We do not need to have llds set the host no for the session's
parent, because we know the session's parent is going to be
the host. This removes it from the session creation callback
and converts the drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The qdepth setting was useful when we needed libiscsi to verify
the setting. Now we just need to make sure if older tools
passed in zero then we need to set some default.
So this patch just has us use the sht->cmd_per_lun or if
for LLD does a host per session then we can set it on per
host basis.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We were using the shost work queue which ended up being
a little akward since all iscsi hosts need a thread for
scanning, but only drivers hooked into libiscsi need
a workqueue for transmitting. So this patch moves the
xmit workqueue to the lib.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is no need to cap the queue depth in the modules. We set
this in userspace and can do that there. For performance testing
with ram based targets, this is helpful since we can have very
high queue depths.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
iser has its own logging inrfastrucutre. Convert it to use
it instead of libiscsi.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove hard setting of the IB MTU used by iSER's RC queue-pair to 1K,
as this was done due to inter-op issues with an old iser target which
is not used any more.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If path_rec_start() returns error, call path_free() only if the path
was newly-created. If we free an existing path whose valid flag was zero,
(but do not detach it from the list) we cause corruption of the
path list (of which it is a member), and get a kernel crash.
The simplest solution is to not free an existing path -- just leave it
in the list as-is (i.e., with its valid flag cleared).
Thanks to Yossi Etigin of Voltaire for identifying the problem flow
which caused the kernel crash.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Moni Shua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IPoIB tries to join a multicast group, and the SA module's SM
address handle is NULL (because of an SM change, etc), the join
returns with -EAGAIN status. In that case, don't print an error
message unless multicast debugging is enabled.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a deadlock between child interface creation/deletion and ipoib
start/stop. The former takes vlan_mutex, and then might take RTNL via
register_netdev()/unregister_netdev(). The latter is executed with
RTNL held, and tries to take vlan_mutex, which can lead to an AB-BA
deadlock.
Fix this by having the child interface creation/deletion code take the
RTNL first so vlan_mutex always nests inside RTNL. We can use
register_netdevice() for child interfaces because we form the
interface name from the parent interface and hence don't need the '%'
expansion of register_netdev().
Reported-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After commit fe25c561 ("IPoIB: Don't enable NAPI when it's already
enabled"), if an interface is brought up but the corresponding P_Key
never appears, then ipoib_stop() will hang in napi_disable(), because
ipoib_open() returns before it does napi_enable().
Fix this by changing ipoib_open() to call napi_enable() even if the
P_Key isn't present.
Reported-by: Yossi Etigin <yosefe@Voltaire.COM>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/iser: Add dependency on INFINIBAND_ADDR_TRANS
IPoIB: Do not join broadcast group if interface is brought down
RDMA/nes: Fix for NIPQUAD removal
IPoIB: Fix loss of connectivity after bonding failover on both sides
IB/mlx4: Don't register IB device for adapters with no IB ports
mlx4_core: Fix warning from min()
IB/ehca: spin_lock_irqsave() takes an unsigned long
Fix ib_iser build to depend on INFINIBAND_ADDR_TRANS; if INET=y but
IPV6=n, then the RDMA CM is not built but INFINIBAND_ISER can be
enabled, leading to:
ERROR: "rdma_destroy_id" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_connect" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_destroy_qp" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_create_id" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_create_qp" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_resolve_route" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_disconnect" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_resolve_addr" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Because the ipoib_workqueue is not flushed when ipoib interface is
brought down, ipoib_mcast_join() may trigger a join to the broadcast
group after priv->broadcast was set to NULL (during cleanup). This
will cause the system to be a member of the broadcast group when
interface is down. As a side effect, this breaks the optimization of
setting the Q_key only when joining the broadcast group.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix bonding failover in the case both peers failover and the
gratuitous ARP is lost. In that case, the sender side will create an
ipoib_neigh and issue a path request with the old GID first. When
skb->dst->neighbour->ha changes due to ARP refresh, this ipoib_neigh
will not be added to the path->list of the path of the new GID,
because the ipoib_neigh already exists. It will not have an AH
either, because of sender-side failover. Therefore, it will not get
an AH when the path is resolved.
The solution here is to compare GIDs in ipoib_start_xmit() even if
neigh->ah is invalid. Comparing with an uninitialized value of
neigh->dgid should be fine, since a spurious match is harmless (and
astronomically unlikely too).
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We do not need to allocate a itt for data_out, so this
passes the opcode to the alloc_pdu callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This just converts iser to new alloc_pdu api. It still
preallocates the pdu, so there is no difference.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iSCSI/iSER targets may send PDUs without a prior request from the
initiator. RFC 5046 refers to these PDUs as "unexpected". NOP-In PDUs
with itt=RESERVED and Asynchronous Message PDUs occupy this category.
The amount of active "unexpected" PDU's an iSER target may have at any
time is governed by the MaxOutstandingUnexpectedPDUs key, which is not
yet supported.
Currently when an iSER target sends an "unexpected" PDU, the
initiators recv buffer consumed by the PDU is not replaced. If over
initial_post_recv_bufs_num "unexpected" PDUs are received then the
receive queue will run out of receive work requests entirely.
This patch ensures recv buffers consumed by "unexpected" PDUs are
replaced in the next iser_post_receive_control() call.
Signed-off-by: David Disseldorp <ddiss@sgi.com>
Signed-off-by: Ken Sandars <ksandars@sgi.com>
Acked-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a crash in path_rec_completion() during an SM up/down loop. If
more than one path record request is issued, the first completion
releases path->done, allowing ipoib_flush_paths() to free the path,
and thus corrupting it for the second completion.
Commit ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM
change events") added the field path->valid and changed the test "if
(!path)" to "if (!path || !path->valid)". This change made it
possible for a path with an outstanding query to pass the test and
issue another query on the same path. Having two queries on the same
path leads to a crash.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1325>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_flush_paths() can hang during an SM up/down loop: if
path_rec_start() fails (for instance, because there is no sm_ah), the
path is still added to the path list by neigh_add_path(). Then,
ipoib_flush_paths() will wait for path->done, but it will never
complete because the request was not issued at all. Fix this by
completing path->done if issuing the query fails.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1329>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a P_Key is not present when an interface is created, ipoib_open()
will return after doing napi_enable(). ipoib_open() will be called
again from ipoib_pkey_poll() when the P_Key appears, after NAPI has
already been enabled, and try to enable it again. This triggers a
BUG_ON() in napi_enable().
Fix this by moving the call to napi_enable() to after the test for
P_Key presence.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all uses of IPOIB_GID_FMT, IPOIB_GID_RAW_ARG() and IPOIB_GID_ARG()
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Reject dynamic memory add/remove when ehca adapter is present
IB/ehca: Fix reported max number of QPs and CQs in systems with >1 adapter
IPoIB: Set netdev offload features properly for child (VLAN) interfaces
IPoIB: Clean up ethtool support
mlx4_core: Add Ethernet PCI device IDs
mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC
mlx4_core: Multiple port type support
mlx4_core: Ethernet MAC/VLAN management
mlx4_core: Get ethernet MTU and default address from firmware
mlx4_core: Support multiple pre-reserved QP regions
Update NetEffect maintainer emails to Intel emails
RDMA/cxgb3: Remove cmid reference on tid allocation failures
IB/mad: Use krealloc() to resize snoop table
IPoIB: Always initialize poll_timer to avoid crash on unload
IB/ehca: Don't allow creating UC QP with SRQ
mlx4_core: Add QP range reservation support
RDMA/ucma: Test ucma_alloc_multicast() return against NULL, not with IS_ERR()
Child devices were created without any offload features set, fix this by
moving the code that computes the features into generic function which is
now called through non-child and child device creation.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
-- v1 has a bug where the 'result' flag in ipoib_vlan_add may be used uninitialized
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a get_rx_csum method. Remove the driver's own get_tso method, as
the ethtool kernel code uses the default one if nothing is provided.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is a much better version of a previous patch to make the parser
tables constant. Rather than changing the typedef, we put the "const" in
all the various places where its required, allowing the __initconst
exception for nfsroot which was the cause of the previous trouble.
This was posted for review some time ago and I believe its been in -mm
since then.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Cc: Alexander Viro <aviro@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I had this in my patchset to add target reset support, but
it got dropped due to patching conflicts. This initial patch
just renames the function and users. We are actually just
dropping the session, and so this does not have anything to do
with the host exactly. It does for software iscsi because
we allocate a host per session, but for cxgb3i this makes no
sense.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If the driver knows when hardware is removed like with cxgb3i,
bnx2i, qla4xxx and iser then we will want to remove the sessions/devices
that are bound to that device before removing the host.
cxgb3i and in the future bnx2i will remove the host and that will
remove all the sessions on the hba. iser can call iscsi_kill_session
when it gets an event that indicates that a hca is removed.
And when qla4xxx is hooked in to the lib (it is only hooked into
the class right now) it can call iscsi remove host like the
partial offload card drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ipoib_ib_dev_stop() does del_timer_sync(&priv->poll_timer), but if a
P_key for an interface is not found, poll_timer is not initialized, so
this leads to a crash or hang. Fix this by moving where poll_timer is
initialized to ipoib_ib_dev_init(), which is always called.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1172>.
Debugged-by: Yosef Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently, IPoIB is an LLTX driver that uses its own IRQ-disabling
tx_lock. Not only do we want to get rid of LLTX, this actually causes
problems because of the skb_orphan() done with this tx_lock held: some
skb destructors expect to be run with interrupts enabled.
The simplest fix for this is to get rid of the driver-private tx_lock
and stop using LLTX. We kill off priv->tx_lock and use
netif_tx_lock[_bh]() instead; the patch to do this is a tiny bit
tricky because we need to update places that take priv->lock inside
the tx_lock to disable IRQs, rather than relying on tx_lock having
already disabled IRQs.
Also, there are a couple of places where we need to disable BHs to
make sure we have a consistent context to call netif_tx_lock() (since
we no longer can use _irqsave() variants), and we also have to change
ipoib_send_comp_handler() to call drain_tx_cq() through a timer rather
than directly, because ipoib_send_comp_handler() runs in interrupt
context and drain_tx_cq() must run in BH context so it can call
netif_tx_lock().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM
change events") changed how paths are flushed on an SM event. This
change introduces a problem if the path record query triggered by
fails, causing path->ah to become NULL. A later successful path query
will then trigger WARN_ON() in path_rec_completion(), and crash
because path->ah has already been freed, so the ipoib_put_ah() inside
the lock in path_rec_completion() may actually drop the last reference
(contrary to the comment that claims this is safe).
Fix this by updating path->ah and freeing old_ah only when the path
record query is successful. This prevents the neighbour AH and that
path AH from getting out of sync.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1194>
Reported-by: Rabah Salem <ravah@mellanox.com>
Debugged-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Taking rtnl_lock in ipoib_mcast_join_complete() causes a deadlock with
ipoib_stop(). We avoid it by scheduling the piece of code that takes
the lock on ipoib_workqueue instead of executing it directly. This
works because we only flush the ipoib_workqueue with the RTNL not held.
The deadlock happens because ipoib_stop() calls ipoib_ib_dev_down()
which calls ipoib_mcast_dev_flush(), which calls ipoib_mcast_free(),
which calls ipoib_mcast_leave(). The latter calls
ib_sa_free_multicast(), and this waits until the multicast completion
handler finishes. This handler is ipoib_mcast_join_complete(), which
waits for the rtnl_lock(), which was already taken by ipoib_stop().
This bug was introduced in commit a77a57a1 ("IPoIB: Fix deadlock on
RTNL in ipoib_stop()").
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c8c2afe3 ("IPoIB: Use rtnl lock/unlock when changing device
flags") added a call to rtnl_lock() in ipoib_mcast_join_task(), which
is run from the ipoib_workqueue. However, ipoib_stop() (which is run
inside rtnl_lock()) flushes this workqueue, which leads to a deadlock
if the join task is pending.
Fix this by simply not flushing the workqueue from ipoib_stop(). It
turns out that we really don't care about workqueue tasks running
during or after ipoib_stop(), as long as we make sure to flush the
workqueue before unregistering a netdev.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1114>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There are users that are running UDP applications that require a large
receive queue size in order to get good performance. To prevent
allocation failures for rx_rings when using non-SRQ mode and large
recv_queue_size (1K or larger), use vmalloc() instead of kcalloc() to
alocate rx_rings.
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
wr->sg_list should be set to the sge pointer passed in, not
priv->cm.rx_sge.
Reported-by: Hoang-Nam Nguyen <HNGUYEN@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The help text for INFINIBAND_IPOIB_DEBUG refers to "ipoib_debugfs,"
which no longer exists. Correct this to talk about the files under
debugfs that are really created.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Connected mode is now tested and used by lots of people. No need to
hide it under CONFIG_EXPERIMENTAL.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Print the return code of ib_sa_path_rec_get() if it fails to help
debug errors.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enhance iser to act upon notification on network stack changes that
make its RDMA connection unaligned with the link used by the stack for
the <src,dst> IPs used to establish the connection.
When RDMA_CM_EVENT_ADDR_CHANGE arrives, just disconnect the
connection, assuming that the user space iscsid daemon will reconnect,
and the new connection will be aligned with the IP stack.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (102 commits)
[SCSI] scsi_dh: fix kconfig related build errors
[SCSI] sym53c8xx: Fix bogus sym_que_entry re-implementation of container_of
[SCSI] scsi_cmnd.h: remove double inclusion of linux/blkdev.h
[SCSI] make struct scsi_{host,target}_type static
[SCSI] fix locking in host use of blk_plug_device()
[SCSI] zfcp: Cleanup external header file
[SCSI] zfcp: Cleanup code in zfcp_erp.c
[SCSI] zfcp: zfcp_fsf cleanup.
[SCSI] zfcp: consolidate sysfs things into one file.
[SCSI] zfcp: Cleanup of code in zfcp_aux.c
[SCSI] zfcp: Cleanup of code in zfcp_scsi.c
[SCSI] zfcp: Move status accessors from zfcp to SCSI include file.
[SCSI] zfcp: Small QDIO cleanups
[SCSI] zfcp: Adapter reopen for large number of unsolicited status
[SCSI] zfcp: Fix error checking for ELS ADISC requests
[SCSI] zfcp: wait until adapter is finished with ERP during auto-port
[SCSI] ibmvfc: IBM Power Virtual Fibre Channel Adapter Client Driver
[SCSI] sg: Add target reset support
[SCSI] lib: Add support for the T10 (SCSI) Data Integrity Field CRC
[SCSI] sd: Move scsi_disk() accessor function to sd.h
...
Now that we have a specific lock to protect the network
device unicast and multicast lists, remove extraneous
grabs of the TX lock in cases where the code only needs
address list protection.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_addr_{lock,unlock}{,_bh}() helpers.
Use them to protect operations that operate on or read
the network device unicast and multicast address lists.
Also use them in cases where the code simply wants to
block calls into the driver's ->set_rx_mode() and
->set_multicast_list() methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase IPoIB ring sizes to twice their original sizes (RX: 128->256,
TX: 64->128) to act as a shock absorber for high traffic peaks. With
the current settings, we have seen cases that there are many calls to
netif_stop_queue(), which causes degradation in throughput. Also,
larger receive buffer sizes help IPoIB in CM mode to avoid experiencing
RNR NAK conditions due to insufficient receive buffers at the SRQ.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since IPoIB connected mode does not NETIF_F_SG, we only have one DMA
mapping per send, so we don't need a mapping[] array. Define a new
struct with a single u64 mapping member and use it for the CM tx_ring.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the driver sets the MTU of the net device outside of its
change_mtu method, it should make use of dev_set_mtu() instead of
directly setting the mtu field of struct netdevice. Otherwise
functions registered to be called upon MTU change will not get called
(this is done through call_netdevice_notifiers() in dev_set_mtu()).
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use of this lock is required to synchronize changes to the netdvice's
data structs. Also move the call to ipoib_flush_paths() after the
modification of the netdevice flags in set_mode().
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_mcast_detach() does nothing except call ib_detach_mcast(), so just
use the core API in the one place that does a multicast group detach.
add/remove: 0/1 grow/shrink: 0/1 up/down: 0/-105 (-105)
function old new delta
ipoib_mcast_leave 357 319 -38
ipoib_mcast_detach 67 - -67
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current code will set the Q_Key for any join of a non-sendonly
multicast group. The operation involves a modify QP operation, which
is fairly heavyweight, and is only really required after the join of
the broadcast group. Fix this by adding a parameter to ipoib_mcast_attach()
to control when the Q_Key is set.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
No need for a mutex around calls to ib_attach_mcast/ib_detach_mcast
since these operations are synchronized at the HW driver layer.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IPOIB_MCAST_STARTED flag is not used at all since commit b3e2749b
("IPoIB: Don't drop multicast sends when they can be queued"), so
remove it.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The patch tries to solve the problem of device going down and paths being
flushed on an SM change event. The method is to mark the paths as candidates for
refresh (by setting the new valid flag to 0), and wait for an ARP
probe a new path record query.
The solution requires a different and less intrusive handling of SM
change event. For that, the second argument of the flush function
changes its meaning from a boolean flag to a level. In most cases, SM
failover doesn't cause LID change so traffic won't stop. In the rare
cases of LID change, the remote host (the one that hadn't changed its
LID) will lose connectivity until paths are refreshed. This is no
worse than the current state. In fact, preventing the device from
going down saves packets that otherwise would be lost.
Signed-off-by: Moni Levy <monil@voltaire.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add "ipoib_use_lro" module parameter to enable LRO and an
"ipoib_lro_max_aggr" module parameter to set the max number of packets
to be aggregated. Make LRO controllable and LRO statistics accessible
through ethtool.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set IB_QP_CREATE_BLOCK_MULTICAST_LOOPBACK for IPoIB's UD QPs if
supported by the underlying device. This creates an improvement of up
to 39% in bandwidth when sending multicast packets with IPoIB, and an
improvment of 12% in cpu usage.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For devices that don't support SRQs, ipoib_cm_post_receive_nonsrq() is
called from both ipoib_cm_handle_rx_wc() and ipoib_cm_nonsrq_init_rx(),
and these two callers are not synchronized against each other.
However, ipoib_cm_post_receive_nonsrq() always reuses the same receive
work request and scatter list structures, so multiple callers can end
up stepping on each other, which leads to posting garbled work
requests.
Fix this by having the caller pass in the ib_recv_wr and ib_sge
structures to use, and allocating new local structures in
ipoib_cm_nonsrq_init_rx().
Based on a patch by Pradeep Satyanarayana <pradeep@us.ibm.com> and
David Wilder <dwilder@us.ibm.com>, with debugging help from Hoang-Nam
Nguyen <hnguyen@de.ibm.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The connected mode implementation in the IPoIB driver has a large
overhead in the way SKBs are handled in the receive flow. It usually
allocates an SKB with as big as was used in the currently received SKB
and moves unused fragments from the old SKB to the new one. This
involves a loop on all the remaining fragments and incurs overhead on
the CPU. This patch, for small SKBs, allocates an SKB just large
enough to contain the received data and copies to it the data from the
received SKB. The newly allocated SKB is passed to the stack and the
old SKB is reposted.
When running netperf, UDP small messages, without this pach I get:
UDP UNIDIRECTIONAL SEND TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
14.4.3.178 (14.4.3.178) port 0 AF_INET
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
114688 128 10.00 5142034 0 526.31
114688 10.00 1130489 115.71
With this patch I get both send and receive at ~315 mbps.
The reason that send performance actually slows down is as follows:
When using this patch, the overhead of the CPU for handling RX packets
is dramatically reduced. As a result, we do not experience RNR NAK
messages from the receiver which cause the connection to be closed and
reopened again; when the patch is not used, the receiver cannot handle
the packets fast enough so there is less time to post new buffers and
hence the mentioned RNR NACKs. So what happens is that the
application *thinks* it posted a certain number of packets for
transmission but these packets are flushed and do not really get
transmitted. Since the connection gets opened and closed many times,
each time netperf gets the CPU time that otherwise would have been
given to IPoIB to actually transmit the packets. This can be verified
when looking at the port counters -- the output of ifconfig and the
oputput of netperf (this is for the case without the patch):
tx packets
==========
port counter: 1,543,996
ifconfig: 1,581,426
netperf: 5,142,034
rx packets
==========
netperf 1,1304,089
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
The SRP initiator is currently using ib_find_cached_pkey() and
ib_get_cached_gid() in situations where the uncached ib_find_pkey()
and ib_query_gid() functions serve just as well: sleeping is allowed
and performance is not an issue. Since we want to eliminate the
cached operations in the long term, convert SRP to use the uncached
variants.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes two bugs that are related.
1. Old tools did not set can_queue/cmds_max. This patch modifies
libiscsi so that when we add the host we catch this and set it
to the default.
2. iscsi_tcp thought that the scsi command that was passed to
the eh functions needed a iscsi_cmd_task allocated for it. It
only needed a mgmt task, and now it does not matter since it
all comes from the same pool and libiscsi handles this for the
drivers. ib_iser had copied iscsi_tcp's code and set can_queue
to its max - 1 to handle this. So this patch removes the max -1,
and just sets it to the max.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The recv lock was defined so the iscsi layer could block
the recv path from processing IO during recovery. It
turns out iser just set a lock to that pointer which was pointless.
We now disconnect the transport connection before doing recovery
so we do not need the recv lock. For iscsi_tcp we still stop
the recv path incase older tools are being used.
This patch also has iscsi_itt_to_ctask user grab the session lock
and has the caller access the task with the lock or get a ref
to it in case the target is broken and sends a tmf success response
then sends data or a response for the command that was supposed to
be affected bty the tmf.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds two new attrs used for creating initiator ports and
binding sessions to hardware.
The session level initiatorname:
Since bnx2i does a scsi_host per host device, we need to add the
iface initiator port settings on the session, so we can create
multiple initiator ports (each with different inames) per device/scsi_host.
The current iname reflects that qla4xxx can have one iname per hba, and we are
allocating a host per session for software. The iname on the host will
remain so we can export and set the hba level qla4xxx setting.
The ifacename attr:
To bind a session to a some peice of hardware in userspace we maintain
some mappings, but during boot or iscsid restart (iscsid contains the user
space part of the driver) we need to be able to figure out which of those
host mappings abstractions maps to certain sessions. This patch adds
a ifacename attr, which userspace can set to id the host side of the
endpoint across pivot_roots and iscsid restarts.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This hooks iser into the iscsi endpoint code. Previously it handled the
lookup and allocation. This has been made generic so bnx2i and iser can
share it. It also allows us to pass iser the leading conn's ep, so we
know the ib_deivce being used and can set it as the scsi_host's parent.
And that allows scsi-ml to set the dma_mask based on those values.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently we duplicate the list of sessions, because we were using the
test for if a session was on the host list to indicate if the session
was bound or unbound. We can instead use the target_id and fix up
the class so that drivers like bnx2i do not have to manage the target id
space.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This handles the iscsi_cmd_task rename and renames
the iser cmd task to iser task.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Convert ib_iser to support merged tasks.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently to get a ctask from the session cmd array, you have to
know to use the itt modifier. To make this easier on LLDs and
so in the future we can easilly kill the session array and use
the host shared map instead, this patch adds a nice wrapper
to strip the itt into a session->cmds index and return a ctask.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After the stop_conn callback has returned the LLD should not
touch the scsi cmds. iscsi_tcp and libiscsi use the
conn->recv_lock and suspend_rx field to halt recv path
processing, but iser does not have any protection.
This patch modifies iser so that userspace can just
call the ep_disconnect callback, which will halt
all recv IO, before calling the stop_conn callback so
we do not have to worry about the conn->recv_lock and
suspend rx field. iser just needs to stop the send side
from accessing the ib conn.
Fixup to handle when the ep poll fails and ep disconnect
is called from Erez.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This removes the session and conn data_size fields from the iscsi_transport.
Just pass in the value like with host allocation. This patch also makes
it so the LLD iscsi_conn data is allocated with the iscsi_cls_conn.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This finishes the host/session unbinding, by adding some helpers
to add and remove hosts and the session they manage.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bnx2i allocates a host per netdevice but will use libiscsi,
so this unbinds the session from the host in that code.
This will also be useful for the iser parent device dma settings
fixes.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
max_cmd_len and max_conn are not really used. max_cmd_len is
always 16 and can be set by the LLD. max_conn is always one
since we do not support MCS.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
iscsi offload (bnx2i and qla4xx) allocate a scsi host per hba,
so the session creation path needs a shost/host_no argument.
Software iscsi/iser will follow the same behabior as before
where it allcoates a host per session, but in the future iser
will probably look more like bnx2i where the host's parent is
the hardware (rnic for iser and for bnx2i it is the nic), because
it does not use a socket layer like how iscsi_tcp does.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We saw a kernel oops in our regression testing when a multicast "join
finish" occurred just after the interface was -- this is
<https://bugs.openfabrics.org/show_bug.cgi?id=1040>. The test
randomly causes the HCA physical port to go down then up.
The cause of this is that ipoib_mcast_join_finish() processing happen
just after ipoib_mcast_dev_flush() was invoked (in which case the
broadcast pointer is NULL). This patch tests for and handles the case
where priv->broadcast is NULL.
Cc: <stable@kernel.org>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit f56bcd80 ("IPoIB: Use separate CQ for UD send completions")
introduced a bug where the transmit queue could get stopped and never
woken up. The problem is that send completions are only polled at the
end of the xmit function, so if the send queue fills up and the xmit
path stops the queue, then there is no way for send completions to
ever get polled, and so the transmit queue stays stopped forever.
Fix this by arming the send CQ just before posting the last send
request that fills the send queue. Then, when the completion event
handler is called, drain the send CQ. Since it is possible that not
enough send completions are in the CQ, verify that the the net queue
has been woken up after draining the send CQ, and if not arm a timer
and drain again at the timer function.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When creating a child interface, copy the MTU information from the
parent. Otherwise when the child's multicast join completes, the MTU
will not be updated since the code does
dev->mtu = min(priv->mcast_mtu, priv->admin_mtu);
and priv->admin_mtu will be set to 0.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use a dedicated CQ for UD send completions. Also, do not arm the UD
send CQ, which reduces the number of interrupts generated. This patch
farther reduces overhead by not calling poll CQ for every posted send
WR -- it does polls only when there 16 or more outstanding work requests.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Count FMR alignment violations per session as part of the iscsi
statistics.
Signed-off-by: Eli Dorfman <elid@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch enables IPoIB to use 4K UD messages (when the underlying
device and fabrics support a 4K MTU) by using two scatter buffers when
PAGE_SIZE is less than or equal to thhe HCA IB MTU size. The first
buffer is for IPoIB header + GRH header, and the second buffer is the
IPoIB payload, which is 4K-4.
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This sets us up to be able to convert the srp_host to use a struct
device instead of a class_device.
Based on a original patch from Tony Jones, but split up into this piece
by Greg.
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Reviewed-by: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The itt field in struct iscsi_data is not defined with any particular
endianness. open-iscsi should use it as-is without byte-swapping it.
This fixes sparse warnings coming from doing ntohl(hdr->itt).
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a P_Key is deleted and then re-added at the same index, then IPoIB
gets confused because __ipoib_ib_dev_flush() only checks whether the
index is the same without checking whether the P_Key was present, so
the interface is stopped when the P_Key is deleted, but the event when
the P_Key is re-added gets ignored and the interface never gets
restarted.
Also, switch to using ib_find_pkey() instead of ib_find_cached_pkey()
everywhere in IPoIB, since none of the places that look for P_Keys are
in a fast path or in non-sleeping context, and in general we want to
kill off the whole caching infrastructure eventually. This also fixes
consistency problems caused because some IPoIB queries were cached and
some were uncached during the window where the cache was not updated.
Thanks to Venkata Subramonyam <vsubramo@cisco.com> for debugging this
problem and testing this fix.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a RDMA_CM_EVENT_DEVICE_REMOVAL event is raised, iSER should
release the connection resources.
This is necessary when the IB HCA module is unloaded while open-iscsi
is still running. Currently, iSER just BUG()s.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This can be used to tune at run time the parameters controlling the
event (interrupt) generation rate and thus reduce the overhead
incurred by handling interrupts resulting in better throughput. Since
IPoIB uses a single CQ for both RX and TX, RX is chosen to dictate
configuration for both RX and TX.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Just add the infrastructure so we can add functionality later.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For HCAs that support TCP segmentation offload (IB_DEVICE_UD_TSO), set
NETIF_F_TSO and use HW LSO to offload TCP segmentation.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Convert list_splice() + INIT_LIST_HEAD() to the equivalent list_splice_init()
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current SRP initiator will allow unlimited s/g entries in the
indirect descriptors lists, but the entry count field in the SRP_CMD
request is 8 bits, so setting srp_sg_tablesize too large will open the
possibility of wrapping the count and generating invalid requests.
Clamp srp_sg_tablesize to the protocol limits to prevent surprises.
Reported by Martin W. Schlining III <mschlining@datadirectnet.com>.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For HCAs that support checksum offload (ie that set IB_DEVICE_UD_IP_CSUM
in the device capabilities flags), have IPoIB set NETIF_F_IP_CSUM and
use the HCA to generate and verify IP checksums.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 7143740d ("IPoIB: Add send gather support") made struct
ipoib_tx_buf significantly larger, since the mapping member changed
from a single u64 to an array with MAX_SKB_FRAGS + 1 entries. This
means that allocating tx_rings with kzalloc() may fail because there
is not enough contiguous memory for the new, much bigger size. Fix
this regression by allocating the rings with vmalloc() instead.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 7143740d ("IPoIB: Add send gather support") made it possible
for tx_wr.num_sge to be != 1 -- this happens if send gather support is
enabled. However, the code in the connected mode post_send() function
assumes the old invariant, namely that tx_wr.num_sge is always 1. Fix
this by explicitly setting tx_wr.num_sge to 1 in the CM post_send().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When set_multicast_list() is called the multicast task is restarted
and the IPOIB_MCAST_STARTED bit is cleared. As a result for some
window of time, multicast packets are not transmitted nor queued but
rather dropped by ipoib_mcast_send(). These dropped packets are
painful in two cases:
- bonding fail-over which both calls set_multicast_list() on the new
active slave and sends Gratuitous ARP through that slave.
- IP_DROP_MEMBERSHIP code which both calls set_multicast_list() on the
device and issues IGMP leave.
In both these cases, depending on the scheduling of the IPoIB
multicast task, the packets would be dropped. As a result, in the
bonding case, the failover would not be detected by the peers until
their neighbour is renewed the neighbour (which takes a few tens of
seconds). In the IGMP case, the IP router doesn't get an IGMP leave
and would only learn on that from further probes on the group (also a
delay of at least a few tens of seconds).
Fix this by allowing transmission (or queuing) depending on the
IPOIB_FLAG_OPER_UP flag instead of the IPOIB_MCAST_STARTED flag.
Signed-off-by: Olga Shern <olgas@voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
"iser_device" allocation failure is "handled" with a BUG_ON() right
before dereferencing the NULL-pointer - fix this!
Signed-off-by: Arne Redlich <arne.redlich@xiranet.com>
Signed-off-by: Erez Zilber <erezz@voltaire.com>
The iteration through the list of "iser_device"s during device
lookup/creation is broken -- it might result in an infinite loop if
more than one HCA is used with iSER. Fix this by using
list_for_each_entry() instead of the open-coded flawed list iteration
code.
Signed-off-by: Arne Redlich <arne.redlich@xiranet.com>
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit efcd9971 ("IPoIB/cm: Factor out ipoib_cm_free_rx_reap_list()")
introduced a bug in ipoib_cm_dev_stop() when the receive drain times
out. In that case, the function moves all the pending rx stuff into a
private list but then calls ipoib_cm_free_rx_reap_list(), which
handles a different list.
Fix this by moving everything to the rx_reap_list that will actually
get freed up.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=906>.
Signed-off-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
struct ipoib_cm_tx.ibwc is unused since commit 1b524963 ("IPoIB/cm:
Use common CQ for CM send completions"), so remove it.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
In P_Key event handling, if the old P_Key is no longer available, the
driver must call ipoib_ib_dev_stop() -- just as it does when the P_Key
is still available (see procedure __ipoib_ib_dev_flush()).
When a P_Key becomes available, the driver will perform ipoib_open(),
which assumes that the QP is in RESET, the cm_id has been
destroyed/deleted, etc. If ipoib_ib_dev_stop() is not called as
described above, then these assumptions will be false, and the attempt
to bring the interface up will fail.
Found by Mellanox QA.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch acts as a preparation for using checksum offload for IB
devices capable of inserting/verifying checksum in IP packets. The
patch does not actaully turn on NETIF_F_SG - we defer that to the
patches adding checksum offload capabilities.
We only add support for send gathers for datagram mode, since existing
HW does not support checksum offload on connected QPs.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
All current InfiniBand devices can handle all DMA addresses, and it's
hard to imagine anyone would be silly enough to build a new device
that couldn't. Therefore, enable the NETIF_F_HIGHDMA feature for IPoIB.
This has no effect for no, but is needed when we enable gather/scatter
support and checksum stateless offloads.
Signed-off-by: Eli Cohen <eli@mellnaox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a host just goes away (crash, power loss, etc.) without tearing
down its IB connections, it can get stale connection errors when it
tries to reconnect to targets upon rebooting. Retrying the connection
a few times will prevent sysadmins from playing the "which disk(s)
went missing?" game.
This would have made things slightly quicker when tracking down some
of the recent bugs, but it also helps quite a bit when you've got a
large number of targets hanging off a wedged server.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 732a2170 ("IB/ipoib: Bound the net device to the ipoib_neigh
structue") left a misleading debug print (n->dev would be a bond
device only if boding is used). Clean it up.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move up the code that checks for a situation where the remote GID
stored in the ipoib_neigh is different than the one present in the
neighbour (handle gratuitous ARP) or that a bonding fail over has
happened but the neighbour still has a pointer to an ipoib_neigh
created by a different device than the current slave. This will cause
the driver to apply the check also for connected mode neighbours.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With the sg table code, every SCSI driver is now either chain capable
or broken (or has sg_tablesize set so chaining is never activated), so
there's no need to have a check in the host template.
Also tidy up the code by moving the scatterlist size defines into the
SCSI includes and permit the last entry of the scatterlist pools not
to be a power of two.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
qdisc_run() now tests for queue_stopped() before calling
__qdisc_run(), and the same check is done in every iteration of
__qdisc_run(), so another check is not required in the driver xmit.
This means that ipoib_start_xmit() no longer needs to test
netif_queue_stopped(); the test was added to fix earlier kernels,
where the networking stack did not guarantee that the xmit method of
an LLTX driver would not be called after the queue was stopped, but
current kernels do provide this guarantee.
To validate, I put a debug in the TX_BUSY path which never hit with 64
threads running overnight exercising this code a few 100 million
times.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a .change_queue_depth handler to the scsi_host_template in the
iSER driver. iscsi_change_queue_depth was added to iscsi_tcp in order
to solve the problem of queue depth which was too high for some
targets. It is also applicable for iSER.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some RDMA CM events are not supported or not handled in iSER.
This patch adds some info (printk) for the user about them.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When you have multiple targets, it gets really confusing when you try
to track down who did a reset when there is no identifying information
in the log message, especially when the same extension ID is mapped
through two different local IB ports. So, add an identifier that can
be used to track back to which local IB port/remote target pair is the
one having problems.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Acked-by: Pete Wyckoff <pw@osc.edu>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some HCAs (such as ehca2) support SRQ, but only support fewer than 16 SG
entries for SRQs. Currently IPoIB/CM implicitly assumes all HCAs will
support 16 SG entries for SRQs (to handle a 64K MTU with 4K pages). This
patch removes that restriction by limiting the maximum MTU in connected
mode to what the maximum number of SRQ SG entries allows.
This patch addresses <https://bugs.openfabrics.org/show_bug.cgi?id=728>
Signed-off-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
By default, the SCSI mid-layer seems to send down 512KB requests
(sg_tablesize = 256), with some requests occasionally combined. By
allowing the mid-layer to chain requests, we can easily grow to 1024KB
or larger -- I've tested 4096KB I/O requests with no problems.
I looked through the DMA paths on the hardware drivers to ensure they
could take advantage of the SG chaining, and it seems that every one
except ipath uses the system's DMA routines, which have been converted
to handle chaining. ipath looks like it should be OK, but I have no
way to test it.
Signed-off-by: David Dillow <dillowda@ornl.gov>
[ Tested on ipath. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current SRP initiator will send requests even if it has no credits
available. The results of sending extra requests are vendor specific,
but on some devices, overrunning credits will cost 85% of peak
performance -- e.g. 100 MB/s vs 720 MB/s. Other devices may just drop
the requests.
This patch will tell the SCSI midlayer to queue requests if there are
fewer than two credits remaining, and will not issue a task management
request if there are no credits remaining. The mid-layer will retry
the queued command once an outstanding command completes.
The patch also removes the unlikely() in __srp_get_tx_iu(), as it is
not at all unlikely to hit this limit under heavy load.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
An IPoIB subnet on an IB fabric that spans multiple IB subnets can't
use link-local scope in multicast GIDs. The existing routines that
map IP/IPv6 multicast addresses into IB link-level addresses hard-code
the scope to link-local, and they also leave the partition key field
uninitialised. This patch adds a parameter (the link-level broadcast
address) to the mapping routines, allowing them to initialise both the
scope and the P_Key appropriately, and fixes up the call sites.
The next step will be to add a way to configure the scope for an IPoIB
interface.
Signed-off-by: Rolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some IB adapters (notably IBM's eHCA) do not implement SRQs (shared
receive queues). The current IPoIB connected mode support only works
on devices that support SRQs.
Fix this by adding support for using the receive queue of each
connected mode receive QP. The disadvantage of this compared to using
an SRQ is that it means a full queue of receives must be posted for
each remote connected mode peer, which means that total memory usage
is potentially much higher than when using SRQs. To manage this, add
a new module parameter "max_nonsrq_conn_qp" that limits the number of
connections allowed per interface.
The rest of the changes are fairly straightforward: we use a table of
struct ipoib_cm_rx to hold all the active connections, and put the
table index of the connection in the high bits of receive WR IDs.
This is needed because we cannot rely on the struct ib_wc.qp field for
non-SRQ receive completions. Most of the rest of the changes just
test whether or not an SRQ is available, and post receives or find
received packets in the right place depending on the answer.
Cleaning up dead connections actually becomes simpler, because we do
not have to do the "last WQE reached" dance that is required to
destroy QPs attached to an SRQ. We just move the QP to the error
state and wait for all pending receives to be flushed.
Signed-off-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
[ Completely rewritten and split up, based on Pradeep's work. Several
bugs fixed and no doubt several bugs introduced. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor out the code for going through the rx_reap list of struct
ipoib_cm_rx and freeing each one. This consolidates the code
duplicated between ipoib_cm_dev_stop() and ipoib_cm_rx_reap() and
reduces the risk of error when adding additional accounting.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor out the code to create an SRQ and allocate the receive ring in
ipoib_cm_dev_init() into a new function ipoib_cm_create_srq(). This
will make the code neater when support for devices that don't implement
SRQs is added.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor out the code to unmap/free skbs and free the receive ring in
ipoib_cm_dev_cleanup() into a new function ipoib_cm_free_rx_ring().
This function will be called from a couple of other places when
support for devices that don't implement SRQs is added.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
eh_device_reset_handler was already added to scsi_host_template
in iscsi_tcp, and is now added also for iscsi_iser.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Convert xmit to iscsi chunks.
from michaelc@cs.wisc.edu:
Bug fixes, more digest integration, sg chaining conversion and other
sg wrapper changes, coding style sync up, and removal of io fields,
like pdu_sent, that are not needed.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
During root boot and shutdown the target could send us nops.
At this time iscsid cannot be running, so the target will drop
the session and the boot or shutdown will hang.
To handle this and allow us to better control when to check the network
this patch moves the nop handling to the kernel.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is not need to block the session during logout. Since
we are going to fail the commands that were blocked just fail them
immediately instead.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- The default initialization of hdr_max is the minimum -
sizeof(struct iscsi_cmd) - Once this patch goes into iser the default
initialization at libiscsi can be removed.
- This is not yet full support for AHSs at iser end. But it should be easy.
Just allocate more space at iser_desc right after iscsi_hdr. Than
at transmission time use ctask->hdr_len to retrieve the total
size of all iscsi pdu headers. See previous patch at iscsi_tcp.[ch]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds logical unit reset support. This should work for ib_iser,
but I have not finished testing that driver so it is not hooked in yet.
This patch also temporarily reverts the iscsi_tcp r2t write out patch.
That code is completely rewritten in this patchset.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The documented call sequence for removing a host is to call the
transport xxx_remove_host() prior to scsi_remove_host(). The SRP
transport used to crash when that order was followed, but as it is now
fixed, use the documented order.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a missing call to srp_remove_host() in srp_remove_one() so that we
don't leak SRP transport class list entries.
Tested-by: David Dillow <dillowda@ornl.gov>
Acked-by: FUJITA Tomonori <tomof@acm.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a port goes down, ipoib_ib_dev_down() is invoked -- which flushes
the mcasts (clearing priv->broadcast) and clearing the path record
cache. If ipoib_start_xmit() is then invoked (before the broadcast
group is rejoined), a kernel oops results from attempting to access
priv->broadcast, which is still unset.
Returning NULL from path_rec_create() if priv->broadcast is NULL is a
harmless way of bypassing the problem -- the offending packet is
simply discarded "without prejudice."
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
While adding sg chaining support to iSER, a "for" loop was replaced
with a "for_each_sg" loop. The "for" loop included the incrementation
of 2 variables. Only one of them is incremented in the current
"for_each_sg" loop. This caused iSER to think that all data is
unaligned, and all data was copied to aligned buffers.
This patch increments the missing counter inside the "for_each_sg"
loop whenever necessary.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 1b524963 ("IPoIB/cm: Use common CQ for CM send completions")
changed how the high-order bits of work request IDs were used, which
had the effect that IPOIB_CM_RX_DRAIN_WRID was no longer handled as a
connected mode receive completion. This leads to the messages
ib1: cm send completion event with wrid 1073741823 (> 64)
ib1: RX drain timing out
when an interface with connected mode QPs is brought down. Fix this
by making sure that both IPOIB_OP_CM and IPOIB_OP_RECV are set in
IPOIB_CM_RX_DRAIN_WRID.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Increase command timeout for INIT_HCA to 10 seconds
IPoIB/cm: Use common CQ for CM send completions
IB/uverbs: Fix checking of userspace object ownership
IB/mlx4: Sanity check userspace send queue sizes
IPoIB: Rewrite "if (!likely(...))" as "if (unlikely(!(...)))"
IB/ehca: Enable large page MRs by default
IB/ehca: Change meaning of hca_cap_mr_pgsize
IB/ehca: Fix ehca_encode_hwpage_size() and alloc_fmr()
IB/ehca: Fix masking error in {,re}reg_phys_mr()
IB/ehca: Supply QP token for SRQ base QPs
IPoIB: Use round_jiffies() for ah_reap_task
RDMA/cma: Fix deadlock destroying listen requests
RDMA/cma: Add locking around QP accesses
IB/mthca: Avoid alignment traps when writing doorbells
mlx4_core: Kill mlx4_write64_raw()
Use the same CQ for CM send completions as for all other IPoIB
completions. This means all completions are processed via the same
NAPI polling routine. This should help reduce the number of
interrupts for bi-directional traffic (such as TCP) and fixes "driver
is hogging interrupts" errors reported for IPoIB send side, e.g.
<https://bugs.openfabrics.org/show_bug.cgi?id=508>
To do this, keep a per-interface counter of outstanding send WRs, and
stop the interface when this counter reaches the send queue size to
avoid CQ overruns.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
It's too hard to figure out what "!likely(...)" really means, and who
knows how compilers interpret the hint.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use round_jiffies() to align the 1 second ah_reap_task with other work
and potentially save power by sleeping cores for longer.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the bonding device senses a carrier loss of its active slave it replaces
that slave with a new one. In between the times when the carrier of an IPoIB
device goes down and ipoib_neigh is destroyed, it is possible that the
bonding driver will send a packet on a new slave that uses an old ipoib_neigh.
This patch detects and prevents this from happenning.
Signed-off-by: Moni Shoua <monis at voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com>
Acked-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
IPoIB uses a two layer neighboring scheme, such that for each struct neighbour
whose device is an ipoib one, there is a struct ipoib_neigh buddy which is
created on demand at the tx flow by an ipoib_neigh_alloc(skb->dst->neighbour)
call.
When using the bonding driver, neighbours are created by the net stack on behalf
of the bonding (master) device. On the tx flow the bonding code gets an skb such
that skb->dev points to the master device, it changes this skb to point on the
slave device and calls the slave hard_start_xmit function.
Under this scheme, ipoib_neigh_destructor assumption that for each struct
neighbour it gets, n->dev is an ipoib device and hence netdev_priv(n->dev)
can be casted to struct ipoib_dev_priv is buggy.
To fix it, this patch adds a dev field to struct ipoib_neigh which is used
instead of the struct neighbour dev one, when n->dev->flags has the
IFF_MASTER bit set.
Signed-off-by: Moni Shoua <monis at voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com>
Acked-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This adds a 'roles' attribute to rport like transport_fc. The role can
be initiator or target. That is, the initiator driver creates target
remote ports and the target driver creates initiator remote ports.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This converts ib_srp to use the srp transport class.
I don't have ib hardware so I've not tested this patch.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (87 commits)
mlx4_core: Fix section mismatches
IPoIB: Allow setting policy to ignore multicast groups
IB/mthca: Mark error paths as unlikely() in post_srq_recv functions
IB/ipath: Minor fix to ordering of freeing and zeroing of tid pages.
IB/ipath: Remove redundant link state checks
IB/ipath: Fix IB_EVENT_PORT_ERR event
IB/ipath: Better handling of unexpected GPIO interrupts
IB/ipath: Maintain active time on all chips
IB/ipath: Fix QHT7040 serial number check
IB/ipath: Indicate a couple of chip bugs to userspace
IB/ipath: iba6110 rev4 no longer needs recv header overrun workaround
IB/ipath: Use counters in ipath_poll and cleanup interrupts in ipath_close
IB/ipath: Remove duplicate copy of LMC
IB/ipath: Add ability to set the LMC via the sysfs debugging interface
IB/ipath: Optimize completion queue entry insertion and polling
IB/ipath: Implement IB_EVENT_QP_LAST_WQE_REACHED
IB/ipath: Generate flush CQE when QP is in error state
IB/ipath: Remove redundant code
IB/ipath: Future proof eeprom checksum code (contents reading)
IB/ipath: UC RDMA WRITE with IMMEDIATE doesn't send the immediate
...
The conversion to use netdevice internal stats left an unused variable
in ipoib_neigh_free(), since there's no longer any reason to get
netdev_priv() in order to increment dropped packets. Delete the
unused priv variable.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the stats member of struct netdevice in IPoIB, so we can save
memory by deleting the stats member of struct ipoib_dev_priv, and save
code by deleting ipoib_get_stats().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hardware header operations are part of the protocol class
not the device instance, make them into a separate object and
save memory.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.
In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.
The signature of the ->poll() call back goes from:
int foo_poll(struct net_device *dev, int *budget)
to
int foo_poll(struct napi_struct *napi, int budget)
The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract). The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.
The napi_struct is to be embedded in the device driver private data
structures.
Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler. Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.
With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.
Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.
[ Ported to current tree and all drivers converted. Integrated
Stephen's follow-on kerneldoc additions, and restored poll_list
handling to the old style to fix mutual exclusion issues. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel IB stack allows (through the RDMA CM) userspace
applications to join and use multicast groups from the IPoIB MGID
range. This allows multicast traffic to be handled directly from
userspace QPs, without going through the kernel stack, which gives
better performance for some applications.
However, to fully interoperate with IP multicast, such userspace
applications need to participate in IGMP reports and queries, or else
routers may not forward the multicast traffic to the system where the
application is running. The simplest way to do this is to share the
kernel IGMP implementation by using the IP_ADD_MEMBERSHIP option to
join multicast groups that are being handled directly in userspace.
However, in such cases, the actual multicast traffic should not also
be handled by the IPoIB interface, because that would burn resources
handling multicast packets that will just be discarded in the kernel.
To handle this, this patch adds lookup on the database used for IB
multicast group reference counting when IPoIB is joining multicast
groups, and if a multicast group is already handled by user space,
then the IPoIB kernel driver ignores the group. This is controlled by
a per-interface policy flag. When the flag is set, IPoIB will not
join and attach its QP to a multicast group which already has an entry
in the database; when the flag is cleared, IPoIB will behave as before
this change.
For each IPoIB interface, the /sys/class/net/$intf/umcast attribute
controls the policy flag. The default value is off/0.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make the way QP is being created in ipoib_cm_create_tx_qp()
consistent with ipoib_cm_create_rx_qp().
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
<asm/scatterlist.h> is not needed because everyplace it appears,
<linux/scatterlist.h> also appears. <asm/io.h> is not needed because
nothing seems to be using device IO anyway.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Provide the target service ID when performing a path record query to
support optional QoS capability. QoS requires support from the SA.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clean up properly if ib_query_pkey() or ib_query_gid() fail.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current IPoIB code might process receive completions from
ipoib_drain_cq() when bringing down the interface. This could cause
packets to be passed up the stack without the device's poll method
being called. Avoid this by setting the status of any successful
completions to IB_WC_WR_FLUSH_ERR.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_transport_dev_init() calls ipoib_cm_dev_init(), so it needs to
call ipoib_cm_dev_cleanup() to unwind that on the error path.
Found by Dotan Barak of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
New Cisco IB SRP targets use the Cisco OUI 00-1b-0d but still need the
Topspin workarounds. Add this OUI to srp_target_is_topspin().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Wrap the checking for Mellanox and Topspin OUIs to decide whether to
use a workaround into helper functions. This will make it cleaner to
add a new OUI to check (as we need to do now that some targets with a
Cisco OUI still need the Topspin workarounds).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This prevents the iscsi modules from being unloaded while
there are active mounts from an iscsi target.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make iser_conn_release() and iser_start_rdma_unaligned_sg() static,
since they are only used in the .c file where they are defined. In
addition to being a cleanup, this even shrinks the generated code by
allowing the single call of iser_start_rdma_unaligned_sg() to be
inlined into its callsite. On x86_64:
add/remove: 0/1 grow/shrink: 1/0 up/down: 466/-533 (-67)
function old new delta
iser_reg_rdma_mem 1518 1984 +466
iser_start_rdma_unaligned_sg 533 - -533
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
The IB CM should include the HCA ACK delay when calculating the local
ACK timeout value to use for RC QPs. If the HCA ACK delay is large
enough relative to the packet life time, then if it is not taken into
account, the calculated timeout value ends up being too small, which
can result in "retry exceeded" errors.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
InfiniBand HCAs replicate multicast packets back to the QP that sent
them if that QP is attached to the destination multicast group. This
means that IPoIB multicasts are often replicated back to the receive
queue of the interface that generated them. To avoid confusing the
network stack, we drop these duplicates within the IPoIB driver.
However, there's no reason to free the skb that received the duplicate
and then immediately allocate a new skb to post to the receive queue.
We can be more efficient and just repost the same skb.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix
drivers/infiniband/ulp/ipoib/ipoib_cm.c:1151: warning: unused variable 'dev'
by getting rid of the variable dev, which is only used if CONFIG_IPV6
is enabled, and replacing the one use of it with the value it is
assigned, namely priv->dev.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a page can't be allocated for the frag list of a skb, the code to
unmap the partially allocated list is off by one. For exaple, if
'frags' equals one, i == 0, and the alloc_page() fails, then the old
loop would have unmapped mapping[1] which is uninitialized. The same
would happen if the call to ib_dma_map_page() failed.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Acked-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IPoIB connected mode currently rejects a connection request unless the
supported MTU is >= the local netdevice MTU. This breaks
interoperability with implementations that might have tweaked
IPOIB_CM_MTU, and there's real no longer a reason to do so: this test
is just a leftover from when we did not tweak MTU per-connection. Fix
this by making the test as permissive as possible.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a crasher bug in IPoIB CM: once a QP is in the RTR state, a
receive completion (or even an asynchronous error) might be observed
on this QP, so we have to initialize all of our receive data
structures before moving to the RTR state.
As an optimization (since modify_qp might take a long time), the
jiffies update done when moving RX to the passive_ids list is also
left in place to reduce the chance of the RX being misdetected as
stale.
This fixes bug <https://bugs.openfabrics.org/show_bug.cgi?id=662>.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
iscsi_iser: convert to use the data buffer accessors
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
TODO: use scsi_for_each_sg().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Jens Axboe <jens.axboe@oracle.com> did the for_each_sg cleanup.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
iSCSI must support software iscsi (iscsi_tcp, iser), hardware iscsi (qla4xxx),
and partial offload (broadcom). To be able to allow each stack or driver
or port (virtual or physical) to be able to log into the same target portal
we use the initiator tuple [[HWADDRESS | NETDEVNAME], INITIATOR_NAME] and
the target tuple [TARGETNAME, CONN_ADDRESS, CONN_PORT] to id a session.
This patch adds the netdev name, which is used by software iscsi when
it binds a session to a netdevice using the SO_BINDTODEVICE sock opt.
It cannot use HWADDRESS because if someone did vlans then the same netdevice
will have the same mac and the initiator,target id will not be unique.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch allows us to set can_queue and cmds_per_lun from userspace
when we create the session/host. From there we can set it on a per
target basis. The patch fully converts iscsi_tcp, but only hooks
up ib_iser for cmd_per_lun since it currently has a lots of preallocations
based on can_queue.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The cmdsn allocation and pdu transmit code can race, and we can end
up sending a pdu with cmdsn 10 before a pdu with 5. The target will
then fail the connection/session. This patch fixes the problem by
delaying the cmdsn allocation until we are about to send the pdu.
This also removes the xmitmutex. We were using the connection xmitmutex
during error handling to handle races with mtask and ctask cleanup and
completion. For ctasks we now have nice refcounting and for the mtask,
if we hit the case where the mtask timesout and it is floating
around somewhere in the driver, we end up dropping the session.
And to handle session level cleanup, we use the xmit suspend bit
along with scsi_flush_queue and the session lock to make sure
that the xmit thread is not possibly transmitting a task while
we are trying to kill it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The attached patches add sysfs files for the chap settings
to the iscsi transport class, iscsi_tcp and ib_iser. This is
needed for software iscsi because there are times when iscsid
can die and it will need to reread the values it was using.
And it is needed by qla4xxx for basic management opertaions.
This patch does not hook in qla4xxx yet, because I am not sure
the mbx command to use.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Remove shadow of request length from struct iscsi_cmd_task.
- change all users to use scsi_cmnd->request_bufflen directly
(With bidi we will use scsi-ml API to retrieve in/out length)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For iscsi root boot, software iscsi needs to know what the BIOS/OF
initiator used for the initiator name so this puts it in sysfs
for userspace to be able to pick up.
For hw iscsi, it is nice to see what the card is using.
This patch adds the new param, and hooks in qla4xxx, iscsi_tcp, and ib_iser.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
iscsid and udev need to key off the hw address being
used so add some helpers for iser and iscsi tcp.
Also convert them
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
commit 518b1646 ("IPoIB/cm: Fix SRQ WR leak") introduced a severe
performance regression on Mellanox cards, because keeping a QP in the
error state for extended periods of time moves hardware to the slow
path (until the QP is destroyed). For example, MPI latency goes from
~3 usecs to ~7 usecs.
Fix this by posting a send WR on one of the QPs that are being
flushed, instead of using a separate drain QP that is kept in the
error state.
This fixes bug <https://bugs.openfabrics.org/show_bug.cgi?id=636>,
reported and bisected by Scott Weitzenkamp at Cisco and debugged by
Sasha Mikheev at Voltaire.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since NAPI polling is disabled while ipoib_cm_dev_stop() is running,
ipoib_cm_dev_stop() must poll the CQ itself in order to see the
packets draining.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
time_after() was used backwards, so the timeout occurred immediately.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SRQ WR leakage has been observed with IPoIB/CM: e.g. flipping ports on
and off will, with time, leak out all WRs and then all connections
will start getting RNR NAKs. Fix this in the way suggested by spec:
move the QP being destroyed to the error state, wait for "Last WQE
Reached" event and then post WR on a "drain QP" connected to the same
CQ. Once we observe a completion on the drain QP, it's safe to call
ib_destroy_qp.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SM reconfiguration or failover possibly causes a shuffling of the values
in the P_Key table. Right now, IPoIB only queries for the P_Key index
once when it creates the device QP, and hence there are problems if the
index of a P_Key value changes. Fix this by using the PKEY_CHANGE event
to trigger a recheck of the P_Key index.
Signed-off-by: Yosef Etigin <yosefe@voltaire.com>
Acked-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In the presence of some running RX connections, we repeat
queue_delayed_work calls each 4 RX WRs, which is a waste. It's enough
to start stale task when a first passive connection is added, and
rerun it every IPOIB_CM_RX_DELAY as long as there are outstanding
passive connections.
This removes some code from RX data path.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Convert to NAPI
IB: Return "maybe missed event" hint from ib_req_notify_cq()
IB: Add CQ comp_vector support
IB/ipath: Fix a race condition when generating ACKs
IB/ipath: Fix two more spin lock problems
IB/fmr_pool: Add prefix to all printks
IB/srp: Set proc_name
IB/srp: Add orig_dgid sysfs attribute to scsi_host
IPoIB/cm: Don't crash if remote side uses one QP for both directions
RDMA/cxgb3: Support for new abort logic
RDMA/cxgb3: Initialize cpu_idx field in cpl_close_listserv_req message
RDMA/cxgb3: Fail qp creation if the requested max_inline is too large
RDMA/cxgb3: Fix TERM codes
IPoIB/cm: Fix error handling in ipoib_cm_dev_open()
IB/ipath: Don't corrupt pending mmap list when unmapped objects are freed
IB/mthca: Work around kernel QP starvation
IB/ipath: Don't put QP in timeout queue if waiting to send
IB/ipath: Don't call spin_lock_irq() from interrupt context
Convert the IP-over-InfiniBand network device driver over to using
NAPI to handle completions for the main CQ. This covers all receives
as well as datagram mode sends; send completions for connected mode
connections are still handled from interrupt context.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a num_comp_vectors member to struct ib_device and extend
ib_create_cq() to pass in a comp_vector parameter -- this parallels
the userspace libibverbs API. Update all hardware drivers to set
num_comp_vectors to 1 and have all ULPs pass 0 for the comp_vector
value. Pass the value of num_comp_vectors to userspace rather than
hard-coding a value of 1.
We want multiple CQ event vector support (via MSI-X or similar for
adapters that can generate multiple interrupts), but it's not clear
how many vectors we want, or how we want to deal with policy issues
such as how to decide which vector to use or how to set up interrupt
affinity. This patch is useful for experimenting, since no core
changes will be necessary when updating a driver to support multiple
vectors, and we know that we want to make at least these changes
anyway.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add an orig_dgid attribute in sysfs for SRP scsi_hosts, so that
userspace can tell what the original dgid value written to the
add_target file was, even if the connection is redirected to a
different port while connecting.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IPoIB CM spec allows the use of a single connection in both
active->passive and passive->active directions. The current Linux
code uses one connection for both directions, but if another node only
uses one connection for both directions, we oops when we try to look
up the passive connection. Fix by checking that qp_context is
non-NULL before dereferencing it.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If skb allocation fails when we start the device, we call
ipoib_cm_dev_stop() even though ipoib_cm_dev_open() did not run to
completion, so we pass an invalid pointer to ib_destroy_cm_id and get
an oops.
Fix by clearing cm.id on error, and testing it in cm_dev_stop().
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=561>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband: (49 commits)
IB: Set class_dev->dev in core for nice device symlink
IB/ehca: Implement modify_port
IB/umad: Clarify documentation of transaction ID
IPoIB/cm: spin_lock_irqsave() -> spin_lock_irq() replacements
IB/mad: Change SMI to use enums rather than magic return codes
IB/umad: Implement GRH handling for sent/received MADs
IB/ipoib: Use ib_init_ah_from_path to initialize ah_attr
IB/sa: Set src_path_bits correctly in ib_init_ah_from_path()
IB/ucm: Simplify ib_ucm_event()
RDMA/ucma: Simplify ucma_get_event()
IB/mthca: Simplify CQ cleaning in mthca_free_qp()
IB/mthca: Fix mthca_write_mtt() on HCAs with hidden memory
IB/mthca: Update HCA firmware revisions
IB/ipath: Fix WC format drift between user and kernel space
IB/ipath: Check that a UD work request's address handle is valid
IB/ipath: Remove duplicate stuff from ipath_verbs.h
IB/ipath: Check reserved memory keys
IB/ipath: Fix unit selection when all CPU affinity bits set
IB/ipath: Don't allow QPs 0 and 1 to be opened multiple times
IB/ipath: Disable IB link earlier in shutdown sequence
...
For the common, open coded 'skb->mac.raw = skb->data' operation, so that we can
later turn skb->mac.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are quite a few places in ipoib_cm.c where we know IRQs are
enabled because we do something that sleeps in the same function, so
we can convert several occurrences of spin_lock_irqsave() to a plain
spin_lock_irq(). This cleans up the source a little and makes the
code smaller too:
add/remove: 0/0 grow/shrink: 1/5 up/down: 3/-51 (-48)
function old new delta
ipoib_cm_tx_reap 403 406 +3
ipoib_cm_stale_task 146 145 -1
ipoib_cm_dev_stop 173 172 -1
ipoib_cm_tx_handler 964 956 -8
ipoib_cm_rx_handler 956 937 -19
ipoib_cm_skb_reap 212 190 -22
Signed-off-by: Roland Dreier <rolandd@cisco.com>
To support destinations that are not on the local IB subnet, IPoIB
should include the GRH information when constructing an address
handle. Using the existing ib_init_ah_from_path() call will do this
for us.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
There's no point in printing the opcode field in the completion
handling debugging output, since the type of completion is already
printed at the beginning of the line. In fact the opcode field is not
even defined for completions with a status other than success.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Receive buffers need to be mapped with DMA_FROM_DEVICE. Incorrectly
mapping with DMA_TO_DEVICE causes a hard lock on ppc64 machines with
an IOMMU.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=431>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a connection is terminated asynchronously from the iSCSI layer's
perspective, iSER needs to notify the iSCSI layer that the connection
has failed. This is done using a workqueue (switched to from the iSER
tasklet context). Meanwhile, the connection object (that holds the
work struct) is released. If the workqueue function wasn't called
yet, it will be called later with a NULL pointer, which will crash the
kernel.
The context switch (tasklet to workqueue) is not required, and
everything can be done from the iSER tasklet. This eliminates the NULL
work struct bug (and simplifies the code).
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/iser: Handle aborting a command after it is sent
IB/mthca: Fix thinko in init_mr_table()
RDMA/cxgb3: Fix resource leak in cxio_hal_init_ctrl_qp()
The SCSI midlayer may abort a command that was already sent. If the
initiator is still trying to send the command (or data-out PDUs for
that command), the QP may time out after the midlayer times
out. Therefore, when aborting the command, iSER may still have
references for the command's buffers. When sending these PDUs, the
sends will complete with an error and their resources will be released
then.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
->neigh_destructor() is killed (not used), replaced with
->neigh_cleanup(), which is called when neighbor entry goes to dead
state. At this point everything is still valid: neigh->dev,
neigh->parms etc.
The device should guarantee that dead neighbor entries (neigh->dead !=
0) do not get private part initialized, otherwise nobody will cleanup
it.
I think this is enough for ipoib which is the only user of this thing.
Initialization private part of neighbor entries happens in ipib
start_xmit routine, which is not reached when device is down. But it
would be better to add explicit test for neigh->dead in any case.
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet length checks in ipoib are broken: we add 4 bytes (IPoIB
encapsulation header) when sending a packet, not 20 bytes (hardware
address length) to each packet. Therefore, if connected mode is
enabled so that the interface MTU is larger than the multicast MTU,
IPoIB may end up trying to send too-long multicast packets. For
example, multicast is broken if a message of size 2048 bytes is sent
on an interface with UD MTU 2048, because 2048 is bigger than the real
limit of 2044 but the code tests against the wrong limit of 2060.
This patch fixes <https://bugs.openfabrics.org/show_bug.cgi?id=418>,
submitted by Scott Weitzenkamp <sweitzen@cisco.com>.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The connected mode code added the possibility that an neigh struct
gets freed in the list_for_each_entry() loop in path_rec_completion(),
which causes a use-after-free. Fix this by changing to the _safe
variant of the list walking macro.
This was spotted by the Coverity checker (CID 1567).
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There's a race between ipoib_mcast_leave() and ipoib_mcast_join_finish()
where we can try to detach from a multicast group before we've
attached to it. Fix this by reordering the code in ipoib_mcast_leave
to free the multicast group first, which waits for the multicast
callback thread (which calls ipoib_mcast_join_finish()) to complete
before detaching from the group.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The sense of the time_after_eq() test in ipoib_cm_stale_task() is
reversed so that only non-stale connections are reaped. Fix this by
changing to time_before_eq().
Noticed by Pradeep Satyanarayana <pradeep@us.ibm.com>.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch renames DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH to avoid
confusion with the drivers default values (DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH
is the iscsi RFC specific default).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Do netif_carrier_on() right after the IPv4 broadcast multicast group
is joined, rather than waiting for all of the initial set of multicast
group joins to finish. This allows at least IPv4 traffic to limp
along on broken fabrics where not all multicast groups can be joined.
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
An asynchronous event carries the port number that the event occurred
on, so there's no reason for an IPoIB interface to process an event
associated with a different local HCA port.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If path_rec_completion() is passed a non-NULL path record pointer
along with an unsuccessful status value, the tracing code incorrectly
prints the (invalid) DLID from the path record rather than the more
interesting status code. The actual logic of the function correctly
uses the path record only if the status indicates a successful lookup.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Now that low-level drivers handle the conversion from an absolute rate
to a relative rate, there's no need for the IPoIB driver to keep track
of the local port's data rate.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Avoid the overhead of freeing/reallocating and mapping/unmapping for
DMA pages that have not been written to by hardware.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IB SA tracks multicast join/leave requests on a per port basis and
does not do any reference counting: if two users of the same port join
the same group, and one leaves that group, then the SA will remove the
port from the group even though there is one user who wants to stay a
member left. Therefore, in order to support multiple users of the
same multicast group from the same port, we need to perform reference
counting locally.
To do this, add an multicast submodule to ib_sa to perform reference
counting of multicast join/leave operations. Modify ib_ipoib (the
only in-kernel user of multicast) to use the new interface.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_cm_alloc_rx_skb() might be called from IRQ context, so it must
use dev_kfree_skb_any(), not kfree_skb().
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/mthca: Always fill MTTs from CPU
IB/mthca: Merge MR and FMR space on 64-bit systems
IB/mthca: Fix access to MTT and MPT tables on non-cache-coherent CPUs
IB/mthca: Give reserved MTTs a separate cache line
IB/mthca: Fix reserved MTTs calculation on mem-free HCAs
RDMA/cxgb3: Add driver for Chelsio T3 RNIC
IB: Remove redundant "_wq" from workqueue names
RDMA/cma: Increment port number after close to avoid re-use
IB/ehca: Fix memleak on module unloading
IB/mthca: Work around gcc bug on sparc64
IPoIB: Connected mode experimental support
IB/core: Use ARRAY_SIZE macro for mandatory_table
IB/mthca: Use correct structure size in call to memset()
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following patch adds experimental support for IPoIB connected
mode, as defined by the draft from the IETF ipoib working group. The
idea is to increase performance by increasing the MTU from the maximum
of 2K (theoretically 4K) supported by IPoIB on top of UD. With this
code, I'm able to get 800MByte/sec or more with netperf without
options on a Mellanox 4x back-to-back DDR system.
Some notes on code:
1. SRQ is used for scalability to large cluster sizes
2. Only RC connections are used (UC does not support SRQ now)
3. Retry count is set to 0 since spec draft warns against retries
4. Each connection is used for data transfers in only 1 direction, so
each connection is either active(TX) or passive (RX). 2 sides that
want to communicate create 2 connections.
5. Each active (TX) connection has a separate CQ for send completions -
this keeps the code simple without CQ resize and other tricks
6. To detect stale passive side connections (where the remote side is
down), we keep an LRU list of passive connections (updated once per
second per connection) and destroy a connection after it has been
unused for several seconds. The LRU rule makes it possible to avoid
scanning connections that have recently been active.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This lets the network core have the ability to handle suspend/resume
issues, if it wants to.
Thanks to Frederik Deweerdt <frederik.deweerdt@gmail.com> for the arm
driver fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When there is a call to send_tsk_mgmt SRP posts a send and waits for 5
seconds to get a response.
When the QP is in the error state it is obvious that there will be no
response so it is quite useless to wait. In fact, the timeout causes
SRP to wait a long time to reconnect when a QP error occurs. (Each
abort and each reset_device calls send_tsk_mgmt, which waits for the
timeout). The following patch solves this problem by identifying the
failure and returning an immediate error code.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Checks if the kmalloc in match_strdup() was successful, and bail out
on looking at the token if it failed.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
iSER limits the number of outstanding PDUs to send. When this threshold
is reached, it should return an error code (-ENOBUFS) instead of setting
the suspend_tx bit (which should be used only by libiscsi).
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
struct srp_device.fmr_page_mask was unsigned long, which means that
the top part of addresses above 4G was being chopped off on 32-bit
architectures. Of course nothing good happens when data from SRP
targets is DMAed to the wrong place.
Fix this by changing fmr_page_mask to u64, to match the addresses
actually used by IB devices.
Thanks to Brian Cain <Brian.Cain@ge.com> and David McMillen
<davem@systemfabricworks.com> for help diagnosing the bug and testing
the fix.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the initialization of ipoib_neigh's skb_queue into
ipoib_neigh_alloc(), since commit 2745b5b7 ("IPoIB: Fix skb leak when
freeing neighbour") will make iterate over the skb_queue to free any
packets left over when freeing the ipoib_neigh structure.
This fixes a crash when freeing ipoib_neigh structures allocated in
ipoib_mcast_send(), which otherwise don't have their skb_queue
initialized.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Convert iSER to use the new verbs DMA mapping functions for kernel
verbs consumers.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Convert SRP to use the new verbs DMA mapping functions for kernel
verbs consumers.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Convert IPoIB to use the new DMA mapping functions
for kernel verbs consumers.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove variables that are set but then never looked at in the iSER
initiator. These cleanups came from David Binderman's list of "set
but never used" warnings from icc.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This facility provides three entry points:
ilog2() Log base 2 of unsigned long
ilog2_u32() Log base 2 of u32
ilog2_u64() Log base 2 of u64
These facilities can either be used inside functions on dynamic data:
int do_something(long q)
{
...;
y = ilog2(x)
...;
}
Or can be used to statically initialise global variables with constant values:
unsigned n = ilog2(27);
When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant. They treat negative numbers as
unsigned.
When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.
[akpm@osdl.org: MMC fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conflicts:
drivers/ata/libata-scsi.c
include/linux/libata.h
Futher merge of Linus's head and compilation fixups.
Signed-Off-By: David Howells <dhowells@redhat.com>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
ipoib_neigh_free() is sometimes called while neighbour is still alive,
so it might still have queued skbs. Fix skb leak in this case.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SRP reallocates the IU buffers for tx_ring and rx_ring without freeing
the old buffers when it reconnects to a target. Fix this by keeping
the old IU buffers around.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the Scsi_Host's max_cmd_len from 12 (default) to 16 for
SRP. Otherwise scsi_dispatch_cmd() won't pass down certain commands
such as READ CAPACITY 16, required for supporting disks > 2TB.
Signed-off-by: Arne Redlich <arne.redlich@xiranet.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IPoIB assumes that high (reserved) octet in the hardware address is 0,
and copies it into the QPN. This violates RFC 4391 (which requires
that the high 8 bits are ignored on receive), and will result in an
invalid QPN being used when interoperating with IPoIB connected mode.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a connection is started (a new connection or a recovered one),
iSER should prepare its resources for full-featured mode and only then
notify the iSCSI layer that it is ready to start queueing commands.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable multiple concurrent connections to the same SRP target:
1) Use port GUID instead of node GUID in the initiator port
identifier. This allows connections to be made from multiple HCA
ports at the same time.
2) Let the user specify the identifier extention when adding the
device. This allows userspace to make multiple connections even
from the same port, if it wants too.
Without this, only one connection can be made from any given HCA, even
if it has multiple ports, because we don't use multi-channel mode, so
targets will only allow one connection from a given initiator port ID.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
scsi_host_alloc() already allocates with kzalloc(), so the struct Scsi_Host
is zeroed out, including the private data portion. Remove the redundant
memset that zeros this out again in the SRP initiator.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the description of iSER in Kconfig. It is not accurate.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
iSER uses the DMA mapping api to map the page holding the
SCSI command data to the HCA DMA address space. When the
command data is not aligned for RDMA, the data is copied
to/from an allocated buffer which in turn is used for
executing this command. The pages associated with the
command must be unmapped before being touched.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
iSER uses a data transaction object (struct iser_dto) as part
of its IB data descriptors (struct iser_desc) management.
It also uses a hierarchy of connection structures pointing to
each other. A DTO may exist even after the iscsi_iser connection
pointed by it is destroyed (eg one that is bound to a post
receive buffer which was flushed by the IB HW). Hence DTOs need
point to the lowest connection, which is struct iser_conn.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The following patches reduce the size of the VFS inode structure by 28 bytes
on a UP x86. (It would be more on an x86_64 system). This is a 10% reduction
in the inode size on a UP kernel that is configured in a production mode
(i.e., with no spinlock or other debugging functions enabled; if you want to
save memory taken up by in-core inodes, the first thing you should do is
disable the debugging options; they are responsible for a huge amount of bloat
in the VFS inode structure).
This patch:
The filesystem or device-specific pointer in the inode is inside a union,
which is pretty pointless given that all 30+ users of this field have been
using the void pointer. Get rid of the union and rename it to i_private, with
a comment to explain who is allowed to use the void pointer. This is just a
cleanup, but it allows us to reuse the union 'u' for something something where
the union will actually be used.
[judith@osdl.org: powerpc build fix]
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Judith Lebzelter <judith@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IPoIB doesn't use anything from <linux/vmalloc.h>, so don't include it.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When ipoib_ib_dev_flush() is called because of a port event, the
driver needs to rejoin all multicast groups, since the flush will call
ipoib_mcast_dev_flush() (via ipoib_ib_dev_down()). Otherwise no
(non-broadcast) multicast groups will be rejoined until the networking
core calls ->set_multicast_list again, and so multicast reception will
be broken for potentially a long time.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
RFC 4391 ("Transmission of IP over InfiniBand (IPoIB)") says:
If the IB multicast group does not already exist, one must be
created first with the IPoIB link MTU. The MGID MUST use the same
P_Key, Q_Key, SL, MTU, and HopLimit as those used in the
broadcast-GID. The rest of attributes SHOULD follow the values used
in the broadcast-GID as well.
However, the current IPoIB driver is only setting the attributes
required by the InfiniBand spec to create a multicast group, so in
particular the MTU and HopLimit are not being set. Add these
attributes when creating MCGs, and also set the Rate attribute, since
IPoIB pays attention to that attribute as well.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Require users to register with SA module, to prevent the sa_query
module text from going away while an SA query callback is still
running. Update all in-tree users for the new interface.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Split up ipoib_ib_handle_wc() into ipoib_ib_handle_rx_wc() and
ipoib_ib_handle_tx_wc() to make the code easier to read. This will
also help implement NAPI in the future.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fast Memory Registration (fmr) is used to register for rdma an sg whose
elements are not linearly sequential after dma mapping.
The IB verbs layer provides an "all dma memory MR (memory region)" which
can be used for RDMA-ing a dma linearly sequential buffer.
Change the code to use the dma mr instead of doing fmr when dma mapping
produces a single dma entry sg.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
fix and add some debug prints related to iser
handling of memory for rdma.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
As iser is able to use at most one rdma operation for the
execution of a scsi command, and registration of the sg
associated with scsi command has its restrictions, the code
checks if an sg is "aligned for rdma".
Alignment for rdma is measured in "fmr page" units whose
possible resolutions are different between HCAs and can be
smaller, equal or bigger to the system page size.
When the system page size is bigger than 4KB (eg the default
with ia64 kernels) there a bigger chance that an sg would be
aligned for rdma if the fmr page size is 4KB.
Change the code to create FMR whose pages are of size 4KB
and to take that into account when processing the sg.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently, the data length of a command coming down from scsi-ml
is limited only by the size of its sg list (sg_tablesize). The
max data length may be different for different page size values.
By setting max_sectors, we limit the data length to
max_sectors*512 bytes.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
dma mapping may include a "compaction" of the sg associated with scsi command.
Hence, the size of the maximal prefix of the SG which is aligned for rdma must be
compared against the length of the dma mapped sg (mem->dma_nents) and not against
the size of it before it was mapped (mem->size).
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Modifications to the existing rdma header files, core files, drivers,
and ulp files to support iWARP, including:
- Hook iWARP CM into the build system and use it in rdma_cm.
- Convert enum ib_node_type to enum rdma_node_type, which includes
the possibility of RDMA_NODE_RNIC, and update everything for this.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove some trailing whitespace that has snuck in despite the best
efforts of whitespace=error-all. Also fix a few other whitespace
bogosities.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add local_ib_device and local_ib_port attributes to srp scsi_host.
These are needed when we want to connect to the same target through
multiple distinct ports.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Prevent flush task from freeing the ipoib_neigh pointer, while
ipoib_start_xmit() is accessing the ipoib_neigh through the pointer it
has loaded from the skb's hardware address.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a send-only multicast group join fails, mcast->query must be set
to NULL. Otherwise, IPoIB will never retry the join and the multicast
group will never be reachable.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If there is a problem in the connection, the SCSI mid-layer will
eventually call srp_reset_host(), which will call srp_reconnect(), so
we do not need to schedule a call to srp_reconnect_work() from
srp_completion().
Removing this prevents srp_reset_host() from failing if a reconnect
scheduled from srp_completion() is already in progress, which in turn
was causing crashes as both SCSI midlayer and srp_reconnect() were
cancelling commands.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
iSCSI RFC states that the first burst length must be smaller than the
max burst length. We currently assume targets will be good, but that may
not be the case, so this patch adds a check.
This patch also moves the unsol data out offset to the lib so the LLDs
do not have to track it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
arch/ia64/hp/sim/simscsi.c
Stylistic differences in two separate fixes for buffer->request_buffer
problem.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove references to the IPoIB IETF working group as it has been closed.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Data corruption has been seen with Mellanox SRP targets when FMRs
create a memory region with I/O virtual address != 0. Add a
workaround that disables FMR merging for Mellanox targets (OUI 0002c9).
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Protect against srp_reset_device() clearing the req_queue while
srp_reconnect_target() is in progress (note that state change at
the top of srp_reconnect_target() is not sufficient for this since
srp_reset_device() ignores the state).
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When we enter recovery and flush the running commands
we cannot freee the connection before flushing the commands.
Some commands may have a reference to the connection
that needs to be released before. iscsi_stop was forcing
the term and suspend too early and was causing a oops
in iser, so this patch removes those callbacks all together
and allows the LLD to handle that detail.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The neighbour ha field may get updated without destroying the
neighbour. In this case, the ha field gets out of sync with the
address handle stored in ipoib_neigh->ah, with the result that
the ah field would point to an incorrect path, resulting in all
packets being lost.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Need to set mcast->ah before debug code dereferences it.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_fmr_pool_map_phys gets the virtual address by pointer but never writes
there, and users (e.g. srp) seem to assume this and ignore the value
returned. This patch cleans up the API to get the VA by value, and updates
all users.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Acked-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
srp_unmap_data assumes req->fmr is NULL if the request is not mapped, so we
must clean it out in case of an error.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conflicts:
drivers/scsi/nsp32.c
drivers/scsi/pcmcia/nsp_cs.c
Removal of randomness flag conflicts with SA_ -> IRQF_ global
replacement.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Roland Dreier