If the module parameters are invalid, we should bail out from the init
function instead of detecting it during the device probe. That way we
don't even allow the user to load the module if we don't accept the
arguments.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the gpio_mockup_ prefix to the remaining symbols that still don't
have it, so that the entire driver code is consistent.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/gpio/gpio-ath79.o
see include/linux/module.h for more information
This adds the license as "GPL v2", which matches the header of the file.
MODULE_DESCRIPTION is also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Acked-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/gpio/gpio-iop.o
see include/linux/module.h for more information
This adds the license as "GPL", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Despite commit 55020c8056 ("of: Add vendor prefix for ON Semiconductor
Corp.") was made long ago, the latter commit 9f49f6dd04 ("gpio: pca953x:
add onsemi,pca9654 id") made use of another, undocumented vendor prefix.
Since such prefix doesn't seem to be used in any device trees, I think we
can just fix the "compatible" string in the driver and the bindings and be
done with that...
Fixes: 9f49f6dd04 ("gpio: pca953x: add onsemi,pca9654 id")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As per the re-design assign the first bank regs for unbanked
irq case. This was missed out in the original patch.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixes: b5cf3fd827 ("gpio: davinci: Redesign driver to accommodate ngpios in one gpio chip")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The comment block of this file indicates GPL-2.0 "only", while the
MODULE_LICENSE is GPL-2.0 "or later", as include/linux/module.h
describes as follows:
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
I am the author of this driver, and my intention is GPL-2.0 "only".
Fixes: dbe776c2ca ("gpio: uniphier: add UniPhier GPIO controller driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 7ebc194d0f ("gpio: 74x164: Introduce 'enable-gpios'
property") added a new member gpiod_oe to the end of the struct
gen_74x164_chip, after the zero-length buffer array.
However, this buffer is a flexible array, allocated together with the
structure during .probe(). As the buffer is no longer the last member,
writing to it corrupts the newly added member after it.
During device removal, the corrupted member will be used as a pointer,
leading to a crash.
This went unnoticed, as the flexible array was declared as "buffer[0]"
instead of "buffer[]", and thus did not trigger a "flexible array member
not at end of struct" error from gcc.
Move the gpiod_oe field up to fix this, and drop the zero from the array
size to prevent future similar bugs.
Fixes: 7ebc194d0f ("gpio: 74x164: Introduce 'enable-gpios' property")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hence, series from Thierry Reding [1] merged - the OMAP GPIO driver can be
switched to reuse new feature and just fill new struct gpio_irq_chip before
calling gpiochip_add_data() instead of using few separate gpioirq chip
APIs. gpiochip_add_data() will do the job and create and initialize gpioirq
chip
[1] https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1531592.html
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Do not allow OPEN_SOURCE & OPEN_DRAIN flags in a single request. If
the hardware actually supports enabling both at the same time the
electrical result would be disastrous.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow to relax IoRestriction for certain cases.
One of the use case is incorrectly cooked ACPI table where interrupt pin is
defined with GpioIo() macro with IoRestrictionOutputOnly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some broken ACPI tables might require quirks in the OS.
Introduce quirks field in struct acpi_gpio_mapping.
Propagate them to struct acpi_gpio_info for further use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have the duplicated debug strings printed whenever
acpi_gpio_update_gpiod_flags() fails. Instead of doing this by callers,
move the debug output inside function.
In one case convert almost useless pr_debug() to dev_dbg() where
actual consumer of GPIO resource is disclosed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The further improvements are based on this change since
struct acpi_gpio_lookup is not available in some cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If error occurs, leave lookup parameter untouched.
There is no functional change, since all current callers just bail out
in case of error without using the assigned pieces.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need, since we preserve firmware settings, to override
polarity for GpioInt() resources.
While Documentation/gpio-properties.txt refers to any from GpioIo() /
GpioInt() resources, the active_low flag has been introduced to fill the
gap only for GpioIo() which lacks of that information.
Moreover, in case of GpioInt() existed solution was broken anyway, it
overrides only in one direction, i.e. from 0 to 1, otherwise it would be
still 1 as defined in the resource macro.
So, move the assignment to a right place and forbid to (semi-)override
polarity for GpioInt() type of resources.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We added acpi_gpiochip_pin_to_gpio_offset() because there was a need to
translate from ACPI GpioIo/GpioInt number to Linux GPIO number in the
Cherryview pinctrl driver. This translation is necessary because
Cherryview has gaps in the pin list and the driver used continuous GPIO
number space in Linux side as follows:
created GPIO range 0->7 ==> INT33FF:03 PIN 0->7
created GPIO range 8->19 ==> INT33FF:03 PIN 15->26
created GPIO range 20->25 ==> INT33FF:03 PIN 30->35
created GPIO range 26->33 ==> INT33FF:03 PIN 45->52
created GPIO range 34->43 ==> INT33FF:03 PIN 60->69
created GPIO range 44->54 ==> INT33FF:03 PIN 75->85
For example when ACPI GpioInt resource refers to GPIO 81 (SDMMC3_CD_B)
we translate from pin 81 to the corresponding Linux GPIO number, which
is 50. This number is then used when the GPIO is accessed through gpiolib.
It turns out, this is not necessary at all. We can just pass 1:1 mapping
between Linux GPIO numbers and pin numbers (including gaps) and the
pinctrl core handles all the details automatically:
created GPIO range 0->7 ==> INT33FF:03 PIN 0->7
created GPIO range 15->26 ==> INT33FF:03 PIN 15->26
created GPIO range 30->35 ==> INT33FF:03 PIN 30->35
created GPIO range 45->52 ==> INT33FF:03 PIN 45->52
created GPIO range 60->69 ==> INT33FF:03 PIN 60->69
created GPIO range 75->85 ==> INT33FF:03 PIN 75->85
Here GPIO 81 is exactly same than the hardware pin 81 (SDMMC3_CD_B).
As an added bonus this simplifies both the ACPI GPIO core code and the
Cherryview pinctrl driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into
a menuconfig option. This obviously has the implication of
making the subsystem menu visible in menuconfig. This is
happening because of two things:
- Intel have started to deploy and depend on pin controllers
in a way that is affecting users directly. This happens
on the highly integrated laptop chipsets named after
geographical places: baytrail, broxton, cannonlake,
cedarfork, cherryview, denverton, geminilake, lewisburg,
merrifield, sunrisepoint... It started a while back and
now it is ever more evident that this is crucial
infrastructure for x86 laptops and not an embedded
obscurity anymore. Users need to be aware.
- Pin control expanders on I2C and SPI that are
arch-agnostic. Currently Semtech SX150X and Microchip
MCP28x08 but more are expected. Users will have to be
able to configure these in directly for their set-up.
- Just go and select GPIOLIB now that we made sure that
GPIOLIB is a very vanilla subsystem. Do not depend on
it, if we need it, select it.
- Exposing the pin control subsystem in menuconfig uncovered
a bunch of obscure bugs that are now hopefully fixed,
all more or less pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and
GPIO.
- New support for clock skew/delay generic DT bindings
and generic pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying.
-----BEGIN PGP SIGNATURE-----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=kj/b
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.15 kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into a
menuconfig option. This obviously has the implication of making the
subsystem menu visible in menuconfig. This is happening because of
two things:
(a) Intel have started to deploy and depend on pin controllers in
a way that is affecting users directly. This happens on the
highly integrated laptop chipsets named after geographical
places: baytrail, broxton, cannonlake, cedarfork, cherryview,
denverton, geminilake, lewisburg, merrifield, sunrisepoint...
It started a while back and now it is ever more evident that
this is crucial infrastructure for x86 laptops and not an
embedded obscurity anymore. Users need to be aware.
(b) Pin control expanders on I2C and SPI that are arch-agnostic.
Currently Semtech SX150X and Microchip MCP28x08 but more are
expected. Users will have to be able to configure these in
directly for their set-up.
- Just go and select GPIOLIB now that we made sure that GPIOLIB is a
very vanilla subsystem. Do not depend on it, if we need it, select
it.
- Exposing the pin control subsystem in menuconfig uncovered a bunch
of obscure bugs that are now hopefully fixed, all more or less
pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and GPIO.
- New support for clock skew/delay generic DT bindings and generic
pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying"
* tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits)
pinctrl: gemini: Fix missing pad descriptions
pinctrl: Add some depends on HAS_IOMEM
pinctrl: samsung/s3c24xx: add CONFIG_OF dependency
pinctrl: gemini: Fix GMAC groups
pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support
pinctrl: ti-iodelay: remove redundant unused variable dev
pinctrl: max77620: Use common error handling code in max77620_pinconf_set()
pinctrl: gemini: Implement clock skew/delay config
pinctrl: gemini: Use generic DT parser
pinctrl: Add skew-delay pin config and bindings
pinctrl: armada-37xx: Add edge both type gpio irq support
pinctrl: uniphier: remove eMMC hardware reset pin-mux
pinctrl: rockchip: Add iomux-route switching support for rk3288
pinctrl: intel: Add Intel Cedar Fork PCH pin controller support
pinctrl: intel: Make offset to interrupt status register configurable
pinctrl: sunxi: Enforce the strict mode by default
pinctrl: sunxi: Disable strict mode for old pinctrl drivers
pinctrl: sunxi: Introduce the strict flag
pinctrl: sh-pfc: Save/restore registers for PSCI system suspend
pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description
...
Pull i2c updates from Wolfram Sang:
"This contains two bigger than usual tree-wide changes this time. They
all have proper acks, caused no merge conflicts in linux-next where
they have been for a while. They are namely:
- to-gpiod conversion of the i2c-gpio driver and its users (touching
arch/* and drivers/mfd/*)
- adding a sbs-manager based on I2C core updates to SMBus alerts
(touching drivers/power/*)
Other notable changes:
- i2c_boardinfo can now carry a dev_name to be used when the device
is created. This is because some devices in ACPI world need fixed
names to find the regulators.
- the designware driver got a long discussed overhaul of its PM
handling. img-scb and davinci got PM support, too.
- at24 driver has way better OF support. And it has a new maintainer.
Thanks Bartosz for stepping up!
The rest is regular driver updates and fixes"
* 'i2c/for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (55 commits)
ARM: sa1100: simpad: Correct I2C GPIO offsets
i2c: aspeed: Deassert reset in probe
eeprom: at24: Add OF device ID table
MAINTAINERS: new maintainer for AT24 driver
i2c: nuc900: remove platform_data, too
i2c: thunderx: Remove duplicate NULL check
i2c: taos-evm: Remove duplicate NULL check
i2c: Make i2c_unregister_device() NULL-aware
i2c: xgene-slimpro: Support v2
i2c: mpc: remove useless variable initialization
i2c: omap: Trigger bus recovery in lockup case
i2c: gpio: Add support for named gpios in DT
dt-bindings: i2c: i2c-gpio: Add support for named gpios
i2c: gpio: Local vars in probe
i2c: gpio: Augment all boardfiles to use open drain
i2c: gpio: Enforce open drain through gpiolib
gpio: Make it possible for consumers to enforce open drain
i2c: gpio: Convert to use descriptors
power: supply: sbs-message: fix some code style issues
power: supply: sbs-battery: remove unchecked return var
...
CORE:
- Fix the semantics of raw GPIO to actually be raw. No
inversion semantics as before, but also no open draining,
and allow the raw operations to affect lines used for
interrupts as the caller supposedly knows what they are
doing if they are getting the big hammer.
- Rewrote the __inner_function() notation calls to names that
make more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all
IRQs are mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This
allows us to read several GPIO lines with a single
register read. This has high value for some usecases: it
can be used to create oscilloscopes and signal analyzers
and other things that rely on reading several lines at
exactly the same instant. Also a generally nice
optimization. This uses the new assign_bit() macro from
the bitops lib that was ACKed by Andrew Morton and
is implemented for two drivers, one of them being the
generic MMIO driver so everyone using that will be able
to benefit from this.
- Do not allow requests of Open Drain and Open Source
setting of a GPIO line simultaneously. If the hardware
actually supports enabling both at the same time the
electrical result would be disastrous.
- A new interrupt chip core helper. This will be helpful
to deal with "banked" GPIOs, which means GPIO controllers
with several logical blocks of GPIO inside them. This
is several gpiochips per device in the device model, in
contrast to the case when there is a 1-to-1 relationship
between a device and a gpiochip.
NEW DRIVERS:
- Maxim MAX3191x industrial serializer, a very interesting
piece of professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the
recent Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
OTHER IMPROVEMENTS:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the
Broadcom BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal
of dead code etc.
- Explicit comments on fall-through switch() statements.
-----BEGIN PGP SIGNATURE-----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=8Mon
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.15 kernel cycle:
Core:
- Fix the semantics of raw GPIO to actually be raw. No inversion
semantics as before, but also no open draining, and allow the raw
operations to affect lines used for interrupts as the caller
supposedly knows what they are doing if they are getting the big
hammer.
- Rewrote the __inner_function() notation calls to names that make
more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all IRQs are
mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This allows us
to read several GPIO lines with a single register read. This has
high value for some usecases: it can be used to create
oscilloscopes and signal analyzers and other things that rely on
reading several lines at exactly the same instant. Also a generally
nice optimization. This uses the new assign_bit() macro from the
bitops lib that was ACKed by Andrew Morton and is implemented for
two drivers, one of them being the generic MMIO driver so everyone
using that will be able to benefit from this.
- Do not allow requests of Open Drain and Open Source setting of a
GPIO line simultaneously. If the hardware actually supports
enabling both at the same time the electrical result would be
disastrous.
- A new interrupt chip core helper. This will be helpful to deal with
"banked" GPIOs, which means GPIO controllers with several logical
blocks of GPIO inside them. This is several gpiochips per device in
the device model, in contrast to the case when there is a 1-to-1
relationship between a device and a gpiochip.
New drivers:
- Maxim MAX3191x industrial serializer, a very interesting piece of
professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the recent
Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
Other improvements:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the Broadcom
BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal of dead
code etc.
- Explicit comments on fall-through switch() statements"
* tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (65 commits)
gpio: tegra186: Remove tegra186_gpio_lock_class
gpio: rcar: Add r8a77995 (R-Car D3) support
pinctrl: bcm2835: Fix some merge fallout
gpio: Fix undefined lock_dep_class
gpio: Automatically add lockdep keys
gpio: Introduce struct gpio_irq_chip.first
gpio: Disambiguate struct gpio_irq_chip.nested
gpio: Add Tegra186 support
gpio: Export gpiochip_irq_{map,unmap}()
gpio: Implement tighter IRQ chip integration
gpio: Move lock_key into struct gpio_irq_chip
gpio: Move irq_valid_mask into struct gpio_irq_chip
gpio: Move irq_nested into struct gpio_irq_chip
gpio: Move irq_chained_parent to struct gpio_irq_chip
gpio: Move irq_default_type to struct gpio_irq_chip
gpio: Move irq_handler to struct gpio_irq_chip
gpio: Move irqdomain into struct gpio_irq_chip
gpio: Move irqchip into struct gpio_irq_chip
gpio: Introduce struct gpio_irq_chip
pinctrl: armada-37xx: remove unused variable
...
Pull irq core updates from Thomas Gleixner:
"A rather large update for the interrupt core code and the irq chip drivers:
- Add a new bitmap matrix allocator and supporting changes, which is
used to replace the x86 vector allocator which comes with separate
pull request. This allows to replace the convoluted nested loop
allocation function in x86 with a facility which supports the
recently added property of managed interrupts proper and allows to
switch to a best effort vector reservation scheme, which addresses
problems with vector exhaustion.
- A large update to the ARM GIC-V3-ITS driver adding support for
range selectors.
- New interrupt controllers:
- Meson and Meson8 GPIO
- BCM7271 L2
- Socionext EXIU
If you expected that this will stop at some point, I have to
disappoint you. There are new ones posted already. Sigh!
- STM32 interrupt controller support for new platforms.
- A pile of fixes, cleanups and updates to the MIPS GIC driver
- The usual small fixes, cleanups and updates all over the place.
Most visible one is to move the irq chip drivers Kconfig switches
into a separate Kconfig menu"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
genirq: Fix type of shifting literal 1 in __setup_irq()
irqdomain: Drop pointless NULL check in virq_debug_show_one
genirq/proc: Return proper error code when irq_set_affinity() fails
irq/work: Use llist_for_each_entry_safe
irqchip: mips-gic: Print warning if inherited GIC base is used
irqchip/mips-gic: Add pr_fmt and reword pr_* messages
irqchip/stm32: Move the wakeup on interrupt mask
irqchip/stm32: Fix initial values
irqchip/stm32: Add stm32h7 support
dt-bindings/interrupt-controllers: Add compatible string for stm32h7
irqchip/stm32: Add multi-bank management
irqchip/stm32: Select GENERIC_IRQ_CHIP
irqchip/exiu: Add support for Socionext Synquacer EXIU controller
dt-bindings: Add description of Socionext EXIU interrupt controller
irqchip/gic-v3-its: Fix VPE activate callback return value
irqchip: mips-gic: Make IPI bitmaps static
irqchip: mips-gic: Share register writes in gic_set_type()
irqchip: mips-gic: Remove gic_vpes variable
irqchip: mips-gic: Use num_possible_cpus() to reserve IPIs
irqchip: mips-gic: Configure EIC when CPUs come online
...
This is no longer required after commit 959bc7b22b
("gpio: Automatically add lockdep keys")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to avoid lockdep boilerplate in individual drivers, turn the
gpiochip_add_data() function into a macro that creates a unique class
key for each driver.
Note that this has the slight disadvantage of adding a key for each
driver registered with the system. However, these keys are 8 bytes in
size, which is negligible and a small price to pay for generic
infrastructure.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
[renane __gpiochip_add_data() to gpiochip_add_data_with_key]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO chips cannot support sparse IRQ numbering and therefore need
to manually allocate their interrupt descriptors statically. For these
cases, a driver can pass the first allocated IRQ via the struct
gpio_irq_chip's "first" field and thereby cause the IRQ domain to map
all IRQs during initialization.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The nested field in struct gpio_irq_chip currently has two meanings. On
one hand it marks an IRQ chip as being nested (as opposed to chained),
while on the other hand it also means that an IRQ chip uses nested
thread handlers.
However, nested IRQ chips can already be identified by the fact that
they don't pass a parent handler (the driver would instead already have
installed a nested handler using request_irq()).
Therefore, the only use for the nested attribute is to inform gpiolib
that an IRQ chip uses nested thread handlers (as opposed to regular,
non-threaded handlers). To clarify its purpose, rename the field to
"threaded".
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra186 has two GPIO controllers that are largely register compatible
between one another but are completely different from the controller
found on earlier generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Export these functions so that drivers can explicitly use these when
setting up their IRQ domain.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently GPIO drivers are required to add the GPIO chip and its
corresponding IRQ chip separately, which can result in a lot of
boilerplate. Use the newly introduced struct gpio_irq_chip, embedded in
struct gpio_chip, that drivers can fill in if they want the GPIO core
to automatically register the IRQ chip associated with a GPIO chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fd9c963c56 ("gpio: mb86s70: Return error if requesting an
already assigned gpio") adds code that infers from the state of the
GPIO Pin Function Register (PFR) whether a GPIO has been assigned
already. This assumes that the pin functions are set to 'peripheral'
when the driver is loaded, which is not guaranteed. Also, the GPIO
layer is perfectly capable of keeping track of which GPIOs have been
assigned already, so we shouldn't need this check in the first place.
This reverts commit fd9c963c56.
Cc: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to reuse this driver for the Socionext Synquacer SC2A11 SoC,
which inherited this IP from Fujitsu, remove the ARCH_MB86S7X Kconfig
dependency, and revert the changes that prevent it from being built as
a module.
This reverts commits d65aa4b67b and
d5610e514e.
Cc: Geliang Tang <geliangtang@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[Folded in module_platform_driver() fixup]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit corrects problems with the previous wake implementation
by implementing suspend and resume power management operations and
the driver shutdown operation.
Wake masks are used to keep track of which GPIO should wake the
device. On suspend the GPIO state is saved and the possible wakeup
sources are explicitly unmasked in the hardware. Non-wakeup sources
are explicitly masked so IRQCHIP_MASK_ON_SUSPEND is no longer
necessary. The saved state of the GPIO is restored upon resume.
It is important not to write to the GPIO status register since this
has the effect of clearing bits. The status register is explicitly
removed from the register save and restore to ensure this.
The shutdown operation allows the hardware to be put into the same
quiesced state as the suspend operation and removes the need for
the reboot notifier.
Unfortunately, there appears to be some confusion about whether
a pending disabled wake interrupt should wake the system. If a wake
capable interrupt is disabled using the default "lazy disable"
behavior and it is triggered before the suspend_device_irq call
the interrupt hardware will be acknowledged by mask_ack_irq and the
IRQS_PENDING flag is added to its state. However, the IRQS_PENDING
flag of wake interrupts is not checked to prevent the transition to
suspend and the hardware has been acked which prevents its wakeup.
If the lazy disabled interrupt is triggered after the call to
suspend_device_irqs then the wakeup logic will abort the suspend.
The irq_disable method is defined by this GPIO driver to prevent
lazy disable so that the pending hardware state remains asserted
allowing the hardware to wake and providing a consistent behavior.
In addition, the IRQ_DISABLE_UNLAZY flag is set for the non-wake
parent interrupt as a convenience to prevent the need to add code
to the brcmstb_gpio_irq_handler to support "lazy disable" of the
non-wake parent interrupt when it is disabled during suspend and
resume. Chained interrupt parents are not normally disabled, but
these GPIO devices have different parent interrupts for wake and
non-wake handling. It is convenient to mask the non-wake parent
when suspending to preserve the hardware state for proper wakeup
accounting when the driver is resumed.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOLIB IRQ chip helpers were very appealing, but badly broke
the 1:1 mapping between a GPIO controller's device_node and its
interrupt domain.
When another device-tree node references a GPIO device as its
interrupt parent, the irq_create_of_mapping() function looks for
the irq domain of the GPIO device and since all bank irq domains
reference the same GPIO device node it always resolves to the irq
domain of the first bank regardless of which bank the number of
the GPIO should resolve. This domain can only map hwirq numbers
0-31 so interrupts on GPIO above that can't be mapped by the
device-tree.
This commit effectively reverts the patch from Gregory Fong [1]
that was accepted upstream and replaces it with a consolidated
irq domain implementation with one larger interrupt domain per
GPIO controller instance spanning multiple GPIO banks based on
an earlier patch [2] also submitted by Gregory Fong.
[1] https://patchwork.kernel.org/patch/6921561/
[2] https://patchwork.kernel.org/patch/6347811/
Fixes: 19a7b6940b ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit corrects a bug when configuring the GPIO hardware for
IRQ_TYPE_LEVEL_LOW and IRQ_TYPE_LEVEL_HIGH interrupt types. The
hardware is now correctly configured to support those types.
Fixes: 19a7b6940b ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reading and writing the gpio bank status register each time a pending
interrupt bit is serviced could cause new pending bits to be cleared
without servicing the associated interrupts.
By using the handle_level_irq flow instead of the handle_simple_irq
flow we get proper handling of interrupt masking as well as acking
of interrupts. The irq_ack method is added to support this.
Fixes: 19a7b6940b ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The basic memory-mapped GPIO controller lock must be released
before calling the registered GPIO interrupt handlers to allow
the interrupt handlers to access the hardware.
Examples of why a GPIO interrupt handler might want to access
the GPIO hardware include an interrupt that is configured to
trigger on rising and falling edges that needs to read the
current level of the input to know how to respond, or an
interrupt that causes a change in a GPIO output in the same
bank. If the lock is not released before enterring the handler
the hardware accesses will deadlock when they attempt to grab
the lock.
Since the lock is only needed to protect the calculation of
unmasked pending interrupts create a dedicated function to
perform this and hide the complexity.
Fixes: 19a7b6940b ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit allows a wakeup parent interrupt to be shared between
instances.
It also removes the redundant can_wake member of the private data
structure by using whether the parent_wake_irq has been defined to
indicate that the GPIO device can wake.
Fixes: 19a7b6940b ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a jump target so that a bit of exception handling can be better reused
at the end of this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using devm_ioremap_resource() has several advantages over devm_ioremap():
- it checks the passed resource's validity;
- it calls devm_request_mem_region() to check for the resource overlap;
- it prints an error message in case of error.
We can call devm_ioremap_resource() instead of devm_ioremap_nocache()
as ioremap() and ioremap_nocache() are implemented identically on ARM.
Doing this saves 2 LoCs and 80 bytes (AArch64 gcc 4.8.5).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some busses, like I2C, strictly need to have the line handled
as open drain, i.e. not actively driven high. For this reason
the i2c-gpio.c bit-banged I2C driver is reimplementing open
drain handling outside of gpiolib.
This is not very optimal. Instead make it possible for a
consumer to explcitly express that the line must be handled
as open drain instead of allowing local hacks papering over
this issue.
The descriptor tables, whether DT, ACPI or board files, should
of course have flagged these lines as open drain. E.g.:
enum gpio_lookup_flags GPIO_OPEN_DRAIN for a board file, or
gpios = <&foo 42 GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN>; in a
device tree using <dt-bindings/gpio/gpio.h>
But more often than not, these descriptors are wrong. So
we need to make it possible for consumers to enforce this
open drain behaviour.
We now have two new enumerated GPIO descriptor config flags:
GPIOD_OUT_LOW_OPEN_DRAIN and GPIOD_OUT_HIGH_OPEN_DRAIN
that will set up the lined enforced as open drain as output
low or high, using open drain (if the driver supports it)
or using open drain emulation (setting the line as input
to drive it high) from the gpiolib core.
Cc: linux-gpio@vger.kernel.org
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is possible to read all lines of a generic MMIO GPIO chip
with a single register read so support this if we are in
native endianness.
Add an especially quirky callback to read multiple lines for
the variants that require you to read values from the
output registers if and only if the line is set as output.
We managed to do that with a maximum of two register reads,
and just one read if the requested lines are all input or all
output.
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The vtable call pin2mask() was introducing a vtable function call
in every gpiochip callback for a generic MMIO GPIO chip. This was
not exactly efficient. (Maybe link-time optimization could get rid of
it, I don't know.)
After removing all external calls into this API we can make it a
boolean flag in the struct gpio_chip call and sink the function into
the gpio-mmio driver yielding encapsulation and potential speedups.
Cc: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MPC8xxx driver is always instantiating its generic GPIO functions
with the flag BGPIOF_BIG_ENDIAN. This means "big-endian bit order"
and means the bits representing the GPIO lines in the registers are
reversed around 31 bits so line 0 is at bit 31 and so forth down to
line 31 in bit 0.
Instead of looping into the generic MMIO gpio to do the simple
calculation of a bitmask, through a vtable call with two parameters
likely using stack frames etc (unless the compiler optimize it)
and obscuring the view for the programmer, let's just open-code
what the call does. This likely executes faster, saves space and
makes the code easier to read.
Cc: Liu Gang <Gang.Liu@nxp.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin2mask() accessor only shuffles BIT ORDER in big endian systems,
i.e. the bitstuffing is swizzled big endian so "bit 0" is bit 7 or
bit 15 or bit 31 or so.
The brcmstb only uses big endian BYTE ORDER which will be taken car of
by the ->write_reg() callback.
Just use BIT(offset) to assign the bit.
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin2mask() accessor only shuffles BIT ORDER in big endian systems,
i.e. the bitstuffing is swizzled big endian so "bit 0" is bit 7 or
bit 15 or bit 31 or so.
The grgpio only uses big endian BYTE ORDER which will be taken car of
by the ->write_reg() callback.
Just use BIT(offset) to assign the bit.
Acked-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When no flags are given, the native endianness is used to access
the MMIO registers, and the pin2mask() call can simply be
converted to a BIT() call, as per the default pin2mask()
implementation in gpio-mmio.c.
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DW APB GPIO driver uses the generic GPIO library gpio-mmio,
and initialize the flags as "false", which should be 0.
When no flags are given, the native endianness is used to access
the MMIO registers, and the pin2mask() call can simply be
converted to a BIT() call, as per the default pin2mask()
implementation in gpio-mmio.c.
Acked-by: Alan Tull <atull@kernel.org>
Acked-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This GPIO controller is used on UniPhier SoC family.
It also serves as an interrupt controller, but interrupt signals are
just delivered to the parent irqchip without any latching or OR'ing.
This type of hardware can be well described with hierarchy IRQ domain.
One unfortunate thing for this device is that the interrupt mapping to
the interrupt parent is not contiguous.
I asked how DT can describe interrupt mapping between two irqchips [1],
but I could not find a good solution (at least in the framework level).
In fact, irqchip drivers using hierarchy domain generally hard-code the
DT binding of their parent.
After tackling on several approaches such as hard-code of hwirqs,
irq_domain_push_irq(), I ended up with a vendor specific property.
If we come up with a good idea to support this in the framework, we
can migrate over to it, but we can live with a driver-level solution
for now.
[1] https://lkml.org/lkml/2017/7/6/758
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Literally.
I expect "lose" was meant here, rather than "loose", though you could feasibly
use a somewhat uncommon definition of "loose" to mean what would be meant by
"lose": "Loose the hounds" for instance, as in "Release the hounds".
Substituting in "value" for "hounds" gives "release the value", and makes some
sense, but futher substituting back to loose gives "loose the value" which
overall just seems a bit anachronistic.
Instead, use modern, pragmatic English and save a character.
Cc: Russell Currey <ruscur@russell.cc>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver was developed for and tested with the MAX31913 built into
the Revolution Pi by KUNBUS, but should work with all members of the
MAX3191x family:
MAX31910: low power
MAX31911: LED drivers
MAX31912: LED drivers + 2nd voltage monitor + low power
MAX31913: LED drivers + 2nd voltage monitor
MAX31953: LED drivers + 2nd voltage monitor + isolation
MAX31963: LED drivers + 2nd voltage monitor + isolation + buck regulator
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the two separate calls for clearing the irqchip's chained handler
and its data with a single irq_set_chained_handler_and_data() call.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
OPEN_DRAIN and OPEN_SOURCE flags only affect the way we drive a GPIO
line, so they only make sense for output mode. Just as we only allow
input mode for event handle requests, don't allow passing open-drain
and open-source flags for any other mode than explicit output.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There's no need to check the validity of handle request flags more
than once, right after copying the data from user. Move the check
out of the for loop and simplify the error path by bailing out before
allocating any resources.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SPI-attached GPIO controllers typically read out all inputs in one go.
If callers desire the values of multipe inputs, ideally a single readout
should take place to return the desired values. However the current
driver API only offers a ->get callback but no ->get_multiple (unlike
->set_multiple, which is present). Thus, to read multiple inputs, a
full readout needs to be performed for every single value (barring
driver-internal caching), which is inefficient.
In fact, the lack of a ->get_multiple callback has been bemoaned
repeatedly by the gpio subsystem maintainer:
http://www.spinics.net/lists/linux-gpio/msg10571.htmlhttp://www.spinics.net/lists/devicetree/msg121734.html
Introduce the missing callback. Add corresponding consumer functions
such as gpiod_get_array_value(). Amend linehandle_ioctl() to take
advantage of the newly added infrastructure. Update the documentation.
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some platforms require reset to be released to allow register
access.
Signed-off-by: Alan Tull <atull@kernel.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
[Added DT bindings oneliner for standard reset binding]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SX150X driver was moved over to pin control a while back.
The GPIO Kconfig symbol creates a circular dependency since
it requires GPIOLIB and the pin control driver selects GPIOLIB
so get rid of the old annoying Kconfig option.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the of_device_get_match_data() helper instead of open coding.
Note that the gpio-rcar driver is used with DT only, so there's always a
valid match.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now acking of edge irqs happens the following way:
- omap_gpio_irq_handler
- "isr" = read irq status
- omap_clear_gpio_irqbank(bank, isr_saved & ~level_mask);
^ clear edge status, so irq can be accepted
- loop while "isr"
generic_handle_irq()
- handle_edge_irq()
- desc->irq_data.chip->irq_ack(&desc->irq_data);
- omap_gpio_ack_irq()
it might be that at this moment edge IRQ was triggered again and it will be
cleared and IRQ will be lost.
Use handle_simple_irq and clear edge interrupts early without disabling them in
omap_gpio_irq_handler to avoid loosing interrupts.
[1] https://marc.info/?l=linux-omap&m=149004465313534&w=2
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These request/free functions are just reimplementations of the
standard helpers in gpiolib. Delete them and replace with the
helpers.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently calls to:
gpiod_direction_output_raw()
gpiod_set_raw_value()
gpiod_set_raw_array_value()
gpiod_set_raw_value_cansleep()
gpiod_set_raw_array_value_cansleep()
Respect that we do not want to invert the value written, but will
still apply special open drain/open source semantics if the line has
an open drain/open source flag.
It also forbids us from driving an output marked as an interrupt
line.
This does not fit with the function name and expected semantics. In
the w1 host driver (for example) we need to handle a line as open drain
but sometimes force it to pull up, which means we should be able to
use the gpiod_set_raw_value() for this, but it currently does not
work.
There are also use cases where users actually want to drive a line
used by an interrupt. This is what they should be expected to use
the *raw* accessors for.
I have looked over the current users of this API and they do not seem
to be using the *raw* accessors with open drain or open source so let's
augment this behaviour before we have users expecting the inconsistent
semantic.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The arbitrarily marking of a function with _ or __ is taking to mean
"perform some inner core of the caller" or something like that. At other
times, this syntax has a totally different meaning.
I don't like this since it is unambious and unhelpful to people reading
the code, so replace it with _commit() suffixes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq_domain_ops.activate() callback has no return value and no way to
tell the function that the activation is early.
The upcoming changes to support a reservation scheme which allows to assign
interrupt vectors on x86 only when the interrupt is actually requested
requires:
- A return value, so activation can fail at request_irq() time
- Information that the activate invocation is early, i.e. before
request_irq().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.848490816@linutronix.de
This driver implements .alloc() hook, so .map() is not used.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: David Daney <david.daney@cavium.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl_request_gpio() and pinctrl_free_gpio() break the nice
namespacing in the other cross-calls like pinctrl_gpio_foo().
Just rename them and all references so we have one namespace
with all cross-calls under pinctrl_gpio_*().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_kasprintf() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_kasprintf() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The probe function calls omap_gpio_show_rev(), which on most
compilers is inlined, but on the old gcc-4.6 is not, causing
a valid warning about the incorrect __init annotation:
WARNING: vmlinux.o(.text+0x40f614): Section mismatch in reference from the function omap_gpio_probe() to the function .init.text:omap_gpio_show_rev()
The function omap_gpio_probe() references
the function __init omap_gpio_show_rev().
This is often because omap_gpio_probe lacks a __init
annotation or the annotation of omap_gpio_show_rev is wrong.
This removes the __init.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch supports irq_set_wake for dwapb gpio. It allows GPIOs
to be configured as wakeup sources and wake the system from suspend.
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since f94277af03 ("of/platform: Initialise dev->fwnode appropriately"),
of_platform_device_create() already initialises dev->fwnode to that of
the appropriate device_node, so within the driver we shouldn't need to
care whether we probed via DT or ACPI.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gcc-7 notices that the pin_table is an array of 16-bit numbers,
but fails to take the following range check into account:
drivers/gpio/gpiolib-acpi.c: In function 'acpi_gpiochip_request_interrupt':
drivers/gpio/gpiolib-acpi.c:206:24: warning: '%02X' directive writing between 2 and 4 bytes into a region of size 3 [-Wformat-overflow=]
sprintf(ev_name, "_%c%02X",
^~~~
drivers/gpio/gpiolib-acpi.c:206:20: note: directive argument in the range [0, 65535]
sprintf(ev_name, "_%c%02X",
^~~~~~~~~
drivers/gpio/gpiolib-acpi.c:206:3: note: 'sprintf' output between 5 and 7 bytes into a destination of size 5
sprintf(ev_name, "_%c%02X",
^~~~~~~~~~~~~~~~~~~~~~~~~~~
agpio->triggering == ACPI_EDGE_SENSITIVE ? 'E' : 'L',
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
pin);
~~~~
As suggested by Andy, this changes the format string to have a fixed length.
Since modifying the range check did not help, I also opened a bug against
gcc, see link below.
Fixes: 0d1c28a449 ("gpiolib-acpi: Add ACPI5 event model support to gpio.")
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patchwork.kernel.org/patch/9840801/
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82123
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
IRQ_DOMAIN_HIERARCHY is not user-configurable, but supposed to be
selected by drivers that need IRQ domain hierarchy support.
GPIO_THUNDERX is the only user of "depends on IRQ_DOMAIN_HIERARCHY".
This means, we can not enable GPIO_THUNDERX unless other drivers
select IRQ_DOMAIN_HIERARCHY elsewhere. This is odd. Flip the logic.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
- New Device Support
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
- New Functionality
- Amend API to provide register layout; atmel-smc
- Fix-ups
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
- Bug Fixes
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll
-----BEGIN PGP SIGNATURE-----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=TKIm
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
Core changes
- Allow the GPIO irqchip to allocate IRQs dynamically. This is
an important change on systems where only a restricted number
of IRQs, lesser than the number of GPIO lines, can be utilized.
Now we can allocate these on a first-come-first-served basis
instead of hogging up valuable IRQ lines.
- Serious fix-up of the kerneldoc documentation and inclusion
into the kerneldoc builds.
- Pulled in the IRQ simulator from the IRQ core tree and use
this in the GPIO mockup driver for exhaustive testing of
interrupt abilities.
New drivers
- New driver for ThunderX and OCTEON-TX. This is especially
interesting as it picks up improvements from the IRQ core that
allow us to handle fasteoi ACKs upwards in a hierarchy when
there are IRQ flag latches on several levels in a hierarchy.
Very interesting work here.
- New subdriver for Renesas R-Car r8a7745 (RZ/G1E).
Misc
- Several fixes and improvements for Xilinx Zynq GPIO.
- Support an enablement GPIO for the 74x164 GPIO.
- Switch a bunch of chips to use devres to allocate irq
descriptors.
- A bunch of constification fixes.
-----BEGIN PGP SIGNATURE-----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=TYNw
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of the GPIO changes for the v4.14 cycle.
Not so much changes this time, phew. David Daney and Bartosz
Golaszewski did all the really interesting work in infrastructure
improvement across GPIO and IRQ core, hats off for them and to tglx
and Marc Z for general help with these patch sets.
Core changes:
- Allow the GPIO irqchip to allocate IRQs dynamically. This is an
important change on systems where only a restricted number of IRQs,
lesser than the number of GPIO lines, can be utilized. Now we can
allocate these on a first-come-first-served basis instead of
hogging up valuable IRQ lines.
- Serious fix-up of the kerneldoc documentation and inclusion into
the kerneldoc builds.
- Pulled in the IRQ simulator from the IRQ core tree and use this in
the GPIO mockup driver for exhaustive testing of interrupt
abilities.
New drivers:
- New driver for ThunderX and OCTEON-TX. This is especially
interesting as it picks up improvements from the IRQ core that
allow us to handle fasteoi ACKs upwards in a hierarchy when there
are IRQ flag latches on several levels in a hierarchy. Very
interesting work here.
- New subdriver for Renesas R-Car r8a7745 (RZ/G1E).
Misc:
- Several fixes and improvements for Xilinx Zynq GPIO.
- Support an enablement GPIO for the 74x164 GPIO.
- Switch a bunch of chips to use devres to allocate irq descriptors.
- A bunch of constification fixes"
* tag 'gpio-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (63 commits)
gpio: mockup: remove unused variable gc
gpio: pl061: constify amba_id
Revert "gpiolib: request the gpio before querying its direction"
gpio: twl6040: remove unneeded forward declaration
gpio: zevio: make gpio_chip const
gpio: add gpio_add_lookup_tables() to add several tables at once
gpio: rcar: Add r8a7745 (RZ/G1E) support
gpio: brcmstb: check return value of gpiochip_irqchip_add()
MAINTAINERS: Add entry for THUNDERX GPIO Driver.
gpio: Add gpio driver support for ThunderX and OCTEON-TX
gpio: mockup: use irq_sim
gpio: mxs: use devres for irq generic chip
gpio: mxc: use devres for irq generic chip
gpio: pch: use devres for irq generic chip
gpio: ml-ioh: use devres for irq generic chip
gpio: sta2x11: use devres for irq generic chip
gpio: sta2x11: disallow unbinding the driver
gpio: mxs: disallow unbinding the driver
gpio: mxc: disallow unbinding the driver
gpio: aspeed: Remove reference to clock name in debounce warning message
...
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The variable gc is assigned but never read and is redundant. Remove it.
Cleans up clang warning:
drivers/gpio/gpio-mockup.c:169:2: warning: Value stored to 'gc' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 108d23e322.
It turns out this causes a regression on the OMAP, Marvell
and Renesas.
Reported-by: Tony Lindgren <tony@atomide.com>
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reported-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no reference to twl6040gpo_chip before its definition.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make this const as it is only used as a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When converting legacy board to use gpiod API() there might be several
lookup tables in board file, let's provide a way to register them all at
once.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Because gpiochip_irqchip_add() may fail, its return value should
be checked.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cavium ThunderX and OCTEON-TX are arm64 based SoCs. Add driver for
the on-chip GPIO pins.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Shrink the driver by removing the code dealing with dummy interrupts
and replacing it with calls to the irq_sim API.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is non-modular so explicitly disallow a driver unbind.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is non-modular so explicitly disallow a driver unbind.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is non-modular so explicitly disallow a driver unbind.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
HPLL is in fact not the clock we need. Remove the description of which clock we
failed to find a phandle to in order to avoid any further error.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
74HC595 has an /OE (output enable) pin that can be controlled by a GPIO.
Introduce an optional property called 'enable-gpios' that allows
controlling the /OE pin.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make the structure const as it is only passed to the function
devm_regmap_add_irq_chip having the corresponding argument as const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix function parameters alignment reported by checkpatch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes the below warning
-->Block comments should align the * on each line.
-->suspect code indent for conditional statements.
-->Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove one additional line and add two new. All are reported by checkpatch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes the kernel doc warnings in the driver.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch provides workaround in the gpio driver
for Zynq and ZynqMP Platforms by reading pin value
of EMIO banks through DATA register as it was unable
to read the value of it from DATA_RO register.
Signed-off-by: Swapna Manupati <swapnam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for suspend resume. Now that we can lose context across
a suspend/ resume cycle. Add support for the context restore.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for TPS68470 GPIOs.
There are 7 GPIOs and a few sensor related GPIOs.
These GPIOs can be requested and configured as
appropriate.
The GPIOs are also provided with descriptive names.
However, the typical use case is that the OS GPIO
driver will interact with TPS68470 GPIO driver
to configure these GPIOs, as requested by the
platform firmware.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently davinci_gpio_irq_setup return value is ignored. Handle the
return value appropriately.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Rapid General-Purpose Input and Output with 2 Ports (RGPIO2P)
on MX7ULP is similar to GPIO on Vibrid. But unlike Vibrid, the
RGPIO2P has an extra Port Data Direction Register (PDDR) used
to configure the individual port pins for input or output.
We introduce a bool have_paddr with fsl_gpio_soc_data data
to distinguish this differences. And we support getting the output
status by checking the GPIO direction in PDDR.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_get_irq() returns an error code, but the gpio-msic driver
ignores it and always returns -EINVAL. This is not correct, and
prevents -EPROBE_DEFER from being propagated properly.
Notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print and propagate the return value of platform_get_irq on failure.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
omap_gpio_probe() can fail here and we must disable clock.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
From the datasheet, the GPIO interface is identical to IT8728 (same
description), so just add it to the same case as the other chip.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In most of the cases, integers in this file can't be negative, so the
type can be more restricted for clarity.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix a couple of checkpatch warnings, such as complaints about bare
unsigned being used (instead of unsigned int) and missing blank lines
after declarations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rather than manually compute the size of an array, pass the number and
element size to kcalloc().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_device_get_match_data() can never return NULL, therefore the check
for NULL values is unnecessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix up some references to parameters to match the code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix up a parameter description to match the code and fix markup for a
constant to prettify output.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add missing descriptions for some parameters to match the code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add descriptions for missing fields and fix up some parameter references
to match the code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some kerneldoc has become stale or wasn't quite correct from the outset.
Fix up the most serious issues to silence warnings when building the
documentation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of using platform_get_resource() and getting the interrupts from
the resource, use platform_get_irq() which is slightly easier to use and
covers some special cases that the former doesn't.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use platform_irq_count() instead of open-coding the same code sequence.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Tien Hock Loh <thloh@altera.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case of devm_clk_get failure use dev_err instead of printk
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the devm version of gpiochip_add_data and pass on the
return value. This avoids memory leak due to gpiochip_add_data
in case the driver is unbound.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into another structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
1954 600 0 2554 9fa drivers/gpio/gpio-altera-a10sr.o
after:
text data bss dec hex filename
1655 512 0 2167 877 drivers/gpio/gpio-altera-a10sr.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Errors from enable_irq_wake() in gpio_set_wake_irq() were silently ignored.
Thus led to the problem that gpio_set_wake_irq() always returned
successfully, even if enable_irq_wake() returned an error.
Signed-off-by: Philipp Rosenberger <p.rosenberger@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add fallback compatibility string for R-Car Gen 1, 2 and 3.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, f.e. Gen 1 and 2. But beyond that its not clear what the relationship
between IP blocks might be. For example, I believe that r8a7790 is older
than r8a7791 but that doesn't imply that the latter is a descendant of the
former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme being adopted for
drivers for Renesas SoCs.
Also deprecate renesas,gpio-rcar as its name is more generic than its
implementation.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio_to_irq() API expected to be used by GPIO consumers and
not drivers and there are no guarantee that its gpiolib implementation
is irq safe.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio_to_irq() API expected to be used by GPIO consumers and
not drivers and there are no guarantee that its gpiolib implementation
is irq safe.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now IRQ mappings are always created for all (allowed) GPIOs in gpiochip in
gpiochip_irqchip_add_key() which goes against the idea of SPARSE_IRQ and,
as result, leads to:
- increasing of memory consumption for IRQ descriptors most of which will
never ever be used (espessially on platform with a high number of GPIOs).
(sizeof(struct irq_desc) == 256 on my tested platforms)
- imposibility to use GPIO irqchip APIs by gpio drivers when HW implements
GPIO IRQ functionality as IRQ crossbar/router which has only limited
number of IRQ outputs (example from [1], all GPIOs can be mapped on only 8
IRQs).
Hence, remove static IRQ mapping code from gpiochip_irqchip_add_key() and
instead replace irq_find_mapping() with irq_create_mapping() in
gpiochip_to_irq(). Also add additional gpiochip_irqchip_irq_valid() calls
in gpiochip_to_irq() and gpiochip_irq_map().
After this change gpio2irq mapping will happen the following way when GPIO
irqchip APIs are used by gpio driver:
- IRQ mappings will be created statically if driver passes first_irq>0
vlaue in gpiochip_irqchip_add_key().
- IRQ mappings will be created dynamically from gpio_to_irq() or
of_irq_get().
Tested on am335x-evm and dra72-evm-revc.
- dra72-evm-revc: number of created irq mappings decreased from 402 -> 135
Mem savings 267*256 = 68352 (66kB)
- am335x-evm: number of created irq mappings decreased from 188 -> 63
Mem savings 125*256 = 32000 (31kB)
[1] https://lkml.org/lkml/2017/6/15/428
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Before querying a GPIO to determine its direction, the GPIO should be
formally requested. This allows the GPIO driver to block access to
unavailable GPIOs, which makes it easier for some drivers to support
sparse GPIO maps.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
i2c_smbus commands handle the correct byte order for smbus transactions
internally. This will currently result in incorrect operation on big
endian systems.
Suggested-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When switching to regmap, the way to compute the irq cause was
reorganized. However while doing it, a typo was introduced: a 'xor'
replaced a 'and'.
This lead to wrong behavior in the interrupt handler ans one of the
symptom was wrong irq handler called on the Armada 388 GP:
"->handle_irq(): c016303c,
handle_bad_irq+0x0/0x278
->irq_data.chip(): c0b0ec0c,
0xc0b0ec0c
->action(): (null)
IRQ_NOPROBE set
IRQ_NOREQUEST set
unexpected IRQ trap at vector 00
irq 0, desc: ee804800, depth: 1, count: 0, unhandled: 0"
Fixes: 2233bf7a92 ("gpio: mvebu: switch to regmap for register access")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Check user-given gpio number and reject it before
calling gpio_to_desc() because gpio_to_desc() is
for kernel driver and it expects given gpio number
is valid (means 0 to 511).
If given number is invalid, gpio_to_desc() calls
WARN() and dump registers and stack for debug.
This means user can easily kick WARN() just by
writing invalid gpio number (e.g. 512) to
/sys/class/gpio/export.
Fixes: 0e9a5edf5d ("gpio: fix deferred probe detection for legacy API")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When more than one GPIO IRQs are triggered simultaneously,
tegra_gpio_irq_handler() called chained_irq_exit() multiple
times for one chained_irq_enter().
Fixes: 3c92db9ac0
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
[Also changed the variable to a bool]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The previous fix for filtering out of unwatched events was not entirely
correct. Instead of skipping the events we don't want, they are now
interpreted as events with opposing edge.
In order to fix it: always read the GPIO line value on interrupt and
only emit the event if it corresponds with the event type we requested.
Cc: stable@vger.kernel.org
Fixes: ad537b8225 ("gpiolib: fix filtering out unwanted events")
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The device-specific property should be prefixed with the vendor name,
not "linux,", as Linus Walleij pointed out. Change this and document the
bindings of this platform device.
We didn't ship the old binding in a release yet. So we can still change
it without breaking an official API.
Fixes: 380b1e2f3a ("gpio-exar/8250-exar: Make set of exported GPIOs configurable")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Bartosz Golaszewski