We had set the platform drvdata in rspi_probe() as a type of
struct rspi_data, but use it as struct spi_master in rspi_remove()
Fix by remove the unnecessary spi_master_[get|put]() since rspi->master
is no longer used after spi_unregister_master().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
The R8A7790 has QSPI module which added into RSPI together.
The transmit or receive data should be read from or written to
with the longword-, word-, or byte-access width. Modify word-
access to byte-access. In 16-bit data register, QSPI send or
receive datas access from high 8-bit while RSPI send or receive
datas access from low 8-bit on single mode.
Modify to reset transmit-receive buffer data and reading dummy
after data are transmited. RSPI has a TXMD bit on control
register(SPCR) to set transmit-only mode when transmit data or
Full-duplex synchronous mode when receive data. In QSPI the TXMD
bit is not supported, so after transmit data, dummy should be
read and before transmit or receive data the bufer register
should be reset.
This driver is the implementation of send and receive pio only,
DMA is not supported at this time.
Without this patch, it will occur error when transmit and receive
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
The R8A7790 has QSPI module which is very similar to RSPI.
This patch adds into RSPI module together to supports QSPI module.
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
In rspi_remove(), current code dereferences rspi after spi_unregister_master(),
thus add an extra spi_master_get() call is necessary to prevent use after free.
Current code already has an extra spi_master_put() call in rspi_remove(), so
this patch just adds a spi_master_get() call rather than a spi_master_get() with
spi_master_put() calls.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Don't rely on shdma dhaengine driver getting DMA slave addresses from its
slave configuration. Instead provide those addresses, using a
dmaengine_slave_config() call.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Bill Pemberton has done most of the legwork on this series. I've used
his script to purge the attributes from the drivers/gpio tree.
Reported-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Because the latest shdma driver changed, it caused build error in
the spi-rspi driver. This patch fixed the build error.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds dmaengine supporting using sh_dma driver. The module
receives data by DMAC, it also needs TX DMAC to generate SPI's clocks.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The SH7757 has RSPI module. This patch supports it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Wei Yongjun