Register each PLL and its division clocks to clock
lookup table to facilitate the clock look up for
clock consumer.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Clock on ls1088a chip takes primary clocking input from the external
SYSCLK signal. The SYSCLK input (frequency) is multiplied using
multiple phase locked loops (PLL) to create a variety of frequencies
which can then be passed to a variety of internal logic, including
cores and peripheral IP modules.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Read the enable register to determine if the clock is already in use by
the firmware. In this case avoid gating the clock.
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Fixes: 282a4e4ce5 ("platform/x86: Enable Atom PMC platform clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Drop static on a local variable, when the variable is initialized before
any possible use. Thus, the static has no benefit.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Remove unnecessary static on local variable _base_ in both functions
moxart_of_pll_clk_init() and moxart_of_apb_clk_init(). Such variables
are initialized before being used, on every execution path throughout
the mentioned functions. The statics have no benefit and, removing
them reduce the code size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see the difference in the code size. Also,
notice that the bss segment is reduced down to zero. This log is the
output of the size command, before and after the code change:
before:
text data bss dec hex filename
1724 384 128 2236 8bc drivers/clk/clk-moxart.o
after:
text data bss dec hex filename
1697 240 0 1937 791 drivers/clk/clk-moxart.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
As there is no way to actually query the hardware for the current clock
rate, now racalc_rate() just returns the last rate that was previously
set. But if the rate was not set yet, we return the bogus rate of 1000Hz.
The branch clocks have the same rate as their parent, so in this case we
just need to remove recalc_rate ops and then the core framework will handle
this automagically. The round_rate() is unused, so remove it as well.
Reported-by: Archit Taneja <architt@codeaurora.org>
Fixes: 00f64b5887 ("clk: qcom: Add support for SMD-RPM Clocks")
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fixed the signedness bug returning '(-22)' on the return type as u8 with
removing the sanity checker in clk_cpumux_get_parent() since
clk_cpumux_set_parent() always ensures validity in clk_cpumux_get_parent()
got called.
Fixes: 1e17de9049 ("clk: mediatek: add missing cpu mux causing Mediatek cpufreq can't work")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
commit e2860e1f62 ("serial: 8250_of: Add reset support")
introduced reset support for the 8250_of driver.
However it unconditionally uses the assert/deassert pair to
deassert reset on the device at probe and assert it at
remove. This does not work with systems that have a
self-deasserting reset controller, such as Gemini, that
recently added a reset controller.
As a result, the console will not probe on the Gemini with
this message:
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
of_serial: probe of 42000000.serial failed with error -524
This (-ENOTSUPP) is the error code returned by the
deassert() operation on self-deasserting reset controllers.
To work around this, implement dummy .assert() and
.deassert() operations in the Gemini combined clock and
reset controller. This fixes the issue on this system.
Cc: Joel Stanley <joel@jms.id.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-serial@vger.kernel.org
Fixes: e2860e1f62 ("serial: 8250_of: Add reset support")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Update IDT VersaClock 5 driver to support 5P49V5925. This chip has only
external clock input, four fractional dividers (FODs) and five clock
outputs (four universal clock outputs and one reference clock output at
OUT0_SELB_I2C).
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Update IDT VersaClock 5 driver to support IDT VersaClock 6 5P49V6901.
This chip has two clock inputs (external XTAL or external CLKIN), four
fractional dividers (FODs) and five clock outputs (four universal clock
outputs and one reference clock output at OUT0_SELB_I2C).
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
on Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The VersaClock 6 has an input frequency doubler between the input
clock mux and the predivider. Add new capability flag and support
for this frequency doubler block into the driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
on Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Split the VC5 clock input mux and the predivider to more accurately
model the hardware and fix the previously incorrect assumption that
both the OUT_SEL_I2CB and the PLL are fed from the predivider.
It is in fact the clock input mux output which is directly feeding
the clock into the OUT_SEL_I2CB output, while the clock input mux
output first passes through the predivider before it is fed into
the PLL.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
on Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The output buffer input mux can be configured in either of three
states -- disabled, input from FOD, input from previous output.
Once the .prepare() callback of the output buffer is called, the
output buffer input mux must be set to either input from FOD or
input from previous output, it cannot be set to Disabled anymore
or the output won't work.
Default to the input from FOD if the output buffer input mux was
Disabled and the .prepare() was called on it.
Note that we do not set the output buffer input mux back to Disabled
in the .unprepare() callback as there is no obvious benefit of doing
so. We disable the entire output buffer in the .unprepare() callback
already.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The output buffer input mux can be configured in either of three
states -- disabled, input from FOD, input from previous output.
If the output buffer input mux is set to disabled, the code in
vc5_clk_out_get_parent() would consider this an invalid setting
and warn about it, which is not necessarily the case.
In case the output buffer input mux is disabled, default to input
from FOD to have some parent and don't print the warning.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In case the initial values of the FOD registers are not configured in
the OTP or by the bootloader, it is possible that the FOD registers
will contain zeroes. The code in vc5_fod_recalc_rate() immediately
feeds the FOD divider value obtained from the FOD registers into the
div64_u64() and if the FOD divider value is zero, triggers division
by zero exception.
Check if the FOD divider value is zero and return the frequency of
the FOD output as 0 Hz if it is so. This prevents the division by
zero exception.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
AXS10X boards manages it's clocks using various PLLs. These PLL has same
dividers and corresponding control registers mapped to different addresses.
So we add one common driver for such PLLs.
Each PLL on AXS10X board consist of three dividers: IDIV, FBDIV and
ODIV. Output clock value is managed using these dividers.
We add pre-defined tables with supported rate values and appropriate
configurations of IDIV, FBDIV and ODIV for each value.
As of today we add support for PLLs that generate clock for the
following devices:
* ARC core on AXC CPU tiles.
* ARC PGU on ARC SDP Mainboard.
and more to come later.
By this patch we add support for two plls (arc core pll and pgu pll),
so we had to use two different init types: CLK_OF_DECLARE for arc core pll and
regular probing for pgu pll.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
[sboyd@codeaurora.org: Silence dubious !x & y sparse warning,
make of_axs10x_pll_clk_setup() unregister clk on failure]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pull MIPS updates from Ralf Baechle:
"Boston platform support:
- Document DT bindings
- Add CLK driver for board clocks
CM:
- Avoid per-core locking with CM3 & higher
- WARN on attempt to lock invalid VP, not BUG
CPS:
- Select CONFIG_SYS_SUPPORTS_SCHED_SMT for MIPSr6
- Prevent multi-core with dcache aliasing
- Handle cores not powering down more gracefully
- Handle spurious VP starts more gracefully
DSP:
- Add lwx & lhx missaligned access support
eBPF:
- Add MIPS support along with many supporting change to add the
required infrastructure
Generic arch code:
- Misc sysmips MIPS_ATOMIC_SET fixes
- Drop duplicate HAVE_SYSCALL_TRACEPOINTS
- Negate error syscall return in trace
- Correct forced syscall errors
- Traced negative syscalls should return -ENOSYS
- Allow samples/bpf/tracex5 to access syscall arguments for sane
traces
- Cleanup from old Kconfig options in defconfigs
- Fix PREF instruction usage by memcpy for MIPS R6
- Fix various special cases in the FPU eulation
- Fix some special cases in MIPS16e2 support
- Fix MIPS I ISA /proc/cpuinfo reporting
- Sort MIPS Kconfig alphabetically
- Fix minimum alignment requirement of IRQ stack as required by
ABI / GCC
- Fix special cases in the module loader
- Perform post-DMA cache flushes on systems with MAARs
- Probe the I6500 CPU
- Cleanup cmpxchg and add support for 1 and 2 byte operations
- Use queued read/write locks (qrwlock)
- Use queued spinlocks (qspinlock)
- Add CPU shared FTLB feature detection
- Handle tlbex-tlbp race condition
- Allow storing pgd in C0_CONTEXT for MIPSr6
- Use current_cpu_type() in m4kc_tlbp_war()
- Support Boston in the generic kernel
Generic platform:
- yamon-dt: Pull YAMON DT shim code out of SEAD-3 board
- yamon-dt: Support > 256MB of RAM
- yamon-dt: Use serial* rather than uart* aliases
- Abstract FDT fixup application
- Set RTC_ALWAYS_BCD to 0
- Add a MAINTAINERS entry
core kernel:
- qspinlock.c: include linux/prefetch.h
Loongson 3:
- Add support
Perf:
- Add I6500 support
SEAD-3:
- Remove GIC timer from DT
- Set interrupt-parent per-device, not at root node
- Fix GIC interrupt specifiers
SMP:
- Skip IPI setup if we only have a single CPU
VDSO:
- Make comment match reality
- Improvements to time code in VDSO"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (86 commits)
locking/qspinlock: Include linux/prefetch.h
MIPS: Fix MIPS I ISA /proc/cpuinfo reporting
MIPS: Fix minimum alignment requirement of IRQ stack
MIPS: generic: Support MIPS Boston development boards
MIPS: DTS: img: Don't attempt to build-in all .dtb files
clk: boston: Add a driver for MIPS Boston board clocks
dt-bindings: Document img,boston-clock binding
MIPS: Traced negative syscalls should return -ENOSYS
MIPS: Correct forced syscall errors
MIPS: Negate error syscall return in trace
MIPS: Drop duplicate HAVE_SYSCALL_TRACEPOINTS select
MIPS16e2: Provide feature overrides for non-MIPS16 systems
MIPS: MIPS16e2: Report ASE presence in /proc/cpuinfo
MIPS: MIPS16e2: Subdecode extended LWSP/SWSP instructions
MIPS: MIPS16e2: Identify ASE presence
MIPS: VDSO: Fix a mismatch between comment and preprocessor constant
MIPS: VDSO: Add implementation of gettimeofday() fallback
MIPS: VDSO: Add implementation of clock_gettime() fallback
MIPS: VDSO: Fix conversions in do_monotonic()/do_monotonic_coarse()
MIPS: Use current_cpu_type() in m4kc_tlbp_war()
...
Add a driver for the clocks provided by the MIPS Boston board from
Imagination Technologies. 2 clocks are provided - the system clock & the
CPU clock - and each is a simple fixed rate clock whose frequency can be
determined by reading a register provided by the board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16483/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The probe does a shift and mask of val without having read it from the hardware.
Fixes: 846423f967 ("clk: Add Gemini SoC clock controller")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Current implementation of scpi_clk_add just print a warning when clock
fails to register but then keep going as if nothing happened. The
provider is then registered with bogus data.
This may latter lead to an Oops in __clk_create_clk when
hlist_add_head(&clk->clks_node, &hw->core->clks) is called.
This patch fixes the issue and errors if a clock fails to register.
Fixes: cd52c2a4b5 ("clk: add support for clocks provided by SCP(System Control Processor)")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On sama5d2, VDD core maybe be cut while in suspend. This means registers
will be lost. Ensure they are saved and restored properly.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
CONFIG_COMPILE_TEST allows building a configuration without
TI_SCI_PROTOCOL, which then fails to link:
drivers/clk/keystone/sci-clk.o: In function `ti_sci_clk_probe':
sci-clk.c:(.text.ti_sci_clk_probe+0x4c): undefined reference to `devm_ti_sci_get_handle'
This makes it a hard dependency. Right now, that means we can't
actually compile-test the driver unless ARCH_KEYSTONE is set as
well, but we can fix that by allowing TI_MESSAGE_MANAGER to
be selected for COMPILE_TEST as well.
Fixes: b745c0794e ("clk: keystone: Add sci-clk driver support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Similarly to commit f1e9203e23 ("clk: samsung: Fix Exynos 5420 pinctrl
setup and clock disable failure due to domain being gated") for
Exynos5420, the Exynos4412 also requires that EPLL is not disabled.
Otherwise any access to MAUDIO block will silently halt.
This was not visible before because EPLL on Exynos4 could not be
disabled before commit 6edfa11cb3 ("clk: samsung:
Add enable/disable operation for PLL36XX clocks"). After this commit,
on Odroid U3 board one can see silent hang, usually with last (but
unrelated) messages:
[ 2.382741] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 2.405686] usb 1-3: new high-speed USB device number 3 using exynos-ehci
[ 2.419843] max77686-rtc max77686-rtc: setting system clock to 2017-06-21 17:04:13 UTC (1498064653)
Mark Exynos4 variant as also needed EPLL to be enabled all the time.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This allows the NAND driver to get the clock rate via clk_get_rate().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Cortina Systems Gemini (SL3516/CS3516) has an on-chip clock
controller that derive all clocks from a single crystal, using some
documented and some undocumented PLLs, half dividers, counters and
gates. This is a best attempt to construct a clock driver for the
clocks so at least we can gate off unused hardware and driver the
PCI bus clock.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[sboyd@codeaurora.org: Fix devm_ioremap_resource() return value
checking]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that this function is called from driver probe routines, it
needs to drop the __init marking because it isn't just called
from init code.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Cc: Anup Patel <anup.patel@broadcom.com>
Cc: Ray Jui <ray.jui@broadcom.com>
Cc: Scott Branden <scott.branden@broadcom.com>
Fixes: 654cdd3229 ("clk: bcm: Add clocks for Stingray SOC")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds support for Stingray clocks in iproc
ccf. The Stingray SOC has various plls based on iproc
pll architecture.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The patch enables CPU multiplexer clock on MT8173 SoC which fixes up
cpufreq driver fails at acquiring intermediate clock source when driver
probe is called.
Signed-off-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The patch enables CPU multiplexer clock on MT2701/MT7623 SoC which fixes
up cpufreq driver fails at acquiring intermediate clock source when driver
probe is called.
Signed-off-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds CPU multiplexer clocks which are essential for Mediatek
cpufreq driver. It would use the CPU clock multiplexer to switch to the
intermediate clock source temporarily and then wait for the primary clock
changing getting stable.
Signed-off-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If CONFIG_OF=n:
drivers/clk/renesas/renesas-cpg-mssr.c: In function ‘cpg_mssr_probe’:
drivers/clk/renesas/renesas-cpg-mssr.c:702: warning: dereferencing ‘void *’ pointer
drivers/clk/renesas/renesas-cpg-mssr.c:702: error: request for member ‘data’ in something not a structure or union
To fix this, use the of_device_get_match_data() helper, for which a
dummy version is provided if CONFIG_OF=n.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Export I2S mux clocks, so that device tree can refer to them for setting
a better parent clock for I2S work clock.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The rawnand clock gate gates two clocks, NAND_USDHC_BUS_CLK_ROOT
and NAND_CLK_ROOT. However, the gate has been in the chain of the
latter only. This does not allow to use the NAND_USDHC_BUS_CLK_ROOT
only, e.g. as required by APBH-Bridge-DMA.
Add new clocks which represent the clock after the gate, and use a
shared clock gate to correctly model the hardware.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Set PPLL2 to 2880M. With this patch, we saw better compatibility
on various 1080p HDMI monitors.
Signed-off-by: Zhong Kaihua <zhongkaihua@huawei.com>
Signed-off-by: Zheng Shaobo <zhengshaobo1@huawei.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
[sboyd@codeaurora.org: Add UL to long number to silence C90
warning]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Parent name of clk_mux_sysbus is not correct. This patch fixes it.
Signed-off-by: Chen Jun <chenjun14@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
MCLK for internal audio codec is expected to be at 9.6MHz by default.
This patch adds support to 9.6MHz to make the default case possible.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds support for the global clock controller found on
the ipq8074 based devices. This includes UART, I2C, SPI etc.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Mark an array of strings static const and remove the dereference
of a function pointer when assigning to the platform driver probe
struct member.
drivers/clk/mvebu/cp110-system-controller.c:89:12:
warning: symbol 'gate_base_names' was not declared. Should it be static?
drivers/clk/mvebu/cp110-system-controller.c:447:18:
error: cannot dereference this type
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pull improved Marvel Armada 7K/8K cp110 clk support from Gregory CLEMENT:
We got more information about the clock controllers and the clock tree
of the CP110 part that we find in the Marvell Armada 7K/8K SoCs. The
clk driver is modified accordingly from this new information.
* 'clk-cp110' of git://git.infradead.org/linux-mvebu:
clk: mvebu: cp110: add sdio clock to cp-110 system controller
clk: mvebu: cp110: introduce a new binding
clk: mvebu: cp110: do not depend anymore of the *-clock-output-names
clk: mvebu: cp110: make failure labels more meaningful
The smplsel bits for the SDMMC clock on Arria10 and Stratix10 platforms are
offset by 1 additional bit.
Add a new macro SYSMGR_SDMMC_CTRL_SET_AS10 for usage on the Arria10 and
Stratix10 platforms.
Fixes: 5611a5ba8e ("clk: socfpga: update clk.h so for Arria10 platform to use")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The timer will register into system at very early phase at kernel boot;
if timer needs to use clock, the clock should be get ready in function
of_clk_init() so later the timer driver probe can retrieve clock
successfully. This is finished in below flow on arm64:
start_kernel()
`-> time_init()
`-> of_clk_init(NULL) => register timer's clock
`-> clocksource_probe() => register timer
On Hi3660 the sp804 timer uses clock "osc32k", this clock is registered
as platform driver rather than CLK_OF_DECLARE_DRIVER method. As result,
sp804 timer probe returns failure due if cannot bind clock properly.
To fix the failure, this patch is to split crgctrl clocks into two
subsets. One part is for fixed_rate_clks which includes pre-defined
fixed rate clocks, and "osc32k" clock is in this category; So we change
their registration to CLK_OF_DECLARE_DRIVER method, as result the clocks
can be registered ahead with function of_clk_init() and timer driver can
bind timer clock successfully; the rest of the crgctrl clocks are still
registered by the probe of the platform driver.
This patch also adds checking for all crgctrl clocks registration and
print out log if any clock has failure.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This commit updates the CP110 system controller driver to add the
definition for a missing clock.
The SDIO clock is dedicated driving the SDHCI interface and its frequency
is 400MHz (2/5 of PLL source clock).
The SDIO interface should be bound to this clock and not the core clock
as in the older code.
Using the wrong clock lead to a maximum SDHCI frequency of 250 Mhz, while
the HW really supports up to 400 Mhz.
This patch also fixes the NAND clock relationship documentation.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
[gregory.clement@free-electrons.com:
- use sdio instead of emmc to name the clock]
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The initial intent when the binding of the cp110 system controller was to
have one flat node. The idea being that what is currently a clock-only
driver in drivers would become a MFD driver, exposing the clock, GPIO and
pinctrl functionality. However, after taking a step back, this would lead
to a messy binding. Indeed, a single node would be a GPIO controller,
clock controller, pinmux controller, and more.
This patch adopts a more classical solution of a top-level syscon node
with sub-nodes for the individual devices. The main benefit will be to
have each functional block associated to its own sub-node where we can
put its own properties.
The introduction of the Armada 7K/8K is still in the early stage so the
plan is to remove the old binding. However, we don't want to break the
device tree compatibility for the few devices already in the field. For
this we still keep the support of the legacy compatible string with a big
warning in the kernel about updating the device tree.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Using the *-clock-output-names property was a convenient way to have a
unique name for each clock even when there are multiple cp110 blocks
as we can find on Armada 8K.
However it has some drawbacks: the main one being a stronger link than
necessary between the driver and the device tree. For example the clock
name can't be changed, removed or moved. It is still the early stage of
introduction of the Armada 7K/8K and the hardware is still not totally
documented, especially for the clock part. By removing the use of
*-clock-output-names it will be easier to add new clocks without breaking
the compatibility.
The name of each clock is now created by using its physical address as a
prefix (as it was done for the platform device names). Thanks to this we
have an automatic way to compute a unique name.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
* Add new compatible to the meson8 clock controller for meson8b
* Add missing parents to gxbb clk81
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=0BO9
-----END PGP SIGNATURE-----
Merge tag 'meson-clk-for-4.13-2' of git://github.com/BayLibre/clk-meson into clk-next
Pull Amlogic clk driver updates from Jerome Brunet:
* Expose more clock gate on meson8 (SAR ADC, RNG, USB, SDIO, ETH)
* Add new compatible to the meson8 clock controller for meson8b
* Add missing parents to gxbb clk81
* tag 'meson-clk-for-4.13-2' of git://github.com/BayLibre/clk-meson:
clk: meson: gxbb: add all clk81 parents
clk: meson: meson8b: add compatibles for Meson8 and Meson8m2
clk: meson8b: export the ethernet gate clock
clk: meson8b: export the USB clocks
clk: meson8b: export the gate clock for the HW random number generator
clk: meson8b: export the SDIO clock
clk: meson8b: export the SAR ADC clocks
Yuantian Tang