STMicroelectronics NFC NCI chips family is extending
with the new ST21NFCC using the AMS AS39230 RF booster.
The st21nfcb driver is relevant for this solution and
might be with future products.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to prevent any NFC feature when NFC is disable and
to save power, (down to 4uA) put the CLF in hibernate mode
with RF deactivated.
Add the equivalent to enable the NFC feature when initiating
the st21nfcb driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When st21nfcb is disabled, the irq line may remain active
while no data are available, flooding the system with
irrelevant i2c transaction.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The powered flag can be set from the ndlc_open and ndlc_close layer.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Removing st21nfcb may need to execute some specific commands before
stopping the ndlc state machine.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On st21nfcb, nci proprietary commands are available to run
specific chip operations (for example: power management)
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When closing st21nfcb driver, flag ST21NFCB_NCI_RUNNING can be cleared
only once the ndlc and the transport (i2c or spi) layers are released.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to release the st21nfcb properly close the ndlc
layer first.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ndlc_remove already calls st21nfcb_nci_i2c_disable and
phy->powered is already set to 0.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Once the data is sent, we need to preserve the full frame for
the ndlc state machine. If the NDLC ACK is not received in time,
the ndlc layer will resend the same frame.
Having the header byte pulled will corrupt the frame.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since ndev->driver_data is allocated by devm_kzalloc(), we do not
need the inappropriate kfree to free it in driver's remove function.
Freeing will trigger when driver unloads.
Cc: stable@vger.kernel.org
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*()
functions) which appeared in v3.17-rc1, the gpiod_get* functions
take an additional parameter that allows to specify direction and
initial value for output.
Use this to simplify the driver. Furthermore this is one caller less
that stops us making the flags argument to gpiod_get*() mandatory.
While touching this also do some minor coding style fixes.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In microread_i2c_irq_thread_fn 'client' set but not used
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
CONFIG_DYNAMIC_DEBUG is the right toggle to enable pr_debug().
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current versions of the trf7970a has an erratum where it returns
an extra byte in the response to 'Read Multiple Block' (RMB) commands.
This command is issued to Type 5 tags (i.e., ISO/IEC 15693 tags) by
the neard daemon.
To handle this, define a new Device Tree property,
't5t-rmb-extra-byte-quirk', which indicates that the associated
trf7970a device has this erratum. The trf7970a device driver
will then ensure that the response length to RMB commands is
reduced by one byte (for devices with the erratum).
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When GPIO is not enabled we hit this kind of warning:
drivers/nfc/nxp-nci/i2c.c: In function 'nxp_nci_i2c_acpi_config':
drivers/nfc/nxp-nci/i2c.c:320:2: error: implicit declaration of function 'devm_gpiod_get_index' [-Werror=implicit-function-declaration]
gpiod_en = devm_gpiod_get_index(&client->dev, NULL, 2);
This is fixed by explicitely including gpio/consumer.h.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A previous commit, c93b76b34b ("mei: bus: report also uuid in module
alias") caused a build error as I missed applying a needed patch to add
some macros to uapi/linux/uuid.h. Instead of those additional macros,
change the mei code to use the existing uuid structure directly.
Fixes: c93b76b34b
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. mei_nfc_hci_hdr and mei_nfc_hdr are just the same thing so drop one
2. use mei_nfc_hdr structure as the member of the command and the reply
instead of replicating all header fields.
3. dump the header for easier debugging
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
move nfc logic to mei_phy module, we prefer as much as
possible not to deal with a particualr client protocol
in the mei generic infrasutcutre
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to automate modules matching add device uuid
which is reported in client enumeration, keep also
the name that is needed in for nfc distinguishing radio vendor
Report mei:name:uuid
Cc: linux-api@vger.kernel.org
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing terminating newlines to nfc_info and nfc_err
to avoid possible interleaving from other messages.
Miscellanea:
o typo fix of "unknonwn" in message
o remove unnecessary OOM messages as there's a generic dump_stack()
o realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In that case, the firmware work will never be scheduled, will
never complete and thus the firmware will never be released.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It request_firmware returns 0, the request succeeded and the
firmware pointer is valid. No need to check for it.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add comments about HCI EVT_TRANSACTION in order to make the code
understandable by other readers.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add comments about HCI EVT_TRANSACTION in order to make the code
understandable by other readers.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
st21nfca_get_iso14443_3_uid gate parameter name is incorrect
and should be uid.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
st21nfca_get_iso14443_3_uid() does not correctly copy the uid from
uid_skb->data to its gate parameter. "gate = uid_skb->data;" only
puts a pointer to uid_skb->data to the local variable gate.
This means that in st21nfca_hci_target_from_gate() the content
of "u8 uid[NFC_NFCID1_MAXSIZE]" local variable is never initialized
before being used in memcpy(target->nfcid1, uid, len).
Fix this by replacing the local variable assignment with a memcpy.
This was found by compiling Linux with
"gcc -Wunused-but-set-parameter".
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
i2c_master_send may return many negative values different than
-EREMOTEIO.
In case an i2c transaction is NACK'ed, on raspberry pi B+
kernel 3.18, -EIO is generated instead.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In case the hci session is successfully initialized we never
release the nci_core_conn_create dest_params.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add a module to the NXP-NCI driver to support NFC controllers with an
I2C control interface, such as the NPC100.
Signed-off-by: Clément Perrochaud <clement.perrochaud@effinnov.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for NXP NCI NFC controllers such as the NPC100 or PN7150
families.
Signed-off-by: Clément Perrochaud <clement.perrochaud@effinnov.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFCEE_DISCOVER_CMD is a specified NCI command used to discover
NFCEE IDs.
Move nci_nfcee_discover() call to nci_discover_se() in order to
guarantee:
- NFCEE_DISCOVER_CMD run when the NCI state machine is initialized
- NFCEE_DISCOVER_CMD is not run in case there is not discover_se
hook defined by a NFC device driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
conn_info is currently allocated only after nfcee_discovery_ntf
which is not generic enough for logical connection other than
NFCEE. The corresponding conn_info is now created in
nci_core_conn_create_rsp().
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current implementation limits nci_core_conn_create_req()
to only manage NCI_DESTINATION_NFCEE.
Add new parameters to nci_core_conn_create() to support all
destination types described in the NCI specification.
Because there are some parameters with variable size dynamic
buffer allocation is needed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The transaction notifies the host (DH) that an action
is required to manage a specific Secure Element application.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The transaction notifies the host (DH) that an action
is required to manage a specific Secure Element application.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The st21nfcb chipset has 3 SWP (Single Wire Protocol) lines and
supports up to 3 secure elements (UICC/eSE and µSD in the future).
Some st21nfcb firmware does not support the nci command
nci_nfcee_mode_set(NCI_NFCEE_DISABLE). For this reason, we assume
2 secures elements are always present (UICC and eSE).
They will be added to the SE list once successfully activated and
they will be available only after running through enable_se
handler or when the poll in listen mode is started.
During initialization, the white_list will be always set assuming
both UICC & eSE are present.
On eSE activation, the ATR bytes are fetched to build the command
exchange timeout.
The se_io hook will allow to transfer data over SWP. 2 kind of
events may appear data is sent over:
- ST21NFCB_EVT_TRANSMIT_DATA when receiving an apdu answer
- ST21NFCB_EVT_WTX_REQUEST when the secure element needs more time
than expected to process a command. If this timeout expires, we
send a software reset, and then a hardware one if it still fails.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently there is no support for ACPI.
This patch uses the following configuration:
- Device id: NXP5440
- Pin mapping:
- 0 IRQ pin
- 1 enable pin
- 2 firmware pin
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
gpio_set_value was replaced with gpio_set_value_cansleep in order
to allow GPIO access that may sleep. This is particularelly useful
when GPIO is accessed using busses like I2C, SPI, USB
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
st21nfca has 1 physical SWP line and can support up to 2 secure elements
(UICC & eSE) thanks to an external switch managed with a gpio.
The platform integrator needs to specify thanks to 2 initialization
properties, uicc-present and ese-present, if it is suppose to have uicc
and/or ese. Of course if the platform does not have an external switch,
only one kind of secure element can be supported. Those parameters are
under platform integrator responsibilities.
During initialization, the white_list will be set according to those
parameters.
The discovery_se function will assume a secure element is physically
present according to uicc-present and ese-present values and will add it
to the secure element list. On ese activation, the atr is retrieved to
calculate a command exchange timeout based on the first atr(TB) value.
The se_io will allow to transfer data over SWP. 2 kind of events may appear
after a data is sent over:
- ST21NFCA_EVT_TRANSMIT_DATA when receiving an apdu answer
- ST21NFCA_EVT_WTX_REQUEST when the secure element needs more time than
expected to compute a command. If this timeout expired, a first recovery
tentative consist to send a simple software reset proprietary command.
If this tentative still fail, a second recovery tentative consist to send
a hardware reset proprietary command.
This function is only relevant for eSE like secure element.
This patch also change the way a pipe is referenced. There can be
different pipe connected to the same gate with different host destination
(ex: CONNECTIVITY). In order to keep host information every pipe are
reference with a tuple (gate, host). In order to reduce changes, we are
keeping unchanged the way a gate is addressed on the Terminal Host.
However, this is working because we consider the apdu reader gate is only
present on the eSE slot also the connectivity gate cannot give a reliable
value; it will give the latest stored pipe value.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When the platform with CONFIG_ST21NFCB_I2C=y without any st21nfcb component
physically connected a:
"Unable to handle kernel NULL pointer dereference at virtual address" may
show up at driver initialization phase.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix some memory leaks after some nfc_hci_get_param calls.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove unnecessary memory allocation message already shown by devm_kzalloc.
This remove a warning when running scripts/checkpatch.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
skb_pipe_list and skb_pipe_info are allocated in nfc_hci_send_cmd.
alloc_skb on those buffer are then useless.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Do not insert in send queue the skb that contains unknown Packet Control
Byte
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
kfree_skb(skb) in st21nfca_hci_event_received is never reach.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ndlc pointer got allocated with devm_kzalloc in ndlc_probe function.
This gives this error message:
drivers/nfc/st21nfcb/ndlc.c:296:1-6: WARNING: invalid free of devm_ allocated data.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Other drivers are following the following compatible string format for dts:
s/_/-/
Because some devices may still use the previous string, the new corrected
string is added to the of_device_id table.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Other drivers are following the following compatible string format for dts:
s/_/-/
Because some devices may still use the previous string, the new corrected
string is added to the of_device_id table.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in drivers/nfc/trf7970a.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Report error returned by devm_gpio_request_one instead of -ENODEV.
Reported-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Report error returned by devm_gpio_request_one or
st21nfca_hci_platform_init instead of -ENODEV.
Reported-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
- pr_info in st21nfcb_nci_i2c_disable is not necessary
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In ndlc_probe function we initialize timers. They are not started.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As many event with the same id can come from several gates,
it will be easier to manage each of them by gate.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
- phy->gpio_irq is never done out of the request resources.
- irq_of_parse_and_map is already done in the i2c core so client->irq is
already set when entering in st21nfcb_hci_i2c_of_request_resources
- In case of static platform configuration client->irq can be set directly.
- It simplifies the code a bit.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When CONFIG_OF is define add of_st21nfcb_i2c_match to
MODULE_DEVICE_TABLE
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
- phy->gpio_irq is never done out of the request resources.
- irq_of_parse_and_map is already done in the i2c core so client->irq is
already set when entering in st21nfca_hci_i2c_of_request_resources
- In case of static platform configuration client->irq can be set directly
- It simplifies the code a bit.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When CONFIG_OF is define add of_st21nfca_i2c_match to
MODULE_DEVICE_TABLE.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is a specific implementation, <asm/unaligned.h> is the
multiplexer that has the arch-specific knowledge of which
of the implementations needs to be used, so include that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
John W. Linville says:
====================
pull request: wireless-next 2014-10-03
Please pull tihs batch of updates intended for the 3.18 stream!
For the iwlwifi bits, Emmanuel says:
"I have here a few things that depend on the latest mac80211's changes:
RRM, TPC, Quiet Period etc... Eyal keeps improving our rate control
and we have a new device ID. This last patch should probably have
gone to wireless.git, but at that stage, I preferred to send it to
-next and CC stable."
For (most of) the Atheros bits, Kalle says:
"The only new feature is testmode support from me. Ben added a new method
to crash the firmware with an assert for debug purposes. As usual, we
have lots of smaller fixes from Michal. Matteo fixed a Kconfig
dependency with debugfs. I fixed some warnings recently added to
checkpatch."
For the NFC bits, Samuel says:
"We've had major updates for TI and ST Microelectronics drivers, and a
few NCI related changes.
For TI's trf7970a driver:
- Target mode support for trf7970a
- Suspend/resume support for trf7970a
- DT properties additions to handle different quirks
- A bunch of fixes for smartphone IOP related issues
For ST Microelectronics' ST21NFCA and ST21NFCB drivers:
- ISO15693 support for st21nfcb
- checkpatch and sparse related warning fixes
- Code cleanups and a few minor fixes
Finally, Marvell added ISO15693 support to the NCI stack, together with a
couple of NCI fixes."
For the Bluetooth bits, Johan says:
"This 3.18 pull request replaces the one I did on Monday ("bluetooth-next
2014-09-22", which hasn't been pulled yet). The additions since the last
request are:
- SCO connection fix for devices not supporting eSCO
- Cleanups regarding the SCO establishment logic
- Remove unnecessary return value from logging functions
- Header compression fix for 6lowpan
- Cleanups to the ieee802154/mrf24j40 driver
Here's a copy from previous request that this one replaces:
'
Here are some more patches for 3.18. They include various fixes to the
btusb HCI driver, a fix for LE SMP, as well as adding Jukka to the
MAINTAINERS file for generic 6LoWPAN (as requested by Alexander Aring).
I've held on to this pull request a bit since we were waiting for a SCO
related fix to get sorted out first. However, since the merge window is
getting closer I decided not to wait for it. If we do get the fix sorted
out there'll probably be a second small pull request later this week.
'"
And,
"Unless 3.17 gets delayed this will probably be our last -next pull request for
3.18. We've got:
- New Marvell hardware supportr
- Multicast support for 6lowpan
- Several of 6lowpan fixes & cleanups
- Fix for a (false-positive) lockdep warning in L2CAP
- Minor btusb cleanup"
On top of all that comes the usual sort of updates to ath5k, ath9k,
ath10k, brcmfmac, mwifiex, and wil6210. This time around there are
also a number of rtlwifi updates to enable some new hardware and
to reconcile the in-kernel drivers with some newer releases of the
Realtek vendor drivers. Also of note is some device tree work for
the bcma bus.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
skb is already freed in st21nfca_tx_work and was freed also in
st21nfca_im_send_psl_req.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
"skb" can be NULL here but it can't be an ERR_PTR:
- IS_ERR(NULL) return false and skb migth be NULL.
- skb cannot be a ERR_PTR as nfc_hci_send_cmd_async it never using such cast.
!skb is more appropriate at those places.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In case we are not able to read out the NDLC/NCI header, we do not
consider this as an issue and we will give a later chance.
The NDLC layer will handle errors thanks to its internal timers.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for ISO/IEC 15693 RF technology and Type 5 tags.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In NFC Forum NCI specification, some RF Protocol values are
reserved for proprietary use (from 0x80 to 0xfe).
Some CLF vendor may need to use one value within this range
for specific technology.
Furthermore, some CLF may not becompliant with NFC Froum NCI
specification 2.0 and therefore will not support RF Protocol
value 0x06 for PROTOCOL_T5T as mention in a draft specification
and in a recent push.
Adding get_rf_protocol handle to the nci_ops structure will
help to set the correct technology to target.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
T2 was never started when sending a command.
Start it when sending a command for the first attempt
and stop it once we receive the answer.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On st21nfcb the irq line might be kept to active state because of other
interfaces activity. This may generate i2c read tentative resulting in
i2c NACK.
This fix will currently let NDLC upper layer to decide when it is relevent
to signal to the physical layer when the chip as muted.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch fix a previous patch introduce by commit 0a91e8ac24
It is actually fixing a double free mistake in all st21nfca_tm_* function.
We decide to return directly in case of successful execution because skb
got already freed. In st21nfca_tm_recv_dep_req it got freed by nfc_tm_data_received.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
After a unsuccessful call to nfc_hci_send_event the skb was not
freed and might lead to memory leak.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix few conding style issue such as useless line return or tab.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The recently added _trf7970a_tg_listen() routine
has some return paths that don't unlock the mutex
that is locked when the routine is entered. Fix
this by always unlocking the mutex before returning.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Recent changes to trf7970a_irq() added a couple return
paths that don't unlock the mutex that is locked when
the routine is entered. Fix this by ensuring the mutex
is always unlocked before returning.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There is no need to initialize the 'ret' variable
in trf7970a_resume().
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The trf7970a_suspend() routine always returns
zero so don't use a local return variable to
hold the return value. This fixes up a smatch
warning.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove some headers as they are:
- not relevent for st21nfcb.
- called multiple times for no reason: example st21nfcb.h already include
ndlc.h.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
scripts/checkpatch.pl -f drivers/nfc/st21nfca.c is throwing the following:
WARNING: else is not generally useful after a break or return
#866: FILE: drivers/nfc/st21nfca/st21nfca.c:866:
+ return 0;
+ } else {
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Align every macros on the same column.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Clean up st21nfca.h macros and move the one only used in st21nfca.c.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When retrying to read the NCI header, the CLF might not be
available the first time. However it may not be successful
the second time and this may cause an error in the function.
Enforce the retrieve data length is as expected.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
gb_len in st21nfca_tm_send_atr_res can be negative. Not checking for
that could lead to a potential kernel oops.
We now make sure that atr_req->length > sizeof(struct st21nfca_atr_req)
to avoid such situation.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
skb is already verified to be not null from the below hci layer.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On top of st21nfca_im_recv_atr_res_cb and st21nfca_im_recv_dep_res_cb a
condition if (err != 0) is present. Because err is never modified in the
code err will always be 0 at the end.
The condition can be removed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
nfcid3 is based on sensf_res value. target->sensf is never NULL
as it is a table.
Check the sensf_res_len instead to make sure sensf_res is set or not.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove a useless new line in nfc_err call.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If dev_num >= ST21NFCA_NUM_DEVICES, the driver was returning an incorrect
success return code.
Once dev_num is set, it was not stated as busy.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In case of an error during driver probe, info pointer was freed with kfree.
No need to free anything when using devm_kzalloc.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove a uselss new line in nfc_err call.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Simplify the code a bit as mention by Axel Lin in a previous patch for
st21nfca.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixing scripts/checkpatch.pl error "code indent should use tabs where possible" in:
- i2c.c in st21nfcb_nci_irq_thread_fn function.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixing "sparse: cast to restricted __be32" message when building with
make C=1 CF=-D__CHECK_ENDIAN__
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This simplifies the code a bit.
Acked-by: Christophe RICARD <christophe-h.ricard@st.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The .owner member of struct device_driver is assigned THIS_MODULE twice.
Introduced by:
commit c44cb2edd0
("NFC: dts: st21nfca: Add device-tree (Open Firmware) support to st21nfca")
Acked-by: Christophe RICARD <christophe-h.ricard@st.com>
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In the previous makefile 2 modules were generated for CONFIG_NFC_ST21NFCA
(st21nfca.ko and st21nfca_dep.ko). Merge both of them into st21nfca_hci.ko
and fix a potential depmod dependency cycle, similar to the one we saw
on st21nfcb:
depmod: WARNING: found 6 modules in dependency cycles!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/drivers/nfc/st21nfcb/st21nfcb.ko
in dependency cycle!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/drivers/nfc/st21nfcb/ndlc.ko
in dependency cycle!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/net/rfkill/rfkill.ko in
dependency cycle!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/net/nfc/nfc.ko in
dependency cycle!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/net/nfc/nci/nci.ko in
dependency cycle!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/lib/crc-ccitt.ko in
dependency cycle!
./scripts/depmod.sh: line 57: 23387 Segmentation fault (core
dumped) "$DEPMOD" "$@" "$KERNELRELEASE" $SYMBOL_PREFIX
make: *** [_modinst_post] Error 139
Reported-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add the ability to detect the mode (i.e., RF technology)
used by the initiator. The RF technology that was
detected can be retrieved by calling the 'tg_get_rf_tech'
driver hook.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add target mode support to the trf7970a
NFC driver. This effectively enables full
Peer-to-Peer support.
To handle changing framing between sending
a response frame and receiving the subsequent
request frame, most of the framing changes
take effect in the interrupt handler and not
in trf7970a_tg_config_framing().
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The digital layer can try to send a command with a
timeout value of zero (e.g., digital_tg_send_psl_res().
The zero value is used as a flag to indicate that
the driver should not expect a response. To handle
this, the driver sets an internal timer because it
should still get an interrupt with the TX bit set
in the IRQ Status Register. When it gets that
interrupt, it returns a return value of '0'.
If it doesn't get the interrupt before timing out,
it returns ETIMEDOUT as usual.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some paths leave a timer still running when
trf7970a_send_err_upstream() is called. This
can cause a timeout to occur in a subsequent
transaction making it fail. Fix this by ensuring
there is no timer running before sending an error
upstream.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently, the trf7970a driver blindly turns on its
RF field when configuring its framing. This isn't
a good idea if there is already a device generating
an RF field. Instead, check if there is already an
RF field present before turning on this device's RF
field and, if there is, return EBUSY.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When trf7970a_init() initializes the trf7970a it
implicitly turns off the RF transmitter. Track
this by clearing the TRF7970A_CHIP_STATUS_RF_ON
bit in the cached trf->chip_status_ctrl.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Don't try to turn off of RF transmitter is its
already off.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rename trf7970a_config_rf_tech() and trf7970a_config_framing()
to trf7970a_in_config_rf_tech() and trf7970a_in_config_framing(),
respectively to avoid confusion when target support is added.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The trf7970a should be given at least 1 ms to
completely initialize after the 'Software Init'
and 'Idle' commands have been issued.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add system suspend/resume support by gracefully
shutting things down when suspending and bringing
the device back to full power when resuming.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Encapsulate the code to start up and gracefully
shutdown the driver and trf7970a device. Doing
this makes adding system suspend/resume support
easier and the resulting code cleaner.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current code assumes that CONFIG_PM_RUNTIME
is always defined so it won't power up the trf7970a
when it isn't enabled. Fix this by moving the power
up/down code from the pm_runtime_resume/suspend
routines into their own routines and calling the
power up function from the probe routine. This
ensures the device is powered up even when
CONFIG_PM_RUNTIME is not defined.
In order to not power on/off a device that is
already powered on/off, create a new state to
indicate that the power is off (TRF7970A_ST_PWR_OFF).
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rename the 'TRF7970A_ST_OFF' state to 'TRF7970A_ST_RF_OFF'
to make it clear that this state means that the RF is
off and not the entire device.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
trf7970a_switch_rf_on() is currently a void function
but turning on the RF could fail so it should return
a return code. That return code should also be
propagated back to the entity that initiated the
action.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Depending on the interrupt status value given by the
trf7970a, the driver may not know when a receive operation
is complete. To handle this, the driver waits for a period
of time in case the trf7970a interrupts it again indicating
there are more RX data in the FIFO. It is possible that the
timeout will occur when there are RX data in the FIFO but
before the trf7970a has generated an interrupt to tell the
driver about it. Handle this by calling trf7970a_drain_fifo()
(instead of trf7970a_send_upstream() which just passes up the
data gathered to far) to check if there are more data in the
FIFO. If so, gather that data into the receive buffer. If
not, pass the data collected so far upstream as before.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Receiving an interrupt whose Interrupt Status Register
value has only the SRX bit set is supposed to mean that
all of the data from the tag has been received. That
turns out to not be true so we need to reread the FIFO
Status Register to tell if there are any new bytes in
the FIFO. If there are, continue receiving them; if
there aren't, assume that the receive is complete and
pass the data up.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Commit 4dd836e46c ("NFC: trf7970a: Reset FIFO when
'End of TX' Interrupt Occurs") fixes the issue that
it was meant to fix but adds the unfortunate side
effect of causing the driver to report an error
when the TX low-watermark level is passed during
transmits. This can be fixed by checking whether
the IRQ status indicates that the low-watermark
has been passed when transmitting. If it has been
passed and the FIFO is empty, then its safe to reset
the FIFO. Otherwise, silently continue since another
TX interrupt will be generated and the FIFO will be
reset then.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Handle the case where trf7970a_fill_fifo() is
called but there is no room in the FIFO for
more TX data. When this happens, wait for
another interrupt indicating that there is
now space (and set a timer in case that
interrupt never occurs).
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When refilling the FIFO with more TX data (using a new
SPI transaction), the driver must prefix the TX data with
a write to the FIFO I/O Register. This tells the trf7970a
that the following data is destined for the FIFO so it can
be transmitted.
To accomplish this, the driver cannot simply push the
prefix data just before the next set of TX data that
is to be transmitted because that will overwrite part
of the TX data provided by the digital layer. Instead,
separate the prefix data and the TX data when calling
trf7970a_transmit(). trf7970a_transmit() can then send
the prefix and TX data from different memory locations
with one spi_sync() operation. This also means that
the driver doesn't require any skb "tx_headroom" as
provided by the digital layer (see
nfc_digital_allocate_device() and digital_skb_alloc()).
Also ensure that the prefix is of type 'u8' and not
'char'.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It is no longer necessary to reset the FIFO and
read the 'RSSI Levels and Oscillator Status Register'
so remove that code.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The trf7970a occasionally generates spurious interrupts
which can confuse the driver. To help alleviate this,
clear any interrupts by reading the 'IRQ Status Register'
before starting a new transaction.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some of the timeout values used in the driver
are not long enough to handle worst-case scenarios
so they need to be recalculated.
The time to wait for the FIFO to drain past the
low-watermark is now 20 ms because it can take
around 14.35 ms to send 95 bytes (127 bytes in
full FIFO minus 32 bytes where the low-watermark
interrupt will fire). 95 bytes will take around
14.35 ms at 6.62 kbps (the lowest supported bit
rate used by ISO/IEC 15693) so 20 ms should be a
safe value.
The time to wait before issuing an EOF to complete
an ISO/IEC 15693 write or lock command is 40 ms--
20 ms to drain the FIFO and another 20 ms to ensure
the wait is long enough before sending an EOF.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When turning on the RF field, the driver must wait
an RF-technology-specific amount of time (known as
the guard time) before modulating the field.
Currently, the driver waits 5 ms but that is too
short for NFCF and too long for ISO/IEC 15693.
Fix this by determining the guard time when the
RF technology is set and delaying that amount
of time when turning on the RF field.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently, the trf7970a is reset & initialized only
when the pm_runtime resume hook is called. Instead,
initialize it every time the RF is enabled to ensure
that the trf7970a is quiesced and in a known state
before being set up for another RF technology.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently, support for providing the external
SYS_CLK signal on pin 27 is not supported so
turn it off by writing to the 'Modulator and
SYS_CLK Control' register immediately after
reset.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There is no need to sleep for 1-2 ms before
transmitting a new command.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Despite what the manual says, the FIFO size
on the trf7970a is really 127 bytes so make
the code respect that.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Overflow bit in the 'FIFO Status Register' has
proven to be untrustworthy so ignore it.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
To more efficiently handle long continuous reads,
use spi_sync() instead of spi_write_then_read().
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Call spi_setup() to configure SPI communication
with the trf7970a. This will ensure that the
correct SPI parameters are used.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently, the digital layer 'tg_listen_mdaa'
hook is not used and it isn't necessary to have
a stub routine so remove it.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
of_property_read_u32() does not take a reference
to the specified OF node so don't call of_node_put()
in trf7970a_get_autosuspend_delay().
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Smatch says that skb->data is untrusted so we need to check to make sure
that the memcpy() doesn't overflow.
Fixes: cfad1ba871 ('NFC: Initial support for Inside Secure microread')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Make the labels for the two gpio enable lines
more user friendly by prefixing them with the
driver name.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A bug has been discovered in the trf7970a where it
will generate an RF field even in passive target
mode when EN2 is asserted. To work around this,
add support for the 'en2-rf-quirk' device tree
property which indicates that EN2 must remain low.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The quirk indicating whether the trf7970a has
the "IRQ Status Read" erratum or not is currently
implemented using the 'driver_data' member of the
'spi_device_id' structure. That requires the
driver to be modified to turn the quirk off when
a version of the trf7970a that doesn't have the
erratum is being used. To fix that, create a
new device tree property called
'irq-status-read-quirk' that indicates that the
trf7970a being used has the erratum.
While at it, rename 'TRF7970A_QUIRK_IRQ_STATUS_READ_ERRATA'
to 'TRF7970A_QUIRK_IRQ_STATUS_READ' to make it
less of an eyesore.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The trf7970a driver uses the voltage from the
power/regulator subsystem to determine what the
voltage on the VIN pin is. Normally, this is
the right thing to do but sometimes the board
that the trf7970a is on may change the voltage.
This is the case for the trf7970atb board from
Texas Instruments where it boosts the VIN voltage
from 3.3V to 5V (see http://www.ti.com/tool/trf7970atb).
To handle this, add support for the 'vin-voltage-override'
device tree property which overrides the voltage value
given by the regulator subsystem. When the DT property
is not present, the value from the regulator subsystem
is used.
The value of 'vin-voltage-override' is in uVolts.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Support for Initiator and Target mode with ISO18092 commands support:
- ATR_REQ/ATR_RES
- PSL_REQ/PSL_RES
- DEP_REQ/DEP_RES
Work based on net/nfc/digital_dep.c.
st21nfca is using:
- Gate reader F for P2P in initiator mode.
- Gate card F for P2P in target mode.
Felica tag and p2p are differentiated with NFCID2.
When starting with 01FE it is acting in p2p mode.
On complete_target_discovered on ST21NFCA_RF_READER_F_GATE
supported_protocols is set to NFC_PROTO_NFC_DEP_MASK
for P2P.
Tested against: Nexus S, Galaxy S2, Galaxy S3, Galaxy S3 Mini,
Nexus 4 & Nexus 5.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Send DM_DISCONNECT command to disconnect Terminal Host from the HCI network.
- The persistent states of the terminal host pipes, including registry values,
are not modifies. Therefore, there is no NVRAM update to disconnect the
terminal host.
- The terminal host RF card gates are disabled which means that there will be no event
related to card RF gates until communication has been restored.
- The terminal host RF reader request is reset so the RF reader polling for terminal
host is disabled.
To restore the communication, the terminal host can send any HCI command or event.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A DEP_RES with a SUPERVISOR PDU can be up to 16 bytes long.
In order to avoid useless read during p2p, extend first read
sequence to 16 and reduce third sequence to 12 to keep same
total on the full sequence.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A start of frame is 7E 00 not only 7E. Make sure the first read sequence is
starting with 7E 00.
For example: 7E FF FF FF FF is as a correct crc but it is a bad frame.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In case no data are retrieve through i2c or one specific case is not handled.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add driver for STMicroelectronics ST21NFCB NFC controller.
ST21NFCB is using NCI protocol and a proprietary low level transport
protocol called NDLC used on top.
NDLC:
The protocol defines 2 types of frame:
- One type carrying NCI data (referred as DATAFRAME frames).
- One type carrying protocol information used for flow control and error
control mechanisms (referred as SUPERVISOR frames).
After each frame transmission to the NFC controller, the device host
SHALL waitfor an ACK (SUPERVISOR frame) reception before sending a
new frame.
The NFC controller MAY send a frame at anytime to the device host.
The NFC controller MAY send a specific WAIT supervisor frame to indicate
to device host that a NCI data packet has been received but that it could
take significant time before the NFC controller sends an ACK and thus
allows next data reception.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the Felica protocol and Type 3 tags.
Both 212 and 424 kbps are supported.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds support for ISO-DEP protocol over NFC-B rf technology
by adding NFC_PROTO_ISO14443_B to the supported protocols and an entry
for framing configuration.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for ISO/IEC 15693 RF technology and Type 5 tags.
ISO15963 is using proprietary gate 12.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In case anybody uses previous patchset with the CLF, add a check to make sure
missing pipe are created.
st21nfca returns its pipe list in the creation order (most recent latest).
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add functions to recover hardware resources from the device-tree
when not provided by the platform data.
Based on pn544 devicetree implementation
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When a bad frame is detected for a bad crc.
We were reallocating and loosing the previous frame pointer.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Stabilize communication by using a mutex.
This avoids running a write transaction during a read retry or a read
transaction during a write retry.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A frame starts with ST21NFCA_SOF_EOF(0x7e) + 0x00.
A frame ends with ST21NFCA_SOF_EOF(0x7e).
It is possible that the i2c macrocell is stopped for other
communication interfaces with highest priority(RF or SWP).
This can be seen with some 0xFF data at the end of a received shdlc buffer.
If this happen we need to discard the frame because the CLF will repeat it.
In order to push accurate data to hci layer, we add the following fix:
- Instead of looking for the first 0x7e in the frame, check that the last
received byte is 0x7e.
- Check that the first frame reception block start with start of
frame(0x7e 0x00). If not, clear the buffer.
- Check that the next frame reception block do not start with start of
frame(0x7e). If so, clear the buffer.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There is no byte stuffing when data are stored in skb.
TAILROOM is 2 byte crc + 1 byte eof.
st21nfca_hci_remove_len_crc was doing an incorrect operation on
the TAILROOM data.
If shdlc timer T2 is triggered, it will request to send the same data.
Before every hci data was lost after st21nfca_hci_remove_len_crc.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Byte stuffing was not correctly removed after a i2c read operation.
This was causing improper crc calculation when byte stuffing was
applied to more than 1 byte.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Change in st21nfca_hci_platform_init in order to handle in a better way the
internal reboot command.
Once the reboot is completed, the driver expect to receive a 0x7e filled
buffer.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove struct st21nfca_i2c_phy* as this parameter can be retrieve
through i2c_get_clientdata(client)
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
st21nfca_hci_probe return 0 in case of successful call and a different
value in any other cases.
There is no need to check for st21nfca_hci_probe return as this will be
checked after st21nfca_hci_i2c_probe is completed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
wait_tab variable is already global and may create conflicts.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixing "sparse: cast to restricted __be16" message when building with
make C=1 CF=-D__CHECK_ENDIAN__
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixes a null pointer exception occurring when the IRQ request in
pn544_hci_i2c_probe fails and no platform data is available.
Signed-off-by: Clément Perrochaud <clement.perrochaud@nxp.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now that the NFC digital layer has support for the ISO/IEC 14443-B
protocol and type 4B tags, add the corresponding support to the
trf7970a driver.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The trf7970a driver currently uses a fixed autosuspend delay of 30 seconds.
To enable users to customize the delay as they see fit, add support for the
new 'autosuspend-delay' DTS property (part of the nfc node) which can
override the default 30 seconds.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
trf7970a_switch_rf_on() no longer returns anything other than 0 so make
it void and clean up the code that checks for errors when its called.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add pm_runtime support by moving the code that enables the trf7970a to
the pm_runtime hook routines. The pm_runtime 'autosuspend' feature is
used so that the device isn't disabled until at least 30 seconds have
passed since trf7970a_switch_rf_off() was last called.
The result is that when trf7970a_switch_rf_on() is called, the device
will be enabled and initialized (if it isn't already). When
trf7970a_switch_rf_off() is called, it will turn off the RF immediately
but leave the device enabled for at least 30 seconds.
If 30 seconds have passed and the pm_runtime facility decides to suspend
the driver, the device will be disabled then.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The NFC digital layer calls the 'switch_rf' hook to turn the RF on before
it configures the RF technology and framing. There is potential to confuse
a tag doing it this way so don't enable the RF until the RF technology and
initial framing have been configured.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently, the trf7970a driver assumes that the Vin voltage is 5V when
it writes to the 'Chip Status Control' register. That may not be correct
so use the regulator facility to get the Vin voltage and set the VRS5_3
bit correctly when writing to that register.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently the driver writes the same value to the 'Modulator and SYS_CLK
Control' register no matter what RF technology is being used. That works
for now but new RF technologies (e.g., ISO/IEC 14443-B) will require
different values to be written to that register. To support this, add a
member to the trf7970a structure which is set by the RF technology handling
code and used by the framing code when it writes to that register.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Writing to the 'ISO Control' register may cause the contents of the
'Modulator and SYS_CLK Control' register to change so be sure to write
to 'Modulator and SYS_CLK Control' after writing to 'ISO Control'.
Note that writing to the 'Modulator and SYS_CLK Control' register
shouldn't be necessary at all according to the trf790a manual but testing
shows that it is necessary.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current code always writes to the 'ISO Control' register when the
RF framing is set. That's not necessary since the register's value
doesn't always change. Instead, only write to it when its value is
actually being changed.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Sometimes after sending a frame there is tx data leftover in the FIFO
which the driver will think is part of the receive frame. That data can
be cleared when an 'End of TX' interrupt is received by issuing the
'FIFO Reset' command.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Due to a trf7970a erratum, the 'NFC Target Detection Level' register
(0x18) must be cleared after power-up.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Only initiate the abort command process when there is an active command.
If the abort process were started and there wasn't an active command
then the next command issued by the digital layer would be incorrectly
aborted.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
After further testing periods of ~16 ms have been observed
between interrupts indicating that there is receive data in
the FIFO. To accomodate that, increase the time the driver
waits before deciding there is no more data to receive to
20 ms. The macro that represents that delay is
'TRF7970A_WAIT_FOR_RX_DATA_TIMEOUT'.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add functions to recover hardware resources from the device-tree when not
provided by the platform data.
Signed-off-by: Clément Perrochaud <clement.perrochaud@nxp.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This implementation rely on the ST21NFCA_DEVICE_MGNT_GATE and
ST21NFCA_DM_GETINFO proprietary gates commands.
First we are retrieving a pipe list available on the CLF with the
ST21NFCA_DM_GETINFO_PIPE_LIST parameter. A gate<->pipe table match
is done with ST21NFCA_DM_GETINFO_PIPE_INFO for each pipe.
If the pipe is created and open, we fill st21nfca_gates table.
If the pipe is create but closed or is not created we keep the gate
with NFC_HCI_INVALID_PIPE.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add driver for STMicroelectronics ST21NFCA NFC controller.
ST21NFCA is using HCI protocol, shdlc as LLC layer & I2C as
communication protocol.
Adding support for Reader/Writer mode with Tag type 1/2/3/4 A & B.
It is using proprietary gate 15 for ISO14443-3 such as type 1 &
type 2 tags. It is using proprietary gate 14 for type F tags.
ST21NFCA_DEVICE_MGNT_GATE gives access to proprietary CLF configuration.
Standard gate for ISO14443-4 A (13) & B (11) are also used.
ST21NFCA specific mecanism:
One particular point to notice for the data handling is that frame
does not contain any length value. Therefore the i2c part of this driver
is managing the reception with a read length sequence until the end of
frame (0x7e) is reached.
In order to avoid conflict between sof & eof a mecanism
called byte stuffing concist of an escape byte (0x7d) insertion before
special byte (0x7e, 0x7d). The special byte is then xored with 0x20.
In this driver, When data are available in the CLF, the interrupt
gpio is driven to active state and triggered an interrupt.
Once the i2c_master_recv start, the interrupt gpio is driven to idle
state until its complete. If the frame is incomplete or data are still
available, interrupts will be triggered again.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for ISO/IEC 15693 RF technology and Type 5 tags.
Note that Type 5 tags used to be referred to as Type V tags.
CC: Erick Macias <emacias@ti.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for Type 4A Tags which includes
supporting the underlying ISO/IEC 14443-A
protocol.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add a driver for the Texas Instruments TRF7970a RFID/NFC/15693
transceiver. The driver currently supports ISO/IEC 14443 Type 2
tags only (MIFARE Ultralight and Ultralight C but not Classic).
CC: Erick Macias <emacias@ti.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for ISO-DEP protocol over NFC-A rf technology. The
port100 already supports NFC-A and ATS request and response for type 4A
tags are handled at digital level. This patch adds NFC_PROTO_ISO14443
to the supported protocols and an entry for framing configuration which
is the same as NFC-A standard frame with CRC handling.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The arrays for protocols and rf techs must define a number of entries
corresponding to their maximum possible index values.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
PN544 C3 firmwares already contain the command frames to be sent, but as
they may exceed the i2c maximum payload, we need to fragment them into
secure chunks and send them through the secure write command.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Different pn544 hardware variant may use different commands to download
new firmwares. The C2 does a regular firmware download while the C3 uses
a more secure protocol.
As a consequence we need to pass the hardware variant from the HCI SW
version command reply down to the pn544 i2c layer, in order to use the
right protocol at run time.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch fixes memory leaks in the error paths of
nfcmrvl_nci_register_dev() routine.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Marvell nfc device provides support for external coexistance
control. It allows Device Host to inhibit the NFCC from polling
when required by asserting a GPIO pin. A second pin allows the
DH to have feedback on the current NFCC state.
The required configuration for this feature is done in setup
handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
port100_probe() calls usb_get_dev(), but there is no usb_put_dev()
in port100_disconnect(). The patch adds one.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some ACR122 firmwares seem to send 0 length data frames. Before using
that length as a data index, we check that it's not 0. If it is we
report the frame as being invalid.
Reported-by: Arthur Taylor <arthur@advancedtelematic.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some of the EEPROM configurations that are assigned by the PN544 driver
are set by the firmware and should not be modified by the driver. Others
are certain user mode configurations that are currently getting set to values
that shouldn't necessarily be dictated by the driver. This patch changes
most user and system mode configurations to the firmware defaults.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Using kfree_skb() instead of kfree() for struct sk_buff
Signed-off-by: Salil Kapur <salilkapur93@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: linux-wireless@vger.kernel.org
CC: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
CC: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements the target NFC digital operations tg_configure_hw(),
tg_listen(), tg_listen_mdaa(), and tg_send_cmd().
The target mode supports NFC-A technology at 106kbits/s and NFC-F
technologies at 212 and 424kbits/s.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Cc: Stephen Tiedemann <stephen.tiedemann@gmail.com>
Tested-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch implements the initiator NFC operations in_configure_hw()
and in_send_cmd(). It also implements the switch_rf() operation.
The initiator mode supports NFC-A technology at 106kbits/s and NFC-F
technologies at 212 and 424kbits/s.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Cc: Stephen Tiedemann <stephen.tiedemann@gmail.com>
Tested-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch implements the command handling mechanism. The digital stack
serializes all commands sent to the driver. This means that the digital
stack waits for the reply of the current command before sending a new
one. So there is no command queue managed at driver level.
All Port-100 commands are asynchronous. If the command has been sent
successfully to the device, it replies with an ACK frame. Then the
command response is received (or actually no-response in case of
timeout or error) and a command complete work on the system workqueue
is responsible for sending the response (or the error) back to the
digital stack.
The digital stack requires some commands to be synchronous, mainly
hardware configuration ones. These commands use the asynchronous
command path but are made synchronous by using a completion object.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Cc: Stephen Tiedemann <stephen.tiedemann@gmail.com>
Tested-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for the Sony NFC USB dongle RC-S380, based on the
Port-100 chip. This dongle is an analog frontend and does not implement
the digital layer. This driver uses the nfc_digital module which is an
implementation of the NFC Digital Protocol stack.
This patch is a skeleton. It only registers the dongle against the NFC
digital protocol stack. All NFC digital operation functions are stubbed
out.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Cc: Stephen Tiedemann <stephen.tiedemann@gmail.com>
Tested-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In target mode, when we want to send frames larger than the max length
(PN533_CMD_DATAEXCH_DATA_MAXLEN), we have to split the frame in smaller
chunks and send them, using a specific working queue, with the TgSetMetaData
command. TgSetMetaData sets his own MI bit in the PFB.
The last chunk is sent using the TgSetData command.
Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This code processes, for Target Mode, incoming fragmented frames.
If the MI bit is present, we start a working queue to grab and aggregate
all the parts (using TmGetData between each parts). On the last one, as
there's no more MI bit, we jump on the usual behavior.
Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The fragmentation routine (used to split big frames) could be used in
target or initiator mode (TgSetMetaData vs InDataExchange), but the
MI/TG bytes are not needed in target mode (TgSetMetaData), so we
add a check on the mode
Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Local symbols used only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Driver core sets driver data to NULL upon failure or remove.
Cc: Ilan Elias <ilane@ti.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If we start the polling loop from a listening cycle, we need to start
the corresponding timer as well.
This bug showed up after commit dfccd0f5 as it was impossible to start
from a listening cycle before it.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to improve active devices detection, we send an ATR_REQ between
each passive detection cycle. Without this algorithm, Android 4.3 based
devices running the Broadcom stack are hardly detected.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use standardized styles to minimize coding defects.
Always use nfc_<level> where feasible.
Add \n to formats where appropriate.
Typo "it it" correction.
Add #define pr_fmt where appropriate.
Remove function tracing logging messages.
Remove OOM messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use a more standard kernel style macro logging name.
Standardize the spacing of the "NFC: " prefix.
Add \n to uses, remove from macro.
Fix the defective uses that already had a \n.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use the generic kernel function instead of a home-grown
one that does the same thing.
Add \n to uses not at the macro. Don't add \n where
the nfc_dev_dbg macro mistakenly had them already.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
To enable the UICC secure element, we first enable the UICC gate list in
order for the SE to be able to use all RF technologies.
For the embedded SE, we just turn the eSE default mode to ON.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For the SWP secure element, we send the proprietary SELF_TEST_SWP
command and check the response.
For the WI secure element, we simply try to switch to the default
embedded SE mode. If that works, it means we have an embedded SE.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The pn544 can enter a firmware update mode where firmware blobs can be
pushed through the i2c line and flashed on the target.
A special command allows to verify that blobs are correctly flashed and
this is what we do for every downloaded firmware blob.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The firmware operation callback is passed by the physical layer to the
hci driver during probe. All the driver does is to store it and call it
when the fw_upload hci ops is invoked.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is in preparation for pn544-i2c firmware download feature, where we
need to know if we're in regular or firmware upload mode.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
By not always starting the polling loop from the same modulation, we
avoid entering infinite loops where devices exporting 2 targets (on 2
different modulations) get the same target activated over and over.
If this target is not readable (e.g. a wallet emulating a tag), we will
stay in an error loop for ever.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It seems that some pn533 firmwares go belly up when being asked to send
poll frames too frequently. Adding a 10ms delay between each of them
calm the chip down and prevent it from crashing.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The extended information frame are sent by PN533 to exchange frames
larger than 255 bytes. These extended frame are very close from the
standard ones except for the header size length. On each incoming
frame, we set the correct header length, and we do that only for the
standard pn533 chipsets as the acr122 does not seem to support extended
frames properly.
Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On sending large frames (size > 262), we split it in multiple chunks and
send them asynchronously with MI bit.
Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Extended Information frames are slightly different from standard frames
as they can (theorically) handle datas up tu 64kB. PN533 firmware only
supports packet data up to 265 (incl. TFI byte)
This kind of frame are used when the pn533 wants to exchange more than
255 bytes, and this patch handles the reception of such frames.
Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The AUTO RFCA bit forbids the pn533 chipset to turn its radio on
whenever an external field is present.
Without this bit set, some devices seems to get over flood by the
pn533 rf field and thus become hardly detectable.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
p2p devices must be able to support 424 kbps, so we should always select
that bitrate in initiator mode.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
By turning the radio off after each failed polling try, we dramatically
improve the pn533 polling loop efficiency.
Without this fix, all Android phones running the broadcom NFC stack are
almost never detected.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
By using the standard setting for the regular pn533 dongles, we no
longer wait for ever for an ATR_RES. Without this, a failing ATR_REQ
will put the hardware into a busy loop, constantly waiting for an
ATR_RES.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch fixes 3 sparse warnings:
nfcsim.c:63:25: sparse: symbol 'wq' was not declared.
nfcsim.c:484:12: sparse: symbol 'nfcsim_init' was not declared.
nfcsim.c:525:13: sparse: symbol 'nfcsim_exit' was not declared.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
This driver declares two virtual NFC devices supporting NFC-DEP protocol.
An LLCP connection can be established between them and all packets sent
from one device is sent back to the other, acting as loopback devices.
Once established, the LLCP link can be disconnected by disabling the target
device (with rfkill, nfctool, or neard disable-adapter test script).
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Instead of dumping ACR122 frames as errors, we use the print_hex_dump()
dynamic debug APIs.
We also print an accurate IC version, as the ACR122 is pn532 based.
Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Supported secure elements are typically found during a discovery process
initiated when the NFC controller is up and running. For a given NFC
chipset there can be many configurations (embedded SE or not, with or
without a SIM card wired to the NFC controller SWP interface, etc...) and
thus driver code will never know before hand which SEs are available.
So we remove this field, it will be replaced by a real SE discovery
mechanism.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When using NFC-F we should copy the NFCID2 buffer that we got from
SENSF_RES through the ATR_REQ NFCID3 buffer. Not doing so violates
NFC Forum digital requirement #189.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
skb->dev is used for carrying a net_device pointer and not
an nci_dev pointer.
Remove usage of skb-dev to carry nci_dev and replace it by parameter
in nci_recv_frame(), nci_send_frame() and driver send() functions.
NfcWilink driver is also updated to use those functions.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix to return -ENOMEM in the nfc device alloc error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There is no builtin command for driver to check the presence of
Felica and Jewel device, it is more reasonable for the userspace
daemon neard to build seperate commands to check the presence of
the card.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFCID2 is defined as the first 2 manufacturer ID (IDm) bytes.
NFC DEP (NFC peer to peer) devices Type-F NFCID2 must start with
0x01fe according to the NFC Digital Specification.
By checking those first 2 bytes we send the right command either to the
reader gate when NFCID2 != 0x1fe (The NFC tag case) or to the NFCIP1 gate
when seeing an NFC DEP device (The NFC peer to peer case).
Without this fix, Felica (Type F) tags are not properly detected with this
driver.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The callback registration starts a waiting read, so it needs to be fired
everytime the device is enabled. Otherwise following writes will never get
an answer back.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the new mei_phy NFC driver API, the pn544 MEI physical layer is
minimal and similar to the microread one.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This isolates the common code that is required to use an mei bus nfc
device from an NFC HCI drivers. This prepares for future drivers for
NFC chips connected behind an Intel Management Engine controller.
The microread_mei HCI driver is also modified to use that common code.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard