Add functionality for the power button on MX51 Babbage board.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently, only two operating points: 160Mhz and 800Mhz.
the operating points are tested on babbage 3.0
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
the attached patch allows SD to work on i.MX51 with Wolfram's drivers
Tested on i.MX51.
Based on original patch from: Richard Zhu <r65037@freescale.com>
Signed-off-by: Eric Bénard <eric@eukrea.com>
Versions of silicon older than TO3 have broken NEON implementation. Turn off
NEON in such cases.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Jason Hui <jason.hui@linaro.org>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Currently the uarts and timer only work because they are
turned on by reset default. Make them secondary clocks
of their corresponding peripheral clocks to make sure they
are turned on when necessary. Also, register some clocks
to get rid of compiler warnings
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A 2M bytes SPI NOR flash(sst25vf016b) is soldered on the mx51_3ds
board. So add the corresponding device for it.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested it by booting a rootfs via NFS.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
We can see MXC_CCM_CCGRx_MOD_OFF is defined as 0 while
MXC_CCM_CCGRx_CG_MASK is defined as 0x3 in crm_regs.h, here in the
_clk_ccgr_disable function, we want to clear the corresponding enable
bit fields to disable this clock, so we should choose MASK instead of
OFF otherwise clocks can't be disabled.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
CPUIMX51 is build around Freescale's i.MX515 and has up to
512MB of RAM, NAND Flash, Ethernet, USB Host with 4 ports
hub, USB OTG, ST16554 Quad UART on nCS1, I2C RTC ...
MBIMX51 adds LEDS, Keypad, TSC2007 touchscreen controler ...
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The commit 9a763bf "get rid of mxc_gpio_init" changed gpio_init
and irq_init sequence. Usually we will call set_irq_chained_handler
in gpio_init functions, this should be called after the irq_init
called, otherwise the chained irq can't get propoer irq_chip and this
irq will remain masked even we called set_irq_chained_handler.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX51 generates 2 IRQ for each GPIO bank : one for gpio 0 to 15
and one for gpio 16 to 31.
Actually only the lower IRQ is registered so register the second one.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add keymaps and imx_keypad device registration for imx51_3ds board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
add imx_keypad platform device definition and clocks for mx51
platforms.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
3-stack is a reference board from Freescale for their i.MX51 SoC.
Add board definition, Kconfig and Makefile to enable Freescale 3-stack
board.
Boot tested on a i.MX51 3-stack Rev2.0 board
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are some more conflicts than detected by git, namely support for
the newly added cpuimx machines needed to be converted to dynamic device
registration.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Conflicts:
arch/arm/mach-imx/Makefile
arch/arm/mach-imx/devices.c
arch/arm/mach-imx/devices.h
arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
arch/arm/mach-mx2/Kconfig
arch/arm/mach-mx25/Makefile
arch/arm/mach-mx25/devices.c
arch/arm/plat-mxc/include/mach/mx25.h
arch/arm/plat-mxc/include/mach/mxc_nand.h
The pads capable of being used as GPIOs had their pad-name and mode-name
switched. Also, fix the following:
- Whitespace fixes
- Replace IOMUX_CONFIG_ALTn with 'n'
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This function is defined once for each imx family and so is in the way
when compiling a kernel for more than one SoC.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This patch de-asserts the reset line that is connected to the USB
ULPI PHY on USB Host1.
This patch should be included with the original USB host enablement
set of patches of mx51 babbage hw, but was accidentily left out.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch enables usb gadget for freescale mx51 babbage hw. By default,
the OTG port will be in device mode. To put the OTG port into Host mode,
pass "otg_mode=host" in the exec command.
This patch applies to 2.6.34-rc7.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Russell King