In s3c24xx_serial_console_setup function, if the uart port that is
being setup as a console has not been initialized, an error can be
returned instead of using uart port 0 as the default console port.
The uart port that was intended to be used as a console could be
initialized at a later point during boot and then registered as a
console. This will avoid using uart port 0 as a unintended console
port.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'at91/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-2.6-arm-soc:
AT91: Change nand buswidth logic to match hardware default configuration
at91: Use "pclk" as con_id on at91cap9 and at91rm9200
at91: fix udc, ehci and mmc clock device name for cap9/9g45/9rl
atmel_serial: fix internal port num
at91: fix at91_set_serial_console: use platform device id
Unthrottling the TTY during close ends up enabling interrupts
on a device not on the active list, which will never have the
interrupts cleared. Doctor, it hurts when I do this.
>>> On 6/2/2011 at 01:56 AM, in message <20110601145608.3e586e16@bob.linux.org.uk>, Alan Cox <alan@linux.intel.com> wrote:
> On Wed, 01 Jun 2011 10:34:07 +1200
> "andrew mcgregor" <andrew.mcgregor@alliedtelesis.co.nz> wrote:
> > The LKML message
> > http://kerneltrap.org/mailarchive/linux-kernel/2010/2/25/4541847 from
> > February doesn't seem to have been resolved since. We struck the
> > issue, and the patch below (against 2.6.32) fixes it. Should I
> > supply a patch against 3.0.0rc?
>
> I think that would be sensible. I don't actually see how you hit it as
> the IRQ ought to be masked by then but it's certainly wrong for n_tty
> to be calling into check_unthrottle at that point.
>
> So yes please send a patch with a suitable Signed-off-by: line to
> linux-serial and cc GregKH <greg@kroah.com> as well.
>
> Alan
Signed-off-by: Andrew McGregor <andrew.mcgregor@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch "modernize" tty/serial/samsung.c to use non-legacy code for
suspend/resume.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kconfig allows enabling console support for the SC26xx driver even when
it's configured as a module resulting in a:
ERROR: "uart_console_device" [drivers/tty/serial/sc26xx.ko] undefined!
modpost error since the driver was merged in
eea63e0e8a [SC26XX: New serial driver for
SC2681 uarts] in 2.6.25. Fixed by only allowing console support to be
enabled if the driver is builtin.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: stable <stable@kernel.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver went to initialize its waitqueue at the start of the main processing
thread. However, it is possible that this thread is not scheduled on a CPU
before the write function is called which leads to a following error:
BUG: spinlock bad magic on CPU#1, swapper/1
lock: f5f3ebdc, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
Pid: 1, comm: swapper Not tainted 3.0.0-rc2+ #67
Call Trace:
[<c1289663>] spin_bug+0xa3/0xf0
[<c12897ad>] do_raw_spin_lock+0x7d/0x150
[<c1490006>] ? init_idle+0x8d/0x20c
[<c14963de>] _raw_spin_lock_irqsave+0x4e/0x60
[<c102f2bb>] ? __wake_up+0x1b/0x50
[<c102f2bb>] __wake_up+0x1b/0x50
[<c12d03bc>] ? uart_console_write+0x4c/0x60
[<c12d36c0>] ? serial_m3110_enable_ms+0x10/0x10
[<c12d3715>] serial_m3110_con_write+0x55/0x60
[<c1041575>] __call_console_drivers+0x75/0x90
[<c10415d9>] _call_console_drivers+0x49/0x80
[<c1041baa>] console_unlock+0xca/0x1f0
[<c10420ef>] vprintk+0x18f/0x4f0
[<c10787cb>] ? trace_hardirqs_on+0xb/0x10
[<c14928a3>] printk+0x18/0x1a
[<c1042730>] register_console+0x2e0/0x350
[<c12d098e>] uart_add_one_port+0x33e/0x3d0
[<c10787cb>] ? trace_hardirqs_on+0xb/0x10
[<c103e10b>] ? try_to_wake_up+0x18b/0x250
[<c1485ba6>] serial_m3110_probe+0x1c2/0x1df
[<c12d3d20>] ? serial_m3110_suspend+0x40/0x40
[<c1303db7>] spi_drv_probe+0x17/0x20
...
We fix this by initializing the waitqueue before the main thread is created.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change print message to notice instead of error to clean up
non critcal messages showing on startup. The MAX3111 not being present
is a normal path for end user systems.
Signed-off-by: William Douglas <william.douglas@intel.com>
[rebased on 3.0, switched to dev_dbg()]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch addes delay loop on fifo reset function for UART.
On high speed freq, it needs delay function when fifo reset.
If not, system will hang by this uart reset problem when resuming
from suspend mode.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 4539c24fe4 "tty/serial: Add
explicit PORT_TEGRA type" introduced separate flags describing the need
for IER bits UUE and RTOIE. Both bits are required for the XSCALE port
type. While that patch updated uart_config[] as required, the auto-probing
code wasn't updated to set the RTOIE flag when an XSCALE port type was
detected. This caused such ports to stop working. This patch rectifies
that.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: stable <stable@kernel.org> [3.0]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This doesn't cause any real bugs, but it should still be fixed.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited().
Signed-off-by: Manuel Zerpies <manuel.f.zerpies@ww.stud.uni-erlangen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The gsm_mux is created/destroyed when ldisc is
opened/closed but clients of the MUX channel devices (gsmttyN)
may access this structure as long as the TTYs are open.
For the open, the ldisc open is guaranteed to preceed the TTY open,
but the close has no such guaranteed ordering. As a result,
the gsm_mux can be freed in the ldisc close before being accessed
by one of the TTY clients. This can happen if the ldisc is removed
while there are open, active MUX channels.
A similar situation exists for DLCI-0, it is basically a resource
shared by MUX and DLCI , and should not be freed while they can
be accessed
To avoid this, gsm_mux and dlcis now have a reference counter
ldisc open takes a reference on the mux and all the dlcis
gsmtty_open takes a reference on the mux, dlci0 and its specific
dlci. Dropping the last reference initiates the actual free.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the ability to open a network data connection over a mux
virtual tty channel. This is for modems that support data connections
with raw IP frames instead of PPP. On high speed data connections this
eliminates a significant amount of PPP overhead. To use this interface,
the application must first tell the modem to open a network connection on
a virtual tty. Once that has been accomplished, the app will issue an
IOCTL on that virtual tty to create the network interface. The IOCTL will
return the index of the interface created.
The two IOCTL commands are:
ioctl( fd, GSMIOC_ENABLE_NET );
ioctl( fd, GSMIOC_DISABLE_NET );
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The n_gsm driver being an ldisc, does not provide a convenient method
e.g. udev to create the tty device nodes automatically when the ldisc
is opened.
The TTY device nodes are now created via calls to tty_register_device
from the ldisc open.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A mix of think & mismerge on my side caused a problem where both the
new hvsi_lib and the old hvsi driver gets compiled and try to define
symbols with the same name.
This fixes it by renaming the hvsi_lib exported symbols.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some platforms e.g. TI Davinci require 32-bit accesses to the UARTs.
The of_serial driver currently registers all UARTs as UPIO_MEM. Add a
new attribute "reg-io-width" to allow the port to be registered with
different IO width requirements.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
On pseries machines, consoles are provided by the hypervisor using
a low level get_chars/put_chars type interface. However, this is
really just a transport to the service processor which implements
them either as "raw" console (networked consoles, HMC, ...) or as
"hvsi" serial ports.
The later is a simple packet protocol on top of the raw character
interface that is supposed to convey additional "serial port" style
semantics. In practice however, all it does is provide a way to
read the CD line and set/clear our DTR line, that's it.
We currently implement the "raw" protocol as an hvc console backend
(/dev/hvcN) and the "hvsi" protocol using a separate tty driver
(/dev/hvsi0).
However this is quite impractical. The arbitrary difference between
the two type of devices has been a major source of user (and distro)
confusion. Additionally, there's an additional mini -hvsi implementation
in the pseries platform code for our low level debug console and early
boot kernel messages, which means code duplication, though that low
level variant is impractical as it's incapable of doing the initial
protocol negociation to establish the link to the FSP.
This essentially replaces the dedicated hvsi driver and the platform
udbg code completely by extending the existing hvc_vio backend used
in "raw" mode so that:
- It now supports HVSI as well
- We add support for hvc backend providing tiocm{get,set}
- It also provides a udbg interface for early debug and boot console
This is overall less code, though this will only be obvious once we
remove the old "hvsi" driver, which is still available for now. When
the old driver is enabled, the new code still kicks in for the low
level udbg console, replacing the old mini implementation in the platform
code, it just doesn't provide the higher level "hvc" interface.
In addition to producing generally simler code, this has several benefits
over our current situation:
- The user/distro only has to deal with /dev/hvcN for the hypervisor
console, avoiding all sort of confusion that has plagued us in the past
- The tty, kernel and low level debug console all use the same code
base which supports the full protocol establishment process, thus the
console is now available much earlier than it used to be with the
old HVSI driver. The kernel console works much earlier and udbg is
available much earlier too. Hackers can enable a hard coded very-early
debug console as well that works with HVSI (previously that was only
supported for the "raw" mode).
I've tried to keep the same semantics as hvsi relative to how I react
to things like CD changes, with some subtle differences though:
- I clear DTR on close if HUPCL is set
- Current hvsi triggers a hangup if it detects a up->down transition
on CD (you can still open a console with CD down). My new implementation
triggers a hangup if the link to the FSP is severed, and severs it upon
detecting a up->down transition on CD.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Embed the struct hvsi_header in the various packet definitions
rather than open coding it multiple times. Will help provide
stronger type checking.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This moves various HVSI protocol definitions from the hvsi.c
driver to a header file that can be used later on by a udbg
implementation
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
serial: bcm63xx_uart: fix irq storm after rx fifo overrun.
amba pl011: platform data for reg lockup and glitch v2
amba pl011: workaround for uart registers lockup
tty: n_gsm: improper skb_pull() use was leaking framed data
tty: n_gsm: Fixed logic to decode break signal from modem status
TTY: ntty, add one more sanity check
TTY: ldisc, do not close until there are readers
8250: Fix capabilities when changing the port type
8250_pci: Fix missing const from merges
ARM: SAMSUNG: serial: Fix on handling of one clock source for UART
serial: ioremap warning fix for jsm driver.
8250_pci: add -ENODEV code for Intel EG20T PCH
Presently these were all using the same static string with no regard to
dev_name() and the like. This implements a bit of rework to name the IRQ
dynamically, as it should have been doing all along anyways.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Ultimately we want everything to be going through the clock framework and
runtime pm, so kill off the per-port callbacks that enabled ports to
bypass the common infrastructure.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
the atmel_ports is link to the console number and not the device id
this was not detected on at91 as we always register the dbgu on the console
as ttyS0
tested on at91sam9263 by setting the dbgu as ttyS1 and use as console
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index 70e5646..9b8a14f 100644
- a/arch/arm/mach-at91/board-sam9263ek.c
+ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -58,14 +58,14 @@ static void __init ek_init_early(void)
/* Initialize processor: 16.367 MHz crystal */
at91_initialize(16367660);
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
+ /* DBGU on ttyS1. (Rx & Tx only) */
+ at91_register_uart(0, 1, 0);
- /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
- at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
+ /* USART0 on ttyS0. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9263_ID_US0, 0, ATMEL_UART_CTS | ATMEL_UART_RTS);
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
+ /* set serial console to ttyS1 (ie, DBGU) */
+ at91_set_serial_console(1);
}
/*
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
The driver went to initialize its waitqueue at the start of the main
processing thread. However, it is possible that this thread is not
scheduled on a CPU before the write function is called which leads to a
following error:
BUG: spinlock bad magic on CPU#1, swapper/1
lock: f5f3ebdc, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
Pid: 1, comm: swapper Not tainted 3.0.0-rc2+ #67
Call Trace:
[<c1289663>] spin_bug+0xa3/0xf0
[<c12897ad>] do_raw_spin_lock+0x7d/0x150
[<c14963de>] _raw_spin_lock_irqsave+0x4e/0x60
[<c102f2bb>] __wake_up+0x1b/0x50
[<c12d3715>] serial_m3110_con_write+0x55/0x60
[<c1041575>] __call_console_drivers+0x75/0x90
[<c10415d9>] _call_console_drivers+0x49/0x80
[<c1041baa>] console_unlock+0xca/0x1f0
[<c10420ef>] vprintk+0x18f/0x4f0
[<c14928a3>] printk+0x18/0x1a
[<c1042730>] register_console+0x2e0/0x350
[<c12d098e>] uart_add_one_port+0x33e/0x3d0
[<c1485ba6>] serial_m3110_probe+0x1c2/0x1df
[<c1303db7>] spi_drv_probe+0x17/0x20
...
Fix this by initializing the waitqueue before the main thread is
created.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change print message to notice instead of error to clean up non critical
messages showing on startup. The MAX3111 not being present is a normal
path for end user systems.
Signed-off-by: William Douglas <william.douglas@intel.com>
[rebased on 3.0, switched to dev_dbg()]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).
To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.
Hope people are OK with tiny include file.
Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround aims to break the deadlock situation
which raises during continuous transfer of data for long
duration over uart with hardware flow control. It is
observed that CTS interrupt cannot be cleared in uart
interrupt register (ICR). Hence further transfer over
uart gets blocked.
It is seen that during such deadlock condition ICR
don't get cleared even on multiple write. This leads
pass_counter to decrease and finally reach zero. This
can be taken as trigger point to run this UART_BT_WA.
Workaround backups the register configuration, does soft
reset of UART using BIT-0 of PRCC_K_SOFTRST_SET/CLEAR
registers and restores the registers.
This patch also provides support for uart init and exit
function calls if present.
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
gsm_dlci_data_output_framed() was doing:
memcpy(dp, skb_pull(dlci->skb, len), len);
The problem is skb_pull() returns the post-increment data ptr
so the first chunk of dlci->skb->data is leaked.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The modem status can be one or 2 octets and contains the V.24 signals
and in the 2 octet case also the break signal.
We were improperly decoding the break signal from the modem in the
2 octet case.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If dmi_get_system_info() returns NULL, pch_uart_init_port() will
dereferencea a zero pointer.
This oops was observed on an Atom based board which has no BIOS, but
a bootloder which doesn't provide DMI data.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Greg KH <gregkh@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For all ports with a valid SCLSR register we can use the generic FIFO
overrun detection logic. Test the validity of the SCLSR register rather
than depending explicitly on port type, which can be ambiguous for the
SCIFA/B types.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates all of the TX/RX fill/room nonsense in to a single set
of fairly heavyweight definitions. The implementation goes in descending
order of complexity, testing the register map for capabilities until we
run out of options and do it the legacy SCI way. Masks are derived
directly from the per-port FIFO size, meaning that platforms with FIFO
sizes not matching the standard port types will still need to manually
fix them up.
This also fixes up a number of issues such as tx_empty being completely
bogus for SCI and IrDA ports, some ports using masks smaller or greater
than their FIFO size, and so forth.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This takes a bit of a sledgehammer to the horribly CPU subtype
ifdef-ridden header and abstracts all of the different register layouts
in to distinct types which in turn can be overriden on a per-port basis,
or permitted to default to the map matching the port type at probe time.
In the process this ultimately fixes up inumerable bugs with mismatches
on various CPU types (particularly the legacy ones that were obviously
broken years ago and no one noticed) and provides a more tightly coupled
and consolidated platform for extending and implementing generic
features.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The flush_to_ldisc() work entry has special logic to notice when it has
seen the original tail of the data queue, and it avoids continuing the
flush if it sees that _original_ tail rather than the current tail.
This logic can trigger in case somebody is constantly adding new data to
the tty while the flushing is active - and the intent is to avoid
excessive CPU usage while flushing the tty, especially as we used to do
this from a softirq context which made it non-preemptible.
However, since we no longer re-arm the work-queue from within itself
(because that causes other trouble: see commit a5660b41af "tty: fix
endless work loop when the buffer fills up"), this just leads to
possible hung tty's (most easily seen in SMP and with a test-program
that floods a pty with data - nobody seems to have reported this for any
real-life situation yet).
And since the workqueue isn't done from timers and softirq's any more,
it's doubtful whether the CPU useage issue is really relevant any more.
So just remove the logic entirely, and see if anybody ever notices.
Alternatively, we might want to re-introduce the "re-arm the work" for
just this case, but then we'd have to re-introduce the delayed work
model or some explicit timer, which really doesn't seem worth it for
this.
Reported-and-tested-by: Guillaume Chazarain <guichaz@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Non-SCI parts do not have the special port reg necessary for cases where
the RX and SCI pins are muxed and need to be manually polled, so these
like always fall back on the normal FIFO processing paths. SH7760 is in a
class in and of itself with regards to mapping its SIM card interface via
the SCI port class despite not having any of the RXD lines wired up and
so implicitly behaving more like a SCIF in this regard. Out of the other
CPUs, some support the port check via the same block while others do it
through an external SuperI/O, so it's not even possible to perform the
check relative to the ioremapped cookie offset, so the separate read
semantics are preserved here, too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates all of the broken out overrun handling and ensures that
we have sensible defaults per-port type, in addition to making sure that
overruns are flagged appropriately in the error mask for parts that
haven't explicitly disabled support for it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the previous patch, we fixed another bug where read_buf was freed
while we still was in n_tty_read. We currently check whether read_buf
is NULL at the start of the function. Add one more check after we wake
up from waiting for input.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We restored tty_ldisc_wait_idle in 100eeae2c5 (TTY: restore
tty_ldisc_wait_idle). We used it in the ldisc changing path to fix the
case where there are tasks in n_tty_read waiting for data and somebody
tries to change ldisc.
Similar to the case above, there may be also tasks waiting in
n_tty_read while hangup is performed. As 65b770468e (tty-ldisc: turn
ldisc user count into a proper refcount) removed the wait-until-idle
from all paths, hangup path won't wait for them to disappear either
now. So add it back even to the hangup path.
There is a difference, we need uninterruptible sleep as there is
obviously HUP signal pending. So tty_ldisc_wait_idle now sleeps
without possibility to be interrupted. This is what original
tty_ldisc_wait_idle did. After the wait idle reintroduction
(100eeae2c5), we have had interruptible sleeps for the ldisc changing
path. But as there is a 5s timeout anyway, we don't allow it to be
interrupted from now on. It's not worth the added complexity of
deciding what kind of sleep we want.
Before 65b770468e tty_ldisc_release was called also from
tty_ldisc_release. It is called from tty_release, so I don't think we
need to restore that one.
This is nicely reproducible after constifying the timing when
drivers/tty/n_tty.c is patched as follows ("TTY: ntty, add one more
sanity check" patch is needed to actually see it explode):
%% -1548,6 +1549,7 @@ static int n_tty_open(struct tty_struct *tty)
/* These are ugly. Currently a malloc failure here can panic */
if (!tty->read_buf) {
+ msleep(100);
tty->read_buf = kzalloc(N_TTY_BUF_SIZE, GFP_KERNEL);
if (!tty->read_buf)
return -ENOMEM;
%% -1785,6 +1788,7 @@ do_it_again:
break;
}
timeout = schedule_timeout(timeout);
+ msleep(20);
continue;
}
__set_current_state(TASK_RUNNING);
===== With a process: =====
while (1) {
int fd = open(argv[1], O_RDWR);
read(fd, buf, sizeof(buf));
close(fd);
}
===== and its child: =====
setsid();
while (1) {
int fd = open(tty, O_RDWR|O_NOCTTY);
ioctl(fd, TIOCSCTTY, 1);
vhangup();
close(fd);
usleep(100 * (10 + random() % 1000));
}
===== EOF =====
References: https://bugzilla.novell.com/show_bug.cgi?id=693374
References: https://bugzilla.novell.com/show_bug.cgi?id=694509
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org> [32, 33, 34, 39]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With virtual machines like qemu, it's pretty common to see "too much
work for irq4" messages nowadays. This happens when a bunch of output
is printed on the emulated serial console. This is caused by too low
PASS_LIMIT. When ISR loops more than the limit, it spits the message.
I've been using a kernel with doubled the limit and I couldn't see no
problems. Maybe it's time to get rid of the message now?
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The purpose of the patch is to add EEH support to the 8250_PCI driver
for the IBM/Digi PCIE 2port Async EIA-232 Adapter that uses a PLX
chipset on the PPC platforrm. Basic support for this adapter was
recently added https://lkml.org/lkml/2011/5/11/341
This patch was created against the linux-next kernel
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <scottk@digi.com>
Signed-off-by: Michael Reed <mreed@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Timedia/SUNIX PCI cards with both serial and parallel ports are
currently supported by 8250_pci and parport_pc individually. Moving
that support into parport_serial allows using both types of ports at the
same time.
This was successfully tested with a SUNIX 4079T.
Signed-off-by: Frédéric Brière <fbriere@fbriere.net>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-parport@lists.infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function, if present, is called early on by the 8250_pci probe; it
can be used to reject devices meant for parport_serial. (The .init
function cannot be used for this purpose, as it is also called by
parport_serial.)
Signed-off-by: Frédéric Brière <fbriere@fbriere.net>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-parport@lists.infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add I/O based support for serial and parallel ports of the following
chips:
Vendor: Moschip (0x9710)
Parts (device IDs)
* 9900 (0x9900)
* 9904 (0x9904
* 9901 (0x9912, also sold as 9912)
* 9922 (0x9922)
On all chips but the 9900, a single port is provided per PCI subdevice
(subvendor-ID 0xA000, subdevice-IDs 0x1000 for serial, 0x2000 for
parallel with proper class codes). In cascading configurations, the
9900 provides two devices per subdevice, with subvendor-ID 0xA000 and
subdevice-IDs 0x30ps where p is the number of parallel ports and s the
number of serial ports.
Basic testing was only done on the serial part of a 9912 to the point
where it can be used for a serial kernel console, and advanced features
are completely untested. It is possible to reduce functionality of the
chips by adding a configuration EEPROM, and the datasheet [1] is
inconsistent w.r.t subdevices in the 4s+2s1p and 2s1p+4s
configurations. The subdevice-ID 0x3012 should likely read 0x3011 with
a serial port in function 3, which would be consistent with the BAR
layouts. For now, the drivers ignore subdevices with ID 0x1000 and no
class code.
The parallel ports are integrated in parport_serial even for purely
parallel parts to reduce the footprint of the patch.
[1] http://www.moschip.com/data/products/MCS9900/MCS9900_Datasheet.pdf
Signed-off-by: Nicos Gollan <gtdev@spearhead.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When changing the port type, the capabilities flags should be changed
also, otherwise the capabilities will not correspond to the port type,
which make set_sleep() crash on rmmod.
This patch just assign the correct capabilites when the port changes.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
CC: Michael Reed <mreed@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the way of comparison for handling of two or more
clock sources for UART.
For example, if just only one clock source is defined even though
there are two clock sources for UART, the serial driver does not
set proper clock up. Of course, it is problem.
So this patch changes the condition of comparison to avoid useless
setup clock and adds a flag 'NO_NEED_CHECK_CLKSRC' which means
selection of source clock is not required.
In addition, since the Exynos4210 has only one clock source for UART
this patch adds the flag into its common_init_uarts().
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I saw a warning about ioremap from the jsm driver on a system which
looked like this:
resource map sanity check conflict: 0xe0200800 0xe02017ff 0xe0200800 0xe0200fff 0000:01:08.0
Turns out the warning is valid. The jsm driver has been asking to ioremap
0x1000 forever, but in fact only 8 port chips have 0x1000 bytes of memory.
4 port chips have 0x800 and 2 port chips have 0x400 according to the
data sheet. It makes more sense to map the size of the region rather
than a hard coded value. If you happen to have the region legitimately
mapped to a base address that is not 4K aligned, ioremap complains
otherwise.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
h8300 has never been updated upstream to support the conversion to the
driver model (which happened mid-2.5), and it doesn't seem likely that it
ever will. Kill off the remaining bitrotted support to reduce the
maintenance burden going forward.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reverts commit b1c43f82c5.
It was broken in so many ways, and results in random odd pty issues.
It re-introduced the buggy schedule_work() in flush_to_ldisc() that can
cause endless work-loops (see commit a5660b41af6a: "tty: fix endless
work loop when the buffer fills up").
It also used an "unsigned int" return value fo the ->receive_buf()
function, but then made multiple functions return a negative error code,
and didn't actually check for the error in the caller.
And it didn't actually work at all. BenH bisected down odd tty behavior
to it:
"It looks like the patch is causing some major malfunctions of the X
server for me, possibly related to PTYs. For example, cat'ing a
large file in a gnome terminal hangs the kernel for -minutes- in a
loop of what looks like flush_to_ldisc/workqueue code, (some ftrace
data in the quoted bits further down).
...
Some more data: It -looks- like what happens is that the
flush_to_ldisc work queue entry constantly re-queues itself (because
the PTY is full ?) and the workqueue thread will basically loop
forver calling it without ever scheduling, thus starving the consumer
process that could have emptied the PTY."
which is pretty much exactly the problem we fixed in a5660b41af.
Milton Miller pointed out the 'unsigned int' issue.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Milton Miller <miltonm@bga.com>
Cc: Stefan Bigler <stefan.bigler@keymile.com>
Cc: Toby Gray <toby.gray@realvnc.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel EG20T PCH has UART device which is compatible with 8250.
Currently, with general configuration, the PCH UART driver is not loaded
but 8250 standard driver is loaded. Therefore, in case of using PCH
UART driver, need to disable 8250 pci function. However, this procedure
is not best solution. This patch, in 8250_pci, if the device is the PCH
or the family IOH, '-ENODEV' is returned. As a result, disabling
8250-pci processing becomes unnecessary.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (45 commits)
ARM: 6945/1: Add unwinding support for division functions
ARM: kill pmd_off()
ARM: 6944/1: mm: allow ASID 0 to be allocated to tasks
ARM: 6943/1: mm: use TTBR1 instead of reserved context ID
ARM: 6942/1: mm: make TTBR1 always point to swapper_pg_dir on ARMv6/7
ARM: 6941/1: cache: ensure MVA is cacheline aligned in flush_kern_dcache_area
ARM: add sendmmsg syscall
ARM: 6863/1: allow hotplug on msm
ARM: 6832/1: mmci: support for ST-Ericsson db8500v2
ARM: 6830/1: mach-ux500: force PrimeCell revisions
ARM: 6829/1: amba: make hardcoded periphid override hardware
ARM: 6828/1: mach-ux500: delete SSP PrimeCell ID
ARM: 6827/1: mach-netx: delete hardcoded periphid
ARM: 6940/1: fiq: Briefly document driver responsibilities for suspend/resume
ARM: 6938/1: fiq: Refactor {get,set}_fiq_regs() for Thumb-2
ARM: 6914/1: sparsemem: fix highmem detection when using SPARSEMEM
ARM: 6913/1: sparsemem: allow pfn_valid to be overridden when using SPARSEMEM
at91: drop at572d940hf support
at91rm9200: introduce at91rm9200_set_type to specficy cpu package
at91: drop boot_params and PLAT_PHYS_OFFSET
...
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
gfs2: Drop __TIME__ usage
isdn/diva: Drop __TIME__ usage
atm: Drop __TIME__ usage
dlm: Drop __TIME__ usage
wan/pc300: Drop __TIME__ usage
parport: Drop __TIME__ usage
hdlcdrv: Drop __TIME__ usage
baycom: Drop __TIME__ usage
pmcraid: Drop __DATE__ usage
edac: Drop __DATE__ usage
rio: Drop __DATE__ usage
scsi/wd33c93: Drop __TIME__ usage
scsi/in2000: Drop __TIME__ usage
aacraid: Drop __TIME__ usage
media/cx231xx: Drop __TIME__ usage
media/radio-maxiradio: Drop __TIME__ usage
nozomi: Drop __TIME__ usage
cyclades: Drop __TIME__ usage
alpha allmodconfig:
drivers/tty/serial/pch_uart.c: In function 'dma_handle_tx':
drivers/tty/serial/pch_uart.c:873: error: implicit declaration of function 'kzalloc'
drivers/tty/serial/pch_uart.c:873: warning: assignment makes pointer from integer without a cast
drivers/tty/serial/pch_uart.c: In function 'pch_uart_init_port':
drivers/tty/serial/pch_uart.c:1403: warning: assignment makes pointer from integer without a cast
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Architectures that implement their own show_mem() function did not pass
the filter argument to show_free_areas() to appropriately avoid emitting
the state of nodes that are disallowed in the current context. This patch
now passes the filter argument to show_free_areas() so those nodes are now
avoided.
This patch also removes the show_free_areas() wrapper around
__show_free_areas() and converts existing callers to pass an empty filter.
ia64 emits additional information for each node, so skip_free_areas_zone()
must be made global to filter disallowed nodes and it is converted to use
a nid argument rather than a zone for this use case.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: James Bottomley <jejb@parisc-linux.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
specify the port num via platform_data this will allow to match the clock
with the plaform_dev staticaly
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: Make struct pcmcia_device_id const, sound drivers edition
staging: pcmcia: Convert pcmcia_device_id declarations to const
pcmcia: Convert pcmcia_device_id declarations to const
pcmcia: Make declaration and uses of struct pcmcia_device_id const
pcmcia/sa1100: put sa11x0_pcmcia_hw_init[] to .devinit.data
* 'sh-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: Ignore R_SH_NONE module relocations.
SH: SE7751: Fix pcibios_map_platform_irq prototype.
sh: remove warning and warning_symbol from struct stacktrace_ops
sh: wire up sys_sendmmsg.
clocksource: sh_tmu: Runtime PM support
clocksource: sh_tmu: __clocksource_updatefreq_hz() update
clocksource: sh_cmt: Runtime PM support
clocksource: sh_cmt: __clocksource_updatefreq_hz() update
dmaengine: shdma: synchronize RCU before freeing, simplify spinlock
dmaengine: shdma: add runtime- and system-level power management
dmaengine: shdma: fix locking
sh: sh-sci: sh7377 and sh73a0 build fixes
sh: cosmetic improvement: use an existing pointer
serial: sh-sci: suspend/resume wakeup support V2
serial: sh-sci: Runtime PM support
sh: select IRQ_FORCED_THREADING.
sh: intc: Set virtual IRQs as nothread.
sh: fixup fpu.o compile order
i2c: add a module alias to the sh-mobile driver
ALSA: add a module alias to the FSI driver
...
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (48 commits)
serial: 8250_pci: add support for Cronyx Omega PCI multiserial board.
tty/serial: Fix break handling for PORT_TEGRA
tty/serial: Add explicit PORT_TEGRA type
n_tracerouter and n_tracesink ldisc additions.
Intel PTI implementaiton of MIPI 1149.7.
Kernel documentation for the PTI feature.
export kernel call get_task_comm().
tty: Remove to support serial for S5P6442
pch_phub: Support new device ML7223
8250_pci: Add support for the Digi/IBM PCIe 2-port Adapter
ASoC: Update cx20442 for TTY API change
pch_uart: Support new device ML7223 IOH
parport: Use request_muxed_region for IT87 probe and lock
tty/serial: add support for Xilinx PS UART
n_gsm: Use print_hex_dump_bytes
drivers/tty/moxa.c: Put correct tty value
TTY: tty_io, annotate locking functions
TTY: serial_core, remove superfluous set_task_state
TTY: serial_core, remove invalid test
Char: moxa, fix locking in moxa_write
...
Fix up trivial conflicts in drivers/bluetooth/hci_ldisc.c and
drivers/tty/serial/Makefile.
I did the hci_ldisc thing as an evil merge, cleaning things up.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
This patch adds wakeup support to the sh-sci driver. The serial
core deals with all details but defaults to wakeup disabled. So
to make use of this feature enable wakeup in sysfs:
echo enabled > /sys/class/tty/ttySC0/power/wakeup
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the Omega-PCI, an 8-port asynchronous
multiport adapter for computers with PCI bus [1].
[1] http://www.cronyx.ru/hardware/ompci.html
Signed-off-by: Antony Pavlov <antony@niisi.msk.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a break is received, Tegra's UART apparently fills the FIFO with
0 bytes. These must be drained so that they aren't interpreted as actual
data received. This allows e.g. MAGIC_SYSRQ to work on Tegra's UARTs.
v2: Added FIXME comment to clear_rx_fifo
Originally-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tegra's UART is currently auto-detected as PORT_XSCALE due to register
bit UART_IER.UUE being writable. However, the Tegra documentation states
that this register bit is reserved. Hence, we should not program it.
Instead, the documentation specifies that the UART is 16550 compatible.
However, Tegra does need register bit UART_IER.RTOIE set, which is not
enabled by any 16550 port type. This was not noticed before, since
PORT_XSCALE enables CAP_UUE, which conflates both UUE and RTOIE bit
programming.
This change defines PORT_TEGRA that doesn't set UART_CAP_UUE, but does
set UART_CAP_RTOIE, which is a new capability indicating that the RTOIE
bit needs to be enabled.
Based-on-code-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The n_tracerouter and n_tracesink line discpline drivers use the
Linux tty line discpline framework to route trace data coming
from a tty port (say UART for example) to the trace sink line
discipline driver and to another tty port(say USB). Those
these two line discipline drivers can be used together,
independently from pti.c, they are part of the original
implementation solution of the MIPI P1149.7, compact JTAG, PTI
solution for Intel mobile platforms starting with the
Medfield platform.
Signed-off-by: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to removing ARCH_S5P6442, we don't need to support
serial for S5P6442.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support to the 8250 PCI serial driver for the Digi/IBM PCIe 2-port Async EIA-232 Adapter.
Oxford Semiconductor produces a 2/4/8 port UART (OXPCIe952/OXPCIe954/OXPCIe958) chip
called the Tornado, that can be used to create a very simple serial board product.
The kernel sources currently have just 2 vendors using this chip, which is Oxford and Mainpipe.
This new Digi/IBM serial product now uses it as well.
Rather than create a long running comment of vendors using the chip, the one changed comment
in the patch below now just lists "For Oxford Semiconductor Tornado based devices" to be a
more generic comment for all vendors that end up using the Oxford Tornado chip.
Cc: Michael Reed <mreed10@us.ibm.com>
Signed-off-by: Scott Kilau <scottk@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Saves about 50KB of data.
Old/new size of all objects:
text data bss dec hex filename
563015 80096 130684 773795 bcea3 (TOTALS)
610916 32256 130632 773804 bceac (TOTALS)
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be> (for drivers/net/can/softing/softing_cs.c)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The Xilinx PS Uart is used on the new ARM based SoC. This
UART is not compatible with others such that a seperate
driver is required.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the standard mechanism to print a hex buffer
to eliminate empty printf warning.
A couple % smaller text and data too.
$ size drivers/tty/n_gsm.o*
text data bss dec hex filename
23543 312 6376 30231 7617 drivers/tty/n_gsm.o.new
24051 408 6496 30955 78eb drivers/tty/n_gsm.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The tty value that should be put is the one that was just gotten by
tty_port_tty_get, not the one that is the argument to the enclosing
function.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression struct tty_struct *x;
expression ra,rr;
statement S1,S2;
@@
x = tty_port_tty_get(...)
... when != x = rr
when any
when != tty_kref_put(x,...)
when != if (...) { ... tty_kref_put(x,...) ...}
(
if(<+...x...+>) S1 else S2
|
if(...) { ... when != x = ra
when forall
when != tty_kref_put(x,...)
*return...;
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using C line continuation inside format strings is error prone.
Clean up the unintended whitespace introduced by misuse of \.
Neaten correctly used line continations as well for consistency.
drivers/scsi/arcmsr/arcmsr_hba.c has these errors as well,
but arcmsr needs a lot more work and the driver should likely be
moved to staging instead.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
tty_write_lock and tty_write_unlock contain imbalanced locking. But
this is intentional, so mark them appropriately by
__acquires/__releases.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexander Stein