Add a function that can be used to add the default mode for the output device
without EDID.
It will add the default mode that meets with the requirements of given
hdisplay/vdisplay limit.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we need to add the standard timing mode, we will firstly check whether it
can be found in DMT table by comparing the hdisplay/vdisplay/vfresh_rate.
If it can't be found, then we will use the cvt/gtf to add the required mode.
If it can be found, it will be returned.
At the same time the function of drm_mode_vrefresh is also fixed. It will
return the result of actual refresh_rate plus 0.5.
For example:
When the calculated value is 84.9, then the fresh_rate is 85.
When the calculated value is 70.02, then the fresh_rate is 70.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we add a standard timing mode in UMS, we will first check whether it can
be found in default mode table. If it can't be found, then we will use cvt/gtf
to add the standard timing mode.
Add the default mode table so that we can check whether the given mode
can be found in the default mode table as what we have done in UMS mode.
If the status of one output device is connected but there is no EDID, it will
have no correct mode. In such case we can add some default modes for it. Of
course we only add the modes in the default modes list that visible part is not
greater than 1024x768.
The default mode is autogenerated from the DMT spec. And it is copied from
xserver/hw/xfree86/modes/xf86EdidModes.c. But the mode with reduced blank
feature is removed.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds some rv350+ register for LTE/GTE discard,
and enables the rv515 two sided stencil register.
It also disables the DEPTHXY_OFFSET register which
can be used to workaround the CS checker.
Moves rs690 to proper place in rs600 and uses correct
table on rs600.
Signed-off-by: Dave Airlie <airlied@redhat.com>
According to the docs, the ringbuffer is not allowed to wrap in the middle
of an instruction.
G45 PRM, Vol 1b, p101:
While the “free space” wrap may allow commands to be wrapped around the
end of the Ring Buffer, the wrap should only occur between commands.
Padding (with NOP) may be required to follow this restriction.
Do as commanded.
[Having seen bug reports where there is evidence of split commands, but
apparently the GPU has continued on merrily before a bizarre and untimely
death, this may or may not fix a few random hangs.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
CC: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
mac Mini's have a single DDC line on the DVI connector, shared between the
analog link and the digital link. So, if DDC isn't detected on GPIOE (the
usual SDVO DDC link), try GPIOA (the usual VGA DDC link) when there isn't a
VGA monitor connected.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
It seems that on IGDNG the same swizzling setup always applys.
And front buffer tiling needs to set address swizzle in display
arb control too.
Fix plane tricle feed setting in v1 which should be disable bit,
and always setup address swizzle to let hardware care for buffer
tiling in all cases.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
And clean up a small whitespace goof-up in the same function, while
I was looking at it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
There are several sources of unnecessary power consumption on Intel
graphics systems. The first is the LVDS clock. TFTs don't suffer from
persistence issues like CRTs, and so we can reduce the LVDS refresh rate
when the screen is idle. It will be automatically upclocked when
userspace triggers graphical activity. Beyond that, we can enable memory
self refresh. This allows the memory to go into a lower power state when
the graphics are idle. Finally, we can drop some clocks on the gpu
itself. All of these things can be reenabled between frames when GPU
activity is triggered, and so there should be no user visible graphical
changes.
Signed-off-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In the event that any one of the DAC analog outputs (R,G,B) were driven
at full-scale (white video) or some analog level close to full-scale
voltage, and if the video cable were then disconnected, the analog video
voltage level would exceed the maximum electrical overstress limit of the
native (thin-oxide) transistors thus causing a long-term reliability concern.
The electrical overstress condition occurs in this particular case.
This patch address the IGD EOS (electrical overstress condition) issue.
When the EOS interrupt occurs, OS should disable DAC and then disable EOS,
then the normal hotplug operation follows.
TODO: it appears the normal unplug interrupt is missed as reported by Li Peng,
need more checks here.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Currently SDVO TV only support NTSC-M format. In this patch
we introduce PAL and SECAM formats available and create seting-format
property at init time. When user dynamically chose preferred
format by xrandr command, it will refine all modelines
provided by SDVO device, then instruct SDVO device to execute.
At the same time the property is added for SDVO-TV so that the SDVO-TV mode can be changed
by using xrandr.
https://bugs.freedesktop.org/show_bug.cgi?id=22891
Signed-off-by: Ma Ling <ling.ma@intel.com>
review-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For integrated TV there are 3 connector types: S-VIDEO, Composite and
Component(YprPb). Those tv formats whose component flag is true should
be assigned to Component connector, others are for S-VIDEO and Composite.
The patch intends to find appropriate tv format for each connector.
In such case it will return the correct modeline to user space. Otherwise
it will return the incorrect modeline when S-video/composite is connected.
Signed-off-by: Ma Ling <ling.ma@intel.com>
reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add a debugfs file to dump the entire register range. Here we
assume that reading write-only/reserved registers won't make the chip
angry. Seems to hold true, thankfully.
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Remember to release the local reference if we fail to wait on
the rendering.
(Also whilst in the vicinity add some whitespace so that the phasing of
the operations is clearer.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Some i915/i945 platforms have a fairly high memory latency in certain
situations, so increase our constant a bit to avoid FIFO underruns.
The effect should be positive on other platforms as well; we'll have a
bit more insurance against a busy memory subsystem due to the extra
FIFO entries.
Fixes fdo bug #23368. Needed for 2.6.31.
Tested-by: Sven Arvidsson <sa@whiz.se>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
For shared tv-out and VGA encoders, we really need to know if
the encoder is just being switched off temporarily in blanking
or if we are really disabling it hard.
Also we need to try harder to disconnect encoders from unused
connectors so we can share more efficently.
(shared encoders stuff is coming in radeon tv-out support)
Signed-off-by: Dave Airlie <airlied@redhat.com>
This produces a warn on for architectures where this gets called
but we don't have a cache flushing implementation suitable.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds code to the drm_mm to talk to debugfs, and adds
support to radeon to add the VRAM and GTT mm lists to debugfs.
I tested with spinlock debugging and it doesn't give out.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Improve CRTDDC mapping by using VBT info
drm/i915: Fix CPU-spinning hangs related to fence usage by using an LRU.
drm/i915: Set crtc/clone mask in different output devices
drm/i915: Always use SDVO_B detect bit for SDVO output detection.
drm/i915: Fix typo that broke SVID1 in intel_sdvo_multifunc_encoder()
drm/i915: Check if BIOS enabled dual-channel LVDS on 8xx, not only on 9xx
drm/i915: Set the multiplier for SDVO on G33 platform
Set accel to none, we really don't want anyone thinking
fb is an accel interface.
Pass pitch not depth to function for intel.
Signed-off-by: Dave Airlie <airlied@redhat.com>
airlied: fixup race against drm info by filling out
tmp before adding it to proc.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Sometimes we can obtain the EDID with multiple blocks from the display device.
For example: HDMI monitor.
When the CEA-EDID block is detected, we should also parse the detailed timing
info from it. Otherwise we will lose some modes for the display device.
The first step is check whether the CEA EDID block is found. If it exists,
it will skip the CEA-data block and parse the detailed timing info.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Initially I always meant this code to be shared, but things
ran away from me before I got to it.
This refactors the i915 and radeon kms fbdev interaction layers
out into generic helpers + driver specific pieces.
It moves all the panic/sysrq enhancements to the core file,
and stores a linked list of kernel fbs. This could possibly be
improved to only store the fb which has fbcon on it for panics
etc.
radeon retains some specific codes used for a big endian
workaround.
changes:
fix oops in v1
fix freeing path for crtc_info
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Almost all r128's private ioctls require that the CCE state has
already been initialised. However, most do not test that this has
been done, and will proceed to dereference a null pointer. This may
result in a security vulnerability, since some ioctls are
unprivileged.
This adds a macro for the common initialisation test and changes all
ioctl implementations that require prior initialisation to use that
macro.
Also, r128_do_init_cce() does not test that the CCE state has not
been initialised already. Repeated initialisation may lead to a crash
or resource leak. This adds that test.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Loosely based on a patch by
Jaswinder Singh Rajput <jaswinderlinux@gmail.com>.
KMS support by Dave Airlie <airlied@redhat.com>.
For Radeon 100- to 500-series, firmware blobs look like:
struct {
__be32 datah;
__be32 datal;
} cp_ucode[256];
For Radeon 600-series, there are two separate firmware blobs:
__be32 me_ucode[PM4_UCODE_SIZE * 3];
__be32 pfp_ucode[PFP_UCODE_SIZE];
For Radeon 700-series, likewise:
__be32 me_ucode[R700_PM4_UCODE_SIZE];
__be32 pfp_ucode[R700_PFP_UCODE_SIZE];
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Previously the old encoder would be called during modeset and without a connector bad things happened.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- The previous system was not very transparent, nor flexible.
- This is needed to be able to fix a few bugs in the mechanism.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use VBT information to determine which DDC bus to use for CRTDCC.
Fall back to GPIOA if VBT info is not available.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested on: 855 (David), and 945GM, 965GM, GM45, and G45 (anholt)
Several functions in the GEM kernel API used int as handle type, but
user API has it __u32 which is also the intended type.
Replace int with u32.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Image format is IHEX, one record for each pipe in order (record
addresses are ignored).
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Based on Bspec each encoder has different sharing pipe property,
i.e. Integrated or SDVO TV both will occupy one pipe exclusively,
and sdvo-non-tv and crt are allowed to share one. The patch moves
sharing judgment into differnet output functions, and sets the right
clone bit.
This fixes both HDMI outputs choosing the same pipe.
https://bugs.freedesktop.org/show_bug.cgi?id=22247
Signed-off-by: Ma Ling <ling.ma@intel.com>
Reviewed-by : Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
After the following commit is shipped, the SDVO C detection will depend on
the SDVO_C/DP detion bit.
commit 13520b051e
Author: Kristian Høgsberg <krh@redhat.com>
Date: Fri Mar 13 15:42:14 2009 -0400
drm/i915: Read the right SDVO register when detecting SVDO/HDMI.
According to the spec we should continue to detect the SDVO_B/C based on
the SDVO_B detection bit. The new detection bit on G4X platform is for
the HDMI_C detection rather than SDVO_C detection.
https://bugs.freedesktop.org/show_bug.cgi?id=20639
Signed-off-by: Ma Ling <ling.ma@intel.com>
Acked-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit 0c2e39525b is not sufficient to
get fd.o bug #20115 fixed.
In addition intel_find_best_PLL() must not only rely on BIOS settings
for i9xx chips but also for i8xx, so drop the IS_I9XX() check.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
http://bugs.freedesktop.org/show_bug.cgi?id=21417
Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Previously we just made these offline and included them,
but no reason we can't generate them at build time.
TODO: add rs690 + r100/r200 when done.
should we do rs480/rs690 no tcl version?
Signed-off-by: Dave Airlie <airlied@redhat.com>
The drm sysfs class suspend / resume methods could not distinguish
between different device types wich could lead to illegal type casts.
Use struct device_type and make sure the class suspend / resume callbacks
are aware of those. There is no per device-type suspend / resume. Only
new-style PM.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The previous patch assumes the ioctl already existed, when
it actually didn't.
It also didn't return the correct error code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
ttm:
Fix error paths when kobject_add returns an error.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
ttm:
Remove a stray debug printout.
Remove a re-init of the lru spinlock at device init.
radeon:
Fix the size of the bo_global allocation.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Common resources, like memory accounting and swap lists should be
global and not per device. Introduce a struct ttm_bo_global to
accomodate this, and register it with sysfs. Add a small sysfs interface
to return the number of active buffer objects.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Use inclusive zones to simplify accounting and its sysfs representation.
Use DMA32 accounting where applicable.
Add a sysfs interface to make the heuristically determined limits
readable and configurable.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The device directory will be the base directory of the
sysfs representation of other ttm subsystems.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Export utility functions for drivers to add specialized devices in the
sysfs drm class subdirectory.
Initially this will be needed form TTM to add a virtual device that
handles power management.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Now that we're using the scaling property in the Intel driver I noticed
that the names were a bit confusing. I've corrected them according to
our discussion on IRC and the mailing list, though I've left out
potential new additions for a new scaling property with an integer (or
two) for the scaling factor. None of the drivers implement that today,
but if someone wants to do it, I think it could be done with the
addition of a single new type and a new property to describe the
scaling factor in the X and Y directions.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just a DRM_MASTER flag is sufficient here, though maybe this call is
totally deprecated anyway (xf86-video-intel still calls it though).
(airlied: drop ioctl auth_magic as discussed on mailing list also)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If userspace destroys a framebuffer that is in use on a crtc,
don't just null it out, tear down the crtc properly so the
hw gets turned off.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The fallback case wasn't getting executed properly if there
was no TV table, which my T42 M7 hasn't got.
Signed-off-by: Dave Airlie <airlied@redhat.com>
LVDS always requests RMX_FULL, we need to fix it so that doesn't happen
before we can enable LVDS on crtc 1.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This implements the busy ioctl along with a current domain check.
returns 0 or -EBUSY
puts the current domain no matter what the answer.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We really don't want to be doing all these indirects, updating
the GPU gart table is something we do often so the less overhead the
better.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes 3D apps timing out in the WAIT_VBLANK ioctl.
AVIVO bits compile-tested only.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this syncs the versioning check with the code the X server uses.
Reported-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Dave Airlie <airlied@redhat.com>
rs690 is r3xx 3D engine with AVIVO modesetting so we need to allow
AVIVO register for vline synchronization. This add a specific table
to rs690 to handle that. Thanks to Marc (marvin24) for debugging
this and kudos to Andre (taiu1) for spotting the origin of the bugs.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Overscan, saturation, hue. Used in the nouveau driver for GPUs with
integrated TV encoders.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The calculated vdisplay was half the right value.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some applications/hardware combinations are triggering the message "failed to
acquire vblank counter" to be issued up to 20 times a second, which makes it
both useless and dangerous, as this may hide other important messages.
This changes makes it only appear when people are debugging.
Signed-off-by: Paul Rolland <rol@as2917.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Lost-twice-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The code which takes probed modes and adds them to a connector eliminates
duplicate modes by comparing them using drm_mode_equal. That function
doesn't consider the type bits, which means that any modes which differ only
in the type field will be lost.
One of the bits in the mode->type field is the DRM_MODE_TYPE_PREFERRED bit.
If the mode with that bit is lost, then higher level code will not know
which mode to select, causing a random mode to be used instead.
This patch simply merges the two mode type bits together; that seems
reasonable to me, but perhaps only a subset of the bits should be used? None
of these can be user defined as they all come from looking at just the
hardware.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (22 commits)
drm/i915: Fix read outside array bounds in restoring the SWF10 range.
drm/i915: Use our own workqueue to avoid wedging the system along with the GPU.
drm/i915: Add support for dual-channel LVDS on 8xx.
drm/i915: Return disconnected for SDVO DVI when there's no digital EDID.
drm/i915: Choose real sdvo output according to result from detection
drm/i915: Set preferred mode for integrated TV according to TV format
drm/i915: fix 845G FIFO size & burst length
drm/i915: fix VGA detect on IGDNG
drm/i915: Add eDP support on IGDNG mobile chip
drm/i915: enable DisplayPort support on IGDNG
drm/i915: Fix channel ending action for DP aux transaction
drm/i915: fix issue in display pipe setup on IGDNG
drm/i915: disable VGA plane reliably
drm/I915: Fix offset to DVO timings in LVDS data
drm/i915: hdmi detection according by reading edid
drm/i915: correct self-refresh calculation in "everything off" case
drm/i915: handle FIFO oversubsription correctly
drm/i915: FIFO watermark calculation fixes
drm/i915: ignore lvds on AOpen Mini PC MP-915
drm/i915: Allow frame buffers up to 4096x4096 on 915/945 class hardware
...
we should align the GTT after VRAM no matter what, as we can
come back from resume and put in a different place and bad things happen.
Signed-off-by: Dave Airlie <airlied@redhat.com>
GTT object can either be cached,uncached or wc just let core ttm
pick the best mode according to how the bo driver and GTT memory
type was initialized.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
dev_priv->saveSWF1 is a 16 element array, but this reads up to index 22,
and restored values from the wrong registers.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Namely "brightness", "contrast" and "flicker reduction".
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The existing TV connector types are often unsuitable either because
there is no way to probe them until they're actually plugged in or
because they can change during run time (e.g. 7-pin DIN connectors
that behave as S-Video, Component, Composite or SCART depending on the
adaptor plugged in).
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Define some helper functions to make easier to detach a KMS encoder
implementation from the drm module of the GPU it's used in. This is
mainly useful for some external I2C encoders known to be present on
cards with GPUs from several different manufacturers.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add the debug info in generic drm mode by using DRM_DEBUG_KMS
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Two macro definitions of DRM_DEBUG_KMS/MODE can be used to add the debug
info related with KMS. It is confusing.
So remove the macro definition of DRM_DEBUG_MODE. Instead it can be replaced
by the DRM_DEBUG_KMS.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We will have to add a prefix when using the macro defintion of DRM_DEBUG_KMS
/DRM_DEBUG_DRIVER/MODE. It is not convenient. We should use the DRM_NAME
as default prefix.
So remove the prefix in the macro definition of DRM_DEBUG_KMS/DRIVER/MODE.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check whether index is within bounds before grabbing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check whether index is within bounds before grabbing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If there are multiple simultaneous waiters for the same buffer object,
a temporary reference to its sync object may be leaked.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On some architectures the comparison may cause a compilation failure.
Original partial fix Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This was caught by Weiss. Also added some comments to the
fb_changed and mode_changed variables to explain what they do.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Tested-by: Thomas White <taw@bitwiz.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Match the logic to the comments in the debug message
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This corresponds to a fix to UMS back in 2007. Fixes fd.o bug #20115.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The patch fixed a bug on MP965-D. When VGA is connected to a DVI-I connector,
it incorrectly shows sdvo dvi as connected.
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: hand-resolved against previous commit and fixed up commit message]
Signed-off-by: Eric Anholt <eric@anholt.net>
Baed on Eric's idea in order to handle multiple sdvo encoders
we implement another approach to dynamically chose real one
encoder after detection, which is contrasted with patch -
drm/i915:Construct all possible sdvo outputs for sdvo encoder.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In order to get best possible quality image we chose 640x480 for
NTSC, PAL and 480p, 1280x720 for 720p, 1920x1080 for 1080i/p
TV format respectively.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
I had one report of flicker due to FIFO underruns on 845G. Scott was
kind enough to test a few patches and report success with this one.
Looks like 845G measures FIFO size slightly differently than other
chips, and we were also clobbering the FIFO burst length. Fixing both
of those issues gives him a healthy machine again.
Note that we still only adjust plane A's watermark in the 830/845
case. If someone is willing to test we could support a bigger variety
of dual-head 830/845 configurations with a bit more code.
Fixes fdo bug #19304 (again).
Reported-by: Scott Hansen <scottandchrystie@comcast.net>
Tested-by: Scott Hansen <scottandchrystie@comcast.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Check FORCE_DETECT bit to be clear for the finish
of hotplug detect process. Also check possible mono
monitor which should also be marked as connected.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds embedded DisplayPort support on next mobile chip which
aims to replace origin LVDS port. VBT's driver feature block has
been used to determine the type of current internal panel for eDP
or LVDS.
Currently no panel fitting support for eDP and backlight control
would be added in future.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We should use current channel 'status' bits to clear DP aux channel's
done and error bits, instead of using the channel setting bits, that
will set send/busy bit again to initiate new transaction.
This also includes also some minor cleanup.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
During pipe DPMS off, instead of busy waiting pipe off, insert
delays during wait and don't loop after enough tries which matches
spec requirement. Also try to match DPMS on path by disable FDI TX
PLL in DPMS off. Disable PF by writing PF_WIN_SZ which really trigger
the update.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This does VGA disable like DDX driver. SR01 bit 5 should be set
before VGA plane disable through control register, otherwise we
might get random crash and lockups.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Now the DVO timing in LVDS data entry is obtained by using the
following step:
a. get the entry size for every LVDS panel data
b. Get the LVDS fp entry for the preferred panel type
c. get the DVO timing by using entry->dvo_timing
In our driver the entry->dvo_timing is related with the size of
lvds_fp_timing. For example: the size is 46.
But it seems that the size of lvds_fp_timing varies on the differnt
platform. In such case we will get the incorrect DVO timing entry
because of the incorrect DVO offset in LVDS panel data entry.
This also removes a hack on new IGDNG to get proper DVO timing.
Calculate the DVO timing offset in LVDS data entry to get the DVO timing
a. get the DVO timing offset in the LVDS fp data entry by using the
pointer definition in LVDS data ptr
b. get the LVDS data entry
c. get the DVO timing by adding the DVO timing offset to data entry
https://bugs.freedesktop.org/show_bug.cgi?id=22787
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-radeon-kms' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (35 commits)
drm/radeon: set fb aperture sizes for framebuffer handoff.
drm/ttm: fix highuser vs dma32 confusion.
drm/radeon: Fix size used for benchmarking BO copies.
drm/radeon: Add radeon.test parameter for running BO GPU copy tests.
drm/radeon/kms: allow interruptible waits for objects.
drm/ttm: powerpc: Fix Highmem cache flushing.
x86: Export kmap_atomic_prot() needed for TTM.
drm/ttm: Fix ttm in-kernel copying of pages with non-standard caching attributes.
drm/ttm: Fix an oops and sync object leak.
drm/radeon/kms: vram sizing on certain r100 chips needs workaround.
drm/radeon: Pay more attention to object placement requested by userspace.
drm/radeon: Fall back to evicting BOs with memcpy if necessary.
drm/radeon: Don't unreserve twice on failure to validate.
drm/radeon/kms: fix bandwidth computation on avivo hardware
drm/radeon/kms: add initial colortiling support.
drm/radeon/kms: fix hotspot handling on pre-avivo chips
drm/radeon/kms: enable frac fb divs on rs600/rs690/rs740
drm/radeon/kms: add PLL flag to prefer frequencies <= the target freq
drm/radeon/kms: block RN50 from using 3D engine.
drm/radeon/kms: fix VRAM sizing like DDX does it.
...
The incorrect size caused benchmark results to be inflated by a factor of 4.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If enabled, during initialization BO GTT->VRAM and VRAM->GTT GPU copies are
tested across the whole GTT aperture.
This has helped uncover the benchmark copy size bug and verify the maximum
aperture size supported by the AGP bridge in my PowerBook.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Blocking here isn't something the X server mouse appreciates,
avoid the block and let userspace retry the waits.
libdrm_radeon userspace library is also expecting EBUSY not ERESTART
Signed-off-by: Dave Airlie <airlied@redhat.com>
Temporarily maps highmem pages while flushing to get a valid virtual
address to flush.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For x86 this affected highmem pages only, since they were always kmapped
cache-coherent, and this is fixed using kmap_atomic_prot().
For other architectures that may not modify the linear kernel map we
resort to vmap() for now, since kmap_atomic_prot() generally uses the
linear kernel map for lowmem pages. This of course comes with a
performance impact and should be optimized when possible.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The code was potentially dereferencig a NULL sync object pointer.
At the same time a sync object reference was potentially leaked.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If an rn50/r100/m6/m7 GPU has < 64MB RAM, i.e. 8/16/32, the
aperture used to calculate the MC_FB_LOCATION needs to be worked
out from the CONFIG_APER_SIZE register, and not the actual vram size.
TTM VRAM size was also being initialised wrong, use actual vram size
to initialise it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously we were basically always setting the GTT and VRAM flags regardless of
what userspace requested.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise if there's no GTT space we would fail the eviction, leading to
cascaded failure.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is done later in radeon_object_list_unvalidate(). Doing it twice triggers
a BUG in TTM, rendering X on KMS unusable until reboot.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix bandwidth computation and crtc priority in memory controller
so that crtc memory request are fullfill in time to avoid display
artifact.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds new set/get tiling interfaces where the pitch
and macro/micro tiling enables can be set. Along with
a flag to decide if this object should have a surface when mapped.
The only thing we need to allocate with a mapped surface should be
the frontbuffer. Note rotate scanout shouldn't require one, and
back/depth shouldn't either, though mesa needs some fixes.
It fixes the TTM interfaces along Thomas's suggestions, and I've tested
the surface stealing code with two X servers and not seen any lockdep issues.
I've stopped tiling the fbcon frontbuffer, as I don't see there being
any advantage other than testing, I've left the testing commands in there,
just flip the fb_tiled to true in radeon_fb.c
Open: Can we integrate endian swapping in with this?
Future features:
texture tiling - need to relocate texture registers TXOFFSET* with tiling info.
This also merges Michel's cleanup surfaces regs at init time patch
even though it makes sense on its own, this patch really relies on it.
Some PowerMac firmwares set up a tiling surface at the beginning of VRAM
which messes us up otherwise.
that patch is:
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
According to investigations from windows team ,hw team,
and our test results on all 4x platofrms available
(gm45, g45b, q45, g45a, g45c, g41a, and g41), we find
currently Hot plug live status and Hot plug interrupt
detection are not reliable, sometime the results from
the two approaches are contradicts. So we chose edid
detection for hdmi output.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
If no planes are enabled, the self-refresh calculation may end up doing
a divide by zero. This patch should prevent that by making sure at
least one of the CRTCs had a valid hdisplay value.
Reported-by: Eric Anholt <eric@anholt.net>
Tested-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
If you're pushing a plane hard (i.e. you need most or all of the FIFO
entries just to cover your frame refresh latency), the watermark level
may end up being negative. So fix up the signed vs. unsigned math in
the calculation function to handle this correctly, giving all available
FIFO entries to such a configuration.
Reported-by: Eric Anholt <eric@anholt.net>
Tested-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Allows us to hit dot clocks much closer, especially on
chips with non-27 Mhz reference clocks like most IGP chips.
This fixes most flickering and blanking problems with
non-exact dot clocks on these chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is needed when using fractional feedback dividers on some IGP
chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
RN50/ES1000 is a cut-down rv100 chip used in the server market.
The 3D engine on these is either not there or unverified so refuse
any attempt to configure registers on it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Doing this like the DDX seems like the most sure fire way to avoid
having to reinvent it slowly and painfully. At the moment we keep
getting things wrong with aper vs vram, so we know the DDX does it right.
booted on PCI r100, PCIE rv370, IGP rs400.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add support for using dma32 memory on gpus that really need it.
Currently IGPs are left without DMA32 but we might need to change
that unless we can fix rs690.
Signed-off-by: Dave Airlie <airlied@redhat.com>
For now handle it via r/g/b offsets and disallow 16 bpp modes on big endian
machines.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On powerpc, since we aren't using any hw swappers, this will
get flipped around by default in hw.
tested on a G5 + rv515.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Noticed by Rafał Miłecki on dri-devel. On r6xx/r7xx hardware, laptop
panels can be driven by KLDSCP_LVTMA or UNIPHY.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The line mux for the connector in the bios tables
is used for enumerating drm connectors. Since
this laptop has a quirk where the same line much is
listed for both VGA and LVDS, the connectors get
combined. Setting the line mux on LVDS to an unused
value prevents both encoders from being combined into
the same connector. This should fix bko bug 13720.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A bug caused a new caching state to be selected on each buffer object
validation regardless of the current caching state.
Moreover, a caching state could be selected that wasn't supported by
the memory type.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Userspace sends us a special relocation type to sync video/exa
to vlines to avoid tearing, this deals with the relocation
in the kernel, it picks the correct crtc and avoids issues
where crtcs are disabled.
This version also parses the wait until to make sure it isn't
trying to do anything evil.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Normally we are free to place VRAM where we want in the GPUs
memory address space, however on IGP chips the VRAM is actual RAM,
and no special translation or aperture is used inside the GPU MC.
So when you move the VRAM aperture away from the TOM register,
you actually move it into main memory and can trash things quite badly.
This commit makes the code respect the TOM location for MC_FB_LOCATION.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The crtc and cursor offsets on the legacy chips are offset from
DISPLAY_BASE_ADDR. The code worked if display base addr was at 0,
but otherwise falls to pieces.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If there is a problem then this is hiding it, we shouldn't
ever need to flush the IB. Either the buffers are:
WB - caching just works.
WC - no need to do explicit flush, the MB + readback will do it
Signed-off-by: Dave Airlie <airlied@redhat.com>
1. rv370 can accept 40-bit addresses - also at 24-bit shift not 4 bits
2. rs480 table can be in 40-bit space. - 4 bit shift for top 8 bits
3. rs480 table entries can be in 40-bit space.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the NULL test is necessary, then the dereference should be moved below
the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Create the standard timing modeline by using CVT/GFT algorithm while
interpreting the EDID.
In course of interpreting the EDID, the timing level will be obtained,
which is used to determine whether the CVT/GTF algorithm is selected to
generate the modeline for the given hdisplay/vdisplay/vrefresh_rate.
In the UMS mode firstly it will check whether it can be found in
the DMT table. If it can be found, then the modeline is returned. Then the
timing_level is used to choose CVT/GTF.
As there is no DMT table, no modeline is returned when timing level
is DMT. For the other two timing levels, the CVT/GTF will be called to
generate the required standard timing modeline.
[airlied: fixed up conflicts since EDID rework]
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Add the GTF algorithm in kernel space. And this function can be called to
generate the required modeline.
I copied it from the file of xserver/hw/xfree86/modes/xf86gtf.c. What I have
done is to translate it by using integer calculation. This is to avoid
the float-point calculation in kernel space.
At the same tie I also refer to the function of fb_get_mode in
drivers/video/fbmon.c
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Add the CVT algorithm in kernel space. And this function can be called to
generate the required modeline.
I copied it from the file of xserver/hw/xfree86/modes/xf86cvt.c. What I have
done is to translate it by using integer calculation. This is to avoid
the float-point calculation in kernel space.
[airlied:- cleaned up some bits]
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
via_enable_vblank wasn't setting the VBlank enable bit - instead, it
was masking out the rest of the register.
At the same time, fix via_disable_vblank to clear the VBlank enable
bit.
Signed-off-by: Dave Airlie <airlied@linux.ie>
Check kzalloc retval against NULL in drm_gem_object_alloc and bail out
appropriately.
While at it merge the fail paths and jump to them by gotos at the end
of the function.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Check kmalloc return value in drm_debugfs_create_files and bail out
appropriately if the pointer is NULL.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
I discovered several bugs in the FIFO code that was recently applied.
Some of them fell into the "how did this ever work" category, since in
some cases we were using the wrong FIFO size values, and the
calculations ended up being way off.
This patch fixes all the bugs I found, and works well on my GM45, 915GM
and 855GM test machines; but as usual with these sorts of patches
broader testing is definitely requested (in particular this patch
affects 830, 845 and 865 for which I don't have test hardware).
Overall, the patch clarifies the watermark calculation function by
adding some comments and debug info, and making the variable names a
bit clearer. The "get FIFO size" portion of the code has also been
corrected, so we should be able to properly detect the FIFO allocations
for each pipe, for use in the watermark calculation.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This motherboard thinks it has an LVDS connected, so without this
patch the screen goes blank on the connected VGA monitor. More
information (for the non-KMS case) in fd.o bug #18004.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The 915 and 945 scanout engines can handle frame buffers up to 4096 pixels
wide. Pre-9xx hardware has an 8192 byte stride limit, and so we leave the
existing 2048 max in place.
I'm not sure why we limit the height to the same value; there's no intrinsic
hardware limit in the scanout engine.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch refactors the existing error detection and collection code,
placing most of it in i915_handle_error(). Additionally, we introduce a
work queue for scheduling post-crash tasks such as generating a uevent.
Using the uevent facility, userspace should be able to capture a
post-mortem dump for diagnostics.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Vbios will set lvds register correctly based on
current algorithm for lingle/dual Channel LVDS when
system boot, so we can accept this configuration
directly, regardless of LVDS enable status.
It fixed freedesktop.org bug #22262
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
IGDNG mobile chip's LVDS data block removes panel fitting
register definition. So this fixes offset for LVDS timing
block parsing. Thanks for Michael Fu to catch this.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
As of 52dc7d32b8, we could leave an old
linear GTT mapping in place, so that apps trying to GTT-mapped write in
tiled data wouldn't get the fence added, and garbage would get displayed.
Signed-off-by: Eric Anholt <eric@anholt.net>
As we call unmap_mapping_range() twice in identical fashion, refactor
and attempt to explain why we need to call unmap_mapping_range().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
In KMS mode we now use the normal mode-setting paths to set the modes
back to the current configuration, so we don't need to also run the more
limited non-KMS implementation of modesetting for resume.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This is seen on some G41 systems, where the BIOS will consume all but
a few KB of the aperture. This should be bad for all operating systems, as
it means that the OS can't dynamically manage memory between graphics and
the rest of the system, and OSes that did static memory management
statically add memory in addition to the BIOS allocation anyway. So, instead
of working around it, just fail out verbosely.
fd.o bug #21574
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
On some boxes the mobile chipset is used and there is no LVDS device. In such
case we had better not initialize the LVDS output device so that one pipe can
be used for other output device. For example: E-TOP.
But unfortunately the LVDS device is still initialized on the boxes based on
mobile chipset in KMS mode. It brings that this pipe occupied by LVDS can't be
used for other output device.
After checking the acpidump we find that there is no LID device on such boxes.
In such case we can use the LID device to decide whether the LVDS device should
be initialized.
If there is no LID device, we can think that there is no LVDS device. It is
unnecessary to initialize the LVDS output device.
If there exists the LID device, it will continue the current flowchart.
Maybe on some boxes there is no LVDS device but the LID device is found. In
such case it should be added to the quirk list.
http://bugs.freedesktop.org/show_bug.cgi?id=21496http://bugs.freedesktop.org/show_bug.cgi?id=21856http://bugs.freedesktop.org/show_bug.cgi?id=21127
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: squashed in style fixups]
Signed-off-by: Eric Anholt <eric@anholt.net>
Make this consistent with the unlock statement. Also fix a
minor typo in debugfs formatting
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This is quite useful for verifying that objects are actually mapped when
they need to be.
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This wasn't even used as far as I could tell and will only confuse
people (like me).
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Usually crt mainly get modes via GPIOA ports.
However on G4X platform we need to probe possible
ports for DVI-I, which could be wired to GPIOD,
then fetch our desired EDID, i.e on DG45ID platform
we successfully fetch EDID by GPIOD port.
It fixed freedesktop.org bug #21084
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For some reason, the DP clocks were based off a 100MHz reference instead of
the standard 96MHz reference. This caused some DP monitors to fail to lock
to the signal.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Convert many printk calls to DRM_DEBUG calls to reduce kernel log noise
for normal activities. Switch other printk calls to DRM_ERROR or DRM_INFO.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We are seeing compilation failures on i386 in some environments due
to an undefined reference as below:
ERROR: "__udivdi3" [drivers/gpu/drm/i915/i915.ko] undefined!
This is generated due to a raw 64 bit divide in the i915 driver. Fix up
this raw divide.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Currently we implemented basic sdvo lvds function,
But except for sdvo lvds fixed mode, we can not switch
to other modes, otherwise display get black. The patch
handle three operations to enable sdvo lvds. At first
duplicate sdvo fixed mode for adjustment, then according
to fixed mode line valid all modes, at last adjust input
mode to fit our requirement.
Acked by Li Peng <peng.li@linux.intel.com>
Signed-off-by: Ma Ling <ling.ma@intel.com>
Reviewed-by: Ian Romanick <idr@freedesktop.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
All 8xx class chips have the 66/48 split, not just 855.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch from jbarnes and myself adds FIFO watermark control to the
driver. This is needed for both power saving features on new platforms
with the so-called "big FIFO" and for controlling FIFO allocation
between pipes in multi-head configurations.
It's also necessary infrastructure to support things like framebuffer
compression and configuration supportability checks (i.e. checking a
configuration against available bandwidth).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch enables error detection by enabling several types of error
interrupts. When an error interrupt is received, the interrupt
handler captures the error state; hopefully resulting in an accurate
set of error data (error type, active head pointer, etc.). The new
record is then available from sysfs. The current code will also dump
the error state to the system log.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (28 commits)
drm: remove unused #include <linux/version.h>'s
drm/radeon: fix driver initialization order so radeon kms can be builtin
drm: Fix shifts which were miscalculated when converting from bitfields.
drm/radeon: Clear surface registers at initialization time.
drm/radeon: Don't initialize acceleration related fields of struct fb_info.
drm/radeon: fix radeon kms framebuffer device
drm/i915: initialize fence registers to zero when loading GEM
drm/i915: Fix HDMI regression introduced in new chipset support
drm/i915: fix LFP data fetch
drm/i915: set TV detection mode when tv is already connected
drm/i915: Catch up to obj_priv->page_list rename in disabled debug code.
drm/i915: Fix size_t handling in off-by-default debug printfs
drm/i915: Don't change the blank/sync width when calculating scaled modes
drm/i915: Add support for changing LVDS panel fitting using an output property.
drm/i915: correct suspend/resume ordering
drm/i915: Add missing dependency on Intel AGP support.
drm/i915: Generate 2MHz clock for display port aux channel I/O. Retry I/O.
drm/i915: Clarify error returns from display port aux channel I/O
drm/i915: Add CLKCFG register definition
drm/i915: Split array of DAC limits into separate structures.
...
TTM need to be initialized before radeon if KMS is enabled otherwise
the kernel will crash hard.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Looks like I managed to mess up most shifts when converting from bitfields. :(
The patch below works on my Thinkpad T500 (as well as on my PowerBook,
where the previous change worked as well, maybe out of luck...). I'd
appreciate more testing and eyes looking over it though.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Tested-by: Michael Pyne <mpyne@kde.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Some PowerMac firmwares set up a tiling surface at the beginning of VRAM
which messes us up otherwise.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Might lure userspace into trying silly things otherwise.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
smem.start is a physical address which kernel can remap to access
video memory of the fb buffer. We now pin the fb buffer into vram
by doing so we are loosing vram but fbdev need to be reworked to
allow change in framebuffer address.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Sometimes both acpi video and i915 driver are compiled as modules.
And there exists the strict dependency between the two drivers.
The acpi video bus will be unloaded in course of unloading the i915 driver.
If we unload the acpi video driver, then the kernel oops will be triggered.
Add the reference count to avoid unloading the ACPI video bus twice.
The reference count should be checked before unregistering the acpi video bus.
If the reference count is already zero, it won't unregister it again.
And after the acpi video bus is already unregistered, the reference count
will be set to zero.
http://bugzilla.kernel.org/show_bug.cgi?id=13396
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Unitialized fence register could leads to corrupted display. Problem
encountered on MacBooks (revision 1 and 2), directly booting from EFI
or through BIOS emulation.
(bug #21710 at freedestop.org)
Signed-off-by: Grégoire Henry <henry@pps.jussieu.fr>
Signed-off-by: Eric Anholt <eric@anholt.net>
Remove wrongly added NULL_PACKETS_DURING_VSYNC setting for HDMI.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Apparently the proper way to do this is to use the LFP data pointer
block to figure out the LFP data block entry size, then use that plus
the panel index to calculate an offset into the LFP data block array.
Similar fix has already been pushed to the 2D driver to fix fdo bug
applied to the VBIOS reader, and things look sane).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We used load_detect_temp flag to determine whether to set tv to the test
mode. However if the TV already has a mode set, we still need to set the
test mode to determine connection. This results in blinking, but there is
no other reliable way to determine TV connection.
freedesktop.org bug #22035
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Also, use the border instead of border minus one.
At the same time, make sure the horizontal border and hsync are even for
the LVDS that works in dual-channel mode. So both horizontal border and hsync
start are also changed to be even, even for the LVDS in single-channel mode.
https://bugs.freedesktop.org/show_bug.cgi?id=20951
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Previously the driver would always scale the chosen video mode to fill the
panel. This adds 1:1 and maintain-aspect-ratio scaling modes.
v2: the drm_calloc/drm_free is replaced by kzalloc/kfree based
on Eric's suggestion.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We need to save register state *after* idling GEM, clearing the ring,
and uninstalling the IRQ handler, or we might end up saving bogus
fence regs, for one. Our restore ordering should already be correct,
since we do GEM, ring and IRQ init after restoring the last register
state, which prevents us from clobbering things.
I put this together to potentially address a bug, but I haven't heard
back if it fixes it yet. However I think it stands on its own, so I'm
sending it in.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Users could accidentally enable AGP but not the Intel AGP support, and get
a DRM that doesn't probe as a result.
Bug #22358.
Signed-off-by: Eric Anholt <eric@anholt.net>
In theory now that the AGP subsystem is using struct page, we should
have on problems enabling GEM on PAE systems.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This switches AGP to use an array of pages for tracking the
pages allocated to the GART. This should enable GEM on PAE to work
a lot better as we can pass highmem pages to the PAT code and it will
do the right thing with them.
Signed-off-by: Dave Airlie <airlied@redhat.com>
For security purpose we want to make sure the userspace process doesn't
access memory beyond buffer it owns. To achieve this we need to check
states the userspace program. For color buffer and zbuffer we check that
the clipping register will discard access beyond buffers set as color
or zbuffer. For vertex buffer we check that no vertex fetch will happen
beyond buffer end. For texture we check various texture states (number
of mipmap level, texture size, texture depth, ...) to compute the amount
of memory the texture fetcher might access.
The command stream checking impact the performances so far quick benchmark
shows an average of 3% decrease in fps of various applications. It can
be optimized a bit more by caching result of checking and thus avoid a
full recheck if no states changed since last check.
Note that this patch is still incomplete on checking side as it doesn't
check 2d rendering states.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
also for the atomic path by using a common code-path.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A bug caused the ttm code to just terminate the wait when a signal
was received while waiting for the GPU to release a buffer object that
was to be evicted.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The display port aux channel clock is taken from the hrawclk value, which is
provided to the chip as the FSB frequency (as far as I can determine). The
strapping values for that are available in the CLKCFG register, now used to
select an appropriate divider to generate a 2MHz clock.
In addition, the DisplayPort spec requires that each aux channel I/O be
retried 'at least 3 times' in case the sink is idle when the first request
comes in.
Signed-off-by: Keith Packard <keithp@keithp.com>
The array of DAC limits was only ever referenced with #defined constant
offsets, and keeping those #define values in sync with the array itself was a
nuisance. This will make future changes to the set of DAC limits less
error-prone.
Signed-off-by: Keith Packard <keithp@keithp.com>
Eliminate the copy of i2c_bus in sdvo_priv.
Eliminate local copies of i2c_bus and ddcbus.
Eliminate unused settings of slave_addr.
Signed-off-by: Keith Packard <keithp@keithp.com>
The existing API passed around intel_i2c_chan pointers, which are dependent
on the i2c bit-banging algo. This precluded the driver from using outputs
which use a different algo. Switching to the more general i2c_adpater allows
the driver to support non bit-banging DDC.
This also required moving the slave address into the output private
structures.
Signed-off-by: Keith Packard <keithp@keithp.com>
Some machines say 'Apple Inc.' while others say 'Apple Computer, Inc'.
Switch the test to just look for 'Apple' instead.
Signed-off-by: Keith Packard <keithp@keithp.com>
HDMI and DVI both require DDC/EDID on monitors, so use
that to know when a monitor is connected as the hot-plug
pins are shared with SDVO and DisplayPort
Signed-off-by: Keith Packard <keithp@keithp.com>
It hasn't been used in ages, and having the user tell your how much
memory is being freed at free time is a recipe for disaster even if it
was ever used.
Signed-off-by: Eric Anholt <eric@anholt.net>
The fence register value also depends upon the stride of the object, so we
need to clear the fence if that is changed as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[anholt: Added 8xx and 965 paths, and renamed the confusing
i915_gem_object_tiling_ok function to i915_gem_object_fence_offset_ok]
Signed-off-by: Eric Anholt <eric@anholt.net>
With the work by Jesse Barnes to eliminate allocation of fences during
execbuffer, it becomes possible to write to the scan-out buffer with it
never acquiring a fence (simply by only ever writing to the object using
tiled GPU commands and never writing to it via the GTT). So for pre-i965
chipsets which require fenced access for tiled scan-out buffers, we need
to obtain a fence register.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
After performing an operation over the page list for a buffer retrieved by
i915_gem_object_get_pages() the pages need to be returned with
i915_gem_object_put_pages(). This was not being observed for the phys
objects which were thus leaking references to their backing pages.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
CC: Dave Airlie <airlied@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
While sifting through the inteldrmfb code trying to solve #22040 I found that
the fb restore path doesn't check the return value of
drm_crtc_helper_set_config(), which seems to have all sorts of potential
failure modes. We should warn someone if one of these is triggered.
Signed-Off-By: Ben Gamari <bgamari.foss@gmail.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: hand-applied, failures are mine]
Signed-off-by: Eric Anholt <eric@anholt.net>
This causes an issue since we fixed the drm mappings to do the right thing,
so its just a copy and pasto.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: switch to using late_initcall
radeon legacy chips: tv dac bg/dac adj updates
drm/radeon: introduce kernel modesetting for radeon hardware
drm: Add the TTM GPU memory manager subsystem.
drm: Memory fragmentation from lost alignment blocks
drm/radeon: fix mobility flags on new PCI IDs.
* akpm: (182 commits)
fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
fbdev: *bfin*: fix __dev{init,exit} markings
fbdev: *bfin*: drop unnecessary calls to memset
fbdev: bfin-t350mcqb-fb: drop unused local variables
fbdev: blackfin has __raw I/O accessors, so use them in fb.h
fbdev: s1d13xxxfb: add accelerated bitblt functions
tcx: use standard fields for framebuffer physical address and length
fbdev: add support for handoff from firmware to hw framebuffers
intelfb: fix a bug when changing video timing
fbdev: use framebuffer_release() for freeing fb_info structures
radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
s3c-fb: CPUFREQ frequency scaling support
s3c-fb: fix resource releasing on error during probing
carminefb: fix possible access beyond end of carmine_modedb[]
acornfb: remove fb_mmap function
mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
mb862xxfb: restrict compliation of platform driver to PPC
Samsung SoC Framebuffer driver: add Alpha Channel support
atmel-lcdc: fix pixclock upper bound detection
offb: use framebuffer_alloc() to allocate fb_info struct
...
Manually fix up conflicts due to kmemcheck in mm/slab.c
With KMS we have ran into an issue where we really want the KMS fb driver
to be the one running the console, so panics etc can be shown by switching
out of X etc.
However with vesafb/efifb built-in, we end up with those on fb0 and the
KMS fb driver on fb1, driving the same piece of hw, so this adds an fb
info flag to denote a firmware fbdev, and adds a new aperture base/size
range which can be compared when the hw drivers are installed to see if
there is a conflict with a firmware driver, and if there is the firmware
driver is unregistered and the hw driver takes over.
It uses new aperture_base/size members instead of comparing on the fix
smem_start/length, as smem_start/length might for example only cover the
first 1MB of the PCI aperture, and we could allocate the kms fb from 8MB
into the aperture, thus they would never overlap.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Airlie <airlied@redhat.com>
Acked-by: Peter Jones <pjones@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes an issue where we get inited before fbcon when built-in.
Ideally this should work as a non late_initcall, but this fixes it for now.
We also don't suggest people build this in (at least distro maintainers).
Reported-by: Ryan Hope <rmh3093@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Many developers use "/debug/" or "/debugfs/" or "/sys/kernel/debug/"
directory name to mount debugfs filesystem for ftrace according to
./Documentation/tracers/ftrace.txt file.
And, three directory names(ex:/debug/, /debugfs/, /sys/kernel/debug/) is
existed in kernel source like ftrace, DRM, Wireless, Documentation,
Network[sky2]files to mount debugfs filesystem.
debugfs means debug filesystem for debugging easy to use by greg kroah
hartman. "/sys/kernel/debug/" name is suitable as directory name
of debugfs filesystem.
- debugfs related reference: http://lwn.net/Articles/334546/
Fix inconsistency of directory name to mount debugfs filesystem.
* From Steven Rostedt
- find_debugfs() and tracing_files() in this patch.
Signed-off-by: GeunSik Lim <geunsik.lim@samsung.com>
Acked-by : Inaky Perez-Gonzalez <inaky@linux.intel.com>
Reviewed-by : Steven Rostedt <rostedt@goodmis.org>
Reviewed-by : James Smart <james.smart@emulex.com>
CC: Jiri Kosina <trivial@kernel.org>
CC: David Airlie <airlied@linux.ie>
CC: Peter Osterlund <petero2@telia.com>
CC: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
CC: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
CC: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support to the drm core to report the proper device name to
userspace for the drm devices.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
COMBIOS - fallback to table values if there are no tv dac or lvds bios tables
ATOMBIOS - add support for looking up these values from the bios table
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add kernel modesetting support to radeon driver, use the ttm memory
manager to manage memory and DRM/GEM to provide userspace API.
In order to avoid backward compatibility issue and to allow clean
design and code the radeon kernel modesetting use different code path
than old radeon/drm driver.
When kernel modesetting is enabled the IOCTL of radeon/drm
driver are considered as invalid and an error message is printed
in the log and they return failure.
KMS enabled userspace will use new API to talk with the radeon/drm
driver. The new API provide functions to create/destroy/share/mmap
buffer object which are then managed by the kernel memory manager
(here TTM). In order to submit command to the GPU the userspace
provide a buffer holding the command stream, along this buffer
userspace have to provide a list of buffer object used by the
command stream. The kernel radeon driver will then place buffer
in GPU accessible memory and will update command stream to reflect
the position of the different buffers.
The kernel will also perform security check on command stream
provided by the user, we want to catch and forbid any illegal use
of the GPU such as DMA into random system memory or into memory
not owned by the process supplying the command stream. This part
of the code is still incomplete and this why we propose that patch
as a staging driver addition, future security might forbid current
experimental userspace to run.
This code support the following hardware : R1XX,R2XX,R3XX,R4XX,R5XX
(radeon up to X1950). Works is underway to provide support for R6XX,
R7XX and newer hardware (radeon from HD2XXX to HD4XXX).
Authors:
Jerome Glisse <jglisse@redhat.com>
Dave Airlie <airlied@redhat.com>
Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
TTM is a GPU memory manager subsystem designed for use with GPU
devices with various memory types (On-card VRAM, AGP,
PCI apertures etc.). It's essentially a helper library that assists
the DRM driver in creating and managing persistent buffer objects.
TTM manages placement of data and CPU map setup and teardown on
data movement. It can also optionally manage synchronization of
data on a per-buffer-object level.
TTM takes care to provide an always valid virtual user-space address
to a buffer object which makes user-space sub-allocation of
big buffer objects feasible.
TTM uses a fine-grained per buffer-object locking scheme, taking
care to release all relevant locks when waiting for the GPU.
Although this implies some locking overhead, it's probably a big
win for devices with multiple command submission mechanisms, since
the lock contention will be minimal.
TTM can be used with whatever user-space interface the driver
chooses, including GEM. It's used by the upcoming Radeon KMS DRM driver
and is also the GPU memory management core of various new experimental
DRM drivers.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the block needs an alignment but otherwise fits exactly into the tail,
then the split-off block from the start would remain marked as non-free.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (50 commits)
drm: include kernel list header file in hashtab header
drm: Export hash table functionality.
drm: Split out the mm declarations in a separate header. Add atomic operations.
drm/radeon: add support for RV790.
drm/radeon: add rv740 drm support.
drm_calloc_large: check right size, check integer overflow, use GFP_ZERO
drm: Eliminate magic I2C frobbing when reading EDID
drm/i915: duplicate desired mode for use by fbcon.
drm/via: vfree() no need checking before calling it
drm: Replace DRM_DEBUG with DRM_DEBUG_DRIVER in i915 driver
drm: Replace DRM_DEBUG with DRM_DEBUG_MODE in drm_mode
drm/i915: Replace DRM_DEBUG with DRM_DEBUG_KMS in intel_sdvo
drm/i915: replace DRM_DEBUG with DRM_DEBUG_KMS in intel_lvds
drm: add separate drm debugging levels
radeon: remove _DRM_DRIVER from the preadded sarea map
drm: don't associate _DRM_DRIVER maps with a master
drm: simplify kcalloc() call to kzalloc().
intelfb: fix spelling of "CLOCK"
drm: fix LOCK_TEST_WITH_RETURN macro
drm/i915: Hook connector to encoder during load detection (fixes tv/vga detect)
...
add exports so TTM module can use these functions.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this is a TTM preparation patch, it rearranges the mm and
add operations needed to do mm operations in atomic context.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This code depends on the underlying I2C adapter using the bit-banging algo,
which may not be the case. If specific encoders require this mechanism, they
should build a custom I2C algo that implements this workaround, rather than
having it in the general path.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
vfree() does it's own NULL checking, no need for explicit check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Replace the DRM_DEBUG with the DRM_DEBUG_DRIVER to print the debug info
in i915 driver.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Replace the DRM_DEBUG with DRM_DEBUG_MODE macro to print the info in drm_mode.
airlied:- fixed up to remove a conflicting #define
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the DRM_DEBUG_KMS/DEBUG_LOG_KMS to print the debug info for
SDVO device.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the DRM_DEBUG_KMS macro definition to print the debug info for
the LVDS.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now all the DRM debug info will be reported if the boot option of
"drm.debug=1" is added. Sometimes it is inconvenient to get the debug
info in KMS mode. We will get too much unrelated info.
This will separate several DRM debug levels and the debug level can be used
to print the different debug info. And the debug level is controlled by the
module parameter of drm.debug
In this patch it is divided into four debug levels;
drm_core, drm_driver, drm_kms, drm_mode.
At the same time we can get the different debug info by changing the debug
level. This can be done by adding the module parameter. Of course it can
be changed through the /sys/module/drm/parameters/debug after the system is
booted.
Four debug macro definitions are provided.
DRM_DEBUG(fmt, args...)
DRM_DEBUG_DRIVER(prefix, fmt, args...)
DRM_DEBUG_KMS(prefix, fmt, args...)
DRM_DEBUG_MODE(prefix, fmt, args...)
When the boot option of "drm.debug=4" is added, it will print the debug info
using DRM_DEBUG_KMS macro definition.
When the boot option of "drm.debug=6" is added, it will print the debug info
using DRM_DEBUG_KMS/DRM_DEBUG_DRIVER.
Sometimes we expect to print the value of an array.
For example: SDVO command,
In such case the following four DRM debug macro definitions are added:
DRM_LOG(fmt, args...)
DRM_LOG_DRIVER(fmt, args...)
DRM_LOG_KMS(fmt, args...)
DRM_LOG_MODE(fmt, args...)
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A driver will use the _DRM_DRIVER map flag to indicate that it wants
to be responsible for removing the map itself, bypassing the DRM's
automagic cleanup code.
Since the multi-master changes this has been broken, resulting in some
drivers having their registers unmapped before it's finished with them.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Calls to kcalloc() for a single element can be simplified to calls to
kzalloc().
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the DRM-driven DPMS code, encoders are considered idle unless a
connector is hooked to them, so mode setting is skipped. This makes load
detection fail as none of the hardware is enabled.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
To differentiate between encountering an out-of-memory error with running
out of space in the aperture, use ENOSPC for the later.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Ensure that the drm_vblank_pre_modeset() is always balanced by
drm_vblank_post_modeset() within intel_crtc_mode_set().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
The batch buffer may be shared with another read buffer, so we should not
ignore any previously set domains, but just or in the command domain (and
check that the buffer is not writable).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
By sending a broken execbuffer (its length was not suitably aligned) I
triggered an operation upon a freed object. The invalid alignment was
discovered after updating the write_domain on the object but before the
object was placed on the active queue. So during the unwind process
following the error, the now freed object attempts to flush its
non-existent, but outstanding, GPU writes causing this use-after-free.
[drm:i915_dispatch_gem_execbuffer] *ERROR* alignment
[drm:i915_gem_execbuffer] *ERROR* dispatch failed -22
WARNING: at lib/kref.c:43 warn_slowpath_null+0x10/0x15()
Modules linked in:
Pid: 4552, comm: lt-csi-drm Not tainted 2.6.30-rc6 #423
Call Trace:
[<c0119ef3>] warn_slowpath_fmt+0x57/0x6d
[<c014de24>] ? get_pageblock_migratetype+0x18/0x1e
[<c014e8fd>] ? free_hot_page+0xa/0xc
[<c014e915>] ? __free_pages+0x16/0x1f
[<c0153ebf>] ? shmem_truncate_range+0x63e/0x656
[<c015fb2f>] ? slob_page_alloc+0x146/0x1c8
[<c0119f19>] warn_slowpath_null+0x10/0x15
[<c01f55f2>] kref_get+0x1b/0x21
[<c02605db>] i915_gem_object_move_to_active+0x1f/0x56
[<c0261302>] i915_add_request+0x156/0x19a
[<c026136e>] i915_gem_object_flush_gpu_write_domain+0x28/0x3f
[<c0261eca>] i915_gem_object_unbind+0x4a/0x124
[<c0261fd7>] i915_gem_free_object+0x33/0x9b
[<c0250d6b>] drm_gem_object_free+0x28/0x4a
[<c0250d43>] ? drm_gem_object_free+0x0/0x4a
[<c01f55ce>] kref_put+0x38/0x41
[<c0250cbf>] drm_gem_object_unreference+0x11/0x13
[<c0250d06>] drm_gem_object_handle_unreference+0x1e/0x21
[<c0250d13>] drm_gem_object_release_handle+0xa/0xe
[<c01f3e6b>] idr_for_each+0x5f/0x98
[<c0250d09>] ? drm_gem_object_release_handle+0x0/0xe
[<c0250daf>] drm_gem_release+0x22/0x34
[<c025046f>] drm_release+0x1e8/0x3c4
[<c0162d25>] __fput+0xaf/0x146
[<c0162dce>] fput+0x12/0x14
[<c01605ef>] filp_close+0x48/0x52
[<c011b182>] put_files_struct+0x57/0x9b
[<c011b1e4>] exit_files+0x1e/0x20
[<c011c6b6>] do_exit+0x16d/0x511
[<c03704ab>] ? __schedule+0x3d4/0x3e5
[<c0103f0d>] ? handle_irq+0xd/0x69
[<c011caa7>] do_group_exit+0x4d/0x73
[<c011cae0>] sys_exit_group+0x13/0x17
[<c010268c>] sysenter_do_call+0x12/0x2b
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Update interrupt handling methods for IGDNG with new registers
for display and graphics interrupt functions. As we won't use
irq-based vblank sync in dri2, so display interrupt on new chip
will be used for hotplug only in future.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Using the new PNP resource checking code, this patch allows the i915
driver to allocate MCHBAR space if needed and use the BAR to determine
current memory settings.
[apw@canonical.com: moved to the new generic PNP resource interface]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
failure to update-index after git-am --reject to hand-apply
Signed-off-by: Eric Anholt <eric@anholt.net>
This reverts commit 6c51d1cfa0, which
apparently causes DRI initialization failures on Radeons.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Requested-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sysrq functions are executed in hardirq context, so we shouldn't be
calling sleeping functions from them, like mutex_locks or memory
allocations.
Fix up the i915 sysrq handler to avoid this.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
All G4x and newer chips use the new style frame count register, with a
full 32 bit frame count. Update the code to reflect this.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fix a FIXME in the intel LVDS bring-up code, adding the appropriate
blacklist entry for the AOpen Mini PC, courtesy of a dmidecode
dump from Florian Demmer.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
CC: Florian Demmer <florian@demmer.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The general definition block contains the child device tables, which include
the SDVO device info. For example: device slave address, device dvo port,
device type.
We will get the info of SDVO device by parsing the general definition blocks.
Only when a valid slave address is found, it is regarded as the SDVO device.
And the info of DVO port and slave address is recorded.
http://bugs.freedesktop.org/show_bug.cgi?id=20429
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds the register definitions for the display port enable register
along with those for the GMCH and Link M/N ratios required to drive display
port outputs.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We can safely assume that cursor addresses will not extend beyond the
addressable screen dimensions; setting the additional bits is harmless in
any case.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We detect TV connect status by setting DAC voltage level override
values as 0.7 voltage for DAC_A/B/C. The corresponding 2-bits shold be 0x2,
In order correctly to set last bit as 0, at first we must clean it.
It fixed freedesktop.org bug #21204
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds kernel mode setting on IGDNG with VGA output support.
Note that suspend/resume doesn't work yet.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Disable OpRegion support for now until verified on new chipsets.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
[anholt: dropped drm_pciids.h hunk to avoid loading an incomplete driver]
Signed-off-by: Eric Anholt <eric@anholt.net>
keithp didn't like the original 20ms plan because a cooperative client could
be starved by an uncooperative client. There may even have been problems
with cooperative clients versus cooperative clients. So keithp changed
throttle to just wait for the second to last seqno emitted by that client.
It worked well, until we started getting more round-trips to the server
due to DRI2 -- the server throttles in BlockHandler, and so if you did more
than one round trip after finishing your frame, you'd end up unintentionally
syncing to the swap.
Fix this by keeping track of the client's requests, so the client can wait
when it has an outstanding request over 20ms old. This should have
non-starving behavior, good behavior in the presence of restarts, and less
waiting. Improves high-settings openarena performance on my GM45 by 50%.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This may fix cursor corruption in X on resume, which would persist until
the cursor was hidden and then shown again.
V2: Also include the cursor control regs.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This could be triggered by a gtt mapping fault on 965 that decides to
remove the fence from another object that happens to be active currently.
Since the other object doesn't rely on the fence reg for its execution, we
don't wait for it to finish. We'll soon be not waiting on 915 most of the
time as well, so just drop the BUG_ON.
Signed-off-by: Eric Anholt <eric@anholt.net>
Some EDIDs lie and report tiny modes that aren't possible. Ignore
these modes.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A driver will use the _DRM_DRIVER map flag to indicate that it wants
to be responsible for removing the map itself, bypassing the DRM's
automagic cleanup code.
Since the multi-master changes this has been broken, resulting in some
drivers having their registers unmapped before it's finished with them.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
intel_no_lvds[] does not require __initdata as it is used only by
void intel_lvds_init(struct drm_device *dev).
Signed-off-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Making the drm_crtc.c code recognize the DPMS property and invoke the
connector->dpms function doesn't remove any capability from the driver while
reducing code duplication.
That just highlighted the problem with the existing DPMS functions which
could turn off the connector, but failed to turn off any relevant crtcs. The
new drm_helper_connector_dpms function manages all of that, using the
drm_helper-specific crtc and encoder dpms functions, automatically computing
the appropriate DPMS level for each object in the system.
This fixes the current troubles in the i915 driver which left PLLs, pipes
and planes running while in DPMS_OFF mode or even while they were unused.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Without initializing the sysfs attributes for the edid file,
it was created with mode 0, making it difficult for applications to use.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The contents of various simple text files in sysfs should end with
a newline to make them easier to read from the console.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
fd.o bz#21849
We were aligning to +16 dwords, instead of to the next 16dword
boundary in the ring. Fix the calculation to go to the next 16dword
boundary when space checking.
Signed-off-by: Dave Airlie <airlied@redhat.com>
allocating devname in the i915 driver was a hack originally and I
forgot to figure out how to do this properly back then.
So this is the cleaner version that just picks devname or driver name
in the irq code.
It removes the devname allocs from the i915 driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/built-in.o: In function `intel_opregion_init':
(.text+0x9d540): undefined reference to `acpi_video_register'
v2: move under DRM_I915 from DRM_I915_KMS
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
When a GEM object is evicted from the GTT we set it to the CPU domain,
as it might get swapped in and out or ever mmapped regularly. If the
object is mmapped through the GTT it can still get evicted in this way
by other objects requiring GTT space. When the GTT mapping is touched
again we fault it back into the GTT, but fail to set it back to the
GTT domain. This means we fail to flush any cached CPU writes to the
pages backing the object which will then happen "eventually", typically
after we write to the page through the uncached GTT mapping.
[anholt: Note that userland does do a set_domain(GTT, GTT) when starting
to access the GTT mapping. That covers getting the existing mapping of the
object synchronized if it's bound to the GTT. But set_domain(GTT, GTT)
doesn't do anything if the object is currently unbound. This fix covers the
transition to being bound for GTT mapping.]
Fixes glyph and other pixmap corruption during swapping. fd.o bug #21790
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
On the 865, but not the 855, the clflush we do appears to not actually make
it out to the hardware all the time. An easy way to safely reproduce was
X -retro, which would show that some of the blits involved in drawing the
lovely root weave didn't make it out to the hardware. Those blits are 32
bytes each, and 1-2 would be missing at various points around the screen.
Other experimentation (doing more clflush, doing more AGP chipset flush,
poking at some more device registers to maybe trigger more flushing) didn't
help. krh came up with the wbinvd as a way to successfully get all those
blits to appear.
Signed-off-by: Eric Anholt <eric@anholt.net>
The pitch field is an exponent on pre-965, so we were rejecting buffers
on 8xx that we shouldn't have. 915 got lucky in that the largest legal
value happened to match (8KB / 512 = 0x10), but 8xx has a smaller tile width.
Additionally, we programmed that bad value into the register on 8xx, so the
only pitch that would work correctly was 4096 (512-1023 pixels), while others
would probably give bad rendering or hangs.
Signed-off-by: Eric Anholt <eric@anholt.net>
fd.o bug #20473.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Add support for VGA load detection (pre-945).
drm/i915: Use an I2C algo to do the flip to SDVO DDC bus.
drm/i915: Determine type before initialising connector
drm/i915: Return SDVO LVDS VBT mode if no EDID modes are detected.
drm/i915: Fetch SDVO LVDS mode lines from VBT, then reserve them
i915: support 8xx desktop cursors
drm/i915: allocate large pointer arrays with vmalloc
Two approaches for VGA detections: hot plug detection for 945G onwards
and load pipe detection for Pre-945G. Load pipe detection will get one free
pipe, set border color as red and blue, then check CRT status by
swf register. This is a sync-up with the 2D driver.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Previously, we would set the control bus switch before calls were made
to request EDID information over DDC. But recently the DDC code started
doing multiple I2C transfers to get the EDID extensions as well. This
tripped up SDVO, because the control bus switch is only in effect until
the next STOP after a START. By doing our own algo, we can wrap each i2c
transaction on the DDC I2C bus with the control bus switch it requires.
freedesktop.org bug #21042
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: Hand application for conflict, fixed error path]
Signed-off-by: Eric Anholt <eric@anholt.net>
drm_connector_init sets both the connector type and the connector type_id
on the newly initialised connector. As the connector type_id is coupled to
the connector type, the connector type cannot simply be modified on an
initialised connector.
This patch changes the order of operations on intel_sdvo_init so that the
type is determined before the connector is intialised.
This fixes a bug whereby the name card0-VGA-1 would be allocted to both a
CRT and an SDVO connector since the SDVO connector would be initialised
with type 'unknown' and hence have its type_id assigned from the wrong pool.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Eric Anholt <eric@anholt.net>
Some new SDVO LVDS hardware doesn't have DDC available, and this should
fix the display on it.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For some reason we never added 8xx desktop cursor support to the
kernel. This patch fixes that.
[krh: Also set the size on pre-i915 hw.]
Tested-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes a regression from commit 9d5b3ffc42
('drm: fixup some of the ioctl function exit paths'): The vblank ioctl
needs to update the userspace parameters when interrupted by a signal,
which was prevented by the return code check. This could cause the X
server to hang in drmWaitVBlank().
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently, userspace can fail to obtain the SAREA mapping (among other
reasons) if it passes SAREA_MAX to drmAddMap without aligning it to the
page size. This breaks for example on PowerPC with 64K pages and radeon
despite the kernel radeon actually doing the right rouding in the first
place.
The way SAREA_MAX is defined with a bunch of ifdef's and duplicated
between libdrm and the X server is gross, ultimately it should be
retrieved by userspace from the kernel, but in the meantime, we have
plenty of existing userspace built with bad values that need to work.
This patch works around broken userspace by rounding the requested size
in drm_addmap_core() of any SHM map to the page size. Since the backing
memory for SHM maps is also allocated within addmap_core, there is no
danger of adjacent memory being exposed due to the increased map size.
The only side effect is that drivers that previously tried to create or
access SHM maps using a size < PAGE_SIZE and failed (getting -EINVAL),
will now succeed at the cost of a little bit more memory used if that
happens to be when the map is created.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For awhile now, many of the GEM code paths have allocated page or
object arrays with the slab allocator. This is nice and fast, but
won't work well if memory is fragmented, since the slab allocator works
with physically contiguous memory (i.e. order > 2 allocations are
likely to fail fairly early after booting and doing some work).
This patch works around the issue by falling back to vmalloc for
>PAGE_SIZE allocations. This is ugly, but much less work than chaining
a bunch of pages together by hand (suprisingly there's not a bunch of
generic kernel helpers for this yet afaik). vmalloc space is somewhat
precious on 32 bit kernels, but our allocations shouldn't be big enough
to cause problems, though they're routinely more than a page.
Note that this patch doesn't address the unchecked
alloc-based-on-ioctl-args in GEM; that needs to be fixed in a separate
patch.
Also, I've deliberately ignored the DRM's "area" junk. I don't think
anyone actually uses it anymore and I'm hoping it gets ripped out soon.
[Updated: removed size arg to new free function. We could unify the
free functions as well once the DRM mem tracking is ripped out.]
fd.o bug #20152 (part 1/3)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
drivers/built-in.o: In function `intel_opregion_init':
(.text+0x9d540): undefined reference to `acpi_video_register'
http://bugzilla.kernel.org/show_bug.cgi?id=13165
Signed-off-by: Len Brown <len.brown@intel.com>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Add new GET_PIPE_FROM_CRTC_ID ioctl.
drm/i915: Set HDMI hot plug interrupt enable for only the output in question.
drm/i915: Include 965GME pci ID in IS_I965GM(dev) to match UMS.
drm/i915: Use the GM45 VGA hotplug workaround on G45 as well.
drm/i915: ignore LVDS on intel graphics systems that lie about having it
drm/i915: sanity check IER at wait_request time
drm/i915: workaround IGD i2c bus issue in kernel side (v2)
drm/i915: Don't allow binding objects into the last page of the aperture.
drm/i915: save/restore fence registers across suspend/resume
drm/i915: x86 always has writeq. Add I915_READ64 for symmetry.
Commit 79e539453b introduced a
regression where you cannot use sysrq 'g' to enter kgdb. The solution
is to move the intel fb sysrq over to V for video instead of G for
graphics. The SMP VOYAGER code to register for the sysrq-v is not
anywhere to be found in the mainline kernel, so the comments in the
code were cleaned up as well.
This patch also cleans up the sysrq definitions for kgdb to make it
generic for the kernel debugger, such that the sysrq 'g' can be used
in the future to enter a gdbstub or another kernel debugger.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This allows userlevel code to discover the pipe number corresponding
to a given CRTC ID. This is necessary for doing pipe-specific
operations such as waiting for vblank on a given CRTC. Failure to use
the right pipe mapping can result in GPU hangs, or at least failure
to actually sync to vblank.
Signed-off-by: Carl Worth <cworth@cworth.org>
[anholt: Style touchups from review]
Signed-off-by: Eric Anholt <eric@anholt.net>
We detect HDMI output connection status by writing to HOT Plug Interrupt
Detect Enable bit in PORT_HOTPLUG_EN. The behavior will generate a specified
interrupt, which is caught by audio driver, but during one detection driver
set all Detect Enable bits of HDMIB, HDMIC HDMID, and generate wrong
interrupt signals for current output, according to the signals audio driver
misunderstand device status. The patch intends to handle corresponding
output precisely.
It fixed freedesktop.org bug #21371
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
It fixed bug #21659
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: hand-applied because git-am is too picky]
Signed-off-by: Eric Anholt <eric@anholt.net>
Although spec say CRT_HOTPLUG_ACTIVATION_PERIOD_64 is only useful for
mobile platform, it is also required to detect vga on G4x desktops correctly.
Tested on G45/G43/Q45 platforms with no regressions.
It fixed freedesktop.org bug #21120 and part of bug #21210
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
There are a number of small form factor desktop systems with Intel mobile
graphics chips that lie and say they have an LVDS. With kernel mode-setting,
this becomes a problem, and makes native resolution boot go haywire -- for
example, my Dell Studio Hybrid, hooked to a 1920x1080 display claims to
have a 1024x768 LVDS, and the resulting graphical boot on the 1920x1080
display uses only the top left 1024x768, and auto-configured X will end
up only 1024x768 as well. With this change, graphical boot and X
both do 1920x1080 as expected.
Note that we're simply embracing and extending the early bail-out code
in place for the Mac Mini here. The xorg intel driver uses pci subsystem
device and vendor id for matching, while we're using dmi lookups here.
The MSI addition is courtesy of and tested by Bill Nottingham.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Bill Nottingham <notting@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We might sleep here anyway so I hope an extra uncached read is ok to
add.
In #20896 we found that vbetool clobbers the IER. In KMS mode this is
particularly bad since we don't set the interrupt regs late (in
EnterVT), so we'd fail to get *any* interrupts at all after X started
(since some distros have scripts that call vbetool at X startup
apparently).
So this patch checks IER at wait_request time, and re-enables
interrupts if it's been clobbered. In a proper config this check
should never be triggered.
This is really a distro issue, but having a sanity check is nice, as
long as it doesn't have a real performance hit.
Tested-by: Mateusz Kaduk <mateusz.kaduk@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Moved the check inside of the sleeping case to avoid perf cost]
Signed-off-by: Eric Anholt <eric@anholt.net>
In IGD, DPCUNIT_CLOCK_GATE_DISABLE bit should be set, otherwise i2c
access will be wrong.
v2: Disable CLOCK_GATE_DISABLE bit after bit bashing as suggested by Eric.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This should avoid a class of bugs where the hardware prefetches past the
end of the object, and walks into unallocated memory when the object is
bound to the last page of the aperture.
fd.o bug #21488
Signed-off-by: Eric Anholt <eric@anholt.net>
People keep getting bitten by this, so just auto-select it by default,
assuming most configurations will actually want a console.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/r128: fix r128 ioremaps to use ioremap_wc.
drm: cleanup properly in drm_get_dev() failure paths
drm: clean the map list before destroying the hash table
drm: remove unreachable code in drm_sysfs.c
drm: add control node checks missing from kms merge
drm/kms: don't try to shortcut drm mode set function
drm/radeon: bump minor version for occlusion queries support
This makes software fallbacks not do tiling wrong on i965 and later after
resume. It also should fix 945 performance reduction after resume which
would have disabled tiling without causing any visible effect.
Signed-off-by: Keith Packard <keithp@keithp.com>
[anholt: Fixed up the 915 case to not save/restore the new regs]
Signed-off-by: Eric Anholt <eric@anholt.net>
i386 has inline code for writeq and readq, so just use those instead of ugly
macros which evaluate arguments multiple times.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix up error path leak in i915_cmdbuffer
drm/i915: fix unpaired i915 device mutex on entervt failure.
drm/i915: add support for G41 chipset
drm/i915: Enable ASLE if present
drm/i915: Unregister ACPI video driver when exiting
drm/i915: Register ACPI video even when not modesetting
drm/i915: fix transition to I915_TILING_NONE
drm/i915: Don't let an oops get triggered from irq_emit without dma init.
drm/i915: allow tiled front buffers on 965+
The hash tables contains some of the mapping
so its really nice to have it for the deletion phase.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This line that checks the DRM_CONTROL_ALLOW flag was missed from the KMS
merge. Re-add the check on the IOCTL, as this is currently the only use of
this flag.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We have a drm_set_config which takes a crtc/encoder/mode setup,
and checks it to see if it can shortcut and just do a base setup,
or whether a complete mode setting is required.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We already added support, just need to let userspace
know when it can use them.
Signed-off-by: Maciej Cencora <m.cencora@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The ACPI video driver defers registration to the i915 driver if the
system supports opregion-mediated backlight control. This registration
was only being performed in the KMS case. Ensure it's done even if we
don't have modesetting enabled.
http://bugzilla.kernel.org/show_bug.cgi?id=13048
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 201361a5 introduces a leak when unwinding on error. Reorder
unwind, and eliminate leak.
Cc: Eric Anholt <eric@anholt.net>
Cc: Keith Packard <keithp@keithp.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
[anholt: fixed uninit variable use introduced in original patch]
Signed-off-by: Eric Anholt <eric@anholt.net>
This had been delayed for some time due to failure to work on the one piece
of G41 hardware we had, and lack of success reports from anybody else.
Current hardware appears to be OK.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
[anholt: hand-applied due to conflicts with IGD patches]
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
agp: zero pages before sending to userspace
drm: check for minor master before allowing drop master.
drm: set/clear is_master when master changed
drm: clean dirty memory after device release
drm: count reaches -1
When fast user switching a lot eventually we get to the point,
where we were checking for the wrong thing in this function.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The variable is_master is being used to track the drm_file that is currently
master, so its value needs to be updated accordingly when the master is
changed.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In current code we register/unregister connector object by
drm_sysfs_connector_add/remove function.
However under some cases, we need to dynamically register or unregister device
multiple times, so we have to go through register -> unregister ->register
routine.
Because after device_unregister function our memory is dirty, we need to do
clean operation in order to re-register the device, otherwise the system
will crash. The patch intends to clean device after device release.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With a postfix decrement in the test count will reach -1 rather than 0,
subsequent tests fail.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The changes to opregion initialisation order meant that the ASLE setup
code might not be run at the correct time. Ensure that the interrupts are
set up.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The i915 DRM triggers registration of the ACPI video driver on load. It
should unregister it at unload in order to avoid generating backtraces on
being reloaded.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The ACPI video driver defers registration to the i915 driver if the
system supports opregion-mediated backlight control. This registration
was only being performed in the KMS case. Ensure it's done even if we
don't have modesetting enabled.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Transitions to TILING_NONE skipped the call to unbind the object, which left
the fence register set and caused future CPU access through the GTT to
access the object in tiled mode.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch corrects a pretty big oversight in the KMS code for 965+
chips. The current code is missing tiled surface register programming,
so userland can allocate a tiled surface and use it for mode setting,
resulting in corruption. This patch fixes that, allowing for tiled
front buffers on 965+.
Cc: stable@kernel.org
Tested-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix scheduling while holding the new active list spinlock
drm/i915: Allow tiling of objects with bit 17 swizzling by the CPU.
drm/i915: Correctly set the write flag for get_user_pages in pread.
drm/i915: Fix use of uninitialized var in 40a5f0de
drm/i915: indicate framebuffer restore key in SysRq help message
drm/i915: sync hdmi detection by hdmi identifier with 2D
drm/i915: Fix a mismerge of the IGD patch (new .find_pll hooks missed)
drm/i915: Implement batch and ring buffer dumping
regression caused by commit 5e118f4139feafe97e913df67b1f7c1e5083e535:
i915_gem_object_move_to_inactive() should be called in task context,
as it calls fput();
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
[anholt: Add more detail to the comment about the lock break that's added]
Signed-off-by: Eric Anholt <eric@anholt.net>
Save the bit 17 state of the pages when freeing the page list, and
reswizzle them if necessary when rebinding the pages (in case they were
swapped out). Since we have userland with expectations that the swizzle
enums let it pread and pwrite contents accurately, we can't expose a new
swizzle enum for bit 17 (which it would have to GTT map to handle), so we
handle it down in pread and pwrite by swizzling the copy when bit 17 of the
page address is set.
Signed-off-by: Eric Anholt <eric@anholt.net>
Otherwise, the results of our read didn't show up when we were faulting in
the page being read into (as happened with a testcase reading into a big
stack area). Likely accounts for some conformance test failures.
Signed-off-by: Eric Anholt <eric@anholt.net>
i915_gem_put_relocs_to_user returned an uninitialized value which
got returned to userspace. This caused libdrm in my setup to never
get out of a do{}while() loop retrying i915_gem_execbuffer.
result was hanging X, overheating of cpu and 2-3gb of logfile-spam.
This patch adresses the issue by
1. initializing vars in this file where necessary
2. correcting wrongly interpreted return values of copy_[from/to]_user
Signed-off-by: Florian Mickler <florian@mickler.org>
[anholt: cleanups of unnecessary changes, consistency in APIs]
Signed-off-by: Eric Anholt <eric@anholt.net>
At the same time, bring the action message closer to the usual format.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Currently we detect HDMI monitor by hardware detection, but if an HDMI-DVI
adapter is used to connect a DVI monitor, hardware detection will incorrectly
take monitor as HDMI. HDMI spec says any device containing IEEE registration
identifier will be treated as HDMI device. The patch intends to detect HDMI
monitor by drm_detect_hdmi_monitor function which follows that rule.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We create a debugfs node (i915_ringbuffer_data) to expose a hex dump
of the ring buffer itself. We also expose another debugfs node
(i915_ringbuffer_info) with information on the state (i.e. head, tail
addresses) of the ringbuffer.
For batchbuffer dumping, we look at the device's active_list, dumping
each object which has I915_GEM_DOMAIN_COMMAND in its read
domains. This is all exposed through the dri/i915_batchbuffers debugfs
file with a header for each object (giving the objects gtt_offset so
that it can be matched against the offset given in the
BATCH_BUFFER_START command.
Signed-off-by: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Copy/paste error. The RV670 microcode should work ok, so it's
not a show stopper.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
EDIDs should be backward compatible, so don't bail if we see a version
of 3 (which is out there now) and print a message if we see something
newer, but allow it to be parsed.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check whether the INTERLACE/DBLSCAN is supported by output device. If
not, the mode containing the flag of INTERLACE/DBLSCAN will be marked
as unsupported.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Should be,
edid_vendor[2] = (edid->mfg_id[1] & 0x1f) + '@';
Since vendor ID has only two bytes only, I am somewhat surprised why gcc
doesn't complain this.
Reported-by: Guo, Chaohong <chaohong.guo@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise, the PAGE_CACHE_WC would end up getting us a UC-only mapping, and
the write performance of GTT maps dropped 10x.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: cleaned up unused var]
Signed-off-by: Eric Anholt <eric@anholt.net>
This is a baby-step in the direction of having finer-grained
locking than the struct_mutex. Specifically, this will enable
new debugging code to read the active list for printing out
GPU state when the GPU is wedged, (while the struct_mutex is
held, of course).
Signed-off-by: Carl Worth <cworth@cworth.org>
[anholt: indentation fix]
Signed-off-by: Eric Anholt <eric@anholt.net>
This brings SDVO TV support from 2D driver, including origin
fix f1ca56e17d0 and later fix 2fcf4fcccfe. Also fix wrong modeline
definitions for SDVO TV.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fix compile error of intel_sdvo_debug_response(),
and explicit use KERN_DEBUG for printk.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Only set TV DAC in property change seems doesn't work, we have to
setup whole crtc pipe which assigned to TV alone.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
[anholt: Note that this should also fix the oops at startup with new 2D]
Signed-off-by: Eric Anholt <eric@anholt.net>
If there's no real property change, don't need to set TV mode again.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
[anholt: checkpatch.pl fix]
Signed-off-by: Eric Anholt <eric@anholt.net>
udelay() of 20 milliseconds really ought to just use mdelay(), that avoids
the various wrap scenarios and also is more readable
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add VGA port hotplug detection to the i915 driver. When KMS is enabled,
plugging in or removing a VGA cable from the VGA connector will
generate a uevent, which indicates to userspace that it should re-probe
outputs on this device (to determine modes, etc.).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: dropped extra PORT_HOTPLUG_STAT clear with ack from jbarnes]
Signed-off-by: Eric Anholt <eric@anholt.net>
IGD device only has last 1 page used by GTT. This should match the AGP gart
code.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
drm_get_edid will store edid into raw_edid, so when freeing edid memory,
at the same time clean raw_edid pointer.
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: Note that raw_edid is not currently used anywhere]
Signed-off-by: Eric Anholt <eric@anholt.net>
Indicates something is wrong with the mapping; and apparently triggers
in current kernels.
Signed-off-by: Jesse Barnes <jbarnes@virtuosugeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This fixes all the tiling problems with the 2d ddx. glxgears still doesn't work.
Changes:
- fix a copy&paste error in i8xx fence reg setup. It resulted in an at most a
512KB offset of the fence reg window, so was only visible sometimes.
- add tests for stride and object size constrains (also for i915 and 1965 class
hw). Userspace seems to have an of-by-one bug there, which changes the fence
size by at most 512KB due to an overflow.
- because i8xx hw is quite old (and therefore not as well-tested) I left 2 debug
WARN_ONs in the i8xx fence reg setup code to hopefully catch any further
overflows in the bit-fields. Lastly there's one small change to make the
alignment checks more consistent.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=20289
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Sometime we need to communicate with HDMI monitor by sending audio or video
info frame, so we have to know monitor type. However if user utilize HDMI-DVI adapter to connect DVI monitor, hardware detection will incorrectly show the monitor is HDMI. HDMI spec tell us that any device containing IEEE registration Identifier will be treated as HDMI device. The patch intends to detect HDMI monitor by this rule.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_open_helper() from drm_fops.c had a missing mutex_unlock in a error
path.
This was caught by smatch (http://repo.or.cz/w/smatch.git/). Compile
tested.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Usually drm read basic EDID, that is enough for us, but since igital display
were introduced i.e. HDMI monitor, sometime we need to interact with monitor by
EDID extension information,
EDID extensions include audio/video data block, speaker allocation and vendor specific data blocks.
This patch intends to read EDID extensions from digital monitor for users.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The kmalloc was taking up about 1.5% of the CPU on an ioctl-heavy workload
(x11perf -aa10text on 965). Initial results look like they have a
corresponding improvement in performance for aa10text, but more numbers might
not hurt.
Thanks to ajax for pointing out this performance regression I'd introduced
back in 2007.
[airlied: well I introduced it sneakily inside Eric's patch]
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This produced a warning on my build, not sure why super-warning-man didn't
notice this one, its much worse than the %z one.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
arch/sparc/kernel/time_64.c
drivers/gpu/drm/drm_proc.c
Manual merge to resolve build warning due to phys_addr_t type change
on x86:
drivers/gpu/drm/drm_info.c
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Intel graphics hardware that implements the ACPI IGD OpRegion spec
requires that the list of display devices be populated before any ACPI
video methods are called. Detect when this is the case and defer
registration until the opregion code calls it. Fixes crashes on HP
laptops.
http://bugzilla.kernel.org/show_bug.cgi?id=11259
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Len Brown <len.brown@intel.com>
For the fifteen bazillionth time.
See also commits f06da264cf and
aeb565dfc3 ("i915: Fix more size_t format
string warnings" and "Fix annoying DRM_ERROR() string warning").
Grr-target: Eric Anholt <eric@anholt.net>
Grr-target: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update bdb_lvds_options structure according to its defination in
2D driver. Then we can parse and set 'lvds_dither' bit correctly
on non-965 chips.
Signed-off-by: Li Peng <peng.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
I've hit the occasional oops inside i915_wait_ring() with an indication of
a NULL derefence of dev->primary->master. Adding a NULL check is
consistent with the other potential users of dev->primary->master.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Check that the encoder has a real enabled crtc for TV detect, and fix
missing TV type setting after detect.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fix TV control save register for untouched bits, and color
knobs different definition for 945 and 965 chips.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The get_modes hook must return the number of modes added. This also fixes
TV mode's clock calculation int overflow issue, and use 0.01 precision for
mode refresh validation.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This covers:
Use long crt hotplug activation time on GM45.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This covers:
Limit CRT DAC speed better.
and also clears the border color in case it's set to some garbage, which would
fix ugly outlines in the blank regions of the CRT.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
[anholt: replaced *drm_dev with *dev]
Signed-off-by: Eric Anholt <eric@anholt.net>
This covers at least:
TV: subcarrier fix for NTSC and PAL
TV: fix timing parameters for PAL, 480p, 1080i
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
agp_chipset_flush() is for flushing the intel GMCH write cache via the
IFP, these two uses are for when we're getting the object into the cpu
READ domain, and thus should not be needed. This confused me when I was
getting my head around the code.
With thanks to airlied for helping me check my mental picture of how the
flushes and clflushes are supposed to be used.
Signed-off-by: Owain G. Ainsworth <oga@openbsd.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This was inspired by a patch by Chris Wilson, though none of it applied in any
way due to the debugfs work and I decided to change the formatting of the
new information anyway.
Signed-off-by: Eric Anholt <eric@anholt.net>
Here we eliminate a few functions in favor of using a single function
to dump from all of the object lists.
Signed-Off-By: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The old mechanism to formatting proc files is extremely ugly. The
seq_file API was designed specifically for cases like this and greatly
simplifies the process.
Also, most of the files in /proc really don't belong there. This patch
introduces the infrastructure for putting these into debugfs and exposes
all of the proc files in debugfs as well.
Signed-off-by: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This introduces allocation in the batch submission path that wasn't there
previously, but these are compatibility paths so we care about simplicity
more than performance.
kernel.org bug #12419.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Keith Packard <keithp@keithp.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Like the GTT pwrite path fix, this uses an optimistic path and a
fallback to get_user_pages. Note that this means we have to stop using
vfs_write and roll it ourselves.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We've wanted this for a few consumers that touch the pages directly (such as
the following commit), which have been doing the refcounting outside of
get/put pages.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since the pagefault path determines that the lock order we use has to be
mmap_sem -> struct_mutex, we can't allow page faults to occur while the
struct_mutex is held. To fix this in pwrite, we first try optimistically to
see if we can copy from user without faulting. If it fails, fall back to
using get_user_pages to pin the user's memory, and map those pages
atomically when copying it to the GPU.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This fixes incorrect detection of the second SDVO/HDMI output on G4X, and
extra boot time on pre-G4X.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This improves the PLL timings according to the suggestion of the hardware
engineers. This results in some outputs being able to sync that weren't
able to before.
This is part of fixing fd.o bug #17508.
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: cleaned up a couple of redundant comments]
Signed-off-by: Eric Anholt <eric@anholt.net>
The values come from the internal reference spreadsheet on PLL
timing limits for the G4X chipsets.
Part of fixing fd.o bug #17508
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: Cleaned up some whitespace]
Signed-off-by: Eric Anholt <eric@anholt.net>
Later spec investigation has revealed that every 9xx mobile part has
had this register in this format. Also, no non-mobile parts have been shown
to have this register. So make all mobile use the same code, and all
non-mobile use the hack 965 detection.
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'bkl-removal' of git://git.lwn.net/linux-2.6:
Rationalize fasync return values
Move FASYNC bit handling to f_op->fasync()
Use f_lock to protect f_flags
Rename struct file->f_ep_lock
Most fasync implementations do something like:
return fasync_helper(...);
But fasync_helper() will return a positive value at times - a feature used
in at least one place. Thus, a number of other drivers do:
err = fasync_helper(...);
if (err < 0)
return err;
return 0;
In the interests of consistency and more concise code, it makes sense to
map positive return values onto zero where ->fasync() is called.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This fixes 2 bugs:
1. the AGP calculation wasn't consistent with the PCI(E) calc for the
RPTR_ADDR registers. This consolidates the writes and fixes it up.
2. The scratch address was being incorrectly calculated, this breaks
it out into a lot more linear steps.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix this sparse warning:
drivers/gpu/drm/radeon/r600_cp.c:1811:52: warning: Using plain integer as NULL pointer
drivers/gpu/drm/radeon/radeon_cp.c:1363:52: warning: Using plain integer as NULL pointer
drivers/gpu/drm/radeon/radeon_state.c:1983:61: warning: Using plain integer as NULL pointer
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This realigns the r600 pci mapping calls with the ati pcigart ones,
fixing the direction and using the correct interface.
Suggested by Jerome Glisse.
Signed-off-by: Dave Airlie <airlied@redhat.com>
the checks weren't updated when RS600 support
was added.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
RS600s are an AMD IGP for Intel CPUs, that look like RS690s from
a lot of perspectives but look like r600s from a memory controller
point of view.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds support for 2D/Xv acceleration in the X.org 2D driver,
to the drm. It doesn't yet provide any 3D support hooks.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This uses the same microcode system as the current radeon code.
It should be converted to the new microcode loader I suppose,
though really I need a lot more proof of the worth of me maintaining
firmware blobs externally.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
agp_chipset_flush() is for flushing the intel GMCH write cache via the
IFP, these two uses are for when we're getting the object into the cpu
READ domain, and thus should not be needed. This confused me when I was
getting my head around the code.
With thanks to airlied for helping me check my mental picture of how the
flushes and clflushes are supposed to be used.
Signed-off-by: Owain G. Ainsworth <oga@openbsd.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This was inspired by a patch by Chris Wilson, though none of it applied in any
way due to the debugfs work and I decided to change the formatting of the
new information anyway.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Here we eliminate a few functions in favor of using a single function
to dump from all of the object lists.
Signed-Off-By: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The old mechanism to formatting proc files is extremely ugly. The
seq_file API was designed specifically for cases like this and greatly
simplifies the process.
Also, most of the files in /proc really don't belong there. This patch
introduces the infrastructure for putting these into debugfs and exposes
all of the proc files in debugfs as well.
This contains the i915 hooks rewrite as well, to make bisectability better.
Signed-off-by: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On some radeon GPUs this appears to introduce another level of
stability around interacting with the ring.
Its pretty much what fglrx appears to do.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is usedul when you have multiple cards to figure out which
one is which minor.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only X86 32-bit uses a different alignment for "unsigned long long"
than it's 64-bit counterpart.
Therefore this compat translation is only correct, and only needed,
when either CONFIG_X86 or CONFIG_IA64.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In compat mode, the cmdbuf->buf 64-bit address cookie can
potentially be only 32-bit aligned. Dereferencing this as
64-bit causes expensive unaligned traps on platforms like
sparc64.
Use get_unaligned() to fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Platforms such as sparc64 have D-cache aliasing issues. We
cannot allow virtual mappings in different contexts to be such
that two cache lines can be loaded for the same backing data.
Updates to one cache line won't be seen by accesses to the other
cache line.
Code in sparc64 and other architectures solve this problem by
making sure that all userland mappings of MAP_SHARED objects have
the same virtual address base. They implement this by keying
off of the page offset, and using that to choose a suitably
consistent virtual address for mmap() requests.
Making things even worse, getting this wrong on sparc64 can result
in hangs during DRM lock acquisition. This is because, at least on
UltraSPARC-III, normal loads consult the D-cache but atomics such
as 'cas' (which is what cmpxchg() is implement using) only consult
the L2 cache. So if a D-cache alias is inserted, the load can
see different data than the atomic, and we'll loop forever because
the atomic compare-and-exchange will never complete successfully.
So to make this all work properly, we need to make sure that the
hash address computed by drm_map_handle() preserves the SHMLBA
relevant bits, and that's what this patch does for _DRM_SHM mappings.
As a historical note, many years ago this bug didn't exist because we
used to just use the low 32-bits of the address as the hash and just
hope for the best. This preserved the SHMLBA bits properly. But when
the hashtab code was added to DRM, this was no longer the case.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The variable 'max_pages' is ambiguous. There are two concepts
of "pages" being used in this function.
First, we have ATI GART pages which are always 4096 bytes.
Then, we have system pages which are of size PAGE_SIZE.
Eliminate the confusion by creating max_ati_pages and
max_real_pages. Calculate and use them as appropriate.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This allocates a physical surface for the PCI GART table, this way no
matter what other surface configurations exist the GART table will
always be seen by the hardware properly.
We encode the file pointer of the virtual surface allocate using a
special cookie value, called PCIGART_FILE_PRIV. On the last close, we
release that surface.
Just to be doubly safe, we run the pcigart table setup with the main
surface control register clear.
Based upon ideas from David Airlie and Ben Benjamin Herrenschmidt.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The address needs to be a GART relative address, rather than a PCI
DMA address.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
These are not supposed to be booleans, they are
supposed to be bit masks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The memory behind ring_rptr can either be in ioremapped memory
or a vmalloc() normal kernel memory buffer.
However, the code unconditionally uses DRM_{READ,WRITE}32() (and thus
readl() and writel()) to access it.
Basically, if RADEON_IS_AGP then it's ioremap()'d memory else it's
vmalloc'd memory.
Adjust all of the ring_rptr access code as needed.
While we're here, kill the 'scratch' pointer in drm_radeon_private.
It's only used in the one place where it is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The buffers mapped by the PCI GART can be written to by the device,
not just read.
For example, this happens via the RB_RPTR writeback on Radeon.
So we can't use PCI_DMA_TODEVICE else we'll get protection faults
on IOMMU platforms.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The PCI GART table initialization code treats the GART table mapping
unconditionally as a kernel virtual address.
But it could be in the framebuffer, for example, and thus we're
dealing with a PCI MEM space ioremap() cookie. Treating that as a
virtual address is illegal and will crash some system types (such as
sparc64 where the ioremap() return value is actually a physical I/O
address).
So access the area correctly, using gart_info->gart_table_location as
our guide.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The kernel shouldn't be in the business of telling user space which
driver to load. The kernel defers mapping PCI IDs to module names
to user space and we should do the same for DRI drivers.
And in fact, that's how it does work today. Nothing uses the
dri_library_name attribute, and the attribute is in fact broken.
For intel devices, it falls back to the default behaviour of returning
the kernel module name as the DRI driver name, which doesn't work for
i965 devices. Nobody has ever hit this problem or filed a bug about this.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Under kernel modesetting, we manage the device at all times, regardless
of VT switching and X servers, so the only decent thing to do is to
claim the PCI device. In that case, we call the suspend/resume hooks
directly from the pci driver hooks instead of the current class device detour.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This changes drm_local_map to use a resource_size for its "offset"
member instead of an unsigned long, thus allowing 32-bit machines
with a >32-bit physical address space to be able to store there
their register or framebuffer addresses when those are above 4G,
such as when using a PCI video card on a recent AMCC 440 SoC.
This patch isn't as "trivial" as it sounds: A few functions needed
to have some unsigned long/int changed to resource_size_t and a few
printk's had to be adjusted.
But also, because userspace isn't capable of passing such offsets,
I had to modify drm_find_matching_map() to ignore the offset passed
in for maps of type _DRM_FRAMEBUFFER or _DRM_REGISTERS.
If we ever support multiple _DRM_FRAMEBUFFER or _DRM_REGISTERS maps
for a given device, we might have to change that trick, but I don't
think that happens on any current driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Once upon a time, the DRM made the distinction between the drm_map
data structure exchanged with user space and the drm_local_map used
in the kernel.
For some reasons, while the BSD port still has that "feature", the
linux part abused drm_map for kernel internal usage as the local
map only existed as a typedef of the struct drm_map.
This patch fixes it by declaring struct drm_local_map separately
(though its content is currently identical to the userspace variant),
and changing the kernel code to only use that, except when it's a
user<->kernel interface (ie. ioctl).
This allows subsequent changes to the in-kernel format
I've also replaced the use of drm_local_map_t with struct drm_local_map
in a couple of places. Mostly by accident but they are the same (the
former is a typedef of the later) and I have some remote plans and
half finished patch to completely kill the drm_local_map_t typedef
so I left those bits in.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The DRM uses its own wrappers to obtain resources from PCI devices,
which currently convert the resource_size_t into an unsigned long.
This is broken on 32-bit platforms with >32-bit physical address
space.
This fixes them, along with a few occurences of unsigned long used
to store such a resource in drivers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The last 8 fence registers sit at a different offset, so when we went to set
fence number 8 in the lower offset, we instead set PGETBL_CTL, and the GPU
got all sorts of angry at us.
fd.o bug #20567. Easily reproducible by running glxgears and killing it about
6 times.
Signed-off-by: Eric Anholt <eric@anholt.net>
The i915 also uses the fence registers for GPU access to tiled buffers so
we cannot reallocate one whilst it is on the active list. By performing a
LRU scan of the fenced buffers we also avoid waiting the possibility of
waiting on a pinned, or otherwise unusable, buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
We need to check and report if there are no available fences - or else we
spin endlessly waiting for a buffer to magically unpin itself.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
As we may steal the fence register of an unpinned buffer for another,
every time we repin the buffer we need to recheck whether it needs to be
allocated a fence.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
If we wait upon a request and successfully unbind a buffer occupying a
fence register, then that slot will be freed and cause a NULL derefrence
upon rescanning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
The VGA registers just hit the pipe registers that we already set through
MMIO. This fixes strange colors on resume.
Signed-off-by: Pierre Willenbrock <pierre@pirsoft.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
If userspace passes an object list with the same object appearing more
than once, we end up hitting the BUG_ON() in
i915_gem_object_set_to_gpu_domain() as it gets called a second time
for the same object.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This could be triggered by a client asking to emit an irq when the device
wasn't initialized.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This is done by
1) Wake up lock waiters when we close the master file descriptor.
Not when the master structure is removed, since the latter
requires the waiters themselves to release the refcount on the
master structure -> Deadlock.
2) Send a SIGTERM to all clients waiting for the lock.
Normally these clients will get a SIGPIPE when the X server dies,
but clients may also spin trying to grab the DRM lock, without
getting any sort of notification.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Currently only one waiter is woken up, leaving other waiters
hanging waiting for the DRM lock.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
That return code is for in-kernel use only.
Use EINTR instead.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Impact: standardize IO on cached ops
On modern CPUs it is almost always a bad idea to use non-temporal stores,
as the regression in this commit has shown it:
30d697f: x86: fix performance regression in write() syscall
The kernel simply has no good information about whether using non-temporal
stores is a good idea or not - and trying to add heuristics only increases
complexity and inserts fragility.
The regression on cached write()s took very long to be found - over two
years. So dont take any chances and let the hardware decide how it makes
use of its caches.
The only exception is drivers/gpu/drm/i915/i915_gem.c: there were we are
absolutely sure that another entity (the GPU) will pick up the dirty
data immediately and that the CPU will not touch that data before the
GPU will.
Also, keep the _nocache() primitives to make it easier for people to
experiment with these details. There may be more clear-cut cases where
non-cached copies can be used, outside of filemap.c.
Cc: Salman Qazi <sqazi@google.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: enable DMAR by default
xen: disable interrupts early, as start_kernel expects
gpu/drm, x86, PAT: io_mapping_create_wc and resource_size_t
gpu/drm, x86, PAT: Handle io_mapping_create_wc() errors in a clean way
x86, Voyager: fix compile by lifting the degeneracy of phys_cpu_present_map
x86, doc: fix references to Documentation/x86/i386/boot.txt
io_mapping_create_wc can return NULL on error and io_mapping_free() should be
called on one of the error-cleanup path.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, enable future change
Add a 'total bytes copied' parameter to __copy_from_user_*nocache(),
and update all the callsites.
The parameter is not used yet - architecture code can use it to
more intelligently decide whether the copy should be cached or
non-temporal.
Cc: Salman Qazi <sqazi@google.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
However we still have another issue with ioremap_wc not falling back
properly or somehow doing something else stupid, this probably needs
to be tracked down.
Signed-off-by: Dave Airlie <airlied@redhat.com>
edid->revision == 0 should be valid (at least, so the error message
indicates. :) and wikipedia seems to indicate that EDID 1.0 existed.
We can dump the entire check, since edid->revision is a u8, so
it can't ever be less than 0.
Marko reports in RH bz#476735 that his monitor claims to be
EDID 1.0, and therefore hits the check and is stuck at 800x600 because
of it.
Reported-by: Marko Ristola <marko.ristola@kolumbus.fi>
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Zhao Yakui