sh_mipi uses some clocks, but the method of setup depends on CPU.
Current SuperH (like sh73a0) can control all of these clocks
by CPG (Clock Pulse Generator).
It means we can control it by clock framework only.
But on sh7372, it needs CPG settings AND sh_mipi PHYCTRL::PLLDS,
and only sh7372 has PHYCTRL::PLLDS.
But on current sh_mipi driver, PHYCTRL::PLLDS of sh7372 was
overwrote since the callback timing of clock setting was changed
by c2658b70f0
(fbdev: sh_mipi_dsi: fixup setup timing of sh_mipi_setup()).
To solve this issue, this patch adds extra .phyctrl.
This patch adds detail explanation for unclear mipi settings
and fixup wrong PHYCTRL::PLLDS value for ap4evb (0xb -> 0x6).
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
MERAM can be used for other IP blocks as well in the future.
It doesn't necessarily mean that the MERAM driver depends on the LCDC.
This patch corrects dependency.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Add timing data for Hitachi SP10Q010 display and allow configuration
of the 4bpp palette. For 4bpp framebuffer enable reversed order of
pixels in a byte. This requires defining FB_CFB_REV_PIXELS_IN_BYTE
and additionally setting var.nonstd to the value FB_NONSTD_REV_PIX_IN_B.
Note that it is not enough to set da8xx_fb_var.nonstd to this value
statically, since FBIOPUT_VSCREENINFO ioctl might pass var struct with
.nonstd field set to zero or another value. Therefore this setting must
be adjusted in fb_check_var() according to the requested bpp value.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
PV-on-HVM guests may want to use the xen keyboard/mouse frontend, but
they don't use the xen frame buffer frontend. For this case it doesn't
make much sense for INPUT_XEN_KBDDEV_FRONTEND to depend on
XEN_FBDEV_FRONTEND. The opposite direction always makes more sense, i.e.
if you're using xenfb, then you'll want xenkbd. Switch the dependencies.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
strict_strtoul() writes a long but ->gamma_mode only has space to store an
int, so on 64 bit systems we end up scribbling over ->gamma_table_count as
well. I've changed it to use kstrtouint() instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'ep93xx-for-arm-soc' of git://github.com/RyanMallon/linux-2.6:
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-s3c2440/common.h
The USB graphics card driver delays the unregistering of the framebuffer
device to a workqueue, which breaks the userspace visible remove uevent
sequence. Recent userspace tools started to support USB graphics card
hotplug out-of-the-box and rely on proper events sent by the kernel.
The framebuffer device is a direct child of the USB interface which is
removed immediately after the USB .disconnect() callback. But the fb device
in /sys stays around until its final cleanup, at a time where all the parent
devices have been removed already.
To work around that, we remove the sysfs fb device directly in the USB
.disconnect() callback and leave only the cleanup of the internal fb
data to the delayed work.
Before:
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2 (usb)
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0 (usb)
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/graphics/fb0 (graphics)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0 (usb)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2 (usb)
remove /2-1.2:1.0/graphics/fb0 (graphics)
After:
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2 (usb)
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0 (usb)
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/graphics/fb1 (graphics)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/graphics/fb1 (graphics)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0 (usb)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2 (usb)
Cc: stable@vger.kernel.org
Tested-by: Bernie Thompson <bernie@plugable.com>
Acked-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The ep93xx backlight driver uses a single register within the
framebuffer's register space. Currently the backlight driver uses a
static IO mapping for the register since the memory cannot be
requested by both drivers.
Convert the static mapping to use ioremap so that we can remove the
dependency on mach/hardware.h. To do so, we need remove the
request_mem_region from both the backlight and framebuffer drivers,
since whichever driver is loaded second will fail with -EBUSY
otherwise.
A proper fix is still required, and a FIXME comment has been added to
both drivers.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Convert calls to free_irq so that the second argument is the same as the
last argument of the corresponding call to request_irq. Without this
property, free_irq does nothing.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
* 'next/cleanup-exynos-clock' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
(includes an update to v3.3-rc6)
Currently the shadow-dirty flags for manual update displays is cleared
in the apply_irq_handler when an update has finished. This is not
correct, as the shadow registers are taken into use (i.e. after that
they are not dirty) when the update is started.
Move the mgr_clear_shadow_dirty() call from apply_irq_handler to
dss_mgr_start_update() to fix this.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Supporting runtime PM is very nice, but that's not a reason not to
implement system suspend/resume properly.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The meram_register(), meram_unregister() and meram_update() operations
check that the pointers they get from the caller are not NULL. Those
checks can be remove, as the caller already ensures that the pointers
are valid.
The platform sanity checks can also be removed, as the operations can't
be accessed without valid platform data anyway.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Remove the RGB or Y/C base address update from the meram_register()
operation, as this belongs to the meram_update() operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of copying the whole platform data structure to struct
sh_mobile_lcdc_chan, store a const pointer to the channel platform data.
MERAM configuration information needs to be changed at runtime, so copy
it to struct sh_mobile_lcdc_chan.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of manually specifying the ICBs to use in platform data,
allocate them automatically at runtime. The range of reserved ICBs (for
instance to be used through UIO), if any, is passed in the platform data
reserved_icbs field as a bitmask.
The MERAM registration function now returns a pointer to an opaque MERAM
object, which is passed to the update and unregistration functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of requiring the users to hardcode MERAM allocation in platform
data, allocate blocks at runtime using genalloc.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Let the compiler decide which complex functions to inline, and constify
constant static arrays.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The new structure stores ICB parameters for ICBs.
Instead of modifying the struct sh_mobile_meram_cfg instances passed by
callers, store the ICB parameters internally and make the public API
take const pointers to sh_mobile_meram_cfg.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Many variables, such as loop counters, sizes and offsets, should be
unsigned integers. Make them so.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The structure describe ICB configuration, no ICB objects themselves.
Rename it to sh_mobile_meram_icb_cfg in preparation for the addition of
an ICB structure.
All the structure fields are unsigned integers, make them so.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The sh_mobile_wait_for_vsync() function isn't related to the fbdev API,
make it generic by passing a channel pointer instead of an fb_info
pointer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Store the frame buffer configuration (colorspace, visible/virtual
horizontal and vertical resolutions and line pitch) in the
sh_mobile_lcdc_chan structure, and use it instead of accessing fb_info.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The dma_map_sg() and dma_unmap_sg() functions need a pointer to the
physical device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Store the active format in the channel structure, and use it instead of
parsing info->var all over the place when the format is needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The function returns a pointer to a structure describing a format based
on its fourcc. Use the function where applicable instead of hardcoded
switch-case statements.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Group fields by purpose, and make the separation between core fields and
FB-related fields clear.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The struct sh_mobile_lcdc_chan_cfg platform data contains a list of
video modes. Name the lcd_cfg and num_cfg fields to reflect that they
describe video modes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Embed struct fb_videomode instead of struct fb_var_screeninfo in struct
sh_mobile_lcdc_chan to store the display mode.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The LCDC fb_info structure is only used to retrieve the default video
mode in case none of the modes advertised by EDID information is
acceptable. Pass a pointer to the default mode through the
sh_mobile_lcdc_entity structure instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The struct sh_hdmi mode field is only used after being assigned by the
EDID read code. There is thus no need to initialize it from the LCDC
display var in the display on handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Pass pointers to struct fb_videomode and struct fb_monspecs instead of
struct fb_var_screeninfo to the notify callback.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of accessing the LCDC channel and fb_info structures directly,
use the LCDC notification callback to inform the LCDC driver about
display-related events.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The callback implements 3 notification events:
- SH_MOBILE_LCDC_EVENT_DISPLAY_CONNECT notifies the LCDC that the
display has been connected
- SH_MOBILE_LCDC_EVENT_DISPLAY_DISCONNECT notifies the LCDC that the
display has been disconnected
- SH_MOBILE_LCDC_EVENT_DISPLAY_MODE notifies that LCDC that a display
mode has been detected
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Return true if the display is connected and false otherwise. Set the fb
info state to FBINFO_STATE_SUSPENDED in the sh_mobile_lcdc driver when
the display is not connected.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The fb_info parameter passed to the display_on operation will be
removed, don't use it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The field will be used by the transmitter drivers to access
sh_mobile_lcdc_chan fields such as fb_info.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The display_on/off operations are now accessed through the
sh_mobile_lcdc_entity operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The display_on/off operations are now accessed through the
sh_mobile_lcdc_entity operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Pass a pointer to the transmitter device through platform data, retrieve
the corresponding sh_mobile_lcdc_entity structure in the probe method
and call the transmitter display_on/off methods directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The sh_mobile_lcdc_entity structure will be used to abstract operations
performed by transceivers (such as MIPI/DSI and HDMI).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of relying on info->par being a pointer to an LCDC channel, cast
the notifier block pointer to an sh_hdmi pointer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Pass a pointer to a struct sh_mobile_lcdc_priv instead, which stores a
pointer to the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The pm_runtime_enable() and pm_runtime_resume() calls don't belong to
sh_mobile_lcdc_setup_clocks(). Move them to the probe function. Remove
the unneeded pm_runtime_resume() call.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
default_720p and sh_mobile_lcdc_check_interface are used at device
initialization time only. Mark them as __devinitconst and __devinit
respectively.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Make the driver more readable by reordering code and splitting it into
logical sections. Reorder the headers alphabetically.
No modification to the code have been performed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
* 'board' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: add minimal support for Nokia RM-696
ARM: OMAP: enable Bluetooth on the PandaBoard
ARM: OMAP: pandora: add support for backlight and poweroff
ARM: OMAP4: board-4430sdp: don't initialize value that is never used
ARM: OMAP3: cm-t3517: add EMAC support
ARM: OMAP: move generic EMAC init to separate file
ARM: OMAP3: RX-51: add explicit mux configuration of tsc2005 control gpios
ARM: OMAP: Add omap_reserve functionality
(includes sync-up to 3.3-rc6)
As check_var already ensures that the mode is valid there is no need
to do those expensive lookups here again. The only thing that might
change is that the deprecated interface could report slightly
different refresh rates due to rounding errors.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch converts the modetables used in viafb to
- remove the strange thing that sync_end and blanking_end contained
the length and not the absolute value
- remove hundreds of useless defines
- use fb_videomode and not our own definition so modes defined in
the subsystem and received via EDID are compatible with ours
As the modes are now stored in a flat structure and no longer in a
tree like thing the lookup time was increased but as it is a rare
event anyway it shouldn't matter. Otherwise the behaviour should be
the same as before.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
uvesafb_open may failed to save hardware state when kmalloc failed
in uvesafb_vbe_state_save, we should check this and notice user.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Return a negative errno instead of zero in the write function of
the sysfs entry in case of error.
Also add a check on the return value of dlfb_setup_modes().
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Acked-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
These are no longer needed with the recent iomap.h
changes.
Reported-by: Rob Herring <robherring2@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Since several sub modules such as backlight, leds and vibrator depend
on the refernce group and internal oscillator in pm8606, so modified
the power control of backlight in pm8606 by unified interface.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
wait_pending_extra_info_updates() currently does a hacky second check
for extra_info_update_ongoing() at the end of the function to show a
warning if extra_info update is still ongoing. The call to
extra_info_update_ongoing() should really be inside spinlock, but that's
a bit heavy just for verification.
Rather than that, check the return value of the
wait_for_completion_timeout() and print an error if it has timeouted or
returned an error.
Even better would be to return the error value and act on it in the
callers of wait_pending_extra_info_updates. However, it's not clear what
the callers should do in case of an error, as the error should only
happen if there's a bug in the driver or the HW. So we'll just print the
warning for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If DSS suspends within the functions dss_mgr_wait_for_go(),
dss_mgr_wait_for_go_ovl() or dss_mgr_wait_for_vsync(). It may lose it's clock
and lead to a register access failure.
Request runtime_pm around these functions.
[archit@ti.com: Moved runtime_pm calls to wait_for_go/vsync functions rather
then calling them from omap_dispc_wait_for_irq_interruptible_timeout()]
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
coef3_M8 had an incorrect phase with 50% more intensity. This resulted in
banding on slightly down/upscaled images. Fixed a rounding error in coef5_M9.
Also removed ARRAY_LEN macro as ARRAY_SIZE is the standard linux one.
Signed-off-by: Lajos Molnar <lajos@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add missing but supported color formats for GFX pipeline in dss features:
RGBX16-4444, RGBA16-4444 and XRGB16-1555.
In dispc_ovl_set_color_mode():
- Remove unsupported modes on GFX pipeline: YUV2 and UYVY. Replace these by
missing modes supported by GFX pipelines: RGBX16-4444 and RGBA16-4444.
- Fix swapped modes on VID pipelines: RGBX16-4444 and XRGB16-4444.
Signed-off-by: Lajos Molnar <lajos@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
While calculating regm and regmf value add using M2 divider in
the equation.
Formula for calculating:
Output clock on digital core domain:
CLKOUT = (M / (N+1))*CLKINP*(1/M2)
Internal oscillator output clock on internal LDO domain:
CLKDCOLDO = (M / (N+1))*CLKINP
The current code when allows variable M2 values as input
ignores using M2 divider values in calculation of regm and regmf.
so fix it by using M2 in calculation although the default value for
M2 is 1.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds s3c_fb_driverdata s3c_fb_data_exynos5 for EXYNOS5
and adds extended timing control setting.
EXYNOS5 FIMD needs extended setting for video timing control.
Additional bits are added to VIDTCON2, VIDWxxADD2, VIDOSDxA and
VIDOSDxB registers in order to set timing value for lager resolution.
Also, address offset of VIDTCONx registers is changed from 0x0
to 0x20000, thus variable type should be changed to int type
to handle the address offset of VIDTCONx registers for EXYNOS5 FIMD.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Otherwise we hit WARN_CONSOLE_UNLOCKED in do_unblank_screen
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch removes redundant bits per pixel information by using the
one storged in var directly. Simplifies code without any functional
changes.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Some user scenarios need to prioritize performance over
maxiumum resolution.
Also, some devices may have bad vendor descriptors, and
this allows the user to set a pixel limit that matches
their specific device to avoid blank screens on higher
resolution monitors.
700000 minimum for DL-115, 2360000 maximum for DL-195
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Bernie Thompson <bernie@plugable.com>
The driver was not using le16_to_cpu when reading keys from the vendor
descriptor, causing incorrect parsing. Mainly, sku_pixel_limit was not
being parsed on big-endian systems. This would result in a blank screen
on big-endian CPUs where the DL chips's max mode was smaller than the
monitor's native mode.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Bernie Thompson <bernie@plugable.com>
It includes:
- two fixes for OMAP HDMI
- one fix to make new OMAP functions behave as they are supposed to
- one Kconfig dependency fix
- two fixes for viafb for modesetting on VX900 hardware
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=+UnE
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.3-2' of git://github.com/schandinat/linux-2.6
fbdev fixes for 3.3 from Florian Tobias Schandinat
It includes:
- two fixes for OMAP HDMI
- one fix to make new OMAP functions behave as they are supposed to
- one Kconfig dependency fix
- two fixes for viafb for modesetting on VX900 hardware
* tag 'fbdev-fixes-for-3.3-2' of git://github.com/schandinat/linux-2.6:
OMAPDSS: APPLY: make ovl_enable/disable synchronous
OMAPDSS: panel-dvi: Add Kconfig dependency on I2C
viafb: fix IGA1 modesetting on VX900
viafb: select HW scaling on VX900 for IGA2
OMAPDSS: HDMI: hot plug detect fix
OMAPDSS: HACK: Ensure DSS clock domain gets out of idle when HDMI is enabled
This patch changes the ARCH name to "ARCH_S3C24XX" for Samsung
S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443,
and S3C2450 SoCs so that we can merge the mach-xxx directories
and plat-s3c24xx dir. to just one mach-s3c24xx for them.
I think this should be sent to upstream via samsung tree because
this touches many samsung stuff.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
[for the gadget part:]
Acked-by: Felipe Balbi <balbi@ti.com>
[for the framebuffer (video) part:]
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[For the watchdog-part:]
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fix race conditions with unplug/replug behavior, in particular
take care not to hold up USB probe/disconnect for long-running
framebuffer operations and rely on usb to handle teardown.
Fix for kernel panic reported with new F17 multiseat support.
Reported-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Bernie Thompson <bernie@plugable.com>
The main purpose of this patch is to fix several section mismatch
warnings from the board file and a few board specific drivers,
introduced with recent Amstrad Delta patch series, some of them rising
up only when building with CONFIG_MODULES not set.
While being at it, section tagging of all init data found in the board
file have been revised and hopefully corrected and/or optimized.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ovl->enable/disable are meant to be synchronous so that they can handle
the configuration of fifo sizes. The current kernel doesn't configure
fifo sizes yet, and so the code doesn't need to block to function (from
omapdss driver's perspective).
However, for the users of omapdss a non-blocking ovl->disable is
confusing, because they don't know when the memory area is not used
any more.
Furthermore, when the fifo size configuration is added in the next merge
window, the change from non-blocking to blocking could cause side
effects to the users of omapdss. So by making the functions block
already will keep them behaving in the same manner.
And, while not the main purpose of this patch, this will also remove the
compile warning:
drivers/video/omap2/dss/apply.c:350: warning:
'wait_pending_extra_info_updates' defined but not used
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
panel-dvi uses i2c, but the Kconfig didn't have dependency on I2C. Add
it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
* 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix L4_EMU_34XX_BASE error after iomap changes
ARM: OMAP2+: Limit omap_read/write usage to legacy USB drivers
ARM: OMAP: Remove plat/io.h by splitting it into mach/io.h and mach/hardware.h
ARM: OMAP2+: Move most of plat/io.h into local iomap.h
ARM: OMAP1: Move most of plat/io.h into local iomap.h
ARM: OMAP1: Move 16xx GPIO system clock to platform init code
ARM: OMAP: Move omap_init_consistent_dma_size() to local common.h
ARM: OMAP2+: Move SDRC related functions from io.h into local common.h
ARM: OMAP2+: Drop DISPC L3 firewall code
ARM: OMAP2xxx: PM: remove obsolete timer disable code in the suspend path
ARM: OMAP: McSPI: Remove unused flag from struct omap2_mcspi_device_config
(update to latest rmk/for-arm-soc branch)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is needed to minimize io.h so the SoC specific io.h
for ARMs can removed.
Note that minimal driver changes for DSS and RNG are needed to
include cpu.h for SoC detection macros.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is only needed when using SRAM for framebuffer,
and the support for SRAM framebuffer is about to get
removed.
Otherwise we cannot move most of plat/io.h to be a local
iomap.h for mach-omap2.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.15 (GNU/Linux)
iEYEABECAAYFAk9HE98ACgkQGkmNcg7/o7g4+QCfYIcWunicH7+tLMjH/h5MgHq2
S5EAoJdIKyAPfV1tsIY0ykJZQP+H4t4X
=QqTI
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
SuperH fixes for 3.3-rc5
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Fix sh2a build error for CONFIG_CACHE_WRITETHROUGH
sh: modify a resource of sh_eth_giga1_resources in board-sh7757lcr
arch/sh: remove references to cpu_*_map.
sh: Fix typo in pci-sh7780.c
sh: add platform_device for SPI1 in setup-sh7757
sh: modify resource for SPI0 in setup-sh7757
sh: se7724: fix compile breakage
sh: clkfwk: bugfix: use clk_reparent() for div6 clocks
sh: clock-sh7724: fixup sh_fsi clock settings
sh: sh7757lcr: update to the new MMCIF DMA configuration
sh: fix the sh_mmcif_plat_data in board-sh7757lcr
video: pvr2fb: Fix up spurious section mismatch warnings.
sh: Defer to asm-generic/device.h.
Convert the sa11x0 framebuffer driver to obtain the base address of its
hardware registers from the platform resources, and ioremap this rather
than relying on the static mappings.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The devm_ functions allocate memory that is released when a driver
detaches. This patch uses devm_request_irq of these functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
By using devm_ioremap, it also removes a potential memory leak, because
there was no call to iounmap in the probe function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Even if the documentation calls this bit "Reserved" it has to be set
to 0 for correct modesetting on IGA1.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@vger.kernel.org
VX900 can do hardware scaling for both IGAs in contrast to previous
hardware which could do it only for IGA2. This patch ensures that
we set the parameter for IGA2 and not for IGA1. This fixes hardware
scaling on VX900 until we have the infrastructure to support it for
both IGAs.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@vger.kernel.org
The "OMAPDSS: HDMI: PHY burnout fix" commit switched the HDMI driver
over to using a GPIO for plug detect. Unfortunately the ->detect()
method was not also updated, causing HDMI to no longer work for the
omapdrm driver (because it would actually check if a connection was
detected before attempting to enable display).
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For DSS clock domain to transition from idle to active state. It's necessary
to enable the optional clock DSS_FCLK before we enable the module using the
MODULEMODE bits in the clock domain's CM_DSS_DSS_CLKCTRL register.
This sequence was not followed correctly for the 'dss_hdmi' hwmod and it led
to DSS clock domain not getting out of idle when pm_runtime_get_sync() was
called for hdmi's platform device.
Since the clock domain failed to change it's state to active, the hwmod code
disables any clocks it had enabled before for this hwmod. This led to the clock
'dss_48mhz_clk' gettind disabled.
When hdmi's runtime_resume() op is called, the call to dss_runtime_get()
correctly enables the DSS clock domain this time. However, the clock
'dss_48mhz_clk' is needed for HDMI's PHY to function correctly. Since it was
disabled previously, the driver fails when it tries to enable HDMI's PHY.
Fix this for now by ensuring that dss_runtime_get() is called before we call
pm_runtime_get_sync() for hdmi's platform device. A correct fix for later would
be to modify the DSS related hwmod's mainclks, and also some changes in how
opt clocks are handled in the DSS driver.
This fixes the issue of HDMI not working when it's the default display. The
issue is not seen if any other display is already enabled as the first display
would have correctly enabled the DSS clockdomain.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that the old omapfb driver is only omap1 display driver, there's no
need to check if the arch is omap1. This patch removes the few remaining
checks for the arch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
include/linux/omapfb.h contains structs that are used only by the
omapfb driver. Move the structs into drivers/video/omap/omapfb.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapfb driver used platform_data to get fb memory areas and formats
defined by the board file.
This patch removes omapfb's (both old and new omapfb) use of the
memory data in platform_data, because:
- No board uses them currently
- It's not board file's job to define things like amount of default
framebuffer memory. These should come from the bootloader via command
line parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In an effort to clean up the old omapfb driver, this patch removes
HWA742 (the display chip used in N770) platform data. This can be done
as N770 is the only user of HWA742, and the platform data contains only
one field, te_connected, which we can just presume to be true in the
HWA742 driver.
This allows us to remove omapfb_set_ctrl_platform_data(), and the
mechanism to pass the platform data, in a later patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
OMAP SRAM can be used as video memory on OMAP1 and 2. However, there
usually is very little SRAM available, thus limiting its use, and no
board supported by the kernel currently uses it.
This patch removes the use of SRAM as video ram for the old omapfb
driver to simplify memory handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
OMAP SRAM can be used as video memory on OMAP1 and 2. However, there
usually is very little SRAM available, thus limiting its use, and no
board supported by the kernel currently uses it.
This patch removes the use of SRAM as video ram for the omapdss driver
to simplify memory handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Old omapfb driver (drivers/video/omap/) is no longer used for OMAP2+
devices, and thus we can remove OMAP2+ support from it and make it an
OMAP1 omapfb driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
N8x0's blizzard driver has been ported to new omapdss driver, so we can
now remove the old blizzard driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Rather than accessing GPSR and GPCR directly, use the GPIO subsystem
instead.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GPIO set and clear registers should only be written, rather than
read, modified, and written. A read-modify-write will have undesired
side effects.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sa1100fb driver needs to set the GPIO direction and alternate
function register according to the panel that we're driving. We've
done this in the driver by read-modify-writing the register, which
may cause problems with races. Fix this with a minimal change.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the LCD information is available while the driver is loaded,
we don't need to cache that information into our driver private data
structure. Get rid of it.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the assabet specific initialization for PAL output mode -
we call the lcd_power function before we enable the LCD controller,
which will disable the LCD panel to prevent it receiving incorrect
timings. Therefore, this setup here is redundant.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that we have platform data contained within the individual board
code, we can get rid of the global function pointers, placing them
inside the platform data instead.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move platform data out of the sa1100fb driver into the various
platform files themselves.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the LCD data structures to an include file which can be shared
with the board code in arch/arm/mach-sa1100.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the sa1100fb_mach_info structure to carry the RGB bitfield
overrides, rather than requiring them to be separately initialized
in sa1100fb_get_machine_info().
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the dev_xxx() macros for driver kernel message output, rather than
open coded printk() with KERN_ levels etc. Remove DPRINTK().
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The rgb structures should only be read and never written. Constify
them.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Annotate the driver structure with the .owner field, to allow the
module to be associated with the driver.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: drivers/video/built-in.o(.devinit.text+0x58): Section mismatch in reference from the function sa1100fb_probe() to the function .init.text:sa1100fb_init_fbinfo()
The function __devinit sa1100fb_probe() references
a function __init sa1100fb_init_fbinfo().
If sa1100fb_init_fbinfo is only used by sa1100fb_probe then
annotate sa1100fb_init_fbinfo with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x258): Section mismatch in reference from the function sa1100fb_init_fbinfo() to the (unknown reference) .init.data:(unknown)
The function __devinit sa1100fb_init_fbinfo() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sa1100fb_init_fbinfo then
annotate (unknown) with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x26c): Section mismatch in reference from the function sa1100fb_init_fbinfo() to the (unknown reference) .init.data:(unknown)
The function __devinit sa1100fb_init_fbinfo() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sa1100fb_init_fbinfo then
annotate (unknown) with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x270): Section mismatch in reference from the function sa1100fb_init_fbinfo() to the (unknown reference) .init.data:(unknown)
The function __devinit sa1100fb_init_fbinfo() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sa1100fb_init_fbinfo then
annotate (unknown) with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x278): Section mismatch in reference from the function sa1100fb_init_fbinfo() to the (unknown reference) .init.data:(unknown)
The function __devinit sa1100fb_init_fbinfo() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sa1100fb_init_fbinfo then
annotate (unknown) with a matching annotation.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Obviously this is a typo and although there were no effects observed
it's probably better to fix it.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The MCLK mode defines a factor to divide the clock that is used to
generate the Audio Clock Regeneration packets, MCLK.
The divisor is not used when the CTS value is calculated by HW.
When the value is calculated by SW, it depends on the silicon
revision.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When the MCLK is used to drive the Audio Clock Regeneration packets,
the initialization procedure is to set ACR_CTRL[2] to 0 and then
back again to 1. Also, devices that do not support the MCLK, use
the TMDS clock directly by leaving ACR_CTRL[2] set to 0.
The MLCK clock divisor, mclk_mode, is configured only if MLCK
is used. Such configuration is no longer related to the CTS mode
as in some silicon revisions CTS SW-mode is used along with the MCLK.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Certain OMAP4 revisions (i.e., 4430 ES2.3, 4460, and 4470) use
a pseudo clock (generated from the TMDS clock), MCLK, to drive the
generation of Audio Clock Regeneration packets. Other devices
(i.e., 4430 ES2.[0,2]) use the TMDS clock directly.
This patch adds a new DSS feature for MCLK support. It also rearranges
the omap_dss_features structures to reflect the devices supporting it.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Over time better gamma has been determined and tuned with some
equipment so update the defaults. From subjective point of view
dark shades should be better visible.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
During system suspend, at the time DSS is being suspended, SPI is
already suspended and it's clocks are cut. Because of this trying to
communicate with the LCD controller results in a deadlock.
To fix this, split out LCD programming parts of display enable/disable
functions and perform them from SPI PM callbacks instead when system is
being suspended. If the display is just being enabled/disabled, do it
from DSS callbacks as before.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With AVI infoframe various parameters of video stream such as
aspect ratio, quantization range, videocode etc will be indicated
from source to sink.Thus AVI information needs to be set/accessed
by the middle ware based on the video content.
Thus this parameter is now moved to the ip_data structure.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds support for Innolux AT080TN52 800x600 panel.
Tested with AM3517 based board.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The calculation of required DISPC_FCLK for downscaling is done by multplying the
pixel clock with an integer factor. This isn't true for OMAP4 where the required
clock is calculated using the exact ratio of downscaling done.
Fix this calculation for OMAP4. Also, do a minor clean up of calc_fclk().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The number of dss_feat_id members has increased to a large value, the current
way of assigning a subset of these features (for a particular OMAP) as a mask
is no longer feasible.
Maintain the subset of features supported as lists. Make the function
dss_has_feature() traverse through this list.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that dss is using devm_ functions for allocation in probe functions,
small reordering of the allocations allows us to clean up the probe
functions more.
This patch moves "unmanaged" allocations after the managed ones, and
uses plain returns instead of gotos where possible. This lets us remove
a bunch of goto labels, simplifying the probe's error handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We should handle the allocation here, if only to keep the static
checkers happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This is a resurrection of an old (like 2.4.19) out-of-tree driver for
Intel740 graphics cards and adaptation for recent kernels. The old driver by
Andrey Ulanov is located at: http://sourceforge.net/projects/i740fbdev/files/
This is a new driver based on skeletonfb, using most of the low level HW code
from the old driver. The DDC code is completely new.
The driver was tested on two 8MB cards: Protac AG240D and Diamond Stealth II
G460.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds support for using EDID data on CRT and DVP1 for
initial configuration if viafb_mode or viafb_mode1 are not present.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Samsung EXYNOS SoC such Exynos5 has DP controller and embedded DP
panel can be used. This patch supports DP driver based on Samsung
EXYNOS SoC chip.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
An moled panel driver based MIPI DSI interface. S6E8AX0 means it may
includes many other ldi controllers, for example, S6E8AA0, S6E8AB0, and so
on.
This patch can be modified depending on each panel properites. For
example, second parameter of panel condition register can be changed
depending on ldi controller or amoled type.
[akpm@linux-foundation.org: fix Kconfig syntax error]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Samsung S5PC210 and EXYNOS SoC platform has MIPI-DSI controller and
MIPI-DSI based LCD Panel could be used with it. This patch supports
MIPI-DSI driver based Samsung SoC chip.
LCD panel driver based MIPI-DSI should be registered to MIPI-DSI driver at
machine code and LCD panel driver specific function registered to
mipi_dsim_ddi structure at lcd panel init function called system init. In
the MIPI-DSI driver, find lcd panel driver by using registered lcd panel
name, and then initialize lcd panel driver.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Patch calculates pixel clock period in pico seconds and updates
the same in variable screen information structure. fbset utility
uses this information.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Fix several -Wuninitialized compiler warnings by changing the
order of getting modedb in riva_update_default_var() to set
first the fallback and then the prefered timing.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch fixes the I2C emulation on GPIO ports by enabling it
(software controlled) and disabling the output on a GPIO line before
reading it.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch implementes this mode (viafb_SAMM_ON set and
viafb_dual_fb not set) in a useful way for CRT and DVI devices.
The same content is shown on both devices in different video modes.
The first (primary) resolution must not be bigger than the secondary
one and determines the visible region. The same content is shown
centered on the secondary output.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch fills xres and yres in var which is required when a
temporary var is genereated when viafb_SAMM_ON is set and
viafb_dual_fb is not set. It also removes an obsolete comment.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch sets the correct polarity for the second adapter when
viafb_SAMM_ON is set and viafb_dual_fb is not set. Just one step to
make this mode useful.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds the basic infrastructure and a few stub drivers for
devices that are connected via I2C busses. The infrastructure will
be used to replace and extend the support that is scattered
throughout viafb. The stub drivers are not very useful yet but they
show how the infrastructure works, provide information about the
chips integrated into a system and maybe gather some testers as it
would be very difficult for a single person to get a sane test
environment.
The only thing this actually does is probing the I2C busses which
will hopefully not cause any regressions.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
It includes:
- a compile fix for fsl-diu-fb
- a fix for a suspend/resume issue in atmel_lcdfb
- a fix for a suspend/resume issue in OMAP
- a workaround for a hardware bug to avoid physical damage in OMAP
- a really trivial dead code removal in intelfb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=2uP4
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6
fbdev fixes for 3.3
It includes:
- compile fix for fsl-diu-fb
- fix for a suspend/resume issue in atmel_lcdfb
- fix for a suspend/resume issue in OMAP
- workaround for a hardware bug to avoid physical damage in OMAP
- really trivial dead code removal in intelfb
* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
intelfb: remove some dead code
drivers/video: compile fixes for fsl-diu-fb.c
OMAPDSS: HDMI: PHY burnout fix
OMAP: 4430SDP/Panda: add HDMI HPD gpio
OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
OMAPDSS: remove wrong HDMI HPD muxing
OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
OMAPDSS: use sync versions of pm_runtime_put
This patch converts the drivers in drivers/video/* to use the
module_spi_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Imre Deak <imre.deak@nokia.com>
Cc: Roger Quadros <roger.quadros@nokia.com>
Cc: Steve Sakoman <steve@sakoman.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds video clock running at data under-flow.
It means that the pixel clock is continuously provided
to lcd module, even when under-run occurs.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds alpha value width setting according to
transparency value of each window format, using BLENDCON
register. When alpha value is 8 bits, BLENDCON will set
alpha value width as 8 bits.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch fixes the checkpatch error listed below:
ERROR: trailing statements should be on next line
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Using gpio_request_one can make the code simpler because it can
set the direction and initial value in one shot.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
In au1100fb.c, the probe function now returns -ENODEV on failure.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The USB graphics card driver delays the unregistering of the framebuffer
device to a workqueue, which breaks the userspace visible remove uevent
sequence. Recent userspace tools started to support USB graphics card
hotplug out-of-the-box and rely on proper events sent by the kernel.
The framebuffer device is a direct child of the USB interface which is
removed immediately after the USB .disconnect() callback. But the fb device
in /sys stays around until its final cleanup, at a time where all the parent
devices have been removed already.
To work around that, we remove the sysfs fb device directly in the USB
.disconnect() callback and leave only the cleanup of the internal fb
data to the delayed work.
Before:
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2 (usb)
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0 (usb)
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/graphics/fb0 (graphics)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0 (usb)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2 (usb)
remove /2-1.2:1.0/graphics/fb0 (graphics)
After:
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2 (usb)
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0 (usb)
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/graphics/fb1 (graphics)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/graphics/fb1 (graphics)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0 (usb)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2 (usb)
Cc: stable@vger.kernel.org
Tested-by: Bernie Thompson <bernie@plugable.com>
Acked-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Saves some code, especially useful as the code saved is mostly in the
infrequently tested error paths.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
LCDC functional clock may or may not be derived from CPU/MPU DPLL,
For example,
AM335x => Separate independent DPLL for LCDC
Davinci => Same DPLL as MPU
So, on platforms where LCDC functional clock is not derived from CPU/MPU
PLL it is not required to reset LCDC module as its functional clock does
not change with DVFS.
This patch adds check to do reset only if functional clock changes
between pre and post notifier callbacks with DVFS.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Allow framebuffer to be configured in 16bit mode when panel is wired in
(the default) BGR configuration, and don't claim to support 15bit input
modes, which the LCD controller cannot handle.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
An error was existing in the saving of CONTRAST_CTR register
across suspend/resume.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The goto on the line before means the return is unreachable. The goto
also returns -ENODEV so no changes are needed there.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Fix a compiler errors introduced in:
commit ddd3d90543
Author: Timur Tabi <timur@freescale.com>
drivers/video: fsl-diu-fb: merge all allocated data into one block
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Fix assembler constraint to prevent overeager gcc optimisation
mac_esp: rename irq
mac_scsi: dont enable mac_scsi irq before requesting it
macfb: fix black and white modes
m68k/irq: Remove obsolete IRQ_FLG_* definitions
Fix up trivial conflict in arch/m68k/kernel/process_mm.c as per Geert.
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.
This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.
The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.
The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss doesn't work properly on system suspend. The problem seems to be
the fact that omapdss uses pm_runtime_put() functions when turning off
the hardware, and when system suspend is in process only sync versions
are allowed.
Using non-sync versions normally and sync versions when suspending would
need rather ugly hacks to convey the information of
suspending/not-suspending to different functions. Optimally the driver
wouldn't even need to care about this, and the PM layer would handle
syncing when suspend is in process.
This patch changes all omapdss's pm_runtime_put calls to
pm_runtime_put_sync. This fixes the suspend problem, and probably the
performance penalty of always using sync versions is negligible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit ba02fa37de disabled the
venc driver registration on OMAP4. Since the driver never gets
probed/initialised your get a dereferenceed NULL pointer if you
try to get info from /sys/kernel/debug/omapdss/venc
Return info message about disabled venc if venc_dump_regs() gets called.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Due to changes in struct hdmi_config, the pixel clock has to be obtained
differently.
The pixel clock is needed to calculate the CTS value as defined in the
HDMI specification.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
code and mode parameters are already a part of the ip_data structure
so no need to keep the same parameters again in hdmi global structure.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Change the timing match logic, Instead of the statically mapped method
to get the corresponding timings for a given code and mode, move to a
simpler array indexed method. It will help to scale up to add more
timings when needed.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add the vsync polarity, hsync polarity, interlace to hdmi_video_timings.
Remove the now duplicate structure hdmi_timings.
update the static table structure in HDMI with CEA/VESA code and mode.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
video interface structure is a duplicate structure with parameters which are
already present in ip_data config structure, Thus removing the structure and
modifying corresponding code.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Take fifo merge into use by implementing a rather naive fifo merge
threshold calculation: keep the low threshold always the same, but
increase the high threshold when fifo merge is used.
This should greatly increase the time between pixel data fetches from
SDRAM, as the usable fifo size is much larger. However, it probably
won't help for fifo underflows, as the low threshols is kept the same.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fifo thresholds are calculated using bytes, but the debug print prints
values in buffer units. Change the prints to use bytes to be in line
with the calculations, and also to print in the same units on all OMAPs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add fifo-merge support. This is done mainly in four functions:
mgr_enable/disable and ovl_enable/disable. These are the functions where
overlays are taken into and out of active use.
The process to enable and disable fifo-merge is not simple. We need to
do it in steps, waiting in between for certain settings to be taken into
use, and continuing after that. The reason for this is that fifo-merge
is a common thing for all managers/overlays, and its use must be
synchronized.
As an example, when we disable an overlay, we first set the overlay as
disabled, then wait until the overlay is actually disabled in the HW,
and only after that we may re-configure the fifos, possibly taking
fifo-merge into use.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add mechanism to set/unset the DISPC fifo-merge:
Add new fields to dss_data, fifo_merge and fifo_merge_dirty. These are
similar to the other info/dirty flags in ovl_priv_data and ovl_mgr_data,
but fifo merge is a common attribute to all managers and thus outside
the ovl_mgr_data.
The fifo-merge field is used in the dss_write_regs_common, which handles
writing the register.
dss_apply_fifo_merge() can be used to set/unset the fifo merge field in
the dss_data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add feature flag for fifo merge. OMAP2 doesn't contain fifo merge, later
OMAPs do.
dispc_enable_fifomerge() checks for the flag when called, and gives a
WARN if fifo merge is being enabled when it is not supported.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Alberto Panizzo <alberto@amarulasolutions.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to write new value if the bit mask fields of new value is not
equal to old value. It does not make sense to write new value only when
all the bit_mask bits are zero.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
macfb won't init in black & white modes since fb_alloc_cmap() no longer
works for zero cmap length. Fix this and also clean up a few printk's and
some stylistic inconsistencies.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (175 commits)
module_param: make bool parameters really bool (drivers/video/i810)
Revert "atmel_lcdfb: Adjust HFP calculation so it matches the manual."
OMAPDSS: HDMI: Disable DDC internal pull up
OMAPDSS: HDMI: Move duplicate code from boardfile
OMAPDSS: add OrtusTech COM43H4M10XTC display support
OMAP: DSS2: Support for UMSH-8173MD TFT panel
ASoC: OMAP: HDMI: Move HDMI codec trigger function to generic HDMI driver
OMAPDSS: HDMI: Create function to enable HDMI audio
ASoC: OMAP: HDMI: Correct signature of ASoC functions
ASoC: OMAP: HDMI: Introduce driver data for audio codec
grvga: fix section mismatch warnings
video: s3c-fb: Don't keep device runtime active when open
video: s3c-fb: Hold runtime PM references when touching registers
video: s3c-fb: Take a runtime PM reference when unblanked
video: s3c-fb: Disable runtime PM in error paths from probe
video: s3c-fb: Use s3c_fb_enable() to enable the framebuffer
video: s3c-fb: Make runtime PM functional again
drivers/video: fsl-diu-fb: merge fsl_diu_alloc() into map_video_memory()
drivers/video: fsl-diu-fb: add default platform ops functions
drivers/video: fsl-diu-fb: remove broken reference count enabling the display
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HHrh
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/rustyrussell/linux
Autogenerated GPG tag for Rusty D1ADB8F1: 15EE 8D6C AB0E 7F0C F999 BFCB D920 0E6C D1AD B8F1
* tag 'for-linus' of git://github.com/rustyrussell/linux:
module_param: check that bool parameters really are bool.
intelfbdrv.c: bailearly is an int module_param
paride/pcd: fix bool verbose module parameter.
module_param: make bool parameters really bool (drivers & misc)
module_param: make bool parameters really bool (arch)
module_param: make bool parameters really bool (core code)
kernel/async: remove redundant declaration.
printk: fix unnecessary module_param_name.
lirc_parallel: fix module parameter description.
module_param: avoid bool abuse, add bint for special cases.
module_param: check type correctness for module_param_array
modpost: use linker section to generate table.
modpost: use a table rather than a giant if/else statement.
modules: sysfs - export: taint, coresize, initsize
kernel/params: replace DEBUGP with pr_debug
module: replace DEBUGP with pr_debug
module: struct module_ref should contains long fields
module: Fix performance regression on modules with large symbol tables
module: Add comments describing how the "strmap" logic works
Fix up conflicts in scripts/mod/file2alias.c due to the new linker-
generated table approach to adding __mod_*_device_table entries. The
ARM sa11x0 mcp bus needed to be converted to that too.
pvr2fb special cases its init/exit routines which causes spurious section
mismatches. Set the board_driver array __refdata to silence them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Dan Carpenter points out that it's an int, not a bool:
intelfbdrv.c:818: if (bailearly == 1)
intelfbdrv.c:828: if (bailearly == 2)
intelfbdrv.c:836: if (bailearly == 3)
intelfbdrv.c:842: if (bailearly == 4)
intelfbdrv.c:851: if (bailearly == 5)
intelfbdrv.c:859: if (bailearly == 6)
intelfbdrv.c:866: bailearly > 6 ? bailearly - 6 : 0);
intelfbdrv.c:874: if (bailearly == 18)
intelfbdrv.c:886: if (bailearly == 19)
intelfbdrv.c:893: if (bailearly == 20)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This reverts commit 5d910426a6.
Nicolas Ferre <nicolas.ferre@atmel.com> wrote:
"Unfortunately this is not true for all the SoC that embed the
atmel_lcdfb... So I may need to rework this patch but it is certainly
not applicable in the current form."
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Andrew elucidates:
- First installmeant of MM. We have a HUGE number of MM patches this
time. It's crazy.
- MAINTAINERS updates
- backlight updates
- leds
- checkpatch updates
- misc ELF stuff
- rtc updates
- reiserfs
- procfs
- some misc other bits
* akpm: (124 commits)
user namespace: make signal.c respect user namespaces
workqueue: make alloc_workqueue() take printf fmt and args for name
procfs: add hidepid= and gid= mount options
procfs: parse mount options
procfs: introduce the /proc/<pid>/map_files/ directory
procfs: make proc_get_link to use dentry instead of inode
signal: add block_sigmask() for adding sigmask to current->blocked
sparc: make SA_NOMASK a synonym of SA_NODEFER
reiserfs: don't lock root inode searching
reiserfs: don't lock journal_init()
reiserfs: delay reiserfs lock until journal initialization
reiserfs: delete comments referring to the BKL
drivers/rtc/interface.c: fix alarm rollover when day or month is out-of-range
drivers/rtc/rtc-twl.c: add DT support for RTC inside twl4030/twl6030
drivers/rtc/: remove redundant spi driver bus initialization
drivers/rtc/rtc-jz4740.c: make jz4740_rtc_driver static
drivers/rtc/rtc-mc13xxx.c: make mc13xxx_rtc_idtable static
rtc: convert drivers/rtc/* to use module_platform_driver()
drivers/rtc/rtc-wm831x.c: convert to devm_kzalloc()
drivers/rtc/rtc-wm831x.c: remove unused period IRQ handler
...
Should be no functional changes, mainly a reorganisation to support future
work.
[akpm@linux-foundation.org: fix CONFIG_PM=n build]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Saves some error handling code and eliminates a class of leaks.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The usage of simple_strtoul() or strict_strtoul() is not preferred. Thus,
kstrtoul should be used.
This patch also fixes checkpatch error as follows:
ERROR: space required after that ',' (ctx:VxV)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
module.h is included twice.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch supports regulator power control in the driver. Current ld9040
driver was controlled power on/off sequence by callback function in the
board file. But, by doing this, there's no need to register lcd power
on/off callback function in the board file.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the drivers in drivers/video/backlight/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> [ep93xx_bl.c]
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support for the Avionic Design Xanthos backlight device got added in
commit 3b96ea9ef8 ("backlight: Add support for the Avionic Design Xanthos
backlight device."). That support depends on ARCH_PXA_ADX. The code that
should have provided that Kconfig symbol never got submitted. It has
never been possible to even build this driver. Remove it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'stable/for-linus-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (37 commits)
xen/pciback: Expand the warning message to include domain id.
xen/pciback: Fix "device has been assigned to X domain!" warning
xen/pciback: Move the PCI_DEV_FLAGS_ASSIGNED ops to the "[un|]bind"
xen/xenbus: don't reimplement kvasprintf via a fixed size buffer
xenbus: maximum buffer size is XENSTORE_PAYLOAD_MAX
xen/xenbus: Reject replies with payload > XENSTORE_PAYLOAD_MAX.
Xen: consolidate and simplify struct xenbus_driver instantiation
xen-gntalloc: introduce missing kfree
xen/xenbus: Fix compile error - missing header for xen_initial_domain()
xen/netback: Enable netback on HVM guests
xen/grant-table: Support mappings required by blkback
xenbus: Use grant-table wrapper functions
xenbus: Support HVM backends
xen/xenbus-frontend: Fix compile error with randconfig
xen/xenbus-frontend: Make error message more clear
xen/privcmd: Remove unused support for arch specific privcmp mmap
xen: Add xenbus_backend device
xen: Add xenbus device driver
xen: Add privcmd device driver
xen/gntalloc: fix reference counts on multi-page mappings
...
Another simple series related to clock management, this time only for
imx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=czKE
-----END PGP SIGNATURE-----
Merge tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
clock management changes for i.MX
Another simple series related to clock management, this time only for
imx.
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: select HAVE_CLK_PREPARE for clock
clk: add config option HAVE_CLK_PREPARE into Kconfig
ASoC: mxs-saif: convert to clk_prepare/clk_unprepare
video: mxsfb: convert to clk_prepare/clk_unprepare
serial: mxs-auart: convert to clk_prepare/clk_unprepare
net: flexcan: convert to clk_prepare/clk_unprepare
mtd: gpmi-lib: convert to clk_prepare/clk_unprepare
mmc: mxs-mmc: convert to clk_prepare/clk_unprepare
dma: mxs-dma: convert to clk_prepare/clk_unprepare
net: fec: add clk_prepare/clk_unprepare
ARM: mxs: convert platform code to clk_prepare/clk_unprepare
clk: add helper functions clk_prepare_enable and clk_disable_unprepare
Fix up trivial conflicts in drivers/net/ethernet/freescale/fec.c due to
commit 0ebafefcaa ("net: fec: add clk_prepare/clk_unprepare") clashing
trivially with commit e163cc97f9 ("net/fec: fix the .remove code").
* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (466 commits)
net/hyperv: Add support for jumbo frame up to 64KB
net/hyperv: Add NETVSP protocol version negotiation
net/hyperv: Remove unnecessary kmap_atomic in netvsc driver
staging/rtl8192e: Register against lib80211
staging/rtl8192e: Convert to lib80211_crypt_info
staging/rtl8192e: Convert to lib80211_crypt_data and lib80211_crypt_ops
staging/rtl8192e: Add lib80211.h to rtllib.h
staging/mei: add watchdog device registration wrappers
drm/omap: GEM, deal with cache
staging: vt6656: int.c, int.h: Change return of function to void
staging: usbip: removed unused definitions from header
staging: usbip: removed dead code from receive function
staging:iio: Drop {mark,unmark}_in_use callbacks
staging:iio: Drop buffer mark_param_change callback
staging:iio: Drop the unused buffer enable() and is_enabled() callbacks
staging:iio: Drop buffer busy flag
staging:iio: Make sure a device is only opened once at a time
staging:iio: Disallow modifying buffer size when buffer is enabled
staging:iio: Disallow changing scan elements in all buffered modes
staging:iio: Use iio_buffer_enabled instead of open coding it
...
Fix up conflict in drivers/staging/iio/adc/ad799x_core.c (removal of
module_init due to using module_i2c_driver() helper, next to removal of
MODULE_ALIAS due to using MODULE_DEVICE_TABLE instead).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
* 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
sound: aaci: Enable module alias autogeneration for AMBA drivers
watchdog: sp805: Enable module alias autogeneration for AMBA drivers
fbdev: amba: Enable module alias autogeneration for AMBA drivers
serial: pl011: Enable module alias autogeneration for AMBA drivers
serial: pl010: Enable module alias autogeneration for AMBA drivers
spi: pl022: Enable module alias autogeneration for AMBA drivers
rtc: pl031: Enable module alias autogeneration for AMBA drivers
rtc: pl030: Enable module alias autogeneration for AMBA drivers
mmc: mmci: Enable module alias autogeneration for AMBA drivers
input: ambakmi: Enable module alias autogeneration for AMBA drivers
gpio: pl061: Enable module alias autogeneration for AMBA drivers
dmaengine: pl330: Enable module alias autogeneration for AMBA drivers
dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers
hwrng: nomadik: Enable module alias autogeneration for AMBA drivers
ARM: amba: Auto-generate AMBA driver module aliases during modpost
ARM: amba: Move definition of struct amba_id to mod_devicetable.h
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (185 commits)
powerpc: fix compile error with 85xx/p1010rdb.c
powerpc: fix compile error with 85xx/p1023_rds.c
powerpc/fsl: add MSI support for the Freescale hypervisor
arch/powerpc/sysdev/fsl_rmu.c: introduce missing kfree
powerpc/fsl: Add support for Integrated Flash Controller
powerpc/fsl: update compatiable on fsl 16550 uart nodes
powerpc/85xx: fix PCI and localbus properties in p1022ds.dts
powerpc/85xx: re-enable ePAPR byte channel driver in corenet32_smp_defconfig
powerpc/fsl: Update defconfigs to enable some standard FSL HW features
powerpc: Add TBI PHY node to first MDIO bus
sbc834x: put full compat string in board match check
powerpc/fsl-pci: Allow 64-bit PCIe devices to DMA to any memory address
powerpc: Fix unpaired probe_hcall_entry and probe_hcall_exit
offb: Fix setting of the pseudo-palette for >8bpp
offb: Add palette hack for qemu "standard vga" framebuffer
offb: Fix bug in calculating requested vram size
powerpc/boot: Change the WARN to INFO for boot wrapper overlap message
powerpc/44x: Fix build error on currituck platform
powerpc/boot: Change the load address for the wrapper to fit the kernel
powerpc/44x: Enable CRASH_DUMP for 440x
...
Fix up a trivial conflict in arch/powerpc/include/asm/cputime.h due to
the additional sparse-checking code for cputime_t.
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dd data for the OrtusTech COM43H4M10XTC display to the
generic_dpi_panel driver.
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds support for Microtip Technologies' UMSH-8173MD 800x480
RGB TFT panel. Tested with an OMAP3 board.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[tomi.valkeinen@ti.com: changed the panel name string]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function hdmi_audio_trigger is a callback used by ASoC to stop/start
HDMI audio. Also, it does not perform IP-specific configuration directly.
Hence, it should be placed in the general portion of the HDMI driver,
along with the other ASoC callbacks.
Also, make this function static.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to separate clearly IP-specific code from general DSS code,
a function for OMAP4 audio enable is created. This function is
included in the HDMI IP ops to align with the current implementation
of the DSS HDMI driver. This function is to be used by the ASoC
HDMI audio codec.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These functions require access to IP-secific data. However, it is not possible
to pass such data as a function argument as such functions have a specific
signature specified by ASoC. Instead, they will have access to the IP-specific
data by calling snd_soc_codec_get_drvdata. The codec driver data is set
at probe time.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Under the new DSS architecture for HDMI, there is a clear separation
between general DSS code and HDMI IP-specific data. Functions
that require access to the HDMI driver IP-specific data receive an
hdmi_ip_data structure. The ASoC codec require access to such
IP-specific data. Then, instead of accessing it directly, it will be
passed as codec driver data. This also helps to have a clear separation
between DSS and ASoC portions of the code.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The 'name', 'owner', and 'mod_name' members are redundant with the
identically named fields in the 'driver' sub-structure. Rather than
switching each instance to specify these fields explicitly, introduce
a macro to simplify this.
Eliminate further redundancy by allowing the drvname argument to
DEFINE_XENBUS_DRIVER() to be blank (in which case the first entry from
the ID table will be used for .driver.name).
Also eliminate the questionable xenbus_register_{back,front}end()
wrappers - their sole remaining purpose was the checking of the
'owner' field, proper setting of which shouldn't be an issue anymore
when the macro gets used.
v2: Restore DRV_NAME for the driver name in xen-pciback.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Fix following section mismatch warnings:
WARNING: drivers/video/built-in.o(.devinit.text+0x110): Section mismatch in reference from the function grvga_probe() to the function .init.text:grvga_parse_custom()
The function __devinit grvga_probe() references
a function __init grvga_parse_custom().
If grvga_parse_custom is only used by grvga_probe then
annotate grvga_parse_custom with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x1f8): Section mismatch in reference from the function grvga_probe() to the variable .init.data:grvga_fix
The function __devinit grvga_probe() references
a variable __initdata grvga_fix.
If grvga_fix is only used by grvga_probe then
annotate grvga_fix with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x204): Section mismatch in reference from the function grvga_probe() to the variable .init.data:grvga_fix
The function __devinit grvga_probe() references
a variable __initdata grvga_fix.
If grvga_fix is only used by grvga_probe then
annotate grvga_fix with a matching annotation.
grvga_fix is used in a function annotated __devinit - so
match this using a __devinitdata annotation on grvga_fix.
grvga_parse_custom() is used in a function annotated
__devinit - so match this by annotating grvga_parse_custom()
with __devinit too.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Allow the controller to be runtime suspended when the screen is blanked
by not taking a runtime reference while the device is open. This allows
greater system wide power savings when used with a standard application
layer and ensures that the screen does not blank unless requested.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Take a runtime PM reference whenever updating registers in preparation
for suspending the device when the framebuffer is blanked.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
When the framebuffer is unblanked hold a runtime PM reference. This
prevents us powering down when userspace has left an image on the
framebuffer and prepares the way for being able to power down the hardware
when an application still has the device open.
Since we now hold a runtime PM reference whenever the display is unblanked
there is no need for the runtime power management to disable and enable
the display, and doing so would lead to runtime PM trying to recurse into
itself when called from the blanking code, so split the runtime PM into
separate functions which only deal with the clocks. The PM core will
runtime resume the device prior to system suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The s3c-fb driver has a function called s3c_fb_enable() which turns on
and off the physical output. However it is only actually used in paths
which disable the screen, the enabling just writes to the register. Make
the code less confusing by ensuring that the enable also goes through
the same path.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The change in "video: s3c-fb: modify runtime pm functions" (commit
35784b) renders the runtime power management for the device completely
ineffectual as while it leaves runtime power management notionally
enabled a runtime power reference is held for the entire time the device
is registered meaning it will never actually do anything.
A further issue is introduced as runtime power management is added
during the system suspend path which is not something which drivers are
supposed to do and would interact poorly if there were any operations
done in the runtime power management callbacks.
While this does make things simpler (the main motivation for the
original change) it will not only cause us to use more power in the
framebuffer controller but will also prevent us entering lower power
domain and SoC wide states as we can never power down the domain
containing the device. Since neither of these things is desirable
revert the change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Functions fsl_diu_alloc() and fsl_diu_free() were only being called by
map_video_memory() and unmap_video_memory(), respectively.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The DIU driver requires some platform-specific functions to be defined,
but two them can be optional because most platforms implement them the
same way. Functions set_gamma_table() and get_pixel_format() are only
needed because of quirks in the Freescale MPC8610 HPCD reference board.
For other boards, a generic implementation works, so we shouldn't
require the platform code to define them.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The functions enable_lcdc() and disable_lcdc() used the variable fb_enable
to keep a reference count of when the display is enabled, but the code is
broken. The display is always disabled when disable_lcdc(), and it is
always enabled when enable_lcdc() is called, regardless of the value of
fb_enable. Obviously, we don't need to keep a reference count, so just
remove the variable.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The DIU uses system RAM for the framebuffer, so FBINFO_VIRTFB should be set.
Since the framebuffer is in system RAM, it can be read from more quickly
than written to, so FBINFO_READS_FAST should be set.
We can also set FBINFO_PARTIAL_PAN_OK for the same reasons.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Function init_fbinfo() is called only from install_fb(), and it's only a few
lines long. Plus, it ignores the return code from fb_alloc_cmap(). Merge
its contents into install_fb() and handle errors properly.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
When using a >8bpp framebuffer, offb advertises truecolor, not directcolor,
and doesn't touch the color map even if it has a corresponding access method
for the real hardware.
Thus it needs to set the pseudo-palette with all 3 components of the color,
like other truecolor framebuffers, not with copies of the color index like
a directcolor framebuffer would do.
This went unnoticed for a long time because it's pretty hard to get offb
to kick in with anything but 8bpp (old BootX under MacOS will do that and
qemu does it).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@kernel.org
We rename the mach64 hack to "simple" since that's also applicable
to anything using VGA-style DAC IO ports (set to 8-bit DAC) and we
use it for qemu vga.
Note that this is keyed on a device-tree "compatible" property that
is currently only set by an upcoming version of SLOF when using the
qemu "pseries" platform. This is on purpose as other qemu ppc platforms
using OpenBIOS aren't properly setting the DAC to 8-bit at the time of
the writing of this patch.
We can fix OpenBIOS later to do that and add the required property, in
which case it will be matched by this change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We used to try to request 8 times more vram than needed, which would
fail if the card has a too small BAR (observed with qemu & kvm).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@kernel.org
Clock requirements for scaling in OMAP2, OMAP3 and OMAP4 are different. In
OMAP2 and OMAP3 the required clock rate is a function of pixel clock, vertical
downscale ratio and horizontal downscale ratio whereas in OMAP4 it is a
function of pixel clock and horizontal downscale ratio only. Selection of 3-tap
vs 5-tap coefficients depends on clock rate line buffer width in OMAP3 whereas
in OMAP4 it is independent of clock rate and line buffer width. In OMAP2 3-tap
for vertical and 5-tap for horizontal scaling is used. In OMAP4 5-tap is used
both for horizontal and vertical scaling for better performance. Also, the
number and width of line buffers differs in OMAP3 and OMAP4.
So, clock functions have been fined tuned for OMAP3 and support has been added
added for OMAP4. This code has been tested on OMAP2, OMAP3 and OMAP4, and
scaling issues due to clock errors have been resolved.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The FIR coefficients present in kernel are being updated to new coefficients
consisting of 24 coefficient tables, with 12 each for 3 tap and 5 tap scenario,
which are chosen on the basis of DISPC up/downsampling filters M value. M is
the inverse of low pass cut off frequency of the sampling filter. For vertical
scaling 3 tap or 5 tap tables are used based on the clock rate and width of
the line buffer whereas in OMAP2 3 tap is always used. For horizontal scaling
however 5 tap tables are always used.
New coefficients and the corresponding logic have been tested on OMAP2, OMAP3
and OMAP4. Horizontal and vertical scaling worked fine except for some 3 tap
vs 5 tap issue during vertical upscaling and clock failing issues which is
acknowledged in the next patch. Vertical upscaling was found to perform better
under 5 taps. The 24 coefficient tables have been moved to another file
dispc_coefs.c for proper maintainance.
This code is written based on code written by Lajos Molnar <lajos@ti.com> in
Android Kernel for scaling. Lajos Molnar <lajos@ti.com> had fine tuned the FIR
coefficient selection process and reduced outliness and blockiness around
images when upscaling more than 2 times.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
extra_info_update_ongoing() goes through all overlays, but doesn't check
if the overlay is connected to a manager. This leads to a crash whenever
an overlay has been detached.
Add a check to skip the non-connected overlays.
Reported-by: Rob Clark <rob@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make PICODLP driver on OMAP2_DSS_DPI since it is the display interface it uses.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The display state parameter of omap_dss_device struct is not being set correctly
in the panel driver NEC panel driver panel-nec-nl8048hl11-01b.c. Set the correct
states in the panel's enable/disable/suspend/resume functions.
CC: Erik Gilling <konkers@android.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The clock names of DSI_PLL_HSDIV_DISPC and DSI_PLL_HSDIV_DSI was made
dynamic based on the current value of DISPC and DSI FCLK sources. This
doesn't need to be done since we are just interested in the clock names,
and not the current clock sources for DISPC and DSI FCLKs.
Use only the generic and omap specific names for the DSI PLL's HSDIV
clocks.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions dss_ovl_simple_check() and dss_mgr_simple_check() are not
really part of the apply mechanism, and can be moved to overlay.c and
manager.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dispc's error handler tries to disable all outputs when OCP_ERR
happens. However, the code doesn't check if there actually is a display
on each particular output, nor if there's a driver for the display. This
may lead to NULL pointer reference.
Signed-off-by: Rob Clark <rob@ti.com>
[tomi.valkeinen@ti.com: added patch description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch converts the drivers in drivers/video/omap/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Laurent Gonzalez <palmte.linux@free.fr>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These symbols are not used outside it's driver so no need to
make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions dss_ovl_check, dss_mgr_check_zorder, dss_mgr_check in
apply.c are not really part of the apply mechanism, and can be moved to
overlay.c and manager.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Don't use Amstrad Delta custom I/O functions any longer, use GPIO API
instead.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit fb21c2f428 ("fbdev: Add FOURCC-based format configuration API")
modified the layout of the fb_var_screeninfo structure. Remove zero
fields from the static initializers in the matroxfb driver accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Add memory size detection for Virge/VX and small delay in mode setting (same
as in X.org driver) to fix blank screen problem.
Also adjust DTPC position to fix garbled screen in some modes (tested that
this adjustment does not break other cards - at least Trio32, Trio64V+,
Trio64V2/DX, Virge, Virge/DX).
Tested on ELSA Winner 2000AVI/3D.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The driver should be registered with mxsfb_driver, not with mxsfb_devtype.
This caused obvious null pointer dereference and crash.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Huang Shijie <b32955@freescale.com>
Acked-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The driver says "module_param(ddc3, bool, 0);". But it's not a used
as a bool, it's used as a count.
Make it a bool.
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch converts the drivers in drivers/video/pnx4008/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Grigory Tolstolytkin <gtolstolytkin@ru.mvista.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch converts mbxfb to use the module_platform_driver() macro
which makes the code smaller and a bit simpler.
Cc: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This API will be used to support YUV frame buffer formats in a standard
way.
Last but not least, create a much needed fbdev API documentation and
document the format setting APIs.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
"machine_data" is too long and clunky, and the "machine" part doesn't make
much sense, anyway.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Shadow registers should be protectd whenever the registers are
updated. Shadow registers are updated after SHADOWCON shadow
register is cleared.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Runtime suspend and runtime resume are modified in order to
reduce the complexity and improve the usability of runtime pm.
After probe function, s3c-fb driver is not suspended until
suspend or remove is called.
The scheme is changed as follows:
runtime_get is only called in probe and resume.
runtime_put is only called in remove and suspend.
open/close cannot call the runtime_get/put.
Also, runtime_susepnd/resume are just called by runtime pm,
not doing suspend/resume routine any longer. This is because
open/close cannot call the runtime_get/put; the suspend/resume
routine in runtime_suspend/resume were previously used when
open and close were called.
The name of s3c-fb dev_pm_ops is changed from s3cfb_pm_ops to
s3c_fb_pm_ops in order to use more consistent naming.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The Freescale DIU driver allocates multiple blocks of memory, including
multiple DMA buffers. Merge all of these blocks into one data structure.
Specifically:
1) struct fsl_diu_data now contains everything that needs to be allocated,
except for the framebuffers themselves. DMA'able objects are aligned correctly
within the structure.
2) struct diu_addr is no longer needed, because we don't have to manage
multiple blocks of DMA memory.
3) Since there's no diu_addr any more, macro DMA_ADDR is used to calculate
the DMA address of any field in fsl_diu_data.
4) Functions allocate_buf() and free_buf() are no longer needed, because we
now assume that dma_alloc_coherent() will allocate a page-aligned block,
and everything is properly aligned with fsl_diu_data already, so we no longer
need to align any memory blocks ourselves.
5) The "dummy" area descriptor is now defined separately from the other
five ADs, so NUM_AOIS (previously called FSL_AOI_NUM) is now set to five
instead of six. Previously, all six were combined together to avoid a
separate call to allocate_buf() just for the dummy AD.
6) framebuffer_alloc() and framebuffer_release() are no longer used. The
framebuffer is initialized manually.
7) Error handling is simplified since there's only one memory buffer
allocated.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch set missing bitmask of enabled hardware window which
should be checked whenever the hardware window is enabled.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This resolves the conflict in the
drivers/staging/iio/industrialio-core.c file due to two different
changes made to resolve the same problem.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The IPU internally works on 32bit colors. It can arbitrarily map
between pixel formats and internal representation and also between
internal representation and the physical connection to the display.
The driver used to change the mapping between internal representation
and display connection depending on the user selected bpp which is
wrong. Instead, the mapping is specified by the hardware, so an
additional field in platform data is added to describe the connection
between i.MX and the display. The default for this field is RGB666
which seems to be the only configuration which works without this
patch, so I assumed that all in Kernel boards are connected this
way.
This patch has been tested on a RGB666 connected display and a
RGB888 connected display in both 16bpp and 32bpp modes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
SGI IP22/IP28 machines have GIO busses for adding graphics and other
extension cards. This patch adds support for GIO driver/device
handling and converts the newport console driver to a GIO driver.
[ralf@linux-mips.org: Fixed build error caused by the modules.h -> export.h
changes.]
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
To: linux-fbdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2886/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These 3 boards are very similar; with this patch a single kernel image
which runs on all three can be built.
Tested on DB1500 and DB1100.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2872/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add basic support for the Au1300 variant(s):
- New GPIO/Interrupt controller
- DBDMA ids
- USB setup
- MMC support
- enable various PSC drivers
- detection code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the checkpatch errors listed below:
ERROR: do not initialise statics to 0 or NULL
WARNING: Use #include <linux/io.h> instead of <asm/io.h>
WARNING: braces {} are not necessary for single statement blocks
WARNING: braces {} are not necessary for any arm of this statement
WARNING: static char array declaration should probably be static const char
WARNING: line over 80 characters
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The s3c-fb driver has separate runtime and system PM functions but the
implementations are identical so far as I can tell so unify them for
simplicity.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch converts the drivers in drivers/video/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexey Charkov <alchark@gmail.com>
Acked-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Use framebuffer_alloc() instead of static fb_info and currentpar variables.
Also sanitize the error path and cleanup code (e.g. missing free_irq()).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Kuninori Morimoto