When the AFIFO is not enabled but more than one serializers are used the DMA
need to transfer number of words equal to active serializers when a DMA
request is generated.
When configuring the burst for the DMA avoid using value '1' for the burst
since it is going to enable additional logic in the DMA drivers. Burst '1'
means that the DMA should send/receive one word per DMA requests.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Configure the AFIFO numevt parameter based on the requested tx/rx_numevt,
active serializers and period size in words.
In this way McASP can adopt it's (and the DMA) configuration runtime and
can pick the most optimal setup which satisfy the parameters.
This way we do not need to place any constraint on the stream itself,
allowing application greater freedom on how they want to set up ALSA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move the dma_params->fifo_level and dma_data->maxburst configuration to the
mcasp_common_hw_param() function where we configure the AFIFO registers.
It makes the code regarding to AFIFO and DMA configuration more easy to
follow since it is now clear how the AFIFO and how the DMA is going to be
configured.
Previously this has been done in two functions using a bit different
calculation form - which ended up with the same result in both case at the
end, but it was confusing.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We can have more linear code flow by using variables in
mcasp_common_hw_param() related to the AFIFO configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set up the playback_dma_data/capture_dma_data for the dai at probe
time since the generic dmaengine PCM stack needs to have access to
this information early.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
IB_NF, NB_IF and IB_IF configured the bc polarity incorrectly. The receive
polarity was set to the same edge as the TX in these cases.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When we boot with non-DT mode the damengine will need the channel number and
a filter function in order to get the channel.
The filter_data is filled in the DAI driver while the filter_function will
be provided by the edma-pcm driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It is quite confusing to name the pointer to davinci_pcm_dma_params as
dma_data. Rename the pointer to avoid confusion.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move the context register storage behind of a struct and use a pointer to
it in the suspend/resume callbacks to remove the long lines.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Rename the struct for the platform data:
snd_platform_data -> davinci_mcasp_pdata
Since we have users under arch/arm/mach-davinci/ for this struct add
temporary define to avoid breakage. The arch code can be updated later to
use the new struct name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Rearrange the code in the function for readability.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Handle the PM callbacks via the ASoC core instead of device core.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Take the return value from mcasp_common_hw_param() and use that in case of
error.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The use of pm_runtime in trigger() callback is not correct and it will lead
to unbalanced power.usage_count.
The only place which might need to call pm_runtime is the set_fmt callback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
These registers can be configured synchronously for playback and capture.
Furthermore when McASP is in master and sync mode the capture operation
needs the TX path to be configured in order to be able to provide the needed
clocks for the bus.
xxFMT and xxFMCT registers has been already configured for both TX and RX
other places in the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of
davinci_hw_common_param - for common, I2S/DIT mode settings
davinci_hw_dit_param - for DIT protocol configuration
davinci_hw_param - for I2S (and compatible protocols)
Use the following names:
mcasp_common_hw_param, mcasp_dit_hw_param and mcasp_i2s_hw_param.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make BCLK divider setting implicite in hw_params call if McASP device
is the bit clock master on the audio serial bus.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Optional DT property to specify the desired parent clock for the McASP fck
clock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
An earlier patch overlooked this when the compatible has been changed from
omap2 -> am33x.
Rename omap2_mcasp_pdata to am33xx_mcasp_pdata.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of passing __iomem address (mcasp->base + register_offset) pass
the main mcasp structure and only access the mcasp->base in the low level
IO functions.
In most cases this helps with code readability and it will make it easier
to switch over to regmap in the future.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The IP in DRA7xx is similar to the IP found in TI81xxAM3xxx/AM4xxx type of
SoCs but it is is integrated with sDMA instead of eDMA. The suitable pcm
driver for DRA7xx is the omap-pcm driver which is using dmaengine.
In the driver we can configure both dma related structures used for eDMA and
sDMA. The only thing we need to make sure that we set the correct dma_data
at startup with snd_soc_dai_set_dma_data()
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In synchronous mode both transmit and receive sections are using the TX
clocks. In setup like this the TX clocks need to be enabled when capture
is running.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The audio data to/from McASP can be sent/received via two method:
Via the data port (preferred) or via the configuration bus.
Currently the driver assumes that all data communication will be done via
the data port.
This patch adds support for selecting the configuration port as data
interface.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The FIFO registers base address is different in dm646x compared to newer
SoCs with McASP IP. Instead of using two paths (switch/case) to handle the
difference we can simply pick the correct base address beforehand and use
offsets to address the register we need to configure.
With this change the indentation depth can be reduced as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Replace mcasp->base use with plain base in the davinci_mcasp_set_dai_fmt()
function since it has been already used by the remaining part of the function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Rename the private struct from davinci_audio_dev to davinci_mcasp.
Change the local use of the pointer to this struct from *dev to *mcasp.
The aim is to have better readable code for the first look since having
dev->xxxx in the code when using the local private struct is a bit
surprising.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It brings no benefit to inline this function due to it's size and function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since it is a private struct strictly used by the davinci-mcasp driver it
can be moved from header file to the source file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It is better for readability to have the register definitions out from the
source file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The serial-dir array gives this information so there is no need to have the
num-serializer property in DT description.
Just ignore the property in the driver the DTS files can be updated
separately without regression.
Update the documentation at the same time for davinci-mcasp
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Change the model omap2-mcasp-audio in compatible property to
am33xx-mcasp-audio as omap2 does not have mcasp.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Extract DMA channels directly from DT as they can not be found from
platform resources anymore. This is a work-around until davinci audio
driver is updated to use dmaengine.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a separate register location for data port registers to
mcasp DT bindings. On am33xx SoCs the McASP registers are mapped
trough L4 interconnect, but data port registers are also mapped trough
L3 bus to a different memory location.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When the system returns from suspend, it looses its configuration. Most
of it is restored by running a normal audio stream startup, but the DAI
format is left unset as that's configured on the audio device creation.
Hence, it suffices here to care for the registers which are touched by
davinci_mcasp_set_dai_fmt() and restore them when the system is resumed.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
'mcasp_dt_ids' is always compiled in. Hence of_match_ptr is not
necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
McASP serial audio engine needs different rotation values on TX and RX
channels. Commit dde109fb46 ("ASoC: McASP: Fix data rotation for
playback. Enables 24bit audio playback") changed the calculation to fix
the playback format, but broke the capture stream by doing it for both
TXFMT and RXFMT.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org [3.9 only]
A few more bug fixes, the DAPM clock fix is actually a driver specific
one since currently there's only one user of the clock support due to
the problems relying on the clock API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=WQzu
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.10
A few more bug fixes, the DAPM clock fix is actually a driver specific
one since currently there's only one user of the clock support due to
the problems relying on the clock API.
According documentation bit ACLKRPOL is set to 0 (receiver samples data
on falling edge) and when set to 1 (receiver samples data on rising edge).
I2S data are always sampled on falling edge and valid during rising edge
of bit clock. So in case of capture data transmitter sample data on falling
edge and macsp must read then on rising edge.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When McASP is bit clock and frame clock master enable pin output for rx clocks.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For TDM mode, BCLK-to-LCLK ratio is computed as (tdm_slots) x (word_length).
I2S mode is only subset of TDM mode with specific tdm_slots = 2 channels.
Also bclk_lrclk_ratio can be greater than 255, therefore u16 need to be used.
Signed-off-by: Michal Bachraty <michal.bachraty@streamunlimited.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As pointed of by Vaibhav, commit message: "ASoC: davinci-mcasp: Add support for multichannel playback"
number of active serializers can be hidden into fifo_level variable, which is set in davimci-mcasp.
Signed-off-by: Michal Bachraty <michal.bachraty@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Channel size settings will be made at the end of
davinci_mcasp_hw_params() routine and thus overwrite frame
format settings made for DIT mode. This patch fixes this issue
by taking op_mode into account. Tested with official PSP 3.2
kernel and sii9022a HDMI transmitter.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
AFSX won't be used in DIT mode. The related pins are AHCLKX and
the data pins.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Peter Ujfalusi