The generic driver kept a global struct pci_ops ("gen_pci_ops") which it
patched with the .map_bus() method appropriate for the bus device. This is
a problem when we have two different types of bus devices: the .map_bus()
method for the last device probed clobbers the method for previous devices.
The result is that only the last bus device probed has the correct
.map_bus(), and the others fail.
Move the struct pci_ops into the bus-specific structure and initialize a
pointer to it when the bus device is probed.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Will Deacon <will.deacon@arm.com>
After 8d63bc7bea ("PCI/MSI: pci-xgene-msi: Get rid of struct
msi_controller"), it is no longer required to assign msi_controller for
X-Gene PCIe host bridge to support MSI.
Remove this unnecessary code. This also avoids a warning message ("failed
to enable MSI") during boot.
[bhelgaas: changelog]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Tanmay Inamdar <tinamdar@apm.com>
Improve the link detection logic by explicitly querying the link status
register to ensure link is active.
Also force class to PCI_CLASS_BRIDGE_PCI (0x0604) through the host
configuration space register.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
The current reset logic does not always properly reset the device. For
example, in the case when the perst_b signal is already de-asserted in the
bootloader, the current reset logic fails to trigger a proper assert ->
de-assert reset sequence.
Fix the issue by always triggering the proper reset sequence.
Also explicitly select the desired reset source, i.e., perst_b, and reduce
the wait time after the device comes out of reset from 250 ms to 100 ms,
based on recommendation from the ASIC team.
Tested-by: Vladimir Dreizin <vdreizin@broadcom.com>
Tested-by: Darren Edamura <dedamura@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vladimir Dreizin <vdreizin@broadcom.com>
Reviewed-by: Trac Hoang <trhoang@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
After 459a07721c ("PCI: Build setup-irq.o for arm64"), we build
setup-irq.o for arm64, so we can use pci_fixup_irqs() on both arm and
arm64.
Remove the "#ifdef CONFIG_ARM" around the call to pci_fixup_irqs().
[bhelgaas: changelog]
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Resource management
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn Helgaas)
MSI
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=f4c3
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for things we merged for v4.3 (VPD, MSI, and bridge
window management), and a new Renesas R8A7794 SoC device ID.
Details:
Resource management:
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn
Helgaas)
MSI:
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver:
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous:
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)"
* tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: rcar: Add R8A7794 support
PCI: Use function 0 VPD for identical functions, regular VPD for others
PCI: Fix devfn for VPD access through function 0
PCI/MSI: Fix MSI IRQ domains for VFs on virtual buses
PCI: Clear IORESOURCE_UNSET when clipping a bridge window
PCI: Revert "PCI: Call pci_read_bridge_bases() from core instead of arch code"
Add a #define for PCIE_PHY_RX_ASIC_OUT_VALID and use it instead of a
hardcoded value.
[bhelgaas: drop PCIE_PHY_DEBUG_R0_LTSSM_MASK; updated in future patch]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
When devm_request_irq() fails, imx6_add_pcie_port() should return the real
error code instead of always returning -ENODEV.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Add Renesas R8A7794 SoC support to the Renesas R-Car gen2 PCI driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Make get_msi_addr() return phys_addr_t, not u32. This allows the MSI
target address to be above 4GB for 64bit or PAE systems.
No functional change for the current 32bit platform users as phys_addr_t
maps to u32 for them.
[bhelgaas: changelog]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Implement multivector MSI IRQ setup. This allows to set up and use multiple
MSI IRQs per device.
[bhelgaas: changelog, use -EINVAL instead of -ENOSYS]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Factor out the PCI MSI message setup from the single MSI setup function.
This will be reused by the multivector MSI setup.
No functional change yet.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
The value under PORT_LOGIC_LINK_WIDTH_MASK is 0x1, 0x2, 0x4, 0x8. In IP
v4.2, bits [16:8] are defined for NUM_OF_LANES. But in IP v4.4, bits[12:8]
are defined for NUM_OF_LANES, bits [16:13] are for other usages (bit 16 is
AUTO_LANE_FLIP_CTRL_EN, bits [15:13] are PRE_DET_LANE).
As there is no conflict about NUM_OF_LANES between v4.2 and v4.4, change
the mask value to avoid future problems.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
When pci-host-generic looks for the probe-only property, it seems to trust
the DT to be correctly written, and assumes that there is a parameter to
the property.
Unfortunately, this is not always the case, and some firmware expose this
property naked. The driver ends up making a decision based on whatever the
property pointer points to, which is likely to be junk.
Switch to the common of_pci.c implementation that doesn't suffer from this
problem.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
Here's our branch of ARM64 contents for this merge window.
Most of this is DT contents for new SoCs (or those who have seen new
device support added). Maybe we should stop separating out the arm64
contents here to avoid the kind of internal conflicts as we got this
time around, where 32- and 64-bit contents conflicted.
Anyhow, on the actual contents:
New SoCs:
- Broadcom North Star 2 (ns2)
- Marvell Berlin4CT
- Mediatek MT6795
- Rockchip RK3368
In addition, there are enhancements for the following platforms:
- Mediatek MT8173: cpuidle-dt updates, misc other additions
- ZyncMP: A bunch of devices added to the existing DTSI
- Qualcomm MSM8916 and APQ8016 updates for USB, etc.
+ A handful of other updates for various platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SZR9
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit changes from Olof Johansson:
"Here's our branch of ARM64 contents for this merge window.
Most of this is DT contents for new SoCs (or those who have seen new
device support added). Maybe we should stop separating out the arm64
contents here to avoid the kind of internal conflicts as we got this
time around, where 32- and 64-bit contents conflicted.
Anyhow, on the actual contents:
New SoCs:
- Broadcom North Star 2 (ns2)
- Marvell Berlin4CT
- Mediatek MT6795
- Rockchip RK3368
In addition, there are enhancements for the following platforms:
- Mediatek MT8173: cpuidle-dt updates, misc other additions
- ZyncMP: A bunch of devices added to the existing DTSI
- Qualcomm MSM8916 and APQ8016 updates for USB, etc.
+ a handful of other updates for various platforms"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (47 commits)
ARM64: dts: vexpress: Use assigned-clock-parents for sp810
ARM64: dts: mt6795: enable basic SMP bringup for MT6795
arm64: Enable Marvell Berlin SoC family in defconfig
arm64: Enable Marvell Berlin SoC family in Kconfig
arm64: dts: Add dts files for Marvell Berlin4CT SoC
ARM64: zynqmp: Move SPI nodes to the right location
ARM64: zynqmp: Move uart and ttcs to the right location
ARM64: zynqmp: Enable spi flashes on ep108
ARM64: zynqmp: Add eeprom memories on i2c bus
ARM64: zynqmp: Enable sdhci on ep108
ARM64: zynqmp: Enable watchdog on ep108
ARM64: zynqmp: Add DWC3 usb support
ARM64: zynqmp: Add SMMU support
ARM64: zynqmp: Add CANs node for platform
ARM64: zynqmp: Use zynqmp specific compatible string for gpio
devicetree: xilinx: zynqmp: add sata node
PCI: iproc: Fix BCMA dependency in Kconfig
arm64: dts: Add Broadcom North Star 2 support
arm64: Add Broadcom iProc family support
PCI: iproc: Fix ARM64 dependency in Kconfig
...
* pci/host-dra7xx:
PCI: dra7xx: Remove unneeded use of IS_ERR_VALUE()
* pci/host-imx6:
PCI: imx6: Simplify a trivial if-return sequence
* pci/host-spear:
PCI: spear: Use BUG_ON() instead of condition followed by BUG()
of_parse_phandle() returns a device_node pointer with the refcount
incremented. We should dispose of this reference when we're finished.
Drop the reference acquired by of_parse_phandle().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
ARM previously stored the msi_controller pointer in its sysdata, struct
pci_sys_data, and implemented pcibios_msi_controller() to retrieve it.
That made PCI host controller drivers specific to ARM because they had to
put the msi_controller pointer in the ARM-specific pci_sys_data.
There is now a generic mechanism, pci_scan_root_bus_msi(), for giving the
msi_controller pointer to the PCI core. Use this for all ARM systems and
for the DesignWare and Xilinx PCI host controller drivers.
This removes an ARM dependency from the DesignWare, DRA7xx, EXYNOS, i.MX6,
Keystone, Layerscape, SPEAr13xx, and Xilinx drivers.
[bhelgaas: changelog, split into separate patch]
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Simon Horman <horms@verge.net.au>
CC: Russell King <linux@arm.linux.org.uk>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: Marc Zyngier <marc.zyngier@arm.com>
Make pci-host-generic driver (kernel option PCI_HOST_GENERIC) available on
arm64.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The generic OF-based host controller driver uses pci_common_init_dev(),
which is ARM-specific and requires the ARM struct hw_pci. The part of
pci_common_init_dev() that is needed is limited and can be done here
without using hw_pci.
Note that the ARM pcibios functions expect the PCI sysdata to be a pointer
to a struct pci_sys_data. Add a struct pci_sys_data as the first element
in struct gen_pci so that when we use a gen_pci pointer as sysdata, it is
also a pointer to a struct pci_sys_data.
Create and scan the root bus directly without using the ARM
pci_common_init_dev() interface.
[bhelgaas: changelog, move pcie_bus_configure_settings() before
pci_bus_add_devices(), combine !PCI_PROBE_ONLY blocks]
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Simplify a trivial if-return sequence by combining it with a preceding
function call.
The semantic patch that makes this change is available in
scripts/coccinelle/misc/simple_return.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Lucas Stach <l.stach@pengutronix.de>
Use BUG_ON() instead of an if condition followed by BUG().
The semantic patch that makes this change is available in
scripts/coccinelle/misc/bugon.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
There is no need to use the IS_ERR_VALUE() macro for checking the return
value from pm_runtime_* functions.
Test for a negative pm_runtime_get_sync() return value instead of using
IS_ERR_VALUE().
The semantic patch that makes this change is available in
scripts/coccinelle/api/pm_runtime.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
There's a typo in commit e39758e0ea in linux-next, which incorrectly
spells "msi_desc_to_pci_sysdata()" as "msi_desc_to_pci_sys_data()" and
causes build failure:
> ../drivers/pci/host/pcie-xilinx.c:235:3: error: implicit declaration
of function 'msi_desc_to_pci_sys_data' [-Werror=implicit-function-declaration]
Fixes: e39758e0ea "PCI: Use helper functions to access fields in struct msi_desc"
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Mark Brown <broonie@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Cc: Srikanth Thokala <sthokal@xilinx.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Link: http://lkml.kernel.org/r/1439912763-10645-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* pci/host-dra7xx:
ARM: dts: am57xx-evm: Add 'gpios' property with gpio2_8
PCI: dra7xx: Add support to make GPIO drive PERST# line
PCI: dra7xx: Clear MSE bit during suspend so clocks will idle
PCI: dra7xx: Add PM support
PCI: dra7xx: Disable pm_runtime on get_sync failure
* pci/host-iproc:
PCI: iproc: Allow BCMA bus driver to be built as module
PCI: iproc: Add arm64 support
PCI: iproc: Delete unnecessary checks before phy calls
* pci/hotplug:
PCI: pciehp: Remove ignored MRL sensor interrupt events
PCI: pciehp: Remove unused interrupt events
PCI: pciehp: Handle invalid data when reading from non-existent devices
PCI: Hold pci_slot_mutex while searching bus->slots list
PCI: Protect pci_bus->slots with pci_slot_mutex, not pci_bus_sem
PCI: pciehp: Simplify pcie_poll_cmd()
PCI: Use "slot" and "pci_slot" for struct hotplug_slot and struct pci_slot
* pci/iommu:
PCI: Remove pci_ats_enabled()
PCI: Stop caching ATS Invalidate Queue Depth
PCI: Move ATS declarations to linux/pci.h so they're all together
PCI: Clean up ATS error handling
PCI: Use pci_physfn() rather than looking up physfn by hand
PCI: Inline the ATS setup code into pci_ats_init()
PCI: Rationalize pci_ats_queue_depth() error checking
PCI: Reduce size of ATS structure elements
PCI: Embed ATS info directly into struct pci_dev
PCI: Allocate ATS struct during enumeration
iommu/vt-d: Cache PCI ATS state and Invalidate Queue Depth
* pci/irq:
PCI: Kill off set_irq_flags() usage
* pci/virtualization:
PCI: Add ACS quirks for Intel I219-LM/V
The PERST# line in am57x-evm is connected to a GPIO line and PERST# should
be driven high to indicate the clocks are stable (As per Figure 2-10: Power
Up of the PCIe CEM spec 3.0).
Add support to make GPIO drive PERST# line.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
DRA7xx requires the MSE bit to be cleared to set the master in standby
mode. (In DRA7xx TRM_vE, section 24.9.4.5.2.2.1 PCIe Controller Master
Standby Behavior advises to use the clearing of the local MSE bit to set
the master in standby. Without this some of the clocks do not idle).
Clear the MSE bit on suspend and enable it on resume. Clearing MSE bit is
required to get clocks to be idled after suspend.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Add PM support to pci-dra7xx so PCI clocks can be disabled during suspend
and enabled during resume without affecting PCI functionality.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Fix the error handling when pm_runtime_get_sync() fails.
If pm_runtime_get_sync() fails, call pm_runtime_disable() so there are no
unbalanced pm_runtime_enable() calls.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Change CONFIG_PCIE_IPROC_BCMA to tristate to make it possible to build this
driver as a module.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ray Jui <rjui@broadcom.com>
set_irq_flags is ARM-specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in .map()
functions, and we can simply remove the set_irq_flags calls. Some users
also modify IRQ_NOPROBE, and this has been maintained although it is not
clear that is really needed. There appears to be a great deal of blind
copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Simon Horman <horms@verge.net.au>
CC: Michal Simek <michal.simek@xilinx.com>
CC: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
* pci/host-designware:
PCI: designware: Don't complain missing *config* reg space if va_cfg0 is set
* pci/host-xgene:
PCI: xgene: Add support for a 64-bit prefetchable memory window
arm64: dts: Add APM X-Gene PCIe 64-bit prefetchable window
PCI: xgene: Drop owner assignment from platform_driver
* pci/host-xilinx:
PCI: xilinx: Check for MSI interrupt flag before handling as INTx
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Duc Dang <dhdang@apm.com>
The X-Gene MSI driver only uses the msi_controller structure as
a way to match the host bridge with its MSI HW, and thus the
msi_domain.
But now that we can directly associate an msi_domain with a device,
there is no use keeping this msi_controller around.
Just remove all traces of msi_controller from the driver.
Tested-by: Duc Dang <dhdang@apm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-19-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The current iProc BCMA front-end driver can only work on ARM32 based
platforms; therefore its config option in Kconfig should be changed to
reflect that. This fixes arm64 allmodconfig build failure when compiling
the the iProc BCMA driver that contains struct pci_sys_data that is
arm32 specific
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
PCI: iproc: Add arm64 support
Add arm64 support to the iProc PCIe driver.
Note that on arm32, bus->sysdata points to the arm32-specific
pci_sys_data struct, and pci_sys_data.private_data contains the
iproc_pcie pointer. For arm64, there's nothing corresponding to
pci_sys_data, so we keep the iproc_pcie pointer directly in
bus->sysdata.
In addition, arm64 does IRQ mapping in pcibios_add_device(), so it
doesn't need pci_fixup_irqs() as arm32 does.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently on Keystone SoCs, we always complain:
keystone-pcie 21021000.pcie: missing *config* reg space
Keystone uses an older version of DesignWare hardware that doesn't have
ATU support. So va_cfg0_base and va_cfg1_base are already set up in
ks_dw_pcie_host_init() before calling dw_pcie_host_init(), and they point
to the remote config space address va (both same for Keystone). Add a
check to avoid this boot noise on Keystone.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add arm64 support to the iProc PCIe driver.
Note that on arm32, bus->sysdata points to the arm32-specific pci_sys_data
struct, and pci_sys_data.private_data contains the iproc_pcie pointer.
For arm64, there's nothing corresponding to pci_sys_data, so we keep the
iproc_pcie pointer directly in bus->sysdata.
In addition, arm64 does IRQ mapping in pcibios_add_device(), so it doesn't
need pci_fixup_irqs() as arm32 does.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Occasionally both MSI and INTx bits in the interrupt decode register are
set at once by the Xilinx AXI PCIe Bridge, so the MSI flag in the interrupt
message should be checked to ensure that the correct handler is used.
If this check is not in place and the interrupt message type is MSI, the
INTx handler will be used erroneously when both type bits are set. This
will also be followed by a second read of the message FIFO, which can
result in the function returning early and the interrupt decode register
not being cleared if the FIFO is now empty.
Signed-off-by: Russell Joyce <russell.joyce@york.ac.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Use irq_data_get_msi_desc() to avoid redundant lookup of irq_data while we
already have a pointer to corresponding irq_data.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename irq_data_get_msi() as irq_data_get_msi_desc() to keep consistency
with other irq_data access helpers.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
platform_driver_register() automatically supplies THIS_MODULE, so we don't
need to set it in the platform_driver struct.
Remove the xgene_msi_driver.owner assignment.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The functions phy_exit() and phy_power_off() test whether their argument is
NULL and then return immediately. Thus the test around the calls is not
needed.
This issue was detected by using the Coccinelle software.
[bhelgaas: also phy_init() and phy_power_on(), as Ray Jui suggested]
[bhelgaas: also remove tests in iproc_pcie_remove()]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Pull irq fixes from Thomas Gleixner:
"This contains:
- a series of fixes for interrupt drivers to prevent a potential race
when installing a chained interrupt handler
- a fix for cpumask pointer misuse
- a fix for using the wrong interrupt number from struct irq_data
- removal of unused code and outdated comments
- a few new helper functions which allow us to cleanup the interrupt
handling code further in 4.3
I decided against doing the cleanup at the end of this merge window
and rather do the preparatory steps for 4.3, so we can run the final
ABI change at the end of the 4.3 merge window with less risk"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
ARM/LPC32xx: Use irq not hwirq for __irq_set_handler_locked()
genirq: Implement irq_set_handler_locked()/irq_set_chip_handler_name_locked()
genirq: Introduce helper irq_desc_get_irq()
genirq: Remove irq_node()
genirq: Clean up outdated comments related to include/linux/irqdesc.h
mn10300: Fix incorrect use of irq_data->affinity
MIPS/ralink: Fix race in installing chained IRQ handler
MIPS/pci: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
m68k/psc: Fix race in installing chained IRQ handler
avr32/at32ap: Fix race in installing chained IRQ handler
sh/intc: Fix race in installing chained IRQ handler
sh/intc: Fix potential race in installing chained IRQ handler
pinctrl/sun4i: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/exynos: Fix race in installing chained IRQ handler
pinctrl/st: Fix race in installing chained IRQ handler
pinctrl/adi2: Fix race in installing chained IRQ handler
...
Mohit's email-id doesn't exist anymore as he has left the company.
Replace ST's id with mohit.kumar.dhaka@gmail.com.
Signed-off-by: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Mohit Kumar <mohit.kumar.dhaka@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pratyush.anand@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with pratyush.anand@gmail.com.
Signed-off-by: Pratyush Anand <pratyush.anand@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
|
-irq_set_chained_handler(E1, E3);
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
...
|
-irq_set_chained_handler(E1, E3);
...
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
* pci/host-xgene:
PCI: xgene: Allow config access to Root Port even when link is down
PCI: xgene: Disable Configuration Request Retry Status for v1 silicon
* pci/hotplug:
PCI: pciehp: Inline the "handle event" functions into the ISR
PCI: pciehp: Rename queue_interrupt_event() to pciehp_queue_interrupt_event()
PCI: pciehp: Make queue_interrupt_event() void
PCI: pciehp: Clean up debug logging
Previously, when a Root Port's link was down, we didn't allow config access
to the Root Port, which meant that if the Root Port led to an empty slot,
"lspci" didn't even show the Root Port.
Allow config access to Root Port even when link is down.
[bhelgaas: changelog, fold in unused var fix]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When a CPU reads the Vendor and Device ID of a non-existent device, the
controller should fabricate return data of 0xFFFFFFFF. Configuration
Request Retry Status (CRS) is not applicable in this case because the
device doesn't exist at all.
The X-Gene v1 PCIe controller has a bug in the CRS logic such that when CRS
is enabled, it fabricates return data of 0xFFFF0001 for this case, which
means "the device exists but is not ready." That causes the PCI core to
retry the read until it times out after 60 seconds.
Disable CRS capability advertisement by clearing the CRS Software
Visibility bit in the Root Capabilities Register.
[bhelgaas: changelog and comment]
Tested-by: Ian Campbell <ian.campbell@citrix.com>
Tested-by: Marcin Juszkiewicz <mjuszkiewicz@redhat.com>
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tanmay Inamdar <tinamdar@apm.com>
Use "u32", not "uint32_t", for consistency. Use "tmp", not "temp", for
consistency within the driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Richard Zhu <Richard.Zhu@freescale.com>
Currently, the timeout is never detected as count has a value of -1 if a
timeout happens, but the code is checking for 0. Also, this patch removes
the unneeded final wait if a timeout occurs.
[bhelgaas: reworked starting from http://lkml.kernel.org/r/1433543864-7252-1-git-send-email-troy.kisky@boundarydevices.com]
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All the DesignWare-based host drivers loop waiting for the link to come up,
but they do it several ways that are needlessly different.
Wait for the link to come up in a consistent style across all the
DesignWare drivers. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
All other DesignWare-based drivers have a *_establish_link() function.
This functionality is trivial for Layerscape, but factor out a
ls_pcie_establish_link() for consistency with the other drivers. No
functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
All the other DesignWare-based drivers use dw_pcie_link_up(), so use it in
this driver, too, for consistency. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
We already use dw_pcie_link_up() once in dra7xx_pcie_establish_link(), but
we duplicate its code later. Use dw_pcie_link_up() for consistency. No
functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
APM X-Gene v1 SoC supports its own implementation of MSI, which is not
compliant to GIC V2M specification for MSI Termination.
There is a single MSI block in X-Gene v1 SOC which serves all 5 PCIe ports.
This MSI block supports 2048 MSI termination ports coalesced into 16
physical HW IRQ lines and shared across all 5 PCIe ports.
As there are only 16 HW IRQs to serve 2048 MSI vectors, to support
set_affinity correctly for each MSI vectors, the 16 HW IRQs are statically
allocated to 8 X-Gene v1 cores (2 HW IRQs for each cores). To steer MSI
interrupt to target CPU, MSI vector is moved around these HW IRQs lines.
With this approach, the total MSI vectors this driver supports is reduced
to 256.
[bhelgaas: squash doc, driver, maintainer update]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Rename imx6_pcie_start_link() to imx6_pcie_establish_link() to follow the
convention of other DesignWare-based host drivers. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
The resource list is only used in the setup process and was never freed.
pci_add_resource() allocates a memory area to store the list item.
Fix the memory leak.
Tested-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
The struct iproc_pcie.resources member was pointing to a stack variable and
is invalid after the registration function returned.
Remove this pointer and add a parameter to the function.
Tested-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
After b97ea289cf ("PCI: Assign resources before drivers claim devices
(pci_scan_root_bus())"), pci_scan_root_bus() no longer adds the devices, so
it is equivalent to:
pci_create_root_bus()
pci_scan_child_bus()
Use pci_scan_root_bus() to simplify the code.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Mohit Kumar <mohit.kumar@st.com>
After b97ea289cf ("PCI: Assign resources before drivers claim devices
(pci_scan_root_bus())"), pci_scan_root_bus() no longer adds the devices, so
it is equivalent to tegra_pcie_scan_bus().
Remove tegra_pcie_scan_bus() (the hw.scan method), so we use the generic
pci_scan_root_bus() path.
[bhelgaas: changelog]
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thierry Reding <treding@nvidia.com>
After b97ea289cf ("PCI: Assign resources before drivers claim devices
(pci_scan_root_bus())"), pci_scan_root_bus() no longer adds the devices, so
it is equivalent to mvebu_pcie_scan_bus().
Remove mvebu_pcie_scan_bus() (the hw.scan method), so we use the generic
pci_scan_root_bus() path. We also need to use pci_common_init_dev()
instead of pci_common_init() so we can supply the host bridge device
pointer.
[bhelgaas: changelog]
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Jason Cooper <jason@lakedaemon.net>
Most transactions' type are cfg0 and MEM, so the current iATU usage is not
balanced: iATU0 is hot while iATU1 is rarely used.
Refactor the iATU usage so we use iATU0 for cfg and IO and iATU1 for MEM.
This allocation idea comes from Minghuan Lian
<Minghuan.Lian@freescale.com>:
[bhelgaas: use link with Message-ID]
Link: http://lkml.kernel.org/r/1429091315-31891-3-git-send-email-Minghuan.Lian@freescale.com
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Currently, the outbound iATU programming functions are similar: the only
difference is index, type, addr and size. Consolidate these functions into
one. This saves about 1700 bytes in text:
text data bss dec hex filename
9276 204 4 9484 250c pcie-designware.o-before
7532 204 4 7740 1e3c pcie-designware.o
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
This driver adds support for the PCIe 2.0 controller found on the BCMA bus.
This controller can be found on (mostly) all Broadcom BCM470X / BCM5301X
ARM SoCs.
The driver found in the Broadcom SDK does some more stuff, like setting up
some DMA memory areas, chaining MPS and MRRS to 512 and also some PHY
changes like "improving" the PCIe jitter and doing some special
initialization for the 3rd PCIe port.
This was tested on a bcm4708 board with 2 PCIe ports and wireless cards
connected to them.
PCI_DOMAINS is needed by this driver, because normally there is more than
one PCIe controller and without PCI_DOMAINS only the first controller gets
registered. This controller gets 6 IRQs; the last one is trigged by all
IRQ events.
[bhelgaas: fix "GPLv2" MODULE_LICENSE typo]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Ray Jui <rjui@broadcom.com.com>
The iProc core PCIe driver defaults to using of_irq_parse_and_map_pci() for
IRQ mapping. Add iproc_pcie.map_irq so bus interfaces that don't use
device tree can override this by supplying their own IRQ mapping function.
[bhelgaas: changelog]
Posting: http://lkml.kernel.org/r/1431465781-10753-1-git-send-email-hauke@hauke-m.de
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ray Jui <rjui@broadcom.com.com>
devm_ioremap_resource() validates the resource it receives, so if we check
for devm_ioremap_resource() failure, we need not check for failure of the
preceding platform_get_resource().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Check for failure from platform_get_resource() (this check actually happens
inside devm_ioremap_resource()) before dereferencing the pointer returned
from platform_get_resource().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Check for failure of devm_ioremap_resource().
devm_ioremap_resource() validates the resource it receives, so if we check
for devm_ioremap_resource() failure, we need not check for failure of the
preceding platform_get_resource().
[bhelgaas: changelog]
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Enumeration
- Don't look for ACPI hotplug parameters if ACPI is disabled (Bjorn Helgaas)
Resource management
- Revert "sparc/PCI: Clip bridge windows to fit in upstream windows" (Bjorn Helgaas)
AER
- Avoid info leak in __print_tlp_header() (Rasmus Villemoes)
PCI device hotplug
- Add missing curly braces in cpci_configure_slot() (Dan Carpenter)
ST Microelectronics SPEAr13xx host bridge driver
- Drop __initdata from spear13xx_pcie_driver (Matwey V. Kornilov)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ituX
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.0-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Here are some fixes for v4.0. I apologize for how late they are. We
were hoping for some better fixes, but couldn't get them polished in
time. These fix:
- a Xen domU oops with PCI passthrough devices
- a sparc T5 boot failure
- a STM SPEAr13xx crash (use after initdata freed)
- a cpcihp hotplug driver thinko
- an AER thinko that printed stack junk
Details:
Enumeration
- Don't look for ACPI hotplug parameters if ACPI is disabled (Bjorn Helgaas)
Resource management
- Revert "sparc/PCI: Clip bridge windows to fit in upstream windows" (Bjorn Helgaas)
AER
- Avoid info leak in __print_tlp_header() (Rasmus Villemoes)
PCI device hotplug
- Add missing curly braces in cpci_configure_slot() (Dan Carpenter)
ST Microelectronics SPEAr13xx host bridge driver
- Drop __initdata from spear13xx_pcie_driver (Matwey V. Kornilov)
* tag 'pci-v4.0-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "sparc/PCI: Clip bridge windows to fit in upstream windows"
PCI: Don't look for ACPI hotplug parameters if ACPI is disabled
PCI: cpcihp: Add missing curly braces in cpci_configure_slot()
PCI/AER: Avoid info leak in __print_tlp_header()
PCI: spear: Drop __initdata from spear13xx_pcie_driver
Use a semicolon, not a comma, to terminate a statement.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for the Broadcom iProc PCIe controller.
pcie-iproc.c is the common core driver, and a front-end bus interface needs
to be added to support different bus interfaces.
pcie-iproc-platform.c contains the support for the platform bus interface.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add suspend/resume support for the mvebu PCIe host driver. Without this
commit, the system will panic at resume time when PCIe devices are
connected.
Note that we have to use the ->suspend_noirq() and ->resume_noirq() hooks,
because at resume time, the PCI fixups are done at ->resume_noirq() time,
so the PCIe controller has to be ready at this point.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Previously, pci_scan_root_bus() created a root PCI bus, enumerated the
devices on it, and called pci_bus_add_devices(), which made the devices
available for drivers to claim them.
Most callers assigned resources to devices after pci_scan_root_bus()
returns, which may be after drivers have claimed the devices. This is
incorrect; the PCI core should not change device resources while a driver
is managing the device.
Remove pci_bus_add_devices() from pci_scan_root_bus() and do it after any
resource assignment in the callers.
Note that ARM's pci_common_init_dev() already called pci_bus_add_devices()
after pci_scan_root_bus(), so we only need to remove the first call:
pci_common_init_dev
pcibios_init_hw
pci_scan_root_bus
pci_bus_add_devices # first call
pci_bus_assign_resources
pci_bus_add_devices # second call
[bhelgaas: changelog, drop "root_bus" var in alpha common_init_pci(),
return failure earlier in mn10300, add "return" in x86 pcibios_scan_root(),
return early if xtensa platform_pcibios_fixup() fails]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
CC: Matt Turner <mattst88@gmail.com>
CC: David Howells <dhowells@redhat.com>
CC: Tony Luck <tony.luck@intel.com>
CC: Michal Simek <monstr@monstr.eu>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
CC: Sebastian Ott <sebott@linux.vnet.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Chris Metcalf <cmetcalf@ezchip.com>
CC: Chris Zankel <chris@zankel.net>
CC: Max Filippov <jcmvbkbc@gmail.com>
CC: Thomas Gleixner <tglx@linutronix.de>
APM X-Gene host bridge driver
- Add register offset to config space base address (Feng Kan)
Miscellaneous
- Don't read past the end of sysfs "driver_override" buffer (Sasha Levin)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4mzw
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.0-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Here are a couple updates for v4.0.
One fixes a config accessor problem on APM X-Gene that we introduced
when switching to generic config accessors, and the other fixes an
older read-past-end-of-buffer problem in sysfs.
APM X-Gene host bridge driver
- Add register offset to config space base address (Feng Kan)
Miscellaneous
- Don't read past the end of sysfs "driver_override" buffer (Sasha Levin)"
* tag 'pci-v4.0-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: xgene: Add register offset to config space base address
PCI: Don't read past the end of sysfs "driver_override" buffer
Struct spear13xx_pcie_driver was in initdata, but we passed a pointer to it
to platform_driver_register(), which can use the pointer at arbitrary times
in the future, even after the initdata is freed. That leads to crashes.
Move spear13xx_pcie_driver and things referenced by it
(spear13xx_pcie_probe() and dw_pcie_host_init()) out of initdata.
[bhelgaas: changelog]
Fixes: 6675ef212d ("PCI: spear: Fix Section mismatch compilation warning for probe()")
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
CC: stable@vger.kernel.org # v3.17+
In xgene_pcie_map_bus(), we neglected to add in the register offset when
calculating the config space address. This means all config accesses
operated on the first four bytes of config space.
Add the register offset to the config space base address.
Also correct the xgene_pcie_map_bus() prototype to fix a compiler warning.
[bhelgaas: changelog]
Fixes: 350f8be5bb ("PCI: xgene: Convert to use generic config accessors")
Posting: http://lkml.kernel.org/r/1424214840-26498-1-git-send-email-fkan@apm.com
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tanmay Inamdar <tinamdar@apm.com>
Acked-by: Rob Herring <robh@kernel.org>
In Linux 4.0-rc1 ARM Versatile PCI build fails to build due to what
appears to be an API update. This patch is a very simple correction,
merely posted as a heads-up to the maintainers. Hopefully a better
fix can be forwarded to Linus.
[ arnd: the patch actually looks correct, so let's take this version ]
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The lower 16 bits of the address, which is managed by mem_res, need to be
zero. Check the address to verify this.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
PCIEPARL and PCIEPARH are macros that calculate register addresses.
However, the register names are incorrect. Change them to PCIEPALR and
PCIEPAUR.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The lower 7 bits of PCIEPARL are reserved. When we write to this register,
these bits must be 0.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
David Daney