use put_unaligned_le16 for precedence value in mesh
channel switch support
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds generic cipher scheme support to mac80211, such schemes
are fully under control by the driver. On hw registration drivers
may specify additional HW ciphers with a scheme how these ciphers
have to be handled by mac80211 TX/RR. A cipher scheme specifies a
cipher suite value, a size of the security header to be added to
or stripped from frames and how the PN is to be verified on RX.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To report channel width correctly we have
to send correct channel parameters from
mac80211 when calling cfg80211_cac_event().
This is required in case of using channel width
higher than 20MHz and we have to set correct
dfs channel state after CAC (NL80211_DFS_AVAILABLE).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mesh STA receiving the mesh CSA action frame is not able to trigger
the mesh channel switch due to the incorrect handling and comparison
of mesh channel switch parameters element (MCSP)'s TTL. Make sure
the MCSP's TTL is updated accordingly before calling the
ieee80211_mesh_process_chnswitch. Also, we update the beacon before
forwarding the CSA action frame, so MCSP's precedence value and
initiator flag need to be updated prior to this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Setup chandef for radar event correctly, before we
will clear this in ieee80211_dfs_cac_cancel() function.
Without this patch mac80211 will report wrong channel
width in case we will get radar event during active CAC.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the triggering of CSA frame using mesh interface. The
rules are more or less same with IBSS, such as not allowed to
change between the band and channel width has to be same from
the previous mode. Also, move the ieee80211_send_action_csa
to a common space so that it can be re-used by mesh interface.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Process the CSA frame according to the procedures define in IEEE Std
802.11-2012 section 10.9.8.4.3 as follow:
* The mesh channel switch parameters element (MCSP) must be availabe.
* If the MCSP's TTL is 1, drop the frame but still process the CSA.
* If the MCSP's precedence value is less than or equal to the current
precedence value, drop the frame and do not process the CSA.
* The CSA frame is forwarded after TTL is decremented by 1 and the
initiator field is set to 0. Transmit restrict field and others
are maintained as is.
* No beacon or probe response frame are handled here.
Also, introduce the debug message used for mesh CSA purpose.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
6c17b77b67 ensures that a device's
mac80211 queues will remain stopped while offchannel. Since the
vif can no longer be offchannel when the queues wake it's not
necessary to check for this before waking its netdev queues.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver requests to move to STATIC or DYNAMIC SMPS,
we send an action frame to each associated station and
reconfigure the channel context / driver.
Of course, non-MIMO stations are ignored.
The beacon isn't updated. The association response will
include the original capabilities. Stations that associate
while in non-OFF SMPS mode will get an action frame right
after association to inform them about our current state.
Note that we wait until the end of the EAPOL. Sending an
action frame before the EAPOL is finished can be an issue
for a few clients. Clients aren't likely to send EAPOL
frames in MIMO anyway.
When the SMPS configuration gets more permissive (e.g.
STATIC -> OFF), we don't wake up stations that are asleep
We remember that they don't know about the change and send
the action frame when they wake up.
When the SMPS configuration gets more restrictive (e.g.
OFF -> STATIC), we set the TIM bit for every sleeping STA.
uAPSD stations might send MIMO until they poll the action
frame, but this is for a short period of time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix vht streams loop, initialisation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a frame's timestamp is calculated, and the bitrate
calculation goes wrong and returns zero, the system
will attempt to divide by zero and crash. Catch this
case and print the rate information that the driver
reported when this happens.
Cc: stable@vger.kernel.org
Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the default setting for WMM parameters outside the for loop
to avoid redundant assignment multiple times.
Signed-off-by: Fred Zhou <fred.zy@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The authentication frame has a fixied size of 30 bytes
(including header, algo num, trans seq num, and status)
followed by a variable challenge text.
Allocate using exact size, instead of over-allocation
by sizeof(ieee80211_mgmt).
Signed-off-by: Fred Zhou <fred.zy@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch "mac80211: select and adjust bitrates according to
channel mode" causes regression and breaks the extended supported rate
IE setting. Since "i" is starting with 8, so this is not necessary
to introduce "skip" here.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Reviewed-by: Jason Abele <jason@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel switch parsing function can be re-used for the IBSS code,
put the common part into an extra function.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[also move/rename chandef_downgrade]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If it is needed to disconnect multiple virtual interfaces after
(WoWLAN-) suspend, the most obvious approach would be to iterate
all interfaces by calling ieee80211_iterate_active_interfaces()
and then call ieee80211_resume_disconnect() for each one. This
is what the iwlmvm driver does.
Unfortunately, this causes a locking dependency from mac80211's
iflist_mtx to the key_mtx. This is problematic as the former is
intentionally never held while calling any driver operation to
allow drivers to iterate with their own locks held. The key_mtx
is held while installing a key into the driver though, so this
new lock dependency means drivers implementing the logic above
can no longer hold their own lock while iterating.
To fix this, add a new ieee80211_iterate_active_interfaces_rtnl()
function that iterates while the RTNL is already held. This is
true during suspend/resume, so that then the locking dependency
isn't introduced.
While at it, also refactor the various interface iterators and
keep only a single implementation called by the various cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to be able to (securely) keep connections alive after
the system was suspended for WoWLAN, we need some additional
APIs. We already have API (ieee80211_gtk_rekey_notify) to tell
wpa_supplicant about the new replay counter if GTK rekeying
was done by the device while the host was asleep, but that's
not sufficient.
If GTK rekeying wasn't done, we need to tell the host about
sequence counters for the GTK (and PTK regardless of rekeying)
that was used while asleep, add ieee80211_set_key_rx_seq() for
that.
If GTK rekeying was done, then we need to be able to disable
the old keys (with ieee80211_remove_key()) and allocate the
new GTK key(s) in mac80211 (with ieee80211_gtk_rekey_add()).
If protocol offload (e.g. ARP) is implemented, then also the
TX sequence counter for the PTK must be updated, using the new
ieee80211_set_key_tx_seq() function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There appear to be two regressions in ibss.c when calling
ieee80211_sta_def_wmm_params():
* the second argument should be a rate length, not a rate array. This
was introduced by my commit "mac80211: select and adjust bitrates
according to channel mode"
* the third argument is not initialized (anymore), making further
checks within this function useless.
Since ieee80211_sta_def_wmm_params() is only used by ibss anyway,
remove the function entirely and handle the operating mode decision
immediately.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The various components accessing the bitrates table must use consider
the used channel bandwidth to select only available rates or calculate
the bitrate correctly.
There are some rates in reduced bandwidth modes which can't be
represented as multiples of 500kbps, like 2.25 MBit/s in 5 MHz mode. The
standard suggests to round up to the next multiple of 500kbps, just do
that in mac80211 as well.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[make rate unsigned in ieee80211_add_tx_radiotap_header(), squash fix]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
according to IEEE 802.11-2012 section 18, various timings change
when using 5 MHz and 10 MHz. Reflect this by using a "shift" when
calculating durations.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
There are some APs, notably 2G/3G/4G Wifi routers, specifically the
"Onda PN51T", "Vodafone PocketWiFi 2", "ZTE MF60" and a similar
T-Mobile branded device [1] that erroneously don't include all the
needed information in (re)association response frames. Work around
this by assuming the information is the same as it was in the
beacon or probe response and using the data from there instead.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58881.
[1] https://bbs.archlinux.org/viewtopic.php?pid=1277305
Note that this requires marking the first ieee802_11_parse_elems()
argument const, otherwise we'd get a compiler warning.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Michal Zajac <manwe@manwe.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently beacon availability upon association is marked by have_beacon
flag of assoc_data structure that becomes unavailable when association
completes. However beacon availability indication is required also after
association to inform a driver. Currently dtim_period parameter is used
for this purpose. Move have_beacon flag to another structure, persistant
throughout a interface's life cycle. Use suitable sematics for beacon
availability indication.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
[fix another instance of BSS_CHANGED_DTIM_PERIOD in docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support them only if the driver advertises support for them via
IEEE80211_HW_SUPPORTS_ACTIVE_MONITOR. Unlike normal monitor interfaces,
they are added to the driver, along with their MAC address.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using separate locks in cfg80211 and mac80211 has always
caused issues, for example having to unlock in places in
mac80211 to call cfg80211, which even needed a framework
to make cfg80211 calls after some functions returned etc.
Additionally, I suspect some issues people have reported
with the cfg80211 state getting confused could be due to
such issues, when cfg80211 is asking mac80211 to change
state but mac80211 is in the process of telling cfg80211
that the state changed (in another way.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit 12e7f51702,
IEEE80211_SDATA_DISCONNECT_RESUME no longer worked as
it would simply never be tested. Restore a bit of the
code removed there and in 9b7d72c104
to make it work again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
VHT introduces multiple IEs that need to be parsed for a
wide bandwidth channel switch. Two are (currently) needed
in mac80211:
* wide bandwidth channel switch element
* channel switch wrapper element
The former is contained in the latter for beacons and probe
responses, but not for the spectrum management action frames
so the IE parser needs a new argument to differentiate them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for the secondary channel offset IE in channel
switch announcements. This is necessary for proper handling
of CSA on HT access points.
For this to work it is also necessary to convert everything
here to use chandef structs instead of just channels. The
driver updates aren't really correct though. In particular,
the TI wl18xx driver update can't possibly be right since
it just ignores the new channel width for lack of firmware
API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support extended channel switch when the operating
class is one of the global operating classes as
defined in Annex E of 802.11-2012. If it isn't,
disconnect from the AP instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg notes mac80211 drivers which use
ieee80211_queue_stopped() really only want to know if they
previously requested a queue stop.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It has to be removed from the driver, but completely
destroying it helps handle unplug of a device during
suspend since then the channel context handling etc.
doesn't have to happen later when it's removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of open-coding the accesses and length check do
the length check in the IE parser and assign a struct
pointer for use in the remaining code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's always just one byte, so check for that and
remove the length field from the parser struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's always just one byte, so check for that and
remove the length field from the parser struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the sake of speed of calculation and number accuracy,
mac80211 tracks the RSSI in dBm * 16. But it forgot to
divide back by 16 when the RSSI is asked by the driver.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes queues are flushed in the middle of
operation, which can lead to driver issues.
Stop queues temporarily, while flushing, to
avoid transmitting new packets while they are
being flushed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since now we disconnect before suspend, various code which save
connection state can now be removed from suspend and resume
procedure. Cleanup on resume side is smaller as ieee80211_reconfig()
is also used for H/W restart.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In beacons and association response frames an AP may include an
operating mode notification element to advertise changes in the
number of spatial streams it can receive. Handle this using the
existing function that handles the action frame, but only handle
NSS changes, not bandwidth changes which aren't allowed here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no use for it, WPA is entirely handled in
wpa_supplicant in userspace, so don't pick the IE.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add command to trigger radar detection in the driver/FW.
Once radar detection is started it should continuously
monitor for radars as long as the channel active.
If radar is detected usermode notified with 'radar
detected' event.
Scanning and remain on channel functionality must be disabled
while doing radar detection/scanning, and vice versa.
Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add routines to
- maintain a PS mode for each peer and a non-peer PS mode
- indicate own PS mode in transmitted frames
- track neighbor STAs power modes
- buffer frames when neighbors are in PS mode
- add TIM and Awake Window IE to beacons
- release frames in Mesh Peer Service Periods
Add local_pm to sta_info to represent the link-specific power
mode at this station towards the remote station. When a peer
link is established, use the default power mode stored in mesh
config. Update the PS status if the peering status of a neighbor
changes.
Maintain a mesh power mode for non-peer mesh STAs. Set the
non-peer power mode to active mode during peering. Authenticated
mesh peering is currently not working when either node is
configured to be in power save mode.
Indicate the current power mode in transmitted frames. Use QoS
Nulls to indicate mesh power mode transitions.
For performance reasons, calls to the function setting the frame
flags are placed in HWMP routing routines, as there the STA
pointer is already available.
Add peer_pm to sta_info to represent the peer's link-specific
power mode towards the local station. Add nonpeer_pm to
represent the peer's power mode towards all non-peer stations.
Track power modes based on received frames.
Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS
neighbor counter and group-addressed frame buffer).
Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame
buffering routines in the tx path. Update num_sta_ps to buffer
and release group-addressed frames after DTIM beacons.
Announce the awake window duration in beacons if in light or
deep sleep mode towards any peer or non-peer. Create a TIM IE
similarly to AP mode and add it to mesh beacons. Parse received
Awake Window IEs and check TIM IEs for buffered frames.
Release frames towards peers in mesh Peer Service Periods. Use
the corresponding trigger frames and monitor the MPSP status.
Append a QoS Null as trigger frame if neccessary to properly end
the MPSP. Currently, in HT channels MPSPs behave imperfectly and
show large delay spikes and frame losses.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sending authentication/association frames they
might take a bit of time to go out because we may
have to synchronise with the AP, in particular in
the case where it's really a P2P GO. In this case
the 200ms fixed timeout could potentially be too
short if the beacon interval is relatively large.
For drivers that report TX status we can do better.
Instead of starting the timeout directly, start it
only when the frame status arrives. Since then the
frame was out on the air, we can wait shorter (the
typical response time is supposed to be 30ms, wait
100ms.) Also, if the frame failed to be transmitted
try again right away instead of waiting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, when the driver requires the DTIM period,
mac80211 will wait to hear a beacon before association.
This behavior is suboptimal since some drivers may be
able to deal with knowing the DTIM period after the
association, if they get it at all.
To address this, notify the drivers with bss_info_changed
with the new BSS_CHANGED_DTIM_PERIOD flag when the DTIM
becomes known. This might be when changing to associated,
or later when the entire association was done with only
probe response information.
Rename the hardware flag for the current behaviour to
IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC to more accurately
reflect its behaviour. IEEE80211_HW_NEED_DTIM_PERIOD is
no longer accurate as all drivers get the DTIM period
now, just not before association.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver's resume function can't completely
restore the configuration in the device, it returns
1 from the callback which will be treated like a HW
restart request, but done directly.
In this case, also call the driver's restart_complete()
function so it can finish the reconfiguration there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My commit 529ba6e931
("mac80211: clean up association better in suspend")
introduced a bug when resuming from WoWLAN when a
device reset is desired. This case must not use the
suspend_bss_conf as it hasn't been stored.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The initiator/tx doesn't really identify why an
aggregation session is stopped, give a reason
for stopping that more clearly identifies what's
going on. This will help tell the driver clearly
what is expected of it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For AP/IBSS/mesh interfaces, call the driver to reconfigure
bss_info_changed only if the interface was beaconing before
suspend, otherwise we call the driver and it might interpret
the change as going from enabled to disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When suspending, bss_info_changed() is called to
disable beacons, but managed mode interfaces are
simply removed (bss_info_changed() is called with
"no change" only). This can lead to problems.
To fix this and copy the BSS configuration, clear
it during suspend and restore it on resume.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of assuming 200 bytes are always enough for
all the IEs we add, give the length of the buffer
to the function and warn instead of overrunning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the low-level driver wants to support P2P GO
powersave configuration, it must set the cfg80211
flags and mac80211 will pass the parameters to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sujith reported warnings with suspend/resume due to
channel contexts. When I looked into it, I realised
that the code was completely broken as it unassigned
the channel contexts when suspending, which actually
means they are destroyed.
Eliad Peller then pointed out that we also need to
remove the channel contexts from the driver. When I
looked into this, I also noticed that the code isn't
handling the virtual monitor interface correctly (if
it exists.)
Fix this by calling just the driver methods (if they
are implemented) instead of using the channel context
management code. Also add reconfiguration for the
virtual monitor interface.
Reported-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During testing our mac80211 driver a fatal error occurred which was
signalled to mac80211. Upon performing the reconfiguration of the
device a WARN_ON was triggered. This warning checked the return value
of drv_add_chanctx(). However, this returns -EOPNOTSUPP when the
driver does not provide the callback. As the callback is optional
better check it is defined before calling drv_add_chanctx().
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow drivers to indicate their mactime is at RX completion and adjust
for this in mac80211. Also rename the existing RX_FLAG_MACTIME_MPDU to
RX_FLAG_MACTIME_START to clarify its intent. Based on similar code by
Johannes Berg.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix docs, atheros drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since channel contexts are usually present before
stations can be added to an interface, reassign
before stations them in reconfiguration as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During hardware restart, all interfaces are iterated even
though they haven't been re-added to the driver, document
this behaviour. The same also happens during resume, which
is even more confusing since all of the interfaces were
previously removed from the driver. Make this optional so
drivers relying on the current behaviour can still use it,
but to let drivers that don't want this behaviour disable
it.
Also convert all API users, keeping the old semantics
except in hwsim, where the new normal ones are desired.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver requests a restart (reconfiguration) it
gets all the normal method calls, but can't really tell
why they're happening. Call a new restart_complete op
in the driver when the restart completes, so it could
keep its own state about the restart and clear it there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On resume or firmware recovery, mac80211 sends a null
data packet to see if the AP is still around and hasn't
disconnected us. However, it always does this even if
it wasn't even connected before, leading to a warning
in the new channel context code. Fix this by checking
that it's associated.
Cc: stable@vger.kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.
Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, a lot of setup may be
necessary to start operating as an AP, some of
which may fail. Add an explicit AP start driver
method to make such failures easier to handle,
and add an AP stop driver method for symmetry.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For a local variable there's no need to use the atomic
set_bit() operation, use __set_bit() instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of the current whitelist which accepts duplicates
only for the quiet and vendor IEs, use a blacklist of all
IEs (that we currently parse) that can't be duplicated.
This avoids detecting a beacon as corrupt in the future
when new IEs are added that can be duplicated.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Save the AP's VHT capabilities (in managed
mode) and make them available to the driver
in the station information.
Unlike HT capabilities, they aren't restricted
to the common capabilities, so drivers must be
aware of their own capabilities.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
[fix endian conversion bug ...]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rename struct ieee80211_vht_capabilities to ieee80211_vht_cap
and renamed its member vht_capabilities_info to vht_cap_info.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Non-zero status code may be needed for Authentication frames, e.g.,
when using SAE.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).
Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.
This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.
Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.
Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.
[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Free tx status skbs when draining power save buffers, pending frames, or
when tearing down a vif.
Fixes remaining conditions that can lead to hostapd/wpa_supplicant hangs when
running out of socket write memory.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move ieee80211_send_deauth_disassoc() to util.c to make it
available for the rest of the mac80211 code.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The power constraint IE is always a single byte
so check the size when parsing instead of later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In multi-channel scenarios, the channel that we will
transmit a probe request on isn't always the current
channel (which will be NULL anyway) but will instead
be the channel that the AP is on. Pass the channel
to the ieee80211_send_probe_req() function so it can
be used in the different scenarios. The scan code
continues to pass the current channel, of course.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After cfg80211 got a P2P Device abstraction, add
support to mac80211. Whether it really is supported
or not will depend on whether or not the driver has
support for it, but mac80211 needs to change to be
able to support drivers that need a P2P Device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support using a different MAC address
for the P2P Device address we must first have a
P2P Device abstraction that can be assigned a MAC
address.
This abstraction will also be useful to support
offloading P2P operations to the device, e.g.
periodic listen for discoverability.
Currently, the driver is responsible for assigning
a MAC address to the P2P Device, but this could be
changed by allowing a MAC address to be given to
the NEW_INTERFACE command.
As it has no associated netdev, a P2P Device can
only be identified by its wdev identifier but the
previous patches allowed using the wdev identifier
in various APIs, e.g. remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel switch IE has a fixed size, so we can
discard it in parsing if it's not the right size
and use the right struct pointer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sending probe requests, e.g. during software scanning,
these will go out on the *current* channel, so their IEs
need to be built from the current channel. At other times,
e.g. for beacons or probe request templates, the IEs will
be used on the *operating* channel and using the current
channel instead might result in errors.
Add the appropriate parameters to respect the difference.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using hw.conf.channel is wrong as it could be the
temporary channel if any function like the beacon
get function is called while scanning or during
other temporary out-of-channel activities.
Use oper_channel instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, ps mode is indicated per device (rather than
per interface), which doesn't make a lot of sense.
Moreover, there are subtle bugs caused by the inability
to indicate ps change along with other changes
(e.g. when the AP deauth us, we'd like to indicate
CHANGED_PS | CHANGED_ASSOC, as changing PS before
notifying about disassociation will result in null-packets
being sent (if IEEE80211_HW_SUPPORTS_DYNAMIC_PS) while
the sta is already disconnected.)
Keep the current per-device notifications, and add
parallel per-vif notifications.
In order to keep it simple, the per-device ps and
the per-vif ps are orthogonal - the per-vif ps
configuration is determined only by the user
configuration (enable/disable) and the connection
state, and is not affected by other vifs state and
(temporary) dynamic_ps/offchannel operations
(unlike per-device ps).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the virtual monitor interface is requested
by the driver, it should also be iterated over
when the driver wants to iterate all active
interfaces.
To allow that protect it with the iflist_mtx.
Change-Id: I58ac5de2f4ce93d12c5a98ecd2859f60158d5d69
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function building probe-request IEs does not validate the band is
supported before dereferencing it. This can result in a panic when
all bands are traversed, as done during sched-scan start.
Warn when this happens and return an empty probe request. Also fix
sched-scan to not waste memory on unsupported bands.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Larry (and some others I think) reported that with
single-queue drivers mac80211 crashes when waking
the queues. This happens because we allocate just
a single queue for each virtual interface in case
the driver doesn't have at least 4 queues, but the
code stopping/waking the virtual interface queues
wasn't taking this into account.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the interfaces were removed just before a restart
work was started, open_count will be 0, and most of
the reconfig work will be skipped, including the
resetting of local->in_reconfig to false.
Leaving local->inconfig = true will result in
dropping any incoming packet.
Fix it by always setting local->in_reconfig = false
(even if there are no active interfaces).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This and ieee80211_add_ext_srates_ie() aren't
exported, so can't be used by drivers anyway,
but there's also no reason that they should be
so make them private to mac80211 and use sdata
instead of vif arguments.
Acked-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While HW reconfig is in progress, drop all incoming Rx. This prevents
incoming packets from changing the internal state of the driver or
calling callbacks of the low level driver while it is in inconsistent
state.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When performing a HW restart for an AP mode interface, add stations back
only after the AP is beaconing. This mimics the normal flow of STA
addition on AP.
Some devices (wlcore) do not support adding stations before beaconing,
so this has the added benefit of making recovery work for them.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For each EDCA TX queue change default settings (in STA mode) to conform
old 802.11b/g channel access rules. This is needed for drivers that do
not have QoS enable/disable "switch" (like rt2x00) to make them work
properly with legacy APs.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of hardware reconfig mac80211 tries
to restore the station state to its values
before the hardware reconfig, but it only
goes to the last-state - 1. Fix this
off-by-one error.
Cc: stable@kernel.org [3.4]
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WLAN_STA_BLOCK_BA is set while suspending but doesn't get cleared
when resuming in case of wowlan. This causes further ADDBA requests
received to be rejected. Fix it by clearing it in the wowlan path
as well.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Average beacon signal only keep tracked by managed interface,
give warning and return 0 for the others.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_ave_rssi need to be declare as export for driver to use it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to IEEE 802.11 8.4.2.59, set the "STA channel width" bit to 0
if transmitting STA is using a 20mhz channel.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add utility function to provide the average rssi per vif
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removes hw.conf.channel usage from the following functions:
* ieee80211_mandatory_rates
* ieee80211_sta_get_rates
* ieee80211_frame_duration
* ieee80211_rts_duration
* ieee80211_ctstoself_duration
This is in preparation for multi-channel operation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 currently only supports one hardware queue
per AC. This is already problematic for off-channel
uses since if we go off channel while the BE queue
is full and then try to send an off-channel frame
the frame will never go out. This will become worse
when we support multi-channel since then a queue on
one channel might be full, but we have to stop the
software queue for all channels. That is obviously
not desirable.
To address this problem allow drivers to register
more hardware queues, and allow them to map them to
virtual interfaces. When they stop a hardware queue
the corresponding AC software queues on the correct
interfaces will be stopped as well. Additionally,
there's an off-channel queue to solve that problem
and a per-interface after-DTIM beacon queue. This
allows drivers to manage software queues closer to
how the hardware works.
Currently, there's a limit of 16 hardware queues.
This may or may not be sufficient, we can adjust it
as needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue mapping redesign that I'm planning to do
will break pure injection unless we handle monitor
interfaces explicitly. One possible option would
be to have the driver tell mac80211 about monitor
mode queues etc., but that would duplicate the API
since we already need to have queue assignments
handled per virtual interface.
So in order to solve this, have a virtual monitor
interface that is added whenever all active vifs
are monitors. We could also use the state of one
of the monitor interfaces, but managing that would
be complicated, so allocate separate state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Basic rates are added with supported rates IE and extended supported
rates IE.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When adding pending SKBs there's no need to
stop all queues, we only need to stop those
that we're adding frames to. Implement that
by lazily stopping a queue as we add an SKB.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the queue status changes we need to do a fair
bit of work, so ignore no-op changes early.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that don't support QoS also don't support
setting up their ACs, catch that early. While at
it, remove the input check since cfg80211 does it
now.
Also fix up the restart code to not try to set up
the queues in this case.
Finally also change the tx_conf array to have
IEEE80211_NUM_ACS entries instead of # of queues
since that's what it really needs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the AC constants instead of hard-coding
the numbers with comments.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a trivial wrapper function, inline it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since some of the HT code pre-dates 802.11n-2009
some names are wrong. The one that bothers me most
is that "HT operation" is called "HT information"
in our code and that causes confusion.
Rename "HT information" to "HT operation" and also
the control_chan field to primary_chan to match
the name used in the spec.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 is lenient with respect to reception of corrupted beacons.
Even if the frame is corrupted as a whole, the available IE elements
are still passed back and accepted, sometimes replacing legitimate
data. It is unknown to what extent this "feature" is made use of,
but it is clear that in some cases, this is detrimental. One such
case is reported in http://crosbug.com/26832 where an AP corrupts
its beacons but not its probe responses.
One approach would be to completely reject frames with invaid data
(for example, if the last tag extends beyond the end of the enclosing
PDU). The enclosed approach is much more conservative: we simply
prevent later IEs from overwriting the state from previous ones.
This approach hopes that there might be some salient data in the
IE stream before the corruption, and seeks to at least prevent that
data from being overwritten. This approach will fix the case above.
Further, we flag element structures that contain data we think might
be corrupted, so that as we fill the mac80211 BSS structure, we try
not to replace data from an un-corrupted probe response with that
of a corrupted beacon, for example.
Short of any statistics gathering in the various forms of AP breakage,
it's not possible to ascertain the side effects of more stringent
discarding of data.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Cc: Sam Leffler <sleffler@chromium.org>
Cc: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When associating and particularly when disassociating
there's no need to notify the driver about changes
with multiple calls to bss_info_changed, we should
combine the QoS enabling/disabling into the same call
as otherwise the driver could get confused about QoS
suddenly getting disabled while connected.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
That's a lot longer than open-coding it and
doesn't really add value, so just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of maintaining separate sta_add/sta_remove
callsites, implement it in sta_state when the driver
has no sta_state implementation.
The only behavioural change this should cause is in
secure mesh mode: with this the station entries will
only be created after the stations are set to AUTH.
Given which drivers support mesh, this seems to not
be a problem.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(based on Eliad's patch)
Add a callback to notify the low-level driver whenever
the state of a station changes. The driver is only
notified when the station is actually in the mac80211
hash table, not for pre-insert state transitions.
To allow the driver to replace sta_add/remove calls
with this, call extra transitions with the NOTEXIST
state.
This callback can fail, so we need to be careful in
handling it when a station is inserted, particularly
in the IBSS case where we still keep the station entry
around for mac80211 purposes.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting keys and updating TKIP keys must use the
BSS sdata (not AP_VLAN), so we translate. Move
the translation into driver-ops wrappers instead
of having it inline in the code to simplify the
normal code flow.
The same can be done for sta_add/remove which
already does the translation in the wrapper.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sta might be in psm against the ap (e.g. because
this was the before a hw restart), so we explicitly
send a null packet in order to make sure it'll
sync against the ap (and get out of psm).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of authentication frame exchange between two IBSS STAs, the
DA field must contain the destinatioin address (instead of the BSSID).
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ideally, hardware/firmware initialization is complete after the
drv_start routine. In mac80211 restart code (ieee80211_reconfig),
defer calling the driver commands i.e. setup fragmentation
threshold, rts threshold and coverage class till drv_start
routine is called.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
v2: Removed extra blank line added.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure arp filtering on sta reconfiguration.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Follow 802.11n-2009 9.13.3.1 for protection mode and ADDBA
* Send ADDBA only to HT STAs - implement 11.5.1.1 partially
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due the a fall-through in the switch statement, the IBSS mode got a
report for AP_RPOBE_RESPONSE change on reconfig. Change this to an AP
only notification.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements ht-cap over-rides for mac80211 drivers.
HT may be disabled, making an /a/b/g/n station act like an
a/b/g station. HT40 may be disabled forcing the station to
be HT20 even if the AP and local hardware support HT40.
MAX-AMSDU may be disabled.
AMPDU-Density may be increased.
AMPDU-Factor may be decreased.
This has been successfully tested with ath9k using patched
wpa_supplicant and iw.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No other driver ever ended up using this, and
the commit forgot to move the prototype so no
driver could have used it. Revert it, if any
driver shows up and needs it it can be moved
again, but until then it's more efficient to
have it in mac80211 where the only user is.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are currently linking the skbs by using skb->next
directly. This works, but the preferred way is to use
a struct sk_buff_head instead. That also prepares for
passing that to drivers directly.
While at it I noticed we calculate the duration for
fragments twice -- remove one of them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow setting a probe response template for an interface operating in
AP mode. Low level drivers are notified about changes in the probe
response template and are able to retrieve a copy of the current probe
response. This data can, for example, be uploaded to hardware as a
template.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver should be instructed to enter PS AFTER
reconfiguring ASSOCIATED (in STA case) using ieee80211_bss_info_change_notify
same as it's being done in ieee80211_set_associated()
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver is never informed about monitor or
AP_VLAN interfaces, so whenever we pass those
to it later this is a bug. Verify we don't as
there are some cases where this could happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vif might be busy while reconfiguring
(e.g. associated), so indicate BSS_CHANGED_IDLE as well.
Reported-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_probereq_get() can return NULL in
which case we should clean up & return NULL
in ieee80211_build_probe_req() as well.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some refactoring for IBSS HT.
Move HT info and capability IEs building code into separate functions.
Add function to get the channel type from an HT info IE.
Signed-off-by: Alexander Simon <an.alexsimon@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These files are non modular, but need to export symbols using
the macros now living in export.h -- call out the include so
that things won't break when we remove the implicit presence
of module.h from everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The flaglock in struct sta_info has long been
something that I wanted to get rid of, this
finally does the conversion to atomic bitops.
The conversion itself is straight-forward in
most places, a few things needed to change a
bit since we can no longer use multiple bits
at the same time.
On x86-64, this is a fairly significant code
size reduction:
text data bss dec hex
427861 23648 1008 452517 6e7a5 before
425383 23648 976 450007 6ddd7 after
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we no longer use the return value, we no
longer need to maintain it either, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Relocate the mesh implementation of adding the (extended) supported
rates IE to util.c, anticipating its use by other parts of mac80211.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
save and configure tx param per sdata, rather than
per hardware.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the scan request or tx_mgmt is requesting not to
use CCK rate for managemet frames through
NL80211_ATTR_TX_NO_CCK_RATE attribute, then mac80211 should
select appropriate least non-CCK rate. This could help to
send P2P probes and P2P action frames at non 11b rates
without diabling 11b rates globally.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set SSID information from nl80211 beacon parameters. Advertise changes
in SSID to low level drivers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removing unnecessary messages saves code and text.
Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moving the parsing logic for retrieving the information elements
stored in management frames, e.g. beacons or probe responses,
and making it available to other cfg80211 drivers.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers might assume sta.drv_priv is clear while
the sta is added, so clear it on reconfinguration.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scanning currently uses the TX rate mask to
restrict the rate set, which is bogus. Make
it use the new set of rates from userspace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add tx_conf array to save the current tx queues
configuration, and reconfig it on resume (ieee80211_reconfig).
On resume, the driver is being reconfigured. Without
reconfiguring the tx queues as well, the driver might
configure the device to use wrong ac params (e.g. ps-poll
instead of uapsd).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When suspending with all netdevs down, the device
is stopped but we still call a number of driver
callbacks that the driver might not expect. The
same happens during resume, we might call a few
callbacks without starting the driver. Fix this
by checking open_count around more things and
exiting quickly if it is 0.
Also, while at this I noticed that the coverage
class isn't reprogrammed after resume, so add
that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In WoWLAN, devices may use crypto keys for TX/RX
and could also implement GTK rekeying. If the
driver isn't able to retrieve replay counters and
similar information from the device upon resume,
or if the device isn't responsive due to platform
issues, it isn't safe to keep the connection up
as GTK rekey messages from during the sleep time
could be replayed against it.
The only protection against that is disconnecting
from the AP. Modifying mac80211 to do that while
it is resuming would be very complex and invasive
in the case that the driver requires a reconfig,
so do it after it has resumed completely. In that
case, however, packets might be replayed since it
can then only happen after TX/RX are up again, so
mark keys for interfaces that need to disconnect
as "tainted" and drop all packets that are sent
or received with those keys.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 maintains a running average of the RSSI when a STA
is associated to an AP. Report threshold events to any driver
that has registered callbacks for getting RSSI measurements.
Implement callbacks in mac80211 so that driver can set thresholds.
Add callbacks in mac80211 which is invoked when an RSSI threshold
event occurs.
mac80211: add tracing to rssi_reports api and remove extraneous fn argument
mac80211: scale up rssi thresholds from driver by 16 before storing
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not send DS Channel parameter for directed probe requests
in order to maximize the chance that we get a response. Some
badly-behaved APs don't respond when this parameter is included.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Function ieee80211_reconfig in net/mac80211/util.c contains label wake_up
which is defined unconditionally, but only used with CONFIG_PM. Gcc
warns about this when CONFIG_PM is not defined.
This patch makes the label's definition dependent on CONFIG_PM too,
eliminating the warning.
The issue was apparently introduced in git commit
eecc48000a.
Signed-off-by: Vincent Zweije <vincent@zweije.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds basic support for the new WoWLAN
configuration in mac80211. The behaviour is
completely offloaded to the driver though,
with two new callbacks (suspend/resume).
Options for the driver include a complete
reconfiguration after wakeup, and exposing
all the triggers it wants to support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently run this timer exactly once when
a new mac80211 device is registered, but that
is completely pointless since it will have no
work to do at all. Therefore, remove that and
also simplify some code using the timer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The module parameter ieee80211_disable_40mhz_24ghz
was meant to allow disabling 40 MHz operation in
the 2.4 GHz band by default. However, it is buggy
as implemented because while it advertises to the
AP that the device doesn't support 40 MHz, it will
itself still use 40 MHz configurations.
To fix this, clear the 40 MHz bits from the sband
completely instead of overriding where used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The throughput LED trigger was always active when
the radio was enabled. In most cases that's likely
the desired behaviour, but iwlwifi requires it to
be only active when one of the virtual interfaces
is actually "connected" in some way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi and other drivers like to blink their LED
based on throughput. Implement this generically in
mac80211, based on a throughput table the driver
specifies. That way, drivers can set the blink
frequencies depending on their desired behaviour
and max throughput.
All the drivers need to do is provide an LED class
device, best with blink hardware offload.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code to handle powersaving stations has a race:
when the powersave flag is lifted from a station,
we could transmit a packet that is being processed
for TX at the same time right away, even if there
are other frames queued for it. This would cause
frame reordering. To fix this, lift the flag only
under the appropriate lock that blocks TX.
Additionally, the code to allow drivers to block a
station while frames for it are on the HW queue is
never re-enabled the station, so traffic would get
stuck indefinitely. Fix this by clearing the flag
for this appropriately.
Finally, as an optimisation, don't do anything if
the driver unblocks an already unblocked station.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chipsets with hardware based connection monitoring need to autonomically
send directed probe-request frames to the AP (in the event of beacon loss,
for example.)
For the hardware to be able to do this, it requires a template for the frame
to transmit to the AP, filled in with the BSSID and SSID of the AP, but also
the supported rate IE's.
This patch adds a function to mac80211, which allows the hardware driver to
fetch this template after association, so it can be configured to the hardware.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The lower driver is notified when the fragmentation threshold changes
and upon a reconfig of the interface.
If the driver supports hardware TX fragmentation, don't fragment
packets in the stack.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When roaming while we have active BA session,
we can end up transmitting delBA frames to
the old AP while we're already on the new AP's
channel, which can cause warnings.
Simply avoid sending those frames, but still
tear down the internal session state, since
they are not really necessary anyway as we
will implicitly disassociate when sending the
association to the new AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The locking around ieee80211_recalc_smps is
buggy -- it cannot acquire another interface's
mutex while the iflist mutex is held because
another code path could be holding the iface
mutex and trying to acquire the iflist mutex.
But the locking is also unnecessary, we only
check "ifmgd->associated" as a bool, and don't
use the pointer (in check_mgd_smps).
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE Std 802.11k-2008 added DS Parameter Set information element into
Probe Request frames as an optional information on 2.4 GHz band (and
mandatory, if radio measurements are enabled). This allows APs to
filter out Probe Request frames that may be received from neighboring
overlapping channels and by doing so, reduce the number of unnecessary
frames in the air. Make mac80211 add this IE into Probe Request frames
whenever the channel is known (i.e., whenever hwscan is not used).
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the TX rate set has been masked, the removed rates can also be
removed from the Supported Rates and Extended Supported Rates IEs in
Probe Request frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a driver advertises p2p device support,
mac80211 will handle it, but internally it will
rewrite the interface type to STA/AP rather than
P2P-STA/GO since otherwise a lot of paths need
to be touched that are otherwise identical. A
p2p boolean tells drivers whether or not a given
interface will be used for p2p or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using a WARN_ON(!mutex_is_locked())
use lockdep_assert_held() which compiles away
completely when lockdep isn't enabled, and
also is a more accurate assertion since it
checks that the current thread is holding the
mutex.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Somebody noticed this problem, and I outlined
to them how to fix it, but haven't heard back
from them. So while I was adding the state
field I figured I could use it to fix it.
The problem, as I understand it, is that when
we go offchannel while the driver has a queue
stopped, the driver will likely start draining
the queue and then enable it while offchannel.
This in turn will enable the interface queue,
and that leads to transmitting data frames on
the wrong channel.
Fix this by keeping track of offchannel status
per interface, and not enabling the interface
queues on interfaces that are offchannel when
the driver enables a queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the introduction of ieee80211_sdata_running(),
some new code was introduced that uses netif_running()
instead. Switch all these instances over.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are subqueue helpers so that we don't
need to get the TX queue and then wake/stop
it, use those helpers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to register for more than just
action frames by giving the frame subtype, and
make it possible to use this in various modes
as well.
With some tweaks and some added functionality
this will, in the future, also be usable in AP
mode and be able to replace the cooked monitor
interface currently used in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In AP mode, there is no need to notify the driver about QoS
changes for the monitor interface that is created. The warning
in ieee80211_bss_info_change_notify() would be hit otherwise.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since
commit e1b3ec1a2a
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Mon Mar 29 12:18:34 2010 +0200
mac80211: explicitly disable/enable QoS
mac80211 is telling drivers, in particular
iwlwifi, whether QoS is enabled or not.
However, this is only relevant for station mode,
since only then will any device send nullfunc
frames and need to know whether they should be
QoS frames or not. In other modes, there are
(currently) no frames the device is supposed to
send.
When you now consider virtual interfaces, it
becomes apparent that the current mechanism is
inadequate since it enables/disables QoS on a
global scale, where for nullfunc frames it has
to be on a per-interface scale.
Due to the above considerations, we can change
the way mac80211 advertises the QoS state to
drivers to only ever advertise it as "off" in
station mode, and make it a per-BSS setting.
Tested-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A number of places use RCU locking for accessing
the station list, even though they do not need
to. Use mutex locking instead to prepare for the
locking changes I want to make. The mlme code is
also using a WLAN_STA_DISASSOC flag that has the
same meaning as WLAN_STA_BLOCK_BA, so use that.
While doing so, combine places where we loop
over stations twice, and optimise away some of
the loops by checking if the hardware supports
aggregation at all first.
Also fix a more theoretical race condition: right
now we could resume, set up an aggregation session,
and right after tear it down again due to the code
that is needed for hardware reconfiguration here.
Also mark add a comment to that code marking it as
a workaround.
Finally, remove a pointless aggregation disabling
loop when an interface is stopped, directly after
that we remove all stations from it which will also
disable all aggregation sessions that may still be
active, and does so in a race-free way unlike the
current loop that doesn't block new sessions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When reconfiguring an interface due to a previous
hardware restart, mac80211 will currently include
the new IBSS flag on non-IBSS interfaces which may
confuse drivers.
Instead of doing the ~0 trick, simply spell out
which things are going to be reconfigured.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enhance tracing by adding tracing for a variety of
callbacks that the drivers call, and also for
internal calls (currently limited to queue status).
This can aid debugging what is going on in mac80211
in interaction with drivers, since we can now see
what drivers call and not just what mac80211 calls
in the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I want to use it during station destruction as well
so rename it to WLAN_STA_BLOCK_BA which is also the
only use of it now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add interface to disable/enable QoS (aka WMM or WME). Currently drivers
enable it explicitly when ->conf_tx method is called, and newer disable.
Disabling is needed for some APs, which do not support QoS, such
we should send QoS frames to them.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: fix skb buffering issue" still left a race
between enabling the hardware queues and the virtual
interface queues. In hindsight it's totally obvious
that enabling the netdev queues for a hardware queue
when the hardware queue is enabled is wrong, because
it could well possible that we can fill the hw queue
with packets we already have pending. Thus, we must
only enable the netdev queues once all the pending
packets have been processed and sent off to the device.
In testing, I haven't been able to trigger this race
condition, but it's clearly there, possibly only when
aggregation is being enabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When there is a need to restart/reconfig hw, tear down all the
aggregation queues and let the mac80211 and driver get in-sync to have
the opportunity to re-establish the aggregation queues again.
Need to wait until driver re-establish all the station information before tear
down the aggregation queues, driver(at least iwlwifi driver) will reject the
stop aggregation queue request if station is not ready. But also need to make
sure the aggregation queues are tear down before waking up the queues, so
mac80211 will not sending frames with aggregation bit set.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many drivers would like to sleep during station
addition and removal, and currently have a high
complexity there from not being able to.
This introduces two new callbacks sta_add() and
sta_remove() that drivers can implement instead
of using sta_notify() and that can sleep, and
the new sta_add() callback is also allowed to
fail.
The reason we didn't do this previously is that
the IBSS code wants to insert stations from the
RX path, which is a tasklet, so cannot sleep.
This patch will keep the station allocation in
that path, but moves adding the station to the
driver out of line. Since the addition can now
fail, we can have IBSS peer structs the driver
rejected -- in that case we still talk to the
station but never tell the driver about it in
the control.sta pointer. If there will ever be
a driver that has a low limit on the number of
stations and that cannot talk to any stations
that are not known to it, we need to do come up
with a new strategy of handling larger IBSSs,
maybe quicker expiry or rejecting peers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chun-Yeow Yeoh