The atl1 driver tries to determine the MAC address thusly:
- If an EEPROM exists, read the MAC address from EEPROM and
validate it.
- If an EEPROM doesn't exist, try to read a MAC address from
SPI flash.
- If that fails, try to read a MAC address directly from the
MAC Station Address register.
- If that fails, assign a random MAC address provided by the
kernel.
We now have a report of a system fitted with an EEPROM containing all
zeros where we expect the MAC address to be, and we currently handle
this as an error condition. Turns out, on this system the BIOS writes
a valid MAC address to the NIC's MAC Station Address register, but we
never try to read it because we return an error when we find the all-
zeros address in EEPROM.
This patch relaxes the error check and continues looking for a MAC
address even if it finds an illegal one in EEPROM.
Signed-off-by: Radu Cristescu <advantis@gmx.net>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Keep enc28j60 chips in low-power mode when they're not in use.
At typically 120 mA, these chips run hot even when idle; this
low power mode cuts that power usage by a factor of around 100.
This version provides a generic routine to poll a register until
its masked value equals some value ... e.g. bit set or cleared.
It's basically what the previous wait_phy_ready() did, but this
version is generalized to support the handshaking needed to
enter and exit low power mode.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Minor bugfixes to the enc28j60 driver ... wrong section marking,
indentation, and bogus use of spi_bus_type.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Downloading firmware in pci probe allows recovery in case of
firmware failure by reloading the driver.
Also reduced delays in firmware load.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
o Remove unnecessary debug prints and functions.
o Explicitly specify pci class (0x020000) to avoid enabling
management function.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Store physical port number in netxen_adapter structure.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This fixes a the issue where logical port number is set incorrectly
for HP blade mezz cards.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ibm_newemac driver requires ether_crc to be defined. Apparently it is
possible to generate a .config without CONFIG_CRC32 set which causes the
following link errors if IBM_NEW_EMAC is selected:
LD .tmp_vmlinux1
drivers/built-in.o: In function `emac_hash_mc':
core.c:(.text+0x2f524): undefined reference to `crc32_le'
core.c:(.text+0x2f528): undefined reference to `bitrev32'
make: *** [.tmp_vmlinux1] Error 1
This patch has IBM_NEW_EMAC select CRC32 so we don't hit this error.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This fixes the most obvious 64-bit problems, but it is still very very
broken in other aspects.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three major portions to this change:
1) Add IW_EV_COMPAT_LCP_LEN, IW_EV_COMPAT_POINT_OFF,
and IW_EV_COMPAT_POINT_LEN helper defines.
2) Delete iw_stream_check_add_*(), they are unused.
3) Add iw_request_info argument to iwe_stream_add_*(), and use it to
size the event and pointer lengths correctly depending upon whether
IW_REQUEST_FLAG_COMPAT is set or not.
4) The mechanical transformations to the drivers and wireless stack
bits to get the iw_request_info passed down into the routines
modified in #3. Also, explicit references to IW_EV_LCP_LEN are
replaced with iwe_stream_lcp_len(info).
With a lot of help and bug fixes from Masakazu Mokuno.
Signed-off-by: David S. Miller <davem@davemloft.net>
This causes the suni driver to oops if you try to use sonetdiag to get
the statistics. Also add the corresponding phy->stop call to fix another
oops if you try to remove the module.
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced by the new helper ieee80211_has_morefrags which is
more consistent with the intent of the function.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few general categories:
1) ieee80211_has_* tests if particular fctl bits are set, the helpers are de
in the same order as the fctl defines:
A combined _has_a4 was also added to test when both FROMDS and TODS are set.
2) ieee80211_is_* is meant to test whether the frame control is of a certain
ftype - data, mgmt, ctl, and two special helpers _is_data_qos, _is_data_pres
which also test a subset of the stype space.
When testing for a particular stype applicable only to one ftype, functions
like ieee80211_is_ack have been added. Note that the ftype is also being
checked in these helpers. They have been added for all mgmt and ctl stypes
in the same order as the STYPE defines.
3) ieee80211_get_* is meant to take a struct ieee80211_hdr * and returns a
pointer to somewhere in the struct, see get_SA, get_DA, get_qos_ctl.
The intel wireless drivers had helpers that used this namespace, convert the
all to use the new helpers and remove the byteshifting as they were defined
in cpu-order rather than little-endian.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a shared function for transmitting the frames instead of
duplicated code in two places.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unnecessary '__constant_' prefix and use the atomic version of
ieee80211_iterate_active_interfaces().
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211_hwsim is a Linux kernel module that can be used to simulate
arbitrary number of IEEE 802.11 radios for mac80211 on a single
device. It can be used to test most of the mac80211 functionality and
user space tools (e.g., hostapd and wpa_supplicant) in a way that
matches very closely with the normal case of using real WLAN
hardware. From the mac80211 view point, mac80211_hwsim is yet another
hardware driver, i.e., no changes to mac80211 are needed to use this
testing tool.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unifies SW rf-kill flow between 4965 and 5000. It enables SW
RF-kill for 5000. This patch also solves a bug in iwl4965_mac_config:
bad mutex locking balance.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch removes 4965 prefix from iwl4965_ucode.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch returns channel list to sysfs.
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce amount of kmalloc/kfree calls in set/get_oid by preallocating command
buffer.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wlan used kmalloc to allocate private data structure and leaving data
uninitialized, but later assumed to be set zero.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the iwlcore_low_level_notify. The
notification chain is not required in this level.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up iwlwifi's code: Add missing include, remove empty
lines etc...
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes the problem that software rf_kill messes up the
card status when it is disabled if the interface is down.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes iwl4965_calc_db_from_ratio which is dead code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl4965_get_tempearture to iwl4965_hw_get_temperature
and replaces usage of original iwl4965_hw_get_temperature by
direct access to priv->temperature.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl4965_rf_kill_ct_config to iwl-core.c.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch
1. cleans up scanning code.
2. It adds round robin of TX antannas/chains.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves rate helpers to iwlcore.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves scan code to iwl-scan.c file in iwlcore module.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a check for bad length in set key flow. This solves the
Oops reported by Thomas Backlund, Joonwoo Park and Ian Schram.
It also adds some debug printing that can be useful.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch
1. Refactors settings of tx power
2. enables iwconfig txpower <value>
3. adds 5000 HW tx power
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch refactors tx aggregation respnse flow
and fixes bug revealed by tx_info to cb patch
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix allows to move between modes (ad-hoc to managed, and vice versa).
Since mode changes can only be done while driver is down, check for ibss
support can only be made when the channel is set (afte the driver goes up).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables ibss mode. It consists of two changes upon entering ibss
mode:
1. Removing the redundant line which clears the driver's station table.
This line creates a discrepancy between the driver and the FW's station
table. This prevented the generation of beacons.
2. Assigning a default value to priv's assoc_id. Normally given by an AP in
STA mode, this field is used as an indication for association. Being 0,
it prevented normal TX flow.
3. Remove a redundant ADD_STA command that cause uCode error.
4. Delay the set_mode until after the uCode is ready.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clear STATUS_FW_ERROR in the _up_ flow before reseting NIC.
UP flow will otherwise call restart again causing endless restart loop.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes SW RF-kill. If we resumed from S3 state with SW RF-kill
set, the driver wouldn't be able to remove SW RF-kill. This patch fixes
this.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes uCode log print to for easier parsing.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is wrong to set the rxon channel according to the ht-channel
in case there is a mismatch (e.g. when there is no ht).
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes redundant flags regarding to FAT channel. Use
mac80211's flag instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes IEEE80211_CHAN_W_RADAR_DETECT flag.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix opens back the aggregation decision path for iwlwifi.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch switches the use of internal iwlwifi structure with
ieee80211_conf in order to examine ht rate capabilities.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds TX aggregation handler for 5000 HW.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch maps sw and hw queues (for aggregations), so the right
mac80211 queue will be waken when ieee80211_wake_queue is invoked.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the possibility to disable the tx_power calibration.
In 5000 HW, this calibration is implemented in uCode, hence, it is
disabled in driver by default.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes some clean up in setup/cancel_deferred_work.
iwl_setup_deferred_work does the work that is common to 4965
and 5000, then it calls to HW specific handlers.
This patch also removes uneeded work_struct from iwl_priv.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the possibility not to compile the run time
calibrations. It also renames priv->sensitivity_work to
priv->run_time_calib_work, and moves bg_run_time_calib to iwl4965_base
since it is common to both: 4965 and 5000.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helps against lost interrupts and aids in debugging this.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes CONFIG_IWL4965_HT #ifdefs for iwl 4965 and 5000. 11n
feature is stable in those drivers and its mode of operation is determined
in mac80211, so this dependency is not needed any more.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mixed use of 'dev' and 'usbdev' for usbnet pointer can be confusing. So changing all 'usbnet *dev' to 'usbnet *usbdev'.
Also remove 'net_device *net' pointer from 'rndis_wext_bind' as 'usbdev->net' were already used where needed.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't queue set_multicast_list work if WORK_SET_MULTICAST_LIST
flag already set.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver wasn't updating netif_carrier on link state changes but assumed
link layer was always up.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wext_link_change() is called from within rndis_command() so it
isn't very good place to do any work. Move to worker thread.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rework the alignment check in rt2x00dev.c to be independent of any
potential alignment measures that may be taken before. Just check
whether the payload is aligned based on the pointer addresses.
Note: This is preparatory for the dynamically mapped skb buffers
for the PCI drivers, as these need 4-byte alignment instead of the
currently enforced offset by 2 bytes.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MAX_RX_SSI and MAX_NOISE are no longer used,
it is better to remove them entirely.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For RTS/CTS-to-self frames the IEEE80211_TX_CTL_USE_RTS_CTS flag
should be cleared for the tx_info flags.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To really force the FIELD macros to determine
the first bit of the register field we should
use the __builtin_choose_expr() function.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not safe to use the skb->cb area for both the rxd and
skb_frame_desc data at the same time, while they occupy an overlapping
piece of memory. This can lead to hard to trace crashes as pointers
within skb_frame_desc are pointing into nowhere, or the rxd data is
overwritten with non-sense.
Fix it by copying the rxd to a small buffer on the stack.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rt2x00pci will be switched over to dynamically mapped skb's
instead of statically allocated DMA buffers, it no longer can handle
alignment of RX packets in a copy step, and needs to implement the
same scheme as rt2x00usb does.
In order to make the patch on dynamically mapped skb's smaller,
already centralize the alignment handling into rt2x00lib. This allows
us to move more code in rt2x00lib, and thus remove code duplication
between rt2x00usb and rt2x00pci.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The data and data_len fields aren't really necessary in struct
skb_frame_desc, as they can be deduced from the skb itself.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX queues shouldn't be kicked after each frame that is put into the
queue. This could cause problems during RTS and CTS-to-self as well
as with fragmentation. In all those cases you want all frames to be
send out in a single burst. Off course we shouldn't let the queue fill
up entirely, thus we introduce a 10% threshold which, when reached,
will force the frames to be send out regardless of the frame.
In addition we should prevent queues to become full in such a way
that the tx() handler can fail. Instead of stopping the queue when
it is full, we should stop it when it is below the threshold.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The write_tx_data functions in rt2x00pci and rt2x00usb have
a lot in common. This moves that duplicate code into
rt2x00queue_write_tx_frame().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00usb_kick_tx_queue() will loop over all entries
within the INDEX_DONE->INDEX range and kick each entry
which is pending to be kicked. This makes the kick_tx_queue
approach work the same as with the PCI drivers which
will allow for more code generalisation into rt2x00lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
qid should be initialized to QID_BEACON and QID_ATIM
for the beacon and atim quue. This makes checking for
a particular queue much saner, and it shouldn't harm,
because the only places where the value is send to
the hardware, we are allowed to send any value we
want since it is only used as argument in the
TX done register.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2x00_set_field functions are very often used,
but GCC is better able to optimize them when they
are macros instead of static inline functions.
After changing it to macro's each rt2x00 driver will
loose about ~3500 bytes in size.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00usb doesn't need the TX descriptor in the TX done path.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 doesn't send RTS or CTS-to-self frames through
the tx() callback functions so we don't need to check it.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce code duplication by moving led structure initialization
into a per-driver function.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Reduce goto usage
* Mark if-statements which are true on hardware error unlikely()
* Cleanup debug messages
This makes the code look nicer and be better optimized since
the chance of hardware errors should be very small.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By using __ffs() the register offsets were always calculated
at run-time which all FIELD32/FIELD16 definitions were builtin
constants. This means we can heavily optimize the register handling
by allowing GCC to do all the work during compilation.
Add some compile_ffs() macros to perform the calculation at
compile time. After this each rt2x00 module size is reduced
by ~2500 bytes. And the stack size of several functions is reduced
as well which further limits the number of rt2x00 results in
'make checkstack'.
v2: Merge GertJan's bugfix of patch [1/11] directly into this patch
instead of providing it as seperate patch.
v3: Add extra parentheses when bitshifting __x
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes setting the coherent DMA mask for PCI devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Config symbols that select LEDS_CLASS need to depend on NEW_LEDS so that
undefined symbols are not used in the build.
The alternative is to select NEW_LEDS, which some drivers do.
This patch fixes the led_* symbols build errors.
(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Config symbols that select RFKILL need to depend on INPUT so that
undefined symbols are not used in the build.
This patch fixes the input_* symbols build errors.
(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes a WARN_ON that is responsible for the following koops:
http://www.kerneloops.org/searchweek.php?search=b43_generate_noise_sample
The comment in the patch describes why it's safe to simply remove
the check.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a possible NULL pointer dereference in an error path of the
DMA allocation error checking code. This is also necessary for a future
DMA API change that is on its way into the mainline kernel that adds
an additional dev parameter to dma_mapping_error().
This patch moves the whole struct b43_dmaring struct initialization
right before any DMA allocation operation.
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
None of the rt2x00 PCI devices support 64-bit DMA addresses (they all
only accept 32-bit buffer addresses). Hence it makes no sense to try to
enable 64-bit DMA addresses. Only try to enable 32-bit DMA addresses.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a "BUG: unable to handle kernel paging request"
bug in rt73usb which was caused by killing the guardian_urb
while it had never been allocated for rt73usb.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: Workaround HW bug for SB600/700 SATA controller PMP support
ahci: workarounds for mcp65
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
tcp: Revert 'process defer accept as established' changes.
ipv6: Fix duplicate initialization of rawv6_prot.destroy
bnx2x: Updating the Maintainer
net: Eliminate flush_scheduled_work() calls while RTNL is held.
drivers/net/r6040.c: correct bad use of round_jiffies()
fec_mpc52xx: MPC52xx_MESSAGES_DEFAULT: 2nd NETIF_MSG_IFDOWN => IFUP
ipg: fix receivemode IPG_RM_RECEIVEMULTICAST{,HASH} in ipg_nic_set_multicast_list()
netfilter: nf_conntrack: fix ctnetlink related crash in nf_nat_setup_info()
netfilter: Make nflog quiet when no one listen in userspace.
ipv6: Fail with appropriate error code when setting not-applicable sockopt.
ipv6: Check IPV6_MULTICAST_LOOP option value.
ipv6: Check the hop limit setting in ancillary data.
ipv6 route: Fix route lifetime in netlink message.
ipv6 mcast: Check address family of gf_group in getsockopt(MS_FILTER).
dccp: Bug in initial acknowledgment number assignment
dccp ccid-3: X truncated due to type conversion
dccp ccid-3: TFRC reverse-lookup Bug-Fix
dccp ccid-2: Bug-Fix - Ack Vectors need to be ignored on request sockets
dccp: Fix sparse warnings
dccp ccid-3: Bug-Fix - Zero RTT is possible
There is one bug in ATI SATA PMP of SB600 and SB700 old revision, which leads
to soft reset failure. This patch can fix the bug.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MCP65 ahci can do NCQ but doesn't set the CAP bit and rev A0 and A1
can't do MSI but have MSI capability. Implement AHCI_HFLAG_YES_NCQ
and apply appropriate workarounds.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ramtron FM3130 is a chip with two separate devices inside, RTC clock and
FRAM. This driver provides only RTC functionality.
This chip is met in lots of custom boards with AT91SAMXXXX CPU I work
with, is cheap and in no way better or worse than any other RTC on market.
While it is mostly met on much smaller devices, I think it is great to
have it supported in Linux.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More Kconfig tweaks related to the legacy PC RTC code:
- Describe the legacy PC RTC driver as such ... it's never quite
been clear that this driver is for PC RTCs, and now it's fair
to call this the "legacy" driver.
- Force it to understand about HPET stealing its IRQs ... kernel
code does this always when HPET is in use, there should be no
option for users to goof up the config.
This seems to fix kernel bugzilla #10729.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently (around 2.6.25) I've noticed that RTC no longer works for me. It
turned out this is because I use pnpacpi=off kernel option to work around
the parport_pc bugs. I always did so, but RTC used to work fine in the
past, and now it have regressed.
The patch fixes the problem by creating the platform device for the RTC
when PNP is disabled. This may also help running the PNP-enabled kernel
on an older PCs.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Cc: David Brownell <david-b@pacbell.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several console keyboard maps are broken since
commit 04c7197650
Author: Samuel Thibault <samuel.thibault@ens-lyon.org>
Date: Tue Oct 16 23:27:04 2007 -0700
unicode diacritics support
because that changeset made k_self consider the value as a latin1
character when in Unicode mode, which is wrong; k_self should still take
the console map into account.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The generic nvram driver announces itself as
'Macintosh non-volatile memory driver'
instead of 'Generic non-volatile memory driver'. Fix that.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the cirrusfb driver, the RAM address printk has a superfluous 'x' that
could be interpreted as "don't care", while it is actually a typo. Fix
that.
[akpm@linux-foundation.org: join the two printk strings to make it atomic]
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since many distros load this driver by default (throw it against the wall
and see what sticks method). Change the error message severity level to
avoid alarming users. Isn't it annoying when users actually read the
error logs...
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Cc: Michael Buesch <mb@bu3sch.de>
Acked-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
spid has been allocated in this function and so should be freed before
leaving it, as in the other error handling cases.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
@r exists@
expression E,E1;
statement S;
position p1,p2,p3;
@@
E =@p1 \(kmalloc\|kcalloc\|kzalloc\)(...)
... when != E = E1
if (E == NULL || ...) S
... when != E = E1
if@p2 (...) {
... when != kfree(E)
}
... when != E = E1
kfree@p3(E);
@forall@
position r.p2;
expression r.E;
int E1 != 0;
@@
* if@p2 (...) {
... when != kfree(E)
when strict
return E1; }
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With CONFIG_DEBUG_SHIRQ set we will get an interrupt as soon as we
allocate one. Tasklets may be scheduled in the interrupt handler but they
will be initialized after the handler returns, causing a BUG() in
kernel/softirq.c when they run.
Should fix this Fedora bug report:
https://bugzilla.redhat.com/show_bug.cgi?id=449817
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alarm->pending indicates whether there's an alarm that has actually been
triggered, not whether we're waiting for it. alarm->enabled indicates
that.
Also add missing locking around reading the RTC registers.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the next generation of HP Smart Array SAS/SATA
controllers. Shipping date is late Fall 2008.
Bump the driver version to 3.6.20 to reflect the new hardware support from
patch 1 of this set.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Release ports which are requested during detection which are not freed if
there is no hga card. Otherwise there is a crash during cat /proc/ioports
command.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I would like to thank Eliezer Tamir for writing and maintaining the
driver for the past two years. I will take over maintaining the bnx2x
driver from now on.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a compile failure in 2.6.26-rc5-git5.
The variable is expected to be called ofdev.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the RTNL is held when we invoke flush_scheduled_work() we could
deadlock. One such case is linkwatch, it is a work struct which tries
to grab the RTNL semaphore.
The most common case are net driver ->stop() methods. The
simplest conversion is to instead use cancel_{delayed_}work_sync()
explicitly on the various work struct the driver uses.
This is an OK transformation because these work structs are doing
things like resetting the chip, restarting link negotiation, and so
forth. And if we're bringing down the device, we're about to turn the
chip off and reset it anways. So if we cancel a pending work event,
that's fine here.
Some drivers were working around this deadlock by using a msleep()
polling loop of some sort, and those cases are converted to instead
use cancel_{delayed_}work_sync() as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
On some boards, the mv643xx_eth MAC isn't connected to a PHY but
directly (via the MII/GMII/RGMII interface) to another MAC-layer
device. This patch allows specifying ->phy_addr = -1 to skip all
PHY-related initialisation and run-time poking in that case.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
During OOM, instead of stopping RX refill when the rx desc ring is
not empty, keep trying to refill the ring as long as it is not full
instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Some SoCs have the TX bandwidth control registers in a slightly
different place. This patch detects that case at run time, and
re-directs accesses to those registers to the proper place at
run time if needed.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Newer hardware has a 16-bit instead of a 14-bit RX coalescing
count field in the SDMA_CONFIG register. This patch adds a run-time
check for which of the two we have, and adjusts further writes to the
rx coal count field accordingly.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Under some conditions, the TXQ ('TX queue being served') bit can clear
before all packets queued for that TX queue have been transmitted.
This patch enables TXend interrupts, and uses those to re-kick TX
queues that claim to be idle but still have queued descriptors from
the interrupt handler.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
As with the multiple RX queue support, allow the platform code to
specify that the hardware we are running on supports multiple TX
queues. This patch only uses the highest-numbered enabled queue
to send packets to for now, this can be extended later to enable
QoS and such.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Allow the platform code to specify that we are running on hardware
that is capable of supporting multiple RX queues. If this option
is used, initialise all of the given RX queues instead of just RX
queue zero.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Add an interface for the hardware's per-port and per-subqueue
TX rate control. In this stage, this is mainly so that we can
disable the bandwidth limits during initialisation of the port.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
General cleanup of the mv643xx_eth driver. Mainly fixes coding
style / indentation issues, get rid of some useless 'volatile's,
kill some more superfluous comments, and such.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Remove the write-only ->[rt]x_int_coal members from struct
mv643xx_eth_private. In the process, tweak the RX/TX interrupt
mitigation code so that it is compiled by default, and set the
default coalescing delays to 0 usec.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Split all TX queue related state into 'struct tx_queue', in
preparation for multiple TX queue support.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Split all RX queue related state into 'struct rx_queue', in
preparation for multiple RX queue support.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The per-port mv643xx_eth_private struct had a private instance
of struct net_device_stats that was never ever written to, only
read (via the ethtool statistics interface). This patch gets
rid of the private instance, and tweaks the ethtool statistics
code in mv643xx_eth to use the statistics in struct net_device
instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Since they are no longer used, kill enum FUNC_RET_STATUS and
struct pkt_info (which were a rather roundabout way of communicating
RX/TX status within the same driver).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
rx_return_buff() is also a remnant of the HAL layering that the
original mv643xx_eth driver used. Moving it into its caller kills
the last reference to FUNC_RET_STATUS/pkt_info.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The port_receive() function is a remnant of the original mv643xx_eth
HAL split. This patch moves port_receive() into its caller, so that
the top and the bottom half of RX processing no longer communicate
via the HAL FUNC_RET_STATUS/pkt_info mechanism abstraction anymore.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Half of the functions in the mv643xx_eth driver are prefixed by
useless and baroque comment blocks on _what_ those functions do (which
is obvious from the code itself) rather than why, and there's no point
in keeping those comments around.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
A bunch of places in the mv643xx_eth driver use the 'mv643xx_'
prefix. Since the mv643xx is a chip that includes more than just
ethernet, this patch makes all those places use either no prefix
(for some internal-use-only functions), or the full 'mv643xx_eth_'
prefix.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The fact that mv643xx_eth is an ethernet driver is pretty obvious,
and having a lot of internal-use-only functions and defines prefixed
with ETH_/ethernet_/eth_ prefixes is rather pointless. So, get rid
of most of those prefixes.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Remove the unused rx/tx descriptor field defines, and move the ones
that are actually used to the actual definitions of the rx/tx
descriptor format.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
All except one of the port serial status register bit defines are
unused -- kill the unused ones.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The only user of the ETH_MIB_VERY_LONG_NAME_HERE defines is the
eth_update_mib_counters() function. Get rid of the defines by
open-coding the register offsets in the latter.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Get rid of RX_BUF_OFFSET (which is synonymous with ETH_HW_IP_ALIGN).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Replace the nondescriptive names ETH_INT_UNMASK_ALL and
ETH_INT_UNMASK_ALL_EXT by names of the actual fields being masked
and unmasked in the various writes to the interrupt mask registers.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
None of the port status register bit defines are ever used in the
mv643xx_eth driver -- nuke them all.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Over half of the port serial control register bit defines are never
used, and the PORT_SERIAL_CONTROL_DEFAULT_VALUE define is never used
either. Keep only those defines that are actually used.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Delete the defines for SDMA config register bit values that are
never used in the driver, to tidy up the code some more.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The port config extend register is never changed at run time.
Document the meaning of the initial value, and delete the defines
for the individual bits in this register.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The mv643xx_eth driver only ever changes bit 0 of the port config
register at run time, the rest of the register bits are fixed (and
always zero). Document the meaning of the chosen default value,
and get rid of all the defines for each of the individual bits.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Shorten the various oversized register names in mv643xx_eth.c, to
increase readability.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
This patch performs a reverse topological sort of all functions in
mv643xx_eth.c, so that we can get rid of all forward declarations,
and end up with a more understandable driver due to related functions
being grouped together.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
This patch removes CVS keyword that weren't updated for a long time.
One of them was printed as part of a printk, which also doesn't make
much sense for a 5 year old and no longer updated keyword.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compared to other places in the kernel, I think that this driver misuses
the function round_jiffies.
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The branches are dead code. even when dev->flag IFF_MULTICAST (defined
0x1000) is set, dev->flags & IFF_MULTICAST & [boolean] always evaluates to
0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
From: tony@bakeyournoodle.com (Tony Breeds)
The commit 3f8cb09885
(drivers/net/lib8390: fix warning, trim trailing whitespace) removed
ei_local from ei_tx_err() and ei_rx_overrun() resulting in the following
build errors on m68k and sh:
Using /scratch1/tony/next as source for kernel
GEN /scratch1/tony/next_out/Makefile
CHK include/linux/version.h
CHK include/linux/utsrelease.h
CALL /scratch1/tony/next/scripts/checksyscalls.sh
CHK include/linux/compile.h
CC [M] drivers/net/zorro8390.o
In file included from /scratch1/tony/next/drivers/net/zorro8390.c:47:
drivers/net/lib8390.c: In function 'ei_tx_err':
drivers/net/lib8390.c:556: error: 'ei_local' undeclared (first use in this function)
drivers/net/lib8390.c:556: error: (Each undeclared identifier is reported only once
drivers/net/lib8390.c:556: error: for each function it appears in.)
drivers/net/lib8390.c: In function 'ei_rx_overrun':
drivers/net/lib8390.c:823: error: 'ei_local' undeclared (first use in this function)
make[3]: *** [drivers/net/zorro8390.o] Error 1
make[2]: *** [drivers/net] Error 2
make[1]: *** [drivers] Error 2
make: *** [sub-make] Error 2
The problem is that ei_inb_p() is using various #defines (from
drivers/net/8390.h) that use EI_SHIFT, which in some drivers on some
architectures use ei_local. Tag ei_local as "__maybe_unused" to keep it
around and keep the warnings the original commit is trying to silence
... silenced.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Using the new interface for propagating device feature flags into VLAN
devices, turn on TSO and CSUM offload on VLAN devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Using the new interface for propagating device feature flags into VLAN
deivces, turn on TSO and CSUM offload on VLAN devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Using the new interface for propagating device feature flags into VLAN
devices, turn on TSO and CSUM offload on VLAN devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This driver is for a number of different Option devices. Originally
written by Option and Andrew Bird, but cleaned up massivly for
acceptance into mainline by me and others.
Many thanks to the following for their help in cleaning up the driver by
providing feedback and patches to it:
- Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
- Oliver Neukum <oliver@neukum.org>
- Alan Cox <alan@lxorguk.ukuu.org.uk>
- Javier Marcet <javier@krausbeck.org>
Cc: Andrew Bird <ajb@spheresystems.co.uk>
Cc: Javier Marcet <javier@krausbeck.org>
Cc: Filip Aben <f.aben@option.com>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Oliver Neukum <oliver@neukum.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch makes the following needlessly global functions static:
- macsonic_init()
- mac_onboard_sonic_ethernet_addr()
- mac_onboard_sonic_probe()
- mac_nubus_sonic_ethernet_addr()
- macsonic_ident()
- mac_nubus_sonic_probe()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch removes write-only global "last_dev" variables from the
following drivers:
- a2065.c
- declance.c
- sunlance.c
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch makes the following needlessly global functions static:
- mac8390_ident()
- mac8390_testio()
- mac8390_memsize()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch makes the needlessly global hplance_{init,cleanup}_module()
static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch makes the needlessly global lance_addr_list[] static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We should use a random mac address if the EEPROM doesn't contain a valid
one. This makes life on Boards with unprogrammed EEPROM devices easier.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for Renesas SuperH Ethernet controller. This driver supports
SH7710 and SH7712.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable the smc911x driver for the SuperH architecture. While at it remove
the unused SMC_USE_SH_DMA definition.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds a new header file for platform data information
together with code that adds run time bus width and irq flag support.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch contains changes needed for platform data support:
- Move smc911x_local structure to header file
- Pass along smc911x_local structure pointer to macros
- Keep register base address in smc911x_local structure
- Remove unused ioaddr variables
[m.kozlowski@tuxland.pl: Parenthesis fix in drivers/net/smc911x.h]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes the following issues related to 16-bit support:
- Remove unused 16-bit PXA DMA implementation.
- Remove unused SMC_inw() and SMC_outw() functions.
- Fix 16-bit SMC_outl to use writew() instead of writel().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove unused SMC_inb() and SMC_outb() functions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: don't use reset-resume if drivers don't support it
USB: isp1760: Assign resource fields before adding hcd
isight_firmware: Avoid crash on loading invalid firmware
USB: fix build bug in USB_ISIGHTFW
This patch tries to identify which devices are able to accept
reset-resume handling, by checking that there is at least one
interface driver bound and that all of the drivers have a reset_resume
method defined. If these conditions don't hold then during resume
processing, the device is logicall disconnected.
This is only a temporary fix. Later on we will explicitly unbind
drivers that can't handle reset-resumes.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the bogus "io mem 0x00000000" message printed
during driver init due to hcd->rsrc_start being assigned after
the call to usb_add_hcd().
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Different tools generate slightly different formats of the isight
firmware. Ensure that the firmware buffer is not overrun, while still
ensuring that the correct amount of data is written if trailing data is
present.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Report-by: Justin Mattock <justinmattock@gmail.com>
Tested-by: Justin Mattock <justinmattock@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: fix build bug in USB_ISIGHTFW
-tip tree testing found this build bug:
drivers/built-in.o: In function `isight_firmware_load':
isight_firmware.c:(.text+0x1ade08): undefined reference to `request_firmware'
isight_firmware.c:(.text+0x1adf9c): undefined reference to `release_firmware'
select FW_LOADER in USB_ISIGHTFW.
From: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix kernel-doc for new dev_set_name() function:
Warning(lin2626-rc5//drivers/base/core.c:767): No description found for parameter 'fmt'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My laptop thinks that it's a good idea to give -73C as the critical
CPU temperature.... which isn't the best thing since it causes a shutdown
right at bootup.
Temperatures below freezing are clearly invalid critical thresholds
so just reject these as such.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes problem introduced in 20080123, with fix for Unload operator.
Parse tree object can be already deleted; must use the opcode
within the WalkState.
ACPI: kmemcheck: Caught 16-bit read from freed memory
http://bugzilla.kernel.org/show_bug.cgi?id=10669
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a problem introduced in 20080514 where the status of
execution of _SST is incorrectly returned to the caller. _SST
is optional, and if it is AE_NOT_FOUND, the exception should be
ignored.
http://www.acpica.org/bugzilla/show_bug.cgi?id=716
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts a change introduced in version 20071019. The table
is now loaded at the namespace root even though this goes against
the ACPI specification. This provides compatibility with other
ACPI implementations.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Only "SSDT" is acceptable to the ACPI spec, but tables are
seen with OEMx and null sigs. Therefore, signature validation
is worthless. Apparently MS ACPI accepts such signatures, ACPICA
must be compatible.
http://bugzilla.kernel.org/show_bug.cgi?id=10454
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Allows null field list in Field(), BankField(), and IndexField().
2.6.26-rc1 regression: ACPI fails to load SDT. - Dell M1530
http://bugzilla.kernel.org/show_bug.cgi?id=10606
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
If acpi_install_notify_handler() for a bay device fails, the bay driver is
superfluous. Most likely, another driver (like libata) is already caring
about this device anyway. Furthermore,
register_hotplug_dock_device(acpi_handle) from the dock driver must not be
called twice with the same handler. This would result in an endless loop
consuming 100% of CPU. So clean up and exit.
Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Tim Pepper <lnxninja@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds a proper prototype for acpi_processor_tstate_has_changed()
in include/acpi/processor.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This is a SLIT sanity checking patch. It moves slit_valid() function to
generic ACPI code and does sanity checking for both x86 and ia64. It sets up
node_distance with LOCAL_DISTANCE and REMOTE_DISTANCE when hitting invalid
SLIT table on ia64. It also cleans up unused variable localities in
acpi_parse_slit() on x86.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Radu Cristescu