Some BIOSes don't configure HPA during boot but do so while resuming.
This causes harddrives to shrink during resume making libata detach
and reattach them. This can be worked around by unlocking HPA if old
size equals native size.
Add ATA_DFLAG_UNLOCK_HPA so that HPA unlocking can be controlled
per-device and update ata_dev_revalidate() such that it sets
ATA_DFLAG_UNLOCK_HPA and fails with -EIO when the above condition is
detected.
This patch fixes the following bug.
https://bugzilla.kernel.org/show_bug.cgi?id=15396
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Oleksandr Yermolenko <yaa.bta@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This allows parallel scan and the like to be set without having to stop
using the existing full helper functions. This patch merely adds the argument
and fixes up the callers. It doesn't undo the special cases already in the
tree or add any new parallel callers.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Traditional IDE interface sucks in that it doesn't have a reliable IRQ
pending bit, so if the controller raises IRQ while the driver is
expecting it not to, the IRQ won't be cleared and eventually the IRQ
line will be killed by interrupt subsystem. Some controllers have
non-standard mechanism to indicate IRQ pending so that this condition
can be detected and worked around.
This patch adds an optional operation ->sff_irq_check() which will be
called for each port from the ata_sff_interrupt() if an unexpected
interrupt is received. If the operation returns %true,
->sff_check_status() and ->sff_irq_clear() will be cleared for the
port. Note that this doesn't mark the interrupt as handled so it
won't prevent IRQ subsystem from killing the IRQ if this mechanism
fails to clear the spurious IRQ.
This patch also implements ->sff_irq_check() for ata_piix. Note that
this adds slight overhead to shared IRQ operation as IRQs which are
destined for other controllers will trigger extra register accesses to
check whether IDE interrupt is pending but this solves rare screaming
IRQ cases and for some curious reason also helps weird BIOS related
glitch on Samsung n130 as reported in bko#14314.
http://bugzilla.kernel.org/show_bug.cgi?id=14314
* piix_base_ops dropped as suggested by Sergei.
* Spurious IRQ detection doesn't kick in anymore if polling qc is in
progress. This provides less protection but some controllers have
possible data corruption issues if the wrong register is accessed
while a command is in progress.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Johannes Stezenbach <js@sig21.net>
Reported-by: Hans Werner <hwerner4@gmx.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Interestingly, when SIDPR is used in ata_piix, writes to DET in
SControl sometimes get ignored leading to detection failure. Update
sata_link_resume() such that it reads back SControl after clearing DET
and retry if it's not clear.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: fengxiangjun <fengxiangjun@neusoft.com>
Reported-by: Jim Faulkner <jfaulkne@ccs.neu.edu>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If ATA device failed FLUSH, it means that the device failed to write
out some amount of data and the error needs to be reported to upper
layers. As retries can't recover the lost data, FLUSH failures need to
be reported immediately in general.
However, if FLUSH fails due to transmission errors, the FLUSH needs to
be retried; otherwise, filesystems may switch to RO mode and/or raid
array may drop a drive for a random transmission glitch.
This condition can be rather easily reproduced on certain ahci
controllers which go through a PHY event after powersave mode switch +
ext4 combination. Powersave mode switch is often closely followed by
flush from the filesystem failing the FLUSH with ATA bus error which
makes the filesystem code believe that data is lost and drop to RO
mode. This was reported in the following bugzilla bug.
http://bugzilla.kernel.org/show_bug.cgi?id=14543
This patch makes libata EH retry FLUSH if it wasn't failed by the
device.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andrey Vihrov <andrey.vihrov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ->gtf_filter to ata_device and set it to ata_acpi_gtf_filter when
initializing ata_link. This is to allow quirks which apply different
gtf filters.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently libata-acpi can only filter DIPM among SATA feature enables
via _GTF. This patch adds the capability to filter out FPDMA non-zero
offset, in-order guarantee and auto-activation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We're about to add more SATA_* and ATA_ACPI_FILTER_* constants.
Reformat them in preparation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This was a hack to give userland shutdown tools time to drop manual
spindown. All popular distros updated quite some time ago and the due
is well passed. Drop it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Hopefully results in fewer on-the-wire FIS's and no breakage. We'll see!
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On certain configurations, HPA isn't or can't be unlocked during
probing but it somehow ends up unlocked afterwards. In the following
thread, the problem can be reliably reproduced after resuming from
STR. The BIOS turns on HPA during boot but forgets to do it during
resume.
http://thread.gmane.org/gmane.linux.kernel/858310
This patch updates libata revalidation such that it considers native
n_sectors. If the device size has increased to match native
n_sectors, it's assumed that HPA has been unlocked involuntarily and
the device is recognized as the same one. This should be fairly safe
while nicely working around the problem.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Christof Warlich <christof@warlich.name>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PIONEER DVD-RW DVRTD08 times out SETXFER if no media is present. The
device is SATA and simply skipping SETXFER works around the problem.
Implement ATA_HORKAGE_NOSETXFER and apply it to the device.
Reported by Moritz Rigler in the following thread.
http://thread.gmane.org/gmane.linux.ide/36790
and by Lars in bko#9540.
Updated to whine and ignore NOSETXFER if PATA component is detected as
suggested by Alan Cox.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Moritz Rigler <linux-ide@momail.e4ward.com>
Reported-by: Lars <lars21ce@gmx.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The legacy old IDE ioctl API for this is a bit primitive so we try
and map stuff sensibly onto it.
- Set PIO over DMA devices to report 32bit
- Add ability to change the PIO32 settings if the controller permits it
- Add that functionality into the sff drivers
- Add that functionality into the VLB legacy driver
- Turn on the 32bit PIO on the ninja32 and add support there
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On a timeout call a device specific handler early in the recovery so that
we can complete and process successful commands which timed out due to IRQ
loss or the like rather more elegantly.
[Revised to exclude the timeout handling on a few devices that inherit from
SFF but are not SFF enough to use the default timeout handler]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
If the device is signalling that there is data to drain after an error we
should read the bytes out and throw them away. Without this some devices
and controllers get wedged and don't recover.
Based on earlier work by Mark Lord
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ap->sector_buf is used as DMA target and should at least be aligned on
cacheline. This caused problems on some embedded machines.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata passes the returned value of dma_map_sg() to
dma_unmap_sg(),which is the misuse of dma_unmap_sg().
DMA-mapping.txt says:
To unmap a scatterlist, just call:
pci_unmap_sg(pdev, sglist, nents, direction);
Again, make sure DMA activity has already finished.
PLEASE NOTE: The 'nents' argument to the pci_unmap_sg call must be
the _same_ one you passed into the pci_map_sg call,
it should _NOT_ be the 'count' value _returned_ from the
pci_map_sg call.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This fixes problems during resume with drives that take longer than 1s to
be ready. The ATA-6 spec appears to allow 5 seconds for a drive to be
ready.
On one affected system, this patch changes "PM: resume devices took..."
message from 17 seconds to 4 seconds, and gets rid of a lot of ugly
timeout/error messages.
Without this patch, the libata code moves on after 1s, tries to send a
soft reset (which the drive doesn't see because it isn't ready) which also
times out, then an IDENTIFY command is sent to the drive which times out,
and finally the error handler will try to send another hard reset which
will finally get things working.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
3Gbps is often much more prone to transmission failures. It's usually
okay to let EH handle speed down after transmission failures but some
WD My Book drives completely shutdown after certain transmission
failures and after it only power cycling can revive them. Combined
with the fact that external drives often end up with cable assembly
which is longer than usual and more likely to have intervening gender,
this makes these drives very likely to shutdown under certain
configurations virtually rendering them unusable.
This patch implements HOARKGE_1_5_GBPS and applies it to WD My Book
such that 1.5Gbps is forced once the device is identified.
Please take a look at the following bz for related reports.
http://bugzilla.kernel.org/show_bug.cgi?id=9913
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dev->ering used to be cleared together with the rest of ata_device in
ata_dev_init() which is called whenever a probing event occurs.
dev->ering is about to be used to track probing failures so it needs
to remain persistent over multiple porbing events. This patch
achieves this by doing the following.
* Instead of CLEAR_OFFSET, define CLEAR_BEGIN and CLEAR_END and only
clear between BEGIN and END. ering is moved after END. The split
of persistent area is to allow hotter items remain at the head.
* ering is explicitly cleared on ata_dev_disable() and when device
attach succeeds. So, ering is persistent throug a device's life
time (unless explicitly cleared of course) and also through periods
inbetween disablement of an attached device and successful detection
of the next one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce new libata flags ATA_FLAG_NO_POWEROFF_SPINDOWN and
ATA_FLAG_NO_HIBERNATE_SPINDOWN that, if set, will prevent disks from
being spun off during system power off and hibernation, respectively
(to handle the hibernation case we need the new system state
SYSTEM_HIBERNATE_ENTER that can be checked against by libata, in
analogy with SYSTEM_POWER_OFF).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The forthcoming OCTEON SOC Compact Flash driver needs an additional
timing value that was not available in the ata_timing table. I add a
new column for dmack_hold time. The values were obtained from the
Compact Flash specification Rev 4.1.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
for SAS drivers.
Caught by Ke Wei (and team?) at Marvell.
Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the
general trend.
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds a per host flag that allows drivers to opt in into
having its busses scanned in parallel.
Drivers that do not set this flag get their ports scanned in
the "original" sequence.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This matters for some controllers and in one or two cases almost doubles
PIO performance. Add a bmdma32 operations set we can inherit and activate
it for some controllers
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_port_detach() first made sure EH saw ATA_PFLAG_UNLOADING and then
assumed EH context belongs to it and performed detach operation
itself. However, UNLOADING doesn't disable all of EH and this could
lead to problems including triggering WARN_ON()'s in EH path.
This patch makes port detach behave more like other EH actions such
that ata_port_detach() requests EH to detach and waits for completion.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There currently are the following looping constructs.
* __ata_port_for_each_link() for all available links
* ata_port_for_each_link() for edge links
* ata_link_for_each_dev() for all devices
* ata_link_for_each_dev_reverse() for all devices in reverse order
Now there's a need for looping construct which is similar to
__ata_port_for_each_link() but iterates over PMP links before the host
link. Instead of adding another one with long name, do the following
cleanup.
* Implement and export ata_link_next() and ata_dev_next() which take
@mode parameter and can be used to build custom loop.
* Implement ata_for_each_link() and ata_for_each_dev() which take
looping mode explicitly.
The following iteration modes are implemented.
* ATA_LITER_EDGE : loop over edge links
* ATA_LITER_HOST_FIRST : loop over all links, host link first
* ATA_LITER_PMP_FIRST : loop over all links, PMP links first
* ATA_DITER_ENABLED : loop over enabled devices
* ATA_DITER_ENABLED_REVERSE : loop over enabled devices in reverse order
* ATA_DITER_ALL : loop over all devices
* ATA_DITER_ALL_REVERSE : loop over all devices in reverse order
This change removes exlicit device enabledness checks from many loops
and makes it clear which ones are iterated over in which direction.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some recent Seagate harddrives have firmware bug which causes FLUSH
CACHE to timeout under certain circumstances if NCQ is being used.
This can be worked around by disabling NCQ and fixed by updating the
firmware. Implement ATA_HORKAGE_FIRMWARE_UPDATE and blacklist these
devices.
The wiki page has been updated to contain information on this issue.
http://ata.wiki.kernel.org/index.php/Known_issues
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch reverts the following three commits which convert libata to
use block layer tagging.
43a49cbdf3e013e13bf62fca5ccf97
Although using block layer tagging is the right direction, due to the
tight coupling among tag number, data structure allocation and
hardware command slot allocation, libata doesn't work correctly with
the current conversion.
The biggest problem is guaranteeing that tag 0 is always used for
non-NCQ commands. Due to the way blk-tag is implemented and how SCSI
starts and finishes requests, such guarantee can't be made. I'm not
sure whether this would actually break any low level driver but it
doesn't look like a good idea to break such assumption given the
frailty of ATA controllers.
So, for the time being, keep using the old dumb in-libata qc
allocation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axobe <jens.axboe@oracle.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
libata always uses PIO for ATAPI commands when the number of bytes to
transfer isn't multiple of 16 but quantum DAT72 chokes on odd bytes
PIO transfers. Implement a horkage to skip the mod16 check and apply
it to the quantum device.
This is reported by John Clark in the following thread.
http://thread.gmane.org/gmane.linux.ide/34748
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: John Clark <clarkjc@runbox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata currently imposes a UDMA5 max transfer rate and 200 sector max
transfer size for SATA devices that sit behind a pata-sata bridge. Lots
of devices have known good bridges that don't need this limit applied.
The MTRON SSD disks are such devices. Transfer rates are increased by
20-30% with the restriction removed.
So add a "blacklist" entry for the MTRON devices, with a flag indicating
that the bridge is known good.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata currently has a pretty dumb ATA_MAX_QUEUE loop for finding
a free tag to use. Instead of fixing that up, convert libata to
using block layer tagging - gets rid of code in libata, and is also
much faster.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ATA_EHI_NO_AUTOPSY and ATA_EHI_QUIET are used to control the behavior
of EH. As only the master link is visible outside EH, these flags are
set only for the master link although they should also apply to the
slave link, which causes spurious EH messages during probe and
suspend/resume.
This patch transfers those two flags to slave ehc.i before performing
slave autopsy and reporting.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
reduce size by 8 bytes from 1160 to 1152 allowing it to fit in 1 fewer
cachelines.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On user request (through sysfs), the IDLE IMMEDIATE command with UNLOAD
FEATURE as specified in ATA-7 is issued to the device and processing of
the request queue is stopped thereafter until the specified timeout
expires or user space asks to resume normal operation. This is supposed
to prevent the heads of a hard drive from accidentally crashing onto the
platter when a heavy shock is anticipated (like a falling laptop
expected to hit the floor). In fact, the whole port stops processing
commands until the timeout has expired in order to avoid any resets due
to failed commands on another device.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Explanation taken from the comment of ata_slave_link_init().
In libata, a port contains links and a link contains devices. There
is single host link but if a PMP is attached to it, there can be
multiple fan-out links. On SATA, there's usually a single device
connected to a link but PATA and SATA controllers emulating TF based
interface can have two - master and slave.
However, there are a few controllers which don't fit into this
abstraction too well - SATA controllers which emulate TF interface
with both master and slave devices but also have separate SCR
register sets for each device. These controllers need separate links
for physical link handling (e.g. onlineness, link speed) but should
be treated like a traditional M/S controller for everything else
(e.g. command issue, softreset).
slave_link is libata's way of handling this class of controllers
without impacting core layer too much. For anything other than
physical link handling, the default host link is used for both master
and slave. For physical link handling, separate @ap->slave_link is
used. All dirty details are implemented inside libata core layer.
From LLD's POV, the only difference is that prereset, hardreset and
postreset are called once more for the slave link, so the reset
sequence looks like the following.
prereset(M) -> prereset(S) -> hardreset(M) -> hardreset(S) ->
softreset(M) -> postreset(M) -> postreset(S)
Note that softreset is called only for the master. Softreset resets
both M/S by definition, so SRST on master should handle both (the
standard method will work just fine).
As slave_link excludes PMP support and only code paths which deal with
the attributes of physical link are affected, all the changes are
localized to libata.h, libata-core.c and libata-eh.c.
* ata_is_host_link() updated so that slave_link is considered as host
link too.
* iterator extended to iterate over the slave_link when using the
underbarred version.
* force param handling updated such that devno 16 is mapped to the
slave link/device.
* ata_link_on/offline() updated to return the combined result from
master and slave link. ata_phys_link_on/offline() are the direct
versions.
* EH autopsy and report are performed separately for master slave
links. Reset is udpated to implement the above described reset
sequence.
Except for reset update, most changes are minor, many of them just
modifying dev->link to ata_dev_phys_link(dev) or using phys online
test instead.
After this update, LLDs can take full advantage of per-dev SCR
registers by simply turning on slave link.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement __ata_port_next_link() and reimplement
__ata_port_for_each_link() and ata_port_for_each_link() using it.
This removes relatively large inlined code and makes iteration easier
to extend.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Logically, SCR access ops should take @link; however, there was no
compelling reason to convert all SCR access ops when adding @link
abstraction as there's one-to-one mapping between a port and a non-PMP
link. However, that assumption won't hold anymore with the scheduled
addition of slave link.
Make SCR access ops per-link.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dave Müller sent a diff for the pata_oldpiix that highlighted a problem
where a lot of the ATA drivers assume dma_mode == 0 means "no DMA" while
the core code uses 0xFF.
This turns out to have other consequences such as code doing >= XFER_UDMA_0
also catching 0xFF as UDMAlots. Fortunately it doesn't generally affect
set_dma_mode, although some drivers call back into their own set mode code
from other points.
Having been through the drivers I've added helpers for using_udma/using_mwdma
dma_enabled so that people don't open code ranges that may change (eg if UDMA8
appears somewhere)
Thanks to David for the initial bits
[and added fix for pata_oldpiix from and signed-off-by Dave Mueller
<dave.mueller@gmx.ch> -jg]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Save SControl during probing and restore it on detach. This prevents
adjustments made by libata drivers to seep into the next driver which
gets attached (be it a libata one or not).
It's not clear whether SControl also needs to be restored on suspend.
The next system to have control (ACPI or kexec'd kernel) would
probably like to see the original SControl value but there's no
guarantee that a link is gonna keep working after SControl is adjusted
without a reset and adding a reset and modified recovery cycle soley
for this is an overkill. For now, do it only for detach.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement force params nohrst, nosrst and norst. This is to work
around reset related problems and ease debugging.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- Add support for the RDC 1010 variant
- Rework the core library to have a read_id method. This allows the hacky
bits of it821x to go and prepares us for pata_hd
- Switch from WARN to BUG in ata_id_string as it will reboot if you get
it wrong so WARN won't be seen
- Allow the issue of command 0xFC on the 821x. This is needed to query
rebuild status.
- Tidy up printk formatting
- Do more ident rewriting on RAID volumes to handle firmware provided
ident data which is rather wonky
- Report the firmware revision and device layout in RAID mode
- Don't try and disable raid on the 8211 or RDC - they don't have the
relevant bits
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add Enclosure Management support to libata and ahci.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo