Signed-off-by: Matt Mackall <mpm@selenic.com>
Tested-by: Anders K. Pedersen <akp@cohaesio.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
DASD allows to open a device as soon as gendisk is registered, which means the
device is a fake device (capacity=0) and we do know nothing about blocksize
and partitions at that point of time. In case the device is opened by
someone, the bdev and inode creation is done with the fake device info and the
following partition detection code is just using the wrong data.
To avoid this modify the DASD state machine to make sure that the open is
rejected until the device analysis is either finished or an unformatted device
was detected.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The message limit on the iucv connect call for the smsg module is too low.
Therefore increase the smsg message limit to 255.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We're presently getting oopses because Bluetooth (and possibly other) drivers
are calling core functions after things have been shut down.
So rather than oopsing, let's drop a warning then take avoiding action, so the
machine survives. Once all the sub-drivers are fixed up we can remove the
take-avoiding-action part.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] mca recovery return value when no bus check
[IA64] SGI SN drivers: don't report !sn2 hardware as an error
[IA64] don't report !sn2 or !summit hardware as an error
[IA64] gensparse_defconfig: turn on PNPACPI
[IA64] Increase severity of MCA recovery messages
Typos grab bag of the month.
Eyeballed by jmc@ in OpenBSD.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Workaround for Nexus CA: Debi test fails unless first debi write is repeated.
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] ip22zilog: Fix oops on runlevel change with serial console
[SERIAL] Fix two bugs in parport_serial
This stuff is all in the generic ia64 kernel, and the new initcall error
reporting complains about them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Incorrect uart_write_wakeup() calls cause reference to a NULL tty
pointer. This has been fixed in the sunsab and sunzilog serial drivers
in October 2005. Update the ip22zilog, which is based on sunzilog,
accordingly.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk
Add DMA workaround for chips that do not support full 64-bit DMA
addresses.
5714, 5715, and 5780 chips only support DMA addresses less than 40
bits. On 64-bit systems with IOMMU, set the dma_mask to 40-bit so
that pci_map_xxx() calls will map the DMA address below 40 bits if
necessary. On 64-bit systems without IOMMU, set the dma_mask to
64-bit and check for DMA addresses exceeding the limit in
tg3_start_xmit().
5788 only supports 32-bit DMA so need to set the mask appropriately
also.
Thanks to Chris Elmquist at SGI for reporting and helping to debug
the problem on 5714.
Thanks to David Miller for explaining the HIGHMEM and DMA stuff.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than checking for some known failures, check positively for the
success response code 0x0001 and return -EIO for unrecognized failure
response codes.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Greg Smith <gsmith@nc.rr.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Windfarm PID module lacks a licence, it should be GPL, here it is
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fix some compatiblity issues with big endian systems
Signed-off-by: Martin Bachem <info@colognechip.com>
Signed-off-by: Karsten Keil <kkeil@suse.de>
Cc: Al Viro <viro@ftp.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the same ttyIx device was opened by two processes the module was not
released and so the usage count went never to zero again. This oneliner fixes
the issue.
Signed-off-by: Oskar Senft <o.senft@sirrix.com>
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add new PCI IDs for HFC-S PCI based ISDN TA 'Primux II S0' and 'Primux II S0'
from Gerdes AG
Signed-off-by: Martin Bachem <info@colognechip.com>
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SCSI layer uses SCSI_SENSE_BUFFERSIZE (96) for the sense buffer
size, even though some other code uses "sizeof(struct request_sense)"
(which is 64 bytes). Allocate the buffer using the bigger of the two
for safety.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a use-after-free bug in the usb-serial core. It is simple to
trigger this (open a usb-serial port, then yank the device out before
closing the port.) Thanks to Stefan Seyfried <seife@suse.de> for
reporting this, and to the slab debugging code which enabled it to be
tracked down.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
memset() is called before check.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Steinar H. Gunderson reported:
- For some reason, it detects the 9845 as a 9735 -- it appears this is
simply related to the ordering in parport_serial_pci_tbl[]. If we move
the 9845 up above the 9735, it prints out 9710:9845, but no change in
behaviour. (We didn't find out why this was the case; we left it alone
since it didn't affect our problem.)
- The card has no parallel port (at least no physical ones), yet it reports
(via its subsystem ID of 0x0014) one parallel port and four serial ports.
The probe for the parallel port fails, and the driver just aborts. Thus,
it doesn't find the serial ports.
Fix the debugging code to use dev_dbg, but don't bother displaying the
PCI ID of the detected board (that's accessible via other means.)
Also, arrange for parport_register() to return 0 even if it finds no
ports.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a trivial compilation warning:
CC drivers/mmc/au1xmmc.o
drivers/mmc/au1xmmc.c: In function ‘au1xmmc_dma_callback’:
drivers/mmc/au1xmmc.c:743: warning: unused variable ‘status’
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/mmc/au1xmmc.c doesn't compile because commit
e92251762d introduced a typo and passes
the wrong argument to the mmc_resp_type macro.
Error because of the typo:
CC drivers/mmc/au1xmmc.o
drivers/mmc/au1xmmc.c: In function ‘au1xmmc_send_command’:
drivers/mmc/au1xmmc.c:197: warning: implicit declaration of function ‘mmc_rsp_type’
...
LD .tmp_vmlinux1
drivers/built-in.o: In function `au1xmmc_request':au1xmmc.c:(.text+0x89504): undefined reference to `mmc_rsp_type'
:au1xmmc.c:(.text+0x8968c): undefined reference to `mmc_rsp_type'
make: *** [.tmp_vmlinux1] Error 1
Error because of the wrong argument:
CC drivers/mmc/au1xmmc.o
drivers/mmc/au1xmmc.c: In function ‘au1xmmc_send_command’:
drivers/mmc/au1xmmc.c:197: error: invalid type argument of ‘->’
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/mmc/au1xmmc.c currently doesn't compile; it needs to be
converted to use platform_driver. I cannot test this change because
of lack of hardware but I followed the drivers this one is based on,
and the code is certainly not worse than before.
drivers/mmc/au1xmmc.c: At top level:
drivers/mmc/au1xmmc.c:1002: error: ‘platform_bus_type’ undeclared here (not in a function)
make[2]: *** [drivers/mmc/au1xmmc.o] Error 1
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mac_addr variable doesn't get reset between
(re)additions of multicast addresses. One byte
of all multicast addresses (except the first)
can be incorrect.
Signed-off-by: Arthur Kepner <akepner@sgi.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Almost all the code for the VIA RNG is guarded with __i386__ #ifdefs,
the only exception being the enumeration of RNG types which is used to
index into the rng_vector ops array. This patch adds an ifdef around
that for consistency and since the guard makes a difference when adding
new RNG types on non-i386 hardware.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-Off-By: Jeff Garzik <jeff@garzik.org>
- fixed tda9886 port 2 setting
- turned remote control receiver off via saa7134 GPIO to avoid i2c hangs
- modified tda9886 client calls to direct i2c access to allow proper return
to analog mode
- allow mode change to V4L2_TUNER_DIGITAL_TV in tuner VIDIOC_S_FREQUENCY
client call
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- ELSA EX-VISION 500TV was incorrectly programmed to have the same
subsystem ID as ELSA EX-VISION 300TV, (1048:226b)
- This changeset replaces the incorrect subsystem ID (1048:226b)
with the correct one (1048:226a) for the ELSA EX-VISION 500TV.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I have a TT C1500 card (saa7146, STV0297) which had problems tuning
channels at QAM128 (like the ones in the Finnish HTV / Welho network).
A fix which seems to work perfectly so far is to change the delay for
QAM128 to the same values as for QAM256 in stv0297_set_frontend(),
Signed-off-by: Mattias Nordstrom <nordstrom@realnode.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
use __devinit/__devexit/__devexit_p() where appropriate
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The probing code for tda8290 changes the state of the tda9887 GP ports.
The patch assumes that if probing for tda8290 failed, this must be a
tda9887 and restores its power on defaults.
This should solve the module load order issue with some pinnacle cards.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following are specific to lgdt3303, and are being renamed to reflect this.
- cxusb_lgdt330x_config renamed to cxusb_lgdt3303_config.
- cxusb_lgdt330x_frontend_attach renamed to cxusb_lgdt3303_frontend_attach.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When multiple cards were installed, only the first card would have
audio initialized, because only the first position in the array parameter
defaulted to "1"
To make things worse, the "enable" parameter wasn't enabled, so there
was no workaround.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds another composite input to the Pinnacle PCTV 100i
definition which filters the chrominace signal from the luma input. This
improves video quality for Composite signals on the S-Video connector of
the card.
In addition the name string of the card is changed to include PCTV 40i
and 50i since these cards are identical.
Signed-off-by: Karsten Suehring <ksuehring@gmx.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following possible cleanups:
- update the Kconfig help to mention the VP310
- merge vp310_attach and mt312_attach into a new vp310_mt312_attach
to remove some code duplication
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds a couple of printk's to windfarm_pm112 to display which
control loops are actually starting and fixes a bug where it would not
start all loops.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some of the windfarm sensor modules can initialize on old machines that
don't have full windfarm support like non-dual core desktop G5s.
Unfortunately, by doing so, they would trigger a bug in their matching
algorithm causing them to attach to the wrong bus, thus triggering
issues with the i2c core and breaking the thermal driver.
This patch fixes the probing issue (so that they will work when a
windfarm port is done to these machines) and also prevents for now
windfarm to load at all on these machines that still use therm_pm72 to
avoid wasting resources.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It fixes a bug in zfcp which provokes a race
in scsi_scan.c. Finally this can lead to an Oops like:
kernel BUG at fs/sysfs/symlink.c:87!
Correctly set this_id for the host. Otherwise we provoke
a race between scsi_target_reap_work and concurrent
scsi_add_device.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This device spews total rubbish to a REPORT LUNS command, so avoid
sending it one.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Sync up the recent redboot fix with MTD CVS. It uses the correct swab()
functions.
Cc: John Bowler <jbowler@acm.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Using this patch, Omnikey CardMan 4000 and 4040 devices automatically
get their device nodes created by udev.
Also, we now check for (and handle) failure of pcmcia_register_driver()
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The axnet_cs driver can support the AMB8110 PC Card, so add the id for it.
In the old pcmcia-cs config file, this card is listed with the comment "not
specific enough". The last entry in the axnet_ids has the same comment.
They are disabled, and for good reason as it was originally identified by
the MANFID, and that is shared with several cards that use both the
pcnet_cs driver and axnet_cs driver. I tried my AMB8110 with pcnet_cs, and
found that it works fine, and I cannot find a reason for either, except
that the old config file recommended axnet_cs.
Signed-off-by: Jesse Allen <the3dfxdude@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Don't just use cards with PCMCIA ID 0x0156, 0x0002. Make sure that the
vendor string is "Intersil" or "INTERSIL"
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The second pseudo multi-function device of a PCMCIA card may only be
configured once the first one is initialized. Therefore, delay the
registration of the second device until the first one is initialized.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net
Comment out debug code in tty receive buffering. For performance reasons
(I'll keep it enabled in -mm).
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is Adam's pnp probing fix. It's been reported to fix hangs on several
people's machines. I don't know if it's official or final, and Adam isn't
contactable at present. But I'm not aware of the patch causing any
regressions.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some "inline" removing that Andrew suggested, removed some locking on
add/remove at this level - we'll let the callees decide.
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The RedBoot boot loader writes flash partition tables containing native
byte sex 32 bit values. When booting an opposite byte sex kernel (e.g. an
LE kernel from BE RedBoot) the current MTD driver fails to handle the
partition table and therefore is unable to generate the correct partition
map for the flash.
So far as I am aware this problem is ARM specific, because only ARM
supports software change of the CPU (memory system) byte sex, however the
partition table parsing is in generic MTD code. The patch below has been
tested on NSLU2 (an IXP4XX based system) with a patch,
10-ixp4xx-copy-from.patch (submitted to linux-arm-kernel - it's ARM
specific) required to make the maps/ixp4xx.c driver work with an LE kernel.
Builds of the patched system are in the 'unstable' release of OpenSlug and
UcSlugC available from www.nslu2-linux.org. These builds are BE, the
archives at www.nslu2-linux.org and www.handhelds.org (see
monotone.vanille.de) can be built LE (currently DISTRO targets
nslu-ltu.conf for LE thumb uclibc (32 bit kernel) and nslu2-lau.conf,
nslu2-lag.conf for LE arm uclibc/glibc) and this patch has been tested
extensively will both BE and LE systems on the NSLU2 (including swapping
between BE and LE by reflashing from both RedBoot and Linux).
The patch recognises that the FIS directory (the partition table) is
byte-reversed by examining the partition table size, which is known to be
one erase block (this is an assumption made elsewhere in redboot.c). If
the size matches the erase block after byte swapping the value then
byte-reversal is assumed, if not no further action is taken. The patched
code is fail safe; should redboot.c be changed to support a partition table
with a modified size field the test will fail and the partition table will
be assumed to have the host byte sex.
If byte-reversal is detected the patch byte swaps the remainder of the 32
bit fields in the copy of the table; this copy is then used to set up the
MTD partition map.
Signed-off-by: John Bowler <jbowler@acm.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent patch attempted to enable more efficient memory usage by using
only 2kB descriptors for jumbo frames. The method used to implement this
has since been commented upon as "illegal" and in recent kernels even
causes a BUG when receiving ip fragments while using jumbo frames.
This patch simply goes back to the way things were. We expect some
complaints due to order 3 allocations failing to come back due to this
change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Remove Message Signaled Interrupt support (for 2.6.16).
MSI is inherently edge-triggered and that is incompatiable (without more
work) with NAPI.
In future, will replace with smarter lockless-IRQ handling like
tg3.c
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds a bunch of new device IDs to the ftdi_sio driver for
various devices from microHAM using FTDI chips.
Micheal Studer supplied the PID for the USB-Y9 device. I examined the
INF file in microHAM's Windows driver package for the USB-KW, USB-YS,
USB-IC, USB-DB9 and USB-RS232 devices.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the USB vendorID of GSPDA and the productID of GSPDA's palm
smartphone 'xplore m68' to the list of known devices.
Signed-off-by: Hendrik Schweppe <linuxkpatch@hendrik.fam-schweppe.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remote NDIS response to OID_GEN_SUPPORTED_LIST only allocated space
for the data attached to the reply, and not the reply structure
itself. This caused other kmalloc'd memory to be corrupted.
Signed-off-by: Shaun Tancheff <shaun@tancheff.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a dead lock in lh7a40x udc driver. When the driver receive a
SET_FEATURE HALT request, the dev lock is taken by the interrupt
handler lh7a40x_udc_irq then the handler will call lh7a40x_set_halt
function which in its turn will try to acquire the dev lock.
Signed-off-by: Franck Bui-Huu <franck.bui-huu@innova-card.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as656) adds an unusual_devs.h entry for the Lyra RCA RD1080
MP3 player. Its card-reader firmware has the common
report-one-too-many-sectors bug. This fixes Novell bug #152175.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is for the Dual USB Joypad [0925:8866] from Wisegroup. The
HID_QUIRK_NOGET is necessary for it to respond to input, and the
HID_QUIRK_MULTI_INPUT is necessary to have two js# nodes appear.
Signed-off-by: Andrew Fuller <mactalla.obair@gmail.com>
Cc: "Dmitry Torokhov" <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix http://bugzilla.kernel.org/show_bug.cgi?id=6128
Finish morphing the "early handoff" version of the EHCI BIOS handshake over
to match the previous implementation inside the EHCI driver (except that
now we forcibly disable the SMI). The version that had been with the PCI
code was surprisingly full of bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <yazar256@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- change interface of the reset functions from Scsi_Cmnd to Scsi_Host.
- add functions with the original interface and rename the new
functions to reflect the new interface.
- call these from the pcmcia driver, thereby avoiding the need to
construct a (broken) Scsi_Cmnd from a Scsi_Host.
- just run the bh if the interrupt is from the controller and if so
ensure that it's only called once per interrupt.
Signed-off-by: Juergen E. Fischer <fischer@linux-buechse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sym2 boards without NVRAM currently negotiate narrow due to this missed
initialisation
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Stuborn as compilers are they don't like duplicate definitions.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix up an off by one error in calculating retries for scsi
commands. This bug was discovered when an SG_IO request
was sent to scsi core with retries = 0, causing the overall
timeout check to go off in scsi_softirq_done.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch hides the devices completely from the midlayer instead.
It requires the patch to handle the slave_configure failure I posted
earlier.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Current fc_transport consumers initially register rports
with an UNKNOWN role-state and follow-up with a call to
fc_remote_port_rolechg(). Modify code in
fc_remote_port_add() to scan the fc_host_rport_bindings()
array for consistent bindings regardless of role-type.
Original code would only scan bindings array for targets,
causing duplicate fc_remote_ports/rport-X:Y-Z entries to be
created for the yet-to-be-role-changed rports.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove a hack in the sg driver that alters the total buffer
length for SG_IO commands to ensure buffers are not odd byte
lengths. This breaks on the ipr driver since it requires the
request_bufflen to equal the length specified in the cdb.
The block layer SG_IO code does not appear to have this hack.
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adrian> On architectures like i386, the "Multimedia Capabilities Port
Adrian> drivers" menu is visible, but it can't be visited since it
Adrian> contains nothing usable for CONFIG_SGI_SN=n.
Jes> Thats only a third of the patch, if you want to do that, you should
Jes> remove the redundant SGI_SN checks below.
Signed-off-by: Tony Luck <tony.luck@intel.com>
- check that the device is up before it is enabled again;
- the descriptor ring indexes must be set to zero before
cp_init_hw() is issued. Add a nice comment to remember
that skb allocation failure is still not handled.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=5681
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
velocity_rx_refill() only replenishes the descriptor entries which
belong to the CPU. It works great in the Rx path but the driver must
ensure that all the descriptors are freed before velocity_rx_refill()
is used in velocity_change_mtu(). The patch resets the Rx descriptors
in velocity_free_rd_ring().
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Some Sun parts don't have PCI_VENDOR_ID_SUN in the subsystem
vendor ID. So add another fallback test, which is the name
of the OBP firmware device tree node. If it's a Sun part we'll
get "network", else it will be named "ethernet".
Signed-off-by: David S. Miller <davem@davemloft.net>
With the latest kernels, I experienced some strange corruption, some
'*****' being randomly inserted in the character flow, like this:
ashes:~#
ashes:~#
a*******shes:~#
ashes:~#
ashes:~#
Further investigation shows that the problem was introduced during
Alan's "TTY layer buffering revamp" patch, the amount of data to be
copied being reduced after buffer allocation. Moving the count fixup
around solves the problem.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Approved-by: Rogier Wolff <R.E.Wolff@BitWizard.nl>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ACPI is initialized very early on x86-64, before the DMI code is
initialized. This means it would often discover a 0 year and then turn
off ACPI because it thought the BIOS was too old. Some systems don't
boot without ACPI so this was a problem.
I have a full fix by adding new very early DMI detection, but it needs
more testing before it can be merged. For 2.6.16 let's just turn the
check off. It never made much sense anyways because there are no x86-64
systems older than 2002 or so and they generally all have working ACPI.
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes x86-64 use the common X86_PM_TIMER Kconfig entry in drivers/acpi
And since PM timer is needed for correct timing on a lot of systems
now (e.g. AMD dual cores) and we often get bug reports from people
who forgot to set it make it depend on CONFIG_EMBEDDED. x86-64 had
this change before and it's a good thing.
I also fixed the description slightly to make this more clear.
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Matt Mackall