The L3 throughput can be higher than expected when packed access
is not enabled. The ratio depends on the number of bytes in a
transaction and the EMIF interface width.
The throughput was measured for the following settings/cases:
* Case 1: Burst size of 64 bytes, packed access disabled
* Case 2: Burst size of 64 bytes, packed access enabled
* Case 3: Burst disabled, packed access disabled
Throughput measurements were done during McASP-based audio
playback on the Jacinto6 EVM using the omapconf tool [1]:
$ omapconf trace bw -m sdma_rd
---------------------------------------------------------
Throughput (MB/s)
Audio parameters Case 1 Case 2 Case 3
---------------------------------------------------------
44.1kHz, 16-bits, stereo 1.41 0.18 1.41
44.1kHz, 32-bits, stereo 1.41 0.35 1.41
44.1kHz, 16-bits, 4-chan 2.82 0.35 2.82
44.1kHz, 16-bits, 6-chan 4.23 0.53 4.23
44.1kHz, 16-bits, 8-chan 5.64 0.71 5.64
---------------------------------------------------------
From above measurements, case 2 is the only one that delivers
the expected throughput for the given audio parameters. For
that reason, the packed accesses are now enabled.
It's worth to mention that packed accesses cannot be enabled
for all addressing modes. In cyclic transfers, it can be
enabled in the source for MEM_TO_DEV and in dest for DEV_TO_MEM,
as they use post-increment mode which supports packed accesses.
Peter Ujfalusi:
From the TRM regarding to this:
"NOTE: Except in the constant addressing mode, the source or
destination must be specified as packed for burst transactions
to occur."
So w/o the packed setting the burst on the MEM side was not
enabled, this explains the numbers.
[1] https://github.com/omapconf/omapconf
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the mapping between the hardware request lines and channels has been
removed it no longer make sense to have too many channels.
Set the number of channels to match with the number of logical channels
supported by sDMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Do not direct map the virtual channels to sDMA request number. When the
sDMA is behind of a crossbar this direct mapping can cause situations when
certain channel can not be requested since the crossbar request number
will no longer match with the sDMA request line.
The direct mapping for virtual channels with HW request lines will make it
harder to implement MEM_TO_MEM mode for the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use the dma-requests property from DT to get the number of DMA requests.
In case of legacy boot or failure to find the property, use the default
127 as number of requests.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of magic numbers in the code, use define for number of logical DMA
channels and DMA requests.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The sDMA controller is capable of performing memory copy operation. It need
to be configured to software triggered mode and without HW synchronization.
The sDMA can copy data which is aligned to 8, 16 or 32 bits.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In omap_dma_start_desc the vdesc->node is removed from the virt-dma
framework managed lists (to be precise from the desc_issued list).
If a terminate_all comes before the transfer finishes the omap_desc will
not be freed up because it is not in any of the lists and we stopped the
DMA channel so the transfer will not going to complete.
There is no special sequence for leaking memory when using cyclic (audio)
transfer: with every start and stop of a cyclic transfer the driver leaks
struct omap_desc worth of memory.
Free up the allocated memory directly in omap_dma_terminate_all() since the
framework will not going to do that for us.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: <stable@vger.kernel.org>
CC: <linux-omap@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the TI OMAP DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The dmaengine header abbreviates destination as at least two different strings.
Make a coherent use of a single one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When the audio stream is paused or suspended we stop the sDMA and when it
is unpaused/resumed we start the channel without reconfiguring it.
The omap_dma_stop() clears the link configuration when we pause the dma, but
it is not setting it back on start. This will result only one audio buffer
to be played back and the DMA will stop, since the linking is disabled.
We need to restore the CLINK_CTRL register in case of resume.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add mb() call to resume path to ensure the necessary barrier.
Resume can happen after waking up from suspend for example.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The argument is always set to NULL and never used. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull slave-dmaengine updates from Vinod Koul:
- New driver for Qcom bam dma
- New driver for RCAR peri-peri
- New driver for FSL eDMA
- Various odd fixes and updates thru the subsystem
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (29 commits)
dmaengine: add Qualcomm BAM dma driver
shdma: add R-Car Audio DMAC peri peri driver
dmaengine: sirf: enable generic dt binding for dma channels
dma: omap-dma: Implement device_slave_caps callback
dmaengine: qcom_bam_dma: Add device tree binding
dma: dw: Add suspend and resume handling for PCI mode DW_DMAC.
dma: dw: allocate memory in two stages in probe
Add new line to test result strings produced in verbose mode
dmaengine: pch_dma: use tasklet_kill in teardown
dmaengine: at_hdmac: use tasklet_kill in teardown
dma: cppi41: start tear down only if channel is busy
usb: musb: musb_cppi41: Dont reprogram DMA if tear down is initiated
dmaengine: s3c24xx-dma: make phy->irq signed for error handling
dma: imx-dma: Add missing module owner field
dma: imx-dma: Replace printk with dev_*
dma: fsl-edma: fix static checker warning of NULL dereference
dma: Remove comment about embedding dma_slave_config into custom structs
dma: mmp_tdma: move to generic device tree binding
dma: mmp_pdma: add IRQF_SHARED when request irq
dma: edma: Fix memory leak in edma_prep_dma_cyclic()
...
We can move the handling of the DMA synchronisation control out of the
prepare functions; this can be pre-calculated when the DMA channel has
been allocated, so we don't need to duplicate this in both prepare
functions.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the interrupt handling for OMAP2+ into omap-dma, rather than using
the legacy support in the platform code.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Export the DMA register information from the SoC specific data, such
that we can access the registers directly in omap-dma.c, mapping the
register region ourselves as well.
Rather than calculating the DMA channel register in its entirety for
each access, we pre-calculate an offset base address for the allocated
DMA channel and then just use the appropriate register offset.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide a function to read the CSAC/CDAC register, working around the
OMAP 3.2/3.3 erratum (which requires two reads of the register if the
first returned zero.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide a pair of channel register accessors, and a pair of global
accessors for non-channel specific registers.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to read-modify-write the CCR register; we already know
what value it should contain at this point. Use the cached CCR value
when setting the enable bit.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to issue a barrier for every segment of a DMA transfer;
doing this just once per descriptor will do.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the clnk_ctrl setup to the preparation functions, saving its
value in the omap_desc. This only needs to be set once per descriptor,
not for each segment, so set it in omap_dma_start_desc() rather than
omap_dma_start().
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The only thing which changes is which registers are written, so put this
in local variables instead. This results in smaller code.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate clearing of the channel status register, rather than open
coding the same functionality in two places.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since we record the CCR register in the dma transaction, we can move the
processing of the iframe buffering errata out of the omap_dma_start().
Move it to the preparation functions.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide our own set of more complete register definitions; this allows
us to get rid of the meaningless 1 << n constants scattered throughout
this code.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate the setup of the channel control register. Prepare the
basic value in the preparation of the DMA descriptor, and write it into
the register upon descriptor execution.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate the setup of the channel source destination parameters
register. This way, we calculate the required CSDP value when we setup
a transfer descriptor, and only write it to the device registers once
when we start the descriptor.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Read the current DMA position from the hardware directly rather than via
arch/arm/plat-omap/dma.c.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Program the non-cyclic mode DMA start/stop directly, rather than via
arch/arm/plat-omap/dma.c.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need to keep writing registers which don't change value in
omap_dma_start_sg(). Move this into omap_dma_start_desc() and merge
the register updates together.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Program the transfer parameters directly into the hardware, rather
than using the functions in arch/arm/plat-omap/dma.c.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide and use a hook to obtain the underlying DMA platform operations
so that omap-dma.c can access the hardware more directly without
involving the legacy DMA driver.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use devm_kzalloc() to allocate omap_dmadev() so that we don't need
complex error cleanup paths.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With the callback implemented omap-dma can provide information to client
drivers regarding to supported address widths, directions, residue
granularity, etc.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The channel allocated/released messages are just informative and
not really interesting to users. Change them to "debug" level.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the device-tree blob is present during boot, then register the SDMA
controller with the device-tree DMA driver so that we can use device-tree
to look-up DMA client information.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
cyclic DMA is only used by audio which needs DMA to be started without a
delay.
If the DMA for audio is started using the tasklet we experience random
channel switch (to be more precise: channel shift).
Reported-by: Peter Meerwald <pmeerw@pmeerw.net>
CC: stable@vger.kernel.org # v3.7+
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Otherwise omap dmaengine will initialized when booted
on other SoCs. Fix this by initializing the platform
device in arch/arm/*omap*/dma.c instead.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on earlier discussions[1] we attempted to find a suitable
location for the omap DMA header in commit 2b6c4e73 (ARM: OMAP:
DMA: Move plat/dma.h to plat-omap/dma-omap.h) until the conversion
to dmaengine is complete.
Unfortunately that was before I was able to try to test compile
of the ARM multiplatform builds for omap2+, and the end result
was not very good.
So I'm creating yet another all over the place patch to cut the
last dependency for building omap2+ for ARM multiplatform. After
this, we have finally removed the driver dependencies to the
arch/arm code, except for few drivers that are being worked on.
The other option was to make the <plat-omap/dma-omap.h> path
to work, but we'd have to add some new header directory to for
multiplatform builds.
Or we would have to manually include arch/arm/plat-omap/include
again from arch/arm/Makefile for omap2+.
Neither of these alternatives sound appealing as they will
likely lead addition of various other headers exposed to the
drivers, which we want to avoid for the multiplatform kernels.
Since we already have a minimal include/linux/omap-dma.h,
let's just use that instead and add a note to it to not
use the custom omap DMA functions any longer where possible.
Note that converting omap DMA to dmaengine depends on
dmaengine supporting automatically incrementing the FIFO
address at the device end, and converting all the remaining
legacy drivers. So it's going to be few more merge windows.
[1] https://patchwork.kernel.org/patch/1519591/#
cc: Russell King <linux@arm.linux.org.uk>
cc: Kevin Hilman <khilman@ti.com>
cc: "Benoît Cousson" <b-cousson@ti.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Vinod Koul <vinod.koul@intel.com>
cc: Dan Williams <djbw@fb.com>
cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
cc: David Woodhouse <dwmw2@infradead.org>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
cc: Hans Verkuil <hans.verkuil@cisco.com>
cc: Vaibhav Hiremath <hvaibhav@ti.com>
cc: Lokesh Vutla <lokeshvutla@ti.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
cc: Afzal Mohammed <afzal@ti.com>
cc: linux-crypto@vger.kernel.org
cc: linux-media@vger.kernel.org
cc: linux-mtd@lists.infradead.org
cc: linux-usb@vger.kernel.org
cc: linux-fbdev@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This code will be eventually in drivers, and for the
code in the drivers we don't want to have any cpu_is_omap
usage. Those macros should be private to arch/arm/mach-omap1
and arch/arm/mach-omap2.
To fix this, let's move the define for dma_omap2plus()
to dma-omap.h, and use the existing dma_attr passed in
the platform_data as the revision registers are what they
are.
Note that we can now also remove the relative includes
introduced by the recent clean-up patches.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Drivers should not use cpu_is_omap or cpu_class_is_omap macros,
they should be private to the platform init code. And we'll be
removing plat/cpu.h and only have a private soc.h for the
arch/arm/*omap* code.
This patch is intended as preparation for the core omap changes
and removes the need to include plat/cpu.h from several drivers.
This is needed for the ARM common zImage support.
These changes are OK to do because:
- omap-rng.c does not need plat/cpu.h
- omap-aes.c and omap-sham.c get the proper platform_data
passed to them so they don't need extra checks in the driver
- omap-dma.c and omap-pcm.c can test the arch locally as
omap1 and omap2 cannot be compiled together because of
conflicting compiler flags
Cc: Deepak Saxena <dsaxena@plexity.net>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: linux-kernel@vger.kernel.org
[tony@atomide.com: mmc changes folded in to an earlier patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move plat/dma.h to plat-omap/dma-omap.h as part of single
zImage work
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Misael Lopez Cruz