Our goal is to touch skb_shinfo(skb) only when absolutely needed,
to avoid two cache line misses in TCP output path for last skb
that is considered but not sent because of various conditions
(cwnd, tso defer, receiver window, TSQ...)
A packet is GSO only when skb_shinfo(skb)->gso_size is not zero.
We can set skb_shinfo(skb)->gso_type to sk->sk_gso_type even for
non GSO packets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_gso_segment() and tcp_gro_receive() are not strictly
part of TCP stack. They should not assume tcp_skb_mss(skb)
is in fact skb_shinfo(skb)->gso_size.
This will allow us to change tcp_skb_mss() in following patches.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a BUG_ON() where CONFIG_NET_SWITCHDEV is set but the driver for a
bridged port does not support switchdev_port_attr_set op. Don't BUG_ON()
if -EOPNOTSUPP is returned.
Also change BUG_ON() to netdev_err since this is a normal error path and
does not warrant the use of BUG_ON(), which is reserved for unrecoverable
errs.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reported-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support of Marvell NFC chip controlled over UART
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some NFC controller supports UART as host interface.
As with SPI, a lot of code can be shared between vendor
drivers. This patch add the generic support of UART and
provides some extension API for vendor specific needs.
This code is strongly inspired by the Bluetooth HCI ldisc
implementation. NCI UART vendor drivers will have to register
themselves to this layer via nci_uart_register.
Underlying tty will have to be configured from user land
thanks to an ioctl.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add strings array of the current supported tunable options.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CAIA Delay-Gradient (CDG) is a TCP congestion control that modifies
the TCP sender in order to [1]:
o Use the delay gradient as a congestion signal.
o Back off with an average probability that is independent of the RTT.
o Coexist with flows that use loss-based congestion control, i.e.,
flows that are unresponsive to the delay signal.
o Tolerate packet loss unrelated to congestion. (Disabled by default.)
Its FreeBSD implementation was presented for the ICCRG in July 2012;
slides are available at http://www.ietf.org/proceedings/84/iccrg.html
Running the experiment scenarios in [1] suggests that our implementation
achieves more goodput compared with FreeBSD 10.0 senders, although it also
causes more queueing delay for a given backoff factor.
The loss tolerance heuristic is disabled by default due to safety concerns
for its use in the Internet [2, p. 45-46].
We use a variant of the Hybrid Slow start algorithm in tcp_cubic to reduce
the probability of slow start overshoot.
[1] D.A. Hayes and G. Armitage. "Revisiting TCP congestion control using
delay gradients." In Networking 2011, pages 328-341. Springer, 2011.
[2] K.K. Jonassen. "Implementing CAIA Delay-Gradient in Linux."
MSc thesis. Department of Informatics, University of Oslo, 2015.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: David Hayes <davihay@ifi.uio.no>
Cc: Andreas Petlund <apetlund@simula.no>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Nicolas Kuhn <nicolas.kuhn@telecom-bretagne.eu>
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upcoming tcp_cdg uses tcp_enter_cwr() to initiate PRR. Export this
function so that CDG can be compiled as a module.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: David Hayes <davihay@ifi.uio.no>
Cc: Andreas Petlund <apetlund@simula.no>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Nicolas Kuhn <nicolas.kuhn@telecom-bretagne.eu>
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_NET_SWITCHDEV is enabled, but port driver does not implement
support for IPv4 FIB add/del ops, don't fail route add/del offload
operations. Route adds will not be marked as OFFLOAD. Routes will be
installed in the kernel FIB, as usual.
This was report/fixed by Florian when testing DSA driver with net-next on
devices with L2 offload support but no L3 offload support. What he reported
was an initial route installed from DHCP client would fail (route not
installed to kernel FIB). This was triggering the setting of
ipv4.fib_offload_disabled, which would disable route offloading after the
first failure. So subsequent attempts to install the route would succeed.
There is follow-on work/discussion to address the handling of route install
failures, but for now, let's differentiate between no support and failed
support.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dctcp_alpha can be read by from dctcp_get_info() without
synchro, so use WRITE_ONCE() to prevent compiler from using
dctcp_alpha as a temporary variable.
Also, playing with small dctcp_shift_g (like 1), can expose
an overflow with 32bit values shifted 9 times before divide.
Use an u64 field to avoid this problem, and perform the divide
only if acked_bytes_ecn is not zero.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* mesh fixes from Alexis Green and Chun-Yeow Yeoh,
* a documentation fix from Jakub Kicinski,
* a missing channel release (from Michal Kazior),
* a fix for a signal strength reporting bug (from Sara Sharon),
* handle deauth while associating (myself),
* don't report mangled TX SKB back to userspace for status (myself),
* handle aggregation session timeouts properly in fast-xmit (myself)
However, there are also a few cleanups and one big change that
affects all drivers (and that required me to pull in your tree)
to change the mac80211 HW flags to use an unsigned long bitmap
so that we can extend them more easily - we're running out of
flags even with a cleanup to remove the two unused ones.
-----BEGIN PGP SIGNATURE-----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=2wTw
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-06-10' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For this round we mostly have fixes:
* mesh fixes from Alexis Green and Chun-Yeow Yeoh,
* a documentation fix from Jakub Kicinski,
* a missing channel release (from Michal Kazior),
* a fix for a signal strength reporting bug (from Sara Sharon),
* handle deauth while associating (myself),
* don't report mangled TX SKB back to userspace for status (myself),
* handle aggregation session timeouts properly in fast-xmit (myself)
However, there are also a few cleanups and one big change that
affects all drivers (and that required me to pull in your tree)
to change the mac80211 HW flags to use an unsigned long bitmap
so that we can extend them more easily - we're running out of
flags even with a cleanup to remove the two unused ones.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SCM_SECURITY was originally only implemented for datagram sockets,
not for stream sockets. However, SCM_CREDENTIALS is supported on
Unix stream sockets. For consistency, implement Unix stream support
for SCM_SECURITY as well. Also clean up the existing code and get
rid of the superfluous UNIXSID macro.
Motivated by https://bugzilla.redhat.com/show_bug.cgi?id=1224211,
where systemd was using SCM_CREDENTIALS and assumed wrongly that
SCM_SECURITY was also supported on Unix stream sockets.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the addition of sysfs multicast router support if one set
multicast_router to "2" more than once, then the port would be added to
the hlist every time and could end up linking to itself and thus causing an
endless loop for rlist walkers.
So to reproduce just do:
echo 2 > multicast_router; echo 2 > multicast_router;
in a bridge port and let some igmp traffic flow, for me it hangs up
in br_multicast_flood().
Fix this by adding a check in br_multicast_add_router() if the port is
already linked.
The reason this didn't happen before the addition of multicast_router
sysfs entries is because there's a !hlist_unhashed check that prevents
it.
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Fixes: 0909e11758 ("bridge: Add multicast_router sysfs entries")
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the TIPC connection timer expires in a probing state, a
self abort message is supposed to be generated and delivered
to the local socket. This is currently broken, and the abort
message is actually sent out to the peer node with invalid
addressing information. This will cause the link to enter
a constant retransmission state and eventually reset.
We fix this by removing the self-abort message creation and
tear down connection immediately instead.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch the user-specified bridge port was ignored when
deleting an fdb entry and thus one could delete an entry that belonged
to any port.
Example (eth0 and eth1 are br0 ports):
bridge fdb add 00:11:22:33:44:55 dev eth0 master
bridge fdb del 00:11:22:33:44:55 dev eth1 master
(succeeds)
after the patch:
bridge fdb add 00:11:22:33:44:55 dev eth0 master
bridge fdb del 00:11:22:33:44:55 dev eth1 master
RTNETLINK answers: No such file or directory
Based on a patch by Wilson Kok.
Reported-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJVdphLAAoJEP5prqPJtc/HZR0H/j7+UFxotHs+ummTanP3Rbqi
lLBgjzXQDvQeEYhCHzUM4s0dKOQp3arHnO538hB5bONijxoNJkHBkz0urbspLR/f
i9BZRdLd8eiCrXYo4zXM1dZ4xA/xLKX/4sZU/r44wZlcQeLR0VwerZWWd3Zl9hi5
0RGWvENz2FajCxBHaf+TFbr6AVPg7ikWXRpk3s5//adfGYzZMLTpIecrOI3OdtB2
JYrX1FZW2NudtzNfC5vR7g8x4esGzTL7TupdNP0SpxYUTfAkEbLrG+VCbswkYVCs
TL7BElbz5JrfUweWjj/6LJKPFUlCHW3TygBbmHiIl7htyJPllCIpF2gDI+uhSYw=
=JtLU
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.2-20150609' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-05-06
this is a pull request of a two patches for net-next.
The first patch is by Tomas Krcka, he fixes the (currently unused)
register address for acceptance filters. Oliver Hartkopp contributes a
patch for the cangw, where an optional UID is added to reference
routing jobs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
list_del() poisons pointers with special values, no need to overwrite them.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge back net-next to get wireless driver changes (from Kalle)
to be able to create the API change across all trees properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes a bug in hwmp_preq_frame_process where the wrong metric
can be used when forwarding a PREQ. This happens because the code uses
the same metric variable to record the value of the metric to the source
of the PREQ and the value of the metric to the target of the PREQ.
This comes into play when both reply and forward are set which happens
when IEEE80211_PREQ_PROACTIVE_PREP_FLAG is set and when MP_F_DO | MP_F_RF
is set. The original code had a special case to handle the first case
but not the second.
The patch uses distinct variables for the two metrics which makes the
code flow much clearer and removes the need to restore the original
value of metric when forwarding.
Signed-off-by: Alexis Green <agreen@cococorp.com>
CC: Jesse Jones <jjones@cococorp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we notify user space of a new LTK or distribute an LTK to the
remote peer the value passed should be the shortened version so that
it's easy to compare values in various traces. The core spec also sets
the requirements for the shortening/masking as:
"The masking shall be done after generation and before being
distributed, used or stored."
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
- use common Jenkins hash instead of private implementation
- extend internal routing API
- properly re-arrange header files inclusion
- clarify precedence between '&' and '?'
- remove unused ethhdr variable in batadv_gw_dhcp_recipient_get()
- ensure per-VLAN structs are updated upon MAC change
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=u+G3
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Included changes:
- use common Jenkins hash instead of private implementation
- extend internal routing API
- properly re-arrange header files inclusion
- clarify precedence between '&' and '?'
- remove unused ethhdr variable in batadv_gw_dhcp_recipient_get()
- ensure per-VLAN structs are updated upon MAC change
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Until recently, mac80211 overwrote all the statistics it could
provide when getting called, but it now relies on the struct
having been zeroed by the caller. This was always the case in
nl80211, but wext used a static struct which could even cause
values from one device leak to another.
Using a static struct is OK (as even documented in a comment)
since the whole usage of this function and its return value is
always locked under RTNL. Not clearing the struct for calling
the driver has always been wrong though, since drivers were
free to only fill values they could report, so calling this
for one device and then for another would always have leaked
values from one to the other.
Fix this by initializing the structure in question before the
driver method call.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=99691
Cc: stable@vger.kernel.org
Reported-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Reported-by: Alexander Kaltsas <alexkaltsas@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mesh mode there is a race between establishing links and processing
rates and capabilities in beacons. This is very noticeable with slow
beacons (e.g. beacon intervals of 1s) and manifested for us as stations
using minstrel when minstrel_ht should be used. Fixed by changing
mesh_sta_info_init so that it always checks rates and such if it has not
already done so.
Signed-off-by: Alexis Green <agreen@cococorp.com>
CC: Jesse Jones <jjones@cococorp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The csa counter has moved from sdata to beacon/presp but
it is not updated accordingly for mesh and ibss. Fix this.
Fixes: af296bdb8d ("mac80211: move csa counters from sdata to beacon/presp")
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The last hop metric should refer to link cost (this is how
hwmp_route_info_get uses it for example). But in mesh_rx_path_sel_frame
we are not dealing with link cost but with the total cost to the origin
of a PREQ or PREP.
Signed-off-by: Alexis Green <agreen@cococorp.com>
CC: Jesse Jones <jjones@cococorp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channels in 2.4GHz band overlap, this means that if we
send a probe request on channel 1 and then move to channel
2, we will hear the probe response on channel 2. In this
case, the RSSI will be lower than if we had heard it on
the channel on which it was sent (1 in this case).
The scan result ignores those invalid values and the
station last signal should not be updated as well.
In case the scan determines the signal to be invalid turn on
the flag so the station last signal will not be updated with
the value and thus user space probing for NL80211_STA_INFO_SIGNAL
and NL80211_STA_INFO_SIGNAL_AVG will not get this invalid RSSI
value.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There were a few rare cases when upon
authentication failure channel wasn't released.
This could cause stale pointers to remain in
chanctx assigned_vifs after interface removal and
trigger general protection fault later.
This could be triggered, e.g. on ath10k with the
following steps:
1. start an AP
2. create 2 extra vifs on ath10k host
3. connect vif1 to the AP
4. connect vif2 to the AP
(auth fails because ath10k firmware isn't able
to maintain 2 peers with colliding AP mac
addresses across vifs and consequently
refuses sta_info_insert() in
ieee80211_prep_connection())
5. remove the 2 extra vifs
6. goto step 2; at step 3 kernel was crashing:
general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
Modules linked in: ath10k_pci ath10k_core ath
...
Call Trace:
[<ffffffff81a2dabb>] ieee80211_check_combinations+0x22b/0x290
[<ffffffff819fb825>] ? ieee80211_check_concurrent_iface+0x125/0x220
[<ffffffff8180f664>] ? netpoll_poll_disable+0x84/0x100
[<ffffffff819fb833>] ieee80211_check_concurrent_iface+0x133/0x220
[<ffffffff81a0029e>] ieee80211_open+0x3e/0x80
[<ffffffff817f2d26>] __dev_open+0xb6/0x130
[<ffffffff817f3051>] __dev_change_flags+0xa1/0x170
...
RIP [<ffffffff81a23140>] ieee80211_chanctx_radar_detect+0xa0/0x170
(gdb) l * ieee80211_chanctx_radar_detect+0xa0
0xffffffff81a23140 is in ieee80211_chanctx_radar_detect (/devel/src/linux/net/mac80211/util.c:3182).
3177 */
3178 WARN_ON(ctx->replace_state == IEEE80211_CHANCTX_REPLACES_OTHER &&
3179 !list_empty(&ctx->assigned_vifs));
3180
3181 list_for_each_entry(sdata, &ctx->assigned_vifs, assigned_chanctx_list)
3182 if (sdata->radar_required)
3183 radar_detect |= BIT(sdata->vif.bss_conf.chandef.width);
3184
3185 return radar_detect;
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The conversion to the fast-xmit path lost proper aggregation session
timeout handling - the last_tx wasn't set on that path and the timer
would therefore incorrectly tear down the session periodically (with
those drivers/rate control algorithms that have a timeout.)
In case of iwlwifi, this was every 5 seconds and caused significant
throughput degradation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SCO/eSCO link is supported by BR/EDR controller, it is
suitable to move them under BT_BREDR config option
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The return value of l2cap_recv_acldata() and sco_recv_scodata()
are not used, then change it to return void
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This call was used before we aligned our code with the wireless code base. We
are wanted to handle this in the err: code path. Which would actually not work
because the WARN_ON() macro would reset the res value to 0 and thus we would
never hit err:. Removing it makes the code do what we actually intend.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Similar to referencing iptables rules by their line number this UID allows to
reference created routing jobs, e.g. to alter configured data modifications.
The UID is an optional non-zero value which can be provided at routing job
creation time. When the UID is set the UID replaces the data modification
configuration as job identification attribute e.g. at job removal time.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The encryption key size for LTKs is supposed to be applied only at the
moment of encryption. When generating a Link Key (using LE SC) from
the LTK the full non-shortened value should be used. This patch
modifies the code to always keep the full value around and only apply
the key size when passing the value to HCI.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Vendor commands are passed from userspace through the
NFC_CMD_VENDOR netlink command, allowing driver and hardware
specific operations implementations like for example RF tuning
or production line calibration.
Drivers will associate a set of vendor commands to a vendor
id, which could typically be an OUI. The netlink kernel
implementation will try to match the received vendor id
and sub command attributes with the registered ones. When
such match is found, the driver defined sub command routine
is called.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When closing the device some data (proprietary commands)
might be sent. The core state machine needs to be set for
correct command execution.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Handle allowing to send proprietary nci commands anywhere in the nci
state machine.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some device may need to execute some proprietary commands
in order to "wake-up"; Before the nci state initialization.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
setup was executed in any case, even if NCI_RESET failed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow for drivers to explicitly define handlers for each
proprietary notifications and responses they expect to support.
Reviewed-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Several of these goto exit; uses should be direct returns
as skb is not yet initialized by nci_hci_get_param().
Miscellanea:
o Use !memcmp instead of memcmp() == 0
o Remove unnecessary goto from if () {... goto exit;} else {...} exit:
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Commit 70008aa50e ("skbuff: convert to skb_orphan_frags") replaced
open coded tests of SKBTX_DEV_ZEROCOPY and skb_copy_ubufs with calls
to helper function skb_orphan_frags. Apply that to the last remaining
open coded site.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP encapsulation is broken on IPv6. This is because the logic to resubmit
the nexthdr is inverted, checking for a ret value > 0 instead of < 0. Also,
the resubmit label is in the wrong position since we already get the
nexthdr value when performing decapsulation. In addition the skb pull is no
longer necessary either.
This changes the return value check to look for < 0, using it for the
nexthdr on the next iteration, and moves the resubmit label to the proper
location.
With these changes the v6 code now matches what we do in the v4 ip input
code wrt resubmitting when decapsulating.
Signed-off-by: Josh Hunt <johunt@akamai.com>
Acked-by: "Tom Herbert" <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory pointed to by idev->stats.icmpv6msgdev,
idev->stats.icmpv6dev and idev->stats.ipv6 can each be used in an RCU
read context without taking a reference on idev. For example, through
IP6_*_STATS_* calls in ip6_rcv. These memory blocks are freed without
waiting for an RCU grace period to elapse. This could lead to the
memory being written to after it has been freed.
Fix this by using call_rcu to free the memory used for stats, as well
as idev after an RCU grace period has elapsed.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the initial setup stage of a controller, the low-level transport
is actually active. This means that HCI_UP is true. To avoid toggling
the transport off and back on again for normal operation the kernel
holds a grace period with HCI_AUTO_OFF that will turn the low-level
transport off in case no user is present.
The idea of the grace period is important to avoid having to initialize
all of the controller twice. So legacy ioctl and the new management
interface knows how to clear this grace period and then start normal
operation.
For the user channel operation this grace period has not been taken into
account which results in the problem that HCI_UP and HCI_AUTO_OFF are
set and the kernel will return EBUSY. However from a system point of
view the controller is ready to be grabbed by either the ioctl, the
management interface or the user channel.
This patch brings the user channel to the same level as the other two
entries for operating a controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
As Alexander Duyck pointed out that:
struct tnode {
...
struct key_vector kv[1];
}
The kv[1] member of struct tnode is an arry that refernced by
a null pointer will not crash the system, like this:
struct tnode *p = NULL;
struct key_vector *kv = p->kv;
As such p->kv doesn't actually dereference anything, it is simply a
means for getting the offset to the array from the pointer p.
This patch make the code more regular to avoid making people feel
odd when they look at the code.
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_fdb_update() can be called in process context in the following way:
br_fdb_add() -> __br_fdb_add() -> br_fdb_update() (if NTF_USE flag is set)
so we need to disable softirqs because there are softirq users of the
hash_lock. One easy way to reproduce this is to modify the bridge utility
to set NTF_USE, enable stp and then set maxageing to a low value so
br_fdb_cleanup() is called frequently and then just add new entries in
a loop. This happens because br_fdb_cleanup() is called from timer/softirq
context. The spin locks in br_fdb_update were _bh before commit f8ae737dee
("[BRIDGE]: forwarding remove unneeded preempt and bh diasables")
and at the time that commit was correct because br_fdb_update() couldn't be
called from process context, but that changed after commit:
292d139898 ("bridge: add NTF_USE support")
Using local_bh_disable/enable around br_fdb_update() allows us to keep
using the spin_lock/unlock in br_fdb_update for the fast-path.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: 292d139898 ("bridge: add NTF_USE support")
Signed-off-by: David S. Miller <davem@davemloft.net>
The mpls device is used in an RCU read context without a lock being
held. As the memory is freed without waiting for the RCU grace period
to elapse, the freed memory could still be in use.
Address this by using kfree_rcu to free the memory for the mpls device
after the RCU grace period has elapsed.
Fixes: 03c57747a7 ("mpls: Per-device MPLS state")
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_fdb_update() can be called in process context in the following way:
br_fdb_add() -> __br_fdb_add() -> br_fdb_update() (if NTF_USE flag is set)
so we need to use spin_lock_bh because there are softirq users of the
hash_lock. One easy way to reproduce this is to modify the bridge utility
to set NTF_USE, enable stp and then set maxageing to a low value so
br_fdb_cleanup() is called frequently and then just add new entries in
a loop. This happens because br_fdb_cleanup() is called from timer/softirq
context. These locks were _bh before commit f8ae737dee
("[BRIDGE]: forwarding remove unneeded preempt and bh diasables")
and at the time that commit was correct because br_fdb_update() couldn't be
called from process context, but that changed after commit:
292d139898 ("bridge: add NTF_USE support")
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: 292d139898 ("bridge: add NTF_USE support")
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 and IPv6 share same implementation of get_cookie_sock(),
and there is no point inlining it.
We add tcp_ prefix to the common helper name and export it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC address of the soft-interface is used to initialise
the "non-purge" TT entry of each existing VLAN. Therefore
when the user invokes ndo_set_mac_address() all the
"non-purge" TT entries have to be updated, not only the one
belonging to the non-tagged network.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The header files could not be build indepdent from each other. This is
happened because headers didn't include the files for things they've used.
This was problematic because the success of a build depended on the
knowledge about the right order of local includes.
Also source files were not including everything they've used explicitly.
Instead they required that transitive includes are always stable. This is
problematic because some transitive includes are not obvious, depend on
config settings and may not be stable in the future.
The order for include blocks are:
* primary headers (main.h and the *.h file of a *.c file)
* global linux headers
* required local headers
* extra forward declarations for pointers in function/struct declarations
The only exceptions are linux/bitops.h and linux/if_ether.h in packet.h.
This header file is shared with userspace applications like batctl and must
therefore build together with userspace applications. The header
linux/bitops.h is not part of the uapi headers and linux/if_ether.h
conflicts with the musl implementation of netinet/if_ether.h. The
maintainers rejected the use of __KERNEL__ preprocessor checks and thus
these two headers are only in main.h. All files using packet.h first have
to include main.h to work correctly.
Reported-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This API has to be used to let any routing protocol free
neighbor specific allocated resources
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Some mesh attributes are behind substructs in the
batadv_priv object and for this reason the name cannot be
used anymore to refer to them.
This patch allows to specify the variable name where the
attribute is stored inside batadv_priv instead of using the
name
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
An unoptimized version of the Jenkins one-at-a-time hash function is used
and partially copied all over the code wherever an hashtable is used.
Instead the optimized version shared between the whole kernel should be
used to reduce code duplication and use better optimized code.
Only the DAT code must use the old implementation because it is used as
distributed hash function which has to be common for all nodes.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
allow programs read/write skb->mark, tc_index fields and
((struct qdisc_skb_cb *)cb)->data.
mark and tc_index are generically useful in TC.
cb[0]-cb[4] are primarily used to pass arguments from one
program to another called via bpf_tail_call() which can
be seen in sockex3_kern.c example.
All fields of 'struct __sk_buff' are readable to socket and tc_cls_act progs.
mark, tc_index are writeable from tc_cls_act only.
cb[0]-cb[4] are writeable by both sockets and tc_cls_act.
Add verifier tests and improve sample code.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eBPF programs attached to ingress and egress qdiscs see inconsistent skb->data.
For ingress L2 header is already pulled, whereas for egress it's present.
This is known to program writers which are currently forced to use
BPF_LL_OFF workaround.
Since programs don't change skb internal pointers it is safe to do
pull/push right around invocation of the program and earlier taps and
later pt->func() will not be affected.
Multiple taps via packet_rcv(), tpacket_rcv() are doing the same trick
around run_filter/BPF_PROG_RUN even if skb_shared.
This fix finally allows programs to use optimized LD_ABS/IND instructions
without BPF_LL_OFF for higher performance.
tc ingress + cls_bpf + samples/bpf/tcbpf1_kern.o
w/o JIT w/JIT
before 20.5 23.6 Mpps
after 21.8 26.6 Mpps
Old programs with BPF_LL_OFF will still work as-is.
We can now undo most of the earlier workaround commit:
a166151cbe ("bpf: fix bpf helpers to use skb->mac_header relative offsets")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For same reasons than in commit 12e25e1041 ("tcp: remove redundant
checks"), we can remove redundant checks done for timewait sockets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the virtual interface structure from sub if data
struct, because it isn't used anywhere. This structure could be useful
for give per interface information at softmac driver layer. Nevertheless
there exist no use case currently and it contains the interface type
information currently. This information is also stored inside wpan dev
which is now used to check on the wpan dev interface type.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When an application needs to force a source IP on an active TCP socket
it has to use bind(IP, port=x).
As most applications do not want to deal with already used ports, x is
often set to 0, meaning the kernel is in charge to find an available
port.
But kernel does not know yet if this socket is going to be a listener or
be connected.
It has very limited choices (no full knowledge of final 4-tuple for a
connect())
With limited ephemeral port range (about 32K ports), it is very easy to
fill the space.
This patch adds a new SOL_IP socket option, asking kernel to ignore
the 0 port provided by application in bind(IP, port=0) and only
remember the given IP address.
The port will be automatically chosen at connect() time, in a way
that allows sharing a source port as long as the 4-tuples are unique.
This new feature is available for both IPv4 and IPv6 (Thanks Neal)
Tested:
Wrote a test program and checked its behavior on IPv4 and IPv6.
strace(1) shows sequences of bind(IP=127.0.0.2, port=0) followed by
connect().
Also getsockname() show that the port is still 0 right after bind()
but properly allocated after connect().
socket(PF_INET, SOCK_STREAM, IPPROTO_IP) = 5
setsockopt(5, SOL_IP, IP_BIND_ADDRESS_NO_PORT, [1], 4) = 0
bind(5, {sa_family=AF_INET, sin_port=htons(0), sin_addr=inet_addr("127.0.0.2")}, 16) = 0
getsockname(5, {sa_family=AF_INET, sin_port=htons(0), sin_addr=inet_addr("127.0.0.2")}, [16]) = 0
connect(5, {sa_family=AF_INET, sin_port=htons(53174), sin_addr=inet_addr("127.0.0.3")}, 16) = 0
getsockname(5, {sa_family=AF_INET, sin_port=htons(38050), sin_addr=inet_addr("127.0.0.2")}, [16]) = 0
IPv6 test :
socket(PF_INET6, SOCK_STREAM, IPPROTO_IP) = 7
setsockopt(7, SOL_IP, IP_BIND_ADDRESS_NO_PORT, [1], 4) = 0
bind(7, {sa_family=AF_INET6, sin6_port=htons(0), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, 28) = 0
getsockname(7, {sa_family=AF_INET6, sin6_port=htons(0), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, [28]) = 0
connect(7, {sa_family=AF_INET6, sin6_port=htons(57300), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, 28) = 0
getsockname(7, {sa_family=AF_INET6, sin6_port=htons(60964), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, [28]) = 0
I was able to bind()/connect() a million concurrent IPv4 sockets,
instead of ~32000 before patch.
lpaa23:~# ulimit -n 1000010
lpaa23:~# ./bind --connect --num-flows=1000000 &
1000000 sockets
lpaa23:~# grep TCP /proc/net/sockstat
TCP: inuse 2000063 orphan 0 tw 47 alloc 2000157 mem 66
Check that a given source port is indeed used by many different
connections :
lpaa23:~# ss -t src :40000 | head -10
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 0 127.0.0.2:40000 127.0.202.33:44983
ESTAB 0 0 127.0.0.2:40000 127.2.27.240:44983
ESTAB 0 0 127.0.0.2:40000 127.2.98.5:44983
ESTAB 0 0 127.0.0.2:40000 127.0.124.196:44983
ESTAB 0 0 127.0.0.2:40000 127.2.139.38:44983
ESTAB 0 0 127.0.0.2:40000 127.1.59.80:44983
ESTAB 0 0 127.0.0.2:40000 127.3.6.228:44983
ESTAB 0 0 127.0.0.2:40000 127.0.38.53:44983
ESTAB 0 0 127.0.0.2:40000 127.1.197.10:44983
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hci close method needs to know if we are in user channel context.
Only add the index to mgmt once close is performed.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
addr can be NULL and it should not be dereferenced before NULL checking.
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In flow dissector if an MPLS header contains an entropy label this is
saved in the new keyid field of flow_keys. The entropy label is
then represented in the flow hash function input.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In flow dissector if a GRE header contains a keyid this is saved in the
new keyid field of flow_keys. The GRE keyid is then represented
in the flow hash function input.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In flow_dissector set the flow label in flow_keys for IPv6. This also
removes the shortcircuiting of flow dissection when a non-zero label
is present, the flow label can be considered to provide additional
entropy for a hash.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In flow_dissector set vlan_id in flow_keys when VLAN is found.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need to return the IPv6 address hash as part of flow keys.
In general, using the IPv6 address hash is risky in a hash value
since the underlying use of xor provides no entropy. If someone
really needs the hash value they can get it from the full IPv6
addresses in flow keys (e.g. from flow_get_u32_src).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds full IPv6 addresses into flow_keys and uses them as
input to the flow hash function. The implementation supports either
IPv4 or IPv6 addresses in a union, and selector is used to determine
how may words to input to jhash2.
We also add flow_get_u32_dst and flow_get_u32_src functions which are
used to get a u32 representation of the source and destination
addresses. For IPv6, ipv6_addr_hash is called. These functions retain
getting the legacy values of src and dst in flow_keys.
With this patch, Ethertype and IP protocol are now included in the
flow hash input.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes flow hashing to use jhash2 over the flow_keys
structure instead just doing jhash_3words over src, dst, and ports.
This method will allow us take more input into the hashing function
so that we can include full IPv6 addresses, VLAN, flow labels etc.
without needing to resort to xor'ing which makes for a poor hash.
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
key_basic is set twice in __skb_flow_dissect which seems unnecessary.
Remove second one.
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do break when we see routing flag or a non-zero version number in GRE
header.
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bi-directional RPC support means code in svcrdma.ko invokes a bit of
code in xprtrdma.ko, and vice versa. To avoid loader/linker loops,
merge the server and client side modules together into a single
module.
When backchannel capabilities are added, the combined module will
register all needed transport capabilities so that Upper Layer
consumers automatically have everything needed to create a
bi-directional transport connection.
Module aliases are added for backwards compatibility with user
space, which still may expect svcrdma.ko or xprtrdma.ko to be
present.
This commit reverts commit 2e8c12e1b7 ("xprtrdma: add separate
Kconfig options for NFSoRDMA client and server support") and
provides a single CONFIG option for enabling the new module.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The server and client maximum are architecturally independent.
Allow changing one without affecting the other.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
At the 2015 LSF/MM, it was requested that memory allocation
call sites that request GFP_KERNEL allocations in a loop should be
annotated with __GFP_NOFAIL.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Fields in struct rpcrdma_msg are __be32. Don't byte-swap these
fields when decoding RPC calls and then swap them back for the
reply. For the most part, they can be left alone.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
In send_write_chunks(), we have:
for (xdr_off = rqstp->rq_res.head[0].iov_len, chunk_no = 0;
xfer_len && chunk_no < arg_ary->wc_nchunks;
chunk_no++) {
. . .
}
Note that arg_ary->wc_nchunk is in network byte-order. For the
comparison to work correctly, both have to be in native byte-order.
In send_reply_chunks, we have:
write_len = min(xfer_len, htonl(ch->rs_length));
xfer_len is in native byte-order, and ch->rs_length is in
network byte-order. be32_to_cpu() is the correct byte swap
for ch->rs_length.
As an additional clean up, replace ntohl() with be32_to_cpu() in
a few other places.
This appears to address a problem with large rsize hangs while
using PHYSICAL memory registration. I suspect that is the only
registration mode that uses more than one chunk element.
BugLink: https://bugzilla.linux-nfs.org/show_bug.cgi?id=248
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
fix build error:
net/core/filter.c: In function 'bpf_clone_redirect':
net/core/filter.c:1429:18: error: 'struct sk_buff' has no member named 'tc_verd'
if (G_TC_AT(skb2->tc_verd) & AT_INGRESS)
Fixes: 3896d655f4 ("bpf: introduce bpf_clone_redirect() helper")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will export the supported commands by the devices
to the userspace. This will be useful to check if HardMAC
drivers can support a specific command or not.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The AF_IEEE802154 sockaddr looks like this:
struct sockaddr_ieee802154 {
sa_family_t family; /* AF_IEEE802154 */
struct ieee802154_addr_sa addr;
};
struct ieee802154_addr_sa {
int addr_type;
u16 pan_id;
union {
u8 hwaddr[IEEE802154_ADDR_LEN];
u16 short_addr;
};
};
On most architectures there will be implicit structure padding here,
in two different places:
* In struct sockaddr_ieee802154, two bytes of padding between 'family'
(unsigned short) and 'addr', so that 'addr' starts on a four byte
boundary.
* In struct ieee802154_addr_sa, two bytes at the end of the structure,
to make the structure 16 bytes.
When calling recvmsg(2) on a PF_IEEE802154 SOCK_DGRAM socket, the
ieee802154 stack constructs a struct sockaddr_ieee802154 on the
kernel stack without clearing these padding fields, and, depending
on the addr_type, between four and ten bytes of uncleared kernel
stack will be copied to userspace.
We can't just insert two 'u16 __pad's in the right places and zero
those before copying an address to userspace, as not all architectures
insert this implicit padding -- from a quick test it seems that avr32,
cris and m68k don't insert this padding, while every other architecture
that I have cross compilers for does insert this padding.
The easiest way to plug the leak is to just memset the whole struct
sockaddr_ieee802154 before filling in the fields we want to fill in,
and that's what this patch does.
Cc: stable@vger.kernel.org
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch make to use the same naming convention that mac802154
tracing follows and fixes the format specifier for extended addr.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Xen virtual network driver has higher latency than a physical NIC.
Having only 128K as limit for TSQ introduced 30% regression in guest
throughput.
This patch raises the limit to 256K. This reduces the regression to 8%.
This buys us more time to work out a proper solution in the long run.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_v4_rcv() checks the following before calling tcp_v4_do_rcv():
if (th->doff < sizeof(struct tcphdr) / 4)
goto bad_packet;
if (!pskb_may_pull(skb, th->doff * 4))
goto discard_it;
So following check in tcp_v4_do_rcv() is redundant
and "goto csum_err;" is wrong anyway.
if (skb->len < tcp_hdrlen(skb) || ...)
goto csum_err;
A second check can be removed after no_tcp_socket label for same reason.
Same tests can be removed in tcp_v6_do_rcv()
Note : short tcp frames are not properly accounted in tcpInErrs MIB,
because pskb_may_pull() failure simply drops incoming skb, we might
fix this in a separate patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
421b3885bf "udp: ipv4: Add udp early
demux" introduced a regression that allowed sockets bound to INADDR_ANY
to receive packets from multicast groups that the socket had not joined.
For example a socket that had joined 224.168.2.9 could also receive
packets from 225.168.2.9 despite not having joined that group if
ip_early_demux is enabled.
Fix this by calling ip_check_mc_rcu() in udp_v4_early_demux() to verify
that the multicast packet is indeed ours.
Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Reported-by: Yurij M. Plotnikov <Yurij.Plotnikov@oktetlabs.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clarify in documentation and code that IPV4 FIB add operation is used for
both adding a new FIB entry to the device and for modifying an existing FIB
entry on the device.
Also, remove left-over references to ipv4_fib ops and replace with details
on SWITCHDEV_PORT_IPV4_FIB object.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
- code re-arrangement for better reading and understanding
- code style fixups
- comments corrections
- remove unnecessary NULL check in batadv_iv_ogm_update_seqnos()
- make boolean functions explicitly return a bool result
- remove unnecessary variables in algo_register() and algo_select()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=m9Yd
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
pull request: batman-adv 20150603
here you have our second batch of patches intended for net-next.
In this patchset you won't find any new features, but quite some code
cleanup work, a bunch of code style fixes and also comments corrections
by Markus Pargmann.
Moreover you have a patch from Sven Eckelmann removing an unnecessary
NULL check in batadv_iv_ogm_update_seqnos().
Please pull or let me know of any problem!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow eBPF programs attached to classifier/actions to call
bpf_clone_redirect(skb, ifindex, flags) helper which will
mirror or redirect the packet by dynamic ifindex selection
from within the program to a target device either at ingress
or at egress. Can be used for various scenarios, for example,
to load balance skbs into veths, split parts of the traffic
to local taps, etc.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, openvswitch tries to disable LRO from the user space. This does
not work correctly when the device added is a vlan interface, though.
Instead of dealing with possibly complex stacked cross name space relations
in the user space, do the same as bridging does and call dev_disable_lro in
the kernel.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
svc_rdma_xdr_decode_deferred_req() indexes an array with an
un-byte-swapped value off the wire. Fortunately this function
isn't used anywhere, so simply remove it.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
We can avoid this indirect return variable by directly returning the
error values.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Declare the returntype of batadv_compare_eth as bool.
The function called inside this helper function
(ether_addr_equal_unaligned) also uses bool as return value, so there is
no need to return int.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
It is much clearer to see a bool type as return value than 'int' for
functions that are supposed to return true or false.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
orig_ifinfo is dereferenced multiple times in batadv_iv_ogm_update_seqnos
before the check for NULL is done. The function also exists at the
beginning when orig_ifinfo would have been NULL. This makes the check at
the end unnecessary and only confuses the reader/code analyzers.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
batadv_orig_bat_iv->bcast_own is actually not a bitfield, it is an
array. Adjust the comment accordingly.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This is a small copy paste fix for batadv_ing_buffer_avg.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The kernel coding style says, that there should not be multiple
assignments in one row.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
CodingStyle describes that either none or both branches of a conditional
have to have brackets.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
It is just a bit easier to put the error handling at one place and let
multiple error paths use the same calls.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The naming convention is to always have the flags prefixed with
IEEE80211_HW_ so they're 'namespaced', make this flag follow it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are no drivers setting IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE
or IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE, so any code using the
two flags is dead; it's also exceedingly unlikely that any new driver
could ever need to set these flags.
The wcn36xx code is almost certainly broken, but this preserves the
previous behaviour.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch sets the acknowledge request bit inside the 802.15.4 mac
header when frame retries is 0 or above. The other frame retries value
which is -1 indicates that the transmitter doesn't care about an
acknowledge frame which will be ignored after transmitting if the node
sends anyway an ack frame after receiving. This is currently unnecessary
traffic if the max frame retries parameter is -1.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BUG_ON at line 452/453 is triggered in function rds_send_xmit.
441 while (ret) {
442 tmp = min_t(int, ret, sg->length -
443 conn->c_xmit_data_off);
444 conn->c_xmit_data_off += tmp;
445 ret -= tmp;
446 if (conn->c_xmit_data_off == sg->length) {
447 conn->c_xmit_data_off = 0;
448 sg++;
449 conn->c_xmit_sg++;
450 if (ret != 0 && conn->c_xmit_sg == rm->data.op_nents)
451 printk(KERN_ERR "conn %p rm %p sg %p ret %d\n", conn, rm, sg, ret);
452 BUG_ON(ret != 0 &&
453 conn->c_xmit_sg == rm->data.op_nents);
454 }
455 }
it is complaining the total sent length is bigger that we want to send.
rds_ib_xmit() is wrong for the second entry for the same rds_message returning
wrong value.
the sg and off passed by rds_send_xmit to rds_ib_xmit is based on
scatterlist.offset/length, but the rds_ib_xmit action is based on
scatterlist.dma_address/dma_length. in case dma_length is larger than length
there is problem. for the 2nd and later entries of rds_ib_xmit for same
rds_message, at least one of the following two is wrong:
1) the scatterlist to start with, the choosen one can far beyond the correct
one.
2) the offset to start with within the scatterlist.
fix:
add op_dmasg and op_dmaoff to rm_data_op structure indicating the scatterlist
and offset within the it to start with for rds_ib_xmit respectively. op_dmasg
and op_dmaoff are initialized to zero when doing dma mapping for the first see
of the message and are changed when filling send slots.
the same applies to rds_iw_xmit too.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Even if the pointers are really only accessible to root and used
pretty much only by wpa_supplicant, this is still not great; even
for debugging it'd be easier to have something that's easier to
read and guaranteed to never get reused.
With the recent change to make mac80211 create an ack_skb for the
mgmt-tx path this becomes possible, only the client probe method
needs to also allocate an ack_skb, and we can store the cookie in
that skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we return the TX status for an nl80211 mgmt TX SKB, we
should also return the original frame with the status to
allow userspace to match up the submission (it could also
use the cookie but both ways are permissible.)
As TX SKBs could be encrypted, at least in the case of ANQP
while associated with the AP, copy the original SKB, store
it with an ACK frame ID and restructure the status path to
use that to return status with the original SKB. Otherwise,
userspace (in particular wpa_supplicant) will get confused.
Reported-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For drivers supporting TSO or similar features, but that still have
PN assignment in software, there's a need to have some memory to
store the current PN value. As mac80211 already stores this and it's
somewhat complicated to add a per-driver area to the key struct (due
to the dynamic sizing thereof) it makes sense to just move the TX PN
to the keyconf, i.e. the public part of the key struct.
As TKIP is more complicated and we won't able to offload it in this
way right now (fast-xmit is skipped for TKIP unless the HW does it
all, and our hardware needs MMIC calculation in software) I've not
moved that for now - it's possible but requires exposing a lot of
the internal TKIP state.
As an bonus side effect, we can remove a lot of code by assuming the
keyseq struct has a certain layout - with BUILD_BUG_ON to verify it.
This might also improve performance, since now TX and RX no longer
share a cacheline.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fix for net
The following patch reverts the ebtables chunk that enforces counters that was
introduced in the recently applied d26e2c9ffa ('Revert "netfilter: ensure
number of counters is >0 in do_replace()"') since this breaks ebtables.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently rely on the PMTU discovery of xfrm.
However if a packet is localy sent, the PMTU mechanism
of xfrm tries to to local socket notification what
might not work for applications like ping that don't
check for this. So add pmtu handling to vti6_xmit to
report MTU changes immediately.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If new optional attribute OVS_USERSPACE_ATTR_ACTIONS is added to an
OVS_ACTION_ATTR_USERSPACE action, then include the datapath actions
in the upcall.
This Directly associates the sampled packet with the path it takes
through the virtual switch. Path information currently includes mangling,
encapsulation and decapsulation actions for tunneling protocols GRE,
VXLAN, Geneve, MPLS and QinQ, but this extension requires no further
changes to accommodate datapath actions that may be added in the
future.
Adding path information enhances visibility into complex virtual
networks.
Signed-off-by: Neil McKee <neil.mckee@inmon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we scan a packet for GRO processing, we want to see the most
common packet types in the front of the offload_base list.
So add a priority field so we can handle this properly.
IPv4/IPv6 get the highest priority with the implicit zero priority
field.
Next comes ethernet with a priority of 10, and then we have the MPLS
types with a priority of 15.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Suggested-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit f96dee13b8.
It isn't right, ethtool is meant to manage one PHY instance
per netdevice at a time, and this is selected by the SET
command. Therefore by definition the GET command must only
return the settings for the configured and selected PHY.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This partially reverts commit 1086bbe97a ("netfilter: ensure number of
counters is >0 in do_replace()") in net/bridge/netfilter/ebtables.c.
Setting rules with ebtables does not work any more with 1086bbe97a place.
There is an error message and no rules set in the end.
e.g.
~# ebtables -t nat -A POSTROUTING --src 12:34:56:78:9a:bc -j DROP
Unable to update the kernel. Two possible causes:
1. Multiple ebtables programs were executing simultaneously. The ebtables
userspace tool doesn't by default support multiple ebtables programs
running
Reverting the ebtables part of 1086bbe97a makes this work again.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When trying to associate, the AP could send a deauth frame instead.
Currently mac80211 drops that frame and doesn't report it to the
supplicant, which, in some versions and/or in certain circumstances
will simply keep trying to associate over and over again instead of
trying authentication again.
Fix this by reacting to deauth frames while associating, reporting
them to the supplicant and dropping the association attempt (which
is bound to fail.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While shuffling some code around, dsa_switch_setup_one() was introduced,
and it was modified to return either an error code using ERR_PTR() or a
NULL pointer when running out of memory or failing to setup a switch.
This is a problem for its caler: dsa_switch_setup() which uses IS_ERR()
and expects to find an error code, not a NULL pointer, so we still try
to proceed with dsa_switch_setup() and operate on invalid memory
addresses. This can be easily reproduced by having e.g: the bcm_sf2
driver built-in, but having no such switch, such that drv->setup will
fail.
Fix this by using PTR_ERR() consistently which is both more informative
and avoids for the caller to use IS_ERR_OR_NULL().
Fixes: df197195a5 ("net: dsa: split dsa_switch_setup into two functions")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux 3.17 and earlier are explicitly engineered so that if the app
doesn't specifically request a CC module on a listener before the SYN
arrives, then the child gets the system default CC when the connection
is established. See tcp_init_congestion_control() in 3.17 or earlier,
which says "if no choice made yet assign the current value set as
default". The change ("net: tcp: assign tcp cong_ops when tcp sk is
created") altered these semantics, so that children got their parent
listener's congestion control even if the system default had changed
after the listener was created.
This commit returns to those original semantics from 3.17 and earlier,
since they are the original semantics from 2007 in 4d4d3d1e8 ("[TCP]:
Congestion control initialization."), and some Linux congestion
control workflows depend on that.
In summary, if a listener socket specifically sets TCP_CONGESTION to
"x", or the route locks the CC module to "x", then the child gets
"x". Otherwise the child gets current system default from
net.ipv4.tcp_congestion_control. That's the behavior in 3.17 and
earlier, and this commit restores that.
Fixes: 55d8694fa8 ("net: tcp: assign tcp cong_ops when tcp sk is created")
Cc: Florian Westphal <fw@strlen.de>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Glenn Judd <glenn.judd@morganstanley.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The currently attached transport for a PF_RDS socket may be obtained
from user space by invoking getsockopt(2) using the SO_RDS_TRANSPORT
option at the SOL_RDS level. The integer optval returned will be one
of the RDS_TRANS_* constants defined in linux/rds.h.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An application may deterministically attach the underlying transport for
a PF_RDS socket by invoking setsockopt(2) with the SO_RDS_TRANSPORT
option at the SOL_RDS level. The integer argument to setsockopt must be
one of the RDS_TRANS_* transport types, e.g., RDS_TRANS_TCP. The option
must be specified before invoking bind(2) on the socket, and may only
be used once on the socket. An attempt to set the option on a bound
socket, or to invoke the option after a successful SO_RDS_TRANSPORT
attachment, will return EOPNOTSUPP.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User space applications that desire to explicitly select the
underlying transport for a PF_RDS socket may do so by using the
SO_RDS_TRANSPORT socket option at the SOL_RDS level before bind().
The integer argument provided to the socket option would be one
of the RDS_TRANS_* values, e.g., RDS_TRANS_TCP. This commit exports
the constant values need by such applications via <linux/rds.h>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As this is already exported from tracing side via commit d9847d310a
("tracing: Allow BPF programs to call bpf_ktime_get_ns()"), we might
as well want to move it to the core, so also networking users can make
use of it, e.g. to measure diffs for certain flows from ingress/egress.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have two problems in UDP stack related to bogus checksums :
1) We return -EAGAIN to application even if receive queue is not empty.
This breaks applications using edge trigger epoll()
2) Under UDP flood, we can loop forever without yielding to other
processes, potentially hanging the host, especially on non SMP.
This patch is an attempt to make things better.
We might in the future add extra support for rt applications
wanting to better control time spent doing a recv() in a hostile
environment. For example we could validate checksums before queuing
packets in socket receive queue.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
more things for -next:
* disconnect TDLS stations on CSA to avoid issues
* fix a memory leak introduced in a recent commit
* switch rfkill and cfg80211 to PM ops
* in an unlikely scenario, prevent a bookkeeping
value to get corrupted leading to dropped packets
* fix a crash in VLAN assignment
* switch rfkill-gpio to more modern gpiod API
* send disconnected event to userspace with proper
local/remote indication
-----BEGIN PGP SIGNATURE-----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=KmwY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
As we get closer to the merge window, here are a few
more things for -next:
* disconnect TDLS stations on CSA to avoid issues
* fix a memory leak introduced in a recent commit
* switch rfkill and cfg80211 to PM ops
* in an unlikely scenario, prevent a bookkeeping
value to get corrupted leading to dropped packets
* fix a crash in VLAN assignment
* switch rfkill-gpio to more modern gpiod API
* send disconnected event to userspace with proper
local/remote indication
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Refuse to allow setting an EUI-64 group address as an interface
address, as those are not valid station addresses.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
- checkpatch fixes
- code cleanup
- debugfs component is now compiled only if DEBUG_FS is selected
- update copyright years
- disable by default not-so-user-safe features
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=2UBm
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Included changes:
- checkpatch fixes
- code cleanup
- debugfs component is now compiled only if DEBUG_FS is selected
- update copyright years
- disable by default not-so-user-safe features
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove automatic variable 'err' in register_netevent_notifier() and
return the result of atomic_notifier_chain_register() directly.
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next, they are:
1) default CONFIG_NETFILTER_INGRESS to y for easier compile-testing of all
options.
2) Allow to bind a table to net_device. This introduces the internal
NFT_AF_NEEDS_DEV flag to perform a mandatory check for this binding.
This is required by the next patch.
3) Add the 'netdev' table family, this new table allows you to create ingress
filter basechains. This provides access to the existing nf_tables features
from ingress.
4) Kill unused argument from compat_find_calc_{match,target} in ip_tables
and ip6_tables, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete jump to a label on the next line, when that label is not
used elsewhere.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier l;
@@
-if (...) goto l;
-l:
// </smpl>
Also remove the unnecessary ret variable.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_multicast_query_expired() querier argument is a pointer to
a struct bridge_mcast_querier :
struct bridge_mcast_querier {
struct br_ip addr;
struct net_bridge_port __rcu *port;
};
Intent of the code was to clear port field, not the pointer to querier.
Fixes: 2cd4143192 ("bridge: memorize and export selected IGMP/MLD querier port")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Cc: Linus Lüssing <linus.luessing@web.de>
Cc: Steinar H. Gunderson <sesse@samfundet.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-05-28
Here's a set of patches intended for 4.2. The majority of the changes
are on the 802.15.4 side of things rather than Bluetooth related:
- All sorts of cleanups & fixes to ieee802154 and related drivers
- Rework of tx power support in ieee802154 and its drivers
- Support for setting ieee802154 tx power through nl802154
- New IDs for the btusb driver
- Various cleanups & smaller fixes to btusb
- New btrtl driver for Realtec devices
- Fix suspend/resume for Realtek devices
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As sock refcnt is taken when sock timer is started in
sk_reset_timer(), the sock refcnt should be put when sock timer
to be deleted is in pending state no matter what "probing_state"
value of tipc sock is.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
classic BPF already exposes skb->dev->ifindex via SKF_AD_IFINDEX extension.
Allow eBPF program to access it as well. Note that classic aborts execution
of the program if 'skb->dev == NULL' (which is inconvenient for program
writers), whereas eBPF returns zero in such case.
Also expose the 'skb_iif' field, since programs triggered by redirected
packet need to known the original interface index.
Summary:
__skb->ifindex -> skb->dev->ifindex
__skb->ingress_ifindex -> skb->skb_iif
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is similar to b1cb59cf2efe(net: sysctl_net_core: check SNDBUF
and RCVBUF for min length). I don't think too small values can cause
crashes in the case of udp and tcp, but I've seen this set to too
small values which triggered awful performance. It also makes the
setting consistent across all the wmem/rmem sysctls.
Signed-off-by: Sorin Dumitru <sdumitru@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Furthermore there is devm_gpiod_get_optional which is designed to get
optional gpios.
Simplify driver accordingly.
Note this makes error checking more strict because only -ENOENT is
ignored when searching for the GPIOs which is good.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was possible for mac80211 to be coerced into an
unexpected flow causing sdata union to become
corrupted. Station pointer was put into
sdata->u.vlan.sta memory location while it was
really master AP's sdata->u.ap.next_beacon. This
led to station entry being later freed as
next_beacon before __sta_info_flush() in
ieee80211_stop_ap() and a subsequent invalid
pointer dereference crash.
The problem was that ieee80211_ptr->use_4addr
wasn't cleared on interface type changes.
This could be reproduced with the following steps:
# host A and host B have just booted; no
# wpa_s/hostapd running; all vifs are down
host A> iw wlan0 set type station
host A> iw wlan0 set 4addr on
host A> printf 'interface=wlan0\nssid=4addrcrash\nchannel=1\nwds_sta=1' > /tmp/hconf
host A> hostapd -B /tmp/conf
host B> iw wlan0 set 4addr on
host B> ifconfig wlan0 up
host B> iw wlan0 connect -w hostAssid
host A> pkill hostapd
# host A crashed:
[ 127.928192] BUG: unable to handle kernel NULL pointer dereference at 00000000000006c8
[ 127.929014] IP: [<ffffffff816f4f32>] __sta_info_flush+0xac/0x158
...
[ 127.934578] [<ffffffff8170789e>] ieee80211_stop_ap+0x139/0x26c
[ 127.934578] [<ffffffff8100498f>] ? dump_trace+0x279/0x28a
[ 127.934578] [<ffffffff816dc661>] __cfg80211_stop_ap+0x84/0x191
[ 127.934578] [<ffffffff816dc7ad>] cfg80211_stop_ap+0x3f/0x58
[ 127.934578] [<ffffffff816c5ad6>] nl80211_stop_ap+0x1b/0x1d
[ 127.934578] [<ffffffff815e53f8>] genl_family_rcv_msg+0x259/0x2b5
Note: This isn't a revert of f8cdddb8d6
("cfg80211: check iface combinations only when
iface is running") as far as functionality is
considered because b6a550156b ("cfg80211/mac80211:
move more combination checks to mac80211") moved
the logic somewhere else already.
Fixes: f8cdddb8d6 ("cfg80211: check iface combinations only when iface is running")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There was a possible race between
ieee80211_reconfig() and
ieee80211_delayed_tailroom_dec(). This could
result in inability to transmit data if driver
crashed during roaming or rekeying and subsequent
skbs with insufficient tailroom appeared.
This race was probably never seen in the wild
because a device driver would have to crash AND
recover within 0.5s which is very unlikely.
I was able to prove this race exists after
changing the delay to 10s locally and crashing
ath10k via debugfs immediately after GTK
rekeying. In case of ath10k the counter went below
0. This was harmless but other drivers which
actually require tailroom (e.g. for WEP ICV or
MMIC) could end up with the counter at 0 instead
of >0 and introduce insufficient skb tailroom
failures because mac80211 would not resize skbs
appropriately anymore.
Fixes: 8d1f7ecd2a ("mac80211: defer tailroom counter manipulation when roaming")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove these unnecessary brackets inside a condition.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This patch tries to increase code readability by negating the first if
block and rearranging some of the other conditional blocks. This way we
save an indentation level, we also save some allocation that is not
necessary for one of the conditions.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The current default settings for optional features in batman-adv seems to
be based around the idea that the user only compiles what he requires. They
will automatically enabled when they are compiled in. For example the
network coding part of batman-adv is by default disabled in the out-of-tree
module but will be enabled when the code is compiled during the module
build.
But distributions like Debian just enable all features of the batman-adv
kernel module and hope that more experimental features or features with
possible negative effects have to be enabled using some runtime
configuration interface.
The network_coding feature can help in specific setups but also has
drawbacks and is not disabled by default in the out-of-tree module.
Disabling by default in the runtime config seems to be also quite sane.
The bridge_loop_avoidance is the only feature which is disabled by default
but may be necessary even in simple setups. Packet loops may even be
created during the initial node setup when this is not enabled. This is
different than STP on bridges because mesh is usually used on Adhoc WiFi.
Having two nodes (by accident) in the same LAN segment and in the same mesh
network is rather common in this situation.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This string pointer is later assigned to a constant string, so it should
be defined constant at the beginning.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This function returns bool values, so it should be defined to return
them instead of the whole int range.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Directly return error values. No need to use a return variable.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The whole Makefile is sorted, just the multicast rule is not at the
right position.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Instead of hiding the normal function flow inside an if block, we should
just put the error handling into the if block.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Normally the debugfs framework will return error pointer with -ENODEV
for function calls when DEBUG_FS is not set.
batman does not notice this error code and continues trying to create
debugfs files and executes more code. We can avoid this code execution
by disabling compiling debugfs.c when DEBUG_FS is not set.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The fragment queueing code now validates the total_size of each fragment,
checks when enough fragments are queued to allow to merge them into a
single packet and if the fragments have the correct size. Therefore, it is
not required to have any other parameter for the merging function than a
list of queued fragments.
This change should avoid problems like in the past when the different skb
from the list and the function parameter were mixed incorrectly.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The fragmentation code was replaced in
610bfc6bc9 ("batman-adv: Receive fragmented
packets and merge") by an implementation which handles the queueing+merging
of fragments based on their size and the total_size of the non-fragmented
packet. This total_size is announced by each fragment. The new
implementation doesn't check if the the total_size information of the
packets inside one chain is consistent.
This is consistency check is recommended to allow using any of the packets
in the queue to decide whether all fragments of a packet are received or
not.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Steffen Klassert says:
====================
pull request (net): ipsec 2015-05-28
1) Fix a race in xfrm_state_lookup_byspi, we need to take
the refcount before we release xfrm_state_lock.
From Li RongQing.
2) Fix IV generation on ESN state. We used just the
low order sequence numbers for IV generation on
ESN, as a result the IV can repeat on the same
state. Fix this by using the high order sequence
number bits too and make sure to always initialize
the high order bits with zero. These patches are
serious stable candidates. Fixes from Herbert Xu.
3) Fix the skb->mark handling on vti. We don't
reset skb->mark in skb_scrub_packet anymore,
so vti must care to restore the original
value back after it was used to lookup the
vti policy and state. Fixes from Alexander Duyck.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2015-05-28
1) Remove xfrm_queue_purge as this is the same as skb_queue_purge.
2) Optimize policy and state walk.
3) Use a sane return code if afinfo registration fails.
4) Only check fori a acquire state if the state is not valid.
5) Remove a unnecessary NULL check before xfrm_pol_hold
as it checks the input for NULL.
6) Return directly if the xfrm hold queue is empty, avoid
to take a lock as it is nothing to do in this case.
7) Optimize the inexact policy search and allow for matching
of policies with priority ~0U.
All from Li RongQing.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The vti6_rcv_cb and vti_rcv_cb calls were leaving the skb->mark modified
after completing the function. This resulted in the original skb->mark
value being lost. Since we only need skb->mark to be set for
xfrm_policy_check we can pull the assignment into the rcv_cb calls and then
just restore the original mark after xfrm_policy_check has been completed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This change makes it so that if a tunnel is defined we just use the mark
from the tunnel instead of the mark from the skb header. By doing this we
can avoid the need to set skb->mark inside of the tunnel receive functions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Instead of modifying skb->mark we can simply modify the flowi_mark that is
generated as a result of the xfrm_decode_session. By doing this we don't
need to actually touch the skb->mark and it can be preserved as it passes
out through the tunnel.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch makes use of the new AEAD interface which uses a single
SG list instead of separate lists for the AD and plain text.
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch makes use of the new AEAD interface which uses a single
SG list instead of separate lists for the AD and plain text.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch makes use of the new AEAD interface which uses a single
SG list instead of separate lists for the AD and plain text. The
IV generation is also now carried out through normal AEAD methods.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch makes use of the new AEAD interface which uses a single
SG list instead of separate lists for the AD and plain text. The
IV generation is also now carried out through normal AEAD methods.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds IV generator information to xfrm_state. This
is currently obtained from our own list of algorithm descriptions.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds IV generator information for each AEAD and block
cipher to xfrm_algo_desc. This will be used to access the new
AEAD interface.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull networking fixes from David Miller:
1) Don't use MMIO on certain iwlwifi devices otherwise we get a
firmware crash.
2) Don't corrupt the GRO lists of mac80211 contexts by doing sends via
timer interrupt, from Johannes Berg.
3) SKB tailroom is miscalculated in AP_VLAN crypto code, from Michal
Kazior.
4) Fix fw_status memory leak in iwlwifi, from Haim Dreyfuss.
5) Fix use after free in iwl_mvm_d0i3_enable_tx(), from Eliad Peller.
6) JIT'ing of large BPF programs is broken on x86, from Alexei
Starovoitov.
7) EMAC driver ethtool register dump size is miscalculated, from Ivan
Mikhaylov.
8) Fix PHY initial link mode when autonegotiation is disabled in
amd-xgbe, from Tom Lendacky.
9) Fix NULL deref on SOCK_DEAD socket in AF_UNIX and CAIF protocols,
from Mark Salyzyn.
10) credit_bytes not initialized properly in xen-netback, from Ross
Lagerwall.
11) Fallback from MSI-X to INTx interrupts not handled properly in mlx4
driver, fix from Benjamin Poirier.
12) Perform ->attach() after binding dev->qdisc in packet scheduler,
otherwise we can crash. From Cong WANG.
13) Don't clobber data in sctp_v4_map_v6(). From Jason Gunthorpe.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (30 commits)
sctp: Fix mangled IPv4 addresses on a IPv6 listening socket
net_sched: invoke ->attach() after setting dev->qdisc
xen-netfront: properly destroy queues when removing device
mlx4_core: Fix fallback from MSI-X to INTx
xen/netback: Properly initialize credit_bytes
net: netxen: correct sysfs bin attribute return code
tools: bpf_jit_disasm: fix segfault on disabled debugging log output
unix/caif: sk_socket can disappear when state is unlocked
amd-xgbe-phy: Fix initial mode when autoneg is disabled
net: dp83640: fix improper double spin locking.
net: dp83640: reinforce locking rules.
net: dp83640: fix broken calibration routine.
net: stmmac: create one debugfs dir per net-device
net/ibm/emac: fix size of emac dump memory areas
x86: bpf_jit: fix compilation of large bpf programs
net: phy: bcm7xxx: Fix 7425 PHY ID and flags
iwlwifi: mvm: avoid use-after-free on iwl_mvm_d0i3_enable_tx()
iwlwifi: mvm: clean net-detect info if device was reset during suspend
iwlwifi: mvm: take the UCODE_DOWN reference when resuming
iwlwifi: mvm: BT Coex - duplicate the command if sent ASYNC
...
After commit 07f4c90062 ("tcp/dccp: try to not exhaust
ip_local_port_range in connect()") it is advised to have an even number
of ports described in /proc/sys/net/ipv4/ip_local_port_range
This means start/end values should have a different parity.
Let's warn sysadmins of this, so that they can update their settings
if they want to.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__inet_hash_connect() does not use its third argument (port_offset)
if socket was already bound to a source port.
No need to perform useless but expensive md5 computations.
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For mq qdisc, we add per tx queue qdisc to root qdisc
for display purpose, however, that happens too early,
before the new dev->qdisc is finally set, this causes
q->list points to an old root qdisc which is going to be
freed right before assigning with a new one.
Fix this by moving ->attach() after setting dev->qdisc.
For the record, this fixes the following crash:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 975 at lib/list_debug.c:59 __list_del_entry+0x5a/0x98()
list_del corruption. prev->next should be ffff8800d1998ae8, but was 6b6b6b6b6b6b6b6b
CPU: 1 PID: 975 Comm: tc Not tainted 4.1.0-rc4+ #1019
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
0000000000000009 ffff8800d73fb928 ffffffff81a44e7f 0000000047574756
ffff8800d73fb978 ffff8800d73fb968 ffffffff810790da ffff8800cfc4cd20
ffffffff814e725b ffff8800d1998ae8 ffffffff82381250 0000000000000000
Call Trace:
[<ffffffff81a44e7f>] dump_stack+0x4c/0x65
[<ffffffff810790da>] warn_slowpath_common+0x9c/0xb6
[<ffffffff814e725b>] ? __list_del_entry+0x5a/0x98
[<ffffffff81079162>] warn_slowpath_fmt+0x46/0x48
[<ffffffff81820eb0>] ? dev_graft_qdisc+0x5e/0x6a
[<ffffffff814e725b>] __list_del_entry+0x5a/0x98
[<ffffffff814e72a7>] list_del+0xe/0x2d
[<ffffffff81822f05>] qdisc_list_del+0x1e/0x20
[<ffffffff81820cd1>] qdisc_destroy+0x30/0xd6
[<ffffffff81822676>] qdisc_graft+0x11d/0x243
[<ffffffff818233c1>] tc_get_qdisc+0x1a6/0x1d4
[<ffffffff810b5eaf>] ? mark_lock+0x2e/0x226
[<ffffffff817ff8f5>] rtnetlink_rcv_msg+0x181/0x194
[<ffffffff817ff72e>] ? rtnl_lock+0x17/0x19
[<ffffffff817ff72e>] ? rtnl_lock+0x17/0x19
[<ffffffff817ff774>] ? __rtnl_unlock+0x17/0x17
[<ffffffff81855dc6>] netlink_rcv_skb+0x4d/0x93
[<ffffffff817ff756>] rtnetlink_rcv+0x26/0x2d
[<ffffffff818544b2>] netlink_unicast+0xcb/0x150
[<ffffffff81161db9>] ? might_fault+0x59/0xa9
[<ffffffff81854f78>] netlink_sendmsg+0x4fa/0x51c
[<ffffffff817d6e09>] sock_sendmsg_nosec+0x12/0x1d
[<ffffffff817d8967>] sock_sendmsg+0x29/0x2e
[<ffffffff817d8cf3>] ___sys_sendmsg+0x1b4/0x23a
[<ffffffff8100a1b8>] ? native_sched_clock+0x35/0x37
[<ffffffff810a1d83>] ? sched_clock_local+0x12/0x72
[<ffffffff810a1fd4>] ? sched_clock_cpu+0x9e/0xb7
[<ffffffff810def2a>] ? current_kernel_time+0xe/0x32
[<ffffffff810b4bc5>] ? lock_release_holdtime.part.29+0x71/0x7f
[<ffffffff810ddebf>] ? read_seqcount_begin.constprop.27+0x5f/0x76
[<ffffffff810b6292>] ? trace_hardirqs_on_caller+0x17d/0x199
[<ffffffff811b14d5>] ? __fget_light+0x50/0x78
[<ffffffff817d9808>] __sys_sendmsg+0x42/0x60
[<ffffffff817d9838>] SyS_sendmsg+0x12/0x1c
[<ffffffff81a50e97>] system_call_fastpath+0x12/0x6f
---[ end trace ef29d3fb28e97ae7 ]---
For long term, we probably need to clean up the qdisc_graft() code
in case it hides other bugs like this.
Fixes: 95dc19299f ("pkt_sched: give visibility to mq slave qdiscs")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A long standing problem on busy servers is the tiny available TCP port
range (/proc/sys/net/ipv4/ip_local_port_range) and the default
sequential allocation of source ports in connect() system call.
If a host is having a lot of active TCP sessions, chances are
very high that all ports are in use by at least one flow,
and subsequent bind(0) attempts fail, or have to scan a big portion of
space to find a slot.
In this patch, I changed the starting point in __inet_hash_connect()
so that we try to favor even [1] ports, leaving odd ports for bind()
users.
We still perform a sequential search, so there is no guarantee, but
if connect() targets are very different, end result is we leave
more ports available to bind(), and we spread them all over the range,
lowering time for both connect() and bind() to find a slot.
This strategy only works well if /proc/sys/net/ipv4/ip_local_port_range
is even, ie if start/end values have different parity.
Therefore, default /proc/sys/net/ipv4/ip_local_port_range was changed to
32768 - 60999 (instead of 32768 - 61000)
There is no change on security aspects here, only some poor hashing
schemes could be eventually impacted by this change.
[1] : The odd/even property depends on ip_local_port_range values parity
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for setting the current cca ed level value over
nl802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds information about the current cca ed level when the phy
is dumped over nl802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We currently always send fragments without DF bit set.
Thus, given following setup:
mtu1500 - mtu1500:1400 - mtu1400:1280 - mtu1280
A R1 R2 B
Where R1 and R2 run linux with netfilter defragmentation/conntrack
enabled, then if Host A sent a fragmented packet _with_ DF set to B, R1
will respond with icmp too big error if one of these fragments exceeded
1400 bytes.
However, if R1 receives fragment sizes 1200 and 100, it would
forward the reassembled packet without refragmenting, i.e.
R2 will send an icmp error in response to a packet that was never sent,
citing mtu that the original sender never exceeded.
The other minor issue is that a refragmentation on R1 will conceal the
MTU of R2-B since refragmentation does not set DF bit on the fragments.
This modifies ip_fragment so that we track largest fragment size seen
both for DF and non-DF packets, and set frag_max_size to the largest
value.
If the DF fragment size is larger or equal to the non-df one, we will
consider the packet a path mtu probe:
We set DF bit on the reassembled skb and also tag it with a new IPCB flag
to force refragmentation even if skb fits outdev mtu.
We will also set DF bit on each fragment in this case.
Joint work with Hannes Frederic Sowa.
Reported-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_skb_dst_mtu is small inline helper, but its called in several places.
before: 17061 44 0 17105 42d1 net/ipv4/ip_output.o
after: 16805 44 0 16849 41d1 net/ipv4/ip_output.o
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds transmission power setting support for IEEE-802.15.4
devices via nl802154.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We used to get this indirectly I supposed, but no longer do.
Either way, an explicit include should have been done in the
first place.
net/ipv4/fib_trie.c: In function '__node_free_rcu':
>> net/ipv4/fib_trie.c:293:3: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
vfree(n);
^
net/ipv4/fib_trie.c: In function 'tnode_alloc':
>> net/ipv4/fib_trie.c:312:3: error: implicit declaration of function 'vzalloc' [-Werror=implicit-function-declaration]
return vzalloc(size);
^
>> net/ipv4/fib_trie.c:312:3: warning: return makes pointer from integer without a cast
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By making sure sk->sk_gso_max_segs minimal value is one,
and sysctl_tcp_min_tso_segs minimal value is one as well,
tcp_tso_autosize() will return a non zero value.
We can then revert 843925f33f
("tcp: Do not apply TSO segment limit to non-TSO packets")
and save few cpu cycles in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
got a rare NULL pointer dereference in clear_bit
Signed-off-by: Mark Salyzyn <salyzyn@android.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
----
v2: switch to sock_flag(sk, SOCK_DEAD) and added net/caif/caif_socket.c
v3: return -ECONNRESET in upstream caller of wait function for SOCK_DEAD
Signed-off-by: David S. Miller <davem@davemloft.net>
If tcp ehash table is constrained to a very small number of buckets
(eg boot parameter thash_entries=128), then we can crash if spinlock
array has more entries.
While we are at it, un-inline inet_ehash_locks_alloc() and make
following changes :
- Budget 2 cache lines per cpu worth of 'spinlocks'
- Try to kmalloc() the array to avoid extra TLB pressure.
(Most servers at Google allocate 8192 bytes for this hash table)
- Get rid of various #ifdef
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit dd3f9e70f5
("tipc: add packet sequence number at instant of transmission") we
made a change with the consequence that packets in the link backlog
queue don't contain valid sequence numbers.
However, when we create a link protocol message, we still use the
sequence number of the first packet in the backlog, if there is any,
as "next_sent" indicator in the message. This may entail unnecessary
retransissions or stale packet transmission when there is very low
traffic on the link.
This commit fixes this issue by only using the current value of
tipc_link::snd_nxt as indicator.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* AP_VLAN tailroom calculation fix, the bug leads to warnings
along with dropped packets
* NAPI context issue, calling napi_gro_receive() from a timer
(obviously) can lead to crashes
* remain-on-channel combining leads to dropped requests and not
being able to finish certain operations, so remove it
-----BEGIN PGP SIGNATURE-----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=PS0g
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2015-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
We have three more fixes:
* AP_VLAN tailroom calculation fix, the bug leads to warnings
along with dropped packets
* NAPI context issue, calling napi_gro_receive() from a timer
(obviously) can lead to crashes
* remain-on-channel combining leads to dropped requests and not
being able to finish certain operations, so remove it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the handling to call cca mode setting. If the phy isn't
flag then the driver doesn't support this setting.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
mac802154_mlme_start_req() calls
ieee802154_mlme_ops(dev)->llsec->set_params() on the net_device
passed into it, however, this net_device will always be a mac802154
net_device, so just call mac802154_set_params() directly instead.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
ieee802154_get_dev() only returns devices that have dev->type ==
ARPHRD_IEEE802154, therefore, there is no need to check this again
in raw_bind().
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In the past, 802.15.4 interfaces and 6LoWPAN interfaces used the
same dev->type (ARPHRD_IEEE802154), and 802.15.4 interfaces were
distinguished from 6LoWPAN interfaces by their differing dev->mtu.
6LoWPAN interfaces have their own ARPHRD type now, so there is no
longer any need to check dev->mtu to distinguish 802.15.4 devices
from 6LoWPAN devices.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This allows us to create netdev tables that contain ingress chains. Use
skb_header_pointer() as we may see shared sk_buffs at this stage.
This change provides access to the existing nf_tables features from the ingress
hook.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds the internal NFT_AF_NEEDS_DEV flag to indicate that you must
attach this table to a net_device.
This change is required by the follow up patch that introduces the new netdev
table.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Eric Dumazet