Just pass VIDIOC_S_PARM and VIDIOC_G_PARM down to host drivers. So far no
special handling in soc-camera core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes "buswidth" struct member, and sets the default buswidth
to the natively supported 10 bit. You can select 8 bit buswidth by new flag.
This patch also modify ap325rxa/migor setup.c
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add supports for the radio system on the Intel Russellville board.
It's a In-Vehicle Infotainment board with a radio tuner and DSP.
This umbrella driver has the DSP and tuner as V4L2 subdevs and calls them
when needed.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initial support for the SAA7706H Car Radio DSP.
It is a I2C device and currently the mute control is supported.
When the device is unmuted it is brought out of reset and initiated using
the proposed intialisation sequence.
When muted the DSP is brought into reset state.
[akpm@linux-foundation.org: include delay.h]
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: Douglas Schilling Landgraf <dougsland@gmail.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fix Video/Sound support "Leadtek winfast tv usbii deluxe".
Now, it is working Stereo, IR, Radio, TV, Svideo and Composite.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change attempts to fix the ivtv tinny audio problem by keeping digitizer
to encoder audio clocks running, while disabling the video clocks as needed to
avoid unpredictable PCI bus hangs.
To accomplish this, for the cx25840 module enabling of audio streaming had
to be separated from enabling video streaming, requiring an additional
v4l2_subdev_audio_op and calls to this new op in the pvrusb2 and ivtv drivers.
The cx231xx and cx23885 driver use the cx25840 module for affecting only
video on s_stream calls, so those drivers needed no change.
The CX23418 hardware does not exhibit either the tinny audio problem nor the PCI
bus hang, so the cx18 driver did not need corresponding changes.
CX2341[56] based cards that are not using the CX2584x family of chips
do not seem to be affected by the tinny audio problem, and this change should
not affect how they are configured. It will delay their first capture by
starting by another 300 msec though.
Many thanks go to Argus <pthorn-ivtvd@styx2002.no-ip.org> and
Martin Dauskardt <martin.dauskardt@gmx.de> whose persistent testing and
investigation of this problem will hopefully fix this problem once and for all
for many ivtv users.
Reported-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Reported-by: Argus <pthorn-ivtvd@styx2002.no-ip.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When preparing the linux-next patches, I got those errors:
include/media/ir-core.h:29: warning: left shift count >= width of type
In file included from include/media/ir-common.h:29,
from drivers/media/video/ir-kbd-i2c.c:50:
drivers/media/video/ir-kbd-i2c.c: In function ‘ir_probe’:
drivers/media/video/ir-kbd-i2c.c:324: warning: left shift count >= width of type
Unfortunately, enum is 32 bits on i386. As we define IR_TYPE_OTHER as 1<<63,
it won't work on non 64 bits arch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds an structure to ir_input_register to contain IR device characteristics,
like supported protocols and a callback to handle protocol event changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add sysfs skeleton to export remote controller information via
/sys/class/irrcv.
For now, the code doesn't do much. It just exports an attribute that
is meant to report and control the IR protocol used by the keytable.
However, the callbacks for this new attribute weren't set yet.
Also, it lacks symlinks to the used event interface.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It has been experimentally found out, that the sensor only supports up to
512x384 video output and also has some restrictions on minimum scale. We
disable non-working size ranges until, maybe, someone finds out how to properly
set them up. Also add cropping support, an auto white balance control, platform
data to specify master clock frequency and polarity of the IOCTL pin.
create mode 100644 include/media/rj54n1cb0c.h
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert soc-camera core and all soc-camera drivers to the new mediabus
API. This also takes soc-camera client drivers one step closer to also be
usable with generic v4l2-subdev host drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Video subdevices, like cameras, decoders, connect to video bridges over
specialised busses. Data is being transferred over these busses in various
formats, which only loosely correspond to fourcc codes, describing how video
data is stored in RAM. This is not a one-to-one correspondence, therefore we
cannot use fourcc codes to configure subdevice output data formats. This patch
adds codes for several such on-the-bus formats and an API, similar to the
familiar .s_fmt(), .g_fmt(), .try_fmt(), .enum_fmt() API for configuring those
codes. After all users of the old API in struct v4l2_subdev_video_ops are
converted, it will be removed. Also add helper routines to support generic
pass-through mode for the soc-camera framework.
create mode 100644 drivers/media/video/soc_mediabus.c
create mode 100644 include/media/soc_mediabus.h
create mode 100644 include/media/v4l2-mediabus.h
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After this change drivers can be further extended to not fail, if they don't
get platform data, but to use defaults.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Up to now, if a client driver needed platform data apart from those contained
in struct soc_camera_link, it had to embed the struct into its own object. This
makes the use of such a driver in configurations other than soc-camera
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce new v4l2-subdev sensor operations, move .enum_framesizes() and
.enum_frameintervals() methods to it, add a new .g_skip_top_lines() method
and switch soc-camera to use it instead of .y_skip_top soc_camera_device
member, which can now be removed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a helper function to get description of a digital
video preset added by the video timing API. This will be useful for drivers
implementing the above API.
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We'll need to register a sysfs class for the IR devices. As such, the better
is to have the input_register_device()/input_unregister_device() inside
the ir register/unregister functions.
Also, solves a naming problem with V4L ir_input_init() function, that were,
in fact, registering a device.
While here, do a few cleanups at budget-ci IR logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, ir_input_free does more than just freeing the keytab. Better to
rename it as ir_input_unregister.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move non-V4L specific stuff from ir-functions ir_input_init() into
a new function to register ir devices: ir_input_register().
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Split the ir-common into two separate modules:
- ir-core: it is the IR-independent functions;
- ir-common: has the common part used by V4L drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds the above APIs to the v4l2 core. This is based on version v1.2
of the RFC titled "V4L - Support for video timings at the input/output interface"
Following new ioctls are added:-
- VIDIOC_ENUM_DV_PRESETS
- VIDIOC_S_DV_PRESET
- VIDIOC_G_DV_PRESET
- VIDIOC_QUERY_DV_PRESET
- VIDIOC_S_DV_TIMINGS
- VIDIOC_G_DV_TIMINGS
Please refer to the RFC for the details. This code was tested using vpfe
capture driver on TI's DM365. Following is the test configuration used :-
Blu-Ray HD DVD source -> TVP7002 -> DM365 (VPFE) ->DDR
A draft version of the TVP7002 driver (currently being reviewed in the mailing
list) was used that supports V4L2_DV_1080I60 & V4L2_DV_720P60 presets.
A loopback video capture application was used for testing these APIs. This calls
following IOCTLS :-
- verify the new v4l2_input capabilities flag added
- Enumerate available presets using VIDIOC_ENUM_DV_PRESETS
- Set one of the supported preset using VIDIOC_S_DV_PRESET
- Get current preset using VIDIOC_G_DV_PRESET
- Detect current preset using VIDIOC_QUERY_DV_PRESET
- Using stub functions in tvp7002, verify VIDIOC_S_DV_TIMINGS
and VIDIOC_G_DV_TIMINGS ioctls are received at the sub device.
- Tested on 64bit platform by Hans Verkuil
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video_device::minor field is used where it shouldn't, either to
- test for error conditions that can't happen anymore with the current
v4l-dvb core,
- store the value in a driver private field that isn't used anymore,
- check the video device type where video_device::vfl_type should be
used, or
- create the name of a kernel thread that should get a stable name.
Remove or fix those use cases.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace the video_is_unregistered function by a video_is_registered
function. The V4L2_FL_UNREGISTERED flag is replaced by a
V4L2_FL_REGISTERED flag.
This change makes the video_is_registered function return coherent
results when called on an initialize but not yet registered video_device
instance. The function can now be used instead of checking
video_device::minor.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many drivers access the device number (video_device::v4l2_devnode::num)
in order to print the video device node name. Add and use a helper
function to retrieve the video_device node name.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This IR uses NEC protocol, with address=0x14. This keymap is similar
to the existing Terratec Cinergy XS, except that:
- it contains the full address/command code;
- the Music button were mapped as KEY_RADIO;
- some keycodes from the previous entry were wrong, IMHO.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The same loop to seek for a key were used on different places. Also,
no spinlock were protecting it to avoid the risk of replacing a keycode
while seeking for a new code.
This cleanup does:
- create an unique function to seek for a code;
- adds an spinlock to protect the table lookup;
- remove some unused code;
- simplifies to code to make it easier to understand.
Basically no change in behavior should be noticed after this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the IR table is initialized by calling ir_input_init(). However,
this function doesn't return any error code, nor has a function to be called
when de-initializing the IR's.
Change the return argment to integer and make sure that each driver will
handle the error code. Also adds a function to free any resources that may
be allocating there: ir_input_free().
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that V4L drivers can support more than 7 bits for scan code, let's
add a modified version for the Hauppauge Grey IR containing the full IR
scancode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the IR conversion to dynamic tables has finished, we can get
rid of some fields and definitions that aren't used anymore.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L drivers use an static keycode vector with 128 entries, where the scancode
indexes the keycode. While this works, it limits the scancodes to have only
7 bits, not allowing for example full RC5 codes.
Instead of implementing the same code on every V4L driver, provide a common
infrastructure to handle the bigger tables, minimizing the changes inside
each driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As newer IR common code will be added on other files, we need a global
debug var inside the module.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The I2C adapter ID is actually depends on Board and may vary, Davinci
uses id=1, but in case of AM3517 id=3.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For whatever reason, the device structure pointer to
videobuf_queue_vmalloc_init is typed "void *", even though it's passed
right through to videobuf_queue_core_init(), which expects a struct
device pointer. The other videobuf implementations use struct device *;
I think vmalloc should too.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The videobuf_queue_ops function vector is not declared constant, but
there's no need for the videobuf layer to ever change it. Make it const
so that videobuf users can make their operations const without warnings.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Upcoming I2C v4l2_subdev drivers need a way to control the subdevice
power state from the core. This use case is already partially covered by
the tuner s_standby operation, but no way to explicitly come back from
the standby state is available.
Rename the tuner s_standby operation to core s_power, and fix tuner
drivers accordingly. The tuner core will call s_power(0) instead of
s_standby(). No explicit call to s_power(1) is required for tuners as
they are supposed to wake up from standby automatically.
[mchehab@redhat.com: CodingStyle fix]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for TEF6862 Car Radio Enhanced Selectivity Tuner.
It's implemented as a subdev, supporting checking signal strength
and setting and getting frequency.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch brings infrared remote support for some cx88 based cards.
Such as TeVii S460,S420.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch brings infrared remote support for some cx88 based cards.
Such as:
TeVii S460,S420; Omicom SS4; SatTrade ST4200;
TBS 8920,8910; Prof 7300,6200.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds an soc-camera / v4l2-subdev driver for the RJ54N1CB0C CMOS camera
sensor from Sharp. The sensor is very picky about initialisation and
configuration sequences. The driver limits artificially maximum window size by
800x600, although the sensor supports 1600x1200. Sizes above 800x600 don't seem
to work correctly, besides, examples from the system integrator use sizes above
640x480 only for still photography. Unfortunately, I had to use "magic"
register-value pairs for undocumented and "reserved" registers. This version of
the driver also omits some functionality, like cropping, which hasn't been
sufficiently tested yet and will be added later.
create mode 100644 drivers/media/video/rj54n1cb0c.c
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add v4l2_subdev_ir_ops and IR notify defines for v4l2_device. This change
is specifically needed at this time to support the integrated IR controller in
the CX2388[58] chips.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add identifiers for CX2388[578] chips, CX2310[012] chips, integrated
A/V decoders cores, integrated IR controller core, and the CX23417
MPEG encoder. The cx23885 module and cx25840 module will use these
identifiers in upcoming changes.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is an initial driver for Analog Devices ADV7180 Video Decoder.
So far it only supports query standard.
[akpm@linux-foundation.org: remove unneeded cast]
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Warn when the desired device node number is already in use, except when
the new video_register_device_no_warn function is called since in some
use-cases that warning is not relevant.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
video_register_device_index is never actually called, instead the
stream index number is always calculated automatically.
This patch removes this function and simplifies the internal get_index
function since that can now always just return the first free index.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rewrite v4l2_i2c_new_subdev as a simplified version of v4l2_i2c_new_subdev_cfg
and remove v4l2_i2c_new_probed_subdev and v4l2_i2c_new_probed_subdev_addr.
This simplifies this API substantially.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes the soc-camera interface for V4L2 subdevices thinner yet. Handle
gain and exposure internally in each driver just like all other controls.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove unneeded soc-camera operations, this also makes the soc-camera API to
v4l2 subdevices thinner.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The initial soc-camera scaling and cropping implementation turned out to be
incompliant with the V4L2 API, e.g., it expected the user to specify cropping
in output window pixels, instead of input window pixels. This patch converts
the soc-camera core and all drivers to comply with the standard.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use v4l2_subdev_call() instead of v4l2_device_call_until_err() in all host
drivers and in soc-camera core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove set_crop soc-camera device method and switch to s_crop from v4l2-subdev
video operations. Also extend non-i2c drivers to also hold a pointer to their
v4l2-subdev instance in control device driver-data, i.e., in
dev_get_drvdata((struct device *)to_soc_camera_control(icd))
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The move of format translation initialisation into soc_camera_open() was
temporary for the soc-camera as platform driver intermediate step, put it back
into soc_camera_probe(). Also add a .put_formats() method to
soc_camera_host_ops to free any resources host driver might have allocated in
.get_formats().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switch to using struct v4l2_rect in struct soc_camera_device for uniformity and
simplicity.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Until now soc-camera only supported client (sensor) controls. This patch
enables camera-host drivers to implement their own controls too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the soc-camera framework to use the v4l2-(sub)dev API. Start using
v4l2-subdev operations. Only a part of the interface between the
soc_camera core, soc_camera host drivers on one side and soc_camera device
drivers on the other side is replaced so far. The rest of the interface
will be replaced in incremental steps, and will require extensions and,
possibly, modifications to the v4l2-subdev code.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert soc-camera core and all drivers to platform device API. We already
converted platforms to register a platform device for each soc-camera client,
now we remove the compatibility code and switch completely to the new scheme.
This is a preparatory step for the v4l2-subdev conversion.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a struct device pointer to struct soc_camera_platform_info and let the user
(ap325rxa) pass it down to soc_camera_platform.c in its .add_device() method.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
soc_camera_platform.c is only used by y SuperH ap325rxa board. This patch
converts soc_camera_platform.c and its users for the soc-camera platform-
device conversion and also extends soc-camera core to handle non-I2C cameras.
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a new module added for vpss library functions that are
used for configuring vpss system module. All video drivers will
include vpss.h header file and call functions defined in this
module to configure vpss system module.
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the hw module for DM644x CCDC. This registers with the
vpfe capture driver and provides a set of hw_ops to configure
CCDC for a specific decoder device connected to the VPFE.
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds ccdc hw module for DM355 CCDC. This registers with the bridge
driver a set of hw_ops for configuring the CCDC for a specific
decoder device connected to vpfe.
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This the vpfe capture bridge driver for doing video
capture on DM355 and DM6446 evms. The ccdc hw modules register with the
driver and are used for configuring the CCD Controller for a specific
decoder interface. The driver also registers the sub devices required
for a specific evm. More than one sub devices can be registered.
This allows driver to switch dynamically to capture video from
any sub device that is registered. Currently only one sub device
(tvp5146) is supported. But in future this driver is expected
to do capture from sensor devices such as Micron's MT9T001, MT9T031
and MT9P031 etc. The driver currently supports MMAP based IO.
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for NXP TDA18271 as a standalone tuner, allowing the use of
analog demodulators other than the Philips/NXP TDA829x.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, V4L uses a scancode table whose index is the scancode and
the value is the keycode. While this works, it has some drawbacks:
1) It requires that the scancode to be at the range 00-7f;
2) keycodes should be masked on 7 bits in order for it to work;
3) due to the 7 bits approach, sometimes it is not possible to replace
the default keyboard to another one with a different encoding rule;
4) it is different than what is done with dvb-usb approach;
5) it requires a typedef for it to work. This is not a recommended
Linux CodingStyle.
This patch is part of a larger series of IR changes. It basically
replaces the IR_KEYTAB_TYPE tables by a structured table:
struct ir_scancode {
u16 scancode;
u32 keycode;
};
This is very close to what dvb does. So, a further integration with DVB
code will be easy.
While we've changed the tables, for now, the IR keycode handling is still
based on the old approach.
The only notable effect is the redution of about 35% of the ir-common
module size:
text data bss dec hex filename
6721 29208 4 35933 8c5d old/ir-common.ko
5756 18040 4 23800 5cf8 new/ir-common.ko
In thesis, we could be using above u8 for scancode, reducing even more the size
of the module, but defining it as u16 is more convenient, since, on dvb, each
scancode has up to 16 bits, and we currently have a few troubles with rc5, as their
scancodes are defined with more than 8 bits.
This patch itself shouldn't be doing any functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: Fix a few wrong IR keymaps]
Signed-off-by: Shine Liu <shinel@foxmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds files to control si4713 devices.
Internal functions to control device properties
and initialization procedures are into these files.
Also, a v4l2 subdev interface is also exported.
This way other drivers can use this as v4l2 i2c subdevice.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds files which creates the radio interface
for si4713 FM transmitter (modulator) devices.
In order to do the real access to device registers, this
driver uses the v4l2 subdev interface exported by si4713 i2c driver.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the remote control that comes with the Cinergy Hybrid T USB XS
Thanks to Jelle de Jong for providing sample hardware to test with.
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch augments the init data passed by bridge drivers to
ir-kbd-i2c, so that the ir_type can be set explicitly, and so
ir-kbd-i2c internal get_key functions can be reused without
requiring symbols from ir-kbd-i2c in the bridge driver.
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds driver for mt9v011 based on its datasheet, available at:
http://download.micron.com/pdf/datasheets/imaging/MT9V011.pdf
The driver was tested with a webcam that will be added on a next patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Most hardware has limits on minimum and maximum image dimensions and also
requirements about alignment. For example, image width must be even or a
multiple of four. Some hardware has requirements that the total image size
(width * height) be a multiple of some power of two.
v4l_bound_align_image() will enforce min and max width and height, power of
two alignment on width and height, and power of two alignment on total
image size.
It uses an efficient algorithm that will try to find the "closest" image
size that meets the requirements.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a new s_config core ops call: this is called with the irq and platform
data to be used to initialize the subdev.
Added new v4l2_i2c_new_subdev_cfg and v4l2_i2c_new_subdev_board calls
that allows you to pass these new arguments.
The existing v4l2_i2c_new_subdev functions were modified to also call
s_config.
In the future the existing v4l2_i2c_new_subdev functions will be replaced
by a single v4l2_i2c_new_subdev function similar to v4l2_i2c_new_subdev_cfg
but without the irq and platform_data arguments.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it very clear that this header should not be used for i2c drivers that
do not need to be compiled for pre-2.6.26 kernels.
As soon as the minimum supported kernel in the v4l-dvb repository becomes
2.6.26 or up, then this header should be removed entirely.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an IR profile for the EVGA inDtube remote control (which is an NEC type
remote)
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For specific boards, pass initialization data to ir-kbd-i2c instead
of modifying the settings after the device is initialized. This is
more efficient and easier to read.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let card drivers probe for IR receiver devices and instantiate them if
found. Ultimately it would be better if we could stop probing
completely, but I suspect this won't be possible for all card types.
There's certainly room for cleanups. For example, some drivers are
sharing I2C adapter IDs, so they also had to share the list of I2C
addresses being probed for an IR receiver. Now that each driver
explicitly says which addresses should be probed, maybe some addresses
can be dropped from some drivers.
Also, the special cases in saa7134-i2c should probably be handled on a
per-board basis. This would be more efficient and less risky than always
probing extra addresses on all boards. I'll give it a try later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the standard device driver binding model, the name field of
struct i2c_client is used to match devices to their drivers, so we
must stop using it for internal purposes. Define a separate field
in struct IR_i2c as a replacement, and use it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add ADV7343 I2C based video encoder driver. This follows the
v4l2-subdev framework. This driver has been tested on TI DM646x EVM. It
has been tested for Composite and Component outputs.
Updates as per review by Mauro Chehab, added support for more standards
supported by the encoder. Also adding the missed out signed-offs.Tested
only NTSC and PAL standards.
[hverkuil@xs4all.nl: s_routing API changed, updated driver to use new API]
Signed-off-by: Manjunath Hadli <mrh@ti.com>
Signed-off-by: Brijesh Jadav <brijesh.j@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds driver for TI THS7303 video amplifier. This driver is
implemented as a v4l2 sub device. Tested on TI DM646x EVM.
This version has updates based on review comments by Mauro Chehab.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a platform driver to soc_camera.c. This way we preserve backwards
compatibility with existing platforms and can start converting them one by one
to the new platform-device soc-camera interface.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Until now I relied on i2c_del_adapter to unregister the i2c_clients for
me, however, if the i2c bus is a platform bus then it is never deleted.
So instead I need to unregister i2c clients when unregistering the
v4l2_device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a utility function that can be used to setup the v4l2_device's name
field in a standard manner.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make camera devices direct children of host platform devices, move the
inheritance management into the soc_camera.c core driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently pcm990 camera bus-width management functions request a GPIO and never
free it again. With this approach the GPIO extender driver cannot be unloaded
once camera drivers have been loaded, also unloading theb i2c-pxa bus driver
produces errors, because the GPIO extender driver cannot unregister properly.
Another problem is, that if camera drivers are once loaded before the GPIO
extender driver, the platform code marks the GPIO unavailable and only a reboot
helps to recover. Adding an explicit free_bus method and using it in mt9m001
and mt9v022 drivers fixes these problems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The name size limit is gone from the driver core, the BUS_ID_SIZE
value will be removed.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove support for the debug call VIDIOC_INT_S_AUDIO_ROUTING from cx18
and ivtv. These internal ioctls shouldn't be exposed. These were only
used through the cx18-ctl and ivtv-ctl utilities, and only when testing
a new card variant.
This cleanup allows the removal of this ioctl from v4l2-common.h.
Cc: Andy Walls <awalls@radix.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is no longer needed to use a struct pointer as argument, since v4l2_subdev
doesn't require that ioctl-like approach anymore. Instead just pass the input,
output and config (new!) arguments directly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With all the v4l2_subdev changes that were made to these drivers it is a
good idea to increase the version number of each driver.
It's just the patch level that is increased, except for the zoran and saa7146
drivers where the minor number was increased due to the more substantial
changes that were made to those two drivers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than duplicating this list everywhere, just put it in tvaudio.h.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The functions v4l2_i2c_new_subdev and v4l2_i2c_new_probed_subdev relied on
i2c_get_adapdata to return the v4l2_device. However, this is not always
possible on embedded platforms. So modify the API to pass the v4l2_device
pointer explicitly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add utility function to probe for a single address, rather than a list
of addresses.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Originally the intention was to switch to the new style i2c API starting with
the introduction of the API in 2.6.22. However, the i2c_new_probed_device()
function has a lethal bug that wasn't fixed until 2.6.25. Or more accurately,
it was only fixed in the stable series of 2.6.25 and 2.6.26.
Given the fact that the new i2c API also changed starting with 2.6.26 (the
addition of i2c_device_id), it is easiest to switch APIs starting with
2.6.26.
This patch updates all the legacy code accordingly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s_std didn't belong in the tuner ops. Stricly speaking it should be part of
the video ops, but it is used by audio and tuner devices as well, so it is
more efficient to make it part of the core ops.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The init callback was used in several places to load firmware. Make a separate
load_fw callback for that. This makes the code a lot more understandable.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s_standby is only used to put the tuner in powersaving mode, so move it
from core to tuner.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that all drivers are converted to v4l2_subdev we can remove legacy code
in v4l2-common. Also move the documentation of the internal API to
v4l2-subdev.h where it really belongs.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2-subdev.c and v4l2-i2c-drv-legacy.h were used to support the old i2c
API. All v4l drivers are now converted to v4l2_subdev, so these two files
can be removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Shared memory mappings on nommu machines require a get_unmapped_area
file operation that suggests an address for the mapping. This patch
adds a way for v4l2 drivers to provide this callback.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using VIDIOC_DBG_S/G_REGISTER is the standard way of reading/writing register
for advanced debugging under v4l2. In addition, using this means that the
cafe_ccic driver doesn't need to have knowledge about the used sensor: the
debug ioctl can be passed on to the sensor if it isn't for the host.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These ops are used by the ov7670 driver, so these need to be added.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the g_chip_ident call work for the au0828/au8522. Discovered when testing
with the v4l2_compliance tool
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
[mchehab@redhat.com: fix merge conflict, due to a path change for analog demod]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Call v4l2_device_disconnect when the parent of a hotpluggable device
disconnects. This ensures that you do not have a pointer to a device that
is no longer present.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Camera sensors have a native bus width say support, but on some
boards not all sensor data lines are connected to the image
interface and thus support a different bus width than the sensors
native one. Some boards even have a bus driver which dynamically
switches between different bus widths with a GPIO.
This patch adds a hook which board code can use to support different
bus widths.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently soc-camera doesn't set up any image format without an explicit
S_FMT. According to the API this should be supported, for example,
capture-example.c from v4l2-apps by default doesn't issue an S_FMT. This
patch moves negotiating of available host-camera format translations to
probe() time, and restores the state from the last close() on the next
open(). This is needed for some drivers, which power down or reset
hardware after the last user closes the interface. This patch also has a
nice side-effect of avoiding multiple allocation anf freeing of format
translation tables.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As host and camera drivers become more complex, differences between S_FMT and
S_CROP functionality grow, this patch separates them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bt819 needs the parent driver to drive a GPIO pin low and high in order to
reset its fifo. Use the new notify callback for this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a notify callback to v4l2_device to let sub-devices notify their
parent of special events.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The removal of the timer which polls the infrared input is racy.
Replacing the timer with a delayed work solves the problem.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some code was calling v4l2_video_std_construct() when all it cared about
was the frame period. So make a function that just returns that and have
v4l2_video_std_construct() use it.
At this point there are no users of v4l2_video_std_construct() left outside
of v4l2-ioctl, so it could be un-exported and made static.
Change v4l2_video_std_construct() so that it doesn't zero out the struct
v4l2_standard passed in. It's already been zeroed out in the common ioctl
code.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added a new chip identifer to v4l2-chip-ident for the integrated A/V broadcast
decoder core internal to the CX23418. Completed separation and encapsulation
of the A/V decoder core interface as a v4l2_subdevice. The cx18 driver now
compiles and links again.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver infrared remote code part is altered to switch to a work queue.
Also ir_codes table moved to ir-common module for shared access.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2_ctrl_query_fill_std() function wasn't one the best idea I ever had.
It doesn't add anything valuable that cannot be expressed equally well with
v4l2_ctrl_query_fill and only adds overhead.
Replace it with v4l2_ctrl_query_fill() everywhere it is used and remove it
from v4l2_common.c.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add small function to retrieve the i2c address from a v4l2_subdev
pointer.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add data signal polarity, mode, and bus-width tests to
soc_camera_bus_param_compatible().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
sh_mobile_ceu_camera.c support for signal polarity flags isn't platform
dependent, provide them locally. Only the bus width is implementation
specific.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remain consistent in the naming: fields pointing to v4l2_device should
be called v4l2_dev. There are too many device-like entities without
adding to the confusion by mixing naming conventions.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some drivers (e.g. for ISA devices) have no parent device because there
is no associated bus driver. Allow the parent device to be NULL in
those cases when registering v4l2_device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added support for I2C device at address 0x40 and subaddress 0x0d/0x0b
that provides remote control key reading support for AVerMedia Cardbus
Hybrid card, possibly for other AVerMedia Cardbus cards.
The I2C address 0x40 doesn't like the SAA7134's 0xfd quirk, so it was
disabled.
[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Oldřich Jedlička <oldium.pro@seznam.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Control arrays as are used with v4l2_ctrl_next must be sorted from
low to high. Add a comment at the top of all such arrays to warn
about this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to convert the v4l1 zoran and vino i2c drivers to v4l2 these
extra ops are required.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Kaiomy entry.
Thanks to Peter Senna Tschudin <peter.senna@gmail.com> for borrow me one
of those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Modified mxb to load the i2c modules through v4l2_subdev. So no more probing.
Modified tea6415c and tea6420 to use the standard routing ops to do the
routing, rather than using private commands. Dropped the private commands
from tda9840 (they were never used except during initialization of the
module).
Added saa7146 support for VIDIOC_DBG_G_CHIP_IDENT.
Converted saa5246a and saa5249 to v4l2_subdev.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix bugs in the cx18 AC3 control implementation that would have affected
ivtv and other drivers via the cx2341x module. Bring AC3 controls
behavior into comliance with V4L2 specification. Thanks to Hans Verkuil
for reviewing the previous patch and pointing out the problems.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initial addition of controls to set AC-3 audio encoding for the CX23418 - it
does not work yet due to firmware or cx18 driver issues. This change affects
the common cx2341x and ivtv modules due to shared structures and
common functions.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The conversion to video_ioctl2 is the first phase to converting this driver
to the latest v4l2 framework.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add v4l2_i2c_tuner_addrs() to obtain the various I2C tuner addresses.
This will be used in several drivers, so make this a common function
as we do not want to have these I2C addresses all over the place.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move DMA-mapping.txt to Documentation/PCI/.
DMA-mapping.txt was supposed to be moved from Documentation/ to
Documentation/PCI/. The 00-INDEX files in those two directories
were updated, along with a few other text files, but the file
itself somehow escaped being moved, so move it and update more
text files and source files with its new location.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the i2c driver ID will be removed in the near future we have to
modify the v4l2 debugging API to use the driver name instead of driver ID.
Note that this API is not used in applications other than v4l2-dbg.cpp
as it is for debugging and testing only.
Should anyone use the old VIDIOC_G_CHIP_IDENT, then this will be logged
with a warning that it is deprecated and will be removed in 2.6.30.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This rename prevents conflicts with the older compat_ioctl32 module.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since internal to v4l2 the ioctl prototype is the same regardless of it
being called through .ioctl or .unlocked_ioctl, we need to convert it all
to the long return type of unlocked_ioctl.
Thanks to Jean-Francois Moine for posting an initial patch for this and
thus bringing it to our attention.
Cc: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce a struct v4l2_file_operations for v4l2 drivers.
Remove the unnecessary inode argument.
Move compat32 handling (and llseek) into the v4l2-dev core: this is now
handled in the v4l2 core and no longer in the drivers themselves.
Note that this changeset reverts an earlier patch that changed the return
type of__video_ioctl2 from int to long. This change will be reinstated
later in a much improved version.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes this warning:
drivers/media/video/gspca/gspca.c:1811: warning: initialization from incompatible pointer type
The reason is that the returned argument should be a long, not an
integer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This camera is rather similar to MT9M001, but also has a couple of
enhanced features, like pixel binning.
create mode 100644 drivers/media/video/mt9t031.c
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds tw9910 driver that use soc_camera framework.
It was tested on SH Migo-r board and mplayer.
create mode 100644 drivers/media/video/tw9910.c
create mode 100644 include/media/tw9910.h
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In preparation for i.MX31 camera host driver add flags for 4 and 15 bit bus
widths and for data lines polarity inversion.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch presents new method to be able to select V4L2 input type
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch presents new method to be able to check v4l2_std_id
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move mutex from host drivers to camera device object, take into account
videobuf locking.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The chip is largely compatible with MT9M111 and is going to be supported by the
same driver.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a struct soc_camera_sense, that can be used by camera host drivers to
request additional information from a camera driver, for example, when
changing data format. This struct can be extended in the future, its first use
is to request the camera driver whether the pixel-clock frequency has changed.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Antonio Ospite <ospite@studenti.unina.it> two platforms with a
mt9m111 camera require opposite pixel clock polarity, which means one of them
inverts it. This patch adds support for inversion flags and switches all
available camera drivers to using them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers that use v4l2_device can set that as parent pointer in the v4l2_dev
field instead of using the struct device parent field.
This allows v4l2-dev.c to check whether this driver is v4l2_device based,
and if so then it can offer additional services.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of relying on the cdev release callback we should rely on the
release callback from the device struct. This requires that we use
get_device/put_device to do proper refcounting. In order to do this
safely v4l2-dev.c now sets up its own file_operations that call
out to the driver's ops.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bt832 i2c driver was never used or even compiled and is no longer
maintained. It is now removed completely.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add helper functions to load i2c sub-devices, integrating them
into the v4l2-framework.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allocate and fill a list of formats, supported by this specific
camera-host combination. Use it for format enumeration. Take care to stay
backwards-compatible.
Camera hosts rely on sensor formats available, as well as
host specific translations. We add a structure so that hosts
can define a translation table and use it for format check
and setup.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This pointer will be used by pxa_camera.c to point to its pixel format
data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We anyway don't follow the s_fmt_vid_cap / g_fmt_vid_cap / try_fmt_vid_cap
naming, and soc-camera is so far only about video capture, let's simplify
operation names a bit further. set_fmt_cap / try_fmt_cap wasn't a very good
choice too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pixel format requested by the user is not necessarily the same, as what
a sensor driver provides. There are situations, when a camera host driver
provides the required format, but requires a different format from the
sensor. Further, the list of formats, supported by sensors is pretty static
and can be pretty good described with a constant list of structures. Whereas
decisions, made by camera host drivers to support requested formats can be
quite complex, therefore it is better to let the host driver do the work.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
.try_bus_param() method from struct soc_camera_host_ops is only called at one
location immediately before .try_fmt_cap(), there is no value in keeping these
two methods separate, merge them.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this
development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the ATI TV Wonder HD 600 USB Remote Control
(required a new keymap)
[mchehab@redhat.com: Fix CodingStyle]
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
video_ioctl2 lacks implementation of those two ioctls:
- VIDIOC_ENUM_FRAMESIZES and VIDIOC_ENUM_FRAMEINTERVALS
Adds implementation for those.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
We want to submit a patch to -next, which will remove bus_id from
"struct device", to find the remaining pieces to convert, and finally
switch over to the new api, which will remove the 20 bytes array
and does no longer have a size limitation.
Thanks,
Kay
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The inode argument was never used. Removing it from video_usercopy
brings the function pointer type of video_usercopy in line with similar
v4l2 functions, thus simplifying several drivers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds ov772x driver that use soc_camera framework.
It was tested on SH Migo-r board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This creates a self contained frontend de-allocator
for the instances where an adapter has not been
registered yet frontend de-allocation may
be required.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
inode is never used on video_ioctl2. Remove it and rename the function to
__video_ioctl2. This allows its usage directly as a callback at
fops.unlocked_ioctl.
Since we still need a callback with inode to be used with fops.ioctl,
this patch adds video_ioctl2() that is just a call to __video_ioctl2().
Also, this patch adds some comments about video_ioctl2 and __video_ioctl2
usage at v4l2-ioctl.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The inode parameter at v4l_compat_translate_ioctl() were just passed over several
places just to keep compatible with fops.ioctl. However, it weren't used anywere.
This patch gets hid of this unused parameter.
Cc: Laurent Pinchart <laurent.pinchart@skynet.be>
Cc: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on an older patch from Sakari Ailus.
Cc: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Export v4l2_int_device_try_attach_all. This allows initiating the
initialisation of int if device after the drivers have been registered.
Also allow drivers to call ioctls if v4l2-int-if was compiled as
module.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use enum v4l2_power instead of int as second argument to
vidioc_int_s_power. The new functionality is that standby state is also
recognised.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vidioc_int_g_priv is used to get master's slave-related private data
structure. The structure can contain for example master's configuration
specific to slave.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch marks those two functions as static:
static int videobuf_dvb_register_adapter(struct videobuf_dvb_frontends *fe,
static int videobuf_dvb_register_frontend(struct dvb_adapter *adapter,
Since MFE patches changed their calls by videobuf_dvb_register_bus.
To avoid having to declare the prototypes, the patch moves
videobuf_dvb_register_bus() to be after the declaration of the above functions
used there.
Cc: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To optimise data storage even further one other redundant
var has been removed.
This also removes a redundant assignment.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This tuner was already supported by proxy as an FMD1216ME, however,
the MEX uses a different FM Radio IF so this addition is now required.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To optimise data storage redundant vars are removed.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switching sensors on and off is now done by sensor drivers themselves,
typically using platform-provided hooks. Update soc_camera_platform.c to
do the same. Also remove a refundant struct soc_camera_platform_info
definition from soc_camera_platform.c.
Tested-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This add frontend R/W mutual exclusion.
Prior to this point in time it was possible to open both
frontends simultaneously which an MFE card cannot support.
In order to stop this, a delayed open is performed which
has the following function:
- Return EBUSY after a configurable amount of time
if a frontend is unavailable due to the other being
in use.
- Only allow opening of a frontend if the kernel thread
of the other has stopped.
This solution was chosen to allow switching between
frontends to work as seamlessly as possible. When both
frontends are actually opened simultaneously then one
will only open, but if quick switching is performed
between one of many then the new open will succeed in
a clean fashion rather than interrupting a kernel
thread.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds a configurable (one per card) gate control option
for multi-frontend. Prior to this point gate control was
assumed to be on the primary frontend, this is a fault
when the gate to the analogue section is on the secondary
which is the default for both the HVR-3000 and HVR-4000
in MFE.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A detailed description from the original patches 2 years ago:
"The WinTV-HVR3000 has a single transport bus which is shared between
a DVB-T and DVB-S modulator. These patches build on the bus acquisition
cx88 work from a few weeks ago to add support for this.
So to applications the HVR3000 looks like this:
/dev/dvb/adapter0/fe0 (cx24123 DVB-S demod)
/dev/dvb/adapter0/fe1 (cx22702 DVB-T demod)
Additional boards continue as before, eg:
/dev/dvb/adapter1/fe0 (lgdt3302 ATSC demod)
The basic change is removing the single instance of the videobuf_dvb in
cx8802_dev and saa7134_dev(?) and replacing it with a list and some
supporting functions.
*NOTE* This branch was taken before v4l-dvb was closed for 2.6.19 so
two or three current cx88 patches appear to be reversed by this tree,
this will be cleaned up in the near future. The patches missing change
the mutex handing to core->lock, fix an enumeration problem."
It should be recognised that a number of people have been maintaining
this patchset. Significant levels of Kudos to everyone one involved,
including but not limited to:
Darron Broad
Fabio M. Di Nitto
Carlo Scarfoglio
Hans Werner
Without the work of these people, and countless others, my two year old
patches would of died on the Mercurial linuxtv.org vine a long time
ago.
TODO: Revise these patches a little further so that the need for
demux1 and dvr0 is optional, not mandatory on the HVR3000.
HISTORY (darron):
This is the last update to MFE prepared by Hans which is based
upon the `scratchpad' diff created by Carlo.
All MFE work prior to that point must be attributed to Fabio
who ported and maintained Steve's original patch up to that
time.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Looking at these headers as they appear in the kernel makes you
wonder why it is done that way. Refer to the v4l-dvb repository
where the full unstripped header can be found to understand the
reasoning behind this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The IR controller has a couple quirks. It won't respond until some other
device on the bus is probed. To work around that, probe 0x50 first.
Then, since it won't respond to a zero-byte read, probe with a one-byte
read.
Signed-off-by: Brian Rogers <brian_rogers@comcast.net>
[mchehab.redhat.com: Fix merge conflicts and remove an unused var]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the vidioc_enum_fmt_vbi_cap ops: it was scheduled for removal in
2.6.28 since the v4l2 specification says that V4L2_BUF_TYPE_VBI_CAPTURE should
not support VIDIOC_ENUM_FMT. It's also pretty pointless.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l core creates four different video devices (video, vbi, radio, vtx)
and each has its own range of minor numbers. However, modern devices keep
increasing the number of devices that they need so a maximum of 64 video
devices will not be enough in the future. In addition this scheme makes
it very hard to add new device types.
This patch disconnects the kernel number allocation (e.g. video0, video1,
etc.) from the actual minor number (just pick the first free minor).
This allows for much more flexibility in the future. However, it does
require the use of udev. For those who cannot use udev a new CONFIG option
was created that changes the allocation scheme back to the old behavior.
Thanks to Greg KH for suggesting this approach during the 2008 LPC.
In addition, several bugs were fixed in the ivtv and cx18 drivers: these
drivers try to allocate specific kernel numbers but that scheme contained
a bug which caused what should have been e.g. video17 to appear as e.g.
video2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The saa7111 support in saa7115.c was missing some features and did not
properly take some of the differences into account. With this patch
saa7115 can be used in the mxb driver instead of saa7111.c.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace the old register_chrdev with the more flexible register_chrdev_region.
Ensure that the release() is called when the very last chardev usage was
released, and not when the sysfs devices were removed. This should simplify
hotpluggable drivers considerably.
Tested-by: Mike Isely <isely@isely.net>
Tested-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: David Ellingsworth <david@identd.dyndns.org>
Reviewed-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cleanup v4l2-dev.[ch], add/improve comments and add a new helper
function: video_drvdata() that can get the private driver data from
a file struct.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the priv field and let video_get/set_drvdata use dev_get_drvdata
and dev_set_drvdata instead.
Convert all drivers that still used priv directly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a second release function: video_device_release_empty
It can be used by drivers that have statically allocated
video_device structs.
Its use usually, but not always, indicates laziness on the
part of the driver programmer.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Guennadi Liakhovetski