On MPC8572 and MPC8536 the status of GPIO pins configured
as output cannot be determined by reading GPDAT register.
Workaround by reading the status of input pins from GPDAT
and the status of output pins from a shadow register.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Port C interrupts can be either falling edge, or either edge.
Other external interrupts are either falling edge or active low.
Tested on a custom 8280 based board.
Signed-off-by: Mark Ware <mware@elphinstone.net>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It appears that we wrongly calculate dev_base for type1 config cycles.
The thing is: we shouldn't subtract hose->first_busno because PCI core
sets PCI primary, secondary and subordinate bus numbers, and PCIe
controller actually takes the registers into account. So we should use
just bus->number.
Also, according to MPC8315 reference manual, primary bus number should
always remain 0. We have PPC_INDIRECT_TYPE_SURPRESS_PRIMARY_BUS quirk
in indirect_pci.c, but since 83xx is somewhat special, it doesn't use
indirect_pci.c routines, so we have to implement the quirk specifically
for 83xx PCIe controllers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Writing a driver using SCLPC on the MPC5200B I detected, that the
intspec arrays to map irqs to Linux virq cannot be const, because the
mapping and xlate functions only take non const pointers. All those
functions do not modify the intspec, so a const pointer could be used.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The typename member of struct irq_chip was kept for migration purposes
and is obsolete since more than 2 years. Fix up the leftovers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@ozlabs.org
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds suspend/resume support for MPC8540 and MPC8641D-
compatible CPUs. To reach sleep state, we just write the SLP bit
into the PM control and status register.
So far we don't support Deep Sleep mode as found in newer MPC85xx
CPUs (i.e. MPC8536). It can be relatively easy implemented though,
and for it we reserve 'mem' suspend type.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
So far the driver is used to reset QE upon resume, which is needed on
85xx. Later we can move some QE initialization steps into probe().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It appears that QE shuts down on all MPC85xx CPUs (i.e. MPC8568 and
MPC8569) and thus needs reset upon resume.
So modify qe_alive_during_sleep() to account that.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For MPC8569 CPUs we'll need to reset QE after each suspend, so make
qe_reset() code path suitable for repeated invocation, that is:
- Don't initialize rheap structures if already initialized;
- Don't allocate muram for SDMA if already allocated, just reinitialize
registers with previously allocated muram offset;
- Remove __init attributes from qe_reset() and cpm_muram_init();
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8569 CPUs have four QE RISCs, so we need to increase MAX_QE_RISC
constant, otherwise qe_upload_firmware() fails at sanity checking.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
get_irq_desc() is a powerpc-specific version of irq_to_desc(). That
is reason enough to remove it, but it also doesn't know about sparse
irq_desc support which irq_to_desc() does (when we enable it).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Sometimes this is used to hold a simple offset, and sometimes
it is used to hold a pointer. This patch changes it to a union containing
void * and dma_addr_t. get/set accessors are also provided, because it was
getting a bit ugly to get to the actual data.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (134 commits)
powerpc/nvram: Enable use Generic NVRAM driver for different size chips
powerpc/iseries: Fix oops reading from /proc/iSeries/mf/*/cmdline
powerpc/ps3: Workaround for flash memory I/O error
powerpc/booke: Don't set DABR on 64-bit BookE, use DAC1 instead
powerpc/perf_counters: Reduce stack usage of power_check_constraints
powerpc: Fix bug where perf_counters breaks oprofile
powerpc/85xx: Fix SMP compile error and allow NULL for smp_ops
powerpc/irq: Improve nanodoc
powerpc: Fix some late PowerMac G5 with PCIe ATI graphics
powerpc/fsl-booke: Use HW PTE format if CONFIG_PTE_64BIT
powerpc/book3e: Add missing page sizes
powerpc/pseries: Fix to handle slb resize across migration
powerpc/powermac: Thermal control turns system off too eagerly
powerpc/pci: Merge ppc32 and ppc64 versions of phb_scan()
powerpc/405ex: support cuImage via included dtb
powerpc/405ex: provide necessary fixup function to support cuImage
powerpc/40x: Add support for the ESTeem 195E (PPC405EP) SBC
powerpc/44x: Add Eiger AMCC (AppliedMicro) PPC460SX evaluation board support.
powerpc/44x: Update Arches defconfig
powerpc/44x: Update Arches dts
...
Fix up conflicts in drivers/char/agp/uninorth-agp.c
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
This patch fixes a null pointer exception caused by removal of
'ack()' for level interrupts in the Xilinx interrupt driver. A recent
change to the xilinx interrupt controller removed the ack hook for
level irqs.
Signed-off-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some CPUs (i.e. MPC8569) QE shuts down completely during sleep,
drivers may want to know that to reinitialize registers and buffer
descriptors.
This patch implements qe_alive_during_sleep() helper function, so far
it just checks if MPC8569-compatible power management controller is
present, which is a sign that QE turns off during sleep.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids having a short glitch if the desired initial value is not
the same as what was previously in the data register.
Signed-off-by: Michael Barkowski <michaelbarkowski@ruggedcom.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some CPU, like the MPC8560 don't have a RSTCR in the Global
Utilities Block. These boards will implement their own reboot
call, and not use this code, so we should only warn about the
absence of the GUTS RSTCR when the default reboot code is used.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a byte length read and write interface compatible with the
nvram_generic driver interface to the mmio driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Error handling code following a kzalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Error handling code following a kzalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
in case the interrupt controller was used in an earlier life then it is
possible it is that some of its sources were used and are still unmask.
If the (unmasked) device is active and is creating interrupts (or one
interrupts was pending since the interrupts were disabled) then the boot
process "ends" very soon. Once external interrupts are enabled, we land in
-> do_IRQ
-> call ppc_md.get_irq()
-> ipic_read() gets the source number
-> irq_linear_revmap(source)
-> revmap[source] == NO_IRQ
-> irq_find_mapping(source) returns NO_IRQ because no source
is registered
-> source is NO_IRQ, ppc_spurious_interrupts gets incremented, no
further action.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Check that the result of kmalloc/kzalloc is not NULL before dereferencing it.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
identifier f;
constant char *C;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
... when != x == NULL
when != x != NULL
when != (x || ...)
(
kfree(x)
|
f(...,C,...,x,...)
|
*f(...,x,...)
|
*x->f
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The workaround enabled by CONFIG_MPIC_BROKEN_REGREAD does not work
on non-broken MPICs. The symptom is no interrupts being received.
The fix is twofold. Firstly the code was broken for multiple isus,
we need to index into the shadow array with the src_no, not the idx.
Secondly, we always do the read, but only use the VECPRI_MASK and
VECPRI_ACTIVITY bits from the hardware, the rest of "val" comes
from the shadow.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 31207dab7d
"Fix incorrect allocation of interrupt rev-map"
introduced a regression crashing on boot on machines using
a "DCR" based MPIC, such as the Cell blades.
The reason is that the irq host data structure is initialized
much later as a result of that patch, causing our calls to
mpic_map() do be done before we have a host setup.
Unfortunately, this breaks _mpic_map_dcr() which uses the
mpic->irqhost to get to the device node.
This fixes it by, instead, passing the device node explicitely
to mpic_map().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Akira Tsukamoto <akirat@rd.scei.sony.co.jp>
The qe_issue_cmd() function (Freescale PowerPC QUICC Engine library) polls
on a register until a status bit changes, but does not include a timeout
to handle the situation if the bit never changes. Change the code to use
the new spin_event_timeout() macro, which simplifies polling on a register
without a timeout.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
So far, MPC512x used mpc512x_find_ips_freq() to get the bus frequency,
while MPC52xx used mpc52xx_find_ipb_freq(). Despite the different
clock names (IPS vs. IPB) the code was identical.
Use common code for both processor families.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add the option to build the code under arch/powerpc with -Werror.
The intention is to make it harder for people to inadvertantly introduce
warnings in the arch/powerpc code. It needs to be configurable so that
if a warning is introduced, people can easily work around it while it's
being fixed.
The option is a negative, ie. don't enable -Werror, so that it will be
turned on for allyes and allmodconfig builds.
The default is n, in the hope that developers will build with -Werror,
that will probably lead to some build breaks, I am prepared to be flamed.
It's not enabled for math-emu, which is a steaming pile of warnings.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits)
block: add request clone interface (v2)
floppy: fix hibernation
ramdisk: remove long-deprecated "ramdisk=" boot-time parameter
fs/bio.c: add missing __user annotation
block: prevent possible io_context->refcount overflow
Add serial number support for virtio_blk, V4a
block: Add missing bounce_pfn stacking and fix comments
Revert "block: Fix bounce limit setting in DM"
cciss: decode unit attention in SCSI error handling code
cciss: Remove no longer needed sendcmd reject processing code
cciss: change SCSI error handling routines to work with interrupts enabled.
cciss: separate error processing and command retrying code in sendcmd_withirq_core()
cciss: factor out fix target status processing code from sendcmd functions
cciss: simplify interface of sendcmd() and sendcmd_withirq()
cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code
cciss: Use schedule_timeout_uninterruptible in SCSI error handling code
block: needs to set the residual length of a bidi request
Revert "block: implement blkdev_readpages"
block: Fix bounce limit setting in DM
Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt
...
Manually fix conflicts with tracing updates in:
block/blk-sysfs.c
drivers/ide/ide-atapi.c
drivers/ide/ide-cd.c
drivers/ide/ide-floppy.c
drivers/ide/ide-tape.c
include/trace/events/block.h
kernel/trace/blktrace.c
This patch refactors some of the xilinx_intc interrupt controller driver
and adds support for cascading an i8259 off one of the irq lines.
This patch was based on the ML510 support work done by Roderick
Colenbrander.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support for the Xilinx plbv46-pci-1.03.a PCI host
bridge IPcore.
Signed-off-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Conflicts:
arch/mips/sibyte/bcm1480/irq.c
arch/mips/sibyte/sb1250/irq.c
Merge reason: we gathered a few conflicts plus update to latest upstream fixes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We shouldn't directly access sysdata to get the pci_controller. Instead
use pci_bus_to_host() for this purpose. In the future we might have
sysdata be a device_node to match ppc64 and unify the code between ppc32
& ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the pci_controller. Instead
use pci_bus_to_host() for this purpose. In the future we might have
sysdata be a device_node to match ppc64 and unify the code between ppc32
& ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the pci_controller. Instead
use pci_bus_to_host() for this purpose. In the future we might have
sysdata be a device_node to match ppc64 and unify the code between ppc32
& ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the pci_controller. Instead
use pci_bus_to_host() for this purpose. In the future we might have
sysdata be a device_node to match ppc64 and unify the code between ppc32
& ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
mpic_find() was overloaded to do two things, finding the mpic instance
for a given interrupt and returning if it's an IPI. Instead we introduce
mpic_is_ipi() and simplify mpic_find() to just return the mpic instance
Also silences the warning:
arch/powerpc/sysdev/mpic.c: In function 'mpic_irq_set_priority':
arch/powerpc/sysdev/mpic.c:1382: warning: 'is_ipi' may be used uninitialized in this function
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Previouslly we just always set the inbound window to 2G. This was
broken for systems with >2G. If a system has >=4G we will need
SWIOTLB support to handle that case.
We now allocate PCICSRBAR/PEXCSRBAR right below the lowest PCI outbound
address for MMIO or the 4G boundary (if the lowest PCI address is above
4G).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P2020 is a dual e500v2 core based SOC with:
* 3 PCIe controllers
* 2 General purpose DMA controllers
* 2 sRIO controllers
* 3 eTSECS
* USB 2.0
* SDHC
* SPI, I2C, DUART
* enhanced localbus
* and optional Security (P2020E) security w/XOR acceleration
The p2020 DS reference board is pretty similar to the existing MPC85xx
DS boards and has a ULI 1575 connected on one of the PCIe controllers.
Signed-off-by: Ted Peters <Ted.Peters@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We we build with resource_size_t as a 64-bit quantity we get:
arch/powerpc/sysdev/fsl_rio.c: In function 'fsl_rio_setup':
arch/powerpc/sysdev/fsl_rio.c:1029: warning: format '%08x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
arch/powerpc/sysdev/fsl_rio.c:1029: warning: format '%08x' expects type 'unsigned int', but argument 5 has type 'resource_size_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Its feasible based on how the PCI address map is setup that the region
of PCI address space used for MSIs differs for each PHB on the same SoC.
Instead of assuming that the address mappes to CCSRBAR 1:1 we read
PEXCSRBAR (BAR0) for the PHB that the given pci_dev is on.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds PCI IDs for MPC8569 and MPC8569E processors,
plus adds appropriate quirks for these IDs, and thus makes
PCI-E actually work on MPC8569E-MDS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The latest QE chip may have more Serial Number(SNUM)s of thread to use. We
will get the number of SNUMs from device tree by reading the new property
"fsl,qe-num-snums", and set 28 as the default number of SNUMs so that it is
compatible with the old QE chips' device trees which don't have this new
property. The macro QE_NUM_OF_SNUM is defined as the maximum number in QE
snum table which is 256.
Also we update the snum_init[] array with 18 more new SNUMs which are
confirmed to be useful on new chip.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change the RISC allocation to macros instead of enum, add function to read
the number of risc engines from the new property "fsl,qe-num-riscs" under
the qe node in dts. Add new property "fsl,qe-num-riscs" description in
qe.txt
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also, convert them to resource_size_t (which is unsigned long
on 64-bit, so it's not a change there).
We will be using these on fsl 32b to indicate the start and size
address of memory that the pci controller can actually reach - this
is needed to determine if an address requires bounce buffering. For
now, initialize them to a standard value; in the near future, the
value will be calculated based on how the inbound windows are
programmed.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Ben Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The rstcr register mapping code was written sometime ago before
of_iomap() existed. We can use it and clean up the code a bit
and get rid of one user of get_immrbase() in the process.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Before when we were setting up the irq host map for mpic we passed in
just isu_size for the size of the linear map. However, for a number of
mpic implementations we have no isu (thus pass in 0) and will end up
with a no linear map (size = 0). This causes us to always call
irq_find_mapping() from mpic_get_irq().
By moving the allocation of the host map to after we've determined the
number of sources we can actually benefit from having a linear map for
the non-isu users that covers all the interrupt sources.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The interrupt controller was not handling level interrupts correctly
such that duplicate interrupts were happening. This fixes the problem
and adds edge type interrupts which are needed in Xilinx hardware.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit b31a1d8b41 ("gianfar: Convert
gianfar to an of_platform_driver"), possibly due merge issues,
reintroduced completely unneded mpc83xx_wdt_init call, which
I removed some time ago in commit 20d38e01d4
("powerpc/fsl_soc: remove mpc83xx_wdt code").
Remove it once again.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This build failure:
arch/powerpc/sysdev/mpic.c:810: error: conflicting types for 'mpic_set_affinity'
arch/powerpc/sysdev/mpic.h:39: error: previous declaration of 'mpic_set_affinity' was here
make[2]: *** [arch/powerpc/sysdev/mpic.o] Error 1
make[2]: *** Waiting for unfinished jobs....
Triggers because the function prototype was not updated when the
function call signature got changed by:
d5dedd4: irq: change ->set_affinity() to return status
[ Impact: build fix on powerpc ]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-arch@vger.kernel.org
LKML-Reference: <49F654E9.4070809@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
according to Ingo, change set_affinity() in irq_chip should return int,
because that way we can handle failure cases in a much cleaner way, in
the genirq layer.
v2: fix two typos
[ Impact: extend API ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-arch@vger.kernel.org
LKML-Reference: <49F654E9.4070809@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The driver should pass a device that specifies internal DMA ops, but
currently NULL pointer is passed, therefore following bug appears
during boot up:
------------[ cut here ]------------
Kernel BUG at c0018a7c [verbose debug info unavailable]
Oops: Exception in kernel mode, sig: 5 [#1]
[...]
NIP [c0018a7c] fsl_rio_doorbell_init+0x34/0x60
LR [c0018a70] fsl_rio_doorbell_init+0x28/0x60
Call Trace:
[ef82bda0] [c0018a70] fsl_rio_doorbell_init+0x28/0x60 (unreliable)
[ef82bdc0] [c0019160] fsl_rio_setup+0x6b8/0x84c
[ef82be20] [c02d28ac] fsl_of_rio_rpn_probe+0x30/0x50
[ef82be40] [c0234f20] of_platform_device_probe+0x5c/0x84
[...]
---[ end trace 561bb236c800851f ]---
This patch fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (28 commits)
powerpc: Fix oops when loading modules
powerpc: Wire up preadv and pwritev
powerpc/ftrace: Fix printf format warning
powerpc/ftrace: Fix #if that should be #ifdef
powerpc: Fix ptrace compat wrapper for FPU register access
powerpc: Print information about mapping hw irqs to virtual irqs
powerpc: Correct dependency of KEXEC
powerpc: Disable VSX or current process in giveup_fpu/altivec
powerpc/pseries: Enable relay in pseries_defconfig
powerpc/pseries: Fix ibm,client-architecture comment
powerpc/pseries: Scan for all events in rtasd
powerpc/pseries: Add dispatch dispersion statistics
powerpc: Clean up some prom printouts
powerpc: Print progress of ibm,client-architecture method
powerpc: Remove duplicated #include's
powerpc/pmac: Fix internal modem IRQ on Wallstreet PowerBook
powerpc/wdrtas: Update wdrtas_get_interval to use rtas_data_buf
fsl-diu-fb: Pass the proper device for dma mapping routines
powerpc/pq2fads: Update device tree for use with device-tree-aware u-boot.
cpm_uart: Disable CPM udbg when re-initing CPM uart, even if not the console.
...
* git://git.infradead.org/mtd-2.6: (53 commits)
[MTD] struct device - replace bus_id with dev_name(), dev_set_name()
[MTD] [NOR] Fixup for Numonyx M29W128 chips
[MTD] mtdpart: Make ecc_stats more realistic.
powerpc/85xx: TQM8548: Update DTS file for multi-chip support
powerpc: NAND: FSL UPM: document new bindings
[MTD] [NAND] FSL-UPM: Add wait flags to support board/chip specific delays
[MTD] [NAND] FSL-UPM: add multi chip support
[MTD] [NOR] Add device parent info to physmap_of
[MTD] [NAND] Add support for NAND on the Socrates board
[MTD] [NAND] Add support for 4KiB pages.
[MTD] sysfs support should not depend on CONFIG_PROC_FS
[MTD] [NAND] Add parent info for CAFÉ controller
[MTD] support driver model updates
[MTD] driver model updates (part 2)
[MTD] driver model updates
[MTD] [NAND] move gen_nand's probe function to .devinit.text
[MTD] [MAPS] move sa1100 flash's probe function to .devinit.text
[MTD] fix use after free in register_mtd_blktrans
[MTD] [MAPS] Drop now unused sharpsl-flash map
[MTD] ofpart: Check name property to determine partition nodes.
...
Manually fix trivial conflict in drivers/mtd/maps/Makefile
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. This requires support for multiple GPIOs for the RNB pins.
The NAND chips are selected through address lines defined by the
FDT property "fsl,upm-addr-line-cs-offsets".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
CoreInt provides a mechansim to deliver the IRQ vector directly
into the core on an interrupt (via the SPR EPR) rather than having
to go IACK on the PIC. This is suppose to provide an improvment
in interrupt latency by reducing the time to get the IRQ vector.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
The advantages of this:
- Don't encourage legacy support;
- Less external symbols, less code to compile-in for !MPC832x_RDB
platforms.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The main purpose of this patch is to pass 'struct spi_device' to the chip
select handling routines. This is needed so that we could implement
full-fledged OpenFirmware support for this driver.
While at it, also:
- Replace two {de,activate}_cs routines by single cs_contol().
- Don't duplicate platform data callbacks in mpc83xx_spi struct.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: cleanup
It's unused, since about 1995. So remove all initialization of it in
preparation for actually removing the field.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
This patch tweaks the way some PTE bit combinations are defined, in such a
way that the 32 and 64-bit variant become almost identical and that will
make it easier to bring in a new common pte-* file for the new variant
of the Book3-E support.
The combination of bits defining access to kernel pages are now clearly
separated from the combination used by userspace and the core VM. The
resulting generated code should remain identical unless I made a mistake.
Note: While at it, I removed a non-sensical statement related to CONFIG_KGDB
in ppc_mmu_32.c which could cause kernel mappings to be user accessible when
that option is enabled. Probably something that bitrot.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit bedd30d986 ("genirq: make irqreturn_t
an enum") from the genirq tree in next-20090319 caused this new warning:
arch/powerpc/sysdev/pmi.c: In function 'pmi_of_probe':
arch/powerpc/sysdev/pmi.c:166: warning: passing argument 2 of 'request_irq' from incompatible pointer type
Change the return type of the handler from "int" to "irqreturn_t".
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Building the fs_enet driver as a modules fails because it cannot
access the global cpm2_immr symbol.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On MPC837X CPUs Dual-Role USB isn't always available (for example DR
USB pins can be muxed away to eSDHC).
U-Boot adds status = "disabled" property into the DR USB nodes to
indicate that we must not try to configure or probe Dual-Role USB,
otherwise we'll break eSDHC support on targets with MPC837X CPUs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The interrupt pending register is write 1 clear. If there are more than
one external interrupts pending at the same time, acking the first
interrupt by reading pending register then OR the corresponding bit and
write back to pending register will also clear other interrupt pending
bits. That will cause loss of interrupt.
Signed-off-by: Da Yu <dayu@datangmobile.cn>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI 2.x cells used on some 44x SoCs only let us configure the decode
for the low 32-bit of the incoming PLB addresses. The top 4 bits (this
is a 36-bit bus) are hard wired to different values depending on the
specific SoC in use. Our code used to work "by accident" until I added
support for the ISA memory holes and while at it added more validity
checking of the addresses.
This patch should bring it back to working condition. It still relies
on the device-tree being correct but that's somewhat a pre-requisite
for anything to work anyway.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
4xx chips commonly now have multiple PHBs, there is no reason to not
enable PCI domains on them. The main issue with PCI domains is X but
currently its already somewhat busted for other reasons such as the
36-bit physical address space, which I'm fixing separately.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This is a simple change to correct problems when using set_irq_type
on platforms using CPM2. This code corrects the problem on most platform
but may have issues on 8272 derived platforms for some interrupts.
On 8272 PC2 & 3 are missing and PC 23 & 29 are added, which this patch
does not address.
Signed-off-by: Paul Bilke <paul@conspiracy.net>
Reviewed-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
I noticed this doing some randconfig testing (.config below). I have
CONFIG_PM but no CONFIG_SUSPEND. Bug is against mainline.
arch/powerpc/sysdev/built-in.o: In function `ipic_suspend':
ipic.c:(.text+0x6b34): undefined reference to `fsl_deep_sleep'
make[1]: *** [.tmp_vmlinux1] Error 1
make: *** [sub-make] Error 2
Looks like #ifdef CONFIG_PM in arch/powerpc/sysdev/ipic.c should be
CONFIG_SUSPEND. d49747bdfb introduced
this.
Fix build when we have CONFIG_PM but no CONFIG_SUSPEND.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Instead of rounding the divider down, improve the baud-rate generators
accuracy by rounding to the nearest integer.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for PCI-Express controllers as found on the
newer MPC83xx chips.
The work is loosely based on the Tony Li's patch[1], but unlike the
original patch, this patch implements sliding window for the Type 1
transactions using outbound window translations, so we don't have to
ioremap the whole PCI-E configuration space.
[1] http://ozlabs.org/pipermail/linuxppc-dev/2008-January/049028.html
Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Convert arch/powerpc/ over to long long based u64:
-#ifdef __powerpc64__
-# include <asm-generic/int-l64.h>
-#else
-# include <asm-generic/int-ll64.h>
-#endif
+#include <asm-generic/int-ll64.h>
This will avoid reoccuring spurious warnings in core kernel code that
comes when people test on their own hardware. (i.e. x86 in ~98% of the
cases) This is what x86 uses and it generally helps keep 64-bit code
32-bit clean too.
[Adjusted to not impact user mode (from paulus) - sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Impact: cleanup, update to new cpumask API
Irq_desc.affinity and irq_desc.pending_mask are now cpumask_var_t's
so access to them should be using the new cpumask API.
Signed-off-by: Mike Travis <travis@sgi.com>
Provides a small speedup when accessing pefetchable ranges. To indicate
that a memory range is prefetchable, mark it in the dts file with 42000000
instead of 02000000.
A powepc pci_controller is allowed three memory ranges, any of which may be
prefetchable. However, the PCI-PCI bridge configuration space only has one
field for "non-prefetchable memory behind bridge", which has a 32 bit
address, and one field for "prefetchable memory behind bridge", which may
have a 64 bit address. These are PCI bus addresses, not CPU physical
addresses.
So really you're only allowed one memory range of each type. And if you
want the range at a PCI address above 32 bits you must make it
prefetchable.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>