The trasfer timeout is fixed at 1000 ms. Reading a 4Mbyte flash over
1MHz SPI bus takes way longer than that. Calculate the timeout from the
actual time the transfer is supposed to take and multiply by 2 for good
measure.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When testing SPI without DMA I noticed that filling the FIFO on the
spi controller causes timeout.
Always leave room for one byte in the FIFO.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When using DMA, the transfer_one callback should return 1 because the
transfer hasn't finished yet.
A previous commit changed the function to return 0 when the DMA channels
were correctly prepared.
This manifested in Veyron boards with this message:
[ 1.983605] cros-ec-spi spi0.0: EC failed to respond in time
Fixes: ea98491133 ("spi: rockchip: check return value of dmaengine_prep_slave_sg")
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Before disabling the pm_runtime, we must ensure that there is no transfer
in progress nor will a new one be started. Otherwise the message pump will
fail and in the end, the process requesting the transfer will be stuck.
This behavior has been observed when transferring data from a SPI flash
with dd while removing the module on a DRA7x-evm.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the second update round for 4.7-rc1. Most of changes are
about the pending ASoC updates and fixes, including a few new
drivers. Below are some highlights:
ASoC:
- New drivers for MAX98371 and TAS5720
- SPI support for TLV320AIC32x4, along with the module split
- TDM support for STI Uniperf IPs
- Remaining topology API fixes / updates
HDA:
- A couple of Dell quirks and new Realtek codec support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uNKQ
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound updates from Takashi Iwai:
"This is the second update round for 4.7-rc1. Most of changes are
about the pending ASoC updates and fixes, including a few new drivers.
Below are some highlights:
ASoC:
- New drivers for MAX98371 and TAS5720
- SPI support for TLV320AIC32x4, along with the module split
- TDM support for STI Uniperf IPs
- Remaining topology API fixes / updates
HDA:
- A couple of Dell quirks and new Realtek codec support"
* tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (63 commits)
ALSA: hda - Fix headset mic detection problem for one Dell machine
spi: spi-ep93xx: Fix the PTR_ERR() argument
ALSA: hda/realtek - Add support for ALC295/ALC3254
ASoC: kirkwood: fix build failure
ALSA: hda - Fix headphone noise on Dell XPS 13 9360
ASoC: ak4642: Enable cache usage to fix crashes on resume
ASoC: twl6040: Disconnect AUX output pads on digital mute
ASoC: tlv320aic32x4: Properly implement the positive and negative pins into the mixers
rcar: src: skip disabled-SRC nodes
ASoC: max98371 Remove duplicate entry in max98371_reg
ASoC: twl6040: Select LPPLL during standby
ASoC: rsnd: don't use prohibited number to PDMACHCRn.SRS
ASoC: simple-card: Add pm callbacks to platform driver
ASoC: pxa: Fix module autoload for platform drivers
ASoC: topology: Fix memory leak in widget creation
ASoC: Add max98371 codec driver
ASoC: rsnd: count .probe/.remove for rsnd_mod_call()
ASoC: topology: Check size mismatch of ABI objects before parsing
ASoC: topology: Check failure to create a widget
ASoC: add support for TAS5720 digital amplifier
...
Another quiet release for SPI, almost entirely driver specific changes
with the diffstat dominated by two new drivers which are about two
thirds of it in terms of lines of code:
- New drivers for PIC32 standard and SQI controllers.
- The Cadence driver has had runtime PM support added and quite a few
fixes and cleanups.
- The flash-specific accelerated path support now has a feature query
interface.
- The pxa2xx driver has been moved to use the core DMA mapping support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXQufEAAoJECTWi3JdVIfQXeEH/3PZVHvwQBqpN6S0AunlJQoM
s1bScKYeH2ukx9iw86M/upSCOVt4TGlPrdwzcYCUYll9IJuO/ChDio7PoVlxQeJB
kYUrFi6dzE/bCNzWtrGtyvNlSDsrRccbRBhmKTFQ9DokcJHgzdzhuCuXUR6OKDDw
CxlvDrLwapzOpHIncrhh6dvv1NoZgusOTMzVQAPvLbuiH9WpdnD9MjySklIqd0XU
bp+J4J5+jyBVykOZ2MdYpXf1dRhg0c0kmKXOKuX9woiJhvBFrtZX2GfCw1MXchKZ
/obHOyD7ff+MBCY2nFN95s3rl9Vxn8IAfNWsuQvZaFK0nz1bypaQ6aXIbXXgj/8=
=QO1T
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Another quiet release for SPI, almost entirely driver specific changes
with the diffstat dominated by two new drivers which are about two
thirds of it in terms of lines of code:
- new drivers for PIC32 standard and SQI controllers
- the Cadence driver has had runtime PM support added and quite a few
fixes and cleanups
- flash-specific accelerated path support now has a feature query
interface
- the pxa2xx driver has been moved to use the core DMA mapping support"
* tag 'spi-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (48 commits)
spi: pic32-sqi: Fix linker error, undefined reference to `bad_dma_ops'
spi: dw-pci: Spelling s/paltforms/platforms/g
spi: pic32-sqi: Remove pic32_sqi_setup and pic32_sqi_cleanup
spi: Fix simple typo s/impelment/implement
spi: rockchip: potential NULL dereference on error
spi: zynqmp: disable clocks in error paths
spi: Drop unnecessary dependencies on relaxed I/O accessors
spi: qup: Add spi_master_put in remove function
spi: qup: Handle clocks in pm_runtime suspend and resume
spi: st-ssc4: Fix missing spi_master_put in spi_st_probe error paths
spi: st-ssc4: Allow compile test build
spi: omap2-mcspi: Use dma_request_chan() for requesting DMA channel
spi: davinci: Use dma_request_chan() for requesting DMA channel
spi: pic32: Fix checking return value of devm_ioremap_resource
spi: spi-fsl-dspi: Update DT binding documentation
spi: Drop duplicate code to set master->dev.parent
spi: pic32: Set proper bits_per_word_mask
spi: return error if kmap'd buffers passed to spi_map_buf()
spi: core: add hook flash_read_supported to spi_master
spi: pic32-sqi: silence array overflow warning
...
PTR_ERR should access the value just tested by IS_ERR.
The semantic patch that makes this change is available
in scripts/coccinelle/tests/odd_ptr_err.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
Even if DMA support is disabled code using DMA mapping APIs compiles fine,
but fails in linking.
-------
drivers/built-in.o: In function `ring_desc_ring_free':
spi-pic32-sqi.c:(.text+0x2cfbe0): undefined reference to `bad_dma_ops'
spi-pic32-sqi.c:(.text+0x2cfbe4): undefined reference to `bad_dma_ops'
drivers/built-in.o: In function `pic32_sqi_probe':
spi-pic32-sqi.c:(.text+0x2cfe48): undefined reference to `bad_dma_ops'
spi-pic32-sqi.c:(.text+0x2cfeb0): undefined reference to `bad_dma_ops'
spi-pic32-sqi.c:(.text+0x2cff38): undefined reference to `bad_dma_ops'
--------
Correct dependency by adding 'depends on HAS_DMA' in Kconfig.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code does not use ctldata at all, so remove spi_set_ctldata call.
spi_setup() will set spi->bits_per_word = 8 if it was not set, so remove
!spi->max_speed_hz checking.
The spi core allows absent of spi->max_speed_hz setting, if it was not set
spi_setup() assigns spi->master->max_speed_hz to it.
spi core allows spi->max_speed_hz > spi->master->max_speed_hz, in this case
spi core will limit the transfer speed to ensure xfer->speed_hz won't
greater than spi->master->max_speed_hz so remove checking if
spi->max_speed_hz is higher than spi->master->max_speed_hz.
As a result, both pic32_sqi_setup() and pic32_sqi_cleanup() can be removed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes a simple typo in one of the comments.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We were calling dma_release_channel(rs->dma_tx.ch) when "rs->dma_tx.ch"
is potentially NULL. There is actually a call to that in the unwind
code at the bottom of the function so we can just re-arrange this a bit
and remove the call. Also there is no need to set rs->dma_tx.ch to
NULL on this error path.
Fixes: e4c0e06f94 ('spi: rockchip: fix probe deferral handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The if pclk enable fails the refclk is not disabled.
Fix the same.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The relaxed I/O accessors are available on all architectures now.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Release memory allocated for spi master by calling spi_master_put in
.remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clocks must ne disabled in pm_runtime to achieve some power saving.
Enable the clocks when the device is runtime resumed during a transfer.
Signed-off-by: Pramod Gurav <pramod.gurav@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no build dependency for this driver, so enable COMPILE_TEST to get
better build coverage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the new dma_request_chan() the client driver does not need to look for
the DMA resource and it does not need to pass filter_fn anymore.
By switching to the new API the driver can now support deferred probing
against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the new dma_request_chan() the client driver does not need to look for
the DMA resource and it does not need to pass filter_fn anymore.
By switching to the new API the driver can now support deferred probing
against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_ioremap_resource() returns ERR_PTR on error.
Also remove the redundant dev_err message, the implementation of
devm_ioremap_resource() already print error messages on error paths.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver only supports 8/16/32 bits_per_word, so set
master->bits_per_word_mask accordingly. With this change, we can remove
the spi->bits_per_word checking in pic32_spi_setup as it's done by spi
core.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Certain Intel Sunrisepoint PCH variants report zero chip selects in SPI
capabilities register even they have one per port. Detection in
pxa2xx_spi_probe() sets master->num_chipselect to 0 leading to -EINVAL
from spi_register_master() where chip select count is validated.
Fix this by not using SPI capabilities register on Sunrisepoint. They don't
have more than one chip select so use the default value 1 instead of
detection.
Fixes: 8b136baa58 ("spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Current spi_map_buf() implementation supports creates sg_table for
vmalloc'd and kmalloc'd buffers. Therefore return error if kmap'd buffer
(or any other buffer) is passed to spi_map_buf().
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We read one element beyond the end of the array when we access
"rdesc[i + 1]" so it causes a static checker warning. It's harmless
because we write over it again on the next line. But let's just silence
the warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI controller managed by the spi-orion is used on the new ARM64
Marvell Armada 7K/8K SoCs. In order to allow this driver to be built
for this platform, we allow it to be selected for ARCH_MVEBU=y
configurations.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver implements SPI master interface for Quad SPI
controller, specifically for accessing quad SPI flash.
It uses descriptor-based DMA transfer mode and supports
half-duplex communication for single, dual and quad SPI
transactions.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This implements more efficient reads of SPI-attached flash content.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The newly added runtime PM support for the cadence spi driver
causes harmless warnings when PM is disabled:
drivers/spi/spi-cadence.c:681:12: warning: 'cnds_runtime_suspend' defined but not used
drivers/spi/spi-cadence.c:652:12: warning: 'cnds_runtime_resume' defined but not used
This adds __maybe_unused annotations to the respective functions
to shut up the warnings, while leaving the code in place for
compile testing and avoiding ugly #ifdefs.
Fixes: d36ccd9f7e ("spi: cadence: Runtime pm adaptation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows defining SPI devices connected to a DLN2 using devicetree.
This already works for i2c because of a similar patch:
3b10db23: i2c: dln2: set the device tree node of the adapter
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Acked-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The source and destination masters are reflecting buses or their layers to
where the different devices can be connected. The patch changes the master
names to reflect which one is related to which independently on the transfer
direction.
The outcome of the change is that the memory data width is now always limited
by a data width of the master which is dedicated to communicate to memory.
The patch will not break anything since all current users have the same data
width for all masters. Though it would be nice to revisit avr32 platforms to
check what is the actual hardware topology in use there. It seems that it has
one bus and two masters on it as stated by Table 8-2, that's why everything
works independently on the master in use. The purpose of the sequential patch
is to fix the driver for configuration of more than one bus.
The change is done in the assumption that src_master and dst_master are
reflecting a connection to the memory and peripheral correspondently on avr32
and otherwise on the rest.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We clamp frame_len_words to a maximum of 4096, but do not actually
limit the number of words written or read through the DATA registers
or the length added to spi_message::actual_length. This results in
silent data corruption for commands longer than this maximum.
Recalculate the length of each transfer, taking frame_len_words into
account. Use this length in qspi_{read,write}_msg(), and to increment
spi_message::actual_length.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Each transfer can specify 8, 16 or 32 bits per word independently of
the default for the device being addressed. However, currently we
calculate the number of words in the frame assuming that the word size
is the device default.
If multiple transfers in the same message have differing
bits_per_word, we bitwise-or the different values in the WLEN register
field.
Fix both of these. Also rename 'frame_length' to 'frame_len_words' to
make clear that it's not a byte count like spi_message::frame_length.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Let all SPI masters ignore their children: when it comes
to power management: SPI children have no business doing
keeping their parents awake: they are completely autonomous
devices that just use their parent to talk, and the latter
usecase must be power managed by the host itself on a
per-message basis.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 3525e0aac9.
The DMA transfer for RX buffer was not handled correctly in this change.
The actual transfer length for DMA RX can be less than xfer->len in the
specific condition and the last words will be filled after the DMA
completion, but the commit doesn't consider it and the dmaengine is
started with rx_sg mapped by spi core.
The solution for this at least requires more lines than this commit
has inserted. So revert it for now.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No functional change.
Fixing some style related issues
CHECK: multiple assignments should be avoided
+ new_ctrl_reg = ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR);
CHECK: Alignment should match open parenthesis
+static void cdns_spi_config_clock_freq(struct spi_device *spi,
+ struct spi_transfer *transfer)
CHECK: Please use a blank line after function/struct/union/enum declarations
+}
+static int cdns_prepare_message(struct spi_master *master,
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are use cases when chip select should be triggered between transfers
in single SPI message. Current implementation does this only on last
transfer in message ignoring cs_change value provided in current transfer.
Signed-off-by: Andrey Vostrikov <andrey.vostrikov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown