On some machines (currently only the Toshiba Tecra A11 is known), the GPU
locks up when modeset is forced on LID open. This patch adds a new DMI
blacklist and omits modesetting for all matches.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15550
Signed-off-by: Thomas Bächler <thomas@archlinux.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fix error from the last pull request. Making sure we shut the panel off
is more correct and saves power.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: add pipe A force quirks to i915 driver
drm/i915: Fix panel fitting regression since 734b4157
drm/i915: fix deadlock in fb teardown
drm/i915: don't free non-existent compressed llb on ILK+
agp/intel: Use the correct mask to detect i830 aperture size.
drm/i915: disable FBC when more than one pipe is active
drm/i915: Use the correct scanout alignment for fbcon.
drm/i915: make sure eDP panel is turned on
drm/i915: add PANEL_UNLOCK_REGS definition
drm/i915: Make G4X-style PLL search more permissive
drm/i915: Clear any existing dither mode prior to enabling spatial dithering
drm/i915: handle shared framebuffers when flipping
drm/i915: Explosion following OOM in do_execbuffer.
gpu/drm/i915: Add a blacklist to omit modeset on LID open
Ported over from the old UMS list. Unfortunately they're still
necessary especially on older laptop platforms.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=22126.
Tested-by: Xavier <shiningxc@gmail.com>
Tested-by: Diego Escalante Urrelo <diegoe@gnome.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The crtc mode fixup is run after the encoders adjust the mode to fit on
their output, so don't reset the mode!
Fixes:
Bug 29057 - display corruption under 800x600 on netbook
(1024x600) with 'Full Aspect' scaling
https://bugs.freedesktop.org/show_bug.cgi?id=29057
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Xun Fang <xunx.fang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
At module unload time we'll tear down the fbdev state. We do so under
the struct mutex, so we shouldn't try to use the unlocked variant of
the GEM object unreference function or we may deadlock.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We should only free the compressed llb if we allocated it in the first
place otherwise we'll panic at unload time.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We're really supposed to do this to avoid trouble with underflows when
multiple planes are active.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=26987.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: fangxun <xunx.fang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This fixes a potential modesetting error during boot with plymouth on
Broadwater and Crestline introduced with 9df47c. The framebuffer was
hard-coding an alignment of 64K, but the modesetting code required the
documented alignment of 128K. The result was that we would attempt to
unbind the pinned fbcon buffer, triggering an ERROR and ultimately
failing the mode change.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
When enabling the eDP port, we need to make sure the panel is turned on
after training the link. If we don't, it likely won't come back after
suspend or may not come up at all.
For unknown reasons, unlocking the panel regs before initiating a power
on sequence is necessary. There are known bugs in the PCH panel
sequencing logic, apparently this is one possible workaround.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=28739.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: "Paulo J. S. Silva" <pjssilva@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In some cases, unlocking the panel regs is safe and can help us avoid a
flickery, full mode set sequence. So define the unlock key and use it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes an Ironlake laptop with a 68.940MHz 1280x800 panel and 120MHz SSC
reference clock.
More generally, the 0.488% tolerance used before is just too tight to
reliably find a PLL setting. I extracted the search algorithm and
modified it to find the dot clocks with maximum error over the valid
range for the given output type:
http://people.freedesktop.org/~ajax/intel_g4x_find_best_pll.c
This gave:
Worst dotclock for Ironlake DAC refclk is 350000kHz (error 0.00571)
Worst dotclock for Ironlake SL-LVDS refclk is 102321kHz (error 0.00524)
Worst dotclock for Ironlake DL-LVDS refclk is 219642kHz (error 0.00488)
Worst dotclock for Ironlake SL-LVDS SSC refclk is 84374kHz (error 0.00529)
Worst dotclock for Ironlake DL-LVDS SSC refclk is 183035kHz (error 0.00488)
Worst dotclock for G4X SDVO refclk is 267600kHz (error 0.00448)
Worst dotclock for G4X HDMI refclk is 334400kHz (error 0.00478)
Worst dotclock for G4X SL-LVDS refclk is 95571kHz (error 0.00449)
Worst dotclock for G4X DL-LVDS refclk is 224000kHz (error 0.00510)
Signed-off-by: Adam Jackson <ajax@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
We cannot the initial configuration set by the BIOS not to have a dither
mode enabled which conflicts with our enabling the Spatial Temporal 1
dither mode for PCH. In particular, the BIOS may either enable temporal
dithering or the Spatial Temporal 2 with the result that we enable pure
temporal dithering. Temporal dithering looks bad and is perceived as a
flicker.
Fixes:
Bug 29248 - [Arrandale] Annoying flicker on internal panel, goes away
after suspend to RAM
https://bugs.freedesktop.org/show_bug.cgi?id=29248
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
If a framebuffer is shared across CRTCs, the x,y position of one of them
is likely to be something other than the origin (e.g. for extended
desktop configs). So calculate the offset at flip time so such
configurations can work.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=28518.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Thomas M. <tmezzadra@gmail.com>
Tested-by: fangxun <xunx.fang@intel.com>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/r600: fix possible NULL pointer derefernce
drm/radeon/kms: add quirk for ASUS HD 3600 board
include/linux/vgaarb.h: add missing part of include guard
drm/nouveau: Fix crashes during fbcon init on single head cards.
drm/nouveau: fix pcirom vbios shadow breakage from acpi rom patch
drm/radeon/kms: fix shared ddc harder
drm/i915: enable low power render writes on GEN3 hardware.
drm/i915: Define MI_ARB_STATE bits
vmwgfx: return -EFAULT if copy_to_user fails
fb: handle allocation failure in alloc_apertures()
drm: radeon: check kzalloc() result
drm/ttm: Fix build on architectures without AGP
drm/radeon/kms: fix gtt MC base alignment on rs4xx/rs690/rs740 asics
drm/radeon/kms: fix possible mis-detection of sideport on rs690/rs740
drm/radeon/kms: fix legacy tv-out pal mode
A lot of 945GMs have had stability issues for a long time, this manifested as X hangs, blitter engine hangs, and lots of crashes.
one such report is at:
https://bugs.freedesktop.org/show_bug.cgi?id=20560
along with numerous distro bugzillas.
This only took a week of digging and hair ripping to figure out.
Tracked down and tested on a 945GM Lenovo T60,
previously running
x11perf -copypixwin500
or
x11perf -copywinpix500
repeatedly would cause the GPU to wedge within 4 or 5 tries, with random busy bits set.
After this patch no hangs were observed.
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The i915 memory arbiter has a register full of configuration
bits which are currently not defined in the driver header file.
Signed-off-by: Keith Packard <keithp@keithp.com>
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current shrinker implementation requires the registered callback
to have global state to work from. This makes it difficult to shrink
caches that are not global (e.g. per-filesystem caches). Pass the shrinker
structure to the callback so that users can embed the shrinker structure
in the context the shrinker needs to operate on and get back to it in the
callback via container_of().
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The hibernate issues that got fixed in commit 985b823b91 ("drm/i915:
fix hibernation since i915 self-reclaim fixes") turn out to have been
incomplete. Vefa Bicakci tested lots of hibernate cycles, and without
the __GFP_RECLAIMABLE flag the system eventually fails to resume.
With the flag added, Vefa can apparently hibernate forever (or until he
gets bored running his automated scripts, whichever comes first).
The reclaimable flag was there originally, and was one of the flags that
were dropped (unintentionally) by commit 4bdadb9785 ("drm/i915:
Selectively enable self-reclaim") that introduced all these problems,
but I didn't want to just blindly add back all the flags in commit
985b823b91, and it looked like __GFP_RECLAIM wasn't necessary. It
clearly was.
I still suspect that there is some subtle reason we're missing that
causes the problems, but __GFP_RECLAIMABLE is certainly not wrong to use
in this context, and is what the code historically used. And we have no
idea what the causes the corruption without it.
Reported-and-tested-by: M. Vefa Bicakci <bicave@superonline.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* drm-intel-lru:
drm: implement helper functions for scanning lru list
drm_mm: extract check_free_mm_node
drm: sane naming for drm_mm.c
drm: kill dead code in drm_mm.c
drm: kill drm_mm_node->private
drm: use list_for_each_entry in drm_mm.c
* drm-platform:
drm: Make sure the DRM offset matches the CPU
drm: Add __arm defines to DRM
drm: Add support for platform devices to register as DRM devices
drm: Remove drm_resource wrappers
Only ever assigned, never used.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[glisse: I will re-add if needed for range-restricted allocations]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On some machines (currently only the Toshiba Tecra A11 is known), the GPU
locks up when modeset is forced on LID open. This patch adds a new DMI
blacklist and omits modesetting for all matches.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15550
Signed-off-by: Thomas Bächler <thomas@archlinux.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix page flip finish vs. prepare on plane B
drm/i915: change default panel fitting mode to preserve aspect ratio
drm/i915: fix uninitialized variable warning in i915_setup_compression()
drm/i915: take struct_mutex in i915_dma_cleanup()
drm/i915: Fix CRT hotplug regression in 2.6.35-rc1
i915: fix ironlake edp panel setup (v4)
drm/i915: don't access FW_BLC_SELF on 965G
drm/i915: Account for space on the ring buffer consumed whilst wrapping.
drm/i915: gen3 page flipping fixes
drm/i915: don't queue flips during a flip pending event
drm/i915: Fix incorrect intel_ring_begin size in BSD ringbuffer.
drm/i915: Turn on 945 self-refresh only if single CRTC is active
drm/i915/gen4: Fix interrupt setup ordering
drm/i915: Use RSEN instead of HTPLG for tfp410 monitor detection.
drm/i915: Move non-phys cursors into the GTT
Revert "drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on)."
(Included the "fix page flip finish vs. prepare on plane B" patch from
Jesse on top of the pull request from Eric. -- Linus)
Since commit 4bdadb9785 ("drm/i915:
Selectively enable self-reclaim"), we've been passing GFP_MOVABLE to the
i915 page allocator where we weren't before due to some over-eager
removal of the page mapping gfp_flags games the code used to play.
This caused hibernate on Intel hardware to result in a lot of memory
corruptions on resume. See for example
http://bugzilla.kernel.org/show_bug.cgi?id=13811
Reported-by: Evengi Golov (in bugzilla)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tested-by: M. Vefa Bicakci <bicave@superonline.com>
Cc: stable@kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We did this a long time ago in the DDX driver, but now this fix belongs
in the kernel.
Preserving the aspect ratio is a nicer default.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=18033.
Tested-by: Josh Triplett <josh@freedesktop.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes:
drivers/gpu/drm/i915/i915_dma.c: In function ‘i915_setup_compression’:
drivers/gpu/drm/i915/i915_dma.c:1311: error: ‘compressed_llb’ may be used uninitialized in this function
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
intel_cleanup_ring_buffer() calls drm_gem_object_unreference() (as
opposed to drm_gem_object_unreference_unlocked()) so it needs to be
called with "struct_mutex" held. If we don't hold the lock, it triggers
a BUG_ON(!mutex_is_locked(&dev->struct_mutex));
I also audited the other places that call intel_cleanup_ring_buffer()
and they all hold the lock so they're OK.
This was introduced in: 8187a2b70e "drm/i915: introduce
intel_ring_buffer structure (V2)" and it's a regression from v2.6.34.
Addresses: https://bugzilla.kernel.org/show_bug.cgi?id=16247
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reported-by: Benny Halevy <bhalevy@panasas.com>
Tested-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit 7a772c492f has two bugs which
made the hotplug problems on my laptop worse instead of better.
First, it did not, in fact, disable the CRT plug interrupt -- it
disabled all the other hotplug interrupts. It seems rather doubtful
that that bit of the patch fixed anything, so let's just remove it.
(If you want to add it back, you probably meant ~CRT_HOTPLUG_INT_EN.)
Second, on at least my GM45, setting CRT_HOTPLUG_ACTIVATION_PERIOD_64
and CRT_HOTPLUG_VOLTAGE_COMPARE_50 (when they were previously unset)
causes a hotplug interrupt about three seconds later. The old code
never restored PORT_HOTPLUG_EN so this could only happen once, but
they new code restores those registers. So just set those bits when
we set up the interrupt in the first place.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Eric Anholt <eric@anholt.net>
The eDP spec claims a 20% overhead for the 8:10 encoding scheme used
on the wire. Take this into account when picking the lane/clock speed
for the panel.
v3: some panels are out of spec, try our best to deal with them, don't
refuse modes on eDP panels, and try the largest allowed settings if
all else fails on eDP.
v4: fix stupid typo, forgot to git add before amending.
Fixes several reports in bugzilla:
https://bugs.freedesktop.org/show_bug.cgi?id=28070
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The register offset for FW_BLC_SELF is a totally different set of bits
on Broadwater (it's actually MI_RDRET_STATE), so don't treat it like
FW_BLC_SELF on 965G chips.
Fixes bug https://bugs.freedesktop.org/show_bug.cgi?id=26874.
Cc: stable@kernel.org
Tested-by: Norman Yarvin <yarvin@yarchive.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
If we fill the tail of the physical ring buffer with NOOP when wrapping,
we need to account for the reduction in available space.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Gen3 chips have slightly different flip commands, and also contain a bit
that indicates whether a "flip pending" interrupt means the flip has
been queued or has been completed.
So implement support for the gen3 flip command, and make sure we use the
flip pending interrupt correctly depending on the value of ECOSKPD bit
0.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Hardware will set the flip pending ISR bit as soon as it receives the
flip instruction, and (supposedly) clear it once the flip completes
(e.g. at the next vblank). If we try to send down a flip instruction
while the ISR bit is set, the hardware can become very confused, and we
may never receive the corresponding flip pending interrupt, effectively
hanging the chip.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The ring_begin API was taking a number of bytes, while all of our
other begin/end macros take number of dwords. Change the API over to
dwords to prevent future bugs.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Enable self-refresh on 945 when just one CRTC is activated.
Otherwise user would get display flicker with dual display.
This fixes https://bugs.freedesktop.org/show_bug.cgi?id=27667
Signed-off-by: Li Peng <peng.li@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This reverts commit cfecde435d, since it
seems to cause some systems to not come up with any video output at all
(or video that only comes on when X starts up).
Fixes bugzilla:
http://bugzilla.kernel.org/show_bug.cgi?id=16163
Reported-and-tested-by: David John <davidjon@xenontk.org>
Tested-by: Nick Bowler <nbowler@elliptictech.com>
Acked-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous commit fixes the problem, these commits make sure we actually
fail properly if it happens again.
I've squashed the commits from Chris since they are all fixing one issue.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
(regression fix since fbdev/kms rework).
My fb rework didn't remember about the 84/65s.
Reported-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cursors need to be in the GTT domain when being accessed by the GPU.
Previously this was a fortuitous byproduct of userspace using pwrite()
to upload the image data into the cursor. The redundant clflush was
removed in commit 9b8c4a and so the image was no longer being flushed
out of the caches into main memory. One could also devise a scenario
where the cursor was rendered by the GPU, prior to being attached as the
cursor, resulting in similar corruption due to the missing MI_FLUSH.
Fixes:
Bug 28335 - Cursor corruption caused by commit 9b8c4a0b21https://bugs.freedesktop.org/show_bug.cgi?id=28335
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unmask, then enable interrupts, then enable interrupt sources; matches
PCH ordering. The old way (sources, enable, unmask) gives a window
during which interrupt conditions would appear in ISR but would never
reach IIR and thus never raise an IRQ. Since interrupts only trigger
on rising edges in ISR, this would lead to conditions where (for
example) output hotplugging would never fire an interrupt because it
was already stuck on in ISR.
Also, since we know IIR and PIPExSTAT have been cleared during
irq_preinstall, don't clear them again during irq_postinstall, nothing
good can come of that.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (41 commits)
drm/radeon/kms: make sure display hw is disabled when suspending
drm/vmwgfx: Allow userspace to change default layout. Bump minor.
drm/vmwgfx: Fix framebuffer modesetting
drm/vmwgfx: Fix vga save / restore with display topology.
vgaarb: use MIT license
vgaarb: convert pr_devel() to pr_debug()
drm: fix typos in Linux DRM Developer's Guide
drm/radeon/kms/pm: voltage fixes
drm/radeon/kms/pm: radeon_set_power_state fixes
drm/radeon/kms/pm: patch default power state with default clocks/voltages on r6xx+
drm/radeon/kms/pm: enable SetVoltage on r7xx/evergreen
drm/radeon/kms/pm: add support for SetVoltage cmd table (V2)
drm/radeon/kms/evergreen: add initial CS parser
drm/kms: disable/enable poll around switcheroo on/off
drm/nouveau: fixup confusion over which handle the DSM is hanging off.
drm/nouveau: attempt to get bios from ACPI v3
drm/nv50: cast IGP memory location to u64 before shifting
drm/ttm: Fix ttm_page_alloc.c
drm/ttm: Fix cached TTM page allocation.
drm/vmwgfx: Remove some leftover debug messages.
...
Cursors need to be in the GTT domain when being accessed by the GPU.
Previously this was a fortuitous byproduct of userspace using pwrite()
to upload the image data into the cursor. The redundant clflush was
removed in commit 9b8c4a and so the image was no longer being flushed
out of the caches into main memory. One could also devise a scenario
where the cursor was rendered by the GPU, prior to being attached as the
cursor, resulting in similar corruption due to the missing MI_FLUSH.
Fixes:
Bug 28335 - Cursor corruption caused by commit 9b8c4a0b21https://bugs.freedesktop.org/show_bug.cgi?id=28335
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Arkadiusz Miśkiewicz <arekm@maven.pl>
Signed-off-by: Eric Anholt <eric@anholt.net>
This reverts commit cfecde435d.
The commit was first created as an attempt to fix LVDS initialiazation
on Ironlake. Testing revealed that it didn't fix that, but it was
assumed to still be correct anyway.
Subsequent testing has revealed that this commit has caused other
regressions:
* Change in VBlank interrupt frequency causing 60% 3D performance regression
http://bugs.freedesktop.org/show_bug.cgi?id=27698
* Black screen on G45
http://bugs.freedesktop.org/show_bug.cgi?id=27733
So revert this buggy code for now to revisit later when we can fix
actual bugs without causing these regressions.
Signed-off-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This will let userland only try to use the new media decode
functionality when the appropriate kernel is present.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
I'm actually kind of shocked that it works at all otherwise.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Allow platform devices without PCI resources to be DRM devices.
[airlied: fixup warnings with dev pointers]
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Remove the drm_resource wrappers and directly use the
actual PCI and/or platform functions in their place.
[airlied: fixup nouveau properly to build]
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With splitted engines on Sandybridge, each engine has its own
interrupt control as well. This unmasks the interrupt to properly
enable pipe control notify event for render engine.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Sandybridge(Gen6) has new format for PIPE_CONTROL command,
the flush and post-op control are in dword 1 now. This
changes command length field for difference between Ironlake
and Sandybridge.
I tried to test this with noop request and issue PIPE_CONTROL
command for each sequence and track notify interrupts, which
seems work fine. Hopefully we don't need workaround like on
Ironlake for Sandybridge.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Since we now get_user_pages() outside of the mutex prior to performing
the copy, we kmap() the page inside the copy routine and so need to
perform an ordinary memcpy() and not copy_from_user().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
As we do not have a requirement to be atomic and avoid sleeping whilst
performing the slow copy for shmem based pread and pwrite, we can use
kmap instead, thus simplifying the code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
We can avoid an early clflush when pwriting if we use the current CPU
write domain rather than moving the object to the GTT domain for the
purposes of the pwrite. This has the advantage of not flushing the
presumably hot data that we want to upload into the bo, and of ascribing
the clflush to the execution when profiling.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
The callers expect us to cleanup any partially initialised structures
before reporting the error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
If the object is bigger than the entire aperture, reject it early
before evicting everything in a vain attempt to find space.
v2: Use E2BIG as suggested by Owain G. Ainsworth.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
This particular warning is harmless as we emit during the normal
pinning process where the batch buffer requires more fences than is
available without eviction. Only if we fail to evict enough fences does
this become a problem, so include the requested number of fences in the
ultimate *error* message.
v2: Remember to compile test even trial patches to remove warnings.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add the pitch that we about to write into the control register along
with the base, offset and coordinates that go into the other control
registers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
If the FBC is already disabled, then we do not even attempt to disable
FBC and so there is no point emitting a debug statement at that point,
having already emitted one saying why we are disabling FBC.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Nesting domain changes will cause confusion when trying to interpret the
tracepoints describing the sequence of changes for the object, as well
as obscuring the order of operations for the reader of the code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Delay taking the mutex until we need to and ensure that we hold the
spinlock when resetting unpin_work on the error path. Also defer the
debugging print messages until after we have released the spinlock.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Kristian Høgsberg <krh@bitplanet.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Only report an error if the GPU has actually detected one, otherwise we
are just hung.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Pineview with DDR3 memory has different latencies to enable CxSR.
This patch updates CxSR latency table to add Pineview DDR3 latency
configuration. It also adds one flag "is_ddr3" for checking DDR3
setting in MCHBAR.
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Peng <peng.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The "encoder" variable can never be null because it is used as loop
cursor in a list_for_each_entry() loop.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The "connector" variable is used as the cursor in a
list_for_each_entry() and it's always non-null so we don't need to check
it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For real HDMI sink, CPT HDMI port has to set 'HDMI' mode flag
in order to make HDMI audio work correctly.
This is required patch for drm/i915 to enable HDMI audio on CPT PCH,
ALSA patch is at http://mailman.alsa-project.org/pipermail/alsa-devel/2010-May/027601.html
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This saves a whooping 7 dwords. Zero functional changes. Because
some of the refcounts are rather tightly calculated, I've put
BUG_ONs in the code to check for overflows.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
We can, by virtue of a vblank interrupt firing in the middle of setting
up the unpin work (i.e. after we set the unpin_work field and before we
write to the ringbuffer) enter intel_finish_page_flip() prior to
receiving the pending flip notification. Therefore we can expect to hit
intel_finish_page_flip() under normal circumstances without a pending flip
and even without installing the pending_flip_obj. This is exacerbated by
aperture thrashing whilst binding the framebuffer
References:
Bug 28079 - "glresize" causes kernel panic in intel_finish_page_flip.
https://bugs.freedesktop.org/show_bug.cgi?id=28079
Reported-by: Nick Bowler <nbowler@draconx.ca>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add power monitoring support to the i915 driver for use by the IPS
driver. Export the available power info to the IPS driver through a few
new inter-driver hooks. When used together, the IPS driver and this
patch can significantly increase graphics performance on Ironlake class
chips.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Fixed 32-bit compile. stupid obfuscating div_u64()]
Signed-off-by: Eric Anholt <eric@anholt.net>
Disable the CRT plug interrupt while doing the force cycle, explicitly
clear any CRT interrupt we may have generated, and restore when done.
Should mitigate interrupt storms from hotplug detection.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This doesn't change the clock limits (minimums), i.e. it won't make it
output 720x576 PAL nor 720x480 NTSC, but it will work with modes like
1080i etc. (including GLX and textured Xvideo, not sure about the
overlay).
Tested on i915 + analog VGA, it would be worth checking if newer chips
(and which ones) still support interlaced mode.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Eric Anholt <eric@anholt.net>
While investigating Intel i5 Arrandale GPU lockups with -rc4, I
noticed a lock imbalance.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Convert i915_gem_object_clflush to DEFINE_EVENT, and save ~0.5K:
text data bss dec hex filename
13204 2732 12 15948 3e4c i915_trace_points.o.orig
12668 2732 12 15412 3c34 i915_trace_points.o
No change in functionality.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
FBC disable on 965 can take long enough to trigger latency checks in the
kernel so be sure to timeout after a reasonable period.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15015.
Tested-by: James Ettle <theholyettlz@googlemail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The BSD (bit stream decoder) ring is used for accessing the BSD engine
which decodes video bitstream for H.264 and VC1 on G45+. It is
asynchronous with the render ring and has access to separate parts of
the GPU from it, though the render cache is coherent between the two.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Xiang Hai hao <haihao.xiang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The active list and request list move into the ringbuffer structure,
so each can track its active objects in the order they are in that
ring. The flushing list does not, as it doesn't matter which ring
caused data to end up in the render cache. Objects gain a pointer to
the ring they are active on (if any).
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Xiang Hai hao <haihao.xiang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Introduces a more complete intel_ring_buffer structure with callbacks
for setup and management of a particular ringbuffer, and converts the
render ring buffer consumers to use it.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Xiang Hai hao <haihao.xiang@intel.com>
[anholt: Fixed up whitespace fail and rebased against prep patches]
Signed-off-by: Eric Anholt <eric@anholt.net>
This is preparation for supporting multiple ringbuffers on Ironlake.
The non-copy-and-paste changes are:
- de-staticing functions
- I915_GEM_GPU_DOMAINS moving to i915_drv.h to be used by both files.
- i915_gem_add_request had only half its implementation
copy-and-pasted out of the middle of it.
* 'drm-for-2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (207 commits)
drm/radeon/kms/pm/r600: select the mid clock mode for single head low profile
drm/radeon: fix power supply kconfig interaction.
drm/radeon/kms: record object that have been list reserved
drm/radeon: AGP memory is only I/O if the aperture can be mapped by the CPU.
drm/radeon/kms: don't default display priority to high on rs4xx
drm/edid: fix typo in 1600x1200@75 mode
drm/nouveau: fix i2c-related init table handlers
drm/nouveau: support init table i2c device identifier 0x81
drm/nouveau: ensure we've parsed i2c table entry for INIT_*I2C* handlers
drm/nouveau: display error message for any failed init table opcode
drm/nouveau: fix init table handlers to return proper error codes
drm/nv50: support fractional feedback divider on newer chips
drm/nv50: fix monitor detection on certain chipsets
drm/nv50: store full dcb i2c entry from vbios
drm/nv50: fix suspend/resume with DP outputs
drm/nv50: output calculated crtc pll when debugging on
drm/nouveau: dump pll limits entries when debugging is on
drm/nouveau: bios parser fixes for eDP boards
drm/nouveau: fix a nouveau_bo dereference after it's been destroyed
drm/nv40: remove some completed ctxprog TODOs
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
* anholt/drm-intel-next: (515 commits)
drm/i915: Fix out of tree builds
drm/i915: move fence lru to struct drm_i915_fence_reg
drm/i915: don't allow tiling changes on pinned buffers v2
drm/i915: Be extra careful about A/D matching for multifunction SDVO
drm/i915: Fix DDC bus selection for multifunction SDVO
drm/i915: cleanup mode setting before unmapping registers
drm/i915: Make fbc control wrapper functions
drm/i915: Wait for the GPU whilst shrinking, if truly desperate.
drm/i915: Use spatio-temporal dithering on PCH
[MTD] Remove zero-length files mtdbdi.c and internal.ho
pata_pcmcia / ide-cs: Fix bad hashes for Transcend and kingston IDs
libata: Fix several inaccuracies in developer's guide
slub: Fix bad boundary check in init_kmem_cache_nodes()
raid6: fix recovery performance regression
KEYS: call_sbin_request_key() must write lock keyrings before modifying them
KEYS: Use RCU dereference wrappers in keyring key type code
KEYS: find_keyring_by_name() can gain access to a freed keyring
ALSA: hda: Fix 0 dB for Packard Bell models using Conexant CX20549 (Venice)
ALSA: hda - Add quirk for Dell Inspiron 19T using a Conexant CX20582
ALSA: take tu->qlock with irqs disabled
...
After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.
v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.
v3: add config lock take inside polling, add intel/nouveau poll init/fini calls
v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.
glisse: discard drm_helper_hpd_irq_event
v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It removes a hack from nouveau code which had to detect which
region to pass to kick vesafb/efifb.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
i915_error_object_create() is called from the timer interrupt and hence
can corrupt the KM_USER0 slot. Use KM_IRQ0 instead.
Reported-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Tested-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes up include paths for i915_trace.h by setting additional CFLAGS
for i915_trace_points.c to include the $src directory. The required
TRACE_INCLUDE_PATH is then "."
Signed-off-by: Peter Clifton <pcjc2@cam.ac.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
This lru tracks fences, not objects, so move it to where it belongs.
As a side effect, this nicely shrinks drm_i915_gem_object by two
pointers.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Makes no sense and complicates matters for pipelined tiling changes.
So don't allow it and return -EBUSY.
v2: Fix reference leak. Thanks to Owain Ainsworth for spotting this.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
If we're both RGB and TMDS capable, we'll have set up one connector for
each. When determining connectivity, require analog/digital state in
the EDID block to match analog/digital support in the connector.
Otherwise, both DVI and VGA will appear to be connected.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Multifunction SDVO cards stopped working after 14571b4, and would report
something that looked remarkably like an ADD2 SPD ROM instead of EDID.
This appears to be because DDC bus selection was utterly horked by that
commit; controlled_output was no longer always a single bit, so
intel_sdvo_select_ddc_bus would pick bus 0, which is (unsurprisingly)
the SPD ROM bus, not a DDC bus.
So, instead of that, let's just use the DDC bus the child device table
tells us to use. I'm guessing at the bitmask and shifting from VBIOS
dumps, but it can't possibly be worse.
cf. https://bugzilla.redhat.com/584229
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/radeon/r300.c
The BSD ringbuffer support that is landing in this branch
significantly conflicts with the Ironlake PIPE_CONTROL fix on master,
and requires it to be tested successfully anyway.
We'll turn off outputs etc at unload time, so don't unmap the registers
before doing it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
By idling the GPU and discarding everything we can when under extreme
memory pressure, the number of OOM-killer events is dramatically
reduced. For instance, this makes it possible to run
firefox-planet-gnome.trace again on my swapless 512MiB i915.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Spatial dither is better than nothing, but ST is even better.
(from ajax's followup message:)
I noticed this with:
http://ajax.fedorapeople.org/YellowFlower.jpg
set as my desktop background in Gnome on a 1280x800 machine (in
particular, a Sony Vaio VPCB1 with 6-bit panel and a rather bright black
level). Easiest way to test this is by poking at PIPEACONF with
intel_reg_write directly:
% sudo intel_reg_write 0x70008 0xc0000040 # no dither
% sudo intel_reg_write 0x70008 0xc0000050 # spatial
% sudo intel_reg_write 0x70008 0xc0000054 # ST
I notice it especially strongly in the relatively flat dark area in the
top left. Closer than about 18" I can see a noticeable checkerboard
pattern with plain spatial dithering. ST smooths that out; I can still
tell that it's lacking color precision, but it's not offensive.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
My PIPE_CONTROL fix (just sent via Eric's tree) was buggy; I was
testing a whole set of patches together and missed a conversion to the
new HAS_PIPE_CONTROL macro, which will cause breakage on non-Ironlake
965 class chips. Fortunately, the fix is trivial and has been tested.
Be sure to use the HAS_PIPE_CONTROL macro in i915_get_gem_seqno, or
we'll end up reading the wrong graphics memory, likely causing hangs,
crashes, or worse.
Reported-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Tested-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since 965, the hardware has supported the PIPE_CONTROL command, which
provides fine grained GPU cache flushing control. On recent chipsets,
this instruction is required for reliable interrupt and sequence number
reporting in the driver.
So add support for this instruction, including workarounds, on Ironlake
and Sandy Bridge hardware.
https://bugs.freedesktop.org/show_bug.cgi?id=27108
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
This keeps the memory manager from complaining when we take it down.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Eric mentioned on irc this patch was bad, so revert it.
This reverts commit fb8b5a39b6.
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Luckily the change is quite a little bit less invasive than I've
feared.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Thanks to the to_intel_bo helper, this change is rather trivial.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just embed it and adjust the pointers, No other changes (that's
for later patches).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just preparation, no functional change.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When drivers embed the core gem object into their own structures,
they'll have to do this. Temporarily this results in an ugly
kfree(gem_obj);
in every gem driver.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-fbdev-cleanup:
drm/fb: remove drm_fb_helper_setcolreg
drm/kms/fb: use slow work mechanism for normal hotplug also.
drm/kms/fb: add polling support for when nothing is connected.
drm/kms/fb: provide a 1024x768 fbcon if no outputs found.
drm/kms/fb: separate fbdev connector list from core drm connectors
drm/kms/fb: move to using fb helper crtc grouping instead of core crtc list
drm/fb: fix fbdev object model + cleanup properly.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/nouveau/nouveau_drv.h
* 'anholt/drm-intel-next' of /home/airlied/kernel/drm-next: (48 commits)
agp/intel-gtt: kill previous_size assignments
agp/intel-gtt: kill intel_i830_tlbflush
agp/intel: split out gmch/gtt probe, part 1
agp/intel: kill mutli_gmch_chip
agp/intel: uncoditionally reconfigure driver on resume
agp/intel: split out the GTT support
agp/intel: introduce intel-agp.h header file
drm/i915: Don't touch PORT_HOTPLUG_EN in intel_dp_detect()
drm/i915/pch: Use minimal number of FDI lanes (v2)
drm/i915: Add the support of memory self-refresh on Ironlake
drm/i915: Move Pineview CxSR and watermark code into update_wm hook.
drm/i915: Only save/restore FBC on the platform that supports FBC
drm/i915: Fix the incorrect argument for SDVO SET_TV_format command
drm/i915: Add support of SDVO on Ibexpeak PCH
drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on).
drm/i915: do not read uninitialized ->dev_private
Revert "drm/i915: Use a dmi quirk to skip a broken SDVO TV output."
drm/i915: implement multifunction SDVO device support
drm/i915: remove unused intel_pipe_get_connector()
drm/i915: remove connector object in old output structure
...
Current code is definitely crap: Largest pitch allowed spills into
the TILING_Y bit of the fence registers ... :(
I've rewritten the limits check under the assumption that 3rd gen hw
has a 3d pitch limit of 8kb (like 2nd gen). This is supported by an
otherwise totally misleading XXX comment.
This bug mostly resulted in tiling-corrupted pixmaps because the kernel
allowed too wide buffers to be tiled. Bug brought to the light by the
xf86-video-intel 2.11 release because that unconditionally enabled
tiling for pixmaps, relying on the kernel to check things. Tiling for
the framebuffer was not affected because the ddx does some additional
checks there ensure the buffer is within hw-limits.
v2: Instead of computing the value that would be written into the
hw fence registers and then checking the limits simply check whether
the stride is above the 8kb limit. To better document the hw, add
some WARN_ONs in i915_write_fence_reg like I've done for the i830
case (using the right limits).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=27449
Tested-by: Alexander Lam <lambchop468@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
PORT_HOTPLUG_EN has allready been setup in i915_driver_irq_postinstall(),
when intel_dp_detect() runs.
Delete the DP[BCD]_HOTPLUG_INT_EN defines, they are not referenced anymore.
I found this while searching for a fix for
https://bugzilla.redhat.com/show_bug.cgi?id=528312
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
we used to set the DIDL in the output device detected order.
But some BIOSes requires it to be initialized in the ACPI device order.
e.g. the value of the first field in DIDL stands for the first
ACPI video output device in ACPI namespace.
Now we initialize the DIDL using the device id, i.e. _ADR return value,
of each ACPI video device, if it is not 0.
https://bugzilla.kernel.org/show_bug.cgi?id=15054
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This should be a small power savings. Tested on Lenovo T410 (Ironlake), LVDS
VGA and DisplayPort, up to 1920x1200R.
v2: Add Sandybridge support, fix obvious math error.
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
IS_MOBILE() catches 85x, so we'd always try to use the 9xx FIFO sizing;
since there's an explicit 85x version, this seems wrong.
v2: Handle 830m correctly too.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Ignore LVDS EDID when it is unavailabe or invalid
drm/i915: Add no_lvds entry for the Clientron U800
drm/i915: Rename many remaining uses of "output" to encoder or connector.
drm/i915: Rename intel_output to intel_encoder.
agp/intel: intel_845_driver is an agp driver!
drm/i915: introduce to_intel_bo helper
drm/i915: Disable FBC on 915GM and 945GM.
Update the self-refresh watermark for display plane/cursor and enable
the memory self-refresh on Ironlake. The watermark is also updated for
the active display plane.
More than 1W idle power is saved on one Ironlake laptop after enabling
memory self-refresh.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Previously, after setting up the Pineview CxSR state, i9xx_update_wm would
get called and overwrite our state.
BTW: We will disable the self-refresh and never enable it any more if we
can't find the appropriate the latency on pineview plaftorm. In such case
the update_wm callback will be NULL.
The bitmask macro is also defined to access the corresponding fifo
watermark register.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Otherwise it will cause that S-video output becomes black/white when
switching to other TV format.
http://bugs.freedesktop.org/show_bug.cgi?id=23916
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Arnold <arnold.erbsloeh@web.de>
Tested-by: Bazin <bazin.cz@gmail.com>
Tested-by: Nigel <nigel_tuck@eircom.net>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
SDVO on Ibexpeak PCH with Ironlake is multiplexed with
HDMIB port, and only has SDVOB port.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
The existing code handling the DPMS ON event is much more careful to
ensure that these registers are enabled according to strict sequencing
requirements. Enabling these early in mode_set simply defeats that.
Signed-off-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
->dev_private at that point is NULL and is initialied only a few lines
later.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This reverts commit 6070a4a928.
The quirk for this SDVO device on IBM specific board is just a hack
in old code which showed the broken multifunction SDVO support in
the driver. Multifunction SDVO patch provided the right fix for it.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
With new intel_encoder/intel_connector structure change, each supported
connector type on SDVO device will be created as a new 'intel_connector',
and all attached to one 'intel_encoder' for its SDVO port.
The SDVO encoder will handle SDVO protocol stuff, and each connector does
its own part of work now, like detection is only to check if current active
output is itself, etc.
Update since last submit:
- Fixed SDVO TV property creation failure by incorrect set target output call
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
As all display drivers have been converted, remove the left reference
for connector object in old structure.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Probably only matters for format-converting dongles, but might as well
get it right all the time.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
DP on Cougarpoint has new training pattern definitions, and
new transcoder DP control register is used to determine the mapping
for transcoder and DP digital output. And eDP for Sandybridge has
new voltage and pre-emphasis level definitions.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
To make CRT force detect reliable on Cougarpoint, we need to
disable DAC before force detect, and restore back when trigger
is completed.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Cougarpoint is the new PCH for Sandybridge CPU. This one resolves the
chipset change for display pipeline compared to previous Ibexpeak PCH.
Sandybridge/Cougarpoint has different FDI training parameters, so this also
makes seperate FDI training functions for IBX and CPT. Other change includes
new transcoder DPLL select function to set which DPLL for transcoder to pick
up.
And with another new transcoder C introduced in Cougarpoint, each connector
has new transcoder select bits. This one adds that change to light up VGA.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
PCH is the new name for south bridge from Ironlake/Sandybridge,
which contains most of the display outputs except eDP. This one
adds a probe function to detect current PCH type, and method to
detect Cougarpoint PCH.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Integrated TV is deprecated in new chips from Ironlake.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
OpRegion event on 965G requires legacy BLC event enabled in pipe stat. As LVDS
could be on either pipe now, we should enable BLC event on both pipe. If fail to
do so, we couldn't handle the brightness request triggered from graphics
opregion.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This was brought over from UMS, and used for a while until we decided
that drm_helper_resume_force_mode was easier and more reliable, since
it didn't require duplicating all the code deleted here. We just
forgot to delete all that junk for a while.
This trys to shut up complains about invalid LVDS EDID during
mode probe, but uses fixed panel mode directly for panels with
broken EDID.
https://bugs.freedesktop.org/show_bug.cgi?id=23099https://bugs.freedesktop.org/show_bug.cgi?id=26395
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This one replaces original param for intel_ddc_get_modes() with
DRM connector and i2c bus adapter instead. With explicit params,
we won't require that a single driver structure must hold connector
and DDC bus reference, which ease the conversion to splitted encoder/
connector model.
It also clears up for some cases that we would steal other DDC bus
for mode probe, like VGA analog DDC probe for DVI-I. Also it fixed
a bug in old DVI-I probe handling, that failed to restore origin
analog GPIO port.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In load detection, connector's encoder assignment must be kept
consistent for proper mode setting, and this makes connector as
explicit parameter for load detect function to not require single
data structure to hold both encoder and connector reference, ease
the transition for splitted encoder/connector model.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For introducing splitted encoder/connector structure, this helper will return
connector's attached encoder when needed.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds new structure of intel_connector to present drm's
connector object, which is used to convert from origin single
output into encoder/connector model.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
What we really want is encoder info instead of connector, so change
some more list walk in pipeline setup functions from connector_list
to encoder_list.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Instead of walking through drm connector_list uses encoder_list
for calling hotplug functions which is consistent with intel display
hotplug reporting.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The TV detection logic is not reliable on the Cantiga platform.
Sometimes the TV will be misdetected as the following two cases:
- TV is misdetected on some laptops. e.g. There is no TV connector
port or no TV is attached. But the TV is shown as connected.
- TV connector type is misdetected. e.g. the component TV is
attached, but the TV is shown as S-video type.
According to the hardware requirement, the TV sense state bits of TV DAC
register should be cleared to zero on Cantiga platfrom.
https://bugzilla.kernel.org/show_bug.cgi?id=14792
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Santi <santi@agolina.net>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch is against the drm-fbdevfix1 branch. It removes the
drm_fb_helper_setcolreg function. The reason is that fb_setcolreg is only
used in the case where fb_setcmap is called and no fb_ops->fb_setcmap is
used. In the drm case we always need a fb_setcmap hook to handle multiple
crtcs so we don't need a fb_setcolreg hook. Please apply.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
a) slow work is always used now for any fbcon hotplug, as its not
a fast task and is more suited to being ran under slow work.
b) attempt to not do any fbdev changes when X is running as we'll
just mess it up. This hooks set_par to hopefully do the changes
once X hands control to fbdev.
This also adds the nouveau/intel hotplug support.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This breaks the connection between the core drm connector list
and the fbdev connector usage, and allows them to become disjoint
in the future. It also removes the untype void* that was in the
connector struct to support this.
All connectors are added to the fbdev now but this could be
changed in the future.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This move to using the list of crtcs in the fb helper and cleans up the
whole picking code, now we store the crtc/connectors we want directly
into the modeset and we use the modeset directly to set the mode.
Fixes from James Simmons and Ben Skeggs.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The fbdev layer in the kms code should act like a consumer of the kms services and avoid having relying on information being store in the kms core structures in order for it to work.
This patch
a) removes the info pointer/psuedo palette from the core drm_framebuffer structure and moves it to the fbdev helper layer, it also removes the core drm keeping a list of kernel kms fbdevs.
b) migrated all the fb helper functions out of the crtc helper file into the fb helper file.
c) pushed the fb probing/hotplug control into the driver
d) makes the surface sizes into a structure for ease of passing
This changes the intel/radeon/nouveau drivers to use the new helper.
Signed-off-by: Dave Airlie <airlied@redhat.com>
BugLink: http://bugs.launchpad.net/ubuntu/bugs/544671
This system claims to have a LVDS but has not.
Signed-off-by: Stephane Graber <stgraber@ubuntu.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
CC: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The intel_output naming is inherited from the UMS code, which had a
structure of screen -> CRTC -> output. The DRM code has an additional
notion of encoder/connector, so the structure is screen -> CRTC ->
encoder -> connector. This is a useful structure for SDVO encoders
which can support multiple connectors (each of which requires
different programming in the one encoder and could be connected to
different CRTCs), or for DVI-I, where multiple encoders feed into the
connector for whether it's used for digital or analog. Most of our
code is encoder-related, so transition it to talking about encoders
before we start trying to distinguish connectors.
This patch is produced by sed s/intel_output/intel_encoder/ over the
driver.
Signed-off-by: Eric Anholt <eric@anholt.net>
This is a purely cosmetic change to make changes in this area easier.
And hey, it's not only clearer and typechecked, but actually shorter,
too!
[anholt: To clarify, this is a change to let us later make
drm_i915_gem_object subclass drm_gem_object, instead of having
drm_gem_object have a pointer to i915's private data]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
It is causing hangs after a suspend/resume cycle with the default
powersave=1 module option on these chipsets since 2.6.32-rc.
BugLink: http://bugs.launchpad.net/bugs/492392
Signed-off-by: Robert Hooker <sarvatt@ubuntu.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
I've been getting more and more quirk reports about this. It seems
clear at this point that other OSes are not using this for determining
whether the integrated panel should be turned on, and it is not
reliable for doing so. Better to light up an unintended panel than to
not light up the only usable output on the system.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bug introduced in
commit 10ae9bd25a
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Feb 1 13:59:17 2010 +0100
drm/i915: blow away userspace mappings before fence change
The problem is that when there's no fence reg assigned and the object
is mapped at a fenceable offset in the gtt, the userspace mappings won't
be torn down. Which happens on untiled->tiled transition quite often
on 4th gen and later because there fencing does not have any special
alignment constraints (as opposed to 2nd and 3rd gen on which I've tested
the original commit).
Bugzilla: http://bugs.freedesktop.org/show_bug.cgi?id=26993
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Eric Anholt <eric@anholt.net> (fixes OpenArena)
Signed-off-by: Eric Anholt <eric@anholt.net>
We should free "params" before returning.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Cc: stable@kernel.org (for .33)
Signed-off-by: Eric Anholt <eric@anholt.net>
IS_GEN6 missed to include SandyBridge mobile chip, which failed in
i915_probe_agp() for memory config detection. Fix it with a device
info flag.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
String constants that are continued on subsequent lines with \ will cause
spurious whitespace in the resulting output.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Eric Anholt <eric@anholt.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[anholt: whacked it to wrap to 80 columns instead]
Signed-off-by: Eric Anholt <eric@anholt.net>
This could resolve HW deadlocks where a unit downstream of the VS is
waiting for more input, the VS has one vertex queued up but not
dispatched because it hopes to get one more vertex for 2x4 dispatch,
and software isn't handing more vertices down because it's waiting for
rendering to complete. The B-Spec says you should always have this
bit set.
Signed-off-by: Eric Anholt <eric@anholt.net>
The continue just after this call with loop around and wait for the
request just added just fine. This leads to slightly more compact code.
Signed-Off-by: Owain G. Ainsworth <oga@openbsd.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We probably don't need it for most of the other driver ioctls as well,
but we explicitly did locking when doing the GEM pieces. On CPU-bound
graphics tasks, the BKL was showing up as 1-2% of CPU time.
Signed-off-by: Eric Anholt <eric@anholt.net>
Many new laptops now come with 2 gpus, one to be used for low power
modes and one for gaming/on-ac applications. These GPUs are typically
wired to the laptop panel and VGA ports via a multiplexer unit which
is controlled via ACPI methods.
4 combinations of systems typically exist - with 2 ACPI methods.
Intel/ATI - Lenovo W500/T500 - use ATPX ACPI method
ATI/ATI - some ASUS - use ATPX ACPI Method
Intel/Nvidia - - use _DSM ACPI method
Nvidia/Nvidia - - use _DSM ACPI method.
TODO:
This patch adds support for the ATPX method and initial bits
for the _DSM methods that need to written by someone with
access to the hardware.
Add a proper non-debugfs interface - need to get some proper
testing first.
v2: add power up/down support for both devices
on W500 puts i915/radeon into D3 and cuts power to radeon.
v3: redo probing methods, no DMI list, drm devices call to
register with switcheroo, it tries to find an ATPX method on
any device and once there is two devices + ATPX it inits the
switcher.
v4: ATPX msg handling using buffers - should work on more machines
v5: rearchitect after more mjg59 discussion - move ATPX handling to
radeon driver.
v6: add file headers + initial nouveau bits (to be filled out).
v7: merge delayed switcher code.
v8: avoid suspend/resume of gpu that is off
v9: rearchitect - mjg59 is always right. - move all ATPX code to
radeon, should allow simpler DSM also proper ATRM handling
v10: add ATRM support for radeon BIOS, add mutex to lock vgasr_priv
v11: fix bug in resuming Intel for 2nd time.
v12: start fixing up nvidia code blindly.
v13: blindly guess at finishing nvidia code
v14: remove radeon audio hacks - fix up intel resume more like upstream
v15: clean up printks + remove unnecessary igd/dis pointers
mount debugfs
/sys/kernel/debug/vgaswitcheroo/switch - should exist if ATPX detected
+ 2 cards.
DIS - immediate change to discrete
IGD - immediate change to IGD
DDIS - delayed change to discrete
DIGD - delayed change to IGD
ON - turn on not in use
OFF - turn off not in use
Tested on W500 (Intel/ATI) and T500 (Intel/ATI)
Signed-off-by: Dave Airlie <airlied@redhat.com>
This IBM system has a multi-function SDVO card that reports both VGA
and TV, but the system has no TV connector. The TV connector always
reported as connected, which would lead to poor modesetting choices.
https://bugs.freedesktop.org/show_bug.cgi?id=25787
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Vance <liangghv@sg.ibm.com>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
It would be good to disable the LVDS port when we shut down the panel
to save power. We haven't done so until now because we had trouble
getting the right LVDS parameters from the BIOS. I think we're past
that now, so enabling and disabling the port should be safe, though it
would probably be made cleaner with some additional changes to the
display code, where we also bang on the LVDS reg to set the pairing
correctly etc.
Seems to save a bit of power (up to 300mW in my basic wattsup
meter testing).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The assumption that an object has only ever one write domain is deeply
threaded into gem (it's even encoded the the singular of the variable
name). Don't let userspace screw us over.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Now that we have an exact gpu write domain tracking, we don't need
to move objects to the active list ourself. i915_add_request will
take care of that under all circumstances.
Idea stolen from a patch by Chris Wilson <chris@chris-wilson.co.uk>.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
We have it, so use it. This required moving the function to avoid
a forward declaration.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Chris Wilson
