Including:
- Allow to compile the ARM-SMMU drivers as modules.
- Fixes and cleanups for the ARM-SMMU drivers and io-pgtable code
collected by Will Deacon. The merge-commit (6855d1ba75) has all the
details.
- Cleanup of the iommu_put_resv_regions() call-backs in various drivers.
- AMD IOMMU driver cleanups.
- Update for the x2APIC support in the AMD IOMMU driver.
- Preparation patches for Intel VT-d nested mode support.
- RMRR and identity domain handling fixes for the Intel VT-d driver.
- More small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----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=HMIT
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Allow compiling the ARM-SMMU drivers as modules.
- Fixes and cleanups for the ARM-SMMU drivers and io-pgtable code
collected by Will Deacon. The merge-commit (6855d1ba75) has all the
details.
- Cleanup of the iommu_put_resv_regions() call-backs in various
drivers.
- AMD IOMMU driver cleanups.
- Update for the x2APIC support in the AMD IOMMU driver.
- Preparation patches for Intel VT-d nested mode support.
- RMRR and identity domain handling fixes for the Intel VT-d driver.
- More small fixes and cleanups.
* tag 'iommu-updates-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (87 commits)
iommu/amd: Remove the unnecessary assignment
iommu/vt-d: Remove unnecessary WARN_ON_ONCE()
iommu/vt-d: Unnecessary to handle default identity domain
iommu/vt-d: Allow devices with RMRRs to use identity domain
iommu/vt-d: Add RMRR base and end addresses sanity check
iommu/vt-d: Mark firmware tainted if RMRR fails sanity check
iommu/amd: Remove unused struct member
iommu/amd: Replace two consecutive readl calls with one readq
iommu/vt-d: Don't reject Host Bridge due to scope mismatch
PCI/ATS: Add PASID stubs
iommu/arm-smmu-v3: Return -EBUSY when trying to re-add a device
iommu/arm-smmu-v3: Improve add_device() error handling
iommu/arm-smmu-v3: Use WRITE_ONCE() when changing validity of an STE
iommu/arm-smmu-v3: Add second level of context descriptor table
iommu/arm-smmu-v3: Prepare for handling arm_smmu_write_ctx_desc() failure
iommu/arm-smmu-v3: Propagate ssid_bits
iommu/arm-smmu-v3: Add support for Substream IDs
iommu/arm-smmu-v3: Add context descriptor tables allocators
iommu/arm-smmu-v3: Prepare arm_smmu_s1_cfg for SSID support
ACPI/IORT: Parse SSID property of named component node
...
- Fix memory leak in pci_iov_add_virtfn() (Navid Emamdoost)
- Extend pci_add_dma_alias() so it can add a range of aliases (James
Sewart)
- Add DMA aliases for PLX PEX NTB (James Sewart)
* pci/virtualization:
PCI: Add DMA alias quirk for PLX PEX NTB
PCI: Add nr_devfns parameter to pci_add_dma_alias()
PCI: Fix pci_add_dma_alias() bitmask size
PCI/IOV: Fix memory leak in pci_iov_add_virtfn()
The current DMA alias implementation requires the aliased device be on the
same PCI bus as the requester ID. Add an arch-specific mechanism to point
to another PCI device when doing mapping and PCI DMA alias search. The
default case returns the actual device.
Link: https://lore.kernel.org/r/1579613871-301529-4-git-send-email-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Christoph Hellwig <hch@lst.de>
When resuming from hibernation (S4, also known as "suspend to disk") on a
VM, we have seen invalid config space, e.g.,
serial 0000:00:16.3: restoring config space at offset 0x14 (was 0x9104e000, writing 0xffffffff)
To help debug problems like this, log the config space being saved before
suspend, similar to the log in pci_restore_config_dword() when resuming.
Link: https://lore.kernel.org/r/20200113060724.19571-1-yu.c.chen@intel.com
[bhelgaas: commit log]
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Len Brown <lenb@kernel.org>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Building drivers for ATS-aware IOMMUs as modules requires access to
pci_ats_disabled(). Export it as a GPL symbol to get things working.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
Tested-by: John Garry <john.garry@huawei.com> # smmu v3
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add a "nr_devfns" parameter to pci_add_dma_alias() so it can be used to
create DMA aliases for a range of devfns.
[bhelgaas: incorporate nr_devfns fix from James, update
quirk_pex_vca_alias() and setup_aliases()]
Signed-off-by: James Sewart <jamessewart@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The number of possible devfns is 256, but pci_add_dma_alias() allocated a
bitmap of size 255. Fix this off-by-one error.
This fixes commits 338c3149a2 ("PCI: Add support for multiple DMA
aliases") and c663579273 ("PCI: Allocate dma_alias_mask with
bitmap_zalloc()"), but I doubt it was possible to see a problem because
it takes 4 64-bit longs (or 8 32-bit longs) to hold 255 bits, and
bitmap_zalloc() doesn't save the 255-bit size anywhere.
[bhelgaas: commit log, move #define to drivers/pci/pci.h, include loop
limit fix from Qian Cai:
https://lore.kernel.org/r/20191218170004.5297-1-cai@lca.pw]
Signed-off-by: James Sewart <jamessewart@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
-----BEGIN PGP SIGNATURE-----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=uUXw
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the
MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA devices
downstream (Subbaraya Sundeep)
* pci/resource:
PCI: Do not use bus number zero from EA capability
PCI: Avoid double hpmemsize MMIO window assignment
PCI: Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters
PCI: Add PCI_STD_NUM_BARS for the number of standard BARs
PCI: Fix missing bridge dma_ranges resource list cleanup
PCI: Protect pci_reassign_bridge_resources() against concurrent addition/removal
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we only
did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0) instead
of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
* pci/pm:
PCI/PM: Move pci_dev_wait() definition earlier
PCI/PM: Add missing link delays required by the PCIe spec
PCI/PM: Add pcie_wait_for_link_delay()
PCI/PM: Return error when changing power state from D3cold
PCI/PM: Decode D3cold power state correctly
PCI/PM: Fold __pci_complete_power_transition() into its caller
PCI/PM: Avoid exporting __pci_complete_power_transition()
PCI/PM: Fold __pci_start_power_transition() into its caller
PCI/PM: Use pci_power_up() in pci_set_power_state()
PCI/PM: Move power state update away from pci_power_up()
PCI/PM: Remove unused pci_driver.suspend_late() hook
PCI/PM: Remove unused pci_driver.resume_early() hook
xen-platform: Convert to generic power management
PCI/PM: Simplify pci_set_power_state()
PCI/PM: Expand PM reset messages to mention D3hot (not just D3)
PCI/PM: Apply D2 delay as milliseconds, not microseconds
PCI/PM: Use pci_WARN() to include device information
PCI/PM: Use PCI dev_printk() wrappers for consistency
PCI/PM: Wrap long lines in documentation
PCI/PM: Note that PME can be generated from D0
PCI/PM: Make power management op coding style consistent
PCI/PM: Run resume fixups before disabling wakeup events
PCI/PM: Clear PCIe PME Status even for legacy power management
PCI/PM: Correct pci_pm_thaw_noirq() documentation
PCI/PM: Always return devices to D0 when thawing
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC even
if platform didn't grant control over AER (Olof Johansson)
* pci/aer:
PCI/DPC: Add "pcie_ports=dpc-native" to allow DPC without AER control
PCI/AER: Fix kernel-doc warnings
PCI/AER: Use for_each_set_bit() to simplify code
PCI/AER: Add PoisonTLPBlocked to Uncorrectable error counters
PCI/AER: Save AER Capability for suspend/resume
Some more development work for v5.5. Highlights include:
- More cleanups from Morimoto-san.
- Trigger word detection for RT5677.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl3bzrQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LkMB/4/MkpN4F2WudNCKgmYay2gw3hq8aOR
5Xh/SE6N3BEgBpQiMEUdePRT6LqnQMsSpOaUoKfd4nFvCyLaV7itaYzQuUpo+UJ/
a4UDHJPVfrDJeFghWqSngfEW/N66mpO3UuAvhSRTR3ku0T31v9FkcLsMbdxVUpLC
ablSaFfPCOtTQOsG9blRUL/GAWUhGzPI/Hl4VldS0FvKDmMDY2fxt7QxXRaEYItc
i1Uthklxd0BfRmDqv0WEpduUhbwzg6Uir9pXSisux7DpMk1Li0IyPST5UcRl0Zf4
CKL/qfdQANpufj9kGmrlCOnXB9P5/XYVwfYV430WqMyw0QaOzzSrxT7C
=CZ/+
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: More updates for v5.5
Some more development work for v5.5. Highlights include:
- More cleanups from Morimoto-san.
- Trigger word detection for RT5677.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove <linux/pci.h> and <linux/msi.h> from being included directly as part
of the include/linux/of_pci.h, and remove superfluous declaration of struct
of_phandle_args.
Move users of include <linux/of_pci.h> to include <linux/pci.h> and
<linux/msi.h> directly rather than rely on both being included transitively
through <linux/of_pci.h>.
Link: https://lore.kernel.org/r/20190903113059.2901-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Move the definition of pci_dev_wait() above pci_power_up() so that it can
be called from the latter with no change in functionality. This is a pure
code move with no functional change.
Link: https://lore.kernel.org/r/20191120051743.23124-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently Linux does not follow PCIe spec regarding the required delays
after reset. A concrete example is a Thunderbolt add-in-card that consists
of a PCIe switch and two PCIe endpoints:
+-1b.0-[01-6b]----00.0-[02-6b]--+-00.0-[03]----00.0 TBT controller
+-01.0-[04-36]-- DS hotplug port
+-02.0-[37]----00.0 xHCI controller
\-04.0-[38-6b]-- DS hotplug port
The root port (1b.0) and the PCIe switch downstream ports are all PCIe Gen3
so they support 8GT/s link speeds.
We wait for the PCIe hierarchy to enter D3cold (runtime):
pcieport 0000:00:1b.0: power state changed by ACPI to D3cold
When it wakes up from D3cold, according to the PCIe 5.0 section 5.8 the
PCIe switch is put to reset and its power is re-applied. This means that we
must follow the rules in PCIe 5.0 section 6.6.1.
For the PCIe Gen3 ports we are dealing with here, the following applies:
With a Downstream Port that supports Link speeds greater than 5.0 GT/s,
software must wait a minimum of 100 ms after Link training completes
before sending a Configuration Request to the device immediately below
that Port. Software can determine when Link training completes by polling
the Data Link Layer Link Active bit or by setting up an associated
interrupt (see Section 6.7.3.3).
Translating this into the above topology we would need to do this (DLLLA
stands for Data Link Layer Link Active):
0000:00:1b.0: wait for 100 ms after DLLLA is set before access to 0000:01:00.0
0000:02:00.0: wait for 100 ms after DLLLA is set before access to 0000:03:00.0
0000:02:02.0: wait for 100 ms after DLLLA is set before access to 0000:37:00.0
I've instrumented the kernel with some additional logging so we can see the
actual delays performed:
pcieport 0000:00:1b.0: power state changed by ACPI to D0
pcieport 0000:00:1b.0: waiting for D3cold delay of 100 ms
pcieport 0000:00:1b.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:01.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:04.0: waiting for D3hot delay of 10 ms
For the switch upstream port (01:00.0 reachable through 00:1b.0 root port)
we wait for 100 ms but not taking into account the DLLLA requirement. We
then wait 10 ms for D3hot -> D0 transition of the root port and the two
downstream hotplug ports. This means that we deviate from what the spec
requires.
Performing the same check for system sleep (s2idle) transitions it turns
out to be even worse. None of the mandatory delays are performed. If this
would be S3 instead of s2idle then according to PCI FW spec 3.2 section
4.6.8. there is a specific _DSM that allows the OS to skip the delays but
this platform does not provide the _DSM and does not go to S3 anyway so no
firmware is involved that could already handle these delays.
On this particular platform these delays are not actually needed because
there is an additional delay as part of the ACPI power resource that is
used to turn on power to the hierarchy but since that additional delay is
not required by any of standards (PCIe, ACPI) it is not present in the
Intel Ice Lake, for example where missing the mandatory delays causes
pciehp to start tearing down the stack too early (links are not yet
trained). Below is an example how it looks like when this happens:
pcieport 0000:83:04.0: pciehp: Slot(4): Card not present
pcieport 0000:87:04.0: PME# disabled
pcieport 0000:83:04.0: pciehp: pciehp_unconfigure_device: domain🚌dev = 0000:86:00
pcieport 0000:86:00.0: Refused to change power state, currently in D3
pcieport 0000:86:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x201ff)
pcieport 0000:86:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
...
There is also one reported case (see the bugzilla link below) where the
missing delay causes xHCI on a Titan Ridge controller fail to runtime
resume when USB-C dock is plugged. This does not involve pciehp but instead
the PCI core fails to runtime resume the xHCI device:
pcieport 0000:04:02.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
pcieport 0000:04:02.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100406)
xhci_hcd 0000:39:00.0: Refused to change power state, currently in D3
xhci_hcd 0000:39:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x1ff)
xhci_hcd 0000:39:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
...
Add a new function pci_bridge_wait_for_secondary_bus() that is called on
PCI core resume and runtime resume paths accordingly if the bridge entered
D3cold (and thus went through reset).
This is second attempt to add the missing delays. The previous solution in
c2bf1fc212 ("PCI: Add missing link delays required by the PCIe spec") was
reverted because of two issues it caused:
1. One system become unresponsive after S3 resume due to PME service
spinning in pcie_pme_work_fn(). The root port in question reports that
the xHCI sent PME but the xHCI device itself does not have PME status
set. The PME status bit is never cleared in the root port resulting
the indefinite loop in pcie_pme_work_fn().
2. Slows down resume if the root/downstream port does not support Data
Link Layer Active Reporting because pcie_wait_for_link_delay() waits
1100 ms in that case.
This version should avoid the above issues because we restrict the delay to
happen only if the port went into D3cold.
Link: https://lore.kernel.org/linux-pci/SL2P216MB01878BBCD75F21D882AEEA2880C60@SL2P216MB0187.KORP216.PROD.OUTLOOK.COM/
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203885
Link: https://lore.kernel.org/r/20191112091617.70282-3-mika.westerberg@linux.intel.com
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pcie_wait_for_link_delay(). Similar to pcie_wait_for_link() but allows
passing custom activation delay in milliseconds.
Link: https://lore.kernel.org/r/20191112091617.70282-2-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pci_raw_set_power_state() uses the Power Management capability to change a
device's power state. The capability is in config space, which is
accessible in D0, D1, D2, and D3hot, but not in D3cold.
If we call pci_raw_set_power_state() on a device that's in D3cold, config
reads fail and return ~0 data, which we erroneously interpreted as "the
device is in D3hot", leading to messages like this:
pcieport 0000:03:00.0: Refused to change power state, currently in D3
The PCI_PM_CTRL has several RsvdP fields, so ~0 is never a valid register
value. If we get that value, print a more informative message and return
an error.
Changing the power state of a device from D3cold must be done by a platform
power management method or some other non-config space mechanism.
Link: https://lore.kernel.org/r/20190822200551.129039-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use pci_power_name() to print pci_power_t correctly. This changes:
"state 0" or "D0" to "D0"
"state 1" or "D1" to "D1"
"state 2" or "D2" to "D2"
"state 3" or "D3" to "D3hot"
"state 4" or "D4" to "D3cold"
Changes dmesg logging only, no other functional change intended.
Link: https://lore.kernel.org/r/20190822200551.129039-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Because pci_set_power_state() has become the only caller of
__pci_complete_power_transition(), there is no need for the latter to
be a separate function any more, so fold it into the former, drop a
redundant check and reduce the number of lines of code somewhat.
Code rearrangement, no intentional functional impact.
Link: https://lore.kernel.org/r/15576968.k611qn3UU0@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Notice that radeon_set_suspend(), which is the only caller of
__pci_complete_power_transition() outside of pci.c, really only
cares about the pci_platform_power_transition() invoked by it,
so export the latter instead of it, update the radeon driver to
call pci_platform_power_transition() directly and make
__pci_complete_power_transition() static.
Code rearrangement, no intentional functional impact.
Link: https://lore.kernel.org/r/1731661.ykamz2Tiuf@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Because pci_power_up() has become the only caller of
__pci_start_power_transition(), there is no need for the latter to
be a separate function any more, so fold it into the former, drop a
redundant check and reduce the number of lines of code somewhat.
Code rearrangement, no intentional functional impact.
Link: https://lore.kernel.org/r/3458080.lsoDbfkST9@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Make it explicitly clear that the code to put devices into D0 in
pci_set_power_state() and in pci_pm_default_resume_early() is the
same by making the latter use pci_power_up() for transitions into D0.
Code rearrangement, no intentional functional impact.
Link: https://lore.kernel.org/r/2520019.OZ1nXS5aSj@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Move the invocation of pci_update_current_state() from pci_power_up() to
pci_pm_default_resume_early(), which is the only caller of that function.
Preparatory change, no functional impact.
Link: https://lore.kernel.org/r/37482337.udjOGdOKNb@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Check for the PCI_DEV_FLAGS_NO_D3 quirk early, before calling
__pci_start_power_transition(). This way all the cases where we don't need
to do anything at all are checked up front.
This doesn't fix anything because if the caller requested D3hot or D3cold,
__pci_start_power_transition() is a no-op. But calling it is pointless and
makes the code harder to analyze.
Link: https://lore.kernel.org/r/20191101204558.210235-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pci_pm_reset() resets a device by putting it in D3hot and bringing it back
to D0. Clarify related messages to mention "D3hot" explicitly instead of
just "D3".
Link: https://lore.kernel.org/r/20191101204558.210235-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PCI_PM_D2_DELAY is defined as 200, which is milliseconds, but previously we
used udelay(), which only waited for 200 microseconds. Use msleep()
instead so we wait the correct amount of time. See PCIe r5.0, sec 5.9.
Link: https://lore.kernel.org/r/20191101204558.210235-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The existing "pci=hpmemsize=nn[KMG]" kernel parameter overrides the default
size of both the non-prefetchable and the prefetchable MMIO windows for
hotplug bridges.
Add "pci=hpmmiosize=nn[KMG]" to override the default size of only the
non-prefetchable MMIO window.
Add "pci=hpmmioprefsize=nn[KMG]" to override the default size of only the
prefetchable MMIO window.
Link: https://lore.kernel.org/r/SL2P216MB0187E4D0055791957B7E2660806B0@SL2P216MB0187.KORP216.PROD.OUTLOOK.COM
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
A driver may want to know the existence of _PR3, to choose different
runtime suspend behavior. A user will be add in next patch.
This is mostly the same as nouveau_pr3_present().
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20191018073848.14590-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Previously we did not save and restore the AER configuration on
suspend/resume, so the configuration may be lost after resume.
Save the AER configuration during suspend and restore it during resume.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/92EBB4272BF81E4089A7126EC1E7B28492C3B007@IRSMSX101.ger.corp.intel.com
Signed-off-by: Mayurkumar Patel <mayurkumar.patel@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is an arbitrary difference between the system resume and
runtime resume code paths for PCI devices regarding the delay to
apply when switching the devices from D3cold to D0.
Namely, pci_restore_standard_config() used in the runtime resume
code path calls pci_set_power_state() which in turn invokes
__pci_start_power_transition() to power up the device through the
platform firmware and that function applies the transition delay
(as per PCI Express Base Specification Revision 2.0, Section 6.6.1).
However, pci_pm_default_resume_early() used in the system resume
code path calls pci_power_up() which doesn't apply the delay at
all and that causes issues to occur during resume from
suspend-to-idle on some systems where the delay is required.
Since there is no reason for that difference to exist, modify
pci_power_up() to follow pci_set_power_state() more closely and
invoke __pci_start_power_transition() from there to call the
platform firmware to power up the device (in case that's necessary).
Fixes: db288c9c5f ("PCI / PM: restore the original behavior of pci_set_power_state()")
Reported-by: Daniel Drake <drake@endlessm.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Link: https://lore.kernel.org/linux-pm/CAD8Lp44TYxrMgPLkHCqF9hv6smEurMXvmmvmtyFhZ6Q4SE+dig@mail.gmail.com/T/#m21be74af263c6a34f36e0fc5c77c5449d9406925
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Code that iterates over all standard PCI BARs typically uses
PCI_STD_RESOURCE_END. However, that requires the unusual test
"i <= PCI_STD_RESOURCE_END" rather than something the typical
"i < PCI_STD_NUM_BARS".
Add a definition for PCI_STD_NUM_BARS and change loops to use the more
idiomatic C style to help avoid fencepost errors.
Link: https://lore.kernel.org/r/20190927234026.23342-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190927234308.23935-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190916204158.6889-3-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # arch/s390/
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> # video/fbdev/
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> # pci/controller/dwc/
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> # scsi/pm8001/
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> # scsi/pm8001/
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # memstick/
- Convert pci_resource_to_user() to a weak function to remove
HAVE_ARCH_PCI_RESOURCE_TO_USER #defines (Denis Efremov)
- Use PCI_SRIOV_NUM_BARS for idiomatic loop structure (Denis Efremov)
- Fix Resizable BAR size suspend/restore for 1MB BARs (Sumit Saxena)
- Correct "pci=resource_alignment" example in documentation (Alexey
Kardashevskiy)
* pci/resource:
PCI: Correct pci=resource_alignment parameter example
PCI: Restore Resizable BAR size bits correctly for 1MB BARs
PCI: Use PCI_SRIOV_NUM_BARS in loops instead of PCI_IOV_RESOURCE_END
PCI: Convert pci_resource_to_user() to a weak function
# Conflicts:
# drivers/pci/pci.c
- Use devm_add_action_or_reset() helper (Fuqian Huang)
- Mark expected switch fall-through (Gustavo A. R. Silva)
- Convert sysfs device attributes from __ATTR() to DEVICE_ATTR() (Kelsey
Skunberg)
- Convert sysfs file permissions from S_IRUSR etc to octal (Kelsey
Skunberg)
- Move SR-IOV sysfs functions to iov.c (Kelsey Skunberg)
- Add pci_info_ratelimited() to ratelimit PCI messages separately
(Krzysztof Wilczynski)
- Fix "'static' not at beginning of declaration" warnings (Krzysztof
Wilczynski)
- Clean up resource_alignment parameter to not require static buffer
(Logan Gunthorpe)
- Add ACS quirk for iProc PAXB (Abhinav Ratna)
- Add pci_irq_vector() and other stubs for !CONFIG_PCI (Herbert Xu)
* pci/misc:
PCI: Add pci_irq_vector() and other stubs when !CONFIG_PCI
PCI: Add ACS quirk for iProc PAXB
PCI: Force trailing new line to resource_alignment_param in sysfs
PCI: Move pci_[get|set]_resource_alignment_param() into their callers
PCI: Clean up resource_alignment parameter to not require static buffer
PCI: Use static const struct, not const static struct
PCI: Add pci_info_ratelimited() to ratelimit PCI separately
PCI/IOV: Remove group write permission from sriov_numvfs, sriov_drivers_autoprobe
PCI/IOV: Move sysfs SR-IOV functions to iov.c
PCI: sysfs: Change permissions from symbolic to octal
PCI: sysfs: Change DEVICE_ATTR() to DEVICE_ATTR_WO()
PCI: sysfs: Define device attributes with DEVICE_ATTR*()
PCI: Mark expected switch fall-through
PCI: Use devm_add_action_or_reset()
In some systems, the Device/Port Type in the PCI Express Capabilities
register incorrectly identifies upstream ports as downstream ports.
d0751b98df ("PCI: Add dev->has_secondary_link to track downstream PCIe
links") addressed this by adding pci_dev.has_secondary_link, which is set
for downstream ports. But this is confusing because pci_pcie_type()
sometimes gives the wrong answer, and it's not obvious that we should use
pci_dev.has_secondary_link instead.
Reduce the confusion by correcting the type of the port itself so that
pci_pcie_type() returns the actual type regardless of what the Device/Port
Type register claims it is. Update the users to call pci_pcie_type() and
pcie_downstream_port() accordingly, and remove pci_dev.has_secondary_link
completely.
Link: https://lore.kernel.org/linux-pci/20190703133953.GK128603@google.com/
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20190822085553.62697-2-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When 'pci=resource_alignment=' is specified on the command line, there is
no trailing new line. Then, when it's read through the corresponding sysfs
attribute, there will be no newline and a cat command will not show
correctly in a shell. If the parameter is set through sysfs a new line will
be stored and it will 'cat' correctly.
To solve this, append a new line character in the show function if one does
not already exist.
Link: https://lore.kernel.org/r/20190822161013.5481-4-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Both the functions pci_get_resource_alignment_param() and
pci_set_resource_alignment_param() are now only called in one place:
resource_alignment_show() and resource_alignment_store() respectively.
There is no value in this extra set of functions so move both into their
callers respectively.
[bhelgaas: fold in "GFP_KERNEL while atomic" fix from Christoph Hellwig
<hch@infradead.org>
https://lore.kernel.org/r/20190902075006.GB754@infradead.org]
Link: https://lore.kernel.org/r/20190822161013.5481-3-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Clean up the 'resource_alignment' parameter code to use kstrdup() in the
initcall routine instead of a static buffer that wastes memory regardless
of whether the feature is used. This allows us to drop 'COMMAND_LINE_SIZE'
bytes (typically 256-4096 depending on architecture) of static data.
This is similar to what has been done for the 'disable_acs_redir'
parameter.
Link: https://lore.kernel.org/r/20190822161013.5481-2-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Do not use printk_ratelimit() in drivers/pci/pci.c as it shares the rate
limiting state with all other callers to the printk_ratelimit().
Add pci_info_ratelimited() (similar to pci_notice_ratelimited() added in
the commit a88a7b3eb0 ("vfio: Use dev_printk() when possible")) and use
it instead of printk_ratelimit() + pci_info().
Link: https://lore.kernel.org/r/20190825224616.8021-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In a Resizable BAR Control Register, bits 13:8 control the size of the BAR.
The encoded values of these bits are as follows (see PCIe r5.0, sec
7.8.6.3):
Value BAR size
0 1 MB (2^20 bytes)
1 2 MB (2^21 bytes)
2 4 MB (2^22 bytes)
...
43 8 EB (2^63 bytes)
Previously we incorrectly set the BAR size bits for a 1 MB BAR to 0x1f
instead of 0, so devices that support that size, e.g., new megaraid_sas and
mpt3sas adapters, fail to initialize during resume from S3 sleep.
Correctly calculate the BAR size bits for Resizable BAR control registers.
Link: https://lore.kernel.org/r/20190725192552.24295-1-sumit.saxena@broadcom.com
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203939
Fixes: d3252ace0b ("PCI: Restore resized BAR state on resume")
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org # v4.19+
Fix typos in drivers/pci. Comment and whitespace changes only.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
In pci_pm_complete() there are checks to decide whether or not to
resume devices that were left in runtime-suspend during the preceding
system-wide transition into a sleep state. They involve checking the
current power state of the device and comparing it with the power
state of it set before the preceding system-wide transition, but the
platform component of the device's power state is not handled
correctly in there.
Namely, on platforms with ACPI, the device power state information
needs to be updated with care, so that the reference counters of
power resources used by the device (if any) are set to ensure that
the refreshed power state of it will be maintained going forward.
To that end, introduce a new ->refresh_state() platform PM callback
for PCI devices, for asking the platform to refresh the device power
state data and ensure that the corresponding power state will be
maintained going forward, make it invoke acpi_device_update_power()
(for devices with ACPI PM) on platforms with ACPI and make
pci_pm_complete() use it, through a new pci_refresh_power_state()
wrapper function.
Fixes: a0d2a959d3 (PCI: Avoid unnecessary resume after direct-complete)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Linus Torvalds