The include/asm-powerpc/paca.h file has a prototype for a function that
does not exist any more; its name is setup_boot_paca. This function was
removed in commit 4ba99b97da, so its
prototype should have been removed at that time too.
Signed-off-by: Julio M. Merino Vidal <jmerino@ac.upc.edu>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
This adds POWERPC specific hooks for scaled time accounting.
POWER6 includes a SPURR register. The SPURR is based off the PURR register
but is scaled based on CPU frequency and issue rates. This gives a more
accurate account of the instructions used per task. The PURR and timebase
will be constant relative to the wall clock, irrespective of the CPU
frequency.
This implementation reads the SPURR register in account_system_vtime which
is only call called on context witch and hard and soft irq entry and exit.
The percentage of user and system time is then estimated using the ratio of
these accounted by the PURR. If the SPURR is not present, the PURR read.
An earlier implementation of this patch read the SPURR whenever the PURR
was read, which included the system call entry and exit path.
Unfortunately this showed a performance regression on lmbench runs, so was
re-implemented.
I've included the lmbench results here when run bare metal on POWER6. 1st
column is the unpatch results. 2nd column is the results using the below
patch and the 3rd is the % diff of these results from the base. 4th and
5th columns are the results and % differnce from the base using the older
patch (SPURR read in syscall entry/exit path).
Base Scaled-Acct SPURR-in-syscall
Result Result % diff Result % diff
Simple syscall: 0.3086 0.3086 0.0000 0.3452 11.8600
Simple read: 0.4591 0.4671 1.7425 0.5044 9.86713
Simple write: 0.4364 0.4366 0.0458 0.4731 8.40971
Simple stat: 2.0055 2.0295 1.1967 2.0669 3.06158
Simple fstat: 0.5962 0.5876 -1.442 0.6368 6.80979
Simple open/close: 3.1283 3.1009 -0.875 3.2088 2.57328
Select on 10 fd's: 0.8554 0.8457 -1.133 0.8667 1.32101
Select on 100 fd's: 3.5292 3.6329 2.9383 3.6664 3.88756
Select on 250 fd's: 7.9097 8.1881 3.5197 8.2242 3.97613
Select on 500 fd's: 15.2659 15.836 3.7357 15.873 3.97814
Select on 10 tcp fd's: 0.9576 0.9416 -1.670 0.9752 1.83792
Select on 100 tcp fd's: 7.248 7.2254 -0.311 7.2685 0.28283
Select on 250 tcp fd's: 17.7742 17.707 -0.375 17.749 -0.1406
Select on 500 tcp fd's: 35.4258 35.25 -0.496 35.286 -0.3929
Signal handler installation: 0.6131 0.6075 -0.913 0.647 5.52927
Signal handler overhead: 2.0919 2.1078 0.7600 2.1831 4.35967
Protection fault: 0.7345 0.7478 1.8107 0.8031 9.33968
Pipe latency: 33.006 16.398 -50.31 33.475 1.42368
AF_UNIX sock stream latency: 14.5093 30.910 113.03 30.715 111.692
Process fork+exit: 219.8 222.8 1.3648 229.37 4.35623
Process fork+execve: 876.14 873.28 -0.32 868.66 -0.8533
Process fork+/bin/sh -c: 2830 2876.5 1.6431 2958 4.52296
File /var/tmp/XXX write bw: 1193497 1195536 0.1708 118657 -0.5799
Pagefaults on /var/tmp/XXX: 3.1272 3.2117 2.7020 3.2521 3.99398
Also, kernel compile times show no difference with this patch applied.
[pbadari@us.ibm.com: Avoid unnecessary PURR reading]
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add CONFIG_DEBUG_PREEMPT support to ppc64: it was useful for testing
get_paca() preemption. Cheat a little, just use debug_smp_processor_id()
in the debug version of get_paca(): it contains all the right checks and
reporting, though get_paca() doesn't really use smp_processor_id().
Use local_paca for what might have been called __raw_get_paca().
Silence harmless warnings from io.h and lparcfg.c with local_paca -
it is okay for iseries_lparcfg_data to be referencing shared_proc
with preemption enabled: all cpus should show the same value for
shared_proc.
Why do other architectures need TRACE_IRQFLAGS_SUPPORT for DEBUG_PREEMPT?
I don't know, ppc64 appears to get along fine without it.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The basic issue is to be able to do what hugetlbfs does but with
different page sizes for some other special filesystems; more
specifically, my need is:
- Huge pages
- SPE local store mappings using 64K pages on a 4K base page size
kernel on Cell
- Some special 4K segments in 64K-page kernels for mapping a dodgy
type of powerpc-specific infiniband hardware that requires 4K MMU
mappings for various reasons I won't explain here.
The main issues are:
- To maintain/keep track of the page size per "segment" (as we can
only have one page size per segment on powerpc, which are 256MB
divisions of the address space).
- To make sure special mappings stay within their allotted
"segments" (including MAP_FIXED crap)
- To make sure everybody else doesn't mmap/brk/grow_stack into a
"segment" that is used for a special mapping
Some of the necessary mechanisms to handle that were present in the
hugetlbfs code, but mostly in ways not suitable for anything else.
The patch relies on some changes to the generic get_unmapped_area()
that just got merged. It still hijacks hugetlb callbacks here or
there as the generic code hasn't been entirely cleaned up yet but
that shouldn't be a problem.
So what is a slice ? Well, I re-used the mechanism used formerly by our
hugetlbfs implementation which divides the address space in
"meta-segments" which I called "slices". The division is done using
256MB slices below 4G, and 1T slices above. Thus the address space is
divided currently into 16 "low" slices and 16 "high" slices. (Special
case: high slice 0 is the area between 4G and 1T).
Doing so simplifies significantly the tracking of segments and avoids
having to keep track of all the 256MB segments in the address space.
While I used the "concepts" of hugetlbfs, I mostly re-implemented
everything in a more generic way and "ported" hugetlbfs to it.
Slices can have an associated page size, which is encoded in the mmu
context and used by the SLB miss handler to set the segment sizes. The
hash code currently doesn't care, it has a specific check for hugepages,
though I might add a mechanism to provide per-slice hash mapping
functions in the future.
The slice code provide a pair of "generic" get_unmapped_area() (bottomup
and topdown) functions that should work with any slice size. There is
some trickiness here so I would appreciate people to have a look at the
implementation of these and let me know if I got something wrong.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Save the trap number in the case of getting a bad stack in an exception
handler. It is sometimes useful to know what exception it was that caused
this to happen. Without this, no trap number is reported.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the slb_shadow_ptr field into the first cache line since it is
(like everything there) read-only after boot. It is in fact statically
initialised and thereafter only read.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements a lazy strategy for disabling interrupts. This means
that local_irq_disable() et al. just clear the 'interrupts are
enabled' flag in the paca. If an interrupt comes along, the interrupt
entry code notices that interrupts are supposed to be disabled, and
clears the EE bit in SRR1, clears the 'interrupts are hard-enabled'
flag in the paca, and returns. This means that interrupts only
actually get disabled in the processor when an interrupt comes along.
When interrupts are enabled by local_irq_enable() et al., the code
sets the interrupts-enabled flag in the paca, and then checks whether
interrupts got hard-disabled. If so, it also sets the EE bit in the
MSR to hard-enable the interrupts.
This has the potential to improve performance, and also makes it
easier to make a kernel that can boot on iSeries and on other 64-bit
machines, since this lazy-disable strategy is very similar to the
soft-disable strategy that iSeries already uses.
This version renames paca->proc_enabled to paca->soft_enabled, and
changes a couple of soft-disables in the kexec code to hard-disables,
which should fix the crash that Michael Ellerman saw. This doesn't
yet use a reserved CR field for the soft_enabled and hard_enabled
flags. This applies on top of Stephen Rothwell's patches to make it
possible to build a combined iSeries/other kernel.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the writeX family of functions to have a sync instruction
before the MMIO store rather than after, because the generally expected
behaviour is that the device receiving the MMIO store can be guaranteed
to see the effects of any preceding writes to normal memory.
To preserve ordering between writeX and readX, and to preserve ordering
between preceding stores and the readX, the readX family of functions
have had an sync added before the load.
Although writeX followed by spin_unlock is not officially guaranteed
to keep the writeX inside the spin-locked region unless an mmiowb()
is used, there are currently drivers that depend on the previous
behaviour on powerpc, which was that the mmiowb wasn't actually required.
Therefore we have a per-cpu flag that is set by writeX, cleared by
__raw_spin_lock and mmiowb, and tested by __raw_spin_unlock. If it is
set, __raw_spin_unlock does a sync and clears it.
This changes both 32-bit and 64-bit readX/writeX. 32-bit already has a
sync in __raw_spin_unlock (since lwsync doesn't exist on 32-bit), and thus
doesn't need the per-cpu flag.
Tested on G5 (PPC970) and POWER5.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a shadow buffer for the SLBs and regsiters it with PHYP.
Only the bolted SLB entries (top 3) are shadowed.
The SLB shadow buffer tells the hypervisor what the kernel needs to
have in the SLB for the kernel to be able to function. The hypervisor
can use this information to speed up partition context switches.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (139 commits)
[POWERPC] re-enable OProfile for iSeries, using timer interrupt
[POWERPC] support ibm,extended-*-frequency properties
[POWERPC] Extra sanity check in EEH code
[POWERPC] Dont look for class-code in pci children
[POWERPC] Fix mdelay badness on shared processor partitions
[POWERPC] disable floating point exceptions for init
[POWERPC] Unify ppc syscall tables
[POWERPC] mpic: add support for serial mode interrupts
[POWERPC] pseries: Print PCI slot location code on failure
[POWERPC] spufs: one more fix for 64k pages
[POWERPC] spufs: fail spu_create with invalid flags
[POWERPC] spufs: clear class2 interrupt status before wakeup
[POWERPC] spufs: fix Makefile for "make clean"
[POWERPC] spufs: remove stop_code from struct spu
[POWERPC] spufs: fix spu irq affinity setting
[POWERPC] spufs: further abstract priv1 register access
[POWERPC] spufs: split the Cell BE support into generic and platform dependant parts
[POWERPC] spufs: dont try to access SPE channel 1 count
[POWERPC] spufs: use kzalloc in create_spu
[POWERPC] spufs: fix initial state of wbox file
...
Manually resolved conflicts in:
drivers/net/phy/Makefile
include/asm-powerpc/spu.h
Some POWER5+ machines can do 64k hardware pages for normal memory but
not for cache-inhibited pages. This patch lets us use 64k hardware
pages for most user processes on such machines (assuming the kernel
has been configured with CONFIG_PPC_64K_PAGES=y). User processes
start out using 64k pages and get switched to 4k pages if they use any
non-cacheable mappings.
With this, we use 64k pages for the vmalloc region and 4k pages for
the imalloc region. If anything creates a non-cacheable mapping in
the vmalloc region, the vmalloc region will get switched to 4k pages.
I don't know of any driver other than the DRM that would do this,
though, and these machines don't have AGP.
When a region gets switched from 64k pages to 4k pages, we do not have
to clear out all the 64k HPTEs from the hash table immediately. We
use the _PAGE_COMBO bit in the Linux PTE to indicate whether the page
was hashed in as a 64k page or a set of 4k pages. If hash_page is
trying to insert a 4k page for a Linux PTE and it sees that it has
already been inserted as a 64k page, it first invalidates the 64k HPTE
before inserting the 4k HPTE. The hash invalidation routines also use
the _PAGE_COMBO bit, to determine whether to look for a 64k HPTE or a
set of 4k HPTEs to remove. With those two changes, we can tolerate a
mix of 4k and 64k HPTEs in the hash table, and they will all get
removed when the address space is torn down.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The pgdir field in the paca was a leftover from the dynamic VSIDs
patch, and is not used in the current kernel code. This removes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently have a hack to flip the boot cpu and its secondary thread
to logical cpuid 0 and 1. This means the logical - physical mapping will
differ depending on which cpu is boot cpu. This is most apparent on
kexec, where we might kexec on any cpu and therefore change the mapping
from boot to boot.
The patch below does a first pass early on to work out the logical cpuid
of the boot thread. We then fix up some paca structures to match.
Ive also removed the boot_cpuid_phys variable for ppc64, to be
consistent we use get_hard_smp_processor_id(boot_cpuid) everywhere.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements accurate task and cpu time accounting for 64-bit
powerpc kernels. Instead of accounting a whole jiffy of time to a
task on a timer interrupt because that task happened to be running at
the time, we now account time in units of timebase ticks according to
the actual time spent by the task in user mode and kernel mode. We
also count the time spent processing hardware and software interrupts
accurately. This is conditional on CONFIG_VIRT_CPU_ACCOUNTING. If
that is not set, we do tick-based approximate accounting as before.
To get this accurate information, we read either the PURR (processor
utilization of resources register) on POWER5 machines, or the timebase
on other machines on
* each entry to the kernel from usermode
* each exit to usermode
* transitions between process context, hard irq context and soft irq
context in kernel mode
* context switches.
On POWER5 systems with shared-processor logical partitioning we also
read both the PURR and the timebase at each timer interrupt and
context switch in order to determine how much time has been taken by
the hypervisor to run other partitions ("steal" time). Unfortunately,
since we need values of the PURR on both threads at the same time to
accurately calculate the steal time, and since we can only calculate
steal time on a per-core basis, the apportioning of the steal time
between idle time (time which we ceded to the hypervisor in the idle
loop) and actual stolen time is somewhat approximate at the moment.
This is all based quite heavily on what s390 does, and it uses the
generic interfaces that were added by the s390 developers,
i.e. account_system_time(), account_user_time(), etc.
This patch doesn't add any new interfaces between the kernel and
userspace, and doesn't change the units in which time is reported to
userspace by things such as /proc/stat, /proc/<pid>/stat, getrusage(),
times(), etc. Internally the various task and cpu times are stored in
timebase units, but they are converted to USER_HZ units (1/100th of a
second) when reported to userspace. Some precision is therefore lost
but there should not be any accumulating error, since the internal
accumulation is at full precision.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes all self references and fixes references to files
in the now defunct arch/ppc64 tree. I think this accomplises
everything wanted, though there might be a few references I missed.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present the lppaca - the structure shared with the iSeries
hypervisor and phyp - is contained within the PACA, our own low-level
per-cpu structure. This doesn't have to be so, the patch below
removes it, making a separate array of lppaca structures.
This saves approximately 500*NR_CPUS bytes of image size and kernel
memory, because we don't need aligning gap between the Linux and
hypervisor portions of every PACA. On the other hand it means an
extra level of dereference in many accesses to the lppaca.
The patch also gets rid of several places where we assign the paca
address to a local variable for no particular reason.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current ppc64 per cpu data implementation is quite slow. eg:
lhz 11,18(13) /* smp_processor_id() */
ld 9,.LC63-.LCTOC1(30) /* per_cpu__variable_name */
ld 8,.LC61-.LCTOC1(30) /* __per_cpu_offset */
sldi 11,11,3 /* form index into __per_cpu_offset */
mr 10,9
ldx 9,11,8 /* __per_cpu_offset[smp_processor_id()] */
ldx 0,10,9 /* load per cpu data */
5 loads for something that is supposed to be fast, pretty awful. One
reason for the large number of loads is that we have to synthesize 2
64bit constants (per_cpu__variable_name and __per_cpu_offset).
By putting __per_cpu_offset into the paca we can avoid the 2 loads
associated with it:
ld 11,56(13) /* paca->data_offset */
ld 9,.LC59-.LCTOC1(30) /* per_cpu__variable_name */
ldx 0,9,11 /* load per cpu data
Longer term we can should be able to do even better than 3 loads.
If per_cpu__variable_name wasnt a 64bit constant and paca->data_offset
was in a register we could cut it down to one load. A suggestion from
Rusty is to use gcc's __thread extension here. In order to do this we
would need to free up r13 (the __thread register and where the paca
currently is). So far Ive had a few unsuccessful attempts at doing that :)
The patch also allocates per cpu memory node local on NUMA machines.
This patch from Rusty has been sitting in my queue _forever_ but stalled
when I hit the compiler bug. Sorry about that.
Finally I also only allocate per cpu data for possible cpus, which comes
straight out of the x86-64 port. On a pseries kernel (with NR_CPUS == 128)
and 4 possible cpus we see some nice gains:
total used free shared buffers cached
Mem: 4012228 212860 3799368 0 0 162424
total used free shared buffers cached
Mem: 4016200 212984 3803216 0 0 162424
A saving of 3.75MB. Quite nice for smaller machines. Note: we now have
to be careful of per cpu users that touch data for !possible cpus.
At this stage it might be worth making the NUMA and possible cpu
optimisations generic, but per cpu init is done so early we have to be
careful that all architectures have their possible map setup correctly.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
include/asm-ppc/ had #ifdef __KERNEL__ in all header files that
are not meant for use by user space, include/asm-powerpc does
not have this yet.
This patch gets us a lot closer there. There are a few cases
where I was not sure, so I left them out. I have verified
that no CONFIG_* symbols are used outside of __KERNEL__
any more and that there are no obvious compile errors when
including any of the headers in user space libraries.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes several unnecessary fields from the paca:
- next_jiffy_update_tb was simply unused. Remove trivially.
- The exdsi exception save area was not used. There were plans to use
it, but they never seem to have gone anywhere. If they ever do, we
can put it back. Remove from the paca, and from asm-offsets.c
- The default_decr field was used from asm, but was only ever assigned
the value of tb_ticks_per_jiffy. Just access tb_ticks_per_jiffy from
asm directly instead.
Built and booted on POWER5 LPAR and iSeries RS64.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On iSeries, the paca contains, amongst other things an ItLpRegSave
structure used by the hypervisor to save registers. The hypervisor
locates this area through a pointer at the beginning of the paca, so
the structure itself can be located elsewhere. This patch moves the
reg_save area out into its own array. This reduces the amount of
iSeries specific gunk which is visible to general powerpc code via
paca.h
Built and booted on POWER5 LPAR and iSeries RS64.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves a bunch of files from arch/ppc64 and
include/asm-ppc64 which have no equivalents in ppc32 code into
arch/powerpc and include/asm-powerpc. The file affected are:
abs_addr.h
compat.h
lppaca.h
paca.h
tce.h
cpu_setup_power4.S
ioctl32.c
firmware.c
pacaData.c
The only changes apart from the move and corresponding Makefile
changes are:
- #ifndef/#define in includes updated to _ASM_POWERPC_ form
- trailing whitespace removed
- comments giving full paths removed
- pacaData.c renamed paca.c to remove studlyCaps
- Misplaced { moved in lppaca.h
Built and booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64), built
for 32-bit powermac (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Julio M. Merino Vidal