Processing multicast / broadcast in fast path is performance draining
and having more links means more cloning and bringing performance
down further.
Broadcast; in particular, need to be given to all the virtual links.
Earlier tricks of enabling broadcast bit for IPv4 only interfaces are not
really working since it fails autoconf. Which means enabling broadcast
for all the links if protocol specific hacks do not have to be added into
the driver.
This patch defers all (incoming as well as outgoing) multicast traffic to
a work-queue leaving only the unicast traffic in the fast-path. Now if we
need to apply any additional tricks to further reduce the impact of this
(multicast / broadcast) type of traffic, it can be implemented while
processing this work without affecting the fast-path.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an ipvlan interface is down, its addresses are not on the hash list.
Fix checks for existence of addresses not to depend on the hash list, walk
through all interface addresses instead.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch to add __percpu qualifier to pcpu_stats
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the port check [ipvlan_dev_master()] and device check
[ipvlan_dev_slave()] functions to netdevice.h and rename them
netif_is_ipvlan_port() and netif_is_ipvlan() resp. to be
consistent with macvlan api naming.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver uses ip_out_local() and ip6_route_output() which are
defined only if CONFIG_INET and CONFIG_IPV6 are enabled respectively.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is very similar to the macvlan driver except that it
uses L3 on the frame to determine the logical interface while
functioning as packet dispatcher. It inherits L2 of the master
device hence the packets on wire will have the same L2 for all
the packets originating from all virtual devices off of the same
master device.
This driver was developed keeping the namespace use-case in
mind. Hence most of the examples given here take that as the
base setup where main-device belongs to the default-ns and
virtual devices are assigned to the additional namespaces.
The device operates in two different modes and the difference
in these two modes in primarily in the TX side.
(a) L2 mode : In this mode, the device behaves as a L2 device.
TX processing upto L2 happens on the stack of the virtual device
associated with (namespace). Packets are switched after that
into the main device (default-ns) and queued for xmit.
RX processing is simple and all multicast, broadcast (if
applicable), and unicast belonging to the address(es) are
delivered to the virtual devices.
(b) L3 mode : In this mode, the device behaves like a L3 device.
TX processing upto L3 happens on the stack of the virtual device
associated with (namespace). Packets are switched to the
main-device (default-ns) for the L2 processing. Hence the routing
table of the default-ns will be used in this mode.
RX processins is somewhat similar to the L2 mode except that in
this mode only Unicast packets are delivered to the virtual device
while main-dev will handle all other packets.
The devices can be added using the "ip" command from the iproute2
package -
ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ]
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Laurent Chavey <chavey@google.com>
Cc: Tim Hockin <thockin@google.com>
Cc: Brandon Philips <brandon.philips@coreos.com>
Cc: Pavel Emelianov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar