The Kirkwood CPU Freq driver needs a CPU definition in order for the probe
routine to activate it. Add a suitable definition to kirkwood.dtsi
This definition is only correct for single core SoCs. There is a dual core
SoC in the kirkwood family (88F632X) but the rest of the Kirkwood drivers in
the kernel don't currently support it. If they ever do the cpus definition
would need to be duplicated in each of the SoC specific include files.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This controller is used to access the reset management FPGA of the
km_kirkwood boards.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Some kirkwood variants (for instance present in the prestera SoCs) do
not have all the peripherals whose nodes are declared in
kirkwood.dtsi. These missing peripherals are SATA, SDIO, and RTC.
As discussed in [1], to avoid that these missing peripherals get
initialized which could result in system hangs when accessing
undocumented/not present HW registers, their corresponding OF nodes
should not get declared at all for some kirkwood variants.
The corresponding OF nodes of these peripherals thus are moved from
kirkwood.dtsi to the kirkwood-628x.dtsi files so that they still are
initialized for these variants where they are present.
[1]
http://lists.infradead.org/pipermail/linux-arm-kernel/2013-May/167154.html
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Kirkwood-based PlatHome OpenBlocks A6 board has an Init button
connected to MPP pin 38. This commit adds support for this button.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Atsushi Yamagata <yamagata@plathome.co.jp>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instead of having one separate pinmux configuration for each LED, for
each GPIO of the GPIO header, for each DIP switch, this patch groups
them together in configurations that make sense together: LEDs on one
side, GPIOs of the GPIO header on another side, and DIP switches on
yet another side.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Atsushi Yamagata <yamagata@plathome.co.jp>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-By: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-By: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Atsushi Yamagata <yamagata@plathome.co.jp>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
Note that some of the LEDs pinmux configurations are kept in the
pinctrl node, because they are not used by the gpio-leds driver.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Kirkwood iConnect Device Tree is currently using totally
meaningless names for the pinmux configuration: pmx_gpio_XY.
This patch fixes that by using some more meaningful names such as
pmx_button_power.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP GP board has two USB slots: one on the front side and
one on the back side. This commit enables the two USB host controllers
that correspond to those wo USB slots.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Besides the two "classic" USB interfaces with normal USB ports on the
front side, the PlatHome OpenBlocks AX3 uses the third USB interface
of the Marvell SoC in the mini-PCIe connector. This allows certain
mini-PCIe cards to expose parts of their functionality as a USB
peripheral.
This commit enables this third USB interface in the OpenBlocks AX3
Device Tree, and also adds comments on top of the two other USB
interfaces so that the Device Tree makes it clear which USB interface
at the SoC level matches which USB interface visible on the board.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Atsushi Yamagata <yamagata@plathome.co.jp>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP Development Board (DB-78460-BP) has a NOR flash device
connected to the Device Bus. This commit adds the device tree node
to support this device.
This SoC supports a flexible and dynamic decoding window allocation
scheme; but since this feature is still not implemented we need
to specify the window base address in the device tree node itself.
This base address has been selected in a completely arbitrary fashion.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to prepare the switch to the standard MMC device tree parser
for mvsdio, adapt all current uses of mvsdio in the dts files to the
standard format.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds the device tree node for si5351 clock generator
and the corresponding oscillator connected to it. It also limits
i2c frequency to 100kHz as there are bus locks reported on higher
frequencies.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The 'samsung,vbus-gpio' was submitted before pinmux landed for
exynos5250 and uses the old-style gpio specifier. Fix the two
exynos5250 boards that use it.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The kernel crashes while resuming from AFTR idle mode. It happens
because L2 cache was not going into retention state.
This patch configures the USE_RETENTION bit of ARM_L2_OPTION register
so that it does not depend on MANUAL_L2RSTDISABLE_CONTROL of
ARM_COMMON_OPTION register for L2RSTDISABLE signal.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Tested-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix triggering for GPIO interrupts that's needed for 4430sdp
Ethernet. Otherwise booting with nfsroot won't work.
- Fix CPU operating point values
- Fix wrong assumption that twl PMIC is always connected to omap3
- Add gpmc for am33xx so beaglebone users can use the bus
- Cosmetic fix for mcspi pin muxing to avoid confusion
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/Y67
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/dt-fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Omap device tree fixes for issue discovered during the merge window:
- Fix triggering for GPIO interrupts that's needed for 4430sdp
Ethernet. Otherwise booting with nfsroot won't work.
- Fix CPU operating point values
- Fix wrong assumption that twl PMIC is always connected to omap3
- Add gpmc for am33xx so beaglebone users can use the bus
- Cosmetic fix for mcspi pin muxing to avoid confusion
* tag 'omap-for-v3.10/dt-fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: don't assume boards are using twl4030 for omap3
ARM: dts: Configure and fix the McSPI pins for 4430sdp
ARM: dts: AM33XX: Add GPMC node
ARM: dts: OMAP4460: Fix CPU OPP voltages
ARM: dts: OMAP36xx: Fix CPU OPP voltages
ARM: dts: OMAP4: Fix ethernet IRQ for OMAP4 boards
- Few GPMC fixes and binding doc updates noted after sending
pull requests for the GPMC branch.
- Board fixes for beagle usb host and rx51 spi probe order
- SoC fixes dt earlyprintk, omap1 dma and omap2+ id.c error
handling fixes
Then few minor things that are not strictly fixes but are good
to get out of the way:
- Add missing legacy mux registers for am/dm73x gpio
- Add detection for am33xx pg2.1 silicon
- Enable twl4030 audio modules in defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lnij
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/fixes-for-merge-window-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Omap fixes for things that were discovered during the merge window:
- Few GPMC fixes and binding doc updates noted after sending
pull requests for the GPMC branch.
- Board fixes for beagle usb host and rx51 spi probe order
- SoC fixes dt earlyprintk, omap1 dma and omap2+ id.c error
handling fixes
Then few minor things that are not strictly fixes but are good
to get out of the way:
- Add missing legacy mux registers for am/dm73x gpio
- Add detection for am33xx pg2.1 silicon
- Enable twl4030 audio modules in defconfig
* tag 'omap-for-v3.10/fixes-for-merge-window-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove bogus IS_ERR_OR_NULL checking from id.c
ARM: OMAP4+: omap2plus_defconfig: Enable audio via TWL6040 as module
ARM: OMAP2: AM33XX: id: Add support for new AM335x PG2.1 Si
omap: mux: add AM/DM37x gpios
ARM: OMAP1: DMA: fix error handling in omap1_system_dma_init()
ARM: OMAP2+: omap_device: use late_initcall_sync
ARM: OMAP: RX-51: change probe order of touchscreen and panel SPI devices
ARM: OMAP3: Beagle: Fix USB Host on beagle xM Ax/Bx
ARM: OMAP2+: only WARN if a GPMC child probe function fail
ARM: OMAP2+: only search for GPMC DT child nodes on probe
Documentation: dt: update properties in TI GPMC NAND example
Documentation: dt: update TI GPMC ethernet binding properties
Signed-off-by: Olof Johansson <olof@lixom.net>
arch/arm/mach-ux500/board-mop500.c: In function ‘mop500_prox_activate’:
arch/arm/mach-ux500/board-mop500.c:406:18: warning: ignoring return value of
‘regulator_enable’, declared with attribute warn_unused_result
[-Wunused-result]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix db8500_read_soc_id() to read all five soc_id number locations
instead of repeating the second one two times.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Trivial patch, adding the i2c Cypress trackpad used on Snow.
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Since commit 657eee7 (media: coda: use genalloc API) the following build
error happens with imx_v4_v5_defconfig:
drivers/built-in.o: In function 'coda_remove':
clk-composite.c:(.text+0x112180): undefined reference to 'gen_pool_free'
drivers/built-in.o: In function 'coda_probe':
clk-composite.c:(.text+0x112310): undefined reference to 'of_get_named_gen_pool'
clk-composite.c:(.text+0x1123f4): undefined reference to 'gen_pool_alloc'
clk-composite.c:(.text+0x11240c): undefined reference to 'gen_pool_virt_to_phys'
clk-composite.c:(.text+0x112458): undefined reference to 'dev_get_gen_pool'
Select GENERIC_ALLOCATOR and get rid of the custom IRAM_ALLOC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit bca7a5a (ARM: cpu hotplug: remove majority of cache flushing
from platforms) removes include of <asm/cacheflush.h> and hence
discovers a few indirect inclusion and declaration problems as below.
CC arch/arm/mach-imx/hotplug.o
In file included from arch/arm/mach-imx/hotplug.c:16:0:
arch/arm/mach-imx/common.h💯29: warning: ‘struct pt_regs’ declared inside parameter list [enabled by default]
arch/arm/mach-imx/common.h💯29: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
arch/arm/mach-imx/common.h:101:29: warning: ‘struct pt_regs’ declared inside parameter list [enabled by default]
arch/arm/mach-imx/hotplug.c: In function ‘imx_cpu_die’:
arch/arm/mach-imx/hotplug.c:53:2: error: implicit declaration of function ‘cpu_do_idle’ [-Werror=implicit-function-declaration]
arch/arm/mach-imx/hotplug.c: In function ‘imx_cpu_kill’:
arch/arm/mach-imx/hotplug.c:58:26: error: ‘jiffies’ undeclared (first use in this function)
arch/arm/mach-imx/hotplug.c:58:26: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/mach-imx/hotplug.c:58:2: error: implicit declaration of function ‘msecs_to_jiffies’ [-Werror=implicit-function-declaration]
arch/arm/mach-imx/hotplug.c:61:3: error: implicit declaration of function ‘time_after’ [-Werror=implicit-function-declaration]
Fix them by adding the needed inclusion and declaration.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
* late/fixes:
ARM: OMAP2+: Fix unmet direct dependencies for SERIAL_OMAP
ARM: ux500: always select ABX500_CORE
ARM: SIRF: select SMP_ON_UP only on SMP builds
ARM: SPEAr: conditionalize l2x0 support
ARM: imx: build CPU suspend code only when needed
ARM: OMAP: build SMP code only for OMAP4/5
ARM: tegra: Tegra114 needs CPU_FREQ_TABLE
ARM: default machine descriptor for multiplatform
Signed-off-by: Olof Johansson <olof@lixom.net>
- Support partitions larger than 4GiB in device tree
- Support for new SPI chips
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iEYEABECAAYFAlGLxzEACgkQdwG7hYl686M+PgCdHAn3fDzGW7gUL1tj43NCqaC8
PWoAoNAD5YpI3wYEBxped2MjSfgbQMvq
=hM2T
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20130509' of git://git.infradead.org/linux-mtd
Pull MTD update from David Woodhouse:
- Lots of cleanups from Artem, including deletion of some obsolete
drivers
- Support partitions larger than 4GiB in device tree
- Support for new SPI chips
* tag 'for-linus-20130509' of git://git.infradead.org/linux-mtd: (83 commits)
mtd: omap2: Use module_platform_driver()
mtd: bf5xx_nand: Use module_platform_driver()
mtd: denali_dt: Remove redundant use of of_match_ptr
mtd: denali_dt: Change return value to fix smatch warning
mtd: denali_dt: Use module_platform_driver()
mtd: denali_dt: Fix incorrect error check
mtd: nand: subpage write support for hardware based ECC schemes
mtd: omap2: use msecs_to_jiffies()
mtd: nand_ids: use size macros
mtd: nand_ids: improve LEGACY_ID_NAND macro a bit
mtd: add 4 Toshiba nand chips for the full-id case
mtd: add the support to parse out the full-id nand type
mtd: add new fields to nand_flash_dev{}
mtd: sh_flctl: Use of_match_ptr() macro
mtd: gpio: Use of_match_ptr() macro
mtd: gpio: Use devm_kzalloc()
mtd: davinci_nand: Use of_match_ptr()
mtd: dataflash: Use of_match_ptr() macro
mtd: remove h720x flash support
mtd: onenand: remove OneNAND simulator
...
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
Pull slave-dmaengine updates from Vinod Koul:
"This time we have dmatest improvements from Andy along with dw_dmac
fixes. He has also done support for acpi for dmanegine.
Also we have bunch of fixes going in DT support for dmanegine for
various folks. Then Haswell and other ioat changes from Dave and
SUDMAC support from Shimoda."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (53 commits)
dma: tegra: implement suspend/resume callbacks
dma:of: Use a mutex to protect the of_dma_list
dma: of: Fix of_node reference leak
dmaengine: sirf: move driver init from module_init to subsys_initcall
sudmac: add support for SUDMAC
dma: sh: add Kconfig
at_hdmac: move to generic DMA binding
ioatdma: ioat3_alloc_sed can be static
ioatdma: Adding write back descriptor error status support for ioatdma 3.3
ioatdma: S1200 platforms ioatdma channel 2 and 3 falsely advertise RAID cap
ioatdma: Adding support for 16 src PQ ops and super extended descriptors
ioatdma: Removing hw bug workaround for CB3.x .2 and earlier
dw_dmac: add ACPI support
dmaengine: call acpi_dma_request_slave_channel as well
dma: acpi-dma: introduce ACPI DMA helpers
dma: of: Remove unnecessary list_empty check
DMA: OF: Check properties value before running be32_to_cpup() on it
DMA: of: Constant names
ioatdma: skip silicon bug workaround for pq_align for cb3.3
ioatdma: Removing PQ val disable for cb3.3
...
If a board isn't using twl4030, then dtc will complain about the missing
phandle (which is in twl4030.dtsi). Move the phy declaration to the dts
files.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 6770b211 (ARM: OMAP2+: Export SoC information to userspace)
had some broken return value handling as noted by Russell King:
+ soc_dev = soc_device_register(soc_dev_attr);
+ if (IS_ERR_OR_NULL(soc_dev)) {
+ kfree(soc_dev_attr);
+ return;
+ }
+
+ parent = soc_device_to_device(soc_dev);
+ if (!IS_ERR_OR_NULL(parent))
+ device_create_file(parent, &omap_soc_attr);
This is nonsense. For the first, IS_ERR() is sufficient. For the second,
tell me what error checking is required in the return value of this
function:
struct device *soc_device_to_device(struct soc_device *soc_dev)
{
return &soc_dev->dev;
}
when you've already determined that the passed soc_dev is a valid pointer.
If you read the comments against the prototype:
/**
* soc_device_to_device - helper function to fetch struct device
* @soc: Previously registered SoC device container
*/
struct device *soc_device_to_device(struct soc_device *soc);
if "soc" is valid, it means the "previously registered SoC device container"
must have succeeded and that can only happen if the struct device has been
registered. Ergo, there will always be a valid struct device pointer for
any registered SoC device container. Therefore, if soc_device_register()
succeeds, then the return value from soc_device_to_device() will always be
valid and no error checking of it is required.
Simples. The rule as ever applies here: get to know the APIs your using
and don't fumble around in the dark hoping that you'll get this stuff
right.
Fix it as noted by Russell.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The bootloader configures the pins, but has pull bits
set without pull enable bits. While this is harmless,
and won't do anything, it seems to cause confusion at
least for me every time looking at the pin configuration.
Fix it for DT based boot.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add GPMC data node to AM33XX device tree file.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit d16fb25 (ARM: dts: OMAP4460: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP4460 OPP data in
arch/arm/mach-omap2/opp4xxx_data.c
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit 3027e26 (ARM: dts: OMAP36xx: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP36xx OPP data in
arch/arm/mach-omap2/opp3xxx_data.c
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Boards supported upstream all use TWL6040 as audio codec, enable the common
ASoC machine driver by default for them.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adam Baker