Add efuse node for UniPhier LD11, LD20, and PXs3.
This efuse node is included in soc-glue.
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When HYP code runs into branch profiling code, it attempts to jump to
unmapped memory, causing a HYP Panic.
Disable the branch profiling for code designed to run at HYP mode.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
When a exception is trapped to EL2, hardware uses ELR_ELx to hold
the current fault instruction address. If KVM wants to inject a
abort to 32 bit guest, it needs to set the LR register for the
guest to emulate this abort happened in the guest. Because ARM32
architecture is pipelined execution, so the LR value has an offset to
the fault instruction address.
The offsets applied to Link value for exceptions as shown below,
which should be added for the ARM32 link register(LR).
Table taken from ARMv8 ARM DDI0487B-B, table G1-10:
Exception Offset, for PE state of:
A32 T32
Undefined Instruction +4 +2
Prefetch Abort +4 +4
Data Abort +8 +8
IRQ or FIQ +4 +4
[ Removed unused variables in inject_abt to avoid compile warnings.
-- Christoffer ]
Cc: <stable@vger.kernel.org>
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Tested-by: Haibin Zhang <zhanghaibin7@huawei.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Two fixes, one for the A31 DRM binding, and one for a missing regulator on
the pine MMC controller.
-----BEGIN PGP SIGNATURE-----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=Cvge
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Pull "Allwinner fixes for 4.14" from Maxime Ripard:
Two fixes, one for the A31 DRM binding, and one for a missing regulator on
the pine MMC controller.
* tag 'sunxi-fixes-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun6i: Fix endpoint IDs in second display pipeline
arm64: allwinner: a64: pine64: Use dcdc1 regulator for mmc0
Without the STDMAC clock enabled, the USB 2.0 hosts do not work.
This clock must be explicitly listed in the "clocks" property because
it is independent of the other clocks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The latest kernel tree already can support more MediaTek platforms such as
MT2712 and MT7622, so additional descriptions for those platforms are added
and certain cleanups are also being made here.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Since Salvator-X[S] have a USB2.0 dual-role channel (CN9), this patch
adds dr_mode property for USB2.0 channel 0 (EHCI/OHCI and HS-USB)
as "otg".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull "Rockchip dts64 updates for 4.15 part1" from Heiko Stübner:
The biggest step forward is probably the enablement of display support
on the rk3399-firefly, which got its default serial set as well and
got cec support as well.
Gru boards got their touchpad support refined to actually mark the button
correctly and also git their rt5514 dsp added.
And finally the rk3328 eval board got its cpu regulator and mmc nodes.
* tag 'v4.15-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: enable cec pin for rk3399 firefly
arm64: dts: rockchip: add the cec clk for dw-mipi-hdmi on rk3399
arm64: dts: rockchip: default serial for Firefly-RK3399
arm64: dts: rockchip: enable touchpad button for rk3399-gru-kevin
arm64: dts: rockchip: enable display subsystem on rk3399-firefly
arm64: dts: rockchip: Add rt5514 dsp for rk3399 gru
arm64: dts: rockchip: add cpu regulator for rk3328 evaluation board
arm64: dts: rockchip: add mmc nodes for rk3328 evaluation board
Pull "Qualcomm ARM64 Updates for v4.15" from Andy Gross:
* Add PCIE support to relevant MSM8996 based boards
* Add RPM clock controller node on MSM8996
* Add dload address on MSM8916 and MSM8996
* Add MBHC button support on APQ8016 SBC
* Add RTMFS specific compatible for rmtfs memory node
* Fixups for MSM8916 GPIO line names and MDP address length
* tag 'qcom-arm64-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: msm8916: Mark rmtfs node as qcom, rmtfs-mem compatible
arm64: dts: msm8996: Add the rpm clock controller node
arm64: dts: qcom: sbc: Name GPIO lines
arm64: dts: qcom: msm8916: Shrink mdp address length for msm8916
arm64: dts: apq8016-sbc: add mbhc buttons support
arm64: dts: qcom: Specify dload address for msm8916 and msm8996
arm64: dts: apq8096-db820c: never disable regulator on LS expansion
arm64: dts: apq8096-db820c: Enable on board 3 pcie root complex
arm64: dts: qcom: msm8996: add support to pcie
ARM64: DT: Hisilicon SoC DT updates for 4.15
- Add CoreSight related nodes for hi6220
- Add GPIO line names for hikey960
- Rectify the GPIO line names of the Poplar board to keep consistency
- Add thermal sensor binding doc and dt nodes for hi3660
* tag 'hisi-arm64-dt-for-4.15' of git://github.com/hisilicon/linux-hisi:
arm64: dts: Register Hi3660's thermal sensor
dt-bindings: Document the hi3660 thermal sensor binding
arm64: dts: hisilicon: Standardize Poplar GPIO line names
arm64: dts: hikey960: Update HiKey960 with GPIO line names
arm64: dts: hi6220: add coresight dt nodes
Pull "ARMv8 Vexpress/Juno DT update for v4.15" from Sudeep Holla:
Just single update to enable PSCI support on Foundation models
* tag 'juno-updates-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: foundation-v8: Enable PSCI mode
Pull "SoCFPGA DTS updates for v4.15" from Dinh Nguyen:
- Stratix10 platform updates
- Fix up gic register entry
- Enable ethernet/SDMMC
- Update reset manager properties
* tag 'socfpga_dts_for_v4.15_part1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: stratix10: add reset property for various peripherals
arm64: dts: stratix10: add the 'altr,modrst-off' property
arm64: dts: stratix10: include the reset manager bindings
arm64: dts: stratix10: add ethernet/sdmmc support to the S10 devkit
arm64: dts: stratix10: fix up the gic register for the Stratix10 platform
Pull "Renesas ARM64 Based SoC DT Updates for v4.15" from Simon Horman:
* r8a7795 (H3)
- Use r8a7795-cpg-mssr and r8a7795-sysc bindings
Hardcoded indicies are replaced with symbols now that they are available
- Drop bogus HDMI node name suffixes
Laurent Pinchart says: Node names should not use numerical suffixes if
the nodes can be distinguished by unit-address
- Update PFC node name to pin-controller
Shimoda-san says the PFC node name is changed "from e6060000.pfc and
pfc@e6060000 to e6060000.pin-controller and pin-controller@e6060000
like other Renesas SoCs."
* r8a7795 (H3) ES1.0
- Drop extra zero from XHCI unit address
This corrects a typo were ee0400000 rather than ee040000 was used
as the unit address.
* r8a7796 (M3-W)
- Add FDP1 instance
Laurent Pinchart says: The r8a7796 has a single FDP1 instance.
* r8a7795 (H3) and r8a7796 (M3-W) SoCs
- Add USB3.0 peripheral device nodes
Shimoda-san says that this is not enabled on the Salvator-X/XS boards
for now as:
+ we need a special cable (USB type-A to A cross cable).
+ we can swap the role by renesas_usb3 driver even if we use a normal
cable and after usb3.0 host is running, but I think it's a special
use case.
* r8a7795 (H3) and r8a7796 (M3-W) ULCB boards
- Enable display output
Laurent Pinchart says: The DU is already wired up to the HDMI encoder,
all we need to do is enable it.
* r8a77995 (D3) Draak board
- Enable EthernetAVB and , USB2.0 Host and PHY
- Add serial console pins.
This is safe to do now that r8a77995 PFC driver support is present
* r8a77970 (V3M)
- Add basic support for SoC and EtherAVB, [H]SCIF and SYS-DMAC nodes
This is a step towards enabling EtherAVB and [H]SCIF with SYS-DMAC
in the Eagle board support for which is under review
* tag 'renesas-arm64-dt-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (22 commits)
arm64: dts: renesas: r8a7796: add USB3.0 peripheral device node
arm64: dts: renesas: r8a7795: add USB3.0 peripheral device node
arm64: dts: renesas: r8a77995: draak: enable EthernetAVB
arm64: dts: renesas: r8a77995: draak: enable USB2.0 Host (EHCI/OHCI)
arm64: dts: renesas: r8a77995: draak: enable USB2.0 PHY
arm64: dts: renesas: r8a77995: add USB2.0 Host (EHCI/OHCI) device node
arm64: dts: renesas: r8a77995: Add USB2.0 PHY device node
arm64: dts: draak: Add serial console pins
arm64: dts: renesas: r8a77970: add EtherAVB support
arm64: dts: renesas: r8a77970: add [H]SCIF support
arm64: dts: renesas: r8a77970: add SYS-DMAC support
arm64: dts: renesas: initial R8A77970 SoC device tree
arm64: dts: renesas: r8a77995: Add EthernetAVB device node
arm64: dts: renesas: r8a77995: add GPIO device nodes
arm64: dts: renesas: r8a77995: Use r8a7795-cpg-mssr binding definitions
arm64: dts: renesas: r8a77995: Use r8a7795-sysc binding definitions
arm64: renesas: Add Renesas R8A77970 Kconfig support
arm64: dts: renesas: r8a7795: Drop bogus HDMI node names suffixes
arm64: dts: renesas: ulcb: Enable display output
arm64: dts: renesas: r8a77995: update PFC node name to pin-controller
...
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm64/boot/dts -type -f -name '*.dts*'
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable QCOM IOMMU driver for 'B' family devices, such as APQ8016 found on the
Dragonboard 410c. With this change, graphics console and GPU are working
fine (using mesa/freedreno for GPU driver).
Signed-off-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ThunderX needs its PCI host drivers to do anything useful, and
it's probably helpful to have networking by default too.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that the ARM ARM clearly specifies the rules for inferring
the values of the ID register fields, fix the types of the
feature bits we have in the kernel.
As per ARM ARM DDI0487B.b, section D10.1.4 "Principles of the
ID scheme for fields in ID registers" lists the registers to
which the scheme applies along with the exceptions.
This patch changes the relevant feature bits from FTR_EXACT
to FTR_LOWER_SAFE to select the safer value. This will enable
an older kernel running on a new CPU detect the safer option
rather than completely disabling the feature.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Martin <dave.martin@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
* Enable the following to allow further test coverage
- r8a77970 (V3M) and r8a77995 (D3) R-Car Gen3 SoCs
- R-Car Gen3 thermal driver.
This is used on a range of R-Car Gen3 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nZqA
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-defconfig-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Pull "Renesas ARM64 Based SoC Defconfig Updates for v4.15" from Simon Horman:
* Enable the following to allow further test coverage
- r8a77970 (V3M) and r8a77995 (D3) R-Car Gen3 SoCs
- R-Car Gen3 thermal driver.
This is used on a range of R-Car Gen3 SoCs
* tag 'renesas-arm64-defconfig-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: defconfig: enable R8A77970 SoC
arm64: defconfig: enable thermal driver for Renesas R-Car Gen3
arm64: defconfig: Enable Renesas R8A77995 SoC
Add 12V regulator to backlight allowing the power supply
for the backlight to be found.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zIL3
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Pull "Renesas ARM Based SoC Fixes for v4.14" from Simon Horman:
Add 12V regulator to backlight allowing the power supply
for the backlight to be found.
* tag 'renesas-fixes-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: salvator-common: add 12V regulator to backlight
exceed 3.0V, so they got fixed to not be at 3.3V
And Arnd found a typo in the recently added iommu nodes.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlnmSIIQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgeaQB/9JDBD545VzXqsNixEnJOcT+X8sUZpu6OmT
j3v5kJDPOXLfSP/Ci9S10ldix/JUBZoT2fRJCK5QAzo+NnjYWrC5qPAwGVU90TqY
KxFZu4f1763AU2ZLw9nGJlFeVHrjhpFdYfe9GpPPLmndjM32cRdGCRI5zDaSB7s8
popUs6qNGvI5Q770x4/xTfEqDlfdQhmYyNfWumji7ACfLTHYZnpyq0SN/o4qp/rg
UJaPx/7PGzHIDSrEKRE3i+waG3d7Ix4th9jkmrYFAK2nIiySlZg9WIKWEOqqt+sf
H8W3ygdlaYZlzIPJhY2r6/W1rQoJSLxxKColLrV32hDkjPfcFon5
=YPhS
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-dts64fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts64 Fixes for 4.14 part 2" from Heiko Stübner:
The vqmmc voltages on rk3399 pose a risk for the chip if they
exceed 3.0V, so they got fixed to not be at 3.3V
And Arnd found a typo in the recently added iommu nodes.
* tag 'v4.14-rockchip-dts64fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: fix typo in iommu nodes
arm64: dts: rockchip: correct vqmmc voltage for rk3399 platforms
Two device tree related fixes:
- One on Armada 38x using a other compatible string for I2C in order
to cover an errata.
- One for Armada 7K/8K fixing a typo on interrupt-map property for
PCIe leading to fail PME and AER root port service initialization
And the last one for the mbus fixing the window size calculation when
it exceed 32bits
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWeDbriMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71RAJAJ9TyT+GrMdf
HsM7V74bSWYAUlWZ0ACcCWjIdnbVlinP+iuVS462du4HpU0=
=2AQR
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.14-2' of git://git.infradead.org/linux-mvebu into fixes
Pull "mvebu fixes for 4.14 (part 2)" from Gregory CLEMENT
Two device tree related fixes:
- One on Armada 38x using a other compatible string for I2C in order
to cover an errata.
- One for Armada 7K/8K fixing a typo on interrupt-map property for
PCIe leading to fail PME and AER root port service initialization
And the last one for the mbus fixing the window size calculation when
it exceed 32bits
* tag 'mvebu-fixes-4.14-2' of git://git.infradead.org/linux-mvebu:
bus: mbus: fix window size calculation for 4GB windows
ARM: dts: Fix I2C repeated start issue on Armada-38x
arm64: dts: marvell: fix interrupt-map property for Armada CP110 PCIe controller
This adds the thermal sensor device provided by the BPMP, and the
relevant thermal sensors to the Tegra186 device tree.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 has three PCIe controllers, which can be operated
in 401, 211 or 111 lane combinations. Add DT support for
PCIe controllers.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a node for the Video Image Compositor on the Tegra186.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the node for Host1x on the Tegra186, without any subdevices
for now.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add #power-domain-cells for the BPMP node on Tegra186 so that the power
domain provider may be used.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ITSes on the Hip07 (as present in the Huawei D05) are broken when
it comes to addressing the redistributors, and need to be explicitely
told to address the VLPI page instead of the redistributor base address.
So let's add yet another quirk, fixing up the target address
in the command stream.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Socionext Synquacer SoC's implementation of GICv3 has a so-called
'pre-ITS', which maps 32-bit writes targeted at a separate window of
size '4 << device_id_bits' onto writes to GITS_TRANSLATER with device
ID taken from bits [device_id_bits + 1:2] of the window offset.
Writes that target GITS_TRANSLATER directly are reported as originating
from device ID #0.
So add a workaround for this. Given that this breaks isolation, clear
the IRQ_DOMAIN_FLAG_MSI_REMAP flag as well.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A new feature Range Selector (RS) has been added to GIC specification
in order to support more than 16 CPUs at affinity level 0. New fields
are introduced in SGI system registers (ICC_SGI0R_EL1, ICC_SGI1R_EL1
and ICC_ASGI1R_EL1) to relax an artificial limit of 16 at level 0.
- A new RSS field in ICC_CTLR_EL3, ICC_CTLR_EL1 and ICV_CTLR_EL1:
[18] - Range Selector Support (RSS)
0b0 = Targeted SGIs with affinity level 0 values of 0-15 are supported.
0b1 = Targeted SGIs with affinity level 0 values of 0-255 are supported.
- A new RS field in ICC_SGI0R_EL1, ICC_SGI1R_EL1 and ICC_ASGI1R_EL1:
[47:44] - RangeSelector (RS) which group of 16 TargetList[n] field
TargetList[n] represents aff0 value ((RS*16)+n)
When ICC_CTLR_EL3.RSS==0 or ICC_CTLR_EL1.RSS==0, RS is RES0.
- A new RSS field in GICD_TYPER:
[26] - Range Selector Support (RSS)
0b0 = Targeted SGIs with affinity level 0 values of 0-15 are supported.
0b1 = Targeted SGIs with affinity level 0 values of 0-255 are supported.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Try to add basic DT support for the Amlogic's Meson-AXG A113D SoC,
which describe components as follows: Reserve Memory, CPU, GIC, IRQ,
Timer, UART. It's capable of booting up into the serial console.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Based on: ARM Architecture Reference Manual, ARMv8 (DDI 0487B.b).
ARMv8.1 introduces the optional feature ARMv8.1-TTHM which can trigger a
new type of memory abort. This exception is triggered when hardware update
of page table flags is not atomic in regards to other memory accesses.
Replace the corresponding unknown entry with a more accurate one.
Cf: Section D10.2.28 ESR_ELx, Exception Syndrome Register (p D10-2381),
section D4.4.11 Restriction on memory types for hardware updates on page
tables (p D4-2116 - D4-2117).
ARMv8.2 does not add new exception types, however it is worth mentioning
that when obligatory feature RAS (optional for ARMv8.{0,1}) is implemented,
exceptions related to "Synchronous parity or ECC error on memory access,
not on translation table walk" become reserved and should not occur.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The driver has supported the 64-bit Tegra210 for a while now, so enable
it in the defconfig.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When booting at EL2, ensure that we permit the EL1 host to sample
physical addresses and physical counter values using SPE.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
SPE is part of the v8.2 architecture, so move its system register and
field definitions into sysreg.h and the new PSB barrier into barrier.h
Finally, move KVM over to using the generic definitions so that it
doesn't have to open-code its own versions.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The latest dtc warns about an extraneous cell in the interrupt
property of two of the iommu device nodes:
Warning (interrupts_property): interrupts size is (16), expected multiple of 12 in /iommu@ff373f00
Warning (interrupts_property): interrupts size is (16), expected multiple of 12 in /iommu@ff900800
This removes the typo.
Fixes: cede4c79de ("arm64: dts: rockchip: add rk3368 iommu nodes")
Fixes: 49c82f2b7c ("arm64: dts: rockchip: add rk3328 iommu nodes")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The vcc_sd or vcc_sdio used for IO voltage for sdmmc and sdio
interface on rk3399 platform have a limitation that it can't be
larger than 3.0v, otherwise it has a potential risk for the chip.
Correct all of them.
Fixes: 171582e00d ("arm64: dts: rockchip: add support for firefly-rk3399 board")
Fixes: 2c66fc34e9 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Fixes: 8164a84cca ("arm64: dts: rockchip: Add support for rk3399 sapphire SOM")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Stephen Boyd reworked some Qualcomm USB code earlier this year.
The result requires a few different config options to be enabled
in order for the USB on the DragonBoard 410c to continue working,
but these were never added to arm64 "defconfig". As a result, USB
on that board stopped working during the v4.13-rc1 merge window.
Re-enable this functionality by setting the needed config options
in the arm64 "defconfig" file.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Use newly added R-Car GPIO Gen3 fallback compat string
in place of now deprecated non-generation specific
R-Car GPIO fallback compat string in the DT of the r8a7796 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use newly added R-Car GPIO Gen3 fallback compat string
in place of now deprecated non-generation specific
R-Car GPIO fallback compat string in the DT of the r8a7795 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
"audio_clkout" is dummy clock of <&rcar_sound 0> to avoid clock loop
which invites probe conflict. Thus <&rcar_sound 0> and "audio_clkout"
should be same value.
On commit 2752660a37 ("arm64: dts: renesas: ulcb: sound
clock-frequency needs descending order") exchanged <&rcar_sound 0>,
but it didn't modify "audio_clkout".
This patch fixup it.
Fixes: 2752660a37 ("arm64: dts: renesas: ulcb: sound clock-frequency needs descending order")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
"audio_clkout" is dummy clock of <&rcar_sound 0> to avoid clock loop
which invites probe conflict. Thus <&rcar_sound 0> and "audio_clkout"
should be same value.
On commit 5e2feac330 ("arm64: renesas: salvator-common: sound
clock-frequency needs descending order") exchanged <&rcar_sound 0>,
but it didn't modify "audio_clkout".
This patch fixup it.
Fixes: 5e2feac330 ("arm64: renesas: salvator-common: sound clock-frequency needs descending order")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a Device Tree for the PROBOX2 AVA TV Box.
Move common memory reservations into rtd1295.dtsi.
Cc: support@probox2.com
Signed-off-by: Andreas Färber <afaerber@suse.de>
Add a pinctrl setting to configure the cec pin to the correct function.
Signed-off-by: Pierre-Hugues Husson <phh@phh.me>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the HDMI CEC controller main clock coming from the CRU.
Signed-off-by: Pierre-Hugues Husson <phh@phh.me>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add nodes of thermal monitor and thermal zone for UniPhier LD20 SoC.
The thermal monitor node is included in sysctrl. Since the efuse might not
have a calibrated value of thermal monitor, this patch gives the default
value for LD20.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Firefly-RK3399 uses serial2 with 1,500,000 baud by default
for communication in U-Boot and in the vendor provided distros.
So let us set the same default in the Linux kernel.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Adding the linux,gpio-keymap entry also has
the side-effect of making the driver register
the touchpad as a touchpad rather than another
touchscreen.
The index for BTN_LEFT was found by trial and error.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The current delay implementation uses the yield instruction, which is a
hint that it is beneficial to schedule another thread. As this is a hint,
it may be implemented as a NOP, causing all delays to be busy loops. This
is the case for many existing CPUs.
Taking advantage of the generic timer sending periodic events to all
cores, we can use WFE during delays to reduce power consumption. This is
beneficial only for delays longer than the period of the timer event
stream.
If timer event stream is not enabled, delays will behave as yield/busy
loops.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The arch timer configuration for a CPU might get reset after suspending
said CPU.
In order to reliably use the event stream in the kernel (e.g. for delays),
we keep track of the state where we can safely consider the event stream as
properly configured. After writing to cntkctl, we issue an ISB to ensure
that subsequent delay loops can rely on the event stream being enabled.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The SD card slot connected to the SD controller of the CP part has a
carrier detect pin connected the gpio expander. This patch enables it
allowing supporting the hotplug event for the SD card.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 38x RTC driver supports also the RTC controller found on the
Armada 7K/8K SoCs, so enable it.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch fixes some spelling typos found in Kconfig files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that we have a binding defined for the shared file system memory use
this to describe the rmtfs memory region.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This names the GPIO lines on the APQ8016 "SBC" also known
as the DragonBoard 410c, according to the schematic. This
is necessary for a conforming userspace looking across
all GPIO chips for the GPIO lines named "GPIO-A" thru
"GPIO-L".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This shrinks the address size down to 89000 from its previous 90000
which was mistakenly pulled from downstream.
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
On msm8916 and msm8996 boards a secure io-write is used to write the
magic for selecting "download mode", specify this address in the
DeviceTree.
Note that qcom_scm.download_mode=1 must be specified on the kernel
command line for the kernel to attempt selecting download mode.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
1.8v regulator on LS expansion should not be disabled anytime to comply
with 96boards spec. So make this explicit with always-on flag.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Since the switch to documented uart bindings, the old undocumented
compatible binding was left for simplicity.
This patch removes these unneeded compatible strings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Since the switch to documented uart bindings, the clocks are
redefined in the SoC family dtsi file.
This patch removes these unneeded properties.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This year, Amlogic updated the ARM Trusted Firmware reserved memory mapping
for Meson GXL SoCs and products sold since May 2017 uses this alternate
reserved memory mapping.
But products had been sold using the previous mapping.
This issue has been explained in [1] and a dynamic solution is yet to be
found to avoid loosing another 3Mbytes of reservable memory.
In the meantime, this patch adds this alternate memory zone only for
the GXL and GXM SoCs since GXBB based new products stopped earlier.
[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html
Fixes: bba8e3f427 ("ARM64: dts: meson-gx: Add firmware reserved memory zones")
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable HS400 high speed eMMC mode on the khadas vim2
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable both gxbb USB controllers and add a 5V regulator for the OTG port
VBUS, similar to p20x.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Tronsmart Vega S96 is a TV box derived from Amlogic q200 reference design.
Cc: support@tronsmart.com
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Oleg Ivanov <balbes-150@yandex.ru>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Khadas VIM2 is a Single Board Computer, respin of the origin
Khadas VIM board, using an Amlogic S912 SoC and more server oriented.
It provides the same external connectors and header pinout, plus a SPI
NOR Flash, a reprogrammable STM8S003 MCU, FPC Connector, Cooling FAN header
and Pogo Pads Arrays.
Cc: Gouwa <gouwa@szwesion.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Since the Data Strobe pin is optional, take it out of the default
eMMC pins and add a separate entry.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
TEST_N gpio has been moved so the gpio-line-names of the cc
must be adjusted accordingly
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
TEST_N gpio has been moved so the gpio-line-names of the kvim
must be adjusted accordingly
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
GPIOX22 is now declared properly and TEST_N has been moved so
the gpio-line-names of the odroid-c2 must be adjusted accordingly
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
GPIOX22 is now declared properly and TEST_N has been moved so
the gpio-line-names of the nanopi-k2 must be adjusted accordingly
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
TEST_N has moved from the EE controller to the AO controller so
the gpio-ranges need to adjusted for it
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Remove pin offset on the EE controller. Meson pinctrl no longer has
this quirk
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the internal phy ACT and LINK leds pinmux
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable saradc and add the reference 1.8v regulator required.
The libretech-cc has saradc channel 0 and 2 available on the 2 first
pins of 2J3 header
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable QCOM IOMMU driver for 'B' family devices, such as APQ8016 found on the
Dragonboard 410c. With this change, graphics console and GPU are working
fine (using mesa/freedreno for GPU driver).
Signed-off-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds enables 3 instances of root complexes which are
exposed on DB820c board. 3 Instances are terminted as below
PCIE0 => QCA6174
PCIE1 => MINI PCIE CARD
PCIE2 => GBE ETHERNET
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to 3 pcie root complexes found on MSM8996.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
ARMv8-A adds a few optional features for ARMv8.2 and ARMv8.3.
Expose them to the userspace via HWCAPs and mrs emulation.
SHA2-512 - Instruction support for SHA512 Hash algorithm (e.g SHA512H,
SHA512H2, SHA512U0, SHA512SU1)
SHA3 - SHA3 crypto instructions (EOR3, RAX1, XAR, BCAX).
SM3 - Instruction support for Chinese cryptography algorithm SM3
SM4 - Instruction support for Chinese cryptography algorithm SM4
DP - Dot Product instructions (UDOT, SDOT).
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Dave Martin <dave.martin@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add binding for tsensor on H3660, this tsensor is used for
SoC thermal control, it supports alarm interrupt.
Signed-off-by: Kevin Wangtao <kevin.wangtao@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add CPU idle state nodes to enable C1/C2 idle states.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The hi6220-HiKey board started to name GPIO lines for
96boards, using just the plain names "GPIO-A" etc from the
96boards specification.
Poplar started to use an arbitrary "LS-GPIO-A" (etc) prefix
that is not part of the 96boards specification.
As the former notation arrived first, and we need
consistency among 96board, rectify the Poplar board to use
this too. This is important for userspace that wants to
look up GPIO names from these strings.
Cc: Jiancheng Xue <xuejiancheng@hisilicon.com>
Cc: Alex Elder <elder@linaro.org>
Cc: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This adds line names for all the GPIOs I could identify on the HiKey960
schematic.
"GPIO-A" through "GPIO-L" are the most important since they give users
a handle to look up the standard 96boards GPIOs from the GPIO character
device.
The rest of the names are more informational, nice debug information
for "lsgpio" so you can see that the right line is taken for the right
function in the kernel for example.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Zhangfei Gao <zhangfei.gao@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
For detailed coresight topology, Hi6220 has 8xCA53 CPUs and each CPU
has one Embedded Trace Macrocell (ETM); the CPU trace data is output
to the cluster funnel. Due system has another CPU and one MCU, all of
them transfer the trace data through trace bus (ATB) to SoC funnel;
the SoC funnel is connected to Embedded Trace FIFO (ETF) with 8KB
buffer; an non-configurable replicator is used to output trace data
for two sinks, one is Embedded Trace Route (ETR) so trace data can be
saved into DRAM, another is Trace Port Interface Unit (TPIU) for
capturing trace data by external debugger.
According to the Hi6220 coresight topology, this patch is to add
coresight dt nodes.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Li Pengcheng <lipengcheng8@huawei.com>
Signed-off-by: Li Zhong <lizhong11@hisilicon.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The arch_{read,spin,write}_lock_flags() macros are simply mapped to the
non-flags versions by the majority of architectures, so do this in core
code and remove the dummy implementations. Also remove the implementation
in spinlock_up.h, since all callers of do_raw_spin_lock_flags() call
local_irq_save(flags) anyway.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: paulmck@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/1507055129-12300-4-git-send-email-will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
arch_{read,spin,write}_relax() are defined as cpu_relax() by the core
code, so architectures that can't do better (i.e. most of them) don't
need to bother with the dummy definitions.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: paulmck@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/1507055129-12300-3-git-send-email-will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Define the Eagle board dependent part of the EtherAVB device node.
Enable DHCP and NFS root for the kernel booting.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Interrupt Controller for External Devices
(INTC-EX) on R-Car D3, which serves external IRQ pins IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Interrupt Controller for External Devices
(INTC-EX) on R-Car V3M, which serves external IRQ pins IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Interrupt Controller for External Devices
(INTC-EX) on R-Car M3-W, which serves external IRQ pins IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds gpio hogs for USB3 hub on ULCB Kingfisher board to power up and
remove from reset the hub
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports PCA9548 I2C switch on I2C4 bus on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports PCA9548 I2C switch on I2C2 bus on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports TCA9539 gpio expanders on I2C4 bus on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports TCA9539 gpio expanders on I2C2 bus on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports USB3.0 Host on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports PCIE0/1 on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports HSUSB on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports CAN0/1 on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports SCIF1 on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the H3ULCB ES2.0+ SoC with Kingfisher
extension infotainment board.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the H3ULCB ES1.x SoC with Kingfisher
extension infotainment board.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the M3ULCB with Kingfisher extension
infotainment board.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial common dtsi file for Kingfisher infotainment board (R-Car
Starter Kit extension)
This commit supports the following peripherals:
- HSCIF0
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables PWM channel 0 and 1 on the draak. Each channel
connects to LTC2644 for brightness control.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since a R-Car Gen3 bootloader enables the PFC of USB3.0 channel 0,
the USB3.0 host controller works without this setting on the kernel.
But, this setting should have salvator-common.dtsi. So, this patch
adds the pfc node for USB3.0 channel 0.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Process personality always propagates across a fork(), but can change
at an execve().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- Bring initialisation of user space undefined instruction handling
early (core_initcall) since late_initcall() happens after modprobe in
initramfs is invoked. Similar fix for fpsimd initialisation
- Increase the kernel stack when KASAN is enabled
- Bring the PCI ACS enabling earlier via the
iort_init_platform_devices()
- Fix misleading data abort address printing (decimal vs hex)
-----BEGIN PGP SIGNATURE-----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=Iu63
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Bring initialisation of user space undefined instruction handling
early (core_initcall) since late_initcall() happens after modprobe in
initramfs is invoked. Similar fix for fpsimd initialisation
- Increase the kernel stack when KASAN is enabled
- Bring the PCI ACS enabling earlier via the
iort_init_platform_devices()
- Fix misleading data abort address printing (decimal vs hex)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Ensure fpsimd support is ready before userspace is active
arm64: Ensure the instruction emulation is ready for userspace
arm64: Use larger stacks when KASAN is selected
ACPI/IORT: Fix PCI ACS enablement
arm64: fix misleading data abort decoding
We register the pm/hotplug callbacks for FPSIMD as late_initcall,
which happens after the userspace is active (from initramfs via
populate_rootfs, a rootfs_initcall). Make sure we are ready even
before the userspace could potentially use it, by promoting to
a core_initcall.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Dave Martin <dave.martin@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We trap and emulate some instructions (e.g, mrs, deprecated instructions)
for the userspace. However the handlers for these are registered as
late_initcalls and the userspace could be up and running from the initramfs
by that time (with populate_rootfs, which is a rootfs_initcall()). This
could cause problems for the early applications ending up in failure
like :
[ 11.152061] modprobe[93]: undefined instruction: pc=0000ffff8ca48ff4
This patch promotes the specific calls to core_initcalls, which are
guaranteed to be completed before we hit userspace.
Cc: stable@vger.kernel.org
Cc: Dave Martin <dave.martin@arm.com>
Cc: Matthias Brugger <mbrugger@suse.com>
Cc: James Morse <james.morse@arm.com>
Reported-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add the initial device tree for the R8A77970 SoC based Eagle board.
The board has 1 debug serial port (SCIF0); include support for it,
so that the serial console can work.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
AddressSanitizer instrumentation can significantly bloat the stack, and
with GCC 7 this can result in stack overflows at boot time in some
configurations.
We can avoid this by doubling our stack size when KASAN is in use, as is
already done on x86 (and has been since KASAN was introduced).
Regardless of other patches to decrease KASAN's stack utilization,
kernels built with KASAN will always require more stack space than those
built without, and we should take this into account.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
For example on arm64 board, this add info to "user" entries in vmallocinfo
Before :
[...]
0xffffff8008997000 0xffffff80089d8000 266240 user
[...]
Afer :
[...]
0xffffff8008997000 0xffffff80089d8000 266240 atomic_pool_init+0x0/0x1d8 user
[...]
This help to debug mapping issues, and is consistent with others entries
(ioremap, vmalloc, ...) that already provide caller.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
From what I can see there isn't anything about ACPI_APEI_SEA that
means the arm64 architecture can or cannot support NMI safe
cmpxchg or NMIs, so the 'if' condition here is not important.
Let's remove it. Doing that allows us to support ftrace
histograms via CONFIG_HIST_TRIGGERS that depends on the arch
having the ARCH_HAVE_NMI_SAFE_CMPXCHG config selected.
Cc: Tyler Baicar <tbaicar@codeaurora.org>
Cc: Jonathan (Zhixiong) Zhang <zjzhang@codeaurora.org>
Cc: Dongjiu Geng <gengdongjiu@huawei.com>
Acked-by: James Morse <james.morse@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently we inconsistently log identifying information for the boot CPU
and secondary CPUs. For the boot CPU, we log the MIDR and MPIDR across
separate messages, whereas for the secondary CPUs we only log the MIDR.
In some cases, it would be useful to know the MPIDR of secondary CPUs,
and it would be nice for these messages to be consistent.
This patch ensures that in the primary and secondary boot paths, we log
both the MPIDR and MIDR in a single message, with a consistent format.
the MPIDR is consistently padded to 10 hex characters to cover Aff3 in
bits 39:32, so that IDs can be compared easily.
The newly redundant message in setup_arch() is removed.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Al Stone <ahs3@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
[will: added '0x' prefixes consistently]
Signed-off-by: Will Deacon <will.deacon@arm.com>
for the boards as all of them are missing their cpu supplies, the OPPs
actually need to follow the <target min max> format as the regulator is
shared between both clusters and the one rk3368 board I have, somehow also
doesn't like the higher opps at all - all of which I only realized after
I brought my rk3368 board online again, after its bootloader broke.
So we revert that OPP addition for now.
And also two fixes for the mipi dsi controller on rk3399, which was
referencing a clock to high up in the clock-tree so that an intermediate
gate could be disabled inadvertently and also needs a clock for its area
in the general register files of the rk3399 soc.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlnL6QsQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgUx1B/4pbbWGvxKA/1Osih4Fs/q8rLzNq9N8tsV1
VEQ06VU0TuuyECiNhCv1sD8QoccdAfAu/QlFM2IVg3Js2HB+CtnYw0LVhMEpdf0m
c4Vh/GgpCIgPTaZTDtcHdHh9VbbYDsgsVgLPiuBnbK98GeDVZCIke10J0cUBrwSY
ncJKFfJQh1wor9p54mQfBWtKWfUfDQYxBpENkwq1SD0TJgE/osyKevWXConjMN1f
vyH+BmEJq96Wz76QqEXtiEU47HoHaIMwA7/2LbRJhe5W3ifBFBQD664RH6L/a28o
IhRTq3pvy4v7lip4OTRMby4+C6Yku7Xb3UF3/HAKPntE5eKlpIjV
=DwOn
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-dts64fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Adding the operating points on rk3368 like they were did not end up well
for the boards as all of them are missing their cpu supplies, the OPPs
actually need to follow the <target min max> format as the regulator is
shared between both clusters and the one rk3368 board I have, somehow also
doesn't like the higher opps at all - all of which I only realized after
I brought my rk3368 board online again, after its bootloader broke.
So we revert that OPP addition for now.
And also two fixes for the mipi dsi controller on rk3399, which was
referencing a clock to high up in the clock-tree so that an intermediate
gate could be disabled inadvertently and also needs a clock for its area
in the general register files of the rk3399 soc.
* tag 'v4.14-rockchip-dts64fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399
arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399
Revert "arm64: dts: rockchip: Add basic cpu frequencies for RK3368"
Signed-off-by: Olof Johansson <olof@lixom.net>
Update MAINTAINERS for the Macchiatobin board (Armada 8K based)
Fix AP806 system controller size on Armada 7K/8K
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWcTR4CMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71ZOIAJ0Wh05lcRfe
0wugR0R319wn9gD5HwCfURWc08Qvo97ZdGp38wQaAuNnJfw=
=5jLY
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.14-1' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.14 (part 1)
Update MAINTAINERS for the Macchiatobin board (Armada 8K based)
Fix AP806 system controller size on Armada 7K/8K
* tag 'mvebu-fixes-4.14-1' of git://git.infradead.org/linux-mvebu:
arm64: dt marvell: Fix AP806 system controller size
MAINTAINERS: add Macchiatobin maintainers entry
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently if the Foundation model is running ARM Trusted Firmware then
the kernel, which is configured to use spin tables, cannot start secondary
processors or "power off" the simulation.
After adding a couple of labels to the include file and splitting out the
spin-table configuration into a header, we add a couple of new headers
together with two new DTs (GICv2 + PSCI and GICv3 + PSCI).
The new GICv3+PSCI DT has been boot tested, the remaining three (two of
which existed prior to this patch) have been "tested" by decompiling the
blobs and comparing them against a reference.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Since the Ethernet AVB driver doesn't support AVB_PHY_INT handling
and it will be handled by a phy driver as a gpio pin, this patch
removes the "avb_phy_int" from the avb_pins node.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Fixes: 4503b50eac ("arm64: dts: renesas: r8a77995: draak: enable EthernetAVB")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the Ethernet AVB driver doesn't support AVB_PHY_INT handling
and it will be handled by a phy driver as a gpio pin, this patch
removes the "avb_phy_int" from the avb_pins node.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 133ace3f38 ("arm64: dts: ulcb: Set drive-strength for ravb pins")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the Ethernet AVB driver doesn't support AVB_PHY_INT handling
and it will be handled by a phy driver as a gpio pin, this patch
removes the "avb_phy_int" from the avb_pins node.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 7d73a4da26 ("arm64: dts: r8a7795: salvator-x: Set drive-strength for ravb pins")
Fixes: 4903987033be ("arm64: dts: r8a7796: salvator-x: Set drive-strength for ravb pins")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 8cd5601c50 ("sched/fair: Convert arch_scale_cpu_capacity() from
weak function to #define") changed the wiring which now has to be done
by associating arch_scale_cpu_capacity with the actual implementation
provided by the architecture.
Define arch_scale_cpu_capacity to use the arch_topology "driver"
function topology_get_cpu_scale() for the task scheduler's cpu-invariant
accounting instead of the default arch_scale_cpu_capacity() in
kernel/sched/sched.h.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Tested-by: Juri Lelli <juri.lelli@arm.com>
Reviewed-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit dfbca41f34 ("sched: Optimize freq invariant accounting")
changed the wiring which now has to be done by associating
arch_scale_freq_capacity with the actual implementation provided
by the architecture.
Define arch_scale_freq_capacity to use the arch_topology "driver"
function topology_get_freq_scale() for the task scheduler's
frequency-invariant accounting instead of the default
arch_scale_freq_capacity() in kernel/sched/sched.h.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Tested-by: Juri Lelli <juri.lelli@arm.com>
Reviewed-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Armada 8040 DB has numerous PCIe ports, so let's enable a few more
of those PCIe ports that are enabled in the default bootloader
configuration.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Currently data_abort_decode() dumps the ISS field as a decimal value
with a '0x' prefix, which is somewhat misleading.
Fix it to print as hexadecimal, as was intended.
Fixes: 1f9b8936f3 ("arm64: Decode information from ESR upon mem faults")
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The interrupt-map property used in the description of the Marvell
Armada 7K/8K PCIe controllers has a bogus extraneous 0 that causes the
interrupt conversion to not be done properly. This causes the PCIe PME
and AER root port service drivers to fail their initialization:
[ 5.019900] genirq: Setting trigger mode 7 for irq 114 failed (irq_chip_set_type_parent+0x0/0x30)
[ 5.028821] pcie_pme: probe of 0001:00:00.0:pcie001 failed with error -22
[ 5.035687] genirq: Setting trigger mode 7 for irq 114 failed (irq_chip_set_type_parent+0x0/0x30)
[ 5.044614] aer: probe of 0001:00:00.0:pcie002 failed with error -22
This problem was introduced when the interrupt description was
switched from using the GIC directly to using the ICU interrupt
controller. Indeed, the GIC has address-cells = <1>, which requires a
parent unit address, while the ICU has address-cells = <0>.
Fixes: 6ef84a827c ("arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As discussed at the Linux Security Summit, arm64 prefers to use
REFCOUNT_FULL by default. This enables it for the architecture.
Cc: hw.likun@huawei.com
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Use vma_pages function on vma object instead of explicit computation.
Found by coccinelle spatch "api/vma_pages.cocci"
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
As you see in init/version.c, init_uts_ns.name.machine is initially
set to UTS_MACHINE. There is no point to copy the same string.
I dug the git history to figure out why this line is here. My best
guess is like this:
- This line has been around here since the initial support of arm64
by commit 9703d9d7f7 ("arm64: Kernel booting and initialisation").
If ARCH (=arm64) and UTS_MACHINE (=aarch64) do not match,
arch/$(ARCH)/Makefile is supposed to override UTS_MACHINE, but the
initial version of arch/arm64/Makefile missed to do that. Instead,
the boot code copied "aarch64" to init_utsname()->machine.
- Commit 94ed1f2cb5 ("arm64: setup: report ELF_PLATFORM as the
machine for utsname") replaced "aarch64" with ELF_PLATFORM to
make "uname" to reflect the endianness.
- ELF_PLATFORM does not help to provide the UTS machine name to rpm
target, so commit cfa88c7946 ("arm64: Set UTS_MACHINE in the
Makefile") fixed it. The commit simply replaced ELF_PLATFORM with
UTS_MACHINE, but missed the fact the string copy itself is no longer
needed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Fault.c seems to be a magnet for useless and wrong comments, largely
due to its ancestry in other architectures where the code has since
moved on, but the comments have remained intact.
This patch removes both useless and incorrect comments, leaving only
those that say something correct and relevant.
Reported-by: Wenjia Zhou <zhiyuan_zhu@htc.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ILP32 series [1] introduces the dependency on <asm/is_compat.h> for
TASK_SIZE macro. Which in turn requires <asm/thread_info.h>, and
<asm/thread_info.h> include <asm/memory.h>, giving a circular dependency,
because TASK_SIZE is currently located in <asm/memory.h>.
In other architectures, TASK_SIZE is defined in <asm/processor.h>, and
moving TASK_SIZE there fixes the problem.
Discussion: https://patchwork.kernel.org/patch/9929107/
[1] https://github.com/norov/linux/tree/ilp32-next
CC: Will Deacon <will.deacon@arm.com>
CC: Laura Abbott <labbott@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Yury Norov <ynorov@caviumnetworks.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We currently route pte translation faults via do_page_fault, which elides
the address check against TASK_SIZE before invoking the mm fault handling
code. However, this can cause issues with the path walking code in
conjunction with our word-at-a-time implementation because
load_unaligned_zeropad can end up faulting in kernel space if it reads
across a page boundary and runs into a page fault (e.g. by attempting to
read from a guard region).
In the case of such a fault, load_unaligned_zeropad has registered a
fixup to shift the valid data and pad with zeroes, however the abort is
reported as a level 3 translation fault and we dispatch it straight to
do_page_fault, despite it being a kernel address. This results in calling
a sleeping function from atomic context:
BUG: sleeping function called from invalid context at arch/arm64/mm/fault.c:313
in_atomic(): 0, irqs_disabled(): 0, pid: 10290
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[...]
[<ffffff8e016cd0cc>] ___might_sleep+0x134/0x144
[<ffffff8e016cd158>] __might_sleep+0x7c/0x8c
[<ffffff8e016977f0>] do_page_fault+0x140/0x330
[<ffffff8e01681328>] do_mem_abort+0x54/0xb0
Exception stack(0xfffffffb20247a70 to 0xfffffffb20247ba0)
[...]
[<ffffff8e016844fc>] el1_da+0x18/0x78
[<ffffff8e017f399c>] path_parentat+0x44/0x88
[<ffffff8e017f4c9c>] filename_parentat+0x5c/0xd8
[<ffffff8e017f5044>] filename_create+0x4c/0x128
[<ffffff8e017f59e4>] SyS_mkdirat+0x50/0xc8
[<ffffff8e01684e30>] el0_svc_naked+0x24/0x28
Code: 36380080 d5384100 f9400800 9402566d (d4210000)
---[ end trace 2d01889f2bca9b9f ]---
Fix this by dispatching all translation faults to do_translation_faults,
which avoids invoking the page fault logic for faults on kernel addresses.
Cc: <stable@vger.kernel.org>
Reported-by: Ankit Jain <ankijain@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
On kernels built with support for transparent huge pages, different CPUs
can access the PMD concurrently due to e.g. fast GUP or page_vma_mapped_walk
and they must take care to use READ_ONCE to avoid value tearing or caching
of stale values by the compiler. Unfortunately, these functions call into
our pgtable macros, which don't use READ_ONCE, and compiler caching has
been observed to cause the following crash during ext4 writeback:
PC is at check_pte+0x20/0x170
LR is at page_vma_mapped_walk+0x2e0/0x540
[...]
Process doio (pid: 2463, stack limit = 0xffff00000f2e8000)
Call trace:
[<ffff000008233328>] check_pte+0x20/0x170
[<ffff000008233758>] page_vma_mapped_walk+0x2e0/0x540
[<ffff000008234adc>] page_mkclean_one+0xac/0x278
[<ffff000008234d98>] rmap_walk_file+0xf0/0x238
[<ffff000008236e74>] rmap_walk+0x64/0xa0
[<ffff0000082370c8>] page_mkclean+0x90/0xa8
[<ffff0000081f3c64>] clear_page_dirty_for_io+0x84/0x2a8
[<ffff00000832f984>] mpage_submit_page+0x34/0x98
[<ffff00000832fb4c>] mpage_process_page_bufs+0x164/0x170
[<ffff00000832fc8c>] mpage_prepare_extent_to_map+0x134/0x2b8
[<ffff00000833530c>] ext4_writepages+0x484/0xe30
[<ffff0000081f6ab4>] do_writepages+0x44/0xe8
[<ffff0000081e5bd4>] __filemap_fdatawrite_range+0xbc/0x110
[<ffff0000081e5e68>] file_write_and_wait_range+0x48/0xd8
[<ffff000008324310>] ext4_sync_file+0x80/0x4b8
[<ffff0000082bd434>] vfs_fsync_range+0x64/0xc0
[<ffff0000082332b4>] SyS_msync+0x194/0x1e8
This is because page_vma_mapped_walk loads the PMD twice before calling
pte_offset_map: the first time without READ_ONCE (where it gets all zeroes
due to a concurrent pmdp_invalidate) and the second time with READ_ONCE
(where it sees a valid table pointer due to a concurrent pmd_populate).
However, the compiler inlines everything and caches the first value in
a register, which is subsequently used in pte_offset_phys which returns
a junk pointer that is later dereferenced when attempting to access the
relevant pte.
This patch fixes the issue by using READ_ONCE in pte_offset_phys to ensure
that a stale value is not used. Whilst this is a point fix for a known
failure (and simple to backport), a full fix moving all of our page table
accessors over to {READ,WRITE}_ONCE and consistently using READ_ONCE in
page_vma_mapped_walk is in the works for a future kernel release.
Cc: Jon Masters <jcm@redhat.com>
Cc: Timur Tabi <timur@codeaurora.org>
Cc: <stable@vger.kernel.org>
Fixes: f27176cfc3 ("mm: convert page_mkclean_one() to use page_vma_mapped_walk()")
Tested-by: Richard Ruigrok <rruigrok@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The spi controller nodes omit the dma controller/channel references, add
it.
This does not yet enable DMA for SPI transfers, as the spi-sun6i driver
lacks support for DMA, but always uses PIO to the FIFO.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A64 SoC has a DMA controller that supports 8 DMA channels
to and from various peripherals. The last used DRQ port is 27.
Add a device node for it.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PXA3xx NAND driver supports also the NAND controller found on the
Armada 7K/8K SoCs, so enable it.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The NAND controller used in A7K/A8K is present on the CP110 master part.
It is compatible with the pxa3xx_nand driver but requires the use of the
marvell,armada-8k-nand compatible string due to the need to first enable
the NAND controller.
Add properties to the NAND node to fit the bindings constraints of the
pxa3xx_nand driver and enable the NAND controller.
Add the 'marvell,system-controller' property to the cp110 master NAND
node with a reference to the syscon node. This is new compared to other
boards using the pxa3xx_nand driver and it is needed to be bootloader
independent and enable the NAND controller from the NAND controller
driver itself by writing in these syscon registers.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
[miquel.raynal@free-electrons.com: add NAND ready/busy MPP subnode,
change compatible string to fit the needs of the A7k/A8k SoCs and add
the system controller property]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
When the kernel is entered at EL2 on an ARMv8.0 system, we construct
the EL1 pstate and make sure this uses the the EL1 stack pointer
(we perform an exception return to EL1h).
But if the kernel is either entered at EL1 or stays at EL2 (because
we're on a VHE-capable system), we fail to set SPsel, and use whatever
stack selection the higher exception level has choosen for us.
Let's not take any chance, and make sure that SPsel is set to one
before we decide the mode we're going to run in.
Cc: <stable@vger.kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch fix the warning "xxx has a unit name, but no reg property" by
removing "@0" from such node
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This patch remove leading 0 of unit address and so remove
lots of warning when building DT with W=1.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The clk of grf must be enabled before writing grf
register for rk3399.
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
[the grf clock is already part of the binding since march 2017]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable the Renesas R-Car V3M (R8A77970) SoC in the ARM64 defconfig.
Suggested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull address-limit checking fixes from Ingo Molnar:
"This fixes a number of bugs in the address-limit (USER_DS) checks that
got introduced in the merge window, (mostly) affecting the ARM and
ARM64 platforms"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm64/syscalls: Move address limit check in loop
arm/syscalls: Optimize address limit check
Revert "arm/syscalls: Check address limit on user-mode return"
syscalls: Use CHECK_DATA_CORRUPTION for addr_limit_user_check
This patch enables the SFP ports on the Armada 8040 DB as these ports
are now supported by the PPv2 driver (since the PHY is now optional).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch enables the SFP port on the Armada 7040 DB as this port
is now supported by the PPv2 driver (since the PHY is now optional).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds a comphy phandle to the Ethernet port in the 7040-db
device tree. The comphy is used to configure the serdes PHYs used by
these ports.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds comphy phandles to the Ethernet ports in the mcbin
device tree. The comphy is used to configure the serdes PHYs used by
these ports.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add ITS device tree node, which will be used by PCIe controller.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The physical memory map address and CCSR registers map address are
different between LS2088A and other LS2080A series SoCs.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the reset manager includes for Stratix10. Need to use the '#include'
instead of '/include/' to avoid a DTC syntax error.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Cosmetic patch removing an empty line at the end of the NB pinctrl node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Ports interrupts are used by the PPv2 driver when no PHY is connected to
a port. This patch adds a description of these interrupts.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch describes the comphy available in the cp110 master and slave.
This comphy provides serdes lanes used by various controllers such as
the network one.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch extends on both cp110 the system register area length to
include some of the comphy registers as well.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The comphy is an hardware block giving access to common PHYs that can be
used by various other engines (Network, SATA, ...). This is used on
Marvell 7k/8k platforms for now. Enable the corresponding driver.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Marvell 10G PHY is present on mvebu platforms. Enable it as a module
so that the network works on these platforms.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
There is a further gate in between the mipidphy reference clock and the
actual ref-clock input to the dsi host, making the clock hirarchy look like
clk_24m --> Gate11[14] --> clk_mipidphy_ref --> Gate21[0] --> clk_dphy_pll
Fix the clock reference so that the whole clock subtree gets enabled when
the dsi host needs it.
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
[amended commit message]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Extend the container size to 0x2000 to include the gpio controller at
offset 0x1040.
While at it, add start address notation to the gpio node name to match
its 'offset' property.
Fixes: 63dac0f492 ("arm64: dts: marvell: add gpio support for Armada
7K/8K")
Cc: <stable@vger.kernel.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Armada-37xx UART0 registers are 0x200 bytes wide. Right next to them are
the UART1 registers that should not be declared in this node.
Update the example in DT bindings document accordingly.
Signed-off-by: allen yan <yanwei@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
By adding this regulator, a proper reset is done during boot. Without
this, the UHS failed to be detected after a warm reboot when the SD card
remained in the slot, then it fallback to an HS.
Note that the vmcc is supported by the xenon driver only with the
following fix: "mmc: sdhci-xenon: add set_power callback".
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the relevant details in the Armada 7K/8K Device Tree
to properly mux the UART used for the serial console. Since there is
basically only one possible muxing for the UART0 on the AP, the muxing
configuration is described in armada-ap806.dtsi, and selected from the
individual boards (other boards could be using a different UART).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The downstream RTD1195 and apparently RTD1295 trees have a modified 8250
serial driver that acknowledges its interrupts using the second reg area,
which is an irq mux.
Drop these unused second reg entries for the UART nodes.
Fixes: 72a7786c0a ("ARM64: dts: Add Realtek RTD1295 and Zidoo X9S")
Signed-off-by: Andreas Färber <afaerber@suse.de>
We want this driver to detect critical temperatures in time.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The kernel needs to be compiled as a LP64 binary for ARM64, even when
using a compiler that defaults to code-generation for the ILP32 ABI.
Consequently, we need to explicitly pass '-mabi=lp64' (supported on
gcc-4.9 and newer).
Signed-off-by: Andrew Pinski <Andrew.Pinski@caviumnetworks.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Yury Norov <ynorov@caviumnetworks.com>
Reviewed-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Aarch64 instructions must be word aligned. The current 16 byte
alignment is more than enough. Relax it into 4 byte alignment.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
__efi_fpsimd_begin()/__efi_fpsimd_end() are for use when making EFI
calls only, so using them in non-EFI kernels is not allowed.
This patch compiles them out if CONFIG_EFI is not set.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Keiji Hayashibara