None of the Kconfigs for any of these drivers are tristate,
meaning that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only. All
drivers get similar changes, so they are handled in batch.
We remove module.h from code that isn't doing anything modular at
all; if they have __init sections, then replace it with init.h.
A couple drivers have module_exit() code that is essentially orphaned,
and so we remove that.
Quite a few bool drivers (hence non-modular) are converted over to
to builtin_platform_driver().
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Pritesh Raithatha <praithatha@nvidia.com>
Cc: Ashwini Ghuge <aghuge@nvidia.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
NVIDIA's Tegra210 support the park bit to make pinmux configuration
enable/disable. If parked bit is 1 then configuration does not apply
and if it is 0 then pinmux configuration applies. This is to support
to avoid any glitch in pinmux configurations.
The parked bit is part of mux register and mux bank and hence it is
not required to have member for the parked_reg and parked bank very
similar to other bit field of the same register.
Remove the need of the parked register and parked bank and get whether
parked function supported or not by parked_bit.
This is to make the parked bit handling same as other fields of mux
registers.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_pinctrl_register() for pin control registration and remove
need of .remove callback.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Parking bits might not be cleared by the bootloader properly (if for
instance it doesn't use the device configured by that pin). Clear
the park bits for all the pins during pinctrl probe.
This is present on T210 platforms but not earlier ones, so for earlier
generations, set parked_reg = -1 to disable.
The park bit is used to prevent glitching when reprogramming pinctrl
registers.
Based on work by:
Shravani Dingari <shravanid@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra has several pinctrl drivers. Now it is reasonable enough to
move them into drivers/pinctrl/tegra/.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Paul Gortmaker