The module.h header was implicitly present everywhere, so files
with no explicit include of the module infrastructure would build
anyway. We are now removing the implicit include, and so we need
to call out the module.h file that we need explicitly.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This patch adds one more check-condition for scsi_dh_alua handler. Without
this, the handler attach fails sometimes during the discovery. I have noticed
this with NetApp E-Series storage with alua mode. Also removed some
unnecessary brackets {} for consistency.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds couple more Vendor/Product IDs for RDAC.. There are no
functional changes.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The alua device handler starts the first retry after 10 seconds,
and increases it times 10 for each round.
This leads to an unnecessary delay. This patch modifies it to
start after one second, and increase by a factor of two.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For Target Portal Group IDs occupying the full 2 bytes in the
RTPG response, the following group_id check in the alua_rtpg
routine always fails in scsi_dh_alua.c:
if (h->group_id == (ucp[2] << 8) + ucp[3]) {
This causes the ALUA handler to wrongly identify the AAS of
a specified device as well as incorrectly interpreting the
supported AAS of the target as seen by the following entries
in the /var/log/messages:
"alua: port group 3ea state A supports tousna"
"alua: port group 3e9 state A supports tousna"
This is because 'ucp' is wrongly declared in alua_rtpg as
a character pointer instead of an unsigned character pointer.
Signed-off-by: Martin George <marting@netapp.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Avoid attaching a hardware handler to a device which is
already scheduled for deletion.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When activating a patch we should always update the TPGS state
as it might have changed in between.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Some device handler types are not tied to the vendor/model
but rather to a specific capability. Eg ALUA is supported
if the 'TPGS' setting in the standard inquiry is set.
This patch implements a 'match' callback for device handler
which supersedes the original vendor/model lookup and
implements the callback for the ALUA handler.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixup some kernel-doc comments to reference to the
correct function name.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Instead of issuing a standard inquiry from within the
alua device handler we can evaluate the TPGS setting from
the existing inquiry data of the sdev and save us the I/O.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
rdac hardware handler assumes that there is one-to-one relation ship
between the host and the controller w.r.t lun. IOW, it does not
support "multiple storage partitions" within a storage.
Example:
HBA1 and HBA2 see lun 0 and 1 in storage A (1)
HBA3 and HBA4 see lun 0 and 1 in storage A (2)
HBA5 and HBA6 see lun 0 and 1 in storage A (3)
luns 0 and 1 in (1), (2) and (3) are totally different.
But, rdac handler treats the lun 0s (and lun 1s) as the same when
sending a mode select to the controller, which is wrong.
This patch makes the rdac hardware handler associate HBA and the
storage w.r.t lun (and not the host itself).
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
rdac hardware handler uses "Subsystem Identifier" from C4 inquiry page
to uniquely identify a storage. The problem with that is that if any
any of the bytes are non-ascii, subsys_id will all be spaces (hex
0x20). This creates lot of problems especially when there are multiple
rdac storages are connected to the server.
Use "Storage Array Unique Identifier" from C8 inquiry page, which is the
world wide unique identifier for the storage array, to uniquely identify
the storage.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
All these are instances of
#define NAME value;
or
#define NAME(params_opt) value;
These of course fail to build when used in contexts like
if(foo $OP NAME)
while(bar $OP NAME)
and may silently generate the wrong code in contexts such as
foo = NAME + 1; /* foo = value; + 1; */
bar = NAME - 1; /* bar = value; - 1; */
baz = NAME & quux; /* baz = value; & quux; */
Reported on comp.lang.c,
Message-ID: <ab0d55fe-25e5-482b-811e-c475aa6065c3@c29g2000yqd.googlegroups.com>
Initial analysis of the dangers provided by Keith Thompson in that thread.
There are many more instances of more complicated macros having unnecessary
trailing semicolons, but this pile seems to be all of the cases of simple
values suffering from the problem. (Thus things that are likely to be found
in one of the contexts above, more complicated ones aren't.)
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (110 commits)
[SCSI] qla2xxx: Refactor call to qla2xxx_read_sfp for thermal temperature.
[SCSI] qla2xxx: Unify the read/write sfp mailbox command routines.
[SCSI] qla2xxx: Clear complete initialization control block.
[SCSI] qla2xxx: Allow an override of the registered maximum LUN.
[SCSI] qla2xxx: Add host number in reset and quiescent message logs.
[SCSI] qla2xxx: Correctly read sfp single byte mailbox register.
[SCSI] qla2xxx: Add qla82xx_rom_unlock() function.
[SCSI] qla2xxx: Log if qla82xx firmware fails to load from flash.
[SCSI] qla2xxx: Use passed in host to initialize local scsi_qla_host in queuecommand function
[SCSI] qla2xxx: Correct buffer start in edc sysfs debug print.
[SCSI] qla2xxx: Update firmware version after flash update for ISP82xx.
[SCSI] qla2xxx: Fix hang during driver unload when vport is active.
[SCSI] qla2xxx: Properly set the dsd_list_len for dsd_chaining in cmd type 6.
[SCSI] qla2xxx: Fix virtual port failing to login after chip reset.
[SCSI] qla2xxx: Fix vport delete hang when logins are outstanding.
[SCSI] hpsa: Change memset using sizeof(ptr) to sizeof(*ptr)
[SCSI] ipr: Rate limit DMA mapping errors
[SCSI] hpsa: add P2000 to list of shared SAS devices
[SCSI] hpsa: do not attempt PCI power management reset method if we know it won't work.
[SCSI] hpsa: remove superfluous sleeps around reset code
...
The SCSI ALUA handler currently fails to attach to devices
reporting an UNAVAILABLE/OFFLINE AAS. But given that an
UNAVAILABLE/OFFLINE AAS can transition to other states
like ACTIVE/OPTIMIZED, ACTIVE/NON-OPTIMIZED, etc. as per
SPC4, this ALUA handler behavior should be rectified so
as to attach to devices which also report an
UNAVAILABLE/OFFLINE AAS.
Signed-off-by: Martin George <marting@netapp.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Based on the operating modes, handler decides whether to send mode
select or not. Purpose here is to reduce io-shipping as much as
possible whenever there is an option.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Reviewed-by: Yanling Qi <yanling.qi@lsi.com>
Reviewed-by: Sudhir Dachepalli <Sudhir.Dachepalli@lis.com>
Reviewed-by: Somasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Reviewed-by: Bob Stankey <Robert.Stankey@lsi.com>
Reviewed-by: Vijay Chauhan <Vijay.Chauhan@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch detects different operating RDAC modes during the
discovery. It also collects the information about the preferred path.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Reviewed-by: Yanling Qi <yanling.qi@lsi.com>
Reviewed-by: Sudhir Dachepalli <Sudhir.Dachepalli@lis.com>
Reviewed-by: Somasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Reviewed-by: Bob Stankey <Robert.Stankey@lsi.com>
Reviewed-by: Vijay Chauhan <Vijay.Chauhan@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds definitions to support for different operating modes
for LSI rdac storage. Currently, rdac support 3 operation modes.
1. RDAC mode(legacy)
2. AVT mode
3. IOSHIP mode
These definitions are used while activating the path(rdac_activate).
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Reviewed-by: Yanling Qi <yanling.qi@lsi.com>
Reviewed-by: Sudhir Dachepalli <Sudhir.Dachepalli@lis.com>
Reviewed-by: Somasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Reviewed-by: Bob Stankey <Robert.Stankey@lsi.com>
Reviewed-by: Vijay Chauhan <Vijay.Chauhan@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Commit db422318cb ([SCSI] scsi_dh:
propagate SCSI device deletion) introduced a regression where the device
reference is not dropped prior to scsi_dh_activate's early return from
the error path.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org # 2.6.38
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch is to add Dell MD36xxf array into the RDAC handler device list.
Singed-off-by: Yanqing Liu <Yanqing_Liu@Dell.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adding MODULE_VERSION for scsi_dh_rdac. This will be helpful sometimes
to get the code level without looking at the code.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
instead of doing sizeof(struct X) it's better to do sizeof(*v) where v
is the variable pointing to struct X.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
During one of our testing, we noticed that mode select command sent
from the host did not have the lun_table updated.
Problem is root caused to the way lun table is updated. Lun table
update was done after the call to blk_rq_map_kern is made. This was
causing problem because kernel uses bounce buffer(bio_copy_kern) if
the address is not aligned. The command buffer updated after the
call(blk_rq_map_kern) was not going on the wire. Moved the code to
update the lun_table before the call to fix the problem.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: Somasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Signed-off-by: Yanling Qi <Yanling.Qi@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The use of blk_execute_rq_nowait() implies __blk_put_request() is needed
in start_stop_endio() rather than blk_put_request() --
blk_finish_request() is called with queue lock already held.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Previously we were using strncmp in order to avoid having to include
whitespace in the devlist, but this means "HSV1000" matches a device
list entry that says "HSV100", which is wrong. This patch changes
scsi_dh.c to use scsi_devinfo's matching functions instead, since they
handle these cases correctly.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently NetApp's VID/PID details in the INQUIRY response shows up as
'NETAPP' and 'LUN'. With upcoming scalable SAN ONTAP version on NetApp
controllers, the PID entry alone is being modified to 'LUN C-Mode' (to
distinguish current ONTAP LUNs from scalable ONTAP LUNs).
'LUN' would still suffice for matching 'LUN C-Mode' but best to
explicitly add these new NetApp LUNs to the device list.
Reported-by: Martin George <marting@netapp.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adds Promise VTrak devices to the ALUA device handler.
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Initialize stpg_endio() 'err' to SCSI_DH_OK and only change it to
SCSI_DH_IO accordingly. This allows the switching of target group state
to be properly reported when no error has occurred.
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The use of blk_execute_rq_nowait() implies __blk_put_request() is needed
in stpg_endio() rather than blk_put_request() -- blk_finish_request() is
called with queue lock already held.
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
submit_stpg() will always return failure so alua_activate() will report
failure via dm-multipath callback function. Even though the stpg fired
successfuly dm-multipath does not know and always fails to change the
valid path.
By returning SCSI_DH_OK we're now skipping alua_activate()'s call to
activate_complete 'fn'. But this is fine because stpg_endio() will call
it via h->callback_fn().
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently, when scsi_dh_activate() returns with an error
(e.g. SCSI_DH_NOSYS) the activate_complete callback is not called and
the error is not propagated to DM mpath.
When a SCSI device attached to a device handler is deleted, userland
processes currently performing I/O on the device will have their I/O
hang forever.
- Set SCSI_DH_NOSYS error when the handler is in the process of being
deleted (e.g. the SCSI device is in a SDEV_CANCEL or SDEV_DEL state).
- Set SCSI_DH_DEV_OFFLINED error when device is in SDEV_OFFLINE state.
- Call the activate_complete callback function directly from
scsi_dh_activate if an error has been set (when either the scsi_dh
internal data has already been deleted or is in the process of being
deleted).
The patch was tested in an iSCSI environment, RDAC H/W handler and
multipath. In the following reproduction process, dd will I/O hang
forever and the only way to release it will be to reboot the machine:
1) Perform I/O on a multipath device:
dd if=/dev/dm-0 of=/dev/zero bs=8k count=1000000 &
2) Delete all slave SCSI devices contained in the mpath device:
I) In an iSCSI environment, the easiest way to do this is by
stopping iSCSI:
/etc/init.d/iscsi stop
II) Another way to delete the devices is by applying the following
bash scriptlet:
dm_devs=$(ls /sys/block/ | grep dm- | xargs)
for dm_dev in $dm_devs; do
devices=$(ls /sys/block/$dm_dev/slaves)
for device in $devices; do
echo 1 > /sys/block/$device/device/delete
done
done
NOTE: when DM mpath's fail_path uses blk_abort_queue this scsi_dh change
isn't strictly required. However, DM mpath's call to blk_abort_queue
will soon be reverted because it has proven to be unsafe due to a race
(between blk_abort_queue and scsi_request_fn) that can lead to list
corruption. Therefore we cannot rely on blk_abort_queue via fail_path,
but even if we could this scsi_dh change is still preferrable.
Signed-off-by: Menny Hamburger <Menny_Hamburger@Dell.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For ALUA we should be handling all states, independent of whether
the mode is explicit or implicit. For 'Transitioning' we should retry
for a certain amount of time; after that we're setting the port
to 'Standby' and return SCSI_DH_RETRY to signal upper layers
a retry is in order here.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch is to add next generation of Dell iSCSI PowerVault
controller MD36xxi into RDAC device list.
Signed-off-by: Yanqing Liu <Yanqing_Liu@Dell.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
blk_get_request sets the cmd_flags, so we should not and do not
need to set them. If we did set them to a different value then
it can cause a oops in the elevator code.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This patch fixes the request setup code for mode selects. I got the fixes from
Hannes Reinecke while trying to hunt down some problems and merged it
into one patch. I am sending it because Hannes is busy with other things.
The patch fixes:
- setting of the length for mode selects.
- setting of the data direction for mode select 10.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adds IBM Power Virtual SCSI ALUA devices to the ALUA device handler.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Newer Netapp target software supports ALUA, so
this patch adds them to the scsi_dev_alua dev list.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds two new IBM storage devices which can use rdac device handlers.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Create the sysfs file, dh_state even if the new SCSI device is not
in the any of the device handler's internal lists.
Signed-Off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Make the activate function asynchronous by using blk_execute_rq_nowait()
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Make the activate function asynchronous by using blk_execute_rq_nowait()
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Batch up MODE_SELECT in rdac device handler.
LSI RDAC storage has the capability of handling mode selects for
multiple luns in a same command. Make use of that ability to send
as few MODE SELECTs as possible to the storage controller as possible.
This patch creates a work queue and queues up activate requests
when a MODE SELECT is sent down the wire. When that MODE SELECT
completes, it compiles queued up activate requests for multiple
luns into a single MODE SELECT.
This reduces the time to do failover/failback of large number of LUNS.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Make scsi_dh_activate() function asynchronous, by taking in two additional
parameters, one is the callback function and the other is the data to call
the callback function with.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The function mode_select_handle_sense returns SCSI_DH_OK even when there is a sense code which is incorrect. Removing it so that it returns SCSI_DH_IO when there is sense that is not handled by this function.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Reviewed-by: Vijay Chauhan <vijay.chauhan@lsi.com>
Reviewed-by: Bob Stankey <Robert.stankey@lsi.com>
Reviewed-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Patch to add debugging stuff for rdac device handler.
- Added a bit mask "module parameter" rdac_logging with 2 bits for each type
of logging.
- currently defined only two types of logging(failover and sense logging). Can
be enhanced later if required.
- By default only failover logging is enabled which is equivalent of current
logging.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Reviewed-by: Vijay Chauhan <vijay.chauhan@lsi.com>
Reviewed-by: Bob Stankey <Robert.stankey@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adding the code to read the debug information during initialization. This
patch collects the information about storage and controllers during
rdac_activate.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Reviewed-by: Vijay Chauhan <vijay.chauhan@lsi.com>
Reviewed-by: Bob Stankey <Robert.stankey@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Paul Gortmaker