Document in Documentation/md.txt the files that now appear in sysfs, and make
a couple of small refinements to exactly when 'level' and 'raid_disks' are
empty, to make it match the documentation.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add documentation as Documentation/fb/fbcon.txt describing the framebuffer
console and its boot options.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make some changes to the NEED_RESCHED and POLLING_NRFLAG to reduce
confusion, and make their semantics rigid. Improves efficiency of
resched_task and some cpu_idle routines.
* In resched_task:
- TIF_NEED_RESCHED is only cleared with the task's runqueue lock held,
and as we hold it during resched_task, then there is no need for an
atomic test and set there. The only other time this should be set is
when the task's quantum expires, in the timer interrupt - this is
protected against because the rq lock is irq-safe.
- If TIF_NEED_RESCHED is set, then we don't need to do anything. It
won't get unset until the task get's schedule()d off.
- If we are running on the same CPU as the task we resched, then set
TIF_NEED_RESCHED and no further action is required.
- If we are running on another CPU, and TIF_POLLING_NRFLAG is *not* set
after TIF_NEED_RESCHED has been set, then we need to send an IPI.
Using these rules, we are able to remove the test and set operation in
resched_task, and make clear the previously vague semantics of
POLLING_NRFLAG.
* In idle routines:
- Enter cpu_idle with preempt disabled. When the need_resched() condition
becomes true, explicitly call schedule(). This makes things a bit clearer
(IMO), but haven't updated all architectures yet.
- Many do a test and clear of TIF_NEED_RESCHED for some reason. According
to the resched_task rules, this isn't needed (and actually breaks the
assumption that TIF_NEED_RESCHED is only cleared with the runqueue lock
held). So remove that. Generally one less locked memory op when switching
to the idle thread.
- Many idle routines clear TIF_POLLING_NRFLAG, and only set it in the inner
most polling idle loops. The above resched_task semantics allow it to be
set until before the last time need_resched() is checked before going into
a halt requiring interrupt wakeup.
Many idle routines simply never enter such a halt, and so POLLING_NRFLAG
can be always left set, completely eliminating resched IPIs when rescheduling
the idle task.
POLLING_NRFLAG width can be increased, to reduce the chance of resched IPIs.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
States a date for removing V4L1 API
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remote and more info for PCTV Cardbus. Whitespace cleanup.
Signed-off-by: Pavel Mihaylov <bin@bash.info>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fixed broken API link and indentation.
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fix bug 5484: ASUS digimatrix card doesnt work with PAL tuner
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Analog support for Asus P7131 Dual - TDA8275A
Signed-off-by: Hermann Pitton <hermann.pitton@onlinehome.de>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Included support for em2800.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Added analog support for ATI HDTV Wonder
Signed-off-by: Kirk Lapray <kirk.lapray@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Added support for OEM version of FlyTV Platinum mini with a subvendor id
of 0x4e42.
- Added the OEM PCI id's to the docs/CARDLIST.saa7134 for item 39
- Modified the vmux in the SAA7134_BOARD_FLYTVPLATINUM_MINI driver data from
0 (Composite over S-Video) to 3 (Composite).
Signed-off-by: Glen Gray <glen@lincor.com>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updated documentation to include "hybrid" v4l/dvb and ATSC cards.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* nxt200x.c, nxt200x.h
- New frontend module that supports both NXT2002 and NXT2004.
So far, only tested on NXT2004. After testing on NXT2002, we should
deprecate the nxt2002 module, and implement this one instead on the
applicable cards.
* get_dvb_firmware:
- Added support for the NXT2004 firmware. This firmware works with both
the ATI HDTV Wonder and the AVerTVHD MCE a180.
This was originally written by Jean-Francois Thibert
* dvb-pll.c
- Fixed minimum frequency for tuv1236d. It seems that the data sheets
are wrong.
Signed-off-by: Kirk Lapray <kirk.lapray@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Updated documentation for FusionHDTV Lite cards. We must differentiate
the bt8xx based "Lite" cards from the cx2388x based "Gold" cards.
- Provide location of CARDLIST.bttv Documentation, rather than
instructing users to look at bttv.h
- Include card decimal id numbers. These are valid for module arguments,
and might be easier for some people to remember, rather than hex.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updated Documentation
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
->permission and ->lookup have a struct nameidata * argument these days to
pass down lookup intents. Unfortunately some callers of lookup_hash don't
actually pass this one down. For lookup_one_len() we don't have a struct
nameidata to pass down, but as this function is a library function only
used by filesystem code this is an acceptable limitation. All other
callers should pass down the nameidata, so this patch changes the
lookup_hash interface to only take a struct nameidata argument and derives
the other two arguments to __lookup_hash from it. All callers already have
the nameidata argument available so this is not a problem.
At the same time I'd like to deprecate the lookup_hash interface as there
are better exported interfaces for filesystem usage. Before it can
actually be removed I need to fix up rpc_pipefs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The CONFIG_EXT{2,3}_CHECK options where were never available, and all they
did was to implement a subset of e2fsck in the kernel.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch schedules obsolete OSS drivers (with ALSA drivers that support
the same hardware) for removal.
Scheduling the via82cxxx driver for removal was ACK'ed by Jeff Garzik.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Carlo Comin <vl4d spine-group.org>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The big i2c-viapro SMBus driver update which went into 2.6.14-git1
introduced a few minor issues. Nothing critical, but I would like a
few adjustments to be merged in to fix the following problems:
* VIA should not be spelled Via.
* Frodo Looijaard and Philip Edelbrock did not write the i2c-viapro
driver.
* When debugging is disabled, half of messages would be logged.
* Drop an unneeded masking.
* Some port reads can be avoided now that the transaction size is
passed as a parameter to vt596_transaction().
* SMBus Receive Byte transactions are used for probing too (for
EEPROMs), so hide errors on these too.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My latest update to the writing-clients i2c documentation file was
incomplete, here's the complement.
Large parts of this file are still way out-of-date, but at least now
the memory allocation and freeing instructions are consistent.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Would you mind applying the following patch that kills those two + the
m68k and Documentation/ references?
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This looks like something which out-of-tree code could possibly be using.
Give panic_timeout the twelve-month treatment.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This looks like something which out-of-tree code could possibly be using.
Give insert_resource the twelve-month treatment.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Docs for ramfs, rootfs, and initramfs.
Signed-off-by: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch splits dentry locking documentation from
Documentation/filesystems/vfs.txt to a separate file. The dentry locking
bits are useful but do not fit into the VFS overview document as is.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch updates the Documentation/filesystems/vfs.txt document. I
rearranged and rewrote parts of the introduction chapter and added better
headings for each section. I also added a description for the inode
rename() operation which was missing and added links to some useful
external VFS documentation.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Put text into < 80 columns. No other changes.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix various warnings in kernel-doc:
Warning(linux-2614-rc4//include/linux/net.h:89): Enum value 'SOCK_DCCP' not described in enum 'sock_type'
usercopy.c: should use !E instead of !I for exported symbols:
Warning(linux-2614-rc4//arch/i386/lib/usercopy.c): no structured comments found
fs.h does not need to use !E since it has no exported symbols:
Warning(linux-2614-rc4//include/linux/fs.h:1182): No description found for parameter 'find_exported_dentry'
Warning(linux-2614-rc4//include/linux/fs.h): no structured comments found
irq/manage.c should use !E for its exported symbols:
Warning(linux-2614-rc4//kernel/irq/manage.c): no structured comments found
macmodes.c should use !E for its exported symbols:
Warning(linux-2614-rc4//drivers/video/macmodes.c): no structured comments found
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add structure fields kernel-doc for 2 fields in struct journal_s.
Warning(/var/linsrc/linux-2614-rc4//include/linux/jbd.h:808): No description found for parameter 'j_wbuf'
Warning(/var/linsrc/linux-2614-rc4//include/linux/jbd.h:808): No description found for parameter 'j_wbufsize'
Convert fs/jbd/recovery.c non-static functions to kernel-doc format.
fs/jbd/recovery.c doesn't export any symbols, so it should use
!I instead of !E to eliminate this warning message:
Warning(/var/linsrc/linux-2614-rc4//fs/jbd/recovery.c): no structured comments found
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've recently added this documentation, Alasdair gave some corrections, and
here are some further corrections on top of his work (partly style issue,
partly a technical error due to different past experience, partly a note
which I've added - i.e. transient snapshots are lighter).
Cc: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
vesafb occassionally gets the size wrong when setting the mtrr. When X or DRI
attempts to set the mtrr, it will fail due to range overlap significantly
affecting their performance. Disable mtrr and let the user explicitly enable
it with the mtrr:n option.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds a RapidIO subsystem to the kernel. RIO is a switched fabric interconnect
used in higher-end embedded applications. The curious can look at the specs
over at http://www.rapidio.org
The core code implements enumeration/discovery, management of
devices/resources, and interfaces for RIO drivers.
There's a lot more to do to take advantages of all the hardware features.
However, this should provide a good base for folks with RIO hardware to start
contributing.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updates to Documentation/vm/hugetlbpage.txt:
- there's no need to select HUGETLB_PAGE manually and it's no longer
under the processor menu. Update the text accordingly.
- fix typos and trim trailing whitespace.
Signed-Off-By: Muli Ben-Yehuda <mulix@mulix.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the hlist_for_each_rcu() API, which is used only in one place, and
is trivially converted to hlist_for_each_entry_rcu(), making the code
shorter and more readable. Any out-of-tree uses may be similarly
converted.
Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix typos and add a section about cpus in the driver-model documentation.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds few more working systems.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch renames struct kmem_cache_s to kmem_cache so we can start using
it instead of kmem_cache_t typedef.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds SCSI error handling code to the SCSI portion
of the cciss driver.
Signed-off-by: Stephen M. Cameron <steve.cameron@hp.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SCSI qlogicisp driver is both marked BROKEN and superseded by the
qla1280 driver.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
undefined symbol in Documentation/scsi/scsi_eh.txt
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hi,
This patch provides updated documentation on the Neterion(S2io) driver.
Please review the patch.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- egcs is not supported by kernel 2.6
- gcc 3.3 seems to be a good choice on ARM
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Modules: Documentation,ALI5451 driver,NM256 driver
Removed multi-card supports for ali5451 and nm256 drivers.
They are supposed to be a single device.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Documentation,MIPS AU1x00 driver,PPC Beep,SPARC DBRI driver
Removed the use of chip_t, which was obsoleted.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Remove vmalloc wrapper
- Add release_and_free_resource() to remove kfree_nocheck() from each driver
and simplify the code
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Documentation,PCM Midlevel,Timer Midlevel,ALSA Core
Use the standard getnstimeofday() function instead of ALSA's own one.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove snd_runtime_check() macro.
This macro worsens the readability of codes. They should be either
normal if() or removable asserts.
Also, the assert displays stack-dump, instead of only the last caller
pointer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the code for supporting eight cards from the integrated
controller drivers because There Can Be Only One controller of
each type per mainboard.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Fix up etherdevice docbook comments and make them (and other networking stuff)
get dragged into the kernel-api. Delete the old 8390 stuff, it really isn't
interesting anymore.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Patch from Ben Dooks
Update the Documentation/arm/Samsung-S3C24XX to add
example platform data initialisation, and add the
linux-arm mailing list URL.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is a rewrite of the one submitted on October 1st, using modules
(http://marc.theaimsgroup.com/?l=linux-kernel&m=112819093522998&w=2).
This rewrite adds a tristate CONFIG_RCU_TORTURE_TEST, which enables an
intense torture test of the RCU infratructure. This is needed due to the
continued changes to the RCU infrastructure to accommodate dynamic ticks,
CPU hotplug, realtime, and so on. Most of the code is in a separate file
that is compiled only if the CONFIG variable is set. Documentation on how
to run the test and interpret the output is also included.
This code has been tested on i386 and ppc64, and an earlier version of the
code has received extensive testing on a number of architectures as part of
the PREEMPT_RT patchset.
Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch adds LSM hooks for key management facilities. The notable
changes are:
(1) The key struct now supports a security pointer for the use of security
modules. This will permit key labelling and restrictions on which
programs may access a key.
(2) Security modules get a chance to note (or abort) the allocation of a key.
(3) The key permission checking can now be enhanced by the security modules;
the permissions check consults LSM if all other checks bear out.
(4) The key permissions checking functions now return an error code rather
than a boolean value.
(5) An extra permission has been added to govern the modification of
attributes (UID, GID, permissions).
Note that there isn't an LSM hook specifically for each keyctl() operation,
but rather the permissions hook allows control of individual operations based
on the permission request bits.
Key management access control through LSM is enabled by automatically if both
CONFIG_KEYS and CONFIG_SECURITY are enabled.
This should be applied on top of the patch ensubjected:
[PATCH] Keys: Possessor permissions should be additive
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(akpm: I don't do typo patches, but one of these is in a printk string)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed some more references to check_region().
I checked these changes into the 'checkreg' branch of
rsync://rsync.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6.git
The only valid references remaining are in:
drivers/scsi/advansys.c
drivers/scsi/BusLogic.c
drivers/cdrom/sbpcd.c
sound/oss/pss.c
Remove last vestiges of ide_check_region()
drivers/char/specialix: trim trailing whitespace
drivers/char/specialix: eliminate use of check_region()
Remove outdated and unused references to check_region()
[sound oss] remove check_region() usage from cs4232, wavfront
[netdrvr eepro] trim trailing whitespace
[netdrvr eepro] remove check_region() usage
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was one small but very significant change in the previous patch:
mprotect's flush_tlb_range fell outside the page_table_lock: as it is in 2.4,
but that doesn't prove it safe in 2.6.
On some architectures flush_tlb_range comes to the same as flush_tlb_mm, which
has always been called from outside page_table_lock in dup_mmap, and is so
proved safe. Others required a deeper audit: I could find no reliance on
page_table_lock in any; but in ia64 and parisc found some code which looks a
bit as if it might want preemption disabled. That won't do any actual harm,
so pending a decision from the maintainers, disable preemption there.
Remove comments on page_table_lock from flush_tlb_mm, flush_tlb_range and
flush_tlb_page entries in cachetlb.txt: they were rather misleading (what
generic code does is different from what usually happens), the rules are now
changing, and it's not yet clear where we'll end up (will the generic
tlb_flush_mmu happen always under lock? never under lock? or sometimes under
and sometimes not?).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Please, please now delete the Atari CONFIG_STRAM_SWAP code. It may be
excellent and ingenious code, but its reference to swap_vfsmnt betrays that it
hasn't been built since 2.5.1 (four years old come December), it's delving
deep into matters which are the preserve of core mm code, its only purpose is
to give the more conscientious mm guys an anxiety attack from time to time;
yet we keep on breaking it more and more.
If you want to use RAM for swap, then if the MTD driver does not already
provide just what you need, I'm sure David could be persuaded to add the
extra. But you'd also like to be able to allocate extents of that swap for
other use: we can give you a core interface for that if you need. But unbuilt
for four years suggests to me that there's no need at all.
I cannot swear the patch below won't break your build, but believe so.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- converted to platform bus
- removed pci dependencies
- removed virt_to_phys/phys_to_virt calls
System now can root off of a disk.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
diff --git a/Documentation/mips/AU1xxx_IDE.README b/Documentation/mips/AU1xxx_IDE.README
new file mode 100644
The default value for tcp_tso_win_divisor is 3.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This revised patch (as586b) makes usb-handoff permanently true and no
longer a kernel boot parameter. It also removes the piix3_usb quirk code;
that was nothing more than an early version of the USB handoff code
(written at a time when Intel's PIIX3 was about the only motherboard with
USB support). And it adds identifiers for the three PCI USB controller
classes to pci_ids.h.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb/core/buffer.c doesn't export any symbols, so it should use
!I instead of !E to eliminate this warning message:
Warning(/var/linsrc/linux-2614-rc4//drivers/usb/core/buffer.c): no structured comments found
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just a small patch that fixes a small parameter validation bug.
drivers/usb/input/map_to_7segment.h:
This patch fixes the broken parameter validation in the char to seg7
conversion. This could cause out-of-bounds memory references.
MAINTAINERS:
Yealink maintainer info now in sorted order.
Documentation/input/yealink.txt:
Added a Q&A section that answers some common questions.
Signed-off-by: Henk <Henk.Vergonet@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
006491df1a13f85ad245d1039dfdf20e49c394fd
PCI hotplug.c: does not contain kernel-doc, so don't process it for now.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The SMSC LPC47M997 Super-I/O chip seems to be compatible with the
LPC47M192, so it is supported by the smsc47m1 driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the I2C addresses for the ADM1032 and ADT7461 chips.
Also update the links to the Analog Devices web site.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add PEC support to the lm90 driver. Only the ADM1032 chip supports it,
and in a rather tricky way, which is why this patch comes with
documentation reinforcements. At least, this demonstrates that the new
PEC support logic in i2c-core can properly deal with chips with partial
PEC support.
As enabling PEC causes a significant performance drop, it can be
disabled through a sysfs file (unsurprisingly named "pec").
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the documented list of devices supported by the i2c-i810
driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the i2c documentation: kzalloc should be used instead of
kmalloc.
I also fixed a couple other things nearby in writing-clients, as several
past changes had never been reported there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New driver for the Xicor X1205 RTC chip.
Signed-off-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new ID to the SMSC LPC47B397-NC hardware
monitoring driver - for a chip that is claimed to be 100%
compatible otherwise.
Signed-off-by: Bryan Young (Utilitek Systems, Inc.)
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop legacy ISA address support from the it87 driver. All supported
chips are Super-I/O chips, so the device ISA address can be safely read
from Super-I/O space rather than blindly assumed.
Two nearby inaccurate documentation statements have been fixed as well:
* The IT8705F doesn't have an SMBus interface.
* The SiS950 doesn't have a distinct prefix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c documentation fixes.
>From Hideki Iwamoto:
* i2c_smbus_read_i2c_block_data is not deleted in 2.6.10. It still
exists.
* The name which can be set to i2c_driver is up to 31 characters.
>From Jean Delvare:
* Reword the paragraph about i2c_driver.name, to reflect the "new"
naming policy.
* Delete the out-of-date note about now gone inc_use and dec_use
fields.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make it clearer which chips are supported by the i2c-viapro driver,
and which support I2C block transactions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/i2c/busses/i2c-viapro | 12 ++++++------
drivers/i2c/busses/i2c-viapro.c | 22 +++++++++++++---------
2 files changed, 19 insertions(+), 15 deletions(-)
Implement the I2C block transactions on VIA chips which support them:
VT82C686B, VT8233, VT8233A, VT8235 and VT8237R. This speeds up EEPROM
accesses by a factor 10 or so.
I would like to thank Antonino A. Daplas, Hinko Kocevar, Salah Coronya
and Andreas Henriksson for their help in testing this new feature.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/i2c/busses/i2c-viapro | 7 +++++-
drivers/i2c/busses/i2c-viapro.c | 39 +++++++++++++++++++++++++++++++++---
2 files changed, 42 insertions(+), 4 deletions(-)
Before I go on cleaning up and improving the i2c-viapro driver, let's
fix all the coding style issues: mostly trailing white space, and
spaces used where tabs should be.
Signed-off-by: Jean Delvare <khali@linux-fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/i2c/busses/i2c-viapro | 12 ++---
drivers/i2c/busses/i2c-viapro.c | 76 ++++++++++++++++++------------------
2 files changed, 43 insertions(+), 45 deletions(-)
Do not enable the VIA VT82C686A/B integrated sensors by default, as
disabled sensors usually means that this feature is not used so the
values won't make any sense. This has been confusing many users in the
past:
http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=1786http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=1811http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=2052
It is still possible to forcibly enable the sensors by using the
force_addr module parameter.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/hwmon/via686a | 17 +++++++++++++++--
drivers/hwmon/via686a.c | 18 +++++++++++-------
2 files changed, 26 insertions(+), 9 deletions(-)
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the Documentation/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in example code in Documentation/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 071 release is needed to handle the input changes. Older versions
will work properly with module-based systems, but not for users that
build input stuff into the kernel.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The document porting.txt in Documentation/driver-model says:
When a device is successfully bound to a device
I think it should say:
When a device is successfully bound to a driver
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix typos & trailing whitespace.
Add blank lines in a few places.
Remove "AM53C974=" option: driver does not exist.
Restrict to < 80 columns in most places (but don't split formatted
command-line arguments).
Add a few option arguments for completeness.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix some simple typos in the bonding.txt file. The typos are in areas
relating to loading the bonding driver multiple times.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Updated documentation to reflect 2.6.14 netlink changes
about socket options, multicasting and group number.
Please concider for 2.6.14.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current dell_rbu code ver 2.0 the packet update mechanism makes the
user app dump every individual packet in to the driver.
This adds in efficiency as every packet update makes the
/sys/class/firmware/dell_rbu/loading and data files to disappear and reappear
again. Thus the user app needs to wait for the files to reappear to dump
another packet. This slows down the packet update tremendously in case of
large number of packets. I am submitting a new patch for dell_rbu which will
change the way we do packet updates;
In the new method the user app will create a new single file which has already
packetized the rbu image and all the packets are now staged in this file.
This driver also creates a new entry in
/sys/devices/platform/dell_rbu/packet_size ; the user needs to echo the packet
size here before downloading the packet file.
The user should do the following:
create one single file which has all the packets stacked together.
echo the packet size in to /sys/devices/platform/dell_rbu/packet_size.
echo 1 > /sys/class/firmware/dell_rbu/loading
cat the packetfile > /sys/class/firmware/dell_rbu/data
echo 0 > /sys/class/firmware/dell_rbu/loading
The driver takes the file which came through /sys/class/firmware/dell_rbu/data
and takes chunks of paket_size data from it and place in contiguous memory.
This makes packet update process very efficient and fast. As all the packet
update happens in one single operation. The user can still read back the
downloaded file from /sys/devices/platform/dell_rbu/data.
Signed-off-by: Abhay Salunke <abhay_salunke@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
file operations ->write(), ->aio_write(), and ->writev() for regular
files. This replaces the old use of generic_file_write(), et al and
the address space operations ->prepare_write and ->commit_write.
This means that both sparse and non-sparse (unencrypted and
uncompressed) files can now be extended using the normal write(2)
code path. There are two limitations at present and these are that
we never create sparse files and that we only have limited support
for highly fragmented files, i.e. ones whose data attribute is split
across multiple extents. When such a case is encountered,
EOPNOTSUPP is returned.
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
The attached patch adds documentation for the process by which request-key
works, including how it permits helper processes to gain access to the
requestor's keyrings.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hello, Jeff.
This patch adds ATA errors & exceptions chapter to
Documentation/DocBook/libata.tmpl. As suggested, the chapter is
placed before low level driver specific chapters. Contents are
unchanged from the last posting.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Improve explanation of the Subject line fields in
Documentation/SubmittingPatches Canonical Patch Format.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Document more details of patch format such as the "from" line
and the "---" marker line, and provide more references for
patch guidelines.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch adds extra permission grants to keys for the possessor of a
key in addition to the owner, group and other permissions bits. This makes
SUID binaries easier to support without going as far as labelling keys and key
targets using the LSM facilities.
This patch adds a second "pointer type" to key structures (struct key_ref *)
that can have the bottom bit of the address set to indicate the possession of
a key. This is propagated through searches from the keyring to the discovered
key. It has been made a separate type so that the compiler can spot attempts
to dereference a potentially incorrect pointer.
The "possession" attribute can't be attached to a key structure directly as
it's not an intrinsic property of a key.
Pointers to keys have been replaced with struct key_ref *'s wherever
possession information needs to be passed through.
This does assume that the bottom bit of the pointer will always be zero on
return from kmem_cache_alloc().
The key reference type has been made into a typedef so that at least it can be
located in the sources, even though it's basically a pointer to an undefined
type. I've also renamed the accessor functions to be more useful, and all
reference variables should now end in "_ref".
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add information about required version of the userspace library/utilities
to Documentation/Changes. Also add pointer to this and to FUSE
documentation from Kconfig.
Thanks to Anton Altaparmakov for the reminder.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've recently discovered the real functionality of device-mapper snapshots,
and since they are not well known, I've decided to write some docs for
them.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch (as564) updates Documentation/usb/URB.txt, bringing it roughly
up to the current level.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__FUNCTION__ is the prefered kernel idiom, __func__ is not supported by gcc
2.95 (we actually map __FUNCTION__ to __func__ for more recent compilers,
but it should never be used directly)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a new chapter on memory allocation to
Documentation/CodingStyle.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
BUG fixes:
The driver used to allocate memory with spinlock held which has been
fixed in this patch.
The driver was printing the entire buffer when it received a invalid
entry in image_type. The fix is to only print a warning message and not
the buffer.
Usability enhancements:
It is possible that due to user error the /sys/class/firmware/dell_rbu
entries might be missing, this can happen if the user does the following
echo 1 > /sys/class/firmware/dell_rbu/loading
echo 0 > /sys/class/firmware/dell_rbu/loading
This will make the entries in /sys/class/firmware/ to disappear and the
only way get them back was bby unloading and loading the driver.
This patch makes the user recreate these entries by echoing init in to
image_type.
This patch has been tested with Libsmbios and Dell OpenManage.
Signed-off-by: Abhay Salunke <Abhay_Salunke@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add Documentation/ia64/mca.txt, an ad-hoc collection of notes on IA64
MCA and INIT processing.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
As written in Documentation/feature-removal-schedule.txt, remove the
io_remap_page_range() kernel API.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added clarification on the root device format to be used for second kernel,
as well as specifying initrd if drivers are built as modules.
Signed-off-by: Kishore Sampathkumar <kishore.sampathkumar@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds new PCI and subsystem ID's that finally made the spec. It
also include a name change for one controller. I know there's a lot of
duplicat names but the fw folks wanted this for the different implementations.
Even though the same ASIC is used it may be embedded on some platforms,
standup card in others, and a mezzanine in other servers.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We seem to use both asm-offsets.* and asm_offsets.*
Signed-off-by: Michal K. K. Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update Documentation/usb/proc_usb_info.txt:
- remove some trailing whitespace
- add a blank line before each T: line to match current kernel
and to make the text more readable.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a driver for the USB touchpad which can be found on post-February 2005
Apple PowerBooks.
This driver is derived from Johannes Berg's appletrackpad driver [1],
but it has been improved in some areas:
* appletouch is a full kernel driver, no userspace program is necessary
* appletouch can be interfaced with the synaptics X11 driver[2], in order
to have touchpad acceleration, scrolling, two/three finger tap, etc.
This driver has been tested by the readers of the 'debian-powerpc' mailing
list for a few weeks now and I believe it is now ready for inclusion into the
mainline kernel.
Credits go to Johannes Berg for reverse-engineering the touchpad protocol,
Frank Arnold for further improvements, and Alex Harper for some additional
information about the inner workings of the touchpad sensors.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Original patch from Bertro Simul
This is probably still not quite correct, but seems to be
the best solution so far.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Documentation,Intel8x0 driver
Added buggy_semaphore module option to snd-intel8x0 driver
for a workaround for hardwards with buggy codec semaphores.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update i810fb documentation to describe new features and configuration
changes.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kernel connector - new userspace <-> kernel space easy to use
communication module which implements easy to use bidirectional
message bus using netlink as it's backend. Connector was created to
eliminate complex skb handling both in send and receive message bus
direction.
Connector driver adds possibility to connect various agents using as
one of it's backends netlink based network. One must register
callback and identifier. When driver receives special netlink message
with appropriate identifier, appropriate callback will be called.
From the userspace point of view it's quite straightforward:
socket();
bind();
send();
recv();
But if kernelspace want to use full power of such connections, driver
writer must create special sockets, must know about struct sk_buff
handling... Connector allows any kernelspace agents to use netlink
based networking for inter-process communication in a significantly
easier way:
int cn_add_callback(struct cb_id *id, char *name, void (*callback) (void *));
void cn_netlink_send(struct cn_msg *msg, u32 __groups, int gfp_mask);
struct cb_id
{
__u32 idx;
__u32 val;
};
idx and val are unique identifiers which must be registered in
connector.h for in-kernel usage. void (*callback) (void *) - is a
callback function which will be called when message with above idx.val
will be received by connector core.
Using connector completely hides low-level transport layer from it's
users.
Connector uses new netlink ability to have many groups in one socket.
[ Incorporating many cleanups and fixes by myself and
Andrew Morton -DaveM ]
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When introducing the generic asm-offsets.h support the dependency
chain for the prepare targets was changed. All build scripts expecting
include/asm/asm-offsets.h to be made when using the prepare target would broke.
With the limited number of prepare targets left in arch Makefiles
the trivial solution was to introduce a new arch specific target: archprepare
The dependency chain looks like this now:
prepare
|
+--> prepare0
|
+--> archprepare
|
+--> scripts_basic
+--> prepare1
|
+---> prepare2
|
+--> prepare3
So prepare 3 is processed before prepare2 etc.
This guaantees that the asm symlink, version.h, scripts_basic
are all updated before archprepare is processed.
prepare0 which build the asm-offsets.h file will need the
actions performed by archprepare.
The head target is now named prepare, because users scripts will most
likely use that target, but prepare-all has been kept for compatibility.
Updated Documentation/kbuild/makefiles.txt.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
James Bottomley