This converts all the Wolfson drivers using this format (the only devices
that do) except WM8753 to use it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While writes tend to be able to use a fairly bus independant format to
do the writes reads are all bus specific. To allow us to factor out
this code include the bus type as a parameter when setting up the
cache.
Initially just use this to factor out hw_write_t for I2C.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A lot of CODECs share the same register data formats and therefore
replicate the code to manage access to and caching of the register
map. In order to reduce code duplication centralised versions of
this code will be introduced with drivers able to configure the use
of the common code by calling the new snd_soc_codec_set_cache_io()
API call during startup.
As an initial user the 7 bit address/9 bit data format used by many
Wolfson devices is supported for write only CODECs and the drivers
with straightforward register cache implementations are converted to
use it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Unsigned variables should use `%u' rather than `%d'.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Merge Eric Maio's patch to merge snd_soc_dai_ops out of line. Fixed
merge issues and updated drivers, plus an issue with the ops for the two
s3c2443 AC97 DAIs having been merged.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Considering the fact that most cpu_dai or codec_dai are using a same
'snd_soc_dai_ops' for several similar interfaces, 'ops' would be better
made a pointer instead, to make sharing easier and code a bit cleaner.
The patch below is rather preliminary since the asoc tree is being
actively developed, and this touches almost every piece of code,
(and possibly many others in development need to be changed as
well). Building of all codecs are OK, yet to every SoC, I didn't test
that.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When setting WM8510_MCLKDIV the pll was turned off.
When setting pll frequency you got twice the expected freq, because
the code calculated with postscaler of 8, but the hardware divide by 4.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many codec drivers were implementing cookie-cutter copies of the function
that adds kcontrols to the codec.
This patch moves this code to a common function snd_soc_add_controls() in
soc-core.c and updates all drivers using copies of this function to use the
new common version.
[Edited to raise priority of error log message and document parameters.
-- broonie]
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently this is done at module probe time since ASoC ties in codec
device probe to the instantiation of the entire ASoC device. Subsequent
patches will refactor the codec drivers to handle probing separately.
Note that the core does not yet use this information.
AC97 is special since the codec is controlled over the AC97 link but
we want to give the machine driver a chance to set up the system before
trying to instantiate since it may need to do configuration before the
AC97 link will operate
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently ASoC card initialisation is completed by a function called
snd_soc_register_card(). As part of the work to allow independant
registration of cards, codecs and machines in ASoC v2 a new function of
the same name has been added so rename the existing function to
facilitate the merge of v2.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Liam Girdwood's ASoC v2 work avoids having two different ops structures
for DAIs by merging the members of struct snd_soc_ops into struct
snd_soc_dai_ops, allowing per DAI configuration for everything.
Backport this change.
This paves the way for future work allowing any combination of DAIs to
be connected rather than having fixed purpose CODEC and CPU DAIs and
only allowing CODEC<->CPU interconnections.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update the contact information for Liam Girdwood in ASoC core and
drivers as my old email address is no longer valid.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8510 microphone input PGA was represented as a DAPM PGA but in
DAPM terms the functionality is that of a mixer since it takes three
switchable inputs and produces one output. Representing it as an input
was causing its controls to be misinterpreted as gain controls and
would cause some required DAPM updates to be missed.
Reported-by: Jukka Hynninen <ext-jukka.hynninen@vaisala.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8510 bias level configuration blindly overwrites the power
management registers, interfering with the operation of DAPM.
Only adjust the specific bits required, implementing use of the VMID
resistor string configuration control as we go.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implement SPI support for WM8510, cut'n'pasting from the support for
WM8731 contributed by Cliff Cai and Alan Horstmann since the wire format
is the same for both codecs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mic PGA Switch should be inverted in the WM8510 driver but isn't.
Reported-by: ext-jukka.hynninen@vaisala.com
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Convert the wm8510 codec driver to the new (standard) device
driver binding model.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Geoffrey Wossum <gwossum@acm.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Many SoC audio codec drivers have improper freeing of memory in error
paths.
* codec is allocated in the platform device probe function, but is not
freed there in case of error. Instead it is freed in the i2c device
probe function's error path. However the success or failure of both
functions is not linked, so this could result in a double free (if
the platform device is successfully probed, the i2c device probing
fails and then the platform driver is unregistered.)
* codec->private_data is allocated in many platform device probe
functions but not freed in their error paths.
This patch hopefully solves all these problems.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch merges struct snd_soc_codec_dai and struct
snd_soc_cpu_dai into struct snd_soc_dai for the codec drivers.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Several ASoC codec drivers use custom macros equivalent to the standard
pr_ macros, most of which are not actually used. Replace these custom
macros with the standard ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The WM8510 is a mono CODEC with speaker driver optimised for telephony
applications, featuring:
- 16/20/24/32 bit audio at data rates between 8kHz and 48kHz
- On-chip PLL
- Dual microphone inputs
This driver was originally written by Liam Girdwood with updates from
Brett Saunders, Geoffrey Wossum and myself.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Brett Saunders <breton.saunders@ntlworld.com>
Signed-off-by: Geoffrey Wossum <geoffrey@pager.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mark Brown