Added interrupt support for proximity threshold events
to the stk3310 driver.
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Minimal implementation of an IIO driver for the Sensortek
STK3310 ambient light and proximity sensor. The STK3311
model is also supported.
Includes:
- ACPI support;
- read_raw and write_raw;
- reading and setting configuration parameters for gain/scale
and integration time for both ALS and PS.
- power management
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New drivers / device support
* st sensors driver, lsm303dlh magnetometer support.
* ltr501 - support ltr301 and ltr559 chips.
New functionality
* IIO_CHAN_INFO_CALIBEMISSIVITY for thermopile sensors.
* kxcjk1013 - make driver operational with external trigger.
* Add iio targets to the tools Makefile.
Cleanups
* st sensors - more helpful error message if device id wrong or irq request
fails, explicitly make the Block Data Update optional rather
than relying on writes to address 0 not doing anything, make interrupt
support optional (Not always wired, and not all devices actually have
an interrupt line.)
* kxcjk-1013 white space additions for readability, add the KXCJ9000 ACPI
id as seen in the wild.
* sx9500 - GPIO reset support, refactor the GPIO interrupt code, add power
management, optimize power usage by powering down when possible, rename
the gpio interrupt pin to be more useful, trivial return path simplification,
trivial formatting fixes.
* isl29018 - move towards ABI compliance with a view to moving this driver
out of staging, add some brackets to ensure code works as expected. Note
there is no actual bug as the condition being tested is always true
(with current devices).
* ltr501 - add regmap support to get caching etc for later patches,
fix a parameter sanity check that always fails (bug introduced
earlier in this series), ACPI enumeration support,
interrupt rate control support, interrupt support in general and
integration time control support, code alignment cleanups.
* mma9553 - a number of little cleanups following a review from Hartmut
after I'd already applied the original driver patch.
* tmp006 - prefix some defines with TMP006 for consistency.
* tsl4531 - cleanup some wrong prefixes, presumably from copy and paste.
* mlx90614 - check for errors in read values, add power management,
add emissivity setting, add device tree binding documentation,
fix a duplicate const warning.
* ti_am335x_adc - refactor the DT parsing into a separate function.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wyz7
-----END PGP SIGNATURE-----
Merge tag 'iio-for-v4.2a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new drivers, functionality and cleanups for the 4.2 cycle
New drivers / device support
* st sensors driver, lsm303dlh magnetometer support.
* ltr501 - support ltr301 and ltr559 chips.
New functionality
* IIO_CHAN_INFO_CALIBEMISSIVITY for thermopile sensors.
* kxcjk1013 - make driver operational with external trigger.
* Add iio targets to the tools Makefile.
Cleanups
* st sensors - more helpful error message if device id wrong or irq request
fails, explicitly make the Block Data Update optional rather
than relying on writes to address 0 not doing anything, make interrupt
support optional (Not always wired, and not all devices actually have
an interrupt line.)
* kxcjk-1013 white space additions for readability, add the KXCJ9000 ACPI
id as seen in the wild.
* sx9500 - GPIO reset support, refactor the GPIO interrupt code, add power
management, optimize power usage by powering down when possible, rename
the gpio interrupt pin to be more useful, trivial return path simplification,
trivial formatting fixes.
* isl29018 - move towards ABI compliance with a view to moving this driver
out of staging, add some brackets to ensure code works as expected. Note
there is no actual bug as the condition being tested is always true
(with current devices).
* ltr501 - add regmap support to get caching etc for later patches,
fix a parameter sanity check that always fails (bug introduced
earlier in this series), ACPI enumeration support,
interrupt rate control support, interrupt support in general and
integration time control support, code alignment cleanups.
* mma9553 - a number of little cleanups following a review from Hartmut
after I'd already applied the original driver patch.
* tmp006 - prefix some defines with TMP006 for consistency.
* tsl4531 - cleanup some wrong prefixes, presumably from copy and paste.
* mlx90614 - check for errors in read values, add power management,
add emissivity setting, add device tree binding documentation,
fix a duplicate const warning.
* ti_am335x_adc - refactor the DT parsing into a separate function.
The LSM303DLH accelerometer/magnetometer has a different
device identification method than using register 0x0f, instead
three registers contain a magic value. We rely on WhoAmI
to be zero for this variant.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ST sensors are detected by reading a WhoAmI register and
matching the number found to a sensor name string. To make it
easier to figure out what happens when things go wrong, print
the WhoAmI value and the device name we're trying to match.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Not all sensors support BDU (block data update) and in fact a
bunch of the in-kernel sensor settings do not specify the
BDU address field. Make this optional.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some sensors such as magnetometers and pressure sensors doesn't
have interrupts at all, and thus no DRDY setting applies. Make
the assignment of an interrupt optional, and do not call
st_sensors_set_drdy_int_pin() if there is no drdy (data ready)
pin specified.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Print a proper error message if we're missing the trigger
IRQ.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some extra blank lines between if checks don't hurt and improve
readability.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This id has been seen in the DSDT of the Teclast X98 Air 3G tablet based
on Intel Bay Trail.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Clearly the intent was to error if the value was not 0 or 1.
As implemented we have (A != 0 || A != 1) which is always true
as A is never both 0 and 1 at the same time.
As the autobuilder suggested, && makes more sense for this error
check.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Initial value of gpio bitnum is set to -1, but
the variable is declared as unsigned.
Use a positive invalid value for initial gpio
bitnum.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Suggested-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add mma9553_ prefix to all local functions/declarations.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Suggested-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use GENMASK instead of BIT or direct value to
define a mask.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Suggested-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use "GPIO" instead of "gpio" and "ACPI" instead of "acpi".
Includes a couple of small style fixes in comments
(missing full stop, whitespace, paranthesis).
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Suggested-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use return 0 instead of return ret to mark
clearly the success return path.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Suggested-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When configuring gpio, we need to read initial values for activity and
step count. This function may fail due to i2c read errors.
Check the error code returned by mma9553_read_activity_stepcnt
and return the appropriate error in gpio config function.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for Liteon 301 Ambient light sensor. Since
LTR-301 and LTR-501 are register compatible(and even have same
part id), LTR-501 driver has been extended to support both
devices. LTR-501 is similar to LTR-301 in ALS sensing, But the
only difference is, LTR-501 also supports proximity sensing.
LTR-501 - ALS + Proximity combo
LTR-301 - ALS sensor.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This device is register compatible with LTR501, with a minor difference for
ALS control register as showed below:
ALS Control register for LTR501:
7 6 5 4 3 2 1 0
+------+------+------+------+------+------+------+------+
| | | | |
| Reserved | Gain | SW | ALS Mode |
| | | Reset| |
+------+------+------+------+------+------+------+------+
ALS Control register for LTR559:
7 6 5 4 3 2 1 0
+------+------+------+------+------+------+------+------+
| | | | |
| Reserved | Gain | SW | ALS |
| | | Reset| Mode |
+------+------+------+------+------+------+------+------+
We handle this difference by introducing ltr501_chip_info.
Datasheet for LTR559 is at:
http://optoelectronics.liteon.com/upload/download/DS86-2013-0003/S_110_LTR-559ALS-01_DS_V1.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added ACPI enumeration support for LTR501 chip.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added rate control support for ALS and proximity
threshold interrupts.Also, Added support to modify
and read ALS & proximity sensor sampling frequency.
LTR-501 supports interrupt rate control using persistence
register settings. Writing <n> to persistence register
would generate interrupt only if there are <n> consecutive
data values outside the threshold range.
Since we don't have any existing ABI's to directly
control the persistence register count, we have implemented
the rate control using IIO_EV_INFO_PERIOD. _period event
attribute represents the amount of time in seconds an
event should be true for the device to generate the
interrupt. So using _period value and device frequency,
persistence count is calculated in driver using following
logic.
count = period / measurement_rate
If the given period is not a multiple of measurement rate then
we round up the value to next multiple.
This patch also handles change to persistence count whenever
there is change in frequency.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds interrupt support for Liteon 501 chip.
Interrupt will be generated whenever ALS or proximity
data exceeds values given in upper and lower threshold
register settings.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support to modify and read ALS integration time.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If a GPIO reset pin is listed in ACPI or Device Tree, use it to reset
the device on initialization.
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In the interest of lowering power usage, we only activate the proximity
channels and interrupts that we are currently using.
For raw reads, we activate the corresponding channel and the data ready
interrupt and wait for the interrupt to trigger. If no interrupt is
available, we wait for the documented scan period, as specified in the
datasheet.
The following types of usage patterns may overlap:
* raw proximity reads (need a single data ready interrupt)
* trigger usage (needs data ready interrupts as long as active)
* proximity events (need near/far interrupts)
* triggered buffer reads (don't need any interrupts, but are usually
coupled with our own trigger.
To mitigate all possible patterns, we implement usage counting for all
the resources used: data ready interrupts, near/far interrupts and
individual channels.
The device enters sleep mode as documented in the data sheet when its
buffer, trigger and events are disabled, and no raw reads are currently
running.
Because of this new usage pattern, it is important that we give the
device a chance to perform an initial compensation for all its channels
at probe time.
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix a typo triggering a duplicate const warning on some compilers.
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Cc: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added regmap support. It will be useful to handle
bitwise updates to als & ps control registers.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
Pull HID updates from Jiri Kosina:
- quite a few firmware fixes for RMI driver by Andrew Duggan
- huion and uclogic drivers have been substantially overlaping in
functionality laterly. This redundancy is fixed by hid-huion driver
being merged into hid-uclogic; work done by Benjamin Tissoires and
Nikolai Kondrashov
- i2c-hid now supports ACPI GPIO interrupts; patch from Mika Westerberg
- Some of the quirks, that got separated into individual drivers, have
historically had EXPERT dependency. As HID subsystem matured (as
well as the individual drivers), this made less and less sense. This
dependency is now being removed by patch from Jean Delvare
- Logitech lg4ff driver received a couple of improvements for mode
switching, by Michal Malý
- multitouch driver now supports clickpads, patches by Benjamin
Tissoires and Seth Forshee
- hid-sensor framework received a substantial update; namely support
for Custom and Generic pages is being added; work done by Srinivas
Pandruvada
- wacom driver received substantial update; it now supports
i2c-conntected devices (Mika Westerberg), Bamboo PADs are now
properly supported (Benjamin Tissoires), much improved battery
reporting (Jason Gerecke) and pen proximity cleanups (Ping Cheng)
- small assorted fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
HID: sensor: Update document for custom sensor
HID: sensor: Custom and Generic sensor support
HID: debug: fix error handling in hid_debug_events_read()
Input - mt: Fix input_mt_get_slot_by_key
HID: logitech-hidpp: fix error return code
HID: wacom: Add support for Cintiq 13HD Touch
HID: logitech-hidpp: add a module parameter to keep firmware gestures
HID: usbhid: yet another mouse with ALWAYS_POLL
HID: usbhid: more mice with ALWAYS_POLL
HID: wacom: set stylus_in_proximity before checking touch_down
HID: wacom: use wacom_wac_finger_count_touches to set touch_down
HID: wacom: remove hardcoded WACOM_QUIRK_MULTI_INPUT
HID: pidff: effect can't be NULL
HID: add quirk for PIXART OEM mouse used by HP
HID: add HP OEM mouse to quirk ALWAYS_POLL
HID: wacom: ask for a in-prox report when it was missed
HID: hid-sensor-hub: Fix sparse warning
HID: hid-sensor-hub: fix attribute read for logical usage id
HID: plantronics: fix Kconfig default
HID: pidff: support more than one concurrent effect
...
Here's the big staging driver patchset for 4.1-rc1.
There's a lot of patches here, the Outreachy application period happened
during this development cycle, so that means that there was a lot of
cleanup patches accepted. Other than the normal coding style and sparse
fixes here, there are some driver updates and work toward making some of
the drivers into "mergable" shape (like the Unisys drivers.)
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlUsIA0ACgkQMUfUDdst+ylHuACgm8QZ9S6lk45/Qd9YeR3NSDaS
upoAn3gVAaHnuxkW3anivuwOcirgCp3l
=7VHU
-----END PGP SIGNATURE-----
Merge tag 'staging-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big staging driver patchset for 4.1-rc1.
There's a lot of patches here, the Outreachy application period
happened during this development cycle, so that means that there was a
lot of cleanup patches accepted. Other than the normal coding style
and sparse fixes here, there are some driver updates and work toward
making some of the drivers into "mergable" shape (like the Unisys
drivers.)
All of these have been in linux-next for a while"
* tag 'staging-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1214 commits)
staging: lustre: orthography & coding style
staging: lustre: lnet: lnet: fix error return code
staging: lustre: fix sparse warning
Revert "Staging: sm750fb: Fix C99 Comments"
Staging: rtl8192u: use correct array for debug output
staging: rtl8192e: Remove dead code
staging: rtl8192e: Comment cleanup (style/format)
staging: rtl8192e: Fix indentation in rtllib_rx_auth_resp()
staging: rtl8192e: Decrease nesting of rtllib_rx_auth_resp()
staging: rtl8192e: Divide rtllib_rx_auth()
staging: rtl8192e: Fix PRINTK_WITHOUT_KERN_LEVEL warnings
staging: rtl8192e: Fix DO_WHILE_MACRO_WITH_TRAILING_SEMICOLON warning
staging: rtl8192e: Fix BRACES warning
staging: rtl8192e: Fix LINE_CONTINUATIONS warning
staging: rtl8192e: Fix UNNECESSARY_PARENTHESES warnings
staging: rtl8192e: remove unused EXPORT_SYMBOL_RSL macro
staging: rtl8192e: Fix RETURN_VOID warnings
staging: rtl8192e: Fix UNNECESSARY_ELSE warning
staging: rtl8723au: Remove unneeded comments
staging: rtl8723au: Use __func__ in trace logs
...
* new API for safe access of power supply function attrs
* devres support for power supply (un)registration
* new drivers / chips
- generic syscon based poweroff driver
- iio & charger driver for da9150
- fuel gauge driver for axp288
- bq27x00: add support for bq27510
- bq2415x: add support for bq24157s
* twl4030-madc-battery: convert to iio consumer
* misc fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WbZu
-----END PGP SIGNATURE-----
Merge tag 'for-v4.1' of git://git.infradead.org/battery-2.6
Pull power supply and reset changes from Sebastian Reichel:
- new API for safe access of power supply function attrs
- devres support for power supply (un)registration
- new drivers / chips:
- generic syscon based poweroff driver
- iio & charger driver for da9150
- fuel gauge driver for axp288
- bq27x00: add support for bq27510
- bq2415x: add support for bq24157s
- twl4030-madc-battery: convert to iio consumer
- misc fixes
* tag 'for-v4.1' of git://git.infradead.org/battery-2.6: (66 commits)
power: twl4030_madc_battery: Add missing MODULE_ALIAS
power: twl4030-madc-battery: Convert to iio consumer.
dt: power: Add docs for generic SYSCON poweroff driver.
power: reset: Add generic SYSCON register mapped poweroff.
power: max17042_battery: add missed blank
power: max17042_battery: Use reg type instead of chip type
power/reset: at91: big endian fixes for atsama5d3x
power_supply: charger-manager: Fix dereferencing of ERR_PTR
HID: input: Fix NULL pointer dereference when power_supply_register fails
power: constify of_device_id array
power/reset/rmobile-reset.c: Fix !HAS_IOMEM build
power_supply: 88pm860x_charger: Fix possible NULL pointer dereference and use of initialized variable
arm: mach-pxa: Decrement the power supply's device reference counter
mfd: ab8500: Decrement the power supply's device reference counter
power_supply: bq2415x_charger: Decrement the power supply's device reference counter
power_supply: 88pm860x_charger: Decrement the power supply's device reference counter
x86/olpc/xo15/sci: Use newly added power_supply_put API
x86/olpc/xo1/sci: Use newly added power_supply_put API
power_supply: charger-manager: Decrement the power supply's device reference counter
power_supply: Increment power supply use counter when obtaining references
...
This makes ltr501 code consistent with the coding style adopted
for the new drivers added to IIO.
We prepare the path for adding support for LTR559 chip.
Reported by checkpatch.pl
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Refactor DT parsing into a separate function from probe() to
help addition of more DT parameters later.
No functional changes.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The device uses the MSB of the returned temperature value as an error
flag. Return a read error when this bit is set.
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Cc: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for system sleep and runtime power management.
To wake up the device, the SDA line should be held low for at least 33ms
while SCL is high. As this is not possible using the i2c API (and not
supported by all i2c adapters), a GPIO connected to the SDA line is
needed. The GPIO is named "wakeup" and can be specified in a device
tree with the "wakeup-gpios" binding.
If the wake-up GPIO is not given, disable power management for the
device. Entering sleep requires an SMBus byte access, hence power
management is also disabled if byte access is not supported by the
adapter.
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Cc: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The mapping from the 16-bit EEPROM value to the decimal 0-1 range is
approximate. A special case ensures 0xFFFF shows as 1.0 instead of
0.999998565.
Writing to EEPROM requires an explicit erase by writing zero. In
addition, it takes 20ms for the erase/write to complete. During this
time no EEPROM register should be accessed. Therefore, two msleep()s
are added to the write function and a mutex protects against concurrent
access.
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Cc: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Contact-less IR temperature sensors measure the temperature of an object
by using its thermal radiation. Surfaces with different emissivity
ratios emit different amounts of energy at the same temperature.
IIO_CHAN_INFO_CALIBEMISSIVITY allows the user to inform the sensor of the
emissivity of the object in front of it, in order to effectively measure
its temperature.
A device providing such setting is Melexis's MLX90614:
http://melexis.com/Assets/IR-sensor-thermometer-MLX90614-Datasheet-5152.aspx.
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Cc: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In its present state, the driver mandates that its buffer only be
triggered by one of the device's own triggers (data ready or any
motion). This is not always desirable, for example because the
interrupt pins may not be wired in.
Patch the driver to be able to accept using an external trigger, such as
one based on hrtimer. When using such a trigger, we need to ensure that
the device is powered on when the buffer is started. We do that by
setting setup_ops for the buffer.
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Tiberiu Breana