Commit Graph

505 Commits

Author SHA1 Message Date
Hiroshi DOYU 8828880d09 omap: mailbox: Flush posted write when acking mailbox irq
The only way to flush posted write to L4 bus is to do a read back
of the same register right after the write.

This seems to be mostly needed in interrupt handlers to avoid
causing spurious interrupts.

The earlier fix has been to mark the L4 bus as strongly ordered
memory, which solves the problem, but causes performance penalties.

Similar to the fix, 03803a71041e3bc3c077f4e7b92f6ceaa9426df3

Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-09-24 16:23:10 -07:00
Hiroshi DOYU 1ffe627dcf omap: mailbox: Execute softreset at startup
The softreset at startup is introduced as TRM describes and also some
register bit definitions are added instead of magic number.

Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-09-24 16:23:09 -07:00
Ajay Kumar Gupta 41a03c539c omap: Add missing mux pin for EHCI phy reset line
GPIO135 is used as EHCI (port2) phy reset pin on Multi Media Daughter card
connected to OMAP3EVM.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-09-24 16:23:08 -07:00
Tony Lindgren 61f04ee83c omap: Fix 44xx compile
Looks like these patches were not tested that well..

Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-09-24 16:23:07 -07:00
Tony Lindgren af41a12f09 omap: Fix mcspi compile for 2420
Commit 7869c0b9ed added support for
additional McSPI ports. Unfortunately that broke compile for 2420.

Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-09-24 16:23:05 -07:00
Tony Lindgren 5328ae3af1 omap: Fix compile for arch/arm/mach-omap2
Patch 941132606c split IO_ADDRESS
into OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS except for the omap4
code to avoid merge conflicts with the omap4 code that was queued
earlier.

Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-09-24 16:23:04 -07:00
Linus Torvalds a7c367b95a Merge git://git.infradead.org/mtd-2.6
* git://git.infradead.org/mtd-2.6: (58 commits)
  mtd: jedec_probe: add PSD4256G6V id
  mtd: OneNand support for Nomadik 8815 SoC (on NHK8815 board)
  mtd: nand: driver for Nomadik 8815 SoC (on NHK8815 board)
  m25p80: Add Spansion S25FL129P serial flashes
  jffs2: Use SLAB_HWCACHE_ALIGN for jffs2_raw_{dirent,inode} slabs
  mtd: sh_flctl: register sh_flctl using platform_driver_probe()
  mtd: nand: txx9ndfmc: transfer 512 byte at a time if possible
  mtd: nand: fix tmio_nand ecc correction
  mtd: nand: add __nand_correct_data helper function
  mtd: cfi_cmdset_0002: add 0xFF intolerance for M29W128G
  mtd: inftl: fix fold chain block number
  mtd: jedec: fix compilation problem with I28F640C3B definition
  mtd: nand: fix ECC Correction bug for SMC ordering for NDFC driver
  mtd: ofpart: Check availability of reg property instead of name property
  driver/Makefile: Initialize "mtd" and "spi" before "net"
  mtd: omap: adding DMA mode support in nand prefetch/post-write
  mtd: omap: add support for nand prefetch-read and post-write
  mtd: add nand support for w90p910 (v2)
  mtd: maps: add mtd-ram support to physmap_of
  mtd: pxa3xx_nand: add single-bit error corrections reporting
  ...
2009-09-23 10:07:49 -07:00
Syed Rafiuddin 7869c0b9ed spi: McSPI support for OMAP4
tAdd adds McSPI support for OMAP4430 SDP platform.  All the base addresses
are changed between OMAP1/2/3 and OMAP4.  The fields of the resource
structures are filled at runtime to have McSPI support on OMAP4.

Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:44 -07:00
kishore kadiyala 82cf818d54 omap4: mmc driver support on OMAP4
Add basic support for all 5 MMC controllers on OMAP4.

This patch doesn't include mmc-regulator support

Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:37 -07:00
Adrian Hunter 5e763d2968 ARM: OMAP: RX51: set MMC capabilities and power-saving flag
Specify MMC capabilities and set the power-saving flag for RX51.

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:36 -07:00
Adrian Hunter 9b7c18e070 ARM: OMAP: mmc-twl4030: add regulator sleep / wake function
Add the ability for the driver to put the card power regulators to sleep
and wake them up again.

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:35 -07:00
Denis Karpov dd498effcf omap_hsmmc: support for deeper power saving states
Support for multi-level dynamic power saving states in omap_hsmmc
(ENABLED->DISABLED->OFF).  In the "deepest" state (OFF) we switch off the
voltage regulators.

Signed-off-by: Denis Karpov <ext-denis.2.karpov@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:35 -07:00
Adrian Hunter 23d99bb923 omap_hsmmc: make use of new MMC_CAP_NONREMOVABLE host capability
Let the board specify that a card is nonremovable e.g. eMMC

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:35 -07:00
Denis Karpov 1887bde391 ARM: OMAP: mmc-twl4030: add context loss counter support
PM dynamic OFF state results in context loss.  That is, the host
controller has been powered off at some point, which means the registers
have been reset.  The driver must detect when this happens, and restore
the context.  This patch adds the means to detect context loss.

Note, the PM side is not yet implemented.

Signed-off-by: Denis Karpov <ext-denis.2.karpov@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:34 -07:00
David Woodhouse 6469f540ea Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
	drivers/mtd/mtdcore.c

Merged in order that I can apply the Nomadik nand/onenand support patches.
2009-09-20 05:55:36 -07:00
vimal singh 59e9c5ae17 mtd: omap: add support for nand prefetch-read and post-write
This patch adds prefetch support to access nand flash in mpu mode.
This patch also adds 8-bit nand support (omap_read/write_buf8).
Prefetch can be used for both 8- and 16-bit devices.

Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-09-19 13:20:51 -07:00
Magnus Damm 778dbcc1eb mtd: onenand: make onenand/generic.c more generic
Remove the ARM dependency from the generic "onenand" platform device
driver.  This change makes the driver useful for other architectures as
well.  Needed for the SuperH kfr2r09 board.

Apart from the obvious Kconfig bits, the most important change is the move
away from ARM specific includes and platform data.  Together with this
change the only in-tree board code gets an update, and the driver name is
also changed gracefully break potential out of tree drivers.

The driver is also updated to allow NULL as platform data together with a
few changes to make use of resource_size() and dev_name().

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-09-19 11:07:50 -07:00
Linus Torvalds 6f130478e2 Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (55 commits)
  regulator: Voltage count for AB3100
  mfd: Convert WM8350 to use request_threaded_irq()
  mfd: Update MAINTAINERS patterns for WM831x
  mfd: Fix twl4030-power warnings
  regulator: AB3100 support
  rtc: AB3100 RTC support
  mfd: Fix ab3100-otp build failure
  mfd: OMAP: Board-specifc twl4030 DPS scripts for RX51 board
  mfd: Print warning for twl4030 out-of-order script loading
  mfd: Add support for TWL4030/5030 dynamic power switching
  mfd: AB3100 OTP readout
  regulator: Add Freescale MC13783 driver
  mfd: Add Freescale MC13783 driver
  mfd: AB3100 disable irq nosync
  mfd: AB3100 alter default setting
  mfd: AB3100 propagate error
  mfd: AB3100 accessor function cleanups
  rtc: Add support for RTCs on Wolfson WM831x devices
  regulator: get pcap data from the parent device
  input: PCAP2 misc input driver
  ...
2009-09-18 09:22:36 -07:00
Linus Torvalds 73c583e4e2 Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (47 commits)
  OMAP clock: use debugfs_remove_recursive() for rewinding
  OMAP2/3/4 core: create omap_device layer
  OMAP: omap_hwmod: call omap_hwmod init at boot; create interconnects
  OMAP2/3/4: create omap_hwmod layer
  OMAP2/3 board-*.c files: read bootloader configuration earlier
  OMAP2/3/4 PRCM: add module IDLEST wait code
  OMAP2/3 PM: create the OMAP PM interface and add a default OMAP PM no-op layer
  OMAP3 clock: remove superfluous calls to omap2_init_clk_clkdm
  OMAP clock: associate MPU clocks with the mpu_clkdm
  OMAP3 clock: Fixed processing of bootarg 'mpurate'
  OMAP: SDRC: Add several new register definitions
  OMAP: powerdomain: Fix overflow when doing powerdomain deps lookups.
  OMAP: PM: Added suspend target state control to debugfs for OMAP3
  OMAP: PM debug: Add PRCM register dump support
  OMAP: PM debug: make powerdomains use PM-debug counters
  OMAP: PM: Add pm-debug counters
  OMAP: PM: Add closures to clkdm_for_each and pwrdm_for_each.
  OMAP: PM: Hook into PM counters
  OMAP: PM counter infrastructure.
  OMAP3: PM: fix lockdep warning caused by omap3_pm_init
  ...
2009-09-18 09:19:26 -07:00
Amit Kucheria 9312fffbad mfd: OMAP: Board-specifc twl4030 DPS scripts for RX51 board
Add support for Dynamic Power Switching (DPS) for the RX51 board.

These scripts are still a work-in-progress. I'll keep sending patches to
update the scripts as they are optimised.

Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-09-17 09:47:23 +02:00
Linus Torvalds 2ca7d674d7 Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (257 commits)
  [ARM] Update mach-types
  ARM: 5636/1: Move vendor enum to AMBA include
  ARM: Fix pfn_valid() for sparse memory
  [ARM] orion5x: Add LaCie NAS 2Big Network support
  [ARM] pxa/sharpsl_pm: zaurus c3000 aka spitz: fix resume
  ARM: 5686/1: at91: Correct AC97 reset line in at91sam9263ek board
  ARM: 5640/1: This patch modifies the support of AC97 on the at91sam9263 ek board
  ARM: 5689/1: Update default config of HP Jornada 700-series machines
  ARM: 5691/1: fix cache aliasing issues between kmap() and kmap_atomic() with highmem
  ARM: 5688/1: ks8695_serial: disable_irq() lockup
  ARM: 5687/1: fix an oops with highmem
  ARM: 5684/1: Add nuc960 platform to w90x900
  ARM: 5683/1: Add nuc950 platform to w90x900
  ARM: 5682/1: Add cpu.c and dev.c and modify some files of w90p910 platform
  ARM: 5626/1: add suspend/resume functions to amba-pl011 serial driver
  ARM: 5625/1: fix hard coded 4K resource size in amba bus detection
  MMC: MMCI: convert realview MMC to use gpiolib
  ARM: 5685/1: Make MMCI driver compile without gpiolib
  ARM: implement highpte
  ARM: Show FIQ in /proc/interrupts on CONFIG_FIQ
  ...

Fix up trivial conflict in arch/arm/kernel/signal.c.

It was due to the TIF_NOTIFY_RESUME addition in commit d0420c83f ("KEYS:
Extend TIF_NOTIFY_RESUME to (almost) all architectures") and follow-ups.
2009-09-14 17:48:14 -07:00
Russell King 87d721ad7a Merge branch 'master' into devel 2009-09-12 12:04:37 +01:00
Russell King ddd559b13f Merge branch 'devel-stable' into devel
Conflicts:
	MAINTAINERS
	arch/arm/mm/fault.c
2009-09-12 12:02:26 +01:00
Takashi Iwai e0b3032bcd Merge branch 'topic/asoc' into for-linus
* topic/asoc: (226 commits)
  ASoC: au1x: PSC-AC97 bugfixes
  ASoC: Fix WM835x Out4 capture enumeration
  ASoC: Remove unuused hw_read_t
  ASoC: fix pxa2xx-ac97.c breakage
  ASoC: Fully specify DC servo bits to update in wm_hubs
  ASoC: Debugged improper setting of PLL fields in WM8580 driver
  ASoC: new board driver to connect bfin-5xx with ad1836 codec
  ASoC: OMAP: Add functionality to set CLKR and FSR sources in McBSP DAI
  ASoC: davinci: i2c device creation moved into board files
  ASoC: Don't reconfigure WM8350 FLL if not needed
  ASoC: Fix s3c-i2s-v2 build
  ASoC: Make platform data optional for TLV320AIC3x
  ASoC: Add S3C24xx dependencies for Simtec machines
  ASoC: SDP3430: Fix TWL GPIO6 pin mux request
  ASoC: S3C platform: Fix s3c2410_dma_started() called at improper time
  ARM: OMAP: McBSP: Merge two functions into omap_mcbsp_start/_stop
  ASoC: OMAP: Fix setup of XCCR and RCCR registers in McBSP DAI
  OMAP: McBSP: Use textual values in DMA operating mode sysfs files
  ARM: OMAP: DMA: Add support for DMA channel self linking on OMAP1510
  ASoC: Select core DMA when building for S3C64xx
  ...
2009-09-10 15:32:40 +02:00
Tony Lindgren 1f685b36db Merge branch '2_6_32_for_next' of git://git.pwsan.com/linux-2.6 into for-next 2009-09-03 10:17:39 -07:00
Paul Walmsley 02bfc030e4 OMAP: omap_hwmod: call omap_hwmod init at boot; create interconnects
Connect the omap_hwmod code to the kernel boot.  Create some basic
interconnect and device structures for OMAP2/3 chips.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-09-03 20:14:05 +03:00
Paul Walmsley 63c8523841 OMAP2/3/4: create omap_hwmod layer
OMAP SoCs can be considered a collection of hardware IP blocks
connected by various interconnects.  The bus topology and device
integration data is somewhat more complex than platform_device can
encode.  This patch creates code and structures to manage information
about OMAP on-chip devices ("hardware modules") and their integration
to the rest of the chip.  Hardware module data is intended to be
generated dynamically from the TI hardware database for the OMAP4
chips and beyond, easing Linux support for new chip variants.

This code currently:

- resets and configures all hardware modules upon startup, reducing bootloader
  dependencies;

- provides hooks for Linux driver model code to enable, idle, and shutdown
  hardware modules (forthcoming patch);

- waits for hardware modules to leave idle once their clocks
  are enabled and OCP_SYSCONFIG bits are set appropriately.

- provides a means to pass arbitrary IP block configuration data (e.g.,
  FIFO size) to the device driver (via the dev_attr void pointer)

In the future this code is intended to:

- estimate interconnect bandwidth and latency characteristics to
  ensure constraints are satisfied during DVFS

- provide *GRPSEL bit data to the powerdomain code

- handle pin/ball muxing for devices

- generate IO mapping information dynamically

- supply device firewall configuration data

- provide hardware module data to other on-chip coprocessor software

- allow the removal of the "disable unused clocks" code in the OMAP2/3
  clock code

This patch represents a collaborative effort involving many people from TI,
Nokia, and the Linux-OMAP community.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Cc: Sakari Poussa <sakari.poussa@nokia.com>
Cc: Anand Sawant <sawant@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Eric Thomas <ethomas@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
2009-09-03 20:14:03 +03:00
Paul Walmsley b3c6df3ab2 OMAP2/3 board-*.c files: read bootloader configuration earlier
Most board-*.c files read configuration data from the bootloader in
their .init_machine() function.  This needs to happen earlier, at some
point before omap2_init_common_hw() is called.  This is because a
future patch will use the bootloader serial console port information
to enable the UART clocks earlier, immediately after omap2_clk_init().
This is in turn necessary since otherwise clock tree usecounts on
clocks like dpll4_m2x2_ck will be bogus, which can cause the
currently-active console UART clock to be disabled during boot.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-09-03 20:14:02 +03:00
Paul Walmsley 71348bcaac OMAP2/3/4 PRCM: add module IDLEST wait code
After a hardware module's clocks are enabled, Linux must wait for it
to indicate readiness via its IDLEST bit before attempting to access
the device, otherwise register accesses to the device may trigger an
abort.  This has traditionally been implemented in the clock
framework, but this is the wrong place for it: the clock framework
doesn't know which module clocks must be enabled for a module to leave
idle; and if a module is not in smart-idle mode, it may never leave
idle at all.  This type of information is best stored in a
per-hardware module data structure (coming in a following patch),
rather than a per-clock data structure.  The new code will use these new
functions to handle waiting for modules to enable.

Once hardware module data is filled in for all of the on-chip devices,
the clock framework code to handle IDLEST waiting can be removed.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-09-03 20:14:02 +03:00
Paul Walmsley c0407a96d0 OMAP2/3 PM: create the OMAP PM interface and add a default OMAP PM no-op layer
The interface provides device drivers, CPUFreq, and DSPBridge with a
means of controlling OMAP power management parameters that are not yet
supported by the Linux PM PMQoS interface.  Copious documentation is
in the patch in Documentation/arm/OMAP/omap_pm and the interface
header file, arch/arm/plat-omap/include/mach/omap-pm.h.

Thanks to Rajendra Nayak <rnayak@ti.com> for adding CORE (VDD2) OPP
support and moving the OPP table initialization earlier in the event
that the clock code needs them.  Thanks to Tero Kristo
<tero.kristo@nokia.com> for fixing the parameter check in
omap_pm_set_min_bus_tput().  Jouni signed off on Tero's patch.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Jouni Högander <jouni.hogander@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Igor Stoppa <igor.stoppa@nokia.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Anand Sawant <sawant@ti.com>
Cc: Sakari Poussa <sakari.poussa@nokia.com>
Cc: Veeramanikandan Raju <veera@ti.com>
Cc: Karthik Dasu <karthik-dp@ti.com>
2009-09-03 20:14:01 +03:00
Paul Walmsley 08e3d5f28d OMAP3 clock: remove superfluous calls to omap2_init_clk_clkdm
omap2_init_clk_clkdm() is called as part of the chip architecture-specific
initialization code, so calling it again from the struct clk init pointer
just wastes cycles.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-09-03 20:14:00 +03:00
Paul Walmsley 19f4d3a90b OMAP clock: associate MPU clocks with the mpu_clkdm
All MPU-related clocks should be in the mpu_clkdm.  This is needed for the
upcoming omap_hwmod patches, which needs to know the clockdomain that arm_fck
is in.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-09-03 20:14:00 +03:00
Sanjeev Premi 11b66383aa OMAP3 clock: Fixed processing of bootarg 'mpurate'
The argument 'mpurate' had no effect on the MPU
frequency. This patch fixes the same.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-09-03 20:13:58 +03:00
Paul Walmsley 5d113262ee OMAP: powerdomain: Fix overflow when doing powerdomain deps lookups.
At the end of the list pd is a pointer to a NULL struct, so checking
if the address == NULL doesn't help here. In fact the original code
will just keep running past the struct to read who knows what in
memory.

This case manifests itself when from clkdms_setup() when enabling auto
idle for a clock domain and the clockdomain usecount is greater than
0. When _clkdm_add_autodeps() tries to add the a dependency that does
not exist in the powerdomain->wkdep_srcs array the for loop will run
past the wkdep_srcs array.

Currently in linux-omap you won't hit this because the not found case
is never executed, unless you start modifying powerdomains and their
wakeup/sleep deps.

Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-09-03 20:13:53 +03:00
Tony Lindgren 5567fa1f54 Merge branch 'pm-upstream/debug' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into for-next 2009-09-02 15:23:05 -07:00
Tero Kristo 68d4778c70 OMAP: PM: Added suspend target state control to debugfs for OMAP3
Target state can be read / programmed via files under:
  [debugfs]/pm_debug/[pwrdm]/suspend

Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-09-02 15:08:25 -07:00
Tero Kristo 2811d6b323 OMAP: PM debug: Add PRCM register dump support
Allows dumping out current register contents from the debug filesystem, and
also allows user to add arbitrary register save points into code. Current
register contents are available under debugfs at:

[debugfs]/pm_debug/registers/current

To add a save point, do following:

From module init (or somewhere before the save call, called only once):
  pm_dbg_init_regset(n); // n=1..4, allocates memory for dump area #n

From arbitrary code location:
  pm_dbg_regset_save(n); // n=1..4, saves registers to dump area #n

After this, the register dump can be seen under [debugfs]/pm_debug/registers/n

Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-09-02 15:08:25 -07:00
Peter 'p2' De Schrijver 6199ab2690 OMAP: PM debug: make powerdomains use PM-debug counters
Make the powerdomain code call the new hook for updating the time.
Also implement the updated pwrdm_for_each.

Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-09-02 15:08:24 -07:00
Peter 'p2' De Schrijver 331b93f41d OMAP: PM: Add pm-debug counters
This patch provides the debugfs entries and a function which will be
called by the PM code to register the time spent per domain per
state. Also some new fields are added to the powerdomain struct to
keep the time information.

NOTE: As of v2.6.29, using getnstimeofday() after drivers are
suspended is no longer safe since the timekeeping subsystem is also
suspended as part of the suspend process.  Instead use sched_clock()
which on OMAP returns the 32k SYNC timer in nanoseconds.

Also, do not print out status for meta powerdomains (dpll*)

Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-09-02 15:08:24 -07:00
Peter 'p2' De Schrijver a23456e9b0 OMAP: PM: Add closures to clkdm_for_each and pwrdm_for_each.
Add some infrastructure to easily iterate over clock and power
domains.

Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-09-02 15:08:23 -07:00
Peter 'p2' De Schrijver fe617af716 OMAP: PM: Hook into PM counters
This patch modifies the clock, clockdomain and OMAP3 specific
powerdomain code to call the PM counter infrastructure whenever one or
more powerdomains might have changed state.

Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-09-02 15:08:23 -07:00
Peter 'p2' De Schrijver ba20bb1269 OMAP: PM counter infrastructure.
This patch provides the infrastructure to count how many times a
powerdomain entered a given power state (on, inactive, retention,
off). A number of functions are provided which will be called by the
chip specific powerdomain and clockdomain code whenever a transition
might have happened.

Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-09-02 15:08:23 -07:00
Ming Lei d3d381c636 OMAP3: PM: fix lockdep warning caused by omap3_pm_init
This patch uses kmalloc(size,GFP_ATOMIC) instead of kmalloc(size,GFP_KERNEL)
to allocate memory for instance of struct power_state in pwrdms_setup(),
since it may be called by pwrdm_for_each() with irq disabled.

It is a easy fix for the following lockdep warning caused by
kmalloc(size,GFP_KERNEL) in pwrdms_setup():

Power Management for TI OMAP3.
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:2282 lockdep_trace_alloc+0xe8/0xfc()
Modules linked in:
[<c0032ccc>] (unwind_backtrace+0x0/0xec) from [<c0056934>] (warn_slowpath_common+0x48/0x60)
[<c0056934>] (warn_slowpath_common+0x48/0x60) from [<c007da10>] (lockdep_trace_alloc+0xe8/0xfc)
[<c007da10>] (lockdep_trace_alloc+0xe8/0xfc) from [<c00cd9bc>] (kmem_cache_alloc+0x28/0x178)
[<c00cd9bc>] (kmem_cache_alloc+0x28/0x178) from [<c000f184>] (pwrdms_setup+0x30/0xf8)
[<c000f184>] (pwrdms_setup+0x30/0xf8) from [<c00381c4>] (pwrdm_for_each+0x64/0x84)
[<c00381c4>] (pwrdm_for_each+0x64/0x84) from [<c000ef60>] (omap3_pm_init+0x3f4/0x5ac)
[<c000ef60>] (omap3_pm_init+0x3f4/0x5ac) from [<c002c2c0>] (do_one_initcall+0x30/0x1d4)
[<c002c2c0>] (do_one_initcall+0x30/0x1d4) from [<c00088d8>] (kernel_init+0xa4/0x118)
[<c00088d8>] (kernel_init+0xa4/0x118) from [<c002ddf8>] (kernel_thread_exit+0x0/0x8)
---[ end trace 1e06f8d97dc5a19b ]---

Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-09-02 15:07:57 -07:00
Vikram Pandita 2fcc81a38b OMAP: Zoom2: release debug board detect gpio line
Release the Dbg board detection gpio once its purpose is served

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-09-02 15:07:56 -07:00
Reddy, Teerth 5110b2980a OMAP3: PM: add T2 interrupt line mux setting, and enable on 3430SDP
This patch changes for setting the padconf value for sys_nirq line
which is connected to T2 INTR1.  This will fix the T2 keypad wakeup
issue on OMAP3 SDP.

Signed-off-by: Teerth Reddy <teerth@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-09-02 15:07:56 -07:00
Anand Gadiyar bbde6ebae6 MUSB: Remove usb_musb_pm_init() call
In usb_musb_pm_init, we attempt to access an MUSB register
when the i-clock may not be on, or the module is otherwise
not accessible.

We need to either:
- enable the clock before this access, or
- remove this code and move it to the bootloader, or
- enable the clock in the bootloader

If we enable the clock in the bootloader, we might as well
add the workaround in the bootloader itself. This code will
anyway be changed once hwmod is in place, so remove it for now

This allows us to boot the kernel on certain OMAP3 boards with
a bootloader that doesn't enable this clock. Without this, we
will need to upgrade the bootloaders on these boards.

Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-09-02 15:07:56 -07:00
Vikram Pandita 24bcadb650 OMAP: Zoom2: update serial platform_data id for external UART
Now that on-chip UARTs each have separate platform_data, the external
UART needs an non-conflicting ID.  Since there are 3 on-chip UARTs,
the Zoom2 external UART will be registered after as the fourth.

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-09-02 15:07:55 -07:00
Santosh Shilimkar aae290fb4d ARM: OMAP4: Bypass the clock check.
Second reason of OMAP4 boot failure on 2.6.31.rc6, the UART
platform data is not getting registered to kernel.
Registration was failing because of clock check failure in
omap_serial_init().
Below patch fix the same.

OMAP4 clock framework patches are still getting discussed on mailing
list so till then we need this.

Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-09-02 15:07:54 -07:00
Santosh Shilimkar 0e3eaadfe3 ARM: OMAP4: Fix NULL pointer dereference crash.
After the patch series "[PATCH 00/14] OMAP PM fixes for .31-rc"
merge in 2.6.31-rc5, the kernel crashed during boot on OMAP4430.
This patch fixes it by adding UART4 support and related code.
Without this patch omap_serial_init() would produce " NULL pointer
dereference" and kernel crashes in the bootup on OMAP4430 platform.

Some more info on the merge issue can be found here.
More info- http://lkml.org/lkml/2009/8/20/192

Note: While merging this patch,"IO_ADDRESS" needs to be changed
to "OMAP2_IO_ADDRESS" if the Tony's below series is already merged in.
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg15072.html

Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-09-02 15:07:53 -07:00
Felipe Balbi bd04e46558 OMAP3: beagle: add missing twl4030 usb platform_data
without it twl4030_usb driver will not probe.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-08-28 11:24:15 -07:00