The in-band data are copied twice: before ECC correction and after the
ECC engine has fixed all the fixable bitflips.
Drop the useless memcpy_fromio operation by passing a NULL pointer when
calling sunxi_nfc_read_buf().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The sunxi_nfc_hw_ecc_read/write_chunk() functions try to avoid changing
the column address if unnecessary, but the logic to determine whether it's
necessary or not is currently wrong: it adds the ecc->bytes value to the
current offset where it should actually add ecc->size.
Fixes: 913821bdd2 ("mtd: nand: sunxi: introduce sunxi_nfc_hw_ecc_read/write_chunk()")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Just like other NAND controllers, the NAND READID command only works
in 8bit mode for all versions of BRCMNAND controller.
This patch forces 8bit mode for each NAND CS in brcmnand_init_cs()
before doing nand_scan_ident() to ensure that BRCMNAND controller
is in 8bit mode when NAND READID command is issued.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use enum instead of magic numbers for CFG and CFG_EXT bitfields.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Anup Patel <anup.patel@broadcom.com>
This patch adds support for 4-bit ECC BCH4 for the SPEAr600 SoC. This can
be used by boards equipped with a NAND chip that requires 4-bit ECC
strength. The SPEAr600 HW ECC only supports 1-bit ECC strength.
To enable SW BCH4, you need to specify this in your nand controller
DT node:
nand-ecc-mode = "soft_bch";
nand-ecc-strength = <4>;
nand-ecc-step-size = <512>;
Tested on a custom SPEAr600 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
[Brian: tweaked the comments a bit]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If nand_wait_ready() times out, this is silently ignored, and its
caller will then proceed to read from/write to the chip before it is
ready. This can potentially result in corruption with no indication as
to why.
While a 20ms timeout seems like it should be plenty enough, certain
behaviour can cause it to timeout much earlier than expected. The
situation which prompted this change was that CPU 0, which is
responsible for updating jiffies, was holding interrupts disabled
for a fairly long time while writing to the console during a printk,
causing several jiffies updates to be delayed. If CPU 1 happens to
enter the timeout loop in nand_wait_ready() just before CPU 0 re-
enables interrupts and updates jiffies, CPU 1 will immediately time
out when the delayed jiffies updates are made. The result of this is
that nand_wait_ready() actually waits less time than the NAND chip
would normally take to be ready, and then read_page() proceeds to
read out bad data from the chip.
The situation described above may seem unlikely, but in fact it can be
reproduced almost every boot on the MIPS Creator Ci20.
Therefore, this patch increases the timeout to 400ms. This should be
enough to cover cases where jiffies updates get delayed. In nand_wait()
the timeout was previously chosen based on whether erasing or
programming. This is changed to be 400ms unconditionally as well to
avoid similar problems there. nand_wait() is also slightly refactored
to be consistent with nand_wait{,_status}_ready(). These changes should
have no effect during normal operation.
Debugging this was made more difficult by the misleading comment above
nand_wait_ready() stating "The timeout is caught later" - no timeout was
ever reported, leading me away from the real source of the problem.
Therefore, a pr_warn() is added when a timeout does occur so that it is
easier to pinpoint similar problems in future.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Reviewed-by: Niklas Cassel <niklas.cassel@axis.com>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
With the previous modifications, lots of pxa3xx specific definitions can
be removed.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Rework the pxa3xx_nand driver to allow using functions exported by the
nand framework to detect the flash and the timings. Then setup the
timings using the helpers previously added.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add helpers to setup the timings in the pxa3xx driver. These helpers
allow to either make use of the nand framework nand_sdr_timings or the
pxa3xx specific pxa3xx_nand_host, for compatibility reasons.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Using readsl() result in a build error on i386. Fix this by using
ioread32_rep() instead, to allow compile testing the pxa3xx nand driver
on other architectures later.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If common clock framework is configured, the driver generates a warning,
which is fixed by this change:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc2+ #206
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc32xx_nand_probe+0x208/0x248)
[<>] (lpc32xx_nand_probe) from [<>] (platform_drv_probe+0x50/0xa0)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
[<>] (__platform_driver_register) from [<>] (lpc32xx_nand_driver_init+0x18/0x20)
[<>] (lpc32xx_nand_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If common clock framework is configured, the driver generates a warning,
which is fixed by this change:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc2+ #201
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc32xx_nand_probe+0x290/0x568)
[<>] (lpc32xx_nand_probe) from [<>] (platform_drv_probe+0x50/0xa0)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
[<>] (__platform_driver_register) from [<>] (lpc32xx_nand_driver_init+0x18/0x20)
[<>] (lpc32xx_nand_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The old PM model is deprecated. This is equivalent.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
mtd_{suspend,resume}() get called from mtdcore in a class suspend/resume
callback. We don't need to call them again here. In practice, this would
actually work OK, as nand_base actually handles nesting OK -- it just
might print warnings.
Untested, but there are few (no?) users of PM for this driver AFAIK.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
The ->read_xxx() methods are all passed the page number the NAND controller
is supposed to read, but ->write_xxx() do not have such a parameter.
This is a problem if we want to properly implement data
scrambling/randomization in order to mitigate MLC sensibility to repeated
pattern: to prevent bitflips in adjacent pages in the same block we need
to avoid repeating the same pattern at the same offset in those pages,
hence the randomizer/scrambler engine need to be passed the page value
in order to adapt its seed accordingly.
Moreover, adding the page parameter to the ->write_xxx() methods add some
consistency to the current API.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Josh Wu <josh.wu@atmel.com>
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Huang Shijie <shijie.huang@arm.com>
CC: Stefan Agner <stefan@agner.ch>
CC: devel@driverdev.osuosl.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where mtd parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Make sure the device structure is properly shown in sysfs by properly
filling in dev.parent.
While at it, make use of the default owner and name values set by
mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner and name set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner and name are automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Owner is automatically set by mtdcore. Make use of that.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Boris BREZILLON