Commit Graph

18 Commits

Author SHA1 Message Date
Emmanuel Grumbach 9b60bb6d86 iwlwifi: mvm: disable BT Co-running by default
The tables still contain dummy values.

Cc: <stable@vger.kernel.org> [3.15+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-09-21 22:20:10 +03:00
Eyal Shapira 361dbec8ac iwlwifi: mvm: choose an initial tx rate based on rssi conditions
Improve the initial tx rate and antenna selection to be based on
the rssi of the last rx. This avoids starting at the lowest legacy
rate always and requiring more tx traffic to "climb" up the rates.
Since this option might cause trouble in certain setups, allow to
disable it by default.

Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-09-21 13:25:44 +03:00
Eliad Peller 4cb832d559 iwlwifi: mvm: move IWL_MVM_UAPSD_QUEUES to constants.h
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-09-14 22:02:24 +03:00
Johannes Berg b2b7875bfb iwlwifi: mvm: don't update quota in firmware too often
When updating quota in the firmware, it has to reset quite a bit
of internal state, which apparently can have an adverse impact on
its operation.

Avoid that by only updating the quota command when there are any
signification changes, i.e. added/removed bindings or changes in
quota that are bigger than 8 TU within a binding.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-09-14 12:56:40 +03:00
Max Stepanov f3bd58f486 iwlwifi: mvm: add MVM_FW_MCAST_FILTER_PASS_ALL option
Add MVM_FW_MCAST_FILTER_PASS_ALL option to iwl-dbg-cfg.ini configuration file
to enable/disable FW multicast filtering.

Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-09-14 12:56:38 +03:00
Johannes Berg 8b4139dc9f iwlwifi: add Intel Mobile Communications copyright
Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.

For files that we have modified in the time since the change,
add the proper copyright notice now.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-09-03 22:49:07 +03:00
Emmanuel Grumbach 8286d9f50a iwlwifi: mvm: BT Coex - add reduced Tx power thresholds to constants
This really belongs to the constants file.

Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-06-24 21:55:36 +03:00
Johannes Berg 65d6662850 iwlwifi: mvm: remove using max_duration in firmware API
The firmware decided to not implement this API in this way,
so for now remove setting the field completely. This will
allow the firmware to change how to use this field later.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-03-18 21:15:38 +02:00
Emmanuel Grumbach cdb00563fe iwlwifi: mvm: BT Coex - add debugfs hook to set BT Tx priority
In order to debug the firmware, we need to be able to set
the BT priority of WiFi packets. This priority is set based
on the type of the packet (control frames, EAPOL etc...).
For debugging purposes, allow to override this priority by
a debugfs controlled value.
Enable this feature that needs this priority to be able to
test it.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-03-18 21:15:37 +02:00
Emmanuel Grumbach b9fae2d54c iwlwifi: mvm: BT Coex add support for Co-running block
7265 features a new calibration which is called antenna
coupling. The purpose of this calibration (which isn't
really a calibration), is to measure the isolation between
the antennas and that can give us useful information for
the Coex modules.

With this information, we can tune the LookUpTables (LUTs)
that define the BT / WiFi contention policy.

The LUTs currently contain dummy values - but they will be
updated soon.

While at it, change the current code to stop duplicate the
host command while sending. This was needed back then, when
the command was short enough to be allocated on the stack.
Since then, the command grew a lot and is now allocated on
the heap - hence we can use the NOCOPY option instead.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-03-11 19:46:47 +02:00
Emmanuel Grumbach 741e703b58 iwlwifi: mvm: BT Coex - fix SYNC2SCO flags
The Sync to SCO is a feature that allows to synchronize
between the WiFi traffic and the expectable BT traffic
when SCO profile is active.
We need to set the validity bit in the command in the init
flow, and set / clear the enablement bit if we want to
enabled / disable the feature.

While at it, clean up the flags that are not used in the
API.

This feature needs to be enabled / disabled easily, so
export its enablement to constants.h.

Reviewed-by: Eyal Zolotov <eyal.zolotov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-02-03 22:43:51 +02:00
Johannes Berg 1fb184b4a4 iwlwifi: mvm: limit non-low-latency binding scheduling duration
Limit the scheduling duration of bindings without a low-latency
interface in the firmware, this prevents those bindings from
occupying the medium for a period of time longer than what we
want for the other interfaces in low-latency mode.

As older firmware doesn't do anything with the max_duration field
and ignores it completely, there's no need for a firmware flag.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-02-03 22:23:35 +02:00
Johannes Berg 6ca40d6eae iwlwifi: mvm: reserve bandwidth for low-latency interface
If there is/are interface(s) in low-latency mode, reserve a
percentage (currently 64%) of the quota for that binding to
improve the quality of service for those interfaces. However,
if there's more than one binding that has low-latency, then
give up and don't reserve, we can't allocate more than 100%.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-02-03 22:23:35 +02:00
Emmanuel Grumbach 51368bf792 iwlwifi: Update Copyright to 2014
Happy new year!

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-31 19:03:53 +02:00
Alexander Bondar b34b912f2c iwlwifi: mvm: Adjust some power management constants
Adjust the following:

- RX/TX AP-to-PSM timeout in case of uAPSD and PBW snoozing
- PSM-to-AM TX/RX heavy traffic thresholds
- Beacon abort escape timer for D3/D0i3

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-10-02 18:00:35 +02:00
Alexander Bondar 8971634480 iwlwifi: mvm: Add PBW snoozing enablement
The Performance Based Window snooze mechanism is based on uAPSD and is
used in low-medium traffic scenarios, in order to provide better power
performance while insuring low latency and jitter for the incoming traffic.
This patch enables PBW snoozing in case uAPSD is enabled and all ACs are
uAPSD trigger and delivery enabled.

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-08-16 12:13:28 +02:00
Alexander Bondar e3c588ec0d iwlwifi: mvm: Add basic uAPSD client support
Implement basic uAPSD client support adding the following:

- Advertise uAPSD support in HW capabilities
- Set all ACs trigger- and delivery-enabled
- Set max SP length to 2 buffered frames
- Assign QNDP with the highest TID with no mandatory admission
  control required
- Set uAPSD related parameters in Power Table command

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-08-12 15:23:05 +02:00
Johannes Berg 99545924a1 iwlwifi: mvm: split constants into separate file
To make maintaining some constant default values in the
driver easier, declare them in a separate file.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31 11:05:02 +02:00