The calling conventions for __d_lookup_rcu() and dentry_cmp() are
annoying in different ways, and there is actually one single underlying
reason for both of the annoyances.
The fundamental reason is that we do the returned dentry sequence number
check inside __d_lookup_rcu() instead of doing it in the caller. This
results in two annoyances:
- __d_lookup_rcu() now not only needs to return the dentry and the
sequence number that goes along with the lookup, it also needs to
return the inode pointer that was validated by that sequence number
check.
- and because we did the sequence number check early (to validate the
name pointer and length) we also couldn't just pass the dentry itself
to dentry_cmp(), we had to pass the counted string that contained the
name.
So that sequence number decision caused two separate ugly calling
conventions.
Both of these problems would be solved if we just did the sequence
number check in the caller instead. There's only one caller, and that
caller already has to do the sequence number check for the parent
anyway, so just do that.
That allows us to stop returning the dentry->d_inode in that in-out
argument (pointer-to-pointer-to-inode), so we can make the inode
argument just a regular input inode pointer. The caller can just load
the inode from dentry->d_inode, and then do the sequence number check
after that to make sure that it's synchronized with the name we looked
up.
And it allows us to just pass in the dentry to dentry_cmp(), which is
what all the callers really wanted. Sure, dentry_cmp() has to be a bit
careful about the dentry (which is not stable during RCU lookup), but
that's actually very simple.
And now that dentry_cmp() can clearly see that the first string argument
is a dentry, we can use the direct word access for that, instead of the
careful unaligned zero-padding. The dentry name is always properly
aligned, since it is a single path component that is either embedded
into the dentry itself, or was allocated with kmalloc() (see __d_alloc).
Finally, this also uninlines the nasty slow-case for dentry comparisons:
that one *does* need to do a sequence number check, since it will call
in to the low-level filesystems, and we want to give those a stable
inode pointer and path component length/start arguments. Doing an extra
sequence check for that slow case is not a problem, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's only used inside fs/dcache.c, and we're going to play games with it
for the word-at-a-time patches. This time we really don't even want to
export it, because it really is an internal function to fs/dcache.c, and
has been since it was introduced.
Having it in that extremely hot header file (it's included in pretty
much everything, thanks to <linux/fs.h>) is a disaster for testing
different versions, and is utterly pointless.
We really should have some kind of header file diet thing, where we
figure out which parts of header files are really better off private and
only result in more expensive compiles.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It did some odd things for unclear reasons. As this is one of the
functions that gets changed when doing word-at-a-time compares, this is
yet another of the "don't change any semantics, but clean things up so
that subsequent patches don't get obscured by the cleanups".
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
.. and also use it in lookup_one_len() rather than open-coding it.
There aren't any performance-critical users, so inlining it is silly.
But it wouldn't matter if it wasn't for the fact that the word-at-a-time
dentry name patches want to conditionally replace the function, and
uninlining it sets the stage for that.
So again, this is a preparatory patch that doesn't change any semantics,
and only prepares for a much cleaner and testable word-at-a-time dentry
name accessor patch.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These don't change any semantics, but they clean up the code a bit and
mark some arguments appropriately 'const'.
They came up as I was doing the word-at-a-time dcache name accessor
code, and cleaning this up now allows me to send out a smaller relevant
interesting patch for the experimental stuff.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: ensure prealloc_blob is in place when removing xattr
rbd: initialize snap_rwsem in rbd_add()
ceph: enable/disable dentry complete flags via mount option
vfs: export symbol d_find_any_alias()
ceph: always initialize the dentry in open_root_dentry()
libceph: remove useless return value for osd_client __send_request()
ceph: avoid iput() while holding spinlock in ceph_dir_fsync
ceph: avoid useless dget/dput in encode_fh
ceph: dereference pointer after checking for NULL
crush: fix force for non-root TAKE
ceph: remove unnecessary d_fsdata conditional checks
ceph: Use kmemdup rather than duplicating its implementation
Fix up conflicts in fs/ceph/super.c (d_alloc_root() failure handling vs
always initialize the dentry in open_root_dentry)
Two (or more) concurrent calls of shrink_dcache_parent() on the same dentry may
cause shrink_dcache_parent() to loop forever.
Here's what appears to happen:
1 - CPU0: select_parent(P) finds C and puts it on dispose list, returns 1
2 - CPU1: select_parent(P) locks P->d_lock
3 - CPU0: shrink_dentry_list() locks C->d_lock
dentry_kill(C) tries to lock P->d_lock but fails, unlocks C->d_lock
4 - CPU1: select_parent(P) locks C->d_lock,
moves C from dispose list being processed on CPU0 to the new
dispose list, returns 1
5 - CPU0: shrink_dentry_list() finds dispose list empty, returns
6 - Goto 2 with CPU0 and CPU1 switched
Basically select_parent() steals the dentry from shrink_dentry_list() and thinks
it found a new one, causing shrink_dentry_list() to think it's making progress
and loop over and over.
One way to trigger this is to make udev calls stat() on the sysfs file while it
is going away.
Having a file in /lib/udev/rules.d/ with only this one rule seems to the trick:
ATTR{vendor}=="0x8086", ATTR{device}=="0x10ca", ENV{PCI_SLOT_NAME}="%k", ENV{MATCHADDR}="$attr{address}", RUN+="/bin/true"
Then execute the following loop:
while true; do
echo -bond0 > /sys/class/net/bonding_masters
echo +bond0 > /sys/class/net/bonding_masters
echo -bond1 > /sys/class/net/bonding_masters
echo +bond1 > /sys/class/net/bonding_masters
done
One fix would be to check all callers and prevent concurrent calls to
shrink_dcache_parent(). But I think a better solution is to stop the
stealing behavior.
This patch adds a new dentry flag that is set when the dentry is added to the
dispose list. The flag is cleared in dentry_lru_del() in case the dentry gets a
new reference just before being pruned.
If the dentry has this flag, select_parent() will skip it and let
shrink_dentry_list() retry pruning it. With select_parent() skipping those
dentries there will not be the appearance of progress (new dentries found) when
there is none, hence shrink_dcache_parent() will not loop forever.
Set the flag is also set in prune_dcache_sb() for consistency as suggested by
Linus.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
__d_path() API is asking for trouble and in case of apparmor d_namespace_path()
getting just that. The root cause is that when __d_path() misses the root
it had been told to look for, it stores the location of the most remote ancestor
in *root. Without grabbing references. Sure, at the moment of call it had
been pinned down by what we have in *path. And if we raced with umount -l, we
could have very well stopped at vfsmount/dentry that got freed as soon as
prepend_path() dropped vfsmount_lock.
It is safe to compare these pointers with pre-existing (and known to be still
alive) vfsmount and dentry, as long as all we are asking is "is it the same
address?". Dereferencing is not safe and apparmor ended up stepping into
that. d_namespace_path() really wants to examine the place where we stopped,
even if it's not connected to our namespace. As the result, it looked
at ->d_sb->s_magic of a dentry that might've been already freed by that point.
All other callers had been careful enough to avoid that, but it's really
a bad interface - it invites that kind of trouble.
The fix is fairly straightforward, even though it's bigger than I'd like:
* prepend_path() root argument becomes const.
* __d_path() is never called with NULL/NULL root. It was a kludge
to start with. Instead, we have an explicit function - d_absolute_root().
Same as __d_path(), except that it doesn't get root passed and stops where
it stops. apparmor and tomoyo are using it.
* __d_path() returns NULL on path outside of root. The main
caller is show_mountinfo() and that's precisely what we pass root for - to
skip those outside chroot jail. Those who don't want that can (and do)
use d_path().
* __d_path() root argument becomes const. Everyone agrees, I hope.
* apparmor does *NOT* try to use __d_path() or any of its variants
when it sees that path->mnt is an internal vfsmount. In that case it's
definitely not mounted anywhere and dentry_path() is exactly what we want
there. Handling of sysctl()-triggered weirdness is moved to that place.
* if apparmor is asked to do pathname relative to chroot jail
and __d_path() tells it we it's not in that jail, the sucker just calls
d_absolute_path() instead. That's the other remaining caller of __d_path(),
BTW.
* seq_path_root() does _NOT_ return -ENAMETOOLONG (it's stupid anyway -
the normal seq_file logics will take care of growing the buffer and redoing
the call of ->show() just fine). However, if it gets path not reachable
from root, it returns SEQ_SKIP. The only caller adjusted (i.e. stopped
ignoring the return value as it used to do).
Reviewed-by: John Johansen <john.johansen@canonical.com>
ACKed-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
This adds a d_prune dentry operation that is called by the VFS prior to
pruning (i.e. unhashing and killing) a hashed dentry from the dcache.
Wrap dentry_lru_del() and use the new _prune() helper in the cases where we
are about to unhash and kill the dentry.
This will be used by Ceph to maintain a flag indicating whether the
complete contents of a directory are contained in the dcache, allowing it
to satisfy lookups and readdir without addition server communication.
Renumber a few DCACHE_* #defines to group DCACHE_OP_PRUNE with the other
DCACHE_OP_ bits.
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Gcc tends to generate better code with small integers, including the
DCACHE_xyz flag tests - so move the common ones to be first in the list.
Also just remove the unused DCACHE_INOTIFY_PARENT_WATCHED and
DCACHE_AUTOFS_PENDING values, their users no longer exists in the source
tree.
And add a "unlikely()" to the DCACHE_OP_COMPARE test, since we want the
common case to be a nice straight-line fall-through.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Btrfs (and I'd venture most other fs's) stores its indexes in nice disk order
for readdir, but unfortunately in the case of anything that stats the files in
order that readdir spits back (like oh say ls) that means we still have to do
the normal lookup of the file, which means looking up our other index and then
looking up the inode. What I want is a way to create dummy dentries when we
find them in readdir so that when ls or anything else subsequently does a
stat(), we already have the location information in the dentry and can go
straight to the inode itself. The lookup stuff just assumes that if it finds a
dentry it is done, it doesn't perform a lookup. So add a DCACHE_NEED_LOOKUP
flag so that the lookup code knows it still needs to run i_op->lookup() on the
parent to get the inode for the dentry. I have tested this with btrfs and I
went from something that looks like this
http://people.redhat.com/jwhiter/ls-noreada.png
To this
http://people.redhat.com/jwhiter/ls-good.png
Thats a savings of 1300 seconds, or 22 minutes. That is a significant savings.
Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The dentry hashing rules have been really quite complicated for a long
while, in odd ways. That made functions like __d_drop() very fragile
and non-obvious.
In particular, whether a dentry was hashed or not was indicated with an
explicit DCACHE_UNHASHED bit. That's despite the fact that the hash
abstraction that the dentries use actually have a 'is this entry hashed
or not' model (which is a simple test of the 'pprev' pointer).
The reason that was done is because we used the normal 'is this entry
unhashed' model to mark whether the dentry had _ever_ been hashed in the
dentry hash tables, and that logic goes back many years (commit
b3423415fbc2: "dcache: avoid RCU for never-hashed dentries").
That, in turn, meant that __d_drop had totally different unhashing logic
for the dentry hash table case and for the anonymous dcache case,
because in order to use the "is this dentry hashed" logic as a flag for
whether it had ever been on the RCU hash table, we had to unhash such a
dentry differently so that we'd never think that it wasn't 'unhashed'
and wouldn't be free'd correctly.
That's just insane. It made the logic really hard to follow, when there
were two different kinds of "unhashed" states, and one of them (the one
that used "list_bl_unhashed()") really had nothing at all to do with
being unhashed per se, but with a very subtle lifetime rule instead.
So turn all of it around, and make it logical.
Instead of having a DENTRY_UNHASHED bit in d_flags to indicate whether
the dentry is on the hash chains or not, use the hash chain unhashed
logic for that. Suddenly "d_unhashed()" just uses "list_bl_unhashed()",
and everything makes sense.
And for the lifetime rule, just use an explicit DENTRY_RCUACCEES bit.
If we ever insert the dentry into the dentry hash table so that it is
visible to RCU lookup, we mark it DENTRY_RCUACCESS to show that it now
needs the RCU lifetime rules. Now suddently that test at dentry free
time makes sense too.
And because unhashing now is sane and doesn't depend on where the dentry
got unhashed from (because the dentry hash chain details doesn't have
some subtle side effects), we can re-unify the __d_drop() logic and use
common code for the unhashing.
Also fix one more open-coded hash chain bit_spin_lock() that I missed in
the previous chain locking cleanup commit.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lookup_mnt() is only used in the core fs routines now, so it doesn't need to
be globally declared anymore. It isn't exported to modules at the moment, so
nothing that can be modularised seems to be using it.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Allow d_manage() to be called from pathwalk when it is in RCU-walk mode as well
as when it is in Ref-walk mode. This permits __follow_mount_rcu() to call
d_manage() directly. d_manage() needs a parameter to indicate that it is in
RCU-walk mode as it isn't allowed to sleep if in that mode (but should return
-ECHILD instead).
autofs4_d_manage() can then be set to retain RCU-walk mode if the daemon
accesses it and otherwise request dropping back to ref-walk mode.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add a dentry op (d_manage) to permit a filesystem to hold a process and make it
sleep when it tries to transit away from one of that filesystem's directories
during a pathwalk. The operation is keyed off a new dentry flag
(DCACHE_MANAGE_TRANSIT).
The filesystem is allowed to be selective about which processes it holds and
which it permits to continue on or prohibits from transiting from each flagged
directory. This will allow autofs to hold up client processes whilst letting
its userspace daemon through to maintain the directory or the stuff behind it
or mounted upon it.
The ->d_manage() dentry operation:
int (*d_manage)(struct path *path, bool mounting_here);
takes a pointer to the directory about to be transited away from and a flag
indicating whether the transit is undertaken by do_add_mount() or
do_move_mount() skipping through a pile of filesystems mounted on a mountpoint.
It should return 0 if successful and to let the process continue on its way;
-EISDIR to prohibit the caller from skipping to overmounted filesystems or
automounting, and to use this directory; or some other error code to return to
the user.
->d_manage() is called with namespace_sem writelocked if mounting_here is true
and no other locks held, so it may sleep. However, if mounting_here is true,
it may not initiate or wait for a mount or unmount upon the parameter
directory, even if the act is actually performed by userspace.
Within fs/namei.c, follow_managed() is extended to check with d_manage() first
on each managed directory, before transiting away from it or attempting to
automount upon it.
follow_down() is renamed follow_down_one() and should only be used where the
filesystem deliberately intends to avoid management steps (e.g. autofs).
A new follow_down() is added that incorporates the loop done by all other
callers of follow_down() (do_add/move_mount(), autofs and NFSD; whilst AFS, NFS
and CIFS do use it, their use is removed by converting them to use
d_automount()). The new follow_down() calls d_manage() as appropriate. It
also takes an extra parameter to indicate if it is being called from mount code
(with namespace_sem writelocked) which it passes to d_manage(). follow_down()
ignores automount points so that it can be used to mount on them.
__follow_mount_rcu() is made to abort rcu-walk mode if it hits a directory with
DCACHE_MANAGE_TRANSIT set on the basis that we're probably going to have to
sleep. It would be possible to enter d_manage() in rcu-walk mode too, and have
that determine whether to abort or not itself. That would allow the autofs
daemon to continue on in rcu-walk mode.
Note that DCACHE_MANAGE_TRANSIT on a directory should be cleared when it isn't
required as every tranist from that directory will cause d_manage() to be
invoked. It can always be set again when necessary.
==========================
WHAT THIS MEANS FOR AUTOFS
==========================
Autofs currently uses the lookup() inode op and the d_revalidate() dentry op to
trigger the automounting of indirect mounts, and both of these can be called
with i_mutex held.
autofs knows that the i_mutex will be held by the caller in lookup(), and so
can drop it before invoking the daemon - but this isn't so for d_revalidate(),
since the lock is only held on _some_ of the code paths that call it. This
means that autofs can't risk dropping i_mutex from its d_revalidate() function
before it calls the daemon.
The bug could manifest itself as, for example, a process that's trying to
validate an automount dentry that gets made to wait because that dentry is
expired and needs cleaning up:
mkdir S ffffffff8014e05a 0 32580 24956
Call Trace:
[<ffffffff885371fd>] :autofs4:autofs4_wait+0x674/0x897
[<ffffffff80127f7d>] avc_has_perm+0x46/0x58
[<ffffffff8009fdcf>] autoremove_wake_function+0x0/0x2e
[<ffffffff88537be6>] :autofs4:autofs4_expire_wait+0x41/0x6b
[<ffffffff88535cfc>] :autofs4:autofs4_revalidate+0x91/0x149
[<ffffffff80036d96>] __lookup_hash+0xa0/0x12f
[<ffffffff80057a2f>] lookup_create+0x46/0x80
[<ffffffff800e6e31>] sys_mkdirat+0x56/0xe4
versus the automount daemon which wants to remove that dentry, but can't
because the normal process is holding the i_mutex lock:
automount D ffffffff8014e05a 0 32581 1 32561
Call Trace:
[<ffffffff80063c3f>] __mutex_lock_slowpath+0x60/0x9b
[<ffffffff8000ccf1>] do_path_lookup+0x2ca/0x2f1
[<ffffffff80063c89>] .text.lock.mutex+0xf/0x14
[<ffffffff800e6d55>] do_rmdir+0x77/0xde
[<ffffffff8005d229>] tracesys+0x71/0xe0
[<ffffffff8005d28d>] tracesys+0xd5/0xe0
which means that the system is deadlocked.
This patch allows autofs to hold up normal processes whilst the daemon goes
ahead and does things to the dentry tree behind the automouter point without
risking a deadlock as almost no locks are held in d_manage() and none in
d_automount().
Signed-off-by: David Howells <dhowells@redhat.com>
Was-Acked-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add a dentry op (d_automount) to handle automounting directories rather than
abusing the follow_link() inode operation. The operation is keyed off a new
dentry flag (DCACHE_NEED_AUTOMOUNT).
This also makes it easier to add an AT_ flag to suppress terminal segment
automount during pathwalk and removes the need for the kludge code in the
pathwalk algorithm to handle directories with follow_link() semantics.
The ->d_automount() dentry operation:
struct vfsmount *(*d_automount)(struct path *mountpoint);
takes a pointer to the directory to be mounted upon, which is expected to
provide sufficient data to determine what should be mounted. If successful, it
should return the vfsmount struct it creates (which it should also have added
to the namespace using do_add_mount() or similar). If there's a collision with
another automount attempt, NULL should be returned. If the directory specified
by the parameter should be used directly rather than being mounted upon,
-EISDIR should be returned. In any other case, an error code should be
returned.
The ->d_automount() operation is called with no locks held and may sleep. At
this point the pathwalk algorithm will be in ref-walk mode.
Within fs/namei.c itself, a new pathwalk subroutine (follow_automount()) is
added to handle mountpoints. It will return -EREMOTE if the automount flag was
set, but no d_automount() op was supplied, -ELOOP if we've encountered too many
symlinks or mountpoints, -EISDIR if the walk point should be used without
mounting and 0 if successful. The path will be updated to point to the mounted
filesystem if a successful automount took place.
__follow_mount() is replaced by follow_managed() which is more generic
(especially with the patch that adds ->d_manage()). This handles transits from
directories during pathwalk, including automounting and skipping over
mountpoints (and holding processes with the next patch).
__follow_mount_rcu() will jump out of RCU-walk mode if it encounters an
automount point with nothing mounted on it.
follow_dotdot*() does not handle automounts as you don't want to trigger them
whilst following "..".
I've also extracted the mount/don't-mount logic from autofs4 and included it
here. It makes the mount go ahead anyway if someone calls open() or creat(),
tries to traverse the directory, tries to chdir/chroot/etc. into the directory,
or sticks a '/' on the end of the pathname. If they do a stat(), however,
they'll only trigger the automount if they didn't also say O_NOFOLLOW.
I've also added an inode flag (S_AUTOMOUNT) so that filesystems can mark their
inodes as automount points. This flag is automatically propagated to the
dentry as DCACHE_NEED_AUTOMOUNT by __d_instantiate(). This saves NFS and could
save AFS a private flag bit apiece, but is not strictly necessary. It would be
preferable to do the propagation in d_set_d_op(), but that doesn't normally
have access to the inode.
[AV: fixed breakage in case if __follow_mount_rcu() fails and nameidata_drop_rcu()
succeeds in RCU case of do_lookup(); we need to fall through to non-RCU case after
that, rather than just returning with ungrabbed *path]
Signed-off-by: David Howells <dhowells@redhat.com>
Was-Acked-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix new kernel-doc notation warning in dcache.h:
Warning(include/linux/dcache.h:316): Excess function parameter 'Returns' description in '__d_rcu_to_refcount'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The standard memcmp function on a Westmere system shows up hot in
profiles in the `git diff` workload (both parallel and single threaded),
and it is likely due to the costs associated with trapping into
microcode, and little opportunity to improve memory access (dentry
name is not likely to take up more than a cacheline).
So replace it with an open-coded byte comparison. This increases code
size by 8 bytes in the critical __d_lookup_rcu function, but the
speedup is huge, averaging 10 runs of each:
git diff st user sys elapsed CPU
before 1.15 2.57 3.82 97.1
after 1.14 2.35 3.61 96.8
git diff mt user sys elapsed CPU
before 1.27 3.85 1.46 349
after 1.26 3.54 1.43 333
Elapsed time for single threaded git diff at 95.0% confidence:
-0.21 +/- 0.01
-5.45% +/- 0.24%
It's -0.66% +/- 0.06% elapsed time on my Opteron, so rep cmp costs on the
fam10h seem to be relatively smaller, but there is still a win.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Regardless of how much we possibly try to scale dcache, there is likely
always going to be some fundamental contention when adding or removing children
under the same parent. Pseudo filesystems do not seem need to have connected
dentries because by definition they are disconnected.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
dcache_inode_lock can be replaced with per-inode locking. Use existing
inode->i_lock for this. This is slightly non-trivial because we sometimes
need to find the inode from the dentry, which requires d_inode to be
stabilised (either with refcount or d_lock).
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Require filesystems be aware of .d_revalidate being called in rcu-walk
mode (nd->flags & LOOKUP_RCU). For now do a simple push down, returning
-ECHILD from all implementations.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Put dentry and inode fields into top of data structure. This allows RCU path
traversal to perform an RCU dentry lookup in a path walk by touching only the
first 56 bytes of the dentry.
We also fit in 8 bytes of inline name in the first 64 bytes, so for short
names, only 64 bytes needs to be touched to perform the lookup. We should
get rid of the hash->prev pointer from the first 64 bytes, and fit 16 bytes
of name in there, which will take care of 81% rather than 32% of the kernel
tree.
inode is also rearranged so that RCU lookup will only touch a single cacheline
in the inode, plus one in the i_ops structure.
This is important for directory component lookups in RCU path walking. In the
kernel source, directory names average is around 6 chars, so this works.
When we reach the last element of the lookup, we need to lock it and take its
refcount which requires another cacheline access.
Align dentry and inode operations structs, so members will be at predictable
offsets and we can group common operations into head of structure.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Reduce some branches and memory accesses in dcache lookup by adding dentry
flags to indicate common d_ops are set, rather than having to check them.
This saves a pointer memory access (dentry->d_op) in common path lookup
situations, and saves another pointer load and branch in cases where we
have d_op but not the particular operation.
Patched with:
git grep -E '[.>]([[:space:]])*d_op([[:space:]])*=' | xargs sed -e 's/\([^\t ]*\)->d_op = \(.*\);/d_set_d_op(\1, \2);/' -e 's/\([^\t ]*\)\.d_op = \(.*\);/d_set_d_op(\&\1, \2);/' -i
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Rather than keep a d_mounted count in the dentry, set a dentry flag instead.
The flag can be cleared by checking the hash table to see if there are any
mounts left, which is not time critical because it is performed at detach time.
The mounted state of a dentry is only used to speculatively take a look in the
mount hash table if it is set -- before following the mount, vfsmount lock is
taken and mount re-checked without races.
This saves 4 bytes on 32-bit, nothing on 64-bit but it does provide a hole I
might use later (and some configs have larger than 32-bit spinlocks which might
make use of the hole).
Autofs4 conversion and changelog by Ian Kent <raven@themaw.net>:
In autofs4, when expring direct (or offset) mounts we need to ensure that we
block user path walks into the autofs mount, which is covered by another mount.
To do this we clear the mounted status so that follows stop before walking into
the mount and are essentially blocked until the expire is completed. The
automount daemon still finds the correct dentry for the umount due to the
follow mount logic in fs/autofs4/root.c:autofs4_follow_link(), which is set as
an inode operation for direct and offset mounts only and is called following
the lookup that stopped at the covered mount.
At the end of the expire the covering mount probably has gone away so the
mounted status need not be restored. But we need to check this and only restore
the mounted status if the expire failed.
XXX: autofs may not work right if we have other mounts go over the top of it?
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Perform common cases of path lookups without any stores or locking in the
ancestor dentry elements. This is called rcu-walk, as opposed to the current
algorithm which is a refcount based walk, or ref-walk.
This results in far fewer atomic operations on every path element,
significantly improving path lookup performance. It also avoids cacheline
bouncing on common dentries, significantly improving scalability.
The overall design is like this:
* LOOKUP_RCU is set in nd->flags, which distinguishes rcu-walk from ref-walk.
* Take the RCU lock for the entire path walk, starting with the acquiring
of the starting path (eg. root/cwd/fd-path). So now dentry refcounts are
not required for dentry persistence.
* synchronize_rcu is called when unregistering a filesystem, so we can
access d_ops and i_ops during rcu-walk.
* Similarly take the vfsmount lock for the entire path walk. So now mnt
refcounts are not required for persistence. Also we are free to perform mount
lookups, and to assume dentry mount points and mount roots are stable up and
down the path.
* Have a per-dentry seqlock to protect the dentry name, parent, and inode,
so we can load this tuple atomically, and also check whether any of its
members have changed.
* Dentry lookups (based on parent, candidate string tuple) recheck the parent
sequence after the child is found in case anything changed in the parent
during the path walk.
* inode is also RCU protected so we can load d_inode and use the inode for
limited things.
* i_mode, i_uid, i_gid can be tested for exec permissions during path walk.
* i_op can be loaded.
When we reach the destination dentry, we lock it, recheck lookup sequence,
and increment its refcount and mountpoint refcount. RCU and vfsmount locks
are dropped. This is termed "dropping rcu-walk". If the dentry refcount does
not match, we can not drop rcu-walk gracefully at the current point in the
lokup, so instead return -ECHILD (for want of a better errno). This signals the
path walking code to re-do the entire lookup with a ref-walk.
Aside from the final dentry, there are other situations that may be encounted
where we cannot continue rcu-walk. In that case, we drop rcu-walk (ie. take
a reference on the last good dentry) and continue with a ref-walk. Again, if
we can drop rcu-walk gracefully, we return -ECHILD and do the whole lookup
using ref-walk. But it is very important that we can continue with ref-walk
for most cases, particularly to avoid the overhead of double lookups, and to
gain the scalability advantages on common path elements (like cwd and root).
The cases where rcu-walk cannot continue are:
* NULL dentry (ie. any uncached path element)
* parent with d_inode->i_op->permission or ACLs
* dentries with d_revalidate
* Following links
In future patches, permission checks and d_revalidate become rcu-walk aware. It
may be possible eventually to make following links rcu-walk aware.
Uncached path elements will always require dropping to ref-walk mode, at the
very least because i_mutex needs to be grabbed, and objects allocated.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
dget_locked was a shortcut to avoid the lazy lru manipulation when we already
held dcache_lock (lru manipulation was relatively cheap at that point).
However, how that the lru lock is an innermost one, we never hold it at any
caller, so the lock cost can now be avoided. We already have well working lazy
dcache LRU, so it should be fine to defer LRU manipulations to scan time.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
The remaining usages for dcache_lock is to allow atomic, multi-step read-side
operations over the directory tree by excluding modifications to the tree.
Also, to walk in the leaf->root direction in the tree where we don't have
a natural d_lock ordering.
This could be accomplished by taking every d_lock, but this would mean a
huge number of locks and actually gets very tricky.
Solve this instead by using the rename seqlock for multi-step read-side
operations, retry in case of a rename so we don't walk up the wrong parent.
Concurrent dentry insertions are not serialised against. Concurrent deletes
are tricky when walking up the directory: our parent might have been deleted
when dropping locks so also need to check and retry for that.
We can also use the rename lock in cases where livelock is a worry (and it
is introduced in subsequent patch).
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Add a new lock, dcache_inode_lock, to protect the inode's i_dentry list
from concurrent modification. d_alias is also protected by d_lock.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Protect d_subdirs and d_child with d_lock, except in filesystems that aren't
using dcache_lock for these anyway (eg. using i_mutex).
Note: if we change the locking rule in future so that ->d_child protection is
provided only with ->d_parent->d_lock, it may allow us to reduce some locking.
But it would be an exception to an otherwise regular locking scheme, so we'd
have to see some good results. Probably not worthwhile.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Make d_count non-atomic and protect it with d_lock. This allows us to ensure a
0 refcount dentry remains 0 without dcache_lock. It is also fairly natural when
we start protecting many other dentry members with d_lock.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Add a new lock, dcache_hash_lock, to protect the dcache hash table from
concurrent modification. d_hash is also protected by d_lock.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Remove dcache_lock locking from hostfs filesystem, and move it into dcache
helpers. All that is required is a coherent path name. Protection from
concurrent modification of the namespace after path name generation is not
provided in current code, because dcache_lock is dropped before the path is
used.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Change d_hash so it may be called from lock-free RCU lookups. See similar
patch for d_compare for details.
For in-tree filesystems, this is just a mechanical change.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Change d_compare so it may be called from lock-free RCU lookups. This
does put significant restrictions on what may be done from the callback,
however there don't seem to have been any problems with in-tree fses.
If some strange use case pops up that _really_ cannot cope with the
rcu-walk rules, we can just add new rcu-unaware callbacks, which would
cause name lookup to drop out of rcu-walk mode.
For in-tree filesystems, this is just a mechanical change.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
smpfs and ncpfs want to update a live dentry name in-place. Rather than
have them open code the locking, provide a documented dcache API.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Change d_delete from a dentry deletion notification to a dentry caching
advise, more like ->drop_inode. Require it to be constant and idempotent,
and not take d_lock. This is how all existing filesystems use the callback
anyway.
This makes fine grained dentry locking of dput and dentry lru scanning
much simpler.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Remove redundant (and incorrect, since dcache RCU lookup) dentry locking
documentation and point to the canonical document.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Prepend "(unreachable)" to path strings if the path is not reachable
from the current root.
Two places updated are
- the return string from getcwd()
- and symlinks under /proc/$PID.
Other uses of d_path() are left unchanged (we know that some old
software crashes if /proc/mounts is changed).
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
builds path relative to fs root, called under dcache_lock,
doesn't append any nonsense to unlinked ones.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
1) i_flags simply doesn't work for mount/unlink race prevention;
we may have many links to file and rm on one of those obviously
shouldn't prevent bind on top of another later on. To fix it
right way we need to mark _dentry_ as unsuitable for mounting
upon; new flag (DCACHE_CANT_MOUNT) is protected by d_flags and
i_mutex on the inode in question. Set it (with dont_mount(dentry))
in unlink/rmdir/etc., check (with cant_mount(dentry)) in places
in namespace.c that used to check for S_DEAD. Setting S_DEAD
is still needed in places where we used to set it (for directories
getting killed), since we rely on it for readdir/rmdir race
prevention.
2) rename()/mount() protection has another bogosity - we unhash
the target before we'd checked that it's not a mountpoint. Fixed.
3) ancient bogosity in pivot_root() - we locked i_mutex on the
right directory, but checked S_DEAD on the different (and wrong)
one. Noticed and fixed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
d_unlinked() will be used in middle-term to ban checkpointing when opened
but unlinked file is detected, and in long term, to detect such situation
and special case on it.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
inotify and dnotify both use a similar parent notification mechanism. We
add a generic parent notification mechanism to fsnotify for both of these
to use. This new machanism also adds the dentry flag optimization which
exists for inotify to dnotify.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
This change will allow for tagging many dentry_operations const in the
source tree.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
struct dentry is one of the most critical structures in the kernel. So it's
sad to see it going neglected.
With CONFIG_PROFILING turned on (which is probably the common case at least
for distros and kernel developers), sizeof(struct dcache) == 208 here
(64-bit). This gives 19 objects per slab.
I packed d_mounted into a hole, and took another 4 bytes off the inline
name length to take the padding out from the end of the structure. This
shinks it to 200 bytes. I could have gone the other way and increased the
length to 40, but I'm aiming for a magic number, read on...
I then got rid of the d_cookie pointer. This shrinks it to 192 bytes. Rant:
why was this ever a good idea? The cookie system should increase its hash
size or use a tree or something if lookups are a problem. Also the "fast
dcookie lookups" in oprofile should be moved into the dcookie code -- how
can oprofile possibly care about the dcookie_mutex? It gets dropped after
get_dcookie() returns so it can't be providing any sort of protection.
At 192 bytes, 21 objects fit into a 4K page, saving about 3MB on my system
with ~140 000 entries allocated. 192 is also a multiple of 64, so we get
nice cacheline alignment on 64 and 32 byte line systems -- any given dentry
will now require 3 cachelines to touch all fields wheras previously it
would require 4.
I know the inline name size was chosen quite carefully, however with the
reduction in cacheline footprint, it should actually be just about as fast
to do a name lookup for a 36 character name as it was before the patch (and
faster for other sizes). The memory footprint savings for names which are
<= 32 or > 36 bytes long should more than make up for the memory cost for
33-36 byte names.
Performance is a feature...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This adds d_ancestor() instead of d_isparent(), then use it.
If new_dentry == old_dentry, is_subdir() returns 1, looks strange.
"new_dentry == old_dentry" is not subdir obviously. But I'm not
checking callers for now, so this keeps current behavior.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
The calling conventions of d_alloc_anon are rather unfortunate for all
users, and it's name is not very descriptive either.
Add d_obtain_alias as a new exported helper that drops the inode
reference in the failure case, too and allows to pass-through NULL
pointers and inodes to allow for tail-calls in the export operations.
Incidentally this helper already existed as a private function in
libfs.c as exportfs_d_alloc so kill that one and switch the callers
to d_obtain_alias.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
As pointed out during review d_add_ci argument order should match d_add,
so switch the dentry and inode arguments.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This add a dcache entry to the dcache for lookup, but changing the name
that is associated with the entry rather than the one passed in to the
lookup routine.
First, it sees if the case-exact match already exists in the dcache and
uses it if one exists. Otherwise, it allocates a new node with the new
name and splices it into the dcache.
Original code from ntfs_lookup in fs/ntfs/namei.c by Anton Altaparmakov.
Signed-off-by: Barry Naujok <bnaujok@sgi.com>
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Move rcu-protected lists from list.h into a new header file rculist.h.
This is done because list are a very used primitive structure all over the
kernel and it's currently impossible to include other header files in this
list.h without creating some circular dependencies.
For example, list.h implements rcu-protected list and uses rcu_dereference()
without including rcupdate.h. It actually compiles because users of
rcu_dereference() are macros. Others RCU functions could be used too but
aren't probably because of this.
Therefore this patch creates rculist.h which includes rcupdates without to
many changes/troubles.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Josh Triplett <josh@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the "#ifdef __KERNEL__" tests from unexported header files in
linux/include whose entire contents are wrapped in that preprocessor
test.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new function:
seq_file_root()
This is similar to seq_path(), but calculates the path relative to the
given root, instead of current->fs->root. If the path was unreachable
from root, then modify the root parameter to reflect this.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[mszeredi@suse.cz] split big patch into managable chunks
Add the following functions:
dentry_path()
seq_dentry()
These are similar to d_path() and seq_path(). But instead of
calculating the path within a mount namespace, they calculate the path
from the root of the filesystem to a given dentry, ignoring mounts
completely.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
d_path() is used on a <dentry,vfsmount> pair. Lets use a struct path to
reflect this.
[akpm@linux-foundation.org: fix build in mm/memory.c]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Acked-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New kind of audit rule predicates: "object is visible in given subtree".
The part that can be sanely implemented, that is. Limitations:
* if you have hardlink from outside of tree, you'd better watch
it too (or just watch the object itself, obviously)
* if you mount something under a watched tree, tell audit
that new chunk should be added to watched subtrees
* if you umount something in a watched tree and it's still mounted
elsewhere, you will get matches on events happening there. New command
tells audit to recalculate the trees, trimming such sources of false
positives.
Note that it's _not_ about path - if something mounted in several places
(multiple mount, bindings, different namespaces, etc.), the match does
_not_ depend on which one we are using for access.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
1) Introduces a new method in 'struct dentry_operations'. This method
called d_dname() might be called from d_path() to build a pathname for
special filesystems. It is called without locks.
Future patches (if we succeed in having one common dentry for all
pipes/sockets) may need to change prototype of this method, but we now
use : char *d_dname(struct dentry *dentry, char *buffer, int buflen);
2) Adds a dynamic_dname() helper function that eases d_dname() implementations
3) Defines d_dname method for sockets : No more sprintf() at socket
creation. This is delayed up to the moment someone does an access to
/proc/pid/fd/...
4) Defines d_dname method for pipes : No more sprintf() at pipe
creation. This is delayed up to the moment someone does an access to
/proc/pid/fd/...
A benchmark consisting of 1.000.000 calls to pipe()/close()/close() gives a
*nice* speedup on my Pentium(M) 1.6 Ghz :
3.090 s instead of 3.450 s
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Christoph Hellwig <hch@infradead.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The attached patch destroys all the dentries attached to a superblock in one go
by:
(1) Destroying the tree rooted at s_root.
(2) Destroying every entry in the anon list, one at a time.
(3) Each entry in the anon list has its subtree consumed from the leaves
inwards.
This reduces the amount of work generic_shutdown_super() does, and avoids
iterating through the dentry_unused list.
Note that locking is almost entirely absent in the shrink_dcache_for_umount*()
functions added by this patch. This is because:
(1) at the point the filesystem calls generic_shutdown_super(), it is not
permitted to further touch the superblock's set of dentries, and nor may
it remove aliases from inodes;
(2) the dcache memory shrinker now skips dentries that are being unmounted;
and
(3) the superblock no longer has any external references through which the VFS
can reach it.
Given these points, the only locking we need to do is when we remove dentries
from the unused list and the name hashes, which we do a directory's worth at a
time.
We also don't need to guard against reference counts going to zero unexpectedly
and removing bits of the tree we're working on as nothing else can call dput().
A cut down version of dentry_iput() has been folded into
shrink_dcache_for_umount_subtree() function. Apart from not needing to unlock
things, it also doesn't need to check for inotify watches.
In this version of the patch, the complaint about a dentry still being in use
has been expanded from a single BUG_ON() and now gives much more information.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: NeilBrown <neilb@suse.de>
Acked-by: Ian Kent <raven@themaw.net>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch adds a new directory cache management function that prepares
a disconnected anonymous function to be connected into the dentry tree. The
anonymous dentry is transferred the name and parentage from another dentry.
The following changes were made in [try #2]:
(*) d_materialise_dentry() now switches the parentage of the two nodes around
correctly when one or other of them is self-referential.
The following changes were made in [try #7]:
(*) d_instantiate_unique() has had the interior part split out as function
__d_instantiate_unique(). Callers of this latter function must be holding
the appropriate locks.
(*) _d_rehash() has been added as a wrapper around __d_rehash() to call it
with the most obvious hash list (the one from the name). d_rehash() now
calls _d_rehash().
(*) d_materialise_dentry() is now __d_materialise_dentry() and is static.
(*) d_materialise_unique() added to perform the combination of d_find_alias(),
d_materialise_dentry() and d_add_unique() that the NFS client was doing
twice, all within a single dcache_lock critical section. This reduces the
number of times two different spinlocks were being accessed.
The following further changes were made:
(*) Add the dentries onto their parents d_subdirs lists.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Teach special (recursive) locking code to the lock validator. Has no effect
on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extend the get_sb() filesystem operation to take an extra argument that
permits the VFS to pass in the target vfsmount that defines the mountpoint.
The filesystem is then required to manually set the superblock and root dentry
pointers. For most filesystems, this should be done with simple_set_mnt()
which will set the superblock pointer and then set the root dentry to the
superblock's s_root (as per the old default behaviour).
The get_sb() op now returns an integer as there's now no need to return the
superblock pointer.
This patch permits a superblock to be implicitly shared amongst several mount
points, such as can be done with NFS to avoid potential inode aliasing. In
such a case, simple_set_mnt() would not be called, and instead the mnt_root
and mnt_sb would be set directly.
The patch also makes the following changes:
(*) the get_sb_*() convenience functions in the core kernel now take a vfsmount
pointer argument and return an integer, so most filesystems have to change
very little.
(*) If one of the convenience function is not used, then get_sb() should
normally call simple_set_mnt() to instantiate the vfsmount. This will
always return 0, and so can be tail-called from get_sb().
(*) generic_shutdown_super() now calls shrink_dcache_sb() to clean up the
dcache upon superblock destruction rather than shrink_dcache_anon().
This is required because the superblock may now have multiple trees that
aren't actually bound to s_root, but that still need to be cleaned up. The
currently called functions assume that the whole tree is rooted at s_root,
and that anonymous dentries are not the roots of trees which results in
dentries being left unculled.
However, with the way NFS superblock sharing are currently set to be
implemented, these assumptions are violated: the root of the filesystem is
simply a dummy dentry and inode (the real inode for '/' may well be
inaccessible), and all the vfsmounts are rooted on anonymous[*] dentries
with child trees.
[*] Anonymous until discovered from another tree.
(*) The documentation has been adjusted, including the additional bit of
changing ext2_* into foo_* in the documentation.
[akpm@osdl.org: convert ipath_fs, do other stuff]
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The race is that the shrink_dcache_memory shrinker could get called while a
filesystem is being unmounted, and could try to prune a dentry belonging to
that filesystem.
If it does, then it will call in to iput on the inode while the dentry is
no longer able to be found by the umounting process. If iput takes a
while, generic_shutdown_super could get all the way though
shrink_dcache_parent and shrink_dcache_anon and invalidate_inodes without
ever waiting on this particular inode.
Eventually the superblock gets freed anyway and if the iput tried to touch
it (which some filesystems certainly do), it will lose. The promised
"Self-destruct in 5 seconds" doesn't lead to a nice day.
The race is closed by holding s_umount while calling prune_one_dentry on
someone else's dentry. As a down_read_trylock is used,
shrink_dcache_memory will no longer try to prune the dentry of a filesystem
that is being unmounted, and unmount will not be able to start until any
such active prune_one_dentry completes.
This requires that prune_dcache *knows* which filesystem (if any) it is
doing the prune on behalf of so that it can be careful of other
filesystems. shrink_dcache_memory isn't called it on behalf of any
filesystem, and so is careful of everything.
shrink_dcache_anon is now passed a super_block rather than the s_anon list
out of the superblock, so it can get the s_anon list itself, and can pass
the superblock down to prune_dcache.
If prune_dcache finds a dentry that it cannot free, it leaves it where it
is (at the tail of the list) and exits, on the assumption that some other
thread will be removing that dentry soon. To try to make sure that some
work gets done, a limited number of dnetries which are untouchable are
skipped over while choosing the dentry to work on.
I believe this race was first found by Kirill Korotaev.
Cc: Jan Blunck <jblunck@suse.de>
Acked-by: Kirill Korotaev <dev@openvz.org>
Cc: Olaf Hering <olh@suse.de>
Acked-by: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Balbir Singh <balbir@in.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is very common to hash a dentry and then to call lookup. If we take fs
specific hash functions into account the full hash logic can get ugly.
Further full_name_hash as an inline function is almost 100 bytes on x86 so
having a non-inline choice in some cases can measurably decrease code size.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Previous inotify work avoidance is good when inotify is completely unused,
but it breaks down if even a single watch is in place anywhere in the
system. Robin Holt notices that udev is one such culprit - it slows down a
512-thread application on a 512 CPU system from 6 seconds to 22 minutes.
Solve this by adding a flag in the dentry that tells inotify whether or not
its parent inode has a watch on it. Event queueing to parent will skip
taking locks if this flag is cleared. Setting and clearing of this flag on
all child dentries versus event delivery: this is no in terms of race
cases, and that was shown to be equivalent to always performing the check.
The essential behaviour is that activity occuring _after_ a watch has been
added and _before_ it has been removed, will generate events.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Robert Love <rml@novell.com>
Cc: John McCutchan <ttb@tentacle.dhs.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bunch of asm/bug.h includes are both not needed (since it will get
pulled anyway) and bogus (since they are done too early). Removed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Shrinks "struct dentry" from 128 bytes to 124 on x86, allowing 31 objects
per slab instead of 30.
Cc: John Levon <levon@movementarian.org>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some long time ago, dentry struct was carefully tuned so that on 32 bits
UP, sizeof(struct dentry) was exactly 128, ie a power of 2, and a multiple
of memory cache lines.
Then RCU was added and dentry struct enlarged by two pointers, with nice
results for SMP, but not so good on UP, because breaking the above tuning
(128 + 8 = 136 bytes)
This patch reverts this unwanted side effect, by using an union (d_u),
where d_rcu and d_child are placed so that these two fields can share their
memory needs.
At the time d_free() is called (and d_rcu is really used), d_child is known
to be empty and not touched by the dentry freeing.
Lockless lookups only access d_name, d_parent, d_lock, d_op, d_flags (so
the previous content of d_child is not needed if said dentry was unhashed
but still accessed by a CPU because of RCU constraints)
As dentry cache easily contains millions of entries, a size reduction is
worth the extra complexity of the ugly C union.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Cc: Maneesh Soni <maneesh@in.ibm.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Paul Jackson <pj@sgi.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@epoch.ncsc.mil>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
An unmount of a mount creates a umount event on the parent. If the
parent is a shared mount, it gets propagated to all mounts in the peer
group.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
dentry cache uses sophisticated RCU technology (and prefetching if
available) but touches 2 cache lines per dentry during hlist lookup.
This patch moves d_hash in the same cache line than d_parent and d_name
fields so that :
1) One cache line is needed instead of two.
2) the hlist_for_each_rcu() prefetching has a chance to bring all the
needed data in advance, not only the part that includes d_hash.next.
I also changed one old comment that was wrong for 64bits.
A further optimisation would be to separate dentry in two parts, one that
is mostly read, and one writen (d_count/d_lock) to avoid false sharing on
SMP/NUMA but this would need different field placement depending on 32bits
or 64bits platform.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Linus Torvalds
