Add comments to Tx commands
Clean up unused definitions in iwl-3945-commands.h
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add comments to QOS and ADD_STA commands
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add comments to RXON command and txpower formats
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document command header and "alive" responses
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document 4965 Tx scheduler
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document shared Tx structures
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document Tx registers
Clean up unused definitions
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document Rx registers
Document Tx circular buffer base registers
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document txpower calculations
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document temperature calculation
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move HT_IE_EXT_CHANNEL_* driver definitions to iwl-4965.h
Add comments to guide .h file usage (hw/api/driver definitions)
Minor comment cleanup
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move uCode API definitions to iwl-4965-commands.h
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up unused definitions in iwl-4965-hw.h
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up unused definitions in iwl-3945-hw.h
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add comments to iwlXXXX-base.c
Signed-off-by: Cahill, Ben M <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add comments, mostly on Tx queues
Signed-off-by: Cahill, Ben M <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up some unused definitions in iwl-4965.h and iwl-3945.h
Move STA_FLG_ definitions to iwl-4965-commands.h
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Partially clean-up, add comments to iwl-XXXX-hw.h
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document Rx calibration
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document 4965 rate_n_flags bits
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add comments to some driver data structures
Remove unused "sched_retry" member from struct iwl3945_tx_queue
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move is_legacy() macro family from iwl-4965-hw.h to iwl-4965-rs.h
These macros are for driver's rate scaling implementation, and are not
related to hardware or uCode API values (moved from iwl-4965-hw.h).
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up and clarify some comments after 3945/4965 split.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up unused eeprom structures and definitions in iwl-4965-hw.h.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add comments to EEPROM stuff.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add comments to rate scaling code.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Re-align 3945 event log data.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Remove HT code from iwl-3945.h - it is not needed here as 3945
does not support HT. The code ended up here during the header file
split.
- Modify a few places where the CONFIG variables were named
incorrectly: all changes are to comments only.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables loading fw w/o init and bsm section. It also provides
general cleanup of the rutine.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The label exit_free_polldev is no longer used and can be removed.
input_free_polled_device() also calls input_free_device(), so
don't call it seperatly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rt2x00rfkill.c, routine input_allocate_device() is called even though
input_allocate_polled_device(), which was just called, includes a call to
that routine. This patch, which has not been tested, removes the redundant code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restrict rssi average updating to beacon frames of the bssid the
interface is
associated with. Without this restriction, strong signals belonging to other
BSS, e.g. beacon frames coming from a nearby AP, would cause incorrectly high
rssi approximation values. This would then cause the link tuner to reduce
sensitivity, resulting in transmissions from the BSS associated to to be
missed.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to use a seperate define INVALID_INTERFACE while
we can use IEEE80211_IF_TYPE_INVALID directly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds TX/RX frame dumping capabilities through debugfs.
The intention is that with this approach debugging of rt2x00 is
simplified since _all_ frames going in and out of the device
are send to debugfs as well along with additional information
like the hardware descriptor.
Based on the patch by Mattias Nissler.
Mattias also has some tools that will make the dumped frames
available to wireshark: http://www-user.rhrk.uni-kl.de/~nissler/rt2x00/
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the skb->cb field to add a frame description that can be used
to transfer information passed each rt2x00 layer. This reduces the
required arguments for rt2x00lib_write_tx_desc().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chipset debugfs entry already indicates it is about the chipset,
it only makes sense to also display the chipset version in there.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cleanup debugfs interface by moving the csr/bbp/rf/eeprom value/offset
entries into the "register" folder.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend word field definitions for the PLCP words
in the TX descriptor to contain the BBP fields as well.
This will remove rt2400pci_write_tx_desc() from the
checkstack script.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DRV_NAME was always set to the KBUILD_MODNAME value,
lets clean everything up by removing DRV_NAME and just
use KBUILD_MODNAME directly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restart the hardware on too many PHY TX errors. A thousand PHY TX errors
per 15 seconds means we won't be able to recover for sure.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When monitor mode is enabled, this will make b43legacy read out
the full 64-bit MAC time from the chip for each received packet.
This patch has been ported from b43.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use initialized_var() to properly fix a bogus gcc warning.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BCM94311MCG rev 02 chip has an 802.11 core with revision 13 and
has not been supported until now. The changes include the following:
(1) Add the 802.11 rev 13 device to the ssb_device_id table to load b43.
(2) Add PHY revision 9 to the supported list.
(3) Change the 2-bit routing code for address extensions to 0b10 rather
than the 0b01 used for the 32-bit case.
(4) Remove some magic numbers in the DMA setup.
The DMA implementation for this chip supports full 64-bit addressing with
one exception. Whenever the Descriptor Ring Buffer is in high memory, a
fatal DMA error occurs. This problem was not present in 2.6.24-rc2 due
to code to "Bias the placement of kernel pages at lower PFNs". When
commit 44048d70 reverted that code, the DMA error appeared. As a "fix",
use the GFP_DMA flag when allocating the buffer for 64-bit DMA. At present,
this problem is thought to arise from a hardware error.
This patch has been tested on my system and by Cédric Caumont
<icare40@hotmail.com>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restart the hardware on too many PHY TX errors. A thousand PHY TX errors
per 15 seconds means we won't be able to recover for sure.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes it can be useful to see the FCS, especially when
bad-FCS frames are shown. Pass the FCS to mac80211 and let
it worry about snipping it off when required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When monitor mode is enabled, this will make b43 read out the
full 64-bit MAC time from the chip for each received packet.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* only shift eventcause once
* convert mac events to decimal, as this is what the firmware
manual uses in section 6.1, too
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the ability to specify channels to scan via debugfs
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the ability to specify number of probes via debugfs
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make two functions in the TX packet path emit
their debug messages with LBS_DEB_TX, not LBS_DEB_MAIN.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change debug output codes from LBS_DEB_JOIN to LBS_DEB_ASSOC
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves re-works the implementation of event subscription
via debugfs. For this:
* it tells cmd.c and cmdresp.c about CMD_802_11_SUBSCRIBE_EVENT
* removes lots of low-level cmd stuff from debugfs.c
* create unified functions to read/write snr, rssi, bcnmiss and
failcount
* introduces #define's for subscription event bitmask values
* add a function to search for a specific element in an IE
(a.k.a. TLV)
* add a function to find out the size of the TLV. This is needed
because lbs_prepare_and_send_command() has an argument for a
data buffer, but not for it's lengths and TLVs can be, by
definition, vary in size.
* fix a bug where it was not possible to disable an event
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New typedefs are usually frowned upon. This patch changes
libertas_adapter -> struct libertas_adapter
libertas_priv -> struct libertas_priv
While passing, make everything checkpatch.pl-clean that gets touches.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Requires firmware version 5.110.19.p0 or newer, available here:
http://dev.laptop.org/pub/firmware/libertas/
Signed-off-by: Ashish Shukla <ashishs@marvell.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The transmit and receive traffic as soon as the mesh interface is
brought up.
Test case 1: Bring up only the mesh interface and ping. No need for
any iwconfig commands on the main interface.
$ ifconfig msh0 192.168.5.3
$ iwconfig msh0 channel X
$ ping 192.168.5.2
If ping succeeds, PASS
Test case 2: Associate with the main interface, and turn off AP. Mesh
interface should not lose connectivity.
$ iwconfig eth0 mode managed essid "my_ssid"
$ ifconfig msh0 192.168.5.3
$ ping 192.168.5.2
<turn off access point>
If ping continues uninterrupted, PASS
This feature requires firmware version 5.110.19.p0 or newer, available
here: http://dev.laptop.org/pub/firmware/libertas/
Signed-off-by: Ashish Shukla <ashishs@marvell.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I think it was pretty obvious what fields in if_usb_driver are...
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Do not reset libertas devices upon module unload. We're unloading
the module, we're not killing off devices.
2) Instead, reset libertas devices inside if_usb_disconnect, as we're
killing off interfaces and so on.
3) Resetting via disconnect callback means we no longer need to keep
track of probed libertas devices; kill off that list (and its wonderful
lack of locking..), as well.
Drop a useless comment as well.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by chloubs on IRC
zd1211 chip 157e:300a v4810 high 00-11-e0 AL7230B_RF pa0 g----
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This seems to be working smoothly now. Let's not hold back the mac80211
transition any further. This patch ports the existing driver from softmac
to mac80211.
Many thanks to everyone who helped out with the porting efforts.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the debug output of all association stuff clearer by:
* adding some lbs_deb_enter()/lbs_deb_leave() calls
* printing the return level in one place
* lower-casing some string
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unifies the namespace of variables, functions defines
and structures. It does:
- rename libertas_XXX to lbs_XXX
- rename LIBERTAS_XXX to lbs_XXX
- rename wlan_XXX to lbs_XXX
- rename WLAN_XXX to LBS_XXX (but only those that were
defined in libertas-local *.h files, e.g. not defines
from net/ieee80211.h)
While passing, I fixed some checkpatch.pl errors too.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Problem identified by Miguel Botón <mboton.lkml@gmail.com>, alternate
solution suggested by Zhu Yi <yi.zhu@intel.com>, patch by me. :-)
Cc: Miguel Botón <mboton.lkml@gmail.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The b43legacy driver is modified to use the new SPROM structure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The b43 driver is modified to use the new SPROM structure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The b44 driver is changed to use the new SPROM data structure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2400pci, rt2500pci and rt61 require different
txdone handling, but the code that pushes the frame
upstream and cleans up the entry is identical to
all of them.
This will create the function rt2x00pci_txdone()
to remove the duplicate code.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes a bug that enables RXON_FLG_TGG_PROTECT_MSK erroneously
for A mode in the erp_ie_changed mac80211 callback.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use uninitialized_var() to avoid the following bogus warning:
CC [M] drivers/net/wireless/b43/debugfs.o
drivers/net/wireless/b43/debugfs.c: In function ‘b43_debugfs_read’:
drivers/net/wireless/b43/debugfs.c:355: warning: ‘ret’ may be used uninitialized in this function
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix dependencies for built-in b43legacy.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch removes the unused function to fix a recursive bug caused
by namespace change.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prefix all symbols with iwl3945_ or iwl4965_ and thus allow building
the driver into the kernel. Also remove all the useless default
statements in Kconfig while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the iwl4965 problem for "Can not find a suitable rate
issues." by making rs_switch_to_mimo and rs_switch_to_siso functions
return -1 when CONFIG_IWL4965_HT is not selected. They used to return 0,
which means we can switch to HT rate causing the rate scale problem and
the error message.
The patch also fix another bug reported by Ben Cahill that it uses wrong
value for max_success_limit.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace 0x8086 with PCI_VENDOR_ID_INTEL for PCI_DEVICE declaration.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix my copyright notices in b43 and b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rewrite and sync A PHY initialization with specs, thus allowing for further
work to be done on 802.11a support. Note that A PHY initialization involves
G PHYs as well.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rfkill subsystem doesn't like code like that
rfkill_allocate();
rfkill_register();
rfkill_unregister();
rfkill_register(); /* <- This will crash */
This sequence happens with
modprobe b43
ifconfig wlanX up
ifconfig wlanX down
ifconfig wlanX up
Fix this by always re-allocating the rfkill stuff before register.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a consistent naming scheme for the ops.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the retry limits provided by mac80211.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SGI IP28 machines would need special treatment (enable adding addtional
wait states) when accessing memory uncached. To avoid this pain I changed
the driver to use only cached access to memory.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: Don't enable RX/TX without a link (if possible)
Don't enable RX/TX of packets until we have a link, since there's a chance
we'll just get RX frame errors, etc.
The case where we don't have a PHY we can't do much about: Just enable
it and deal with errors as they come in.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: Print warning when not attaching to a PHY
Print a warning on the console when not connecting to a phy for an interface.
It turns out to be a pretty common problem when someone gets the MDIO info
wrong in their device tree, resulting in the macs running at a fixed 1Gbit FD.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: Remove SKB copy/recycle logic
It doesn't really buy us much, since copying is about as expensive
as the allocation in the first place. Just remove it for now.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: SKB unmap optimization
Avoid touching skb_shinfo() in the unmap path, since it turns out to
normally cause cache misses and delays. instead, save number of fragments
in the TX_RING_INFO structures since that's all that's needed anyway.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: Software-based LRO support
Implement LRO for pasemi_mac. Pretty straightforward.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: Improve RX interrupt mitigation
Currently the receive side interrupts will go off on the reception of
a packet, NAPI will poll the ring and keep polling as long as there's
a decent amount of packets to receive.
This is less than optimal, especially for LRO where it's better if we
have a more substantial amount of packets to process at once, to get
the real LRO benefits.
So, set the count threshold to a higher value and use the timeout feature
that will give us an interrupt even if not enough packets have come in
to set off the count threshold.
FIXME: It'd be real nice to have ethtool support for users to tune this
at runtime.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: Fix TX cleaning
This is a bit awkward. We don't have a timer-delayed interrupt on TX
complete, but we have a count threshold. So set that reasonably high
(32 packets), and schedule the NAPI poll when it goes off. Also bump a
regular timer that will take care of rotting packets for the last 1..31
ones in case we don't trigger a TX interrupt (and there's no RX activity
that would otherwise trigger the poll).
The longer-term fix is to separate TX from RX NAPI and do two separate
poll loops.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: performance tweaks
* Seems like we do better with a smaller RX ring, probably because chances of
still having the SKB cached are better
* Const-ify variables to get better code generation and fewer reloads
* Move prefetching around a little, and try to prefetch the whole SKB
* Set NETIF_F_HIGHDMA
* Misc other minor tweaks
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: Convert to new dma library
Convert the pasemi_mac driver to the new platform global DMA manaagement
library. This also does a couple of other minor cleanups w.r.t. channel
management.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: Move register definitions to include/asm-powerpc
Move the common register formats and descriptor layouts from
drivers/net/pasemi_mac.h to include/asm-poewrpc/pasemi_dma.h
Previously only the ethernet driver was using them, but other drivers
are coming up that will also use them, so it makes sense to share the
constants.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: RX/TX ring management cleanup
Prepare a bit for supporting multiple TX queues by cleaning up some
of the ring management and shuffle things around a bit.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When using larger MTU's sky2 driver changes from allocating one
data area, to using multiple pages. The threshold for this was based on
a heuristic where the cost of a single allocation is bigger than one
page. Since the allocator has changed, this heuristic is now incorrect;
instead just make the threshold be when the total size of the allocation
is greater than one page.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sky2 driver was not aligning the IP header on receive buffers.
This workaround is only needed on hardware with broken FIFO, newer chips
without FIFO can just DMA to unaligned address.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- whitespaces vs tabs
- use 80 cols
- use if_mii
- use netdev_priv
- remove useless cast to void *
- PCI device id does not need to be globally available
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
drivers/net/r6040.c: In function 'rx_buf_alloc':
drivers/net/r6040.c:262: warning: passing argument 2 of 'pci_map_single' makes pointer from integer without a cast
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Disable PEX errors. The HW generates false positives.
Update RSS hash function to a symmetric algorithm.
Update T3C HW support
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Do not use skb->cb to stash unmap info,
save the info to the descriptor state.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bump up FW version to 5.0.
Do not downgrade FW within the same major version range.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Subdevice ID is not necessarily set to 1.
Use wild card for PCI device matching
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
dm_write_async and dm_write_reg_async are almost identical.
Move common functionality to dm_write_async_helper (saves ~256b).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch #if 0's the following unused functions:
- espi.c:t1_espi_set_misc_ctrl()
- sge.c:t1_sched_set_max_avail_bytes()
- sge.c:t1_sched_set_drain_bits_per_us()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Support to add/delete/store/restore 64 and 128 Ethernet addresses for Xframe I and Xframe II respectively.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring secondary unicast addresses. Unicast
addresses take precendece over multicast addresses when filling
the exact address filters to avoid going to promiscous mode.
When more unicast addresses are present than filter slots,
unicast filtering is disabled and all slots can be used for
multicast addresses.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions for reg_pattern_test and reg_set_and check
Changed macros to use these functions
Compiled x86, untested
Size decreased ~2K
old:
$ size drivers/net/e1000e/ethtool.o
text data bss dec hex filename
14461 0 0 14461 387d drivers/net/e1000e/ethtool.o
new:
$ size drivers/net/e1000e/ethtool.o
text data bss dec hex filename
12498 0 0 12498 30d2 drivers/net/e1000e/ethtool.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minimal macro to function conversion in e1000_ethtool.c
Adds functions reg_pattern_test and reg_set_and_check
Changes REG_PATTERN_TEST and REG_SET_AND_CHECK macros
to call these functions.
Saves ~2.5KB
Compiled x86, untested (no hardware)
old:
$ size drivers/net/e1000/e1000_ethtool.o
text data bss dec hex filename
16778 0 0 16778 418a drivers/net/e1000/e1000_ethtool.o
new:
$ size drivers/net/e1000/e1000_ethtool.o
text data bss dec hex filename
14128 0 0 14128 3730 drivers/net/e1000/e1000_ethtool.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
formerly e1000/e1000e only updated traffic counters once every
2 seconds with the register values of bytes/packets. With newer
code however in the interrupt and polling code we can real-time
fill in these values in the netstats struct for users to see.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
formerly e1000/e1000e only updated traffic counters once every
2 seconds with the register values of bytes/packets. With newer
code however in the interrupt and polling code we can real-time
fill in these values in the netstats struct for users to see.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the RDC R6040 MAC we can find in the RDC
R-321x System-on-chips.
Signed-off-by: Sten Wang <sten.wang@rdc.com.tw>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
On the systems that have cache incoherent DMA, including ARM, there
is a race condition between software allocating a new receive buffer
and hardware writing into a buffer. The two race on touching the last
Receive Frame Descriptor (RFD). It has its el-bit set and its next
link equal to 0. When hardware encounters this buffer it attempts to
write data to it and then update Status Word bits and Actual Count in
the RFD. At the same time software may try to clear the el-bit and
set the link address to a new buffer.
Since the entire RFD is once cache-line, the two write operations can
collide. This can lead to the receive unit stalling or interpreting
random memory as its receive area.
The fix is to set the el-bit on and the size to 0 on the next to last
buffer in the chain. When the hardware encounters this buffer it stops
and does not write to it at all. The hardware issues an RNR interrupt
with the receive unit in the No Resources state. Software can write
to the tail of the list because it knows hardware will stop on the
previous descriptor that was marked as the end of list.
Once it has a new next to last buffer prepared, it can clear the el-bit
and set the size on the previous one. The race on this buffer is safe
since the link already points to a valid next buffer and the software
can handle the race setting the size (assuming aligned 16 bit writes
are atomic with respect to the DMA read). If the hardware sees the
el-bit cleared without the size set, it will move on to the next buffer
and skip this one. If it sees the size set but the el-bit still set,
it will complete that buffer and then RNR interrupt and wait.
Signed-off-by: David Acker <dacker@roinet.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To quote one of my favorite contemporary author:
[include/linux/sockios.h]
* THESE IOCTLS ARE _DEPRECATED_ AND WILL DISAPPEAR IN 2.5.X -DaveM
*/
#define SIOCDEVPRIVATE 0x89F0 /* to 89FF */
[...]
Gentoo's snmpd trips up over this code when trying to figure if the driver
supports the non-SIOCDEVPRIVATE API or not. One can argue over its choice
of heuristic but there no reason to make ioctl more ugly than needed.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jesse Huang <jesse@icplus.com.tw>
Tested-by: Volker Sauer <vsauer@dvs.tu-darmstadt.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains the following cleanups:
- static functions in .c files shouldn't be marked inline
- make needlessly global code static
- #if 0 unused code
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
While cleaning up the internal API focussing on Fiber and CX4 code
we found that I had broken the copper PHY initialization code. This
patch restores the PHY-specific code. This is mostly uninteresting
since no copper PHY boards are yet available. The changes have been
tested against Fiber only as I do not even have copper PHY versions
of 82598 macs.
This change actually cleans up the API code a bit more and we
lose some initialization code. A few PHY link detection helper
lines of code have been snuck into this patch, as well as a
read flush where it was suspected that this might cause issues.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
e1000e will from now on support the PCI-Express adapters that
previously were supported by e1000. This support means better
performance and easier debugging from now on for both the old
PCI-X/PCI hardware and PCI-Express adapters.
This patch also moves 3 recently merged device IDs over to e1000e
that are identical to quad-port versions of already existing
dual port versions. With this last bit every former e1000 pci-e
device should work now with e1000e.
Here is a brief list of which gigabit driver to use with which
adapter:
e1000:
82540 -> 82547
e1000e:
82571 -> 82573
ich8, ich9 (82562 or 82566)
es2lan (80003eslan)
igb: (not yet merged, only available from e1000.sf.net)
82575
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
L1 ASPM link (pci-e link power savings) has significant benefits
(~1W savings when link is active) but unfortunately does not work
correctly on any of the chipsets that have 82573 on mobile platforms
which causes various nuisances:
- eeprom reads return garbage information leading to bad eeprom
checksums
- long ping times (up to 2 seconds)
- complete system hangs (freeze/lockup)
A lot of T60 owners have been plagued by this, but other mobile
solutions also suffer from these symptoms.
Disabling L1 ASPM before we activate the PCI-E link fixes all of
these issues at the cost of some power consumption.
Remove a workaround RDTR adjustment that is no longer needed with
this new one.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Port alternate MAC address support from the sourceforge
e1000 driver to the upstream e1000e driver.
Signed-off-by: Bill Hayes <bill.hayes@hp.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* use irq_handler_t where appropriate
* no need to use 'irq' function arg, its already stored in a data struct
* rename irq handler 'irq' argument to 'dummy', where the function
has been analyzed and proven not to use its first argument.
* remove always-false "dev_id == NULL" test from irq handlers
* remove pointless casts from void*
* declance: irq argument is not const
* add KERN_xxx printk prefix
* fix minor whitespace weirdness
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This converts uses of ARRAY_SIZE(), and while at it also kills
unreachable code as far as I can say. I can't tell what was the author
trying to do with the following check. First we have:
PNMI_STATIC const SK_PNMI_STATADDR
StatAddr[SK_PNMI_MAX_IDX][SK_PNMI_MAC_TYPES];
and then a check goes like this:
if (SK_PNMI_MAX_IDX !=
(sizeof(StatAddr) / (sizeof(SK_PNMI_STATADDR) * SK_PNMI_MAC_TYPES)))
with the second line being just ARRAY_SIZE(StatAddr), which will always
return SK_PNMI_MAX_IDX, rendering the check useless.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using ARRAY_SIZE() on arrays of the form array[][K] makes it unnecessary
to know the value of K when checking its size.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move wlan_postpone_association_work() and wlan_cancel_association_work()
from a assoc.h file to the sole user, into wext.c.
Renamed those two functions to to libertas_XXX as well.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable interrupts in the iwl4965 before calling request_irq() for
the case that the previous OS or the BIOS left a pending interrupt in
the chip. This behavior has been observed on some laptops such as T61
Thinkpads and Toshiba Portege R500
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When there are 2 linked structures, using a temporary variable to hold a pointer
to the often used structure usually produces better code (smaller and faster)
since compiler does not have to constantly re-fetch data from the first structure.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bring scan result handling more in line with drivers like ipw. Scan
results are aggregated and a BSS dropped after 15 seconds if no beacon
is received. This allows the driver to interact better with userspace
where more than one process may request scans or results at any time.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a consistent naming scheme for the ops.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the limits provided by mac80211.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put all access to wl->current_dev under protection of the mutex.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need the set_key callback, as we don't do hw crypto.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement much easier and more lightweight locking for
the periodic work. This also removes the last big busywait
loop and replaces it by a sleeping loop.
This patch for b43legacy is patterned aftar the same patch
for b43 by Michael Buesch <mb@bu3sch.de>.
Signed-off-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the direct call to rfkill on an rfkill event
and replaces it with an input device. This way userspace is also
notified about the event.
This patch is the port to b43legacy of a patch for b43 by Michael Buesch
<mb@bu3sch.de>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds full support for the RFKILL button and the RFKILL LED trigger.
This is a port to b43legacy of a patch by Michael Buesch <mb@bu3sch.de>
for b43.
Signed-off-by: Larry Finger<Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drive the LEDs through the generic LED triggers.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to b43legacy.
Signed-off-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the iwl3945 & iwl4965 drivers share some common Kconfig
symbols. This split it up into options for the individual drivers
and gets rid of all the CONFIG_IWLWIFI cruft.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwl3945 and iwl4965 devices share some common structure, but with a
lot of difference split all over. Currently the two drivers share a lot
of headers and use ugly preprocessor magic to manage the difference.
This patch keeps two entirely separate copies of the headers to get rid
of these hacks an ease future development.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mark more functions/variables static
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch do the following 2 things:
1. Make sure we don't add rate 60M part of supported rate in proble request,
some AP does not like that.
2. It is wrong to set priv->active_rate in this function, this will set
it to all avialable rates which might overwrite the mode supported rate.
priv->active_rate should be set by only from iwl_set_rate.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patche shortens the name of struct fw_image_desc to be struct
fw_desc.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds SCD registers for 5965
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves 3945 SCD registers to iwl-prph.h. These registers
are assigned from the periphery bus
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves 4965 SCD registers to iwl-prph.h. These registers
are assigned from the periphery bus
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces wording 'restricted' with more appropriate 'nic access'
NIC access is grabbed to prevent NIC entering power save mode
General cleanup of iwl-io.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames restricted_mem suffix with more proper
name targ_mem for function accessing memory on the nic in target mode
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames restricted_reg suffix with more proper
name prhp for function accessing registers on the periphery bus.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver drops any Rx frame larger than 2332 bytes, but with A-MSDU
frame, it could be up to 4K. This patch makes sure we can process larger
A-MSDU frame.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCI_DEVICE macro is more concise when using defualt values
in device definitions
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cck_power_index_compensation variable was never used
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These pieces of code appear to be useless. The BUG_ON is also performed in
iwl_send_cmd_async.
Serious karma would be needed to enter iwl_ativate_qos with a null priv.
I had a deja vu when patching this, but for the life of me I couldn't track
down a similar patch.
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moving code around, lindent, and whatnot created several places where
there appeared to be an 75 column "rule" instead of 80. This patch removes
those that I can spot, hopefully increasing readability.
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch shorten two comments lines in iwl-3945.c
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch remove cck_flag from iwl_driver_hw_info, this flag
is unused after spliting the iwl-base.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds TGN flag to QoS parameters. This flag governs enablement of
NAV shortening with CF-End and filters in 4 or 8K RX AMSDU packets
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up style of 'return' of rate scale 4965 functions.
It renames return name variables rc to ret, change functions to void if no
meaningful value was returned it add return of -EINVAL for checks of wrong
arguments.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames queue pointers to write_ptr and read_ptr
instead of first_empty and last_used. This is closer to technical
terminology we everyday use
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct the spelling of aqcuire.
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixing various spelling errors and typos. Mostly in comments. In total
27 words were corrected, some of which occurred more than ones.
Signed-Of-By: Ian Schram <ischram@telenet.be>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds erp_ie_changed handler to iwl4956
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Version bump.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a flag to struct txdata_entry_desc that specifies whether an ack for the
frame is to be expected. Use this flag to set the ACK bit in the tx descriptor.
Previously, the ACK bit could be set incorrectly on CTS-to-self frames, so they
caused retries and were reported to be failed in the txdone handlers.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a buffer, csr_cache which is used to hold copies of data being passed
to the USB stack which can get corrupted if multiple threads attempt to access
CSR registers simultaneously. There is also the possibility if multiple
threads try to access BBP or RF registers for the multiple USB operations
needed to get interleaved leading to incorrect results. This patch introduces
a mutex to prevent such simultaneous access. The interleaved access problem
may also affect the PCI devices but if so that will be handled in a follow-up
patch.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coverty indicated that data_desc with a single
element array is bad coding style. This removes
the structure and forces everybody to use __le32.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes rt73 antenna selection to what I believe is the correct way.
It also fixes a small selection bug that switched the antennas by accident.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the updated antenna setup the following
variables are no longer used.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes rt61 antenna selection again. It helps at least with the
rt61 pci card in my box, I hope I haven't broken behaviour on other RF chips.
RF 2529 antenna setup is incomplete, we need to at code for diversity when we
figure out how it is done properly.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some register accesses need rt2x00dev to be non-const
they all need modifying so the prototype is consistent.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When registering rfkill, make sure a initial
poll event is directly executed to detect the initial
rfkill state and send the event to the rfkill layer.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
input-polldev requires a correctly allocated
and initialized input device to be set for the
input_polled_dev->input field.
Failure to do that will prevent correct polling
of the device.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on investigation of the legacy drivers, I have made the
following assumptions of the antenna setup:
- R77 is the TX antenna configuration
- RF2529 fetches default antenna selection from NIC eeprom word
With these assumptions we can change the antenna configuration
to correctly read both antenna setup values and correctly
configure the antenna. And we can now also configure the antenna
for RF2529 without a double antenna.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antenna switching will be ignored when RX is enabled
during the switch. Make sure we disable the RX during
the switch and don't forget to reenable it later.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version bump.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the config() handler, make sure that we do configure an antenna if the
current active antenna is uninitialized. Furthermore, don't overwrite the
active antenna with bogus values if we didn't touch the antenna setup.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup if-statements for simple 1/0 register field values.
This also fixes a endian bug in rt2500usb when working
with the PHY_CSR2 initialization. As well as a bug
in the enabling of the LED in rt73usb.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mac80211 indicates that the default antenna setup
should be used _and_ that this default setup is SW_DIVERSITY.
This requires sampling and storing the RSSI per antenna
and check once every 2 seconds to determine if the RSSI
has changed significantly. Once this is the case we should sample
the other antenna for a short period and evaluate if
we need to swap antenna or not.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt2x00_clear_link() was becoming too large for statically inline,
also it was used on a single location and shouldn't really be
used anywhere else. So move the entire code into the function
rt2x00lib_start_link_tuner()
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although ANTENNA_SW_DIVERSITY should never be send
to the driver, we should still handle it to prevent bugs.
But instead of defaulting to ANTENNA_HW_DIVERSITY we
should default to ANTENNA_B instead.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211 has 3 values for the antenna setup:
0 - default
1 - use antenna 1
2 - use antenna 2
This means that rt2x00 should store the default value
from the EEPROM somwhere and use that when mac80211 indicates
that the antenna setup is 0.
This also implies that rt2x00 should no longer write the
hw->config.antenna_sel_* values based on the EEPROM input.
This also adds the basis in rt2x00lib for correct software
diversity handling. By default rt2x00lib will now configure
antenna B instead of hardware diversity.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the default EEPROM values use
the values from the enums instead of "magic" values.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all link quality statistics variables into
the link_qual structure. This cleans up the link
structure and allows us to use it for more then
just statistics.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the scheduled removal of the shaper driver.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the version number to 3.87.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does three things. It modifies tg3_setup_flow_control() to
use the administrator requested flow control settings if
autonegotiation is turned off. It slightly modifies the
tg3_setup_fiber_mii_phy() function to account for this new use case.
And finally, it does the same for tg3_setup_copper_phy().
The copper modifications are more than a small multi-line change. The
new code makes an attempt to avoid a link renegotiation if the link is
active at half duplex and the only difference between the current
advertised settings and requested advertised settings is the
flow control advertisements.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the software autoneg code to use the administrator
specified flow control parameters. Since the autonegotiation code uses
alternative flow control enumerations, the 1000-BaseX utility functions
are used and code was added to convert the definitions to and from the
alternate enumerations.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the 5704S hardware autoneg code to use the
administrator specified flow control parameters. Since the 5704S uses
device specific flow control enumerations, the 1000-BaseX utility
functions are used and code was added to convert the definitions to and
from the proprietary enumerations.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces magic values with preprocessor definitions for
the sg_dig_ctrl and sg_dig_status registers. This is preparatory work
for the next patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two functions designed to convert abstract TX & RX
flow control parameters to 1000-BaseT and 1000-BaseX autonegotiation
advertisements. Code that uses standard definitions which statically
advertises TX & RX flow control has been replaced with code that
configures the advertisements based on administrator dictated
preferences.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two new utility functions to resolve flow control. One
function resolves flow control based on 1000-BaseT register definitions.
The other resolves flow control based on 1000-Base X register
definitions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the TX and RX flow control flags from tg3_flags and
adds two new flow control variables, flowctrl and active_flowctrl.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move some code out of rc80211_simple since it's probably needed for all rate
selection algorithms, and fix iwlwifi accordingly. While at it, clean up the
rate_control_get_rate() interface.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These drivers pass full mactime information to the stack, make them
indicate this via the new RX_FLAG_TSFT to get mac80211 to show this
information in monitor mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce scan capabilities to WEXT so that userspace can do intelligent
things with scan behavior such as handling hidden SSIDs more gracefully.
If the driver reports a specific scan capability, the driver must
respect the options specified in the iw_scan_req structure when handling
the SIOCSIWSCAN call, unless it's mode or state does not allow it to do
so, in which case it must return an error.
This version switches to Dave Kilroy's suggestion of claiming unused
padding space for the scan_capa field.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPP synchronous tty channel driver: convert the semaphore dead_sem to a
completion
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change bnx2_init_napi() to void.
Warning was noted by DaveM.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable new tx ring and add new MSIX handler and NAPI poll function
for the new tx ring. Enable MSIX when the hardware supports it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To separate TX IRQs into a different MSIX vector, we need to
support a new tx ring. The original tx ring will still be used
when not using MSIX.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change bnx2_napi struct into an array and add code to manage multiple
IRQs. MSIX hardware structures and new registers are also added.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx related fields used in NAPI polling are moved from the main
bnx2 struct to the bnx2_napi struct.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx related fields used in NAPI polling are moved from the main
bnx2 struct to the bnx2_napi struct.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a bnx2_napi structure that will hold a napi_struct and
other fields to handle NAPI polling for the napi_struct. Various tx
and rx indexes and status block pointers will be moved from the main
bnx2 structure to this bnx2_napi structure.
Most NAPI path functions are modified to be passed this bnx2_napi
struct pointer.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a table to keep track of multiple IRQs and restructure the IRQ
request and free functions so that they can be easily expanded to
handle multiple IRQs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the code cleaner and easier to support different tx rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the MTU requires more than 1 page for the SKB, enable the page ring
and calculate the size of the page ring. This will guarantee order-0
allocation regardless of the MTU size.
Fixup loopback test packet size so that we don't deal with the pages
during loopback test.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function to reuse a page in case of allocation or other errors.
Add code to construct the completed SKB with the additional data in
the pages.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new fields to keep track of the pages and the page rings.
Add functions to allocate and free pages.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the common functions that will be used to initialize the
normal RX rings and the page rings.
Change the copybreak constant RX_COPY_THRESH to 128. This same
constant will be used for the max. size of the linear SKB when pages
are used. Copybreak will be turned off when pages are used.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function to handle new SKB allocation and to prepare the
completed SKB. This makes it easier to add support for non-linear
SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the various ring constants to make the code cleaner.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LOOPBACK_OVERHEAD is not used in this file at all.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
X86_32 was the last user of the FASTCALL macro, now that it
uses regparm(3) by default, this macro expands to nothing.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Schedule bcm43xx for for removal in the 2.6.26 development window.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use iov_length() instead of tun's homemade iov_total().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Cahill