mmc: adopt pinctrl support
  serial: mxs-auart: adopt pinctrl support
  serial: amba-pl011: adopt pinctrl support
  spi/imx: adopt pinctrl support
  i2c: imx: adopt pinctrl support
  can: flexcan: adopt pinctrl support
  net: fec: adopt pinctrl support
  ARM: ux500: switch MSP to using pinctrl for pins
  ARM: ux500: alter MSP registration to return a device pointer
  ARM: ux500: switch to using pinctrl for uart0
  ARM: ux500: delete custom pin control system
  ARM: ux500: switch over to Nomadik pinctrl driver
  ...
2012-05-22 09:39:42 -07:00
Shawn Guo b237866848 i2c: mxs: add device tree probe support
Add device tree probe support for i2c-mxs driver.  So far, it's only
been tested on imx28.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
2012-05-13 08:27:44 +08:00
Shawn Guo 844d0b5a0b Merge branches 'clk/mxs' and 'imx/pinctrl/for-3.5' into mxs/dt/for-3.5 2012-05-12 13:32:09 +08:00
Shawn Guo d98d033c15 i2c: mxs: adopt pinctrl support
Cc: linux-i2c@vger.kernel.org
Cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-05-12 09:43:17 +08:00
Wolfram Sang 1e4f0b8257 i2c: mxs: disable QUEUE when sending is done
Since the last fixes to this driver ensure now the queue termination is
done correctly, we can finally disable the queue after a transfer
without problems. The gain is that it will only be reenabled after the
next transfer is fully set up. Before, the queue was running all the
time and if the setup of the next message was interrupted by another
thread, an incomplete buffer could have been sent, padded with zeroes.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-04-27 16:13:29 +02:00
Wolfram Sang c95eeae9e3 i2c: mxs: handle spurious interrupt
After an error interrupt setting cmd->err, I see another interrupt that
the data engine is empty which clears cmd->err before being processed.
So, clear cmd->err at the beginning of a transfer only to handle these
consecutive interrupts.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-04-25 22:59:44 +02:00
Wolfram Sang 6b866c151a i2c: mxs: use global reset function
The former mach specific reset_block function has been converted to a global
one. Use the new one to remove mach dependency from the driver.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-04-20 23:27:18 +02:00
Wolfram Sang 844990daa2 i2c: mxs: only flag completion when queue is completely done
The hardware generates an interrupt for every completed command in the
queue while the code assumed that it will only generate one interrupt
when the queue is empty. So, explicitly check if the queue is really
empty. This patch fixed problems which occurred due to high traffic on
the bus. While we are here, move the completion-initialization after the
parameter error checking.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Cc: stable@kernel.org
2012-02-24 22:28:27 +01:00
Lucas De Marchi 25985edced Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-31 11:26:23 -03:00
Sascha Hauer 6b7d815c3f i2c-mxs: set controller to pio queue mode after reset
mxs_reset_block() clears the PIO_QUEUE_MODE bit. So we have
to set it again after a controller reset.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2011-03-20 23:54:52 +00:00
Wolfram Sang a8da7fecb6 i2c: add driver for Freescale i.MX28
Currently only supporting the PIOQUEUE-mode, because DMA-support for
this platform is not yet in mainline. When it becomes available and
support has been added to this driver, it will also be suitable for
i.MX23 and STMP3xxx.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2011-02-23 01:00:11 +00:00