Some channel indices of the low 5GHz band clash with
those of the 2.4GHz band. Therefore we should go
with the channel's center frequency.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Case assert is violated should be quite unlikely.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writing beacon to device happen through multiple write command calls.
zd_usb_iowrite16v uses synchronous urb call and with multiple write
commands in row causes high CPU usage.
Make asynchronous zd_usb_iowrite16v_async available outside zd_usb.c
and use where possible.
This lower CPU usage from ~10% to ~2% on Intel Atom when running
AP-mode with 100 TU beacon interval.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writing beacon to device happen through multiple write command calls.
zd_usb_iowrite16v uses synchronous urb call and with multiple write
commands in row causes high CPU usage.
This patch makes zd_usb_iowrite16v use asynchronous urb submit within
zd_usb.c. zd_usb_iowrite16v_async_start is used to initiate writing
multiple commands to device using zd_usb_iowrite16v_async. Each URB
is delayed and submitted to device by next zd_usb_iowrite16v_async
call or by call to zd_usb_iowrite16v_async_end. URBs submitted by
zd_usb_iowrite16v_async have URB_NO_INTERRUPT set and last URB
send by zd_usb_iowrite16v_async_end does not. This lower CPU
usage when doing writes that require multiple URBs.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211rw is using usb_bulk_msg() with usb_sndbulkpipe() on interrupt endpoint.
However usb_bulk_msg() internally corrects this and makes interrupt URB.
It's better to change usb_bulk_msgs in zd1211rw to usb_interrupt_msg for less
confusion.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beaconing should be disabled before stopping beacon queue.
Not doing so could queue up beacons in hw that causes
failure to stop Tx DMA, due to pending frames in hw
and also unnecessary beacon tasklet schedule.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 739fd94 ("rt2x00: Pad beacon to multiple of 32 bits")
added calls to skb_pad() without checking the return value,
which could cause problems if any of those calls does happen
to fail. Add checks to prevent this from happening.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the phy.c codes for rtl8192ce and rtl8192cu be as alike as possible.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make rtlwifi/rtl8192ce/fw.{h,c} match what will be needed for
rtlwifi/rtl8192cu.{h,c}.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To reuse as much code as possible when adding additional drivers to the
rtlwifi tree, the common parts of various routines are moved to
drivers/net/wireless/rtlwifi. This patch does that for the version of
dm.{h,c} used by rtl8192ce.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rtlwifi core needs some changes before inclusion of a driver
for the RTL8192CU USB device.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: <chaoming_li@realsil.com.cn>
Signed-off-by: <george0505@realtek.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Combo devices have TX statistics on different place, because
struct statistics_rx_bt and struct statistics_rx have different
size. User proper values on combo devices instead of random data.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make ack health code easies to read. Compared to previous
code, we do not print debug messages when expected_ack_cnt_delta == 0
and also do check against negative deltas.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No functional change, make recover from statistics code
easies to read.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variable appears in both ath_softc and ath_beacon_config.
The struct ath_beacon_config is embedded in ath_softc. The redundant
variable was added by commit id 57c4d7b4c4.
Signed-off-by: Steve Brown <sbrown@cortland.com>
Reviewed-by: Mohammed Shafi <shafi.ath9k@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=654599
Many users report very low speed problem on 3945 devices,
this patch fixes problem, but only for some of them.
For unknown reason, sometimes after hw scanning, device is not able
to receive frames at high rate. Since plcp health check may request
hw scan to "reset radio", performance problem start to be observable
after update kernel to .35, where plcp check was introduced.
Bug reporter confirmed that removing plcp check fixed problem for him.
Reported-and-tested-by: SilvioTO <silviotoya@yahoo.it>
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of looking for supported_rates change on every tx packet,
just extract the supported_rates after association completes (station only).
Remove wl1271.sta_rate_set and WL1271_FLAG_STA_RATES_CHANGED which are
not used anymore.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
make the configuration management more flexible by using the
conf struct, rather than predefined macros.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This patch adds support for the new wl12xx firmware (Rev 6.1.3.50.49)
Since this fw is not backward compatible with previous fw versions,
a new fw (with different name) is being fetched.
(the patch is big because it contains all the required fw api changes.
splitting it into multiple patches will result in corrupted intermediate
commits)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
mcp2.5 uses this acx to configure the fw only once, rather than
passing the params in every enter psm command.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add few comments for not parsing DTIM period from mac80211
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fast channel change fixes:
a) Always set OFDM timings
b) Don't re-activate PHY
c) Enable only NF calibration, not AGC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With commit 554d1d027b only one RF_KILL
interrupt will be seen by the driver when the interface is down.
Re-enable the interrupt when it occurs to see all transitions.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code, and the places that set the variable
is_internal_short_scan and the vif pointers are
all protected by the mutex, there's no point in
locking the spinlock here as well (any more).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since even with the latest changes the false positive issue of the baseband
hang check is not fully solved yet, additional checks are needed.
If the baseband hang occurs, the rx_clear signal will be stuck to high, so
we can use the cycle counters to confirm it.
With this patch, a hardware reset is only triggered if the baseband hang
check returned true three times in a row, with a beacon interval between
each check and if the busy time was also 99% or more during the check
intervals.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All register writes to the key cache have to be done in pairs. However,
the clearing of a separate MIC entry with hardware revisions that use
combined MIC key layout did not do that with one of the registers. Add
the matching register write to the following register to make the KEY4
register write actually complete.
This is mostly a fix for a theoretical issue since the incorrect entry
that could potentially be left behind in the key cache would not match
with received frames. Anyway, better make this code clean the entry
correctly using paired register writes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It should be safe to enable AP-mode now.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX appears to freeze while idle. Resetting rx-urbs appears to be enough to fix
this. Do reset 30 seconds after last rx.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When driver fails to acquire device semaphore lock, device usually
freezes soon afterwards. So failing to acquire lock indicates us that
not everything is going right in device/fw. So reset device when
this happens.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing transfers at high speed for long time, tx queue can freeze. So add
tx watchdog. TX-watchdog checks for locked tx-urbs and reset hardware when
such is detected. Merely unlinking urb was not enough, device have to be
reseted. Hw settings are restored so that any open link will stay on after
reset.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need HW hard reset later in patchset to reset device after TX-stall.
Collect all settings that we have set to driver for later reset and
add restore function.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Device command timeouts are set up very high (1 sec) and this causes
AP beacon to lock up for long for example. Checking timeouts on device
it's easy to see that 1 sec timeout is not needed, when device fails
to response longer timeout doesn't help:
[ 473.074419] zd1211rw 1-1:1.0: print_times() Read times:
[ 473.175163] zd1211rw 1-1:1.0: print_time() 0 - 10 msec: 1506
[ 473.176429] zd1211rw 1-1:1.0: print_time() 11 - 50 msec: 0
[ 473.177955] zd1211rw 1-1:1.0: print_time() 51 - 100 msec: 0
[ 473.180703] zd1211rw 1-1:1.0: print_time() 101 - 250 msec: 0
[ 473.182101] zd1211rw 1-1:1.0: print_time() 251 - 500 msec: 0
[ 473.183221] zd1211rw 1-1:1.0: print_time() 500 - 1000 msec: 20
[ 473.184381] zd1211rw 1-1:1.0: print_time() 1000 - ... msec: 18
Also vendor driver doesn't use this long timeout. Therefore change
timeout to 50msec.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As might lower beacon update CPU usage.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use stack for allocing small < 64 byte arrays in zd_chip.c and preallocated
buffer in zd_usb.c. This might lower CPU usage for beacon setup.
v2:
- Do not use stack buffers in zd_usb.c as they would be used for urb
transfer_buffer.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon config function writes beacon to hw one write per byte. This is very
slow (usually taking more than 100ms to finish) and causes high CPU usage
when in AP-mode (kworker at ~50% on Intel Atom N270). By batching commands
together zd_mac_config_beacon() runtime can be lowered to 1/5th and lower
CPU usage to saner levels (<10% on Atom).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing tx/rx at high packet rate (for example simply using ping -f),
device starts to fail to respond to control messages. On non-AP modes
this only causes problems for LED updating code but when we are running
in AP-mode we are writing new beacon to HW usually every 100ms. Now if
control message fails in HW beacon setup, device lock is kept locked
and beacon data partially written. This can and usually does cause:
1. HW beacon setup fail now on, as driver cannot acquire device lock.
2. Beacon-done interrupt stop working as device has incomplete beacon.
Therefore make zd_mac_config_beacon() always try to release device lock
and add beacon watchdog to restart beaconing when stall is detected.
Also fix zd_mac_config_beacon() try acquiring device lock for max 500ms,
as what old code appeared to be trying to do using loop and msleep(1).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for AP-mode beacon. Also disable beacon when interface is set
down as otherwise hw will keep flooding NEXT_BCN interrupts.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For reasons not very clear yet to me, filter_ack leaves matching tx-packet
pending with 'ack_pending'. This causes tx-packet to be passed back to upper
layer after next packet has been transfered and tx-packets might end up
coming come out of monitor interface in wrong order vs. rx.
Because of this when enable AP-mode, hostapd monitor interface would get
packets in wrong order causing problems in WPA association.
So don't use mac->ack_pending when in AP-mode.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As bss_info_changed may sleep, we can as well set RTS_CTS register right away.
Keep mac->short_preamble for later use (hw reset).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Workers not needed anymore since configure_filter may sleep. Keep
mac->multicast_hash for later use (hw reset).
Signed-off-by: Jussi Kivilinna <jussi.kivilina@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vendor driver uses CR_BNC_INTERVAL at various places, one is HW_EnableBeacon()
that combinies beacon interval with BSS-type flag and DTIM value in upper 16bit
of u32. The other one is HW_UpdateBcnInterval() that set_aw_pt_bi()
appears to be based on. HW_UpdateBcnInterval() takes interval argument as u16
and uses that for calculations, set_aw_pt_bi() uses u32 value that has flags
and dtim in upper part. This clearly seems wrong. Also HW_UpdateBcnInterval()
updates only lower 16bit part of CR_BNC_INTERVAL. So make set_aw_pt_bi() do
calculations on only lower u16 part of s->beacon_interval.
Also set 32bit beacon interval register before reading values from device,
as HW_EnableBeacon() on vendor driver does. This is required to make beacon
work on AP-mode, simply reading and then writing updated values is not enough
at least with zd1211b.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
OOPS if worker is running and disconnect() is called (triggered
by unpluging device). Much harder to trigger at this stage but
later when we have AP beacon work in process_intr it happens very
easy.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When stress testing AP-mode I hit OOPS when unpluging or rmmodding
driver.
It appears that when tx-queue is disabled, tx-urbs might be left pending.
These can cause ehci to call non-existing tx_urb_complete() (after rmmod)
or uninitialized/reseted private structure (after disconnect()). Add skb
queue for submitted packets and unlink pending urbs on zd_usb_disable_tx().
Part of the problem seems to be usb->free_urb_list that isn't always
working as it should, causing machine freeze when trying to free the list
in zd_usb_disable_tx(). Caching free urbs isn't what other drivers seem
to be doing (usbnet for example) so strip free_usb_list.
Patch makes tx-urb handling saner with use of urb anchors.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a off-by-one bug which bugged
the driver's PS-POLL capability.
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The below patch fixes a typo comamnd to command.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beaconing vif addition is based on max beacon slot
available. So it is better to reserve a beacon slot
on interface addition and let it be configured properly
on bss_info change.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The opmode recalculation is accessing hw registers.
When it is called from remove interface callback and
if there are no vifs present then hw is moved to FULL SLEEP
by radio disable. So use power save wrappers before
accessing hw registers in calculating opmode state.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
move ath_update_txpow to common to remove code duplication
in both ath9k & ath9k_htc.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ani work is cancelled in dissaoctiation. But in some cases
during suspend, deauthention never be called. So we failed
to stop ani work which was identified by the following
warning.
Call Trace:
[<ffffffffa0454a1d>] ieee80211_can_queue_work.clone.17+0x2d/0x40 [mac80211]
[<ffffffffa0454a60>] ieee80211_queue_delayed_work+0x30/0x60 [mac80211]
[<ffffffffa0567f82>] ath9k_ani_work+0x142/0x250 [ath9k_htc]
[<ffffffff81073c70>] async_run_entry_fn+0x0/0x180
[<ffffffffa0567e40>] ath9k_ani_work+0x0/0x250 [ath9k_htc]
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the rate index rate_idx and preamble flag RX_FLAG_SHORTPRE on received
packets.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable adhoc support in wl1251 driver.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement connection quality monitoring similar to the wl1271 driver.
It triggers ieee80211_cqm_rssi_notify with the corresponding event when
RSSI drops blow RSSI threshold or rises again above the RSSI threshold.
It should be noted that wl1251 doesn't support RSSI hysteresis, instead it
uses RSSI averageing and delays events until a certain count of frames
proved RSSI change.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port the beacon early termination feature from wl1251 driver version
included in the Maemo Fremantle kernel.
It is enabled when going to power-saving mode and disabled when leaving
power-saving mode.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements TX buffer alignment for cloned or too small skb by
copying and replacing the original skb.
Recent changes in wireless-testing seems to make this really necessary.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue stopping/waking functionality was broken in a way that could
cause the TX to stall if the right circumstances are met.
The problem was caused by tx_work, which is scheduled on each TX operation.
If the firmware buffer is full, tx_work does nothing. In combinition with
stopped queues or non-continues transfers, tx_work is never scheduled again.
Moreover the low watermark introduced by
9df86e2e70 never takes effect because of some
old code.
Solve this by scheduling tx_work every time tx_queue is non-empty and
firmware buffer is freed on tx_complete.
This also solves a possible but unlikely case: If less frames than the high
watermark are queued, but more than firmware buffer can hold. This results
in queues staying awake but the only scheduled tx_work doesn't transfer all
frames, so the remaining frames are stuck in the queue until more frames
get queued and tx_work is scheduled again.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To support suspend/resume in if_spi we need two things:
- re-setup fw in lbs_resume(), because if_spi powercycles card;
- don't touch hwaddr on second lbs_update_hw_spec() call for same
reason;
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use workqueue to perform SPI xfers, it's necessary to fix
nasty "BUG: scheduling while atomic", because
spu_write() calls spi_sync() and spi_sync() may sleep, but
hw_host_to_card() callback can be called from atomic context.
Remove kthread completely, workqueue now does its job.
Restore intermediate buffers which were removed in commit
86c34fe89e that introduced
mentioned bug.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In drivers/net/wireless/wl1251/main.c:wl1251_op_bss_info_changed() we make
a call to ieee80211_beacon_get() which may return NULL, but we do not
check the return value before dereferencing the pointer.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
6250 2x2 devices have 2 tx chain and 2 rx chain. For some reason,
the EEPROM contain incorrect information and indicate it only has single
tx chain. overwrite it with .cfg parameter to make sure both chain 'A' and
chain 'B' can be used for transmit and receive
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
free the skb's when the Tx of PAPRD frames fails and also add a debug
message indicating that.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During the period of BT coex changes, REPLY_BT_COEX_SCO host command
is no longer needed to support SCO/eSCO type of traffic. delete it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The beacon notification changed between 4965 and
agn because the embedded TX response changed, but
iwlwifi was never updated to know about this.
Update it now so the IBSS manager status will be
tracked correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Use the values from the peer to set up the ucode
for the right maximum number of subframes in an
aggregate. Since the ucode only tracks this per
station, use the minimum across all aggregation
sessions with this peer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Allow peers to size their reorder buffer more
accurately by advertising that we'll never send
aggregates longer than the default (31).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In order to support RSN IBSS, we need to
(ok actually maybe it's just easiest to)
disable group key programming so that any
group-addressed frames will be decrypted
in software which handles the per-station
keys for this easily. We could keep the
encryption in the device, but that takes
more work and seems unnecessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The I/Q swapping is extremely important and should be dealt with extra care.
It will affects OFDM and CCK differently.
For 6000/6005/6030 series devices, the I/Q were swapped, and for 2000 series
devices, it is in non-swapped status (but its swapped with respected to 6000/6005/6030).
so the CSR_GP_DRIVER_REG_BIT_RADIO_IQ_INVER register need to be set to support
the correct behavior.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Driver check alive message from ucode, if it is not ok, then need
to restart the loading process. instead of checking multiple places
for failure, only need to check in once place when receive alive
message from uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Commit 0b01f030d3 added a new argument
to the ampdu_action operation. The ampdu_action operation in the
wl12xx driver currently doesn't have that argument and this generates
a warning. This happened during merging of the latest mac80211
patches with the wl12xx BA patches.
CC [M] drivers/net/wireless/wl12xx/main.o
drivers/net/wireless/wl12xx/main.c:3035: warning: initialization from incompatible pointer type
The wl12xx driver doesn't need to do anything about the buf_size
argument since the AMPDU TX is fully handled by the firmware.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After commit 59eb21a650
"cfg80211: Extend channel to frequency mapping for 802.11j"
we use uninitialized sband->band when assign channel frequencies, what
results that 5GHz channels have erroneous (zero) center_freq value.
Patch fixes problem and simplifies code a bit.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX/RX work structures must be able to run independently
of other workqueues. This is because mac80211 might use
the flush() callback function from various context, which depends
on the TX/RX work to complete while the main thread is blocked
(until the the TX queues are empty).
This should reduce the number of 'Queue %d failed to flush' warnings.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During device removal all pending work and tasklets must
be guaranteed to be halted. So far only the txstatus_tasklet
was killed.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both rt61pci and rt73usb check the Michael MIC in hardware and strip the
Michael MIC from received frames. This is perfectly allowed by mac80211 as
long as this is properly reported to mac80211.
Both these drivers reported the Michael MIC handling properly to mac80211, but
still contained a FIXME comment on this, which is not needed to be handled, since
mac80211 doesn't really need the Michael MIC in this case.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the specific mac field of the wcid_entry structure to copy the MAC
address to, instead of just overwriting the structure.
Previous code resulted in the same, but this form is cleaner.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported and found by Johannes Stezenbach:
rt2800{pci,usb} do not report the Michael MIC in RXed frames, but do check
the Michael MIC in hardware. Therefore we have to report to mac80211 that the
received frame does not include the Michael MIC.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixing a trivial comment typo.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CLOCK CYCLE: Clock cycle count in 1us
PCI:0x21, PCIE:0x7d, USB:0x1e
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove STATE_RADIO_IRQ_OFF_ISR and STATE_RADIO_IRQ_ON_ISR as they are
not used anymore.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No driver uses interrupt threads anymore. Remove the remaining interrupt
thread artifacts.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix interrupt processing on slow machines by using individual tasklets
for each different device interrupt. This ensures that while a RX or TX
status tasklet is scheduled only the according device interrupt is
masked and other interrupts such as TBTT can still be processed.
Also, this allows us to use tasklet_hi_schedule for TBTT processing
which is required to not send out beacons with a wrong DTIM count (due
to delayed periodic beacon updates). Furthermore, this improves the
latency between the TBTT and sending out buffered multi- and broadcast
traffic.
As a nice bonus, the interrupt handling overhead should be much lower.
Compile-tested only.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix interrupt processing on slow machines by using individual tasklets
for each different device interrupt. This ensures that while a RX or TX
status tasklet is scheduled only the according device interrupt is
masked and other interrupts such as TBTT can still be processed.
Also, this allows us to use tasklet_hi_schedule for TBTT processing
which is required to not send out beacons with a wrong DTIM count (due
to delayed periodic beacon updates). Furthermore, this improves the
latency between the TBTT and sending out buffered multi- and broadcast
traffic.
As a nice bonus, the interrupt handling overhead should be much lower.
Compile-tested only.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix interrupt processing on slow machines by using individual tasklets
for each different device interrupt. This ensures that while a RX or TX
status tasklet is scheduled only the according device interrupt is
masked and other interrupts such as TBTT can still be processed.
Also, this allows us to use tasklet_hi_schedule for TBTT processing
which is required to not send out beacons with a wrong DTIM count (due
to delayed periodic beacon updates). Furthermore, this improves the
latency between the TBTT and sending out buffered multi- and broadcast
traffic.
As a nice bonus, the interrupt handling overhead should be much lower.
Compile-tested only.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix interrupt processing on slow machines by using individual tasklets
for each different device interrupt. This ensures that while a RX or TX
status tasklet is scheduled only the according device interrupt is
masked and other interrupts such as TBTT can still be processed.
Also, this allows us to use tasklet_hi_schedule for TBTT and PRETBTT
processing which is required to not send out beacons with a wrong DTIM
count (due to delayed periodic beacon updates). Furthermore, this
improves the latency between the TBTT and sending out buffered multi-
and broadcast traffic.
As a nice bonus, the interrupt handling overhead is reduced such that
rt2800pci gains around 25% more throuhput on a rt3052 MIPS board.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable the txstatus tasklet when interrupts are enabled and disable it
together with the interrupts. Also make the txstatus tasklet useful even
without the tx status FIFO and make use of the generic rt2x00 tasklet
initialization macro.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No functional changes, just preparation for moving interrupt handling to
tasklets. The tasklets are disabled by default. Drivers making use of
them need to enable the tasklets when the device state is set to IRQ_ON.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow the beacondone and pretbtt functions to update the beacon from
atomic context by using the beacon update functions with caller locking.
This is a preparation for moving the periodic beacon handling into
tasklets that require atomic context.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently there are two places that trigger a beacon update on PCI
devices. The bss_info_changed callback and the periodic update
triggered by the TBTT or PRETBTT interrupt.
Since the next TBTT or PRETBTT interrupt will periodically fetch an
updated beacon remove the update_beacon call in the bss_info_changed
callback for PCI devices.
In the worst case it will take one beacon interval longer to fetch
the new beacon then before. For devices that have a PRETBTT interrupt
there should be no change at all.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a beacon_update_locked function that does not acquire the
according beacon mutex to allow beacon updates from atomic context. The
caller has to take care of synchronization.
No functional changes. Just preparation for beacon updates from tasklet
context.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows to dynamically remove beaconing interfaces without
shutting beaconing down on all interfaces.
The only place to start and stop beaconing are now the start- and
stop_queue callbacks. Hence, we can remove some register writes during
interface bring up (config_intf) and only write the correct sync mode
to the register there.
When multiple beaconing interfaces are present we should enable
beaconing as soon as mac80211 enables beaconing on at least one of
them. The beacon queue gets stopped when the last beaconing
interface was stopped by mac80211. Therefore, introduce another
interface counter to keep track ot the number of enabled beaconing
interfaces and start or stop the beacon queue accordingly.
To allow single interfaces to stop beaconing, add a new driver
callback clear_beacon to clear a single interface's beacon without
affecting the other interfaces. Don't overload the clear_entry callback
for clearing beacons as that would introduce additional overhead
(check for each TX queue) into the clear_entry callback which is used
on the drivers TX/RX hotpaths.
Furthermore, the write beacon callback doesn't need to enable beaconing
anymore but since beaconing should be disabled while a new beacon is
written or cleared we still disable beacon generation and enable it
afterwards again in the driver specific callbacks. However, beacon
related interrupts should not be disabled/enabled here, that's solely
done from the start- and stop queue callbacks. It would be nice to stop
the beacon queue just before the beacon update and enable it afterwards
in rt2x00queue itself instead of the current implementation that relies
on the driver doing the right thing. However, since start- and
stop_queue are mutex protected we cannot use them for atomic beacon
updates.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only use IWL_RATE_COUNT_3945 in 3945 code.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When DEBUG_SPI is included in the debug log level wl1271_spi_reset()
will dump the already freed memory instead of the SPI buffer.
This bug was spotted by the semantic patch tool coccinelle using the
script found at scripts/coccinelle/free/kfree.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
free the skb's when the Tx of PAPRD frames fails and also add a debug
message indicating that.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ath9k: fix tx queue index confusion in debugfs code" changed the debug
function but not the stub.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use priv->cfg->bt_params && priv->cfg->bt_params->bt_statistics
conditional in few places, merge it into one function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never set STATUS_SCANNING in softwre scanning mode, disable_hw_scan
check is unneeded. Correct debug message while at it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use priv->cfg->bt_params && priv->cfg->bt_params->advanced_bt_coexist
conditional in few places, merge it into one function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
struct iwl_queue is not part of firmware interface, so __packed is not
needed. Remove it since is may affect performance.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar change as we already do for agn, need to avoid
"Error setting Tx power (-5)" message when loading module.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mac80211 can request for tx power and channel change in one ->config
call. If that happens, *_send_tx_power functions will try to setup tx
power for old channel, what can be not correct because we already change
the band. I.e error "Failed to get channel info for channel 140 [0]",
can be printed frequently when operating in software scanning mode.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register definition for retry configuration on AR5212 was wrong, and simply
copied over from AR5210. Update the register definitions from the documentation.
Let the short and long retries be configured from mac80211 and use the standard
values of 7 and 4 by default. Also we need to make sure we don't export more
retries than we are configured for to mac80211 (and the rate module) in
hw->max_rate_tries.
Also clean up the code by removing unused defines and variables and drop the
different values for "station retries" - if these need to be different it can
be handled tru ah_retry_long/short.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change from the systems team to update PMU setting for AR9485
version of chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Spin_lock has been tried to be acquired twice from ath9k_tasklet
to ath_reset which resulted in a machine freeze.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Updates from the analog team for AR9485 chipsets to set
DDR_PLL2 and DDR_PLL3. Also program the BB_PLL ki
and kd value.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When this PLL hang issue is seen, both Rx and Tx fail to work.
The sqsum_dvc needs to be below 2000 for a good chip. During
this issue the sqsum_dvc value is beyond 80000 and only a
full reset can solve this problem.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a function to observe the delta VC of BB_PLL.
For a good chip, the sqsum_dvc is below 2000.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has separate filter masks for compressed/uncompressed
BlockAcks and BlockAckRequests. Add them.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this change, less CPU time is spent trying to look for consecutive
pages for rx skbs. This also reduces the socket memory required for IP/UDP
reassembly.
Only two buffers per frame are supported. Frames spanning more buffers
will be dropped, but the buffer size is enough to handle the required
AMSDU size.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_hw: move AR9280 PCI EEPROM fix to eeprom_def.c"
changed the behavior of INI overriding which is needed only
for PCI cards. Revert to the original check.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_hw: Relocate Opmode initialization"
moved the opmode initialization before the STA_ID1 register
was programmed with defaults. This changed the original
behaviour because the re-programming code doesn't take into
account the existing value in the register. Both ath9k and ath9k_htc
were not affected by this change because the opmode is
re-initialized after every reset, when RX is started.
Revert to the original behavior, except keep it outside the
REGWRITE block. This would help remove extraneous opmode calls
in the driver core.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that rx and tx dumps go through the tracing infrastructure,
we no longer need to keep these routines around.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a few tracepoints to ath5k driver transmit and
receive callbacks in order to record packet traffic.
We record the entire packet in the trace buffer so that
the data can be extracted with trace-cmd and external
plugins.
Compared to the previous debugging calls, this approach
removes an out-of-line function call from the tx and rx
paths in the compiled-in-but-disabled case, while
improving the ability to process the logged data.
A new option, CONFIG_ATH5K_TRACER, is added so that one
may disable the tracepoints completely.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE80211_WEP_NKID is not used in ath9k any more since the key handling code
has been moved to ath/.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables 4.9GHz frequencies in ath5k if they are allowed as indicated by
the regulatory domain code. Currently this is MKK9_MKKC (0xfe).
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a helper function to ath/regd.c which can be asked if 4.9GHz channels
are allowed for a given regulatory domain code. This keeps the knowledge of
regdomains and defines like MKK9_MKKC in one place. I'm passing the regdomain
code instead of the ath_regulatory structure because this needs to be called
quite early in the driver inititalization where ath_regulatory is not available
yet in ath5k.
I'm using MKK9_MKKC only because this is the regdomain in the 802.11j enabled
sample cards we got from our vendor. I found some hints in HAL code that this
is used by Atheros to indicate 4.9GHz channels support and that there might be
other domain codes as well, but as I don't have any documentation I'm just
putting in what I need right now. It can be extended later.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shorten some lines and make code more readable.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various places printing tx queue information used various different ways to
get a tx queue index for printing statistics. Most of these ways were wrong.
ATH_TXQ_AC_* cannot be used as an index for sc->tx.txq, because it is only
used internally for queue assignment.
One place used WME_AC_* as a queue index for sc->debug.stats.txstats, however
this array uses the ath9k_hw queue number as well.
Fix all of this by always using the ath9k_hw queue number as an index, and
always looking it up by going through sc->tx.txq_map.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It does not make much sense to keep the current virtual wiphy implementation
any longer - it adds significant complexity, has very few users and is still
very experimental. At some point in time, it will be replaced by a proper
implementation in mac80211.
By making the code easier to read and maintain, removing virtual wiphy support
helps with fixing the remaining driver issues and adding further improvements.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of spreading ath_wake_mac80211_queue() calls over multiple places
in the tx path that process the tx queue for completion, call it only
where the pending frames counter gets decremented, eliminating some
redundant checks.
To prevent queue draining from waking the queues prematurely (e.g. during
a hardware reset), reset the queue stop state when draining all queues,
as the caller in main.c will run ieee80211_wake_queues(hw) anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While unloading the driver, the ps_usecount is incremented
before configuring gpio registers in deinit_device.
But it is failed to restore the ps_usecount after that.
The problem is that the chip is forcibly moved to FULL SLEEP
by radio_disable when mac80211 is reporting as idle
though ps_usecount is not zero.
This patch retores ps_usecount properly and ensures that
the chip is always moved to full sleep only if ps usage
count is zero which also helps in debugging deadbeef on
multivif case. And also fixes the following warning.
ath: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:536
ath_stoprecv+0xf4/0x100 [ath9k]()
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bit 6 & 7 of AR_WA (0x4004) should be enabled only
for the chips that are supporting L0s functionality
while resuming back from S3/S4.
Enabling these bits for AR9280 is causing system hang
within a few S3/S4-resume cycles.
Cc: stable@kernel.org
Cc: Jack Lee <jlee@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Disable interrupts, kill tasklets
and then works in correct order.
Cc: stable@kernel.org
Tested-by: Sujith <m.sujith@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Moreover we enable interrupts
in tasklet function, so we could potentially end with interrupts
enabled when driver is not ready to receive them.
I think patch should fix Ben's kernel crash from:
http://marc.info/?l=linux-wireless&m=129438358921501&w=2
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath5k version of ieee80211_generic_frame_duration() returns
an __le16 for standard modes but a cpu-endian int for turbo/half/
quarter rates. Make it always return cpu-endian values.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Review spotted a problem with the error handling in ath5k_hw_dma_stop:
a successful return from ath5k_hw_stop_tx_dma will be treated as
an error, so we always bail out of the loop after processing a single
active queue. As a result, we may not actually stop some queues during
reset.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter