Add missing kernel-doc notation in scsi_transport_fc.c:
Warning(drivers/scsi/scsi_transport_fc.c:3593): No description found for parameter 'q'
Warning(drivers/scsi/scsi_transport_fc.c:3700): No description found for parameter 'q'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add support for 32-byte READ/WRITE as well as DIF Type 2 protection.
Reject protected 10/12/16 byte READ/WRITE commands when Type 2 is
enabled.
Verify Type 2 reference tag according to Expected Initial LBA in 32-byte
CDB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Disks formatted with DIF Type 2 reject READ/WRITE 6/10/12/16 commands
when protection is enabled. Only the 32-byte variants are supported.
Implement support for issusing 32-byte READ/WRITE and enable Type 2
drives in the protection type detection logic.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We would leak a scsi_data_buffer if the free_list command was of the
protected variety.
Reported-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
So far we have only issued DIF commands if CONFIG_BLK_DEV_INTEGRITY is
enabled. However, communication between initiator and target should be
independent of protection information DMA. There are DIF-only host
adapters coming out that will be able to take advantage of this.
Move the relevant DIF bits to sd.c.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The checksum format is orthogonal to whether the protection information
is being passed on beyond the HBA or not. It is perfectly valid to use
a non-T10 CRC with WRITE_STRIP and READ_INSERT.
Consequently it no longer makes sense to explicitly refer to the
conversion in the protection operation. Update sd_dif and lpfc
accordingly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Ihab Hamadi <Ihab.Hamadi@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
A target reset when I/O is ongoing might result
an eventual device offline, as scsi_eh_completed_normally()
might return ADD_TO_MLQUEUE in addition to the
advertised SUCCESS, FAILED, and NEEDS_RETRY.
Which is unfortunate as scsi_send_eh_cmnd() will
therefore map ADD_TO_MLQUEUE to FAILED instead of
the more appropriate NEEDS_RETRY.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Running sg_luns on s390x with CONFIG_DEBUG_PAGEALLOC enabled fails
with EFAULT from the SG_IO ioctl. The EFAULT is the result from
copy_to_user failing in this call chain:
sg_ioctl
sg_new_read
sg_finish_rem_req
blk_rq_unmap_user
__blk_rq_unmap_user
bio_uncopy_user
__bio_copy_iov
copy_to_user
The sg driver calls sg_remove_scat to free the memory pages before
calling blk_rq_unmap_user that tries to copy the data back to
userspace. Change the order to first call blk_rq_unmap_user before
freeing the pages in sg_remove_scat.
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: stable@kernel.org
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
On certain cases, UDF disc doesn't report capacity correctly via
READ_CAPACITY but TOC or trackinfo contains valid information which
can be obtained using cdrom_get_last_written(). ide-cd considers both
values and uses the larger one. Do the same in sr. This fixes
bko#9668.
http://bugzilla.kernel.org/show_bug.cgi?id=9668
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Milan Kocian <milan.kocian@wq.cz>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
5706/5708/5709 devices allow driver/user to set page size. By default it is
set to 4096. Current drivers do not program this register based on
architecture type (e.g. x86 = 4K, IA64 = 16K) and by choice lets device use
the defaults. So while mapping connection context memory (doorebll registers),
driver has to match page size used by the device. Included change fixes the
issue we uncovered during IA64 testing
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Most code changes were made to support RR44xx adapters.
- add more PCI device ID.
- using PCI BAR[2] to access RR44xx IOP.
- using PCI BAR[0] to check and clear RR44xx IRQ.
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The function mode_select_handle_sense returns SCSI_DH_OK even when there is a sense code which is incorrect. Removing it so that it returns SCSI_DH_IO when there is sense that is not handled by this function.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Reviewed-by: Vijay Chauhan <vijay.chauhan@lsi.com>
Reviewed-by: Bob Stankey <Robert.stankey@lsi.com>
Reviewed-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1.Changed driver prints to use scmd_printk, sdev_printk
2.Changed dev_err calls to scmd_printk for scsi related print messages
Signed-off-by: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is support for Areca SAS/SATA HBA, ARC-1300/1320, which quipped with
88SE6440/88SE9480 respectively.
Signed-off-by: Nick Cheng< nick.cheng@areca.com.tw >
Cc: Ke Wei <kewei.mv@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / yenta: Fix cardbus suspend/resume regression
PM / PCMCIA: Drop second argument of pcmcia_socket_dev_suspend()
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
sony-laptop: re-read the rfkill state when resuming from suspend
sony-laptop: check for rfkill hard block at load time
wext: add back wireless/ dir in sysfs for cfg80211 interfaces
wext: Add bound checks for copy_from_user
mac80211: improve/fix mlme messages
cfg80211: always get BSS
iwlwifi: fix 3945 ucode info retrieval after failure
iwlwifi: fix memory leak in command queue handling
iwlwifi: fix debugfs buffer handling
cfg80211: don't set privacy w/o key
cfg80211: wext: don't display BSSID unless associated
net: Add explicit bound checks in net/socket.c
bridge: Fix double-free in br_add_if.
isdn: fix netjet/isdnhdlc build errors
atm: dereference of he_dev->rbps_virt in he_init_group()
ax25: Add missing dev_put in ax25_setsockopt
Revert "sit: stateless autoconf for isatap"
net: fix double skb free in dcbnl
net: fix nlmsg len size for skb when error bit is set.
net: fix vlan_get_size to include vlan_flags size
...
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (25 commits)
drm/radeon/kms: Convert R520 to new init path and associated cleanup
drm/radeon/kms: Convert RV515 to new init path and associated cleanup
drm: fix radeon DRM warnings when !CONFIG_DEBUG_FS
drm: fix drm_fb_helper warning when !CONFIG_MAGIC_SYSRQ
drm/r600: fix memory leak introduced with 64k malloc avoidance fix.
drm/kms: make fb helper work for all drivers.
drm/radeon/r600: fix offset handling in CS parser
drm/radeon/kms/r600: fix forcing pci mode on agp cards
drm/radeon/kms: fix for the extra pages copying.
drm/radeon/kms/r600: add support for vline relocs
drm/radeon/kms: fix some bugs in vline reloc
drm/radeon/kms/r600: clamp vram to aperture size
drm/kms: protect against fb helper not being created.
drm/r600: get values from the passed in IB not the copy.
drm: create gitignore file for radeon
drm/radeon/kms: remove unneeded master create/destroy functions.
drm/kms: start adding command line interface using fb.
fb: change rules for global rules match.
drm/radeon/kms: don't require up to 64k allocations. (v2)
drm/radeon/kms: enable dac load detection by default.
...
Trivial conflicts in drivers/gpu/drm/radeon/radeon_asic.h due to adding
'->vga_set_state' function pointers.
David Howells noticed (due to the compiler warning about an unused
'pty_ops_bsd' variable) that we haven't actually been using the code
that implements TIOCSPTLCK for legacy pty handling. It's been that way
since 2.6.26, commit 3e8e88ca05 to be
exact ("pty: prepare for tty->ops changes").
DavidH initially submitted a patch just removing the dead code entirely,
and since nobody has apparently ever complained, I'm not entirely sure
that wouldn't be the right thing to do. But since the whole and only
point of the legacy pty code is to be compatible with legacy distros
that don't use the new unix98 pty model, let's just wire it up again.
And clean it up a bit while we're at it.
Acked-by: David Howells <dhowells@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the r520 asic support to new init path, change are smaller than
previous one as most of the architecture is now in place and more code
sharing can happen btw various asics.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Convert the rv515 asic support to new init path also add an explanation
in radeon.h about the new init path. There is also few cleanups
associated with this change (others asic calling rv515 helper
functions).
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Compiling the radeon DRM driver with !CONFIG_DEBUG_FS
throws the following warnings:
drivers/gpu/drm/radeon/radeon_ttm.c: In function 'radeon_ttm_debugfs_init':
drivers/gpu/drm/radeon/radeon_ttm.c:714: warning: unused variable 'i'
drivers/gpu/drm/radeon/radeon_ttm.c: At top level:
drivers/gpu/drm/radeon/radeon_ttm.c:692: warning: 'radeon_mem_types_list' defined but not used
drivers/gpu/drm/radeon/radeon_ttm.c:693: warning: 'radeon_mem_types_names' defined but not used
Fix: move these variables inside the #if defined(CONFIG_DEBUG_FS)
block in radeon_ttm_debugsfs_init(), which is the only place using them.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Compiling DRM throws the following warning if MAGIC_SYSRQ is disabled:
drivers/gpu/drm/drm_fb_helper.c:101: warning: 'sysrq_drm_fb_helper_restore_op' defined but not used
Fix: place sysrq_drm_fb_helper_restore_op and associated
definitions inside #ifdef CONFIG_MAGIC_SYSRQ.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Since 2.6.29 the PCI PM core have been restoring the standard
configuration registers of PCI devices in the early phase of
resume. In particular, PCI devices without drivers have been handled
this way since commit 355a72d75b
(PCI: Rework default handling of suspend and resume). Unfortunately,
this leads to post-resume problems with CardBus devices which cannot
be accessed in the early phase of resume, because the sockets they
are on have not been woken up yet at that point.
To solve this problem, move the yenta socket resume to the early
phase of resume and, analogously, move the suspend of it to the late
phase of suspend. Additionally, remove some unnecessary PCI code
from the yenta socket's resume routine.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13092, which is a
post-2.6.28 regression.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Florian <fs-kernelbugzilla@spline.de>
Cc: stable@kernel.org
pcmcia_socket_dev_suspend() doesn't use its second argument, so it
may be dropped safely.
This change is necessary for the subsequent yenta suspend/resume fix.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
Without this, the hard-blocked state will be reported incorrectly if
the hardware switch is changed while the laptop is suspended.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Tested-by: Norbert Preining <preining@logic.at>
Acked-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"I recently (on a flight) I found out that when I boot with the hard-switch
activated, so turning off all wireless activity on my laptop, the state
is not correctly announced in /dev/rfkill (reading it with rfkill command,
or my own gnome applet)...
After turning off and on again the hard-switch the events were right."
We can fix this by querying the firmware at load time and calling
rfkill_set_hw_state().
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Tested-by: Norbert Preining <preining@logic.at>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Mattia Dongili <malattia@linux.it>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hardware or uCode problem occurs driver captures significant
information from device to enable debugging. The format of this information
is different between 3945 and 4965 and later devices, yet currently the
3945 uses the 4965 and later format. Fix this by adding a new library call
that is initialized to the correct formatting routine based on device.
This moves the iwlagn event and error log handling back to iwl-agn.c to
make it part of iwlagn module.
Also remove the 3945 sysfs file that triggers dump of event log - there is
already a debugfs file that can do it for all drivers.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also free the array of command pointers and meta data of each
command buffer when command queue is freed.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We keep track of where to write into a buffer by keeping a count of how
much has been written so far. When writing to the buffer we thus take the
buffer pointer and adding the count of what has been written so far.
Keeping track of what has been written so far is done by incrementing
this number every time something is written to the buffer with how much has
been written at that time.
Currently this number is incremented incorrectly when using the
"hex_dump_to_buffer" call to add data to the buffer. Fix this by only
adding what has been added to the buffer in that call instead of what has
been added since beginning of buffer.
Issue was discovered and discussed during testing of
https://bugzilla.redhat.com/show_bug.cgi?id=464598 .
When a user views any of these files they will see something like:
[ 179.355202] ------------[ cut here ]------------
[ 179.355209] WARNING: at ../lib/vsprintf.c:989 vsnprintf+0x5ec/0x5f0()
[ 179.355212] Hardware name: VGN-Z540N
[ 179.355213] Modules linked in: i915 drm i2c_algo_bit i2c_core ipv6 acpi_cpufreq cpufreq_userspace cpufreq_powersave cpufreq_ondemand cpufreq_conservative cpufreq_stats freq_table container sbs sbshc arc4 ecb iwlagn iwlcore joydev led_class mac80211 af_packet pcmcia psmouse sony_laptop cfg80211 iTCO_wdt iTCO_vendor_support pcspkr serio_raw rfkill intel_agp video output tpm_infineon tpm tpm_bios button battery yenta_socket rsrc_nonstatic pcmcia_core processor ac evdev ext3 jbd mbcache sr_mod sg cdrom sd_mod ahci libata scsi_mod ehci_hcd uhci_hcd usbcore thermal fan thermal_sys
[ 179.355262] Pid: 5449, comm: cat Not tainted 2.6.31-wl-54419-ge881071 #62
[ 179.355264] Call Trace:
[ 179.355267] [<ffffffff811ad14c>] ? vsnprintf+0x5ec/0x5f0
[ 179.355271] [<ffffffff81041348>] warn_slowpath_common+0x78/0xd0
[ 179.355275] [<ffffffff810413af>] warn_slowpath_null+0xf/0x20
[ 179.355277] [<ffffffff811ad14c>] vsnprintf+0x5ec/0x5f0
[ 179.355280] [<ffffffff811ad23d>] ? scnprintf+0x5d/0x80
[ 179.355283] [<ffffffff811ad23d>] scnprintf+0x5d/0x80
[ 179.355286] [<ffffffff811aed29>] ? hex_dump_to_buffer+0x189/0x340
[ 179.355290] [<ffffffff810e91d7>] ? __kmalloc+0x207/0x260
[ 179.355303] [<ffffffffa02a02f8>] iwl_dbgfs_nvm_read+0xe8/0x220 [iwlcore]
[ 179.355306] [<ffffffff811a9b62>] ? __up_read+0x92/0xb0
[ 179.355310] [<ffffffff810f0988>] vfs_read+0xc8/0x1a0
[ 179.355313] [<ffffffff810f0b50>] sys_read+0x50/0x90
[ 179.355316] [<ffffffff8100bd6b>] system_call_fastpath+0x16/0x1b
[ 179.355319] ---[ end trace 2383d0d5e0752ca0 ]---
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit cb3824bade didn't fix this problem.
Fix build errors in netjet, using isdnhdlc module:
drivers/built-in.o: In function `mode_tiger':
netjet.c:(.text+0x1ca0c7): undefined reference to `isdnhdlc_rcv_init'
netjet.c:(.text+0x1ca0d4): undefined reference to `isdnhdlc_out_init'
drivers/built-in.o: In function `fill_dma':
netjet.c:(.text+0x1ca2bd): undefined reference to `isdnhdlc_encode'
drivers/built-in.o: In function `read_dma':
netjet.c:(.text+0x1ca614): undefined reference to `isdnhdlc_decode'
drivers/built-in.o: In function `nj_irq':
netjet.c:(.text+0x1cb07a): undefined reference to `isdnhdlc_encode'
drivers/built-in.o: In function `isdnhdlc_decode':
(.text+0x1c2088): undefined reference to `crc_ccitt_table'
drivers/built-in.o: In function `isdnhdlc_encode':
(.text+0x1c2339): undefined reference to `crc_ccitt_table'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prefix decrement causes a very long loop if pci_pool_alloc() failed
in the first iteration. Also I swapped rbps and rbpl arguments.
Reported-by: Juha Leppanen <juha_motorsportcom@luukku.com>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The legacy r600 path shares code, but doesn't share quite enough
to get the freeing correct. Free the pages here also.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This initialises the fb helper with the connector helper,
so that the fb cmdline code works for intel as well.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The following commit made console open fails while booting:
commit b50989dc44
Author: Alan Cox <alan@linux.intel.com>
Date: Sat Sep 19 13:13:22 2009 -0700
tty: make the kref destructor occur asynchronously
Due to tty release routines run in a workqueue now, error like the
following will be reported while booting:
INIT open /dev/console Input/output error
It also causes hibernation regression to appear as reported at
http://bugzilla.kernel.org/show_bug.cgi?id=14229
The reason is that now there's latency issue with closing, but when
we open a "closing not finished" tty, -EIO will be returned.
Fix it as per the following Alan's suggestion:
Fun but it's actually not a bug and the fix is wrong in itself as
the port may be closing but not yet being destructed, in which case
it seems to do the wrong thing. Opening a tty that is closing (and
could be closing for long periods) is supposed to return -EIO.
I suspect a better way to deal with this and keep the old console
timing is to split tty->shutdown into two functions.
tty->shutdown() - called synchronously just before we dump the tty
onto the waitqueue for destruction
tty->cleanup() - called when the destructor runs.
We would then do the shutdown part which can occur in IRQ context
fine, before queueing the rest of the release (from tty->magic = 0
... the end) to occur asynchronously
The USB update in -next would then need a call like
if (tty->cleanup)
tty->cleanup(tty);
at the top of the async function and the USB shutdown to be split
between shutdown and cleanup as the USB resource cleanup and final
tidy cannot occur synchronously as it needs to sleep.
In other words the logic becomes
final kref put
make object unfindable
async
clean it up
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
[ rjw: Rebased on top of 2.6.31-git, reworked the changelog. ]
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
[ Changed serial naming to match new rules, dropped tty_shutdown as per
comments from Alan Stern - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 3d5b6fb47a ("ACPI: Kill overly
verbose "power state" log messages") removed the actual use of this
variable, but didn't remove the variable itself, resulting in build
warnings like
drivers/acpi/processor_idle.c: In function ‘acpi_processor_power_init’:
drivers/acpi/processor_idle.c:1169: warning: unused variable ‘i’
Just get rid of the now unused variable.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code
But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I was recently lucky enough to get a 64-CPU system, so my kernel log
ends up with 64 lines like:
ACPI: CPU0 (power states: C1[C1] C2[C3])
This is pretty useless clutter because this info is already available
after boot from both /sys/devices/system/cpu/cpu*/cpuidle/state?/ as
well as /proc/acpi/processor/CPU*/power.
So just delete the code that prints the C-states in processor_idle.c.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The message "ACPI: Device needs an ACPI driver" is misleading. The
device _may_ need an ACPI driver, if the BIOS implemented a custom
API for the device in question (which, AFAIK, can't be checked.) If
not, then either a generic ACPI driver may be used (for example
"thermal"), or nothing can be done (other than a white list).
I propose to reword the message to:
ACPI: If an ACPI driver is available for this device, you should use
it instead of the native driver
which I think is more correct. Comments and suggestions welcome.
I also added a message warning about possible problems and system
instability when users pass acpi_enforce_resources=lax, as suggested
by Len.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Alan Jenkins <sourcejedi.lkml@googlemail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix this problem when CONFIG_THINKPAD_ACPI_HOTKEY_POLL is undefined:
CHECK drivers/platform/x86/thinkpad_acpi.c
drivers/platform/x86/thinkpad_acpi.c:1968:21: error: not an lvalue
CC [M] drivers/platform/x86/thinkpad_acpi.o
drivers/platform/x86/thinkpad_acpi.c: In function 'tpacpi_hotkey_driver_mask_set':
drivers/platform/x86/thinkpad_acpi.c:1968: error: lvalue required as left operand of assignment
Reported-by: Noah Dain <noahdain@gmail.com>
Reported-by: Audrius Kazukauskas <audrius@neutrino.lt>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
The function e1000_enable_tx_pkt_filtering() was removed in
a previous cleanup patch. this removes the no longer used
prototype.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a couple of functions needed to be removed/declared static
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eerd and eewr don't exist on pre PCIe devices
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A large whitespace change to e1000_hw.[ch] in order to update it to kernel coding
style (by running lindent). Updated function header comments into kdoc style.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter was being assigned twice, also clarified variable name and unwrapped
line.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes a bug that occurs when routing packets and simultaneously
changing the mtu. the rx_buffer_len variable is used during the rx cleanup
and if that changes on the fly without stopping traffic bad things happen
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) 82544 does not need last_tx_tso workaround, it interferes with the 82544
workaround too
2) 82544 hang workaround was using the address of the page struct instead of
the physical address as its "workaround decider" not sure how that ever worked
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>