It was supposed to have been killed on the same commit that killed the
function, e1264ebe9f, but I guess the
intel_drv.h reorganization accidentally brought it back.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds the initial infrastructure to allow a Runtime PM
implementation that sets the device to its D3 state. The patch just
adds the necessary callbacks and the initial infrastructure.
We still don't have any platform that actually uses this
infrastructure, we still don't call get/put in all the places we need
to, and we don't have any function to save/restore the state of the
registers. This is not a problem since no platform uses the code added
by this patch. We have a few people simultaneously working on runtime
PM, so this initial code could help everybody make their plans.
V2: - Move some functions to intel_pm.c
- Remove useless pm_runtime_allow() call at init
- Remove useless pm_runtime_mark_last_busy() call at get
- Use pm_runtime_get_sync() instead of 2 calls
- Add a WARN to check if we're really awake
V3: - Rebase.
V4: - Don't need to call pci_{save,restore}_state and
pci_set_power_sate, since they're already called by the PCI
layer
- Remove wrong pm_runtime_enable() call at init_runtime_pm
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't modify the packed infoframe data, so we should keep the
const qualifier in place. Just pass the buffer as 'const void *'
instead of 'const uint8_t *' and we can drop the cast entirely.
v2: Do intel_sdvo_write_infoframe() as well
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If one mode of a internal panel has more than one refresh rate, then a reduced
clock is found for the LFP (LVDS/eDP). This enables switching between low
and high frequency dynamically. Moving downclock calculation to intel_panel
so that it is common for LVDS and eDP.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we call intel_display_power_enabled() from
i915_capture_error_state() in IRQ context and then take a mutex. To fix
this add a new intel_display_power_enabled_sw() which returns the domain
state based on software tracking as opposed to reading the actual HW
state.
Since we use domain_use_count for this without locking on the reader
side make sure we increase the counter only after enabling all required
power wells and decrease it before disabling any of these power wells.
Regression introduced in
commit 1b02383464b4a915627ef3b8fd0ad7f07168c54c
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Sep 24 16:17:09 2013 +0300
drm/i915: support for multiple power wells
Note that atm we depend on the value returned by
intel_display_power_enabled_sw() in i915_capture_error_state() to avoid
unclaimed register access reports. This was never guaranteed though,
since another thread can disable the power concurrently. If this is a
problem we need another explicit way to disable the reporting during
error captures.
v2:
- remove barriers as the caller can't depend on the value
returned from i915_capture_error_state_sw() anyway (Ville)
- dump the state of pipe/transcoder power domain state (Daniel)
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in Jani's backlight rework branch. This was merged through a
separate branch to be able to sort out the Broadwell conflicts
properly before pulling it into the main development branch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prepare for being able to use the information at enable.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The backlight code has grown rather hairy, not least because the
hardware registers and bits have repeatedly been shuffled around. And
this isn't expected to get any easier with new hardware. Make things
easier for our (read: my) poor brains, and split the code up into chip
specific functions.
There should be no functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ALthough usually there's only one connector that supports backlight,
this also finds the correct connector. Before, we only updated the
connector on pipe A, which might not be the one with backlight. (This
only made a difference on BYT.)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move from dev_priv to connector->panel. We still don't allow multiple
sysfs interfaces, though.
There should be no functional changes, except for a slight reordering of
connector backlight and sysfs destroy calls. (This change happens now
that the backlight device is actually per-connector, even though the
destroy calls became per-connector earlier.)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've always felt the backlight device conditional build has been all
backwards. Make it feel right.
Gently move things towards connector based stuff while at it.
There should be no functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vlv_dpio_read/write should be describe more in PHY centric instead of
display controller centric.
Create a enum dpio_channel for channel index and enum dpio_phy for PHY
index. This should better to gather for upcoming platform.
v2: Rebase the code based on
drm/i915/vlv: Fix typo in the DPIO register define.
v3: Rename vlv_phy to dpio_phy_iosf_port and define additional macro
DPIO_PHY, and remove unrelated change. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/BYT, backlight controls a per-pipe, so when adjusting the
backlight we need to pass the correct info. So make the externally
visible backlight functions take a connector argument, which can be used
internally to figure out the pipe backlight to adjust.
v2: make connector pipe lookup check for NULL crtc (Jani)
fixup connector check in ASLE code (Jani)
v3: make sure we take the mode config lock around lookups (Daniel)
v4: fix double unlock in panel_get_brightness (Daniel)
v5: push ASLE work into a work queue (Daniel)
v6: separate ASLE work to a prep patch, rebase (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's possible that the CCK clock could run at a different rate than the
DDR clock, so use the same method to get CCK as the GMBUS code does when
calculating the new CDclk divider in the VLV display code.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similarly rename the other related functions in the power domain
interface.
Higher level driver code calling these functions knows only about power
domains, not the underlying power wells which may be different on
different platforms. Also these functions really init/cleanup/resume
power domains and only through that all related power wells, so rename
them accordingly.
Note that I left i915_{request,release}_power_well as is, since that
really changes the state only of a single power well (and is HSW
specific). It should also get a better name once we make it more
generic by controlling things through a new audio power domain.
v4:
- use intel prefix instead of i915 everywhere (Paulo)
- use a $prefix_$block_$action format (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we make sure that all power domains are enabled during driver
init and turn off unneded ones only after the first modeset. Similarly
during suspend we enable all power domains, which will remain on through
the following resume until the first modeset.
This logic is supported by intel_set_power_well() in the power domain
framework. It would be nice to simplify the API, so that we only have
get/put functions and make it more explicit on the higher level how this
"power well on during init" logic works. This will make it also easier
if in the future we want to shorten the time the power wells are on.
For this add a new device private flag tracking whether we have the
power wells on because of init/suspend and use only
intel_display_power_get()/put(). As nothing else uses
intel_set_power_well() we can remove it.
This also fixes
commit 6efdf354dd
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Oct 16 17:25:52 2013 +0300
drm/i915: enable only the needed power domains during modeset
where removing intel_set_power_well() resulted in not releasing the
reference on the power well that was taken during init and thus leaving
the power well on all the time. Regression reported by Paulo.
v2:
- move the init_power_on flag to the power_domains struct (Daniel)
v3:
- add note about this being a regression fix too (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So far the modeset code enabled all power domains if it needed any. It
wasn't a problem since HW generations so far only had one always-on
power well and one dynamic power well that can be enabled/disabled. For
domains powered by always-on power wells (panel fitter on pipe A and the
eDP transcoder) we didn't do anything, for all other domains we just
enabled the single dynamic power well.
Future HW generations will change this, as they add multiple dynamic
power wells. Support for these will be added later, this patch prepares
for those by making sure we only enable the required domains.
Note that after this change on HSW we'll enable all power domains even
if it was the domain for the panel fitter on pipe A or the eDP
transcoder. This isn't a problem since the power domain framework
already checks if the domain is on an always-on power well and doesn't
do anything in this case.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fill out the HSW watermark s/w tracking structures with the current
hardware state in intel_modeset_setup_hw_state(). This allows us to skip
the HW state readback during watermark programming and just use the values
we keep around in dev_priv->wm. Reduces the overhead of the watermark
programming quite a bit.
v2: s/init_wm/wm_get_hw_state
Remove stale comment about sprites
Make DDB partitioning readout safer
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix whitespace fail.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduce a new struct intel_pipe_wm which contains all the
watermarks for a single pipe. Use it to unify the LP0 and LP1+
watermark computations so that we can just iterate through the
watermark levels neatly and call ilk_compute_wm_level() for each.
Also add another tool ilk_wm_merge() that merges the LP1+ watermarks
from all pipes. For that, embed one intel_pipe_wm inside intel_crtc that
contains the currently valid watermarks for each pipe.
This is mainly preparatory work for pre-computing the watermarks for
each pipe and merging them at a later time. For now the merging still
happens immediately.
v2: Add some comments about level 0 DDB split and intel_wm_config
Add WARN_ON for level 0 being disabled
s/lp_wm/merged
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This file is all about the legacy fbdev support. If we want to extract
framebuffer functions, we better put those into a separate file.
Also rename functions accordingly, only two have used the intel_fb_
prefix anyway.
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Boots Just Fine (tm)!
The only glitch seems to be that at least on Fedora the boot splash
gets confused and doesn't display much at all.
And since there's no ugly console flickering anymore in between, the
flicker while switching between X servers (VT support is still enabled)
is even more jarring.
Also, I'm unsure whether we don't need to somehow kick out vgacon, now
that nothing else gets in the way. But stuff seems to work, so I
don't care. Also everything still works as well with VGA_CONSOLE=n
Also the #ifdef mess needs a bit of a cleanup, follow-up patches will
do just that.
To keep the Kconfig tidy, extract all the i915 options into its own
file.
v2:
- Rebase on top of the preliminary hw support option and the
intel_drv.h cleanup.
- Shut up warnings in i915_debugfs.c
v3: Use the right CONFIG variable, spotted by Chon Ming.
Cc: Lee, Chon Ming <chon.ming.lee@intel.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's try to avoid these confusing negated booleans.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Something already got misplaced (although it's from a patch from
before Paulo's cleanup). Move it to the right spot.
v2: Remove the line to keep a neat block, requested by Paulo.
Reported-by: Paulo Zanoni <przanoni@gmail.com>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The intel_flush_primary_plane name actually tells us which plane
we're talking about.
Also reorganize the internals a bit and add a missing POSTING_READ()
to make sure the hardware has seen the changes by the time we
return from the function.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IPS should be OK as long as one plane is enabled on the pipe, but
it does seem to cause problems when going between primary only and
sprite only.
This needs more investigations, but for now just disable IPS whenever
the primary plane is disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The conflict in intel_drv.h tripped me up a bit since a patch in dinq
moves all the functions around, but another one in drm-next removes a
single function. So I'ev figured backing this into a backmerge would
be good.
i915_dma.c is just adjacent lines changed, nothing nefarious there.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/intel_drv.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not really needed, rather just adds another place to hold
intermediate values that could go wrong, and it's not clear that the
training pattern set or training lane set should be written at this
point at all.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we encounter a situation where the CPU blocks waiting for results
from the GPU, give the GPU a kick to boost its the frequency.
This should work to reduce user interface stalls and to quickly promote
mesa to high frequencies - but the cost is that our requested frequency
stalls high (as we do not idle for long enough before rc6 to start
reducing frequencies, nor are we aggressive at down clocking an
underused GPU). However, this should be mitigated by rc6 itself powering
off the GPU when idle, and that energy use is dependent upon the workload
of the GPU in addition to its frequency (e.g. the math or sampler
functions only consume power when used). Still, this is likely to
adversely affect light workloads.
In particular, this nearly eliminates the highly noticeable wake-up lag
in animations from idle. For example, expose or workspace transitions.
(However, given the situation where we fail to downclock, our requested
frequency is almost always the maximum, except for Baytrail where we
manually downclock upon idling. This often masks the latency of
upclocking after being idle, so animations are typically smooth - at the
cost of increased power consumption.)
Stéphane raised the concern that this will punish good applications and
reward bad applications - but due to the nature of how mesa performs its
client throttling, I believe all mesa applications will be roughly
equally affected. To address this concern, and to prevent applications
like compositors from permanently boosting the RPS state, we ratelimit the
frequency of the wait-boosts each client recieves.
Unfortunately, this techinique is ineffective with Ironlake - which also
has dynamic render power states and suffers just as dramatically. For
Ironlake, the thermal/power headroom is shared with the CPU through
Intelligent Power Sharing and the intel-ips module. This leaves us with
no GPU boost frequencies available when coming out of idle, and due to
hardware limitations we cannot change the arbitration between the CPU and
GPU quickly enough to be effective.
v2: Limit each client to receiving a single boost for each active period.
Tested by QA to only marginally increase power, and to demonstrably
increase throughput in games. No latency measurements yet.
v3: Cater for front-buffer rendering with manual throttling.
v4: Tidy up.
v5: Sadly the compositor needs frequent boosts as it may never idle, but
due to its picking mechanism (using ReadPixels) may require frequent
waits. Those waits, along with the waits for the vrefresh swap, conspire
to keep the GPU at low frequencies despite the interactive latency. To
overcome this we ditch the one-boost-per-active-period and just ratelimit
the number of wait-boosts each client can receive.
Reported-and-tested-by: Paul Neumann <paul104x@yahoo.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68716
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Stéphane Marchesin <stephane.marchesin@gmail.com>
Cc: Owen Taylor <otaylor@redhat.com>
Cc: "Meng, Mengmeng" <mengmeng.meng@intel.com>
Cc: "Zhuang, Lena" <lena.zhuang@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: No extern for function prototypes in headers.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
struct drm_mode_display now has a separate crtc_ version of the clock to
be used when we're talking about the timings given to the harwadre (was
far as the mode is concerned).
This commit is really the result of a git grep adjusted_mode.*clock and
replacing those by adjusted_mode.crtc_clock. No functional change.
v2: Rebased on drm-intel-queued-next
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since I already reorganized the header file, Daniel requested me to
remove those keywords. It seems "checkpath.pl --strict" also doesn't
like "extern" on header files.
At least now we're consistent :)
Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These functions were added before the final PC8 implementation, and
their callers moved to intel_display.c during the code review.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And move it so it doesn't need a forward declaration.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also move it to the top of the file so we can remove the forward
declaration.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel complained that we keep adding stuff to the bottom of the file,
so we constantly have conflicts. So reorganize everything and split
them file-by-file, also sorting the files in alphabetical order. This
way, patches touching different files will have a smaller chance of
conflicting. Of course, this commit will conflict with everybody on
the list :)
Also remove a few useless comments and make some things fit into 80
lines.
v2: - Conflict with intel_ddi_get_config
Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Call intel_ddi_get_config() to get the pipe_bpp settings from
DDI.
The sync polarity settings from DDI are irrelevant for CRT
output, so override them with data from the ADPA register.
v2: Extract intel_crt_get_flags()
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69691
Tested-by: Qingshuai Tian <qingshuai.tian@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And the gratious overallocation of crtcs. Seems to go back to the ums
days of yonder ...
We also still need it to make the fbdev emulation happy, but I don't
think there's really a need. Especially since the current fbdev
emulation doesn't actually support cloning.
v2: Use sizeof(*pointer) pattern (Jani).
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSQMORAAoJEHm+PkMAQRiGj14H/1bjhtfNjPdX7MVQAzA+WpwX
s7h1IQu2Si9S5S1lBiM2sBTOssVcmfheO9x4yqm7JNOD1RnssWKOM3q+zVOLstwd
GD3gluJPeraD5EyYSqEJ9ILPQ3gbxb4wOlT0Z291TW6E8XhLRr0RTOJPksRsgvLH
Ckm9uJh6ArS6ZXfXiaDQfd+xHAQJkUfW6nMSA0g9ZO9C6KIDRvcbUmrY3m4HhfIk
mK0TXCBs+AXGDIjTEB8JgIQL/5y1Qn0c4R+2uTU/4YWwyLvJTV1e44kGoleukMMT
6Pw/TNlUEN161dbSaqCyF3sfXHDYQ5valycI2PDgitMtPSxbzsU1VDizS8+daRg=
=lEmF
-----END PGP SIGNATURE-----
Merge tag 'v3.12-rc2' into drm-intel-next
Backmerge Linux 3.12-rc2 to prep for a bunch of -next patches:
- Header cleanup in intel_drv.h, both changed in -fixes and my current
-next pile.
- Cursor handling cleanup for -next which depends upon the cursor
handling fix merged into -rc2.
All just trivial conflicts of the "changed adjacent lines" type:
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_drv.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add APIs to get/put power well references for specific purposes.
v2: Split the i915_request change to another patch
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reorganize the internal i915_request power well handling to use the
reference count just like everyone else. This way all we need to do is
check the reference count and we know whether the power well needs to be
enabled of disabled.
v2: Split he intel_display_power_{get,put} change to another patch.
Add intel_resume_power_well() to make sure we enable the power
well on resume
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Determine the need for double wide mode already in compute_config
stage as we need that information to figure out if horizontal
coordinates need to be adjusted.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to clarify the purpose of requested_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather that mess about with hdisplay/vdisplay from requested_mode, add
explicit pipe src size information to pipe config.
Now requested_mode is only really relevant for dvo/sdvo output timings.
For everything else either adjusted_mode or pipe src size should be
used.
In many places where we end up using pipe source size, we should
actually use the primary plane size, but we don't currently store
that information explicitly. As long as we treat primaries as full
screen only, we can get away with this. Eventually when we move
primaries over to drm_plane, we need to fix it all up.
v2: Add a comment to explain what pipe_src_{w,h} are
Add a note about primary planes to commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move intel_crtc_active() to intel_display.c and make it available
elsewhere as well.
intel_edp_psr_match_conditions() already has one open coded copy,
so replace that one with a call to intel_crtc_active().
v2: Copy paste a big comment from danvet's mail explaining
when we can ditch the extra checks
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that adjusted_mode.clock no longer contains the pixel_multiplier, we
can kill the get_clock() callback and instead do the clock readout
in get_pipe_config().
Also i9xx_crtc_clock_get() can now extract the frequency of the PCH
DPLL, so use it to populate port_clock accurately for PCH encoders.
For DP in port A the encoder is still responsible for filling in
port_clock. The FDI adjusted_mode.clock extraction is kept in place
for some extra sanity checking, but we no longer need to pretend it's
also the port_clock.
In the encoder get_config() functions fill out adjusted_mode.clock
based on port_clock and other details such as the DP M/N values,
HDMI 12bpc and SDVO pixel_multiplier. For PCH encoders we will then
do an extra sanity check to make sure the dotclock we derived from
the FDI configuratiuon matches the one we derive from port_clock.
DVO doesn't exist on PCH platforms, so it doesn't need to anything
but assign adjusted_mode.clock=port_clock. And DDI is HSW only, so
none of the changes apply there.
v2: Use hdmi_reg color format to detect 12bpc HDMI case
v3: Set adjusted_mode.clock for LVDS too
v4: Rename ironlake_crtc_clock_get to ironlake_pch_clock_get,
eliminate the useless link_freq variable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Extract the code to calculate the dotclock from the link clock and M/N
values into a new function from ironlake_crtc_clock_get().
The new function can be used to calculate the dotclock for both FDI and
DP cases.
Also simplify the code a bit along the way.
v2: Don't forget about non-pch encoders in ironlake_crtc_clock_get()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add functions to read out the CPU and PCH transcoder M/N values,
and use them to fill out the pipe config dp_m_n information. And
while at it populate has_dp_encoder too.
Also refactor ironlake_get_fdi_m_n_config() to simply call the new
intel_cpu_transcoder_get_m_n() function.
v2: Remember the DDI
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It would be easier if adjusted_mode.clock would be the pipe pixel clock,
and it actually is, except for the cases where pixel_multiplier > 1.
So let's change intel_sdvo to use port_clock as the multiplied clock,
and then we can leave adjusted_mode.clock as pipe pixel clock.
v2: Improve port_clock documentation
Rebased on top of SDVO pixel_multiplier fixes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Passing the appropriate crtc to intel_update_watermarks() should help
in avoiding needless work in the future.
v2: Avoid clash with internal 'crtc' variable in some wm functions
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni