For OMAP3 add MMC1 MMC2 pin mux MMC3 mux is not added as there are
multiple configurations possible, so the muxing is left to be done
in board file.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Chikkature Rajashekar <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables to peek the following data.
$ /debug/iommu/isp# ls
mem nr_tlb_entries regs
mmap pagetable tlb
$ /debug/iommu/isp# head pagetable
L: da: pa:
-----------------------------------------
2: 00001000 8ae4a002
2: 00002000 8e7bb002
2: 00003000 8ae49002
2: 00004000 8ae65002
.....
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add board file for Nokia N800 and N810 devices. Currently only serial ports,
onenand and spi are configured, more to come later.
Tested on Nokia N800.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For some reason usb-tusb6010.c was't compiled, add it to Makefile and
Kconfig. This is prepraration for upcoming n8x0 support.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP tags are deprecrated so drop them.
Drop UART config data which decides which UARTs to enable during boot.
This is no longer necessary since serial core code disables clocks
after inactivity.
Background: with new UART idle code, all on-chip UARTs are idled using
a configurable inactivity timer (default 5 seconds.) After the
inactivity timer, UART clocks are disabled automatically.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Search and replace OMAP_IO_ADDRESS with OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS,
and convert omap_read/write into a functions instead of a macros.
Also rename OMAP_MPUIO_VBASE to OMAP1_MPUIO_VBASE.
In the long run, most code should use ioremap + __raw_read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
twl_mmc_cleanup() must free up the regulators that were
allocated by twl_mmc_late_init().
This eliminates the below error when 'omap_hsmmc' module is
repeatedly loaded and unloaded.
"sysfs: cannot create duplicate filename '/devices/platform
/mmci-omap-hs.0/microamps_requested_vmmc'"
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OTG transceiver to RX51 platform data to prevent kernel NULL pointer
dereference during MUSB initialisation.
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes a wrong setting of resource parameter list in
SMSC911x platform driver data structure for Overo case.
This fixes folowing warning when compiling for Overo board:
warning: initialization from incompatible pointer type
Introduced since commit id:
commit 172ef27544
Author: Steve Sakoman <sakoman@gmail.com>
Date: Mon Feb 2 06:27:49 2009 +0000
ARM: Add SMSC911X support to Overo platform (V2)
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3EVM uses ISP1504 phy which doesn't require any programming and
thus has to use NOP otg transceiver.
Cleanups being done:
- Remove unwanted code in usb-musb.c file
- Register NOP in OMAP3EVM board file using
usb_nop_xceiv_register().
- Select NOP_USB_XCEIV for OMAP3EVM boards.
- Don't enable TWL4030_USB in omap3_evm_defconfig
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Eino-Ville Talvala <talvala@stanford.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Powerdomain previous state is checked after restoring new states in
suspend. This patch fixes this problem.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Use list_add_tail() when adding discovered UART ports. This is so
traversal using list_for_each_entry() will traverse the list in the
order they were found.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch causes the OMAP uarts to honor the sysfs power/wakeup file
for IOPAD wakeups. Before the OMAP was always woken up from off mode
on a rs232 signal change. This patch also creates a different
platform device for each serial port so that the wakeup properties can
be control per port.
By default, IOPAD wakeups are enabled for each UART. To disable,
# echo disabled > /sys/devices/platform/serial8250.0/power/wakeup
Where serial8250.0 can be replaced by .1, or .2 to control the other
ports.
Original idea and original patch from Russ Dill <russ.dill@gmail.com>
Cc: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
It was possible for an unhandled interrupt to occur if there was incoming
serial traffic during wakeup from suspend. This was caused by the code
in arch-arm/mach-omap2/serial.c keeping interrupt enabled all the time,
but not acking its interrupts. Applies on top of PM branch.
Use the PM begin/end hooks to ensure that the "serial idle" interrupts
are disabled during the suspend path. Also, since begin/end hooks are
now used, use the suspend_state that is passed in the begin hook instead
of the enter hook as per the platform_suspend_ops docs.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Streamline the OMAP4 special IRQ assignments by putting inside
normal init loop instead of having a separate loop.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
By default, prevent functional wakeups from inside a module from
waking up the IVA2. Let DSP Bridge code handle this when loaded.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
fix the following 'make includecheck' warning:
arch/arm/mach-omap2/mcbsp.c: mach/irqs.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix two bugs in the OMAP3 clock tree pertaining to the SSI, DSS,
USBHOST, and HSOTGUSB devices. These devices are both interconnect
initiators and targets. Without this patch, clk_enable()s on clocks for
these modules can be very high latency (potentially up to ~200
milliseconds) and message such as the following are generated:
Clock usbhost_48m_fck didn't enable in 100000 tries
Two bugs are fixed by this patch. First, OMAP hardware only supports
target CM_IDLEST register bits on ES2+ chips and beyond. ES1 chips
should not wait for these clocks to enable. So, split the appropriate
clocks into ES1 and ES2+ variants, so that kernels running on ES1
devices won't try to wait.
Second, the current heuristic in omap2_clk_dflt_find_idlest() will
fail for these clocks. It assumes that the CM_IDLEST bit to wait upon
is the same as the CM_*CLKEN bit, which is false[1]. Fix by
implementing custom clkops .find_idlest function pointers for the
appropriate clocks that return the correct slave IDLEST bit shift.
This was originally fixed in the linux-omap kernel during 2.6.29 in a
slightly different manner[2][3].
In the medium-term future, all of the module IDLEST code will
eventually be moved to the omap_hwmod code.
Problem reported by Jarkko Nikula <jhnikula@gmail.com>:
http://marc.info/?l=linux-omap&m=124306184903679&w=2
...
1. See for example 34xx TRM Revision P Table 4-213 and 4-217 (for the
DSS case).
2. http://www.spinics.net/lists/linux-omap/msg05512.html et seq.
3. http://lkml.indiana.edu/hypermail/linux/kernel/0901.3/01498.html
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the CM_*CLKEN bits
are in CM_{I,F}CLKEN2_CORE [1]. Fix by implementing a custom clkops
.find_idlest function to return the correct slave IDLEST register.
...
1. OMAP2430 Multimedia Device Package-on-Package (POP) Silicon Revision 2.1
(Rev. V) Technical Reference Manual, tables 4-99 and 4-105.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some OMAP2/3 hardware modules have CM_IDLEST attributes that are not
handled by the current omap2_wait_clock_ready() code. In preparation
for patches that fix the unusual devices, rename the function
omap2_wait_clock_ready() to omap2_wait_module_ready() and split it
into three parts:
1. A clkops-specific companion clock return function (by default,
omap2_clk_dflt_find_companion())
2. A clkops-specific CM_IDLEST register address and bit shift return
function (by default, omap2_clk_dflt_find_idlest())
3. Code to wait for the CM to indicate that the module is ready
(omap2_cm_wait_idlest())
Clocks can now specify their own custom find_companion() and find_idlest()
functions; used in subsequent patches.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The clock stabilization delay post a M2 divider change is needed
even before a SDRC interface clock re-enable and not only before
jumping back to SDRAM.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch fixes a bug in the CORE dpll scaling sequence which was
errouneously clearing some bits in the SDRC DLLA CTRL register and
hence causing a freeze. The issue was observed only on platforms
which scale CORE dpll to < 83Mhz and hence program the DLL in fixed
delay mode.
Issue reported by Limei Wang <E12499@motorola.com>, with debugging
assistance from Richard Woodruff <r-woodruff2@ti.com> and Girish
Ghongdemath <girishsg@ti.com>.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Limei Wang <E12499@motorola.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Girish Ghongdemath <girishsg@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: updated patch description to include collaboration credits]
Stop setting SDRC_POWER.PWDENA on boot. There is a nasty erratum
(34xx erratum 1.150) that can cause memory corruption if PWDENA is
enabled.
Based originally on a patch from Samu P. Onkalo <samu.p.onkalo@nokia.com>.
Tested on BeagleBoard rev C2.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Samu P. Onkalo <samu.p.onkalo@nokia.com>
This patches ensures the MUX settings are correct for the SDRC
CKE signals to SDRAM. This allows the self-refresh to work when
2 chip-selects are in use.
A warning is thrown away in case the initial muxing is incorrect,
in order to track faulty or old-dated bootloaders.
Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options
must be enabled for the mux code to have effect.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.
This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS
Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers
Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use async timings when sync timings are not requested.
Also ensure that OneNAND is in async mode when async
timings are used.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap_type() function is added and returns the DEVICETYPE field of
the CONTROL_STATUS register. The result can be used for conditional
code based on whether device is GP (general purpose), EMU or
HS (high security). Also move the type defines so omap1 code
compile does not require ifdefs for sections using these defines.
This code is needed for the following fix to set the SRAM
size correctly for HS omaps. Also at least PM and watchdog
code will need this function.
Signed-off-by: Kevin Hilman <khilman@ti.deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
platform_get_irq may return -ENXIO. but struct omap_mbox mbox_dsp_info.irq
is unsigned, so the error was not noticed.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
twl_mmc23_set_power() has MMC2 twl_mmc_controller hardcoded in it, which
breaks MMC3. Find the right controller to use instead.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
with while (i++ < MAX_CLOCK_ENABLE_WAIT); i can reach MAX_CLOCK_ENABLE_WAIT + 1
after the loop, so if (i == MAX_CLOCK_ENABLE_WAIT) that's still success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Correspondence with the TI OMAP hardware team indicates that
SDRC_DLLA_CTRL.FIXEDDELAY should be initialized to 0x0f. This number
was apparently derived from process validation. This is only used
when the SDRC DLL is unlocked (e.g., SDRC clock frequency less than
83MHz).
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Program the SDRC_MR_0 register as well during SDRC clock changes.
This register allows selection of the memory CAS latency. Some SDRAM
chips, such as the Qimonda HYB18M512160AF6, have a lower CAS latency
at lower clock rates.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
When changing the SDRAM clock from 166MHz to 83MHz via the CORE DPLL M2
divider, add a short delay before returning to SDRAM to allow the SDRC
time to stabilize. Without this delay, the system is prone to random
panics upon re-entering SDRAM.
This time delay varies based on MPU frequency. At 500MHz MPU frequency at
room temperature, 64 loops seems to work okay; so add another 32 loops for
environmental and process variation.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Felipe Balbi