The TI controller on Toshiba Tecra M5 needs more time to power up or
the cards will init incorrectly or not at all.
Signed-off-by: José M. Fernández <josemariafg@gmail.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The goto unmap is too early, we haven't allocated host or done the
request_region().
Found by smatch (http://repo.or.cz/w/smatch.git).
[ Second error path fix by Pierre Ossman ]
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The block layer does not support very low sector count restrictions
so we need to be prepared to handle bigger requests than we can send
directly to the controller.
Problem found by Manuel Lauss.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide-cd: fix REQ_QUIET tests in cdrom_decode_status
Fix up trivial conflicts in include/linux/blkdev.h
* master.kernel.org:/home/rmk/linux-2.6-arm: (45 commits)
[ARM] 5489/1: ARM errata: Data written to the L2 cache can be overwritten with stale data
[ARM] 5490/1: ARM errata: Processor deadlock when a false hazard is created
[ARM] 5487/1: ARM errata: Stale prediction on replaced interworking branch
[ARM] 5488/1: ARM errata: Invalidation of the Instruction Cache operation can fail
davinci: DM644x: NAND: update partitioning
davinci: update DM644x support in preparation for more SoCs
davinci: DM644x: rename board file
davinci: update pin-multiplexing support
davinci: serial: generalize for more SoCs
davinci: DM355 IRQ Definitions
davinci: DM646x: add interrupt number and priorities
davinci: PSC: Clear bits in MDCTL reg before setting new bits
davinci: gpio bugfixes
davinci: add EDMA driver
davinci: timers: use clk_get_rate()
[ARM] pxa/littleton: add missing da9034 touchscreen support
[ARM] pxa/zylonite: configure GPIO18/19 correctly, used by 2 GPIO expanders
[ARM] pxa/zylonite: fix the issue of unused SDATA_IN_1 pin get AC97 not working
[ARM] pxa: make ads7846 on corgi and spitz to sync on HSYNC
[ARM] pxa: remove unused CPU_FREQ_PXA Kconfig symbol
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: document the multi-touch (MT) protocol
Input: add detailed multi-touch finger data report protocol
Input: allow certain EV_ABS events to bypass all filtering
Input: bcm5974 - add documentation for the driver
Input: bcm5974 - augment debug information
Input: bcm5974 - Add support for the Macbook 5 (Unibody)
Input: bcm5974 - add quad-finger tapping
Input: bcm5974 - prepare for a new trackpad header type
Input: appletouch - fix DMA to/from stack buffer
Input: wacom - fix TabletPC touch bug
Input: lifebook - add DMI entry for Fujitsu B-2130
Input: ALPS - add signature for Toshiba Satellite Pro M10
Input: elantech - make sure touchpad is really in absolute mode
Input: elantech - provide a workaround for jumpy cursor on firmware 2.34
Input: ucb1400 - use disable_irq_nosync() in irq handler
Input: tsc2007 - use disable_irq_nosync() in irq handler
Input: sa1111ps2 - use disable_irq_nosync() in irq handlers
Input: omap-keypad - use disable_irq_nosync() in irq handler
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: fix oops in hid_check_keys_pressed()
HID: fix possible deadlock in usbhid_close()
HID: Fix the support for apple mini aluminium keyboard
HID: Add support for the G25 force feedback wheel in native mode
HID: hidraw -- fix missing unlocks in unlocked_ioctl
Fix the display of a few fields in the iBFT NIC attribute structure in
sysfs.
Ensure that, if the DHCP IP address and the subnet mask for the interface
is present in the iBFT NIC structure, the corresponding entries are
created in sysfs tree for the device. This would hence create the
additional entries in the tree based on the iBFT table and would not
delete any existing entries.
Signed-off-by: Ashutosh Naik <ashutosh.naik@gmail.com>
Cc: Vishnu V <vishnu@chelsio.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Uwe Geuder noted that he gets random bitmaps on a text console if he tried
to type extended characters (like the e acute). For him everything above
unicode 0xa0 was corrupted.
After some digging there seems to be a little culprit in vgacon since the
beginning of ages (well git). The function vgacon_font_get will store the
number of characters correctly in font->charcount but then calls to
vgacon_do_font_op(..., 0, 0). Which means only the lower 256 characters
are actually stored to the fontdata. The rest is left untouched. So the
next time that saved data is used, the garbled font appears. This happens
on every switch between text consoles.
Addresses https://bugs.launchpad.net/ubuntu/+source/linux/+bug/355057
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Tested-by: Uwe Geuder <ubuntuLp-ugeuder@sneakemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/serial/crisv10.c:4428: error: unknown field 'read_proc' specified in initializer
Commit 0f043a81eb ("proc tty: remove struct
tty_operations::read_proc") removes the read_proc entry from struct
tty_operations.
Rework the proc handling in the CRISv10 serial driver to use proc_fops
instead.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Doing it in reverse order causes uevent to be sent before
we have a MAC address, which confuses udev.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
acpi_rs_get_pci_routing_table_length is not performing sufficient
validation on the package returned from _PRT. It assumes a package of
packages and fails/faults if this is not the case.
We should validate each subpackage when extracted from the parent
package, and not accept objects of the wrong type, since that will just
cause the scanning to fail (likely with a kernel oops).
This can only happen with a serious BIOS bug, and is accompanied by a
warning something like this:
ACPI Warning (nspredef-0949): \_SB_.PCI0.PEG4._PRT: Return Package type mismatch at index 0 - found Integer, expected Package [20090320]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We were avoiding calling sg_init* on scatterlists passed
into virtnet_send_command to prevent extraneous end markers.
This caused build warnings for uninitialized variables.
Cleanup the code to create proper scatterlists.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the cleanup in bond_create nicer :) Also now the forgotten
free_netdev is called.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN9512 and LAN9514 are USB hubs with an integrated 10/100 ethernet
controller. Logically this looks like an ethernet controller (similar
to LAN9500) permanently attached to one of the hub's downstream ports.
This patch adds the usb device id of the new ethernet controller to the
smsc95xx driver. This id is the same in both new devices.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMSC LAN9500 has dual purpose GPIO/LED pins, and by default at power-on
these are configured as GPIOs. This means that if LEDs are fitted they
won't ever light.
This patch sets them to be LED outputs for speed, duplex and
link/activity.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netconsole is loaded and a network interface fades away (e.g. on
rmmod $interface_driver_module) the rmmod remains stuck and some locks
are taken that prevent any additional module loading/unloading as well
as interface up/down changes.
In addition kernel logs (and console) get flooded at 10s interval with
[ 122.464065] unregister_netdevice: waiting for eth0 to become free. Usage count = 1
[ 132.704059] unregister_netdevice: waiting for eth0 to become free. Usage count = 1
This patch lets netconsole take NETDEV_UNREGISTER event into account
and release the affected interface if it was in use.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_slave_info_query() should keep a read lock while accessing slave info,
or risk accessing stale data and corruption.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device is not claimed by hid-input (i.e devices driver by userspace
hiddev/hidraw-based drivers, or completely detached from HID
and driver by libusb), we must not check the hid->inptus, as it
is not guaranteed to be initialized, as this is performed only for devices
handled by hid-input.
Reported-by: Guillaume Chazarain <guichaz@gmail.com>
Tested-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Trivial: fixing gcc 4.4 compiler warning:
drivers/net/cxgb3/t3_hw.c: In function ‘t3_prep_adapter’:
drivers/net/cxgb3/t3_hw.c:3782: warning: suggest parentheses around operand of ‘!’ or change ‘|’ to ‘||’ or ‘!’ to ‘~’
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@mail.by>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the UDIVSLOT register on the newer UART blocks
which gives the capability of 1/16ths adjustment to the baud rate.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This makes software fallbacks not do tiling wrong on i965 and later after
resume. It also should fix 945 performance reduction after resume which
would have disabled tiling without causing any visible effect.
Signed-off-by: Keith Packard <keithp@keithp.com>
[anholt: Fixed up the 915 case to not save/restore the new regs]
Signed-off-by: Eric Anholt <eric@anholt.net>
i386 has inline code for writeq and readq, so just use those instead of ugly
macros which evaluate arguments multiple times.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Original patch (dfa4411cc3) was buggy.
This is a more proper fix which introduces blk_rq_quiet() macro
alleviating the need for dumb, too short caching variables.
Thanks to Helge Deller and Bart for debugging this.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Reported-and-tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On several mv643xx_eth hardware versions, the two 64bit mib counters
for 'good octets received' and 'good octets sent' are actually 32bit
counters, and reading from the upper half of the register has the same
effect as reading from the lower half of the register: an atomic
read-and-clear of the entire 32bit counter value. This can under heavy
traffic occasionally lead to small numbers being added to the upper
half of the 64bit mib counter even though no 32bit wrap has occured.
Since we poll the mib counters at least every 30 seconds anyway, we
might as well just skip the reads of the upper halves of the hardware
counters without breaking the stats, which this patch does.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when OOM occurs during rx ring refill, mv643xx_eth will get
into an infinite loop, due to the refill function setting the OOM bit
but not clearing the 'rx refill needed' bit for this queue, while the
calling function (the NAPI poll handler) will call the refill function
in a loop until the 'rx refill needed' bit goes off, without checking
the OOM bit.
This patch fixes this by checking the OOM bit in the NAPI poll handler
before attempting to do rx refill. This means that once OOM occurs,
we won't try to do any memory allocations again until the next invocation
of the poll handler.
While we're at it, change the OOM flag to be a single bit instead of
one bit per receive queue since OOM is a system state rather than a
per-queue state, and cancel the OOM timer on entry to the NAPI poll
handler if it's running to prevent it from firing when we've already
come out of OOM.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
When the SQ is flushed, mark the flushed entries as not signaled so
the poll logic doesn't re-insert the CQ entry thinking its an out of
order completion.
The bug can cause the NFS/RDMA server to crash due to processing the
same completed work request twice.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A regression was introduced in hg changeset 33810c734a0d, which resulted in
a kernel panic whenever the device was disconnected from USB. The call to
4l2_device_register() was overwriting the pointer for usb_set_intfdata(), so
when au0828_usb_disconnect() was called, the usb_get_intfdata() returned a
pointer to the v4l2_device instead of the au0828_dev structure.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Two fixes for DViCO FusionHDTV DVB-T Dual Express:
* Reset correct tuner when reinitializing xc3028.
* Disable the I2C gate control to avoid locking up the I2C bus.
Tested-by: John Knops <jknops@australiaonline.net.au>
Reviewed-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Christopher Pascoe <linuxdvb@itee.uq.edu.au>
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
set_modeready flag must be set before command sent to USB in
s2255_write_config.
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Return actual error values as returned by the i2c subsystem, rather
than 0 or 1.
* If the registration of the second bus fails, unregister the first one
before exiting, otherwise we are leaking resources.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently drivers/media drivers are linked very early - directly after
base, block, misc, and mfd and before ata, scsi, ide, input, firewire,
usb, and i2c. This breaks static build of video4linux drivers, that use
generic CPU i2c adapter drivers and the v4l2-subdev subsystem, because
during video4linux probing the v4l2-subdev core requires a struct
i2c_adapter context, which cannot be satisfied before the i2c subsystem is
initialised. Moving drivers/media after drivers/i2c fixes this problem.
The best way to trigger action is by submitting a patch:-) So, let's see
what comes out of it - on the one hand I don't see any reason why media
has to be linked this early, and nobody was able to give me one yesterday
as this problem has been discussed on linux-media, OTOH, maybe indeed it
would be better to move i2c the whole way up above media, but that'd be
much bigger of a change, I think.
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I lowered the kfree(t) down a couple lines and removed the superflous
"t->vdev = NULL;"
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I moved the kfree() down a couple lines. t->vdev is going to be in freed
memory so there is no point setting it to NULL. I added a kfree(t) on a
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
selecting ALSA module breaks if !SND. Just remove select.
While here, let's fix the whitespacing at the Kconfig.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A late v4l2_subdev framework change accidentally sent the audio input
routing value to the external multiplexer, instead of the muxer input routing
value to the external multiplexer. This change corrects that error.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch switches usbhid_close() from flush_scheduled_work() to canceling
the outstanding work. This fixes a possible deadlock due to work taking
the mutex usbhid_close() holds. Lockdep reported the problem.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
--
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (24 commits)
e100: do not go D3 in shutdown unless system is powering off
netfilter: revised locking for x_tables
Bluetooth: Fix connection establishment with low security requirement
Bluetooth: Add different pairing timeout for Legacy Pairing
Bluetooth: Ensure that HCI sysfs add/del is preempt safe
net: Avoid extra wakeups of threads blocked in wait_for_packet()
net: Fix typo in net_device_ops description.
ipv4: Limit size of route cache hash table
Add reference to CAPI 2.0 standard
Documentation/isdn/INTERFACE.CAPI
update Documentation/isdn/00-INDEX
ixgbe: Fix WoL functionality for 82599 KX4 devices
veth: prevent oops caused by netdev destructor
xfrm: wrong hash value for temporary SA
forcedeth: tx timeout fix
net: Fix LL_MAX_HEADER for CONFIG_TR_MODULE
mlx4_en: Handle page allocation failure during receive
mlx4_en: Fix cleanup flow on cq activation
vlan: update vlan carrier state for admin up/down
netfilter: xt_recent: fix stack overread in compat code
...
Quirks for the apple mini keyboard was recently added but keyboard
was recognized as a powerbook keyboard. Adjusted boundary to the lowest
product id for the apple mini keyboard to get the right translation.
Signed-off-by: Ulrich Dangel <uli@spamt.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a logic error in "whole chip erase" for the m25p80 family. If
the whole device is successfully erased, erase_chip() will return 0, and
the code will fall through to the "else" clause, and do sector-by-sector
erase in addition to the whole-chip erase. This patch corrects that.
Also, the MAX_READY_WAIT_COUNT is insufficient for an m25p16 connected
to a 400 MHz powerpc. Increasing it allows me to successfully program
the device on my board.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After experimenting with kexec with the last merges after 2.6.29, I've
had some problems when probing e100. It would not read the eeprom. After
some bisects, I realized this has been like that since forever (at least
2.6.18). The problem is that shutdown is doing the same thing that
suspend does and puts the device in D3 state. I couldn't find a way to
get the device back to a sane state in the probe function. So, based on
some similar patches from Rafael J. Wysocki for e1000, e1000e, and ixgbe,
I wrote this one for e100.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix up error path leak in i915_cmdbuffer
drm/i915: fix unpaired i915 device mutex on entervt failure.
drm/i915: add support for G41 chipset
drm/i915: Enable ASLE if present
drm/i915: Unregister ACPI video driver when exiting
drm/i915: Register ACPI video even when not modesetting
drm/i915: fix transition to I915_TILING_NONE
drm/i915: Don't let an oops get triggered from irq_emit without dma init.
drm/i915: allow tiled front buffers on 965+
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (21 commits)
RDMA/nes: Update iw_nes version
RDMA/nes: Fix error path in nes_accept()
RDMA/nes: Fix hang issues for large cluster dynamic connections
RDMA/nes: Increase rexmit timeout interval
RDMA/nes: Check for sequence number wrap-around
RDMA/nes: Do not set apbvt entry for loopback
RDMA/nes: Fix unused variable compile warning when INFINIBAND_NES_DEBUG=n
RDMA/nes: Fix fw_ver in /sys
RDMA/nes: Set trace length to 1 inch for SFP_D
RDMA/nes: Enable repause timer for port 1
RDMA/nes: Correct CDR loop filter setting for port 1
RDMA/nes: Modify thermo mitigation to flip SerDes1 ref clk to internal
RDMA/nes: Fix resource issues in nes_create_cq() and nes_destroy_cq()
RDMA/nes: Remove root_256()'s unused pbl_count_256 parameter
mlx4_core: Fix memory leak in mlx4_enable_msi_x()
IB/mthca: Fix timeout for INIT_HCA and a few other commands
RDMA/cxgb3: Don't zero QP attrs when moving to IDLE
RDMA/nes: Fix bugs in nes_reg_phys_mr()
RDMA/nes: Fix compiler warning at nes_verbs.c:1955
IPoIB: Disable NAPI while CQ is being drained
...
char bname[5] is too small for the string "X GHz" when the null
terminator is taken into account. Thus, turning on rate debugging
can crash unless we have lucky stack alignment.
Cc: stable@kernel.org
Reported-by: Paride Legovini <legovini@spiro.fisica.unipd.it>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Under certain circumstances iwlwifi can get stuck and will no
longer accept scan requests, because the core code (cfg80211)
thinks that it's still processing one. This fixes one of the
points where it can happen, but I've still seen it (although
only with my radio-off-when-idle patch).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wext_link_change() might be called from rndis_command() at
initialization stage and priv->workqueue/priv->work have not been
initialized yet. This causes invalid opcode at rndis_wext_bind on
some brands of bcm4320.
Fix by initializing workqueue/workers in rndis_wext_bind() before
rndis_command is used.
This bug has existed since 2.6.25, reported at:
http://bugzilla.kernel.org/show_bug.cgi?id=12794
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/iwlwifi/iwl3945-base.c:1415: error: __ksymtab_iwl3945_rx_queue_reset causes a section type conflict
I am pretty sure that this is a compiler bug, so not to worry. However,
as far as I can see, iwl-3945.o (the only user) and iwl3945-base.o are
always linked into the same module, so the EXPORT_SYMBOL (which causes
the problem) should not be needed. Correct?
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hd dance around local irq and HD_IRQ enable without achieving much.
It ends up transferring data from irq handler with both local irq and
HD_IRQ disabled. The only place it actually does something is while
transferring the first block of a request which it does with HD_IRQ
disabled but local irq enabled.
Unfortunately, the dancing is horribly broken from locking POV. IRQ
and timeout handlers access block queue without grabbing the queue
lock and running the driver in SMP configuration crashes the whole
machine pretty quickly.
Remove meaningless irq enable/disable dancing and add proper locking
in issue, irq and timeout paths.
Signed-off-by: Tejun Heo <tj@kernel.org>
drivers/block/mg_disk.c: In function ‘mg_dump_status’:
drivers/block/mg_disk.c:265: warning: format ‘%ld’ expects type ‘long int’, but
argument 2 has type ‘sector_t’
[ Impact: kill build warning ]
Cc: unsik Kim <donari75@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
IRQ and timeout handlers call functions which expect locked queue lock
without locking it. Fix it.
While at it, convert 0s used as null pointer constant to NULLs.
[ Impact: fix locking, cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: unsik Kim <donari75@gmail.com>
Default voltage constraints were being provided for fixed voltage
regulator where board constraints were not provided but these constraints
used INT_MIN as the default minimum voltage which is not a valid value
since it is less than zero. Use 1uV instead.
Also set the default values we set in the constraints themselves since
otherwise the max_uV constraint we determine will not be stored in the
actual constraint strucutre and will therefore not be used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This seems to be fallout from last October's regulator core rework.
It got noticed only because of recent regulator framework changes.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
During regulator registration, any error after device_register() will
cause a double-free on the struct regulator_dev 'rdev'. The bug is in
drivers/regulator/core.c:regulator_register():
...
scrub:
device_unregister(&rdev->dev);
clean:
kfree(rdev); <---
rdev = ERR_PTR(ret);
goto out;
...
device_unregister() calls regulator_dev_release() which frees rdev. The
subsequent kfree corrupts memory and causes some OMAP3 systems to oops on
boot in regulator_get().
Applies against 2.6.30-rc3.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When regulator_desc->type is something different from REGULATOR_VOLTAGE or REGULATOR_CURRENT
the if should probably return ERR_PTR(-EINVAL)
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
@@ expression E; constant C; @@
(
- !E == C
+ E != C
)
Signed-off-by: Diego Liziero <diegoliz@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
I removed the extra semi-colon and indented the return statement.
The unreachable code was found by smatch (http://repo.or.cz/w/smatch.git).
The patch was compile tested.
regards,
dan carpenter
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In order to utilize the full power of the new multi-touch devices, a
way to report detailed finger data to user space is needed. This patch
adds a multi-touch (MT) protocol which allows drivers to report details
for an arbitrary number of fingers.
The driver sends a SYN_MT_REPORT event via the input_mt_sync() function
when a complete finger has been reported.
In order to stay compatible with existing applications, the data
reported in a finger packet must not be recognized as single-touch
events. In addition, all finger data must bypass input filtering,
since subsequent events of the same type refer to different fingers.
A set of ABS_MT events with the desired properties are defined. The
events are divided into categories, to allow for partial implementation.
The minimum set consists of ABS_MT_TOUCH_MAJOR, ABS_MT_POSITION_X and
ABS_MT_POSITION_Y, which allows for multiple fingers to be tracked.
If the device supports it, the ABS_MT_WIDTH_MAJOR may be used to provide
the size of the approaching finger. Anisotropy and direction may be
specified with ABS_MT_TOUCH_MINOR, ABS_MT_WIDTH_MINOR and
ABS_MT_ORIENTATION. Devices with more granular information may specify
general shapes as blobs, i.e., as a sequence of rectangular shapes
grouped together by a ABS_MT_BLOB_ID. Finally, the ABS_MT_TOOL_TYPE
may be used to specify whether the touching tool is a finger or a pen.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With the upcoming multi-touch interface as an example, there is
a need to make certain that all reported events actually get passed
to the event handler. This patch equips the input core with the
ability to bypass all filtering for certain EV_ABS events.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for the new unibody Macbook, with physically
integrated button and trackpad. Since the integrated button changes
the logic for touch-and-click, a device capability bit mask is now
reported in input_id.version, which can be picked up by user space
via a EVIOCGID call.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: David M. Lary <dmlary@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The integrated button on the new unibody Macbooks presents a need to
report explicit four-finger actions. Evidently, the finger pressing
the button is also touching the trackpad, so in order to fully support
three-finger actions, the driver must be able to report four-finger
actions. This patch adds a new button, BTN_TOOL_QUADTAP, which
achieves this.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The new unibody Macbooks are equipped with an integrated button and
trackpad. The package header of the trackpad interface has changed to
also contain information about the integrated button. This patch
performs the necessary preparations to allow for the new package
header.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CONFIG_DMA_API_DEBUG spotted an instance of appletouch using
an array on the stack as a DMA buffer for certain hardware.
Change it to use a kmalloc()ed buffer instead.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixed a bug that was introduced in kernel 2.6.28 for
TabletPC touch data. The wacom_parse_hid routine in wacom_sys.c
should always return 0 even when usb_control_msg got an error.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If reg_phys_mem() fails, we need to free memory allocated for MPA
frame with private data before returning the error. Also move
nes_add_ref() after the reg_phys_mem() is successful.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Running large cluster setup, we are hanging after many hours of
testing. Fixing this required going over the code and making sure the
rexmit entry was properly removed based on the cm_node's state and
packet received. Also when receiving a FIN packet, check seq# and
make sure there were no errors before calling handle_fin().
Following are the changes done in nes_cm.c:
* handle_ack_pkt() needs to return error value, so in case of error,
handle_fin() is not called. Some cleanup done while going over the code.
* handle_rst_pkt(), handling of cm_node's NES_CM_STATE_LAST_ACK is missing.
* process_packet(), in case of FIN only packet is received, call
check_seq() before processing.
* in handle_fin_pkt(), we are calling cleanup_retrans_entry() for all
conditions, even if the packets need to be dropped.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Under heavy load with large cluster testing, it may take longer to
receive a response to MPA requests. Change the driver to wait longer
after each rexmit to max time value.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
check_seq() was not checking if the seq#s have wrapped. Fix it.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a connect request comes, apbvt should only be set for
non-loopback connections.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove the NES_DEBUG that is causing the compile warning about an
unused variable when INFINIBAND_NES_DEBUG is not enabled.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
/sys/class/infiniband/nes?/fw_ver is not displaying firmware version
properly (it shows 0.0.0 with the current code). Fill in the correct
firmware version number.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With updated PHY firmware for SFP_D, setting the trace length to 1
inch for SFP_D provides a more stable link.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable repause timer for port 1. Without this setting, under stress,
the chip may misbehave.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In commit 1b949324 ("RDMA/nes: Fix SFP+ PHY initialization") there is
a mistake in the clean up code that removed port 1 CDR loop filter
settings for 10G cards other than CX4. Put the correct setting back
for appropriate PHY types.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change thermo mitigation code to flip the SerDes1 reference clock to
internal, to match the change in commit a4849fc1 ("RDMA/nes: Add
wide_ppm_offset parm for switch compatibility").
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This reverts commit 8032b526d1.
Hey, it was only meant to be a single release. Now they can all die as
far as I'm concerned.
[ Just kidding. They're cute and cuddly.
Except when they have horrible nasty facial diseases. Oh, and I guess
they're not actually that cuddly even when disease-free. ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: only save/restore existent registers in the PCIe capability
x86/PCI: don't bother with root quirks if _CRS is used
docbooks: add/fix PCI kernel-doc
PCI: cleanup debug output resources
x86/PCI: set_pci_bus_resources_arch_default cleanups
x86/PCI: Move set_pci_bus_resources_arch_default into arch/x86
x86/PCI: don't call e820_all_mapped with -1 in the mmconfig case
PCI quirk: disable MSI on VIA VT3364 chipsets
OSC's OSD2 target: [git clone git://git.open-osd.org/osc-osd/ master]
(Initiator code prior to this patch must use: "git checkout CDB_VER_OSD2r01"
in the target tree above)
This is a summery of the wire changes:
* OSDv2_ADDITIONAL_CDB_LENGTH == 192 => 228 (Total CDB is now 236 bytes)
* Attributes List Element Header grew, so attribute values are 8 bytes
aligned.
* Cryptographic keys and signatures are 20 => 32
* Few new definitions.
(Still missing new standard definitions attribute values, these do not change
wire format and will be added later when needed)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In OSD2r04 draft, cryptographic key size changed to 32 bytes from
OSD1's 20 bytes. This causes a couple of on-the-wire structures
to change, including the CDB.
In this patch the OSD1/OSD2 handling is separated out in regard
to affected structures, but on-the-wire is still the same. All
on the wire changes will be submitted in one patch for bisect-ability.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In OSD2r05 draft each attribute list element header was changed
so attribute-value would be 8 bytes aligned. In OSD2r01-r04
it was aligned on 2 bytes. (This is because in OSD2r01 the complete
element was 8 bytes padded at end but the header was not adjusted
and caused permanent miss-alignment.)
OSD1 elements are not padded and might be or might not be aligned.
OSD1 is still supported.
In this code we do all the code re-factoring to separate OSD1/OSD2
differences but do not change actual wire format. All wire format
changes will happen in one patch later, for bisect-ability.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bio_map_kern() returns an ERR_PTR() not NULL.
Found by smatch (http://repo.or.cz/w/smatch.git). Compile tested.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Here's a fix for hotplug events. The useage of queue_delayed_work seems
to broke the fifo for processing of firmware events. After several iterations
of adding and removing cabling connected to jbods, the devices are not
getting added becuase kernel thread is activited out of order.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Diagnostic buffer support is already there in the driver. This support allows
applications to pull ring buffers from controller firmware for debugging
firmware related issues.
What this patch does is sends reqeust to firmware to release the buffers prior
to host reset. This will allow what ever debug info is there prior to reset
to be dma'd to host memory. With out this fix, some of the debug data would
been lost.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Bug fix in the broadcast primative async event code where the driver would
stop sending tm queries after the first queury was completed. This was due
driver not reseting the tm_cmds.status field back to MPT2_CMD_NOT_USED after
completing a task management request.
An addtional fix adding sanity check to insure sas_device->starget set to NULL.
During multipath testing fail over/fail back, the mid layer was holding onto
sdev longer than the fail back period, thus starget was getting set to NULL
for device being added.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Dell branding along with the VID, DID, SSVID, SSDID following the LSI
branding that contains the card firmware/chip/bios versions. If the SSDID
is not known but it is a Dell HBA, the driver will print the SSDID instead
of the Dell branding string. Nothing will be printed for non Dell HBAs
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The driver name needs to be at the beginining of the driver_version string in
MPT2IOCINFO ioctl. This is the same behaviour is there already in the mptsas
driver.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The driver is not freeing message frame when returning failure from
_ctl_do_task_abort. If you call this function 500 times when its unable
to find an active task mid, you end up with no message frames.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is a bug in firmware where the reply message frame says there is a
16kb sense buffer, when in reality its only 20 bytes. This fix insures
the memcpy action doesn't corrupte the memory beyond the 90 bytes allocated in
the scsi command for sense buffer.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The poison sanity check on the reply_post_free register needs to be by 32bit,
not 64bit. The poison check is there because its possible that the driver read
the 1st 32bit before the 2nd 32bit has been written to by firmware. In other
words, this handles race between driver reading the 64 bit register, and it
being dma'd across pci memory from controller firmware as two 32bit pci writes.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current magic number is shared with mptsas driver. This to be unique to
fix issues with register_ioctls32_conversion in older kernels. We are making
this change across all versions of the sas2.0 drivers.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Shifting an unsigned char implicitly casts it to a signed int. This
caused 'lba' to sign-extend and Linux would then try READ CAPACITY 16
which was not supported by at least one drive. Using the
get_unaligned_be*() helpers keeps us from having to worry about how the
extension might occur.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ata_sas_slave_configure was changed such that it now allocates
some memory for a drain buffer for ATAPI devices. Fixup the ipr
driver such that we no longer make this call with interrupts disabled.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The FCoE forwarder (FCF) would be selected, but then would soon time
out after three advertisements were missed. This would be 24 seconds
by default, or 3 times the keep-alive interval configured on the switch.
The cause was that the multicast address for all FIP E-nodes
was never added.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When building with a .config generated from 'make allmodconfig'
some build warnings are generated. This patch corrects the warnings,
adds a FC_FID_NONE (= 0) enumeration for FC-IDs and cleans up one
variable naming to meet our variable naming conventions. For example,
fc_lport's should be named "lport," not "lp."
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
These probably never should have been exported.
If they were needed outside of the fcoe module, they
would have been moved to libfcoe.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sk_buff pointers should use kfree_skb() instead of vanilla kfree().
Found by smatch (http://repo.or.cz/w/smatch.git).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When a delete event is queued for an rport, set state to NONE so that no
other processing is done on the rport as it is being removed.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After lport_destroy, the local port should not be used again. Transition
to state NONE, any incoming frames or link up should not transition out
of this state since we are deleting exchange table and cleaning up the
local port. Also, mark link as down.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We want to generate the rport queue event (from the logoff)
before flushing the queue otherwise the event may still be
in the queue when we logoff.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rogue ports are currently not tracked on any list. The only reference
to them is through any outstanding exchanges pending on the rogue ports.
If the module is removed while a retry is set on a rogue port
(say a Plogi retry for instance), this retry is not cancelled because there
is no reference to the rogue port in the discovery rports list. Thus the
local port can clean itself up, delete the exchange pool, and then the
rogue port timeout can fire and try to start up another exchange.
This patch tracks the rogue ports in a new list disc->rogue_rports. Creating
a new list instead of using the disc->rports list keeps remote port code
change to a minimum.
1) Whenever a rogue port is created, it is immediately added to the
disc->rogue_rports list.
2) When the rogues port goes to ready, it is removed from the rogue list
and the real remote port is added to the disc->rports list
3) The removal of the rogue from the disc->rogue_rports list is done in
the context of the fc_rport_work() workQ thread in discovery callback.
4) Real rports are removed from the disc->rports list like before. Lookup
is done only in the real rports list. This avoids making large changes
to the remote port code.
5) In fc_disc_stop_rports, the rogues list is traversed in addition to the
real list to stop the rogue ports and issue logoffs on them. This way, rogue
ports get cleaned up when the local port goes away.
6) rogue remote ports are not removed from the list right away, but
removed late in fc_rport_work() context, multiple threads can find the same
remote port in the list and call rport_logoff(). Rport_logoff() only
continues with the logoff if port is not in NONE state, thus preventing
multiple logoffs and multiple list deletions.
7) Since the rport is removed from the disc list at a later stage
(in the disc callback), incoming frames can find the rport even if
rport_logoff() has been called on the rport. When rport_logoff() is called,
the rport state is set to NONE, and we are trying to cancel all exchanges
and retries on that port. While in this state, if an incoming
Plogi/Prli/Logo or other frames match the rport, we should not reply
because the rport is in the NONE state. Just drop the frame, since the
rport will be deleted soon in the disc callback (fc_rport_work)
8) In fc_disc_single(), remove rport lookup and call to fc_disc_del_target.
fc_disc_single() is called from recv_rscn_req() where rport lookup
and rport_logoff is already done.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For instance, if there is a Plogi pending (remote port is in Plogi state),
and the state changes to say NONE (because the port is being logged off),
then when the Plogi resp times out, do not start a retry.
This patch partially reverts an earlier patch (libfc: check for err when
recv and state is incorrect), by moving the state check back to before
checking for error. However, if the state does not match, then there is
an additional check to see if its an error ptr or a real frame before
jumping to err or out respectively.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
gpn_ft_resp processing currently does not hold the discovery lock.
disc_done() thus gets called from gpn_ft_resp or from gpn_ft_parse
without the lock held. This then sets disc->pending to zero or calls
gpn_ft_req() without disc_lock held.
- Hold disc mutex during gpn_ft resp processing
- In disc_done, release the disc mutex while calling lport callback
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
(version 2)
Fixed a bug in calculating ddp map range when search for free entries:
it was going beyond the end by one, thus corrupting gl_skb[0].
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When doing a lot (128) of large writes (256K) we can hit the cxgb3_snd_win
check pretty easily. The driver's xmit thread then takes 100% of the cpu.
The driver should not be returning -EAGAIN for this problem. It should
be returing -ENOBUFS, then when the window is opened again it should
queue the xmit thread (it already wakes the xmit thread).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
cxgb3i was setting can_queue to only 128 commands, and was
setting the can_queue and cmd_per_lun to the same value.
This sets the can_queue to 1024 commands, and sets the cmd_per_lun
to a safer default of 32.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set target can queue limit to the number of preallocated
session tasks we have.
This along with the cxgb3i can_queue patch will fix a throughput
problem where it could only queue one LU worth of data at a time.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If a command's scsi cmd pdu setup fails then we can just fail
the IO to the scsi layer. If a DATA_OUT for a R2T fails then
we will want to drop the session, because it means we got a
bad request from the target (iscsi protocol error).
This patch has us propogate the error upwards so libiscsi_tcp
or libiscsi can decide what the best action is to take. It
also fixes a bug where we could try to grab the session lock
while holding it, because if iscsi_tcp drops the session in the
pdu setup callout the session lock is held when setting up the
scsi cmd pdu.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The zfcp_port might have been removed, while the FC fast_io_fail timer
is still running and could trigger the terminate_rport_io callback.
Set the pointer to the zfcp_port to NULL and check accordingly
before using it.
Reviewed-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Before dropping the reference count with zfcp_adapter_put, increase it
with zfcp_adapter_get when issuing cfdc requests.
Reviewed-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If this problem appears zfcp ports cannot be de-queued since it is
checked for a zero refcount. The port reference counting is wrong for
existing zfcp ports when e.g. an adapter gets on-line again. During
port scanning the reference counting for existing ports should not be
changed.
Signed-off-by: Martin Petermann <martin.petermann@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current sbal counting can be wrong if a fsf request is
waiting for free sbals and at the same time qdio request queue
is shutdown and re-opened. Revering a previous patch fixes this
issue.
Signed-off-by: Martin Petermann <martin.petermann@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When the abort handler cannot find a pending FSF request, the request
completion could just be running. This means we cannot return SUCCESS,
since this would lead to call to scsi_done after exiting the SCSI
error handler which is not allowed.
Reviewed-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
A remote port remains in error state even if we receive a RSCN
stating that the connection is re-established. The port recovery
is not started due to a flag which is not reset.
The solution is to clear the flag in question before we trigger a ERP.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Error codes specific to the control file requests are evaluated by the
actcli tool, so don't report -ENXIO for those. Generic problems are
still checked for outside the command specific handler.
Reviewed-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
On some hardware it can take some time to add a unit. If
some remove this unit during this process the remove will
fail.
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The remote port remains in error state even if the connection
is re-established. A wrong precondition check was performed on
the port status leading to a cancellation of the port reopen.
Remove the pre-req check because it's not required and better
handled within the ERP.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ERP thread is performing a task before it is executing the
corresponding down on the semaphore. The response handler of the
just started exchange config should wait for the completion by
performing a down on this semaphore. Since this semaphore is still
positive from the ERP enqueue the handler won't wait and therefore
the exchange config will always fail leaving the adapter in error.
The problem can be solved by performing the down on the semaphore
before starting an ERP task. This is the logically correct order.
Only walk the ERP loop if there is a task to perform.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The nameserver port might be in state online when the adapter is
offlined. On adapter reactivation the nameserver port is not
re-opened due to the PORT_ONLINE status. This results in an
unsuccessful recovery. In forcing the nameserver port status
to offline on all adapter offline events this issue is prevented.
Waiting for the reference count to drop to zero in
zfcp_wka_port_offline is not required, so remove it.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When running the scsi_scan from the zfcp workqueue and the target
device does not respond, the zfcp workqueue can block until the
scsi_scan hits a timeout. Move the work to the scsi host workqueue,
since this one is also used for the scan from the SCSI midlayer.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix problem that zfcp_fsf_exchange_config_data_sync and
zfcp_fsf_exchange_config_data_sync could try to call zfcp_fsf_req_free
with a NULL pointer.
Reviewed-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since we're setting the host port type now to FC_PORTTYPE_NPIV
for adapters running in NPIV mode we should allow this port type
for auto-port scanning as well.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Avoid referencing a fsf request after sending it in fcp_fsf_req_send,
it might have already completed and deallocated.
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We cannot call blk_plug_device from scsi_target_queue_ready
because the q lock is not held. And we do not need to call
it from there because when we return 0, the scsi_request_fn
not_ready handling will plug the queue for us if needed.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update driver version to 8.3.1
Also update copyright end year for driver.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
8.3.1 Fixes/Changes :
- Fix incorrect byte-swapping on word 4 of IOCB (data length) which
caused LUNs to not be discovered on big-endian (e.g. PPC)
- Remove a bad cast of MBslimaddr which loses the __iomem (sparse)
- Make lpfc_debugfs_mask_disc_trc static (sparse)
- Correct misspelled word BlockGuard in lpfc_logmsg.h comment
- Replaced repeated code segment for canceling IOCBs from a list with
a function call, lpfc_sli_cancel_iocbs().
- Increased HBQ buffers to support 40KB SSC sequences.
- Added sysfs interface to update speed and topology parameter without
link bounce.
- Fixed bug with sysfs fc_host WWNs not being updated after changing
the WWNs.
- Check if the active mailbox is NULL in the beginning of the mailbox
timeout handler - fixes panic in the mailbox timeout handler while
running IO stress test
- Fixed system panic in lpfc_pci_remove_one() due to ndlp indirect
reference to phba through vport
- Removed de-reference of scsi device after call to scsi_done() to fix
panic in scsi completion path while accessing scsi device after
scsi_done is called.
- Fixed "Nodelist not empty" message when unloading the driver after
target reboot test
- Added LP2105 HBA model description
- Added code to print all 16 words of unrecognized ASYNC events
- Fixed memory leak in vport create + delete loop
- Added support for handling dual error bit from HBA
- Fixed a driver NULL pointer dereference in lpfc_sli_process_sol_iocb
- Fixed a discovery bug with FC switch reboot in lpfc_setup_disc_node
- Take NULL termintator into account when calculating available buffer space
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
blk_rq_unmap_user() returns EFAULT if a program passes an invalid
address to kernel (the kernel fails to copy data to user space). sg
needs to pass the returned value to user space instead of ignoring
it. Before the block layer conversion, sg returns EFAULT
properly. This restores the old behavior.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
So, what's happening here is that the drive is reporting a sense of
2/4/1 ("logical unit is becoming ready") from sr_test_unit_ready(), and
then we ask for the media event notification before checking that result
at all. The check_media_event_descriptor() call isn't getting a check
condition, but it's also reporting that the tray is closed and that
there's no media. In actuality it doesn't yet know if there's media or
not, but there's no way to express that in the media event status field.
My current thought is that if it told us the device isn't yet ready, we
should return that immediately, since there's nothing that'll tell us
any more data than that reliably:
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
isdn: document Kernel CAPI driver interface
Create a file Documentation/isdn/INTERFACE.CAPI describing the
interface between the kernel CAPI subsystem and ISDN device drivers,
analogous to the existing Documentation/isdn/INTERFACE for the old
isdn4linux subsystem. Also add kerneldoc comments to the exported
functions in drivers/isdn/capi/kcapi.c.
Impact: Documentation
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code writes the PME enabled bit in PCI config space which is
wrong. This was needed for pre-release hardware, and was not removed from
the driver. Also, we need to clear the WUS (wake up status) after we
resume. Otherwise we can't wake for the same event again since it's still
asserted in the hardware. Plus, the multicast lists were being written
improperly, causing multicast WoL to fail.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Stephen Hemminger <shemminger@vyatta.com>
The veth driver will oops if sysfs hooks are open while module is removed.
The net device destructor can not point to code in a module; basically
there are only two possible safe values: NULL - no destructor, or
free_netdev - free on last use
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the tx_timeout() to properly handle the clean up of the
tx ring. It also sets the tx put pointer back to the correct position to
be in sync with HW.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we failed to allocate new fragments for receive buffer,
the packet should be dropped and packets should be reused.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of mlx4_en_activate_cq() failure, the cleanup
code would go to rx_err and try to disable unactivated rings.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we already have entry for ZEPHYR the match is done
on product name whereas B-2130 BIOS has it in board name.
Reported-by: Yuriy Zhuravlev <stalkerg@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The virtio-rng drivers checks for spurious callbacks. Since
callbacks can be implemented via shared interrupts (e.g. PCI) this
could lead to guest kernel oopses with lots of virtio devices.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (34 commits)
ACPI, i915: Register ACPI video even when not modesetting
Revert "ACPICA: delete check for AML access to port 0x81-83"
I/O port protection: update for windows compatibility.
sony-laptop: always try to unblock rfkill on load
sony-laptop: fix bogus error message display on resume
ACPI: EC: Fix ACPI EC resume non-query interrupt message
sony-laptop: SNC input event 38 fix
sony-laptop: SNC 127 Initialization Fix
sony-laptop: Duplicate SNC 127 Event Fix
ACPI: prevent processor.max_cstate=0 boot crash
ACPI/hpet: prevent boot hang when hpet=force used on ICH-4M
ACPI: delete obsolete "bus master activity" proc field
ACPI: idle: mark_tsc_unstable() at init-time, not run-time
ACPI: add /sys/firmware/acpi/interrupts/sci_not counter
ACPI video: fix an error when the brightness levels on AC and on Battery are same
acpi-cpufreq: Do not let get_measured perf depend on internal variable
acpi-cpufreq: style-only: add parens to math expression
acpi-cpufreq: Cleanup: Use printk_once
x86, acpi_cpufreq: Fix the NULL pointer dereference in get_measured_perf
thinkpad-acpi: bump up version to 0.23
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: pwc : do not pass stack allocated buffers to USB core.
USB: otg: Fix bug on remove path without transceiver
USB: correct error handling in cdc-wdm
USB: removal of tty->low_latency hack dating back to the old serial code
USB: serial: sierra driver bug fix for composite interface
USB: gadget: omap_udc uses platform_driver_probe()
USB: ci13xxx_udc: fix build error
USB: musb: Prevent multiple includes of musb.h
USB: pass mem_flags to dma_alloc_coherent
USB: g_file_storage: fix use-after-free bug when closing files
USB: ehci-sched.c: EHCI SITD scheduling bugfix
USB: fix mos7840 problem with minor numbers
USB: mos7840: add new device id
USB: musb: fix build when !CONFIG_PM
USB: musb: Remove my email address from few musb related drivers
USB: Gadget: MIPS CI13xxx UDC bugfixes
USB: Unusual Device support for Gold MP3 Player Energy
USB: serial: fix lifetime and locking problems
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Update defconfigs for 2.6.30-rc3
m68k,m68knommu: Wire up preadv and pwritev
scsi: a4000 - Correct driver unregistration in case of failure
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] update default configuration.
[S390] omit frame pointers on s390 when possible
[S390] Use tape_generic_offline directly.
[S390] /proc/stat idle field for idle cpus
[S390] appldata: avoid deadlock with appldata_mem
[S390] ipl: fix compile breakage
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
MAINTAINERS: update IDE entry
palm_bk3710: palm_bk3710_udmatimings[] CodingStyle fixup
palm_bk3710: those registers/bitfields don't exist
mediabay: fix build for CONFIG_BLOCK=n
ide: Stop disks on reboot for laptop which cuts power
ide-cd: fix kernel crash on hppa regression
palm_bk3710: UDMA performance fix
The release path for a disconnected device frees the object then unlocks
the mutex in the freed object...
Found by Dan Carpenter using Smatch
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove my name and emailaddress from note in the source. Wincor Nixdorf
only has some ITE-chips on their mainboards, other chips are not
available for me for testing.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cfq-iosched: cache prio_tree root in cfqq->p_root
cfq-iosched: fix bug with aliased request and cooperation detection
cfq-iosched: clear ->prio_trees[] on cfqd alloc
block: fix intermittent dm timeout based oops
umem: fix request_queue lock warning
block: simplify I/O stat accounting
pktcdvd.h should include mempool.h
cfq-iosched: use the default seek distance when there aren't enough seek samples
cfq-iosched: make seek_mean converge more quickly
block: make blk_abort_queue() ignore non-request based devices
block: include empty disks in /proc/diskstats
bio: use bio_kmalloc() in copy/map functions
bio: fix bio_kmalloc()
block: fix queue bounce limit setting
block: fix SG_IO vector request data length handling
scatterlist: make sure sg_miter_next() doesn't return 0 sized mappings
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (94 commits)
netfilter: ctnetlink: fix gcc warning during compilation
net/netrom: Fix socket locking
netlabel: Always remove the correct address selector
ucc_geth.c: Fix upsmr setting in RMII mode
8139too: fix HW initial flow
af_iucv: Fix race when queuing incoming iucv messages
af_iucv: Test additional sk states in iucv_sock_shutdown
af_iucv: Reject incoming msgs if RECV_SHUTDOWN is set
af_iucv: fix oops in iucv_sock_recvmsg() for MSG_PEEK flag
af_iucv: consider state IUCV_CLOSING when closing a socket
iwlwifi: DMA fixes
iwlwifi: add debugging for TX path
mwl8: fix build warning.
mac80211: fix alignment calculation bug
mac80211: do not print WARN if config interface
iwl3945: use cancel_delayed_work_sync to cancel rfkill_poll
iwlwifi: fix EEPROM validation mask to include OTP only devices
atmel: fix netdev ops conversion
pcnet_cs: add cis(firmware) of the Allied Telesis LA-PCM
mlx4_en: Fix cleanup if workqueue create in mlx4_en_add() fails
...
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix modular build of ide-pmac when mediabay is built in
powerpc/pasemi: Fix build error on UP
powerpc: Make macintosh/mediabay driver depend on CONFIG_BLOCK
maintainers: Fix PS3 patterns
powerpc/ps3: Fix CONFIG_PS3_FLASH=n build warning
powerpc/32: Don't clobber personality flags on exec
powerpc: Fix crash on CPU hotplug
powerpc/85xx: Remove defconfigs that mpc85xx_{smp_}defconfig cover
powerpc/85xx: Added SMP defconfig
powerpc/85xx: Enabled a bunch of FSL specific drivers/options
powerpc/85xx: Updated generic mpc85xx_defconfig
powerpc: don't disable SATA interrupts on Freescale MPC8610 HPCD
fsl_rio: Pass the proper device to dma mapping routines
powerpc: Fix of_node_put() exit path in of_irq_map_one()
powerpc/5200: defconfig updates
powerpc/5200: Add FLASH nodes to lite5200 device tree
powerpc/device-tree: Document MTD nodes with multiple "reg" tuples
powerpc/of-device-tree: Factor MTD physmap bindings out of booting-without-of
powerpc/5200: Bring the legacy fsl_spi_platform_data hooks back
The hash tables contains some of the mapping
so its really nice to have it for the deletion phase.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This line that checks the DRM_CONTROL_ALLOW flag was missed from the KMS
merge. Re-add the check on the IOCTL, as this is currently the only use of
this flag.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We have a drm_set_config which takes a crtc/encoder/mode setup,
and checks it to see if it can shortcut and just do a base setup,
or whether a complete mode setting is required.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We already added support, just need to let userspace
know when it can use them.
Signed-off-by: Maciej Cencora <m.cencora@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The ACPI video driver defers registration to the i915 driver if the
system supports opregion-mediated backlight control. This registration
was only being performed in the KMS case. Ensure it's done even if we
don't have modesetting enabled.
http://bugzilla.kernel.org/show_bug.cgi?id=13048
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit fdbdc7fc79.
That temporary quick-fix is no longer necessary,
as the previous patch, a65131e942,
"I/O port protection: update for windows compatibility"
should handle this issue for all ports, including this one.
Signed-off-by: Len Brown <len.brown@intel.com>
For windows compatibility,
1) On a port protection violation, simply ignore the request and
do not return an exception (allow the control method to continue execution.)
2) If only part of the request overlaps a protected port,
read/write the individual ports that are not protected.
http://bugzilla.kernel.org/show_bug.cgi?id=13036
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes an inconsistent behaviour when loading the driver with the
switch on or off. In the former case you would also need to soft unblock
the switch via the sysfs file entries to really disable rfkill, in the
latter you wouldn't.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Cc: Matthias Welwarsky <matze@welwarsky.de>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
sony_backlight_update_status returns 0 on success -1 on failure (i.e.: the
return value from acpi_callsetfunc. The return value in the resume path
was broken and thus always displaying a bogus warning about not being able
to restore the brightness level.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
When resuming from standby (on a laptop) I see the following message in
my kernel.log:
"ACPI: EC: non-query interrupt received, switching to interrupt mode"
This apparently prevented sony-laptop to properly restore the brightness
level on resume.
The cause: In drivers/acpi/ec.c the acpi_ec_suspend function clears the
GPE mode bit, but this is not restored in acpi_ec_resume (the function
below it). The patch below fixes this by properly restoring the GPE_MODE
bit. Tested and confirmed to work.
Signed-off-by: Almer S. Tigelaar <almer@gnome.org>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes the "unknown input event 38" messages. ANYBUTTON_RELEASED is now
treated the same way as FN_KEY_RELEASED.
Signed-off-by: Almer S. Tigelaar <almer@gnome.org>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes additional special key initialization for SNC 127 key events.
Verified / tested on a Sony VAIO SR model.
Signed-off-by: Almer S. Tigelaar <almer@gnome.org>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a duplicate mapping in the SNC sony_127_events structure.
Signed-off-by: Almer S. Tigelaar <almer@gnome.org>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
As processor.max_cstate is an init-time-only modparam,
sanity checking it at init-time is sufficient.
http://bugzilla.kernel.org/show_bug.cgi?id=13142
Signed-off-by: Len Brown <len.brown@intel.com>
This toshiba has a touchpad with trackpoint and 2 sets of left
and right buttons (above and below touchpad).
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Linux tells ICH4 users that they can (manually) invoke
"hpet=force" to enable the undocumented ICH-4M HPET.
The HPET becomes available for both clocksource and clockevents.
But as of ff69f2bba6
(acpi: fix of pmtimer overflow that make Cx states time incorrect)
the HPET may be used via clocksource for idle accounting, and
hpet=force on an ICH4 box hangs boot.
It turns out that touching the MMIO HPET withing
the ARB_DIS part of C3 will hang the hardware.
The fix is to simply move the timer access outside
the ARB_DIS region. This is a no-op on modern hardware
because ARB_DIS is no longer used.
http://bugzilla.kernel.org/show_bug.cgi?id=13087
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Symbols like SOFT_RESET are way too generic to be exported at large.
To avoid this, let's move the mbus bridge register defines into a
separate file and include it where needed. This affects mach-kirkwood,
mach-loki, mach-mv78xx0 and mach-orion5x simultaneously as they all
share code in plat-orion which relies on those defines.
Some other defines have been moved to narrower scopes, or simply deleted
when they had no user.
This fixes compilation problem with mpt2sas on the above listed
platforms.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Check if we really have Scoop config, otherwice we can get a nice Oops
during probe.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is causes problems on platforms that have alignment requirements
for DMA transfers.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the case where a gadget driver is removed while no
transceiver was found at probe time, a bug in
otg_put_transceiver() will trigger.
Provide symetric calls for otg_get_transceiver() and
otg_put_transceiver(), wherever a transceiver was found or
not.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch to cdc-wdm
- checks for partial extra descriptors
- fixes a leak in the error case of probe
- checks for an exact number of endpoints
- adds a clarifying comment
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pierre Ossman