Catalin reported that GPIOs used by bcm47xx don't match layout of his
WRT54GS V1.0 board. It seems we need to distinguish these 54G* devices.
Reported-by: Catalin Patulea <cat@vv.carleton.ca>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/7112/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The address prefix 00:90:4C is used by Broadcom in their initial
configuration. When a mac address with the prefix 00:90:4C is used all
devices from the same series are sharing the same mac address. To
prevent mac address collisions we replace them with a mac address based
on the base address. To generate such addresses we take the main mac
address from et0macaddr and increase it by two for the first wifi
device and by 3 for the second one. This matches the printed mac
address on the device. The main mac address increased by one is used as
wan address by the vendor code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: zajec5@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7489/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The reboot on the BCM47XX SoCs is done, by setting the watchdog counter
to 1 and let it trigger a reboot, when it reaches 0. Some devices with
a BCM4705/BCM4785 SoC do not reboot when the counter is set to 1 and
decreased to 0 by the hardware. It looks like it works more reliable
when we set it to 3. As far as I understand the hardware, this should
not make any difference, but I do not have access to any documentation
for this SoC.
It is still not 100% reliable.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: zajec5@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7488/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
Patch was tested on devices with 64 MiB and 256 MiB of RAM.
It documents every part nicely and drops this hacky part of code:
max = off | ((128 << 20) - 1);
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/6808/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some devices may have different features despite sharing the same ID
(e.g. PCI ID). For example 14e4:4331 is usually a dual band, but this
can be "limited". Device with "pci/x/y/devid=0x4332" supports 2.4 GHz
only. Similarly 0x4333 will mean support for 5 GHz only.
Add entry in SPROM so info described above can be extracted and stored.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a few Belkin F7Dxxxx entries, with F7D4401 sourced from online
documentation and the "F7D7302" being observed. F7D3301, F7D3302, and
F7D4302 are reasonable guesses which are unlikely to cause
mis-detection.
Signed-off-by: Cody P Schafer <devel@codyps.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Cc: Cody P Schafer <devel@codyps.com>
Patchwork: https://patchwork.linux-mips.org/patch/6594/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds board detection for the Siemens SE505v2 and the led gpio
configuration. This board does not have any buttons.
This is based on OpenWrt broadcom-diag and Manuel Munz's nvram dump.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6593/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds led and button GPIO configuration for Linksys wrt54g3gv2,
wrt54gsv1 and wrtsl54gs. This is based on OpenWrt broadcom-diag code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6592/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Linksys WRT54G/GS/GL family uses the same boardtype numbers, and
the same gpio configuration. The boardtype numbers are changing with
the hardware versions, but these hardware numbers are different or each
model.
Detect them all as one device, this also worked in OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6591/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The 1074K is a multiprocessing coherent processing system (CPS) based
on modified 74K cores. This patch makes the 1074K an actual unique
CPU type, instead of a 74K derivative, which it is not.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6389/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fixes the following build problen on allmodconfig:
arch/mips/bcm47xx/board.c: In function 'bcm47xx_board_detect':
arch/mips/bcm47xx/board.c:291:14: error: 'ENXIO' undeclared
(first use in this function)
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6571/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"The most notable new addition inside this pull request is the support
for MIPS's latest and greatest core called "inter/proAptiv". The
patch series describes this core as follows.
"The interAptiv is a power-efficient multi-core microprocessor
for use in system-on-chip (SoC) applications. The interAptiv combines
a multi-threading pipeline with a coherence manager to deliver improved
computational throughput and power efficiency. The interAptiv can
contain one to four MIPS32R3 interAptiv cores, system level
coherence manager with L2 cache, optional coherent I/O port,
and optional floating point unit."
The platform specific patches touch all 3 Broadcom families. It adds
support for the new Broadcom/Netlogix XLP9xx Soc, building a common
BCM63XX SMP kernel for all BCM63XX SoCs regardless of core type/count
and full gpio button/led descriptions for BCM47xx.
The rest of the series are cleanups and bug fixes that are MIPS
generic and consist largely of changes that Imgtec/MIPS had published
in their linux-mti-3.10.git stable tree. Random other cleanups and
patches preparing code to be merged in 3.15"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
mips: select ARCH_MIGHT_HAVE_PC_SERIO
mips: delete non-required instances of include <linux/init.h>
MIPS: KVM: remove shadow_tlb code
MIPS: KVM: use common EHINV aware UNIQUE_ENTRYHI
mips/ide: flush dcache also if icache does not snoop dcache
MIPS: BCM47XX: fix position of cpu_wait disabling
MIPS: BCM63XX: select correct MIPS_L1_CACHE_SHIFT value
MIPS: update MIPS_L1_CACHE_SHIFT based on MIPS_L1_CACHE_SHIFT_<N>
MIPS: introduce MIPS_L1_CACHE_SHIFT_<N>
MIPS: ZBOOT: gather string functions into string.c
arch/mips/pci: don't check resource with devm_ioremap_resource
arch/mips/lantiq/xway: don't check resource with devm_ioremap_resource
bcma: gpio: don't cast u32 to unsigned long
ssb: gpio: add own IRQ domain
MIPS: BCM47XX: fix sparse warnings in board.c
MIPS: BCM47XX: add board detection for Linksys WRT54GS V1
MIPS: BCM47XX: fix detection for some boards
MIPS: BCM47XX: Enable buttons support on SSB
MIPS: BCM47XX: Convert WNDR4500 to new syntax
MIPS: BCM47XX: Use "timer" trigger for status LEDs
...
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6320/
The disabling of cpu_wait was done too early, before the detection was
done. This moves the code to a position where it actually works.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6352/
This fixes the following sparse warnings:
arch/mips/bcm47xx/board.c:39:16: warning: Using plain integer as NULL pointer
arch/mips/bcm47xx/board.c:46:16: warning: Using plain integer as NULL pointer
arch/mips/bcm47xx/board.c:53:16: warning: Using plain integer as NULL pointer
arch/mips/bcm47xx/board.c:78:16: warning: Using plain integer as NULL pointer
arch/mips/bcm47xx/board.c:99:16: warning: Using plain integer as NULL pointer
arch/mips/bcm47xx/board.c:109:16: warning: Using plain integer as NULL pointer
arch/mips/bcm47xx/board.c:124:16: warning: Using plain integer as NULL pointer
arch/mips/bcm47xx/board.c:155:16: warning: Using plain integer as NULL pointer
arch/mips/bcm47xx/board.c:177:16: warning: Using plain integer as NULL pointer
arch/mips/bcm47xx/board.c:189:16: warning: Using plain integer as NULL pointer
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6318/
When a nvram reset was performed from CFE, it sometimes does not
contain the productid value in nvram, but it still contains
hardware_version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6316/
This is supported since implementing IRQ domain in ssb.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6315/
Some devices have power LED as well as status LED. The second one is
used to show the firmware is up and running. Set "timer" trigger for
such LEDs.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6312/
This old wgt634u.c was trying to implement a bit ugly support for
Netgear WGT634U. It provided info about LED, flash mapping & layout and
was trying to handle reset button.
This is not needed anymore as we have replacement for all this stuff.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6302/
This includes all devices from OpenWrt's "diag" that we support in arch
code (we have entries for in enum bcm47xx_board).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6301/
So far this adds support for one Netgear model only, but it's designed
and ready to add many more device. We could hopefully import database
from OpenWrt.
Support for SSB is currently disabled, because SSB doesn't implement IRQ
domain yet.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6300/
So far this is mostly just a proof of concept, database consists of a
single device. Creating a nice iterateable array wasn't an option
because devices have different amount of LEDs. And we don't want to
waste memory just because of support for a device with dozens on LEDs.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6299/
The BCM4706 has a problem with the CPU wait instruction. When r4k_wait
or r4k_wait_irqoff is used will just hang and not return from a
msleep(). Removing the cpu_wait functionality is a workaround for this
problem. The BCM4716 does not have this problem.
The BCM4706 SoC uses a MIPS 74K V4.9 CPU.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6288/
This will add the board name to the machine entry in /proc/cpuinfo.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5864/
Fix nvram_read_alpha2 copying too many bytes over the ssb_sprom
structure. Also fix the arguments of the read_macaddr, although the code
was technically not wrong before due to an extra dereference.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6211/
This adds support for vectored interrupt which is supported by the SoC
using a MIPS 74K CPU like the BCM4716 and BCM4706.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6290/
Move the possible nvram sizes from the stack into the data segment
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6044/
plat_irq_dispatch() is called from asm code, add asmlinkage.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6043/
The BCM47xx SoCs have a 8250 serial compatible console at address
0x18000300 and an other at 0x18000400. On most devices 0x18000300 is
wired to some pins on the board, we should use that.
This is the smae for the AI (bcma) and the SB (ssb) bus, this is some
offset on the chip common core.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5889/
bcm47xx only uses the CFE code for early print to a console, but that
is also possible with a early print serial 8250 driver.
The CFE api init causes hangs somewhere in prom_init_cfe() on some
devices like the Buffalo WHR-HP-G54 and the Asus WL-520GU.
This was reported in https://dev.openwrt.org/ticket/4061 and
https://forum.openwrt.org/viewtopic.php?id=17063
This will remove all the CFE handling code from bcm47xx.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5888/
Recently the output of "system type" in /proc/cpuinfo was changed to
Broadcom BCM4730 (Some sample board), but it is better to just print
the SoC name in the "system type" entry. The board name will be added
in the machine entry later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5865/
Let BCM47XX_SSB select the appropriate BMIPS CPUs enountered on those
systems.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6244/
The ADM6996L switch and some Broadcom switches with two MII interfaces
like the BCM5325F connected to two MACs on the SoC, used on some
routers do not return a valid value when reading the PHY id register
and Linux thinks there is no PHY at all, but that is wrong.
This patch registers a fixed phy in the arch code and then searches it
when there is no other phy in the Ethernet driver code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Asus WL520GC and WL520GU are based on the BCM5354 and clocked at
200MHz, but they do not have a clkfreq nvram variable set to the
correct value. This adds a workaround for these devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5843/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some BCM5354 SoCs are running at 200MHz, but it is not possible to read
the clock from a register like it is done on some other SoC in ssb and
bcma. These devices should have a clkfreq nvram configuration value set
to 200, read it and set the clock to the correct value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5842/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The nvram contains some gpio configuration for boards. It is stored in
a gpio<number>=name format e.g.
gpio8=wps_button
gpio4=robo_reset
This patches adds a function to parse these entries, so other driver
can use it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5841/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Do not print the constant system type "Broadcom BCM47XX" but print the
name of the actual SoC in use and the detected board.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5839/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Detect on which board this code is running based on some nvram
settings. This is needed to start board specific workarounds and
configure the leds and buttons which are on different gpios on every board.
This patches add some boards we have seen, but there are many more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5840
Patchwork: https://patchwork.linux-mips.org/patch/5855/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If neither BCM47XX_SSD nor BCM47XX_BCMA is selected, then no
CPU type is available leading to build problems. We fix
this problem by using MIPS32r1 as the default CPU type for
the BCM47XX platform.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5618/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Conflicts:
include/linux/ssb/ssb_driver_gige.h
Also resolves a logical merge conflict in drivers/net/ethernet/broadcom/-
bgmac.c due to change of an API.
An SoC normally do not define path variables for board_rev and
board_type and the Broadcom SDK also uses the nvram values without a
prefix in such cases. Do the same to fill these sprom attributes from
nvram and do not leave them empty, because brcmsmac do not like this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4679/
Signed-off-by: John Crispin <blogic@openwrt.org>
Some nvram values on some devices have a newline character at the end
of the value, that caused read errors. Trim the string before reading
the number.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4745/
Signed-off-by: John Crispin <blogic@openwrt.org>
The nvram functions are exported and used by some normal drivers. To
prevent name clashes with ofter parts of the kernel code add a bcm47xx_
prefix in front of the function names and the header file name.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4744/
Signed-off-by: John Crispin <blogic@openwrt.org>
The old code just worked for nvram with a size of 0x8000 bytes. This
patch adds support for reading nvram from partitions of 0xF000 and
0x10000 bytes.
There is just 32KB space for the nvram, but most devices do not use the
full size and this code reads the first 32KB in that case and prints a
warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4743/
Signed-off-by: John Crispin <blogic@openwrt.org>
This makes it possible to handle the case of not being able to read the
nvram ram. This could happen when the code searching for the specific
flash chip have not run jet.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4740/
Signed-off-by: John Crispin <blogic@openwrt.org>
Instead of using our own error codes use some common codes.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4739/
Signed-off-by: John Crispin <blogic@openwrt.org>
Also check if parallel flash is present at all before accessing it and
add support for serial flash on BCMA bus.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4738/
Signed-off-by: John Crispin <blogic@openwrt.org>
Synchronize with 'net' in order to sort out some l2tp, wireless, and
ipv6 GRE fixes that will be built on top of in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Kconfig items BCM47XX_BCMA and BCM47XX_SSB selected respectively
BCMA_DRIVER_GPIO and SSB_DRIVER_GPIO. These options depend on GPIOLIB
without explicitly selecting it so it results in a warning when GPIOLIB
is not set:
scripts/kconfig/conf --oldconfig Kconfig
warning: (BCM47XX_BCMA) selects BCMA_DRIVER_GPIO ... unmet direct
dependencies (BCMA_POSSIBLE && BCMA && GPIOLIB)
warning: (BCM47XX_SSB) selects SSB_DRIVER_GPIO ... unmet direct
dependencies (SSB_POSSIBLE && SSB && GPIOLIB)
which subsequently results in compile errors.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4759/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The irq signal numbers that are send by the cpu are increased by 2 from
the number programmed into the mips core by bcma.
Return the irq number on which the irqs are send in bcma_core_irq() now.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull MIPS updates from Ralf Baechle:
"The MIPS bits for 3.8. This also includes a bunch fixes that were
sitting in the linux-mips.org git tree for a long time. This pull
request contains updates to several OCTEON drivers and the board
support code for BCM47XX, BCM63XX, XLP, XLR, XLS, lantiq, Loongson1B,
updates to the SSB bus support, MIPS kexec code and adds support for
kdump.
When pulling this, there are two expected merge conflicts in
include/linux/bcma/bcma_driver_chipcommon.h which are trivial to
resolve, just remove the conflict markers and keep both alternatives."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (90 commits)
MIPS: PMC-Sierra Yosemite: Remove support.
VIDEO: Newport Fix console crashes
MIPS: wrppmc: Fix build of PCI code.
MIPS: IP22/IP28: Fix build of EISA code.
MIPS: RB532: Fix build of prom code.
MIPS: PowerTV: Fix build.
MIPS: IP27: Correct fucked grammar in ops-bridge.c
MIPS: Highmem: Fix build error if CONFIG_DEBUG_HIGHMEM is disabled
MIPS: Fix potencial corruption
MIPS: Fix for warning from FPU emulation code
MIPS: Handle COP3 Unusable exception as COP1X for FP emulation
MIPS: Fix poweroff failure when HOTPLUG_CPU configured.
MIPS: MT: Fix build with CONFIG_UIDGID_STRICT_TYPE_CHECKS=y
MIPS: Remove unused smvp.h
MIPS/EDAC: Improve OCTEON EDAC support.
MIPS: OCTEON: Add definitions for OCTEON memory contoller registers.
MIPS: OCTEON: Add OCTEON family definitions to octeon-model.h
ata: pata_octeon_cf: Use correct byte order for DMA in when built little-endian.
MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.
MIPS: Remove usage of CEVT_R4K_LIB config option.
...
Instated of providing an own GPIO driver use the one provided by ssb and
bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4592
Acked-by: Florian Fainelli <florian@openwrt.org>
There are bcma based devices like the Linksys E2000 out there, which do
have one ieee80211 core, but no PCIe core and they are using no
prefixes for the sprom. In addition some values like boardtype are
stored without a prefix for the main SoC chip also when they have an
additional PCIe wifi chip with an own boardtype var on some devices.
The Ethernet addresses are now also read out correctly without a prefix
so calling bcm47xx_fill_sprom_ethernet is not needed any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4364
Signed-off-by: John Crispin <blogic@openwrt.org>
If there is no ieee80211 core on the devices like on the BCM4706 read
out the sprom and the other data without using a prefix.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4361
Signed-off-by: John Crispin <blogic@openwrt.org>
Read out the full board data independently of the sprom version. Now we
also get the full boardflags and so on if sromrev is not set and our
code would assume a rev 1 device. When a nvram option is not set
because it is not there this is no problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4363
Signed-off-by: John Crispin <blogic@openwrt.org>
The memory size is detected by finding a place where it repeats in
memory. Currently we are just checking when the function prom_init is
seen again, but it is better to check for a bigger part of the memory
to decrease the chance of wrong results.
This should fix a problem we saw in OpenWrt, where the detected
available memory decreed on some devices when doing a soft reboot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4362
Signed-off-by: John Crispin <blogic@openwrt.org>
Ignoring the last page when ddr size is 128M. Cached accesses to last
page is causing the processor to prefetch using address above 128M
stepping out of the ddr address space.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4365
Signed-off-by: John Crispin <blogic@openwrt.org>
This is a preparing step for adding serial flash support.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The first thing bcm47xx_fill_sprom does is initialize (zero fill) the SPROM. For
BCMA SOC, this wipes out any values previously read by bcm47xx_fill_sprom_ethernet
(see arch/mips/bcm47xx/setup.c - bcm47xx_get_sprom_bcma). Move the initialization
of SPROM so it is called prior to filling in any values.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the boardrev with a prefix is not available, try to read it
without a prefix. This is based on code from the Broadcom SDK.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This struct contains information about the board, the chip is running
on. The struct is filled for PCIe devices and SoCs. This information is
used by b43 and will be used by brcmsmac soon.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now the fetching of board data also uses nvram_read_u16 and not
simple_strtoul any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the rev contained the revision read from the pci config
space and was used as board_rev in the wireless drivers. This is wrong
the board_rev is only fetched from the sprom accordingly to the open
source part of the Broadcom SDK and brcmsmac. This patch removes the
rev from the boardinfo structure and uses the board_rev attribute from
sprom instead. This attribute is filled by PCI, PCMCIA, SDIO and SoC
code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On SoCs the sprom is often stored in nvram in the flashchip. This patch
registers a sprom fallback callback handler in bcma and provides the
sprom needed for this device.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the sprom parsing from nvram into sprom.c. There are all values
needed for sprom version 1 to 9 read from nvram and there are more
sanity checks added. This is based on the sprom parsing in the open
source part of the Broadcom SDK.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Panic() invokes printk() to add a \n internally, so panic arguments should
not themselves end in \n. Panic invocations in arch/mips and elsewhere
are inconsistently sometimes terminating in \n, sometimes not.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Or else we get lots of variations on this:
arch/mips/pci/pci.c:330: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
scattered throughout the build.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This patch add support for the bcma bus. Broadcom uses only Mips 74K
CPUs on the new SoC and on the old ons using ssb bus there are no Mips
74K CPUs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare bcm47xx to support different System buses. Before adding
support for bcma it should be possible to build bcm47xx without the
need of ssb. With this patch bcm47xx does not directly contain a
ssb_bus, but a union contain all the supported system buses. As a SoC
just uses one system bus a union is a good choice.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some members of the struct ssb_sprom where not filled with data available
in the NVRAM. Some attribute names in the NVRAM changed from SPROM version
3 to version 4. This patch was done by analyzing the the pci sprom parser
in the ssb code and some open source parts of the braodcom wireless driver
used on embedded devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2365/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We are generating the prefix based on the PCI bus address the device is
on. This is done like Broadcom does it in their code expect that the the
bus number is increased by one. In the SB bus implementation used by
Broadcom the SB bus emulates a PCI bus so the kernel sees one PCI bus
more then in our implementation. We do not handle prefixes like sb/1/
yet as they are only used on the new bus which is not implemented yet.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2364/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When an other SSB based device without an own SPROM is attached, using the
PCI bus to the main SSB based device, the data normally found in the SPROM
will be stored in the NVRAM on modern devices. The keys, to load the data
from the NVRAM, are all using some sort of prefix like pci/1/1/, pci/1/3/
or sb/1/ before the actual key. This patch extends bcm47xx_fill_sprom() to
make it possible to read out these values when some prefix was used.
The keys for the SPROM data used on the main chip does not have a prefix.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some devices like the Netgear WGT634U are using ttyS1 for default console
output. We should switch to that console if it was given in the kernel_args
parameters.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1848/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of writing own function for parsing the mac address we now
use sscanf.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1847/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fill the sprom with all available values from the nvram. Most of these
new values are needed for the b43 or b43legacy driver.
Parts of this patch have been in OpenWRT for a long time and were written
by Michael Buesch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1846/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The config options read out here are not stored in CFE but only in NVRAM on
the devices. Remove reading from CFE and only access the NVRAM. Reading out
CFE does not harm but is useless here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1845/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nvram_getenv should behave like cfe_getenv. cfe_getenv returns 0 on
success and -9 if the value was not found. If the input was wrong -8
will be returned by cfe_getenv. Change nvram_getenv to do the same.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Waldemar Brodkorb <wbx@openadk.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1520/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The previous patch 4a86f2d27733f610e642649aca3e82e86fca9e22 (lmo) rsp.
84a6fcb368 (kernel.org) was wrong.
The BCM47xx architecture maps the ram into a 128MB address space. It
will be spaced there as often as goes into the 128MB. Detection tries to
find the position where the same memory is found. When reading beyond
128MB the processor will throw an exception. If 128MB RAM is installed,
it will not find a memory alias because it tries to read beyond the 128MB
border. Now it just assumes 128MB installed ram if it can not find an
alias.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1508/
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rafał Miłecki