Now there are 2 paths for rx vlan frames. When rx-vlan-hw-accel is
enabled, skb is untagged by NIC, vlan_tci is set and the skb gets into
vlan code in __netif_receive_skb - vlan_hwaccel_do_receive.
For non-rx-vlan-hw-accel however, tagged skb goes thru whole
__netif_receive_skb, it's untagged in ptype_base hander and reinjected
This incosistency is fixed by this patch. Vlan untagging happens early in
__netif_receive_skb so the rest of code (ptype_all handlers, rx_handlers)
see the skb like it was untagged by hw.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
v1->v2:
remove "inline" from vlan_core.c functions
Signed-off-by: David S. Miller <davem@davemloft.net>
Note: get_flags was actually broken, because it should return the
flags capped with vlan_features. This is now done implicitly by
limiting netdev->hw_features.
RX checksumming offload control is (and was) broken, as there was no way
before to say whether it's done for tagged packets.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c95b819ad7 (gre: Use needed_headroom)
made gre use needed_headroom instead of hard_header_len
This uncover a bug in vlan code.
We should make sure vlan devices take into account their
real_dev->needed_headroom or we risk a crash in ipgre_header(), because
we dont have enough room to push IP header in skb.
Reported-by: Diddi Oscarsson <diddi@diddi.se>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the new target ddp offload support ndo_fcoe_ddp_target().
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Quoting Ben Hutchings: we presumably won't be defining features that
can only be enabled on 64-bit architectures.
Occurences found by `grep -r` on net/, drivers/net, include/
[ Move features and vlan_features next to each other in
struct netdev, as per Eric Dumazet's suggestion -DaveM ]
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the vlan device is lockless and single queue do not
transfer the real num queues. This is causing a BUG_ON to occur.
kernel BUG at net/8021q/vlan.c:345!
Call Trace:
[<ffffffff813fd6e8>] ? fib_rules_event+0x28/0x1b0
[<ffffffff814ad2b5>] notifier_call_chain+0x55/0x80
[<ffffffff81089156>] raw_notifier_call_chain+0x16/0x20
[<ffffffff813e5af7>] call_netdevice_notifiers+0x37/0x70
[<ffffffff813e6756>] netdev_features_change+0x16/0x20
[<ffffffffa02995be>] ixgbe_fcoe_enable+0xae/0x100 [ixgbe]
[<ffffffffa01da06a>] vlan_dev_fcoe_enable+0x2a/0x30 [8021q]
[<ffffffffa02d08c3>] fcoe_create+0x163/0x630 [fcoe]
[<ffffffff811244d5>] ? mmap_region+0x255/0x5a0
[<ffffffff81080ef0>] param_attr_store+0x50/0x80
[<ffffffff810809b6>] module_attr_store+0x26/0x30
[<ffffffff811b9db2>] sysfs_write_file+0xf2/0x180
[<ffffffff8114fc88>] vfs_write+0xc8/0x190
[<ffffffff81150621>] sys_write+0x51/0x90
[<ffffffff8100c0b2>] system_call_fastpath+0x16/0x1b
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now vlan are lockless, we dont need special ndo_select_queue() logic.
dev_pick_tx() will do the multiqueue stuff on the real device transmit.
Suggested-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan is a stacked device, like tunnels. We should use the lockless
mechanism we are using in tunnels and loopback.
This patch completely removes locking in TX path.
tx stat counters are added into existing percpu stat structure, renamed
from vlan_rx_stats to vlan_pcpu_stats.
Note : this partially reverts commit 2e59af3dcb (vlan: multiqueue vlan
device)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/8021q/vlanproc.c: In function 'vlandev_seq_show':
net/8021q/vlanproc.c:283:20: warning: unused variable 'fmt'
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that VLAN packets are tagged in dev_hard_start_xmit()
at the bottom of the stack we no longer need to tag them
in the 8021Q module (Except in the !VLAN_FLAG_REORDER_HDR
case).
This allows the accel path and non accel paths to be consolidated.
Here the vlan_tci in the skb is always set and we allow the
stack to add the actual tag in dev_hard_start_xmit().
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for the headroom to be smaller then the
hard_header_len for a short period of time after toggling
the vlan offload setting.
This is not a hard error and skb_cow_head is called in
__vlan_put_tag() to resolve this.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toggling the vlan tx|rx hw offloads needs to set the hard_header_len
as well otherwise we end up using LL_RESERVED_SPACE incorrectly.
This results in pskb_expand_head() being used unnecessarily.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(struct net_device)->vlgrp is rcu protected :
add __rcu annotation and proper rcu primitives.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently each driver that is capable of vlan hardware acceleration
must be aware of the vlan groups that are configured and then pass
the stripped tag to a specialized receive function. This is
different from other types of hardware offload in that it places a
significant amount of knowledge in the driver itself rather keeping
it in the networking core.
This makes vlan offloading function more similarly to other forms
of offloading (such as checksum offloading or TSO) by doing the
following:
* On receive, stripped vlans are passed directly to the network
core, without attempting to check for vlan groups or reconstructing
the header if no group
* vlans are made less special by folding the logic into the main
receive routines
* On transmit, the device layer will add the vlan header in software
if the hardware doesn't support it, instead of spreading that logic
out in upper layers, such as bonding.
There are a number of advantages to this:
* Fixes all bugs with drivers incorrectly dropping vlan headers at once.
* Avoids having to disable VLAN acceleration when in promiscuous mode
(good for bridging since it always puts devices in promiscuous mode).
* Keeps VLAN tag separate until given to ultimate consumer, which
avoids needing to do header reconstruction as in tg3 unless absolutely
necessary.
* Consolidates common code in core networking.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A struct net_device always maps to zero or one vlan groups and we
always know the device when we are looking up a group. We currently
do a hash table lookup on the device to find the group but it is
much simpler to just store a pointer.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN_GROUP_ARRAY_LEN is simply the number of possible vlan VIDs.
Since vlan groups will soon be more of an implementation detail
for vlan devices, rename the constant to be descriptive of its
actual purpose.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In various situations, a device provides a packet to our stack and we
drop it before it enters protocol stack :
- softnet backlog full (accounted in /proc/net/softnet_stat)
- bad vlan tag (not accounted)
- unknown/unregistered protocol (not accounted)
We can handle a per-device counter of such dropped frames at core level,
and automatically adds it to the device provided stats (rx_dropped), so
that standard tools can be used (ifconfig, ip link, cat /proc/net/dev)
This is a generalization of commit 8990f468a (net: rx_dropped
accounting), thus reverting it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roger Luethi noticed packets for unknown VLANs getting silently dropped
even in promiscuous mode.
Check for promiscuous mode in __vlan_hwaccel_rx() and vlan_gro_common()
before drops.
As suggested by Patrick, mark such packets to have skb->pkt_type set to
PACKET_OTHERHOST to make sure they are dropped by IP stack.
Reported-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This covers RX if necessary, as well as TX.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under load, netif_rx() can drop incoming packets but administrators dont
have a chance to spot which device needs some tuning (RPS activation for
example)
This patch adds rx_dropped accounting in vlans and tunnels.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
previously, if a vlan master device was moved from one network namespace
to another, all 802.1q and macvlan slaves were deleted.
we can use dev->reg_state to figure out whether dev_change_net_namespace
is happening, since that won't set dev->reg_state NETREG_UNREGISTERING.
so, this changes 8021q and macvlan to ignore NETDEV_UNREGISTER when
reg_state is not NETREG_UNREGISTERING.
Signed-off-by: David Lamparter <equinox@diac24.net>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Daniel Lezcano <daniel.lezcano@free.fr>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
[patch net-next-2.6] vlan: Use vlan_dev_real_dev in vlan_hwaccel_do_receive
Use helper as in other places.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
compare_ether_header() can have a special implementation on 64 bit
arches if CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is defined.
__napi_gro_receive() and vlan_gro_common() can avoid a conditional
branch to perform device match.
On x86_64, __napi_gro_receive() has now 38 instructions instead of 53
As gcc-4.4.3 still choose to not inline it, add inline keyword to this
performance critical function.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan_hwaccel_do_receive() always returns 0, so make it return void.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding a new vlan, if the underlying interface has no carrier,
then the newly added vlan interface should also have no carrier.
At present, this is not true - the newly added vlan is added with
carrier up. Fix by checking state of real device.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Without the 8021q module loaded in the kernel, all 802.1p packets
(VLAN 0 but QoS tagging) are silently discarded (as expected, as
the protocol is not loaded).
- Without this patch in 8021q module, these packets are forwarded to
the module, but they are discarded also if VLAN 0 is not configured,
which should not be the default behaviour, as VLAN 0 is not really
a VLANed packet but a 802.1p packet. Defining VLAN 0 makes it almost
impossible to communicate with mixed 802.1p and non 802.1p devices on
the same network due to arp table issues.
- Changed logic to skip vlan specific code in vlan_skb_recv if VLAN
is 0 and we have not defined a VLAN with ID 0, but we accept the
packet with the encapsulated proto and pass it later to netif_rx.
- In the vlan device event handler, added some logic to add VLAN 0
to HW filter in devices that support it (this prevented any traffic
in VLAN 0 to reach the stack in e1000e with HW filter under 2.6.35,
and probably also with other HW filtered cards, so we fix it here).
- In the vlan unregister logic, prevent the elimination of VLAN 0
in devices with HW filter.
- The default behaviour is to ignore the VLAN 0 tagging and accept
the packet as if it was not tagged, but we can still define a
VLAN 0 if desired (so it is backwards compatible).
Signed-off-by: Pedro Garcia <pedro.netdev@dondevamos.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit be1f3c2c02 "net: Enable 64-bit
net device statistics on 32-bit architectures" I redefined struct
net_device_stats so that it could be used in a union with struct
rtnl_link_stats64, avoiding the need for explicit copying or
conversion between the two. However, this is unsafe because there is
no locking required and no lock consistently held around calls to
dev_get_stats() and use of the statistics structure it returns.
In commit 28172739f0 "net: fix 64 bit
counters on 32 bit arches" Eric Dumazet dealt with that problem by
requiring callers of dev_get_stats() to provide storage for the
result. This means that the net_device::stats64 field and the padding
in struct net_device_stats are now redundant, so remove them.
Update the comment on net_device_ops::ndo_get_stats64 to reflect its
new usage.
Change dev_txq_stats_fold() to use struct rtnl_link_stats64, since
that is what all its callers are really using and it is no longer
going to be compatible with struct net_device_stats.
Eric Dumazet suggested the separate function for the structure
conversion.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we need to shape traffic using low speeds, we need to
disable tso on network interface :
ethtool -K eth0.2240 tso off
It seems vlan interfaces miss the set_tso() ethtool method.
Before enabling TSO, we must check real device supports
TSO for VLAN-tagged packets and enables TSO.
Note that a TSO change on real device propagates TSO setting
on all vlans, even if admin selected a different TSO setting.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a small possibility that a reader gets incorrect values on 32
bit arches. SNMP applications could catch incorrect counters when a
32bit high part is changed by another stats consumer/provider.
One way to solve this is to add a rtnl_link_stats64 param to all
ndo_get_stats64() methods, and also add such a parameter to
dev_get_stats().
Rule is that we are not allowed to use dev->stats64 as a temporary
storage for 64bit stats, but a caller provided area (usually on stack)
Old drivers (only providing get_stats() method) need no changes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use u64_stats_sync infrastructure to implement 64bit rx stats.
(tx stats are addressed later)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use struct rtnl_link_stats64 as the statistics structure.
On 32-bit architectures, insert 32 bits of padding after/before each
field of struct net_device_stats to make its layout compatible with
struct rtnl_link_stats64. Add an anonymous union in net_device; move
stats into the union and add struct rtnl_link_stats64 stats64.
Add net_device_ops::ndo_get_stats64, implementations of which will
return a pointer to struct rtnl_link_stats64. Drivers that implement
this operation must not update the structure asynchronously.
Change dev_get_stats() to call ndo_get_stats64 if available, and to
return a pointer to struct rtnl_link_stats64. Change callers of
dev_get_stats() accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the accelerated receive path for VLAN's will
drop packets if the real device is an inactive slave and
is not one of the special pkts tested for in
skb_bond_should_drop(). This behavior is different then
the non-accelerated path and for pkts over a bonded vlan.
For example,
vlanx -> bond0 -> ethx
will be dropped in the vlan path and not delivered to any
packet handlers at all. However,
bond0 -> vlanx -> ethx
and
bond0 -> ethx
will be delivered to handlers that match the exact dev,
because the VLAN path checks the real_dev which is not a
slave and netif_recv_skb() doesn't drop frames but only
delivers them to exact matches.
This patch adds a sk_buff flag which is used for tagging
skbs that would previously been dropped and allows the
skb to continue to skb_netif_recv(). Here we add
logic to check for the deliver_no_wcard flag and if it
is set only deliver to handlers that match exactly. This
makes both paths above consistent and gives pkt handlers
a way to identify skbs that come from inactive slaves.
Without this patch in some configurations skbs will be
delivered to handlers with exact matches and in others
be dropped out right in the vlan path.
I have tested the following 4 configurations in failover modes
and load balancing modes.
# bond0 -> ethx
# vlanx -> bond0 -> ethx
# bond0 -> vlanx -> ethx
# bond0 -> ethx
|
vlanx -> --
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan device should not copy the slave or master flags from
the real device. It is not in the bond until added nor is it
a master.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also added an explicit break; to avoid
a fallthrough in net/ipv4/tcp_input.c
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan/macvlan start_xmit() can inform caller of congestion with
NET_XMIT_CN return value. This doesnt mean packet was dropped.
Increment normal stat counters instead of tx_dropped.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
+little renaming of unicast functions to be smooth with multicast ones
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Updates real_num_tx_queues in case underlying real device
has changed real_num_tx_queues.
-v2
As per Eric Dumazet<eric.dumazet@gmail.com> comment:-
-- adds BUG_ON to catch case of real_num_tx_queues exceeding num_tx_queues.
-- created this self contained patch to just update real_num_tx_queues.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is required to correctly select vlan tx queue for a driver
supporting multi tx queue with ndo_select_queue implemented since
currently selected vlan tx queue is unaligned to selected queue by
real net_devce ndo_select_queue.
Unaligned vlan tx queue selection causes thrash with higher vlan
tx lock contention for least fcoe traffic and wrong socket tx
queue_mapping for ixgbe having ndo_select_queue implemented.
-v2
As per Eric Dumazet<eric.dumazet@gmail.com> comments, mirrored
vlan net_device_ops to have them with and without vlan_dev_select_queue
and then select according to real dev ndo_select_queue present or not
for a vlan net_device. This is to completely skip vlan_dev_select_queue
calling for real net_device not supporting ndo_select_queue.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing "ifenslave -d bond0 eth0", there is chance to get NULL
dereference in netif_receive_skb(), because dev->master suddenly becomes
NULL after we tested it.
We should use ACCESS_ONCE() to avoid this (or rcu_dereference())
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not desired for underlaying devices to change type. At the time,
there is for example possible to have bond with changed type from
Ethernet to Infiniband as a port of a bridge. This patch fixes this.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __percpu sparse annotations to net.
These annotations are to make sparse consider percpu variables to be
in a different address space and warn if accessed without going
through percpu accessors. This patch doesn't affect normal builds.
The macro and type tricks around snmp stats make things a bit
interesting. DEFINE/DECLARE_SNMP_STAT() macros mark the target field
as __percpu and SNMP_UPD_PO_STATS() macro is updated accordingly. All
snmp_mib_*() users which used to cast the argument to (void **) are
updated to cast it to (void __percpu **).
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
In the vlan and macvlan drivers, the start_xmit function forwards
data to the dev_queue_xmit function for another device, which may
potentially belong to a different namespace.
To make sure that classification stays within a single namespace,
this resets the potentially critical fields.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruno Prémont found commit 9793241fe9
(vlan: Precise RX stats accounting) added a regression for non
hw accelerated vlans.
[ 26.390576] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 26.396369] IP: [<df856b89>] vlan_skb_recv+0x89/0x280 [8021q]
vlan_dev_info() was used with original device, instead of
skb->dev. Also spotted by Américo Wang.
Reported-By: Bruno Prémont <bonbons@linux-vserver.org>
Tested-By: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__net_init/__net_exit are apparently not going away, so use them
to full extent.
In some cases __net_init was removed, because it was called from
__net_exit code.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows a bond device to specify an arp_ip_target as a host that is
not on the same vlan as the base bond device and still use arp
validation. A configuration like this, now works:
BONDING_OPTS="mode=active-backup arp_interval=1000 arp_ip_target=10.0.100.1 arp_validate=3"
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
8: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
inet6 fe80::213:21ff:febe:33e9/64 scope link
valid_lft forever preferred_lft forever
9: bond0.100@bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
inet 10.0.100.2/24 brd 10.0.100.255 scope global bond0.100
inet6 fe80::213:21ff:febe:33e9/64 scope link
valid_lft forever preferred_lft forever
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth1
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
ARP Polling Interval (ms): 1000
ARP IP target/s (n.n.n.n form): 10.0.100.1
Slave Interface: eth1
MII Status: up
Link Failure Count: 1
Permanent HW addr: 00:40:05:30:ff:30
Slave Interface: eth0
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:13:21:be:33:e9
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using dev_hard_header allows us to use LLC with VLANs and potentially
other Ethernet/TokernRing specific encapsulations. It also removes code
duplication between LLC and Ethernet/TokenRing core code.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide common routine for the transition of operational state for a leaf
device during a root device transition.
Signed-off-by: Patrick Mullaney <pmullaney@novell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of the fact that an explicit rtnl_kill_links is
unnecessary (and skipping it improves batching), as network namespace
exit calls dellink on all remaining virtual devices, and
rtnl_link_unregister calls dellink on all outstanding devices in that
network namespace. To do this we need to leave the vlan proc
directories in place until after network device exit time, which is
done by using register_pernet_subsys instead of
register_pernet_device.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of the new pernet automatic storage management,
and stop using compatibility network namespace functions.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the UP/DOWN state of VLANs is synchronized to the state of the
underlying device, meaning all VLANs are set down once the underlying
device is set down. This causes all routes to the VLAN devices to vanish.
Add a flag to specify a "loose binding" mode, in which only the operstate
is transfered, but the VLAN device state is independant.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With multi queue devices, its possible that several cpus call
vlan RX routines simultaneously for the same vlan device.
We update RX stats counter without any locking, so we can
get slightly wrong counters.
One possible fix is to use percpu counters, to get precise
accounting and also get guarantee of no cache line ping pongs
between cpus.
Note: this adds 16 bytes (32 bytes on 64bit arches) of percpu
data per vlan device.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case register_netdevice() returns an error, and a new vlan_group
was allocated and inserted in vlan_group_hash[] we call
vlan_group_free() without deleting group from hash table. Future
lookups can give infinite loops or crashes.
We must delete the vlan_group using RCU safe procedure.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05423b2413 (vlan: allow null VLAN ID to be used)
forgot to update __vlan_hwaccel_rx() & vlan_gro_common()
We need to set VLAN_TAG_PRESENT flag in skb->vlan_tci
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both vlan and macvlan devices usually don't use a qdisc and immediately
queue packets to the underlying device. Propagate transmission state of
the underlying device to the upper layers so they can react on congestion
and/or inform the sending process.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not need to use read_lock(&dev_base_lock), use RCU instead.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no good reason to not support userspace specifying the
network namespace during device creation, and it makes it easier
to create a network device and pass it to a child network namespace
with a well known name.
We have to be careful to ensure that the target network namespace
for the new device exists through the life of the call. To keep
that logic clear I have factored out the network namespace grabbing
logic into rtnl_link_get_net.
In addtion we need to continue to pass the source network namespace
to the rtnl_link_ops.newlink method so that we can find the base
device source network namespace.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
The temporary copy of the VLAN group is not neccessary since the lower device
is already in the process of being unregistered, if it was neccessary the
memset of the global group would introduce a race condition.
With this removed, the changes to the original code are only a few lines, so
remove the new function and move the code back into vlan_device_event().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow drivers to adjust their receive path dynamically
based on whether GRO is being applied successfully.
Currently all in-tree callers ignore the return values of these
functions and do not need to be changed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This clarifies which return and parameter types are GRO result codes
and not RX result codes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the netdev_ops.ndo_fcoe_get_wwn for VLAN device.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use unregister_netdevice_many() to speedup master device unregister.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a list_head parameter to rtnl_link_ops->dellink() methods
allow us to queue devices on a list, in order to dismantle
them all at once.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently use a 16 bit field (vlan_tci) to store VLAN ID/PRIO on a skb.
Null value is used as a special value, meaning vlan tagging not enabled.
This forbids use of null vlan ID.
As pointed by David, some drivers use the 3 high order bits (PRIO)
As VLAN ID is 12 bits, we can use the remaining bit (CFI) as a flag, and
allow null VLAN ID.
In case future code really wants to use VLAN_CFI_MASK, we'll have to use
a bit outside of vlan_tci.
#define VLAN_PRIO_MASK 0xe000 /* Priority Code Point */
#define VLAN_PRIO_SHIFT 13
#define VLAN_CFI_MASK 0x1000 /* Canonical Format Indicator */
#define VLAN_TAG_PRESENT VLAN_CFI_MASK
#define VLAN_VID_MASK 0x0fff /* VLAN Identifier */
Reported-by: Gertjan Hofman <gertjan_hofman@yahoo.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix vlan_get_size to include vlan->flags. Currently, the
size of the vlan flags is not included in the nlmsg size.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its hard to tell if vlans are dropping frames, since
every frame given to vlan_???_start_xmit() functions
is accounted as fully transmitted by lower device.
We can test dev_queue_xmit() return values to
properly account for dropped frames.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan_dev_hard_start_xmit() & vlan_dev_hwaccel_hard_start_xmit()
select txqueue number 0, instead of using index provided by
skb_get_queue_mapping().
This is not correct after commit 2e59af3dcb
[vlan: multiqueue vlan device] because
txq->tx_packets & txq->tx_bytes changes are performed on
a single location, and not the right locking.
Fix is to take the appropriate struct netdev_queue pointer
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan devices are currently not multi-queue capable.
We can do that with a new rtnl_link_ops method,
get_tx_queues(), called from rtnl_create_link()
This new method gets num_tx_queues/real_num_tx_queues
from real device.
register_vlan_device() is also handled.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds implementation of the net_devices_ops.ndo_fcoe_enable/_disable to
the VLAN driver. It checks if the real_dev has support for ndo_fcoe_enable/
ndo_fcoe_disable and if so, passes on to call the associated real_dev.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds fcoe offload related net_device_ops functions vlan_dev_fcoe_ddp_setup
and vlan_dev_fcoe_ddp_done, their implementation simply calls real eth device
net_device_ops for FCoE DDP setup and done operations.
Updates VLAN netdev field value for fcoe_ddp_xid from real eth device netdev.
Above changes are required for fcoe DDP offload working on a VLAN interface.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
String literals are constant, and usually, we can also tag the array
of pointers const too, moving it to the .rodata section.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason for the arbitrary restriction that device must be
up to create a vlan. This patch was added to Vyatta kernel to resolve startup
ordering issues where vlan's are created but real device was disabled.
Note: the vlan already correctly inherits the operstate from real device; so
if vlan is created and real device is marked down, the vlan is marked
down.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the physical MTU changes we want to ensure that all existing
VLAN device MTUs do not exceed the new underlying MTU. This patch
adds that propagation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VLAN 8021q driver needs to call rcu_barrier() when unloading the module,
instead of syncronize_net(). This is needed to make sure that outstanding
call_rcu() callbacks have completed, before the callback function code is
removed on module unload.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).
I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.
The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 13 +--
drivers/net/e1000/e1000_main.c | 24 +++--
drivers/net/ixgbe/ixgbe_common.c | 14 ++--
drivers/net/ixgbe/ixgbe_common.h | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/ixgbe/ixgbe_type.h | 4 +-
drivers/net/macvlan.c | 11 +-
drivers/net/mv643xx_eth.c | 11 +-
drivers/net/niu.c | 7 +-
drivers/net/virtio_net.c | 7 +-
drivers/s390/net/qeth_l2_main.c | 6 +-
drivers/scsi/fcoe/fcoe.c | 16 ++--
include/linux/netdevice.h | 18 ++--
net/8021q/vlan.c | 4 +-
net/8021q/vlan_dev.c | 10 +-
net/core/dev.c | 195 +++++++++++++++++++++++++++-----------
net/dsa/slave.c | 10 +-
net/packet/af_packet.c | 4 +-
18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers are already converted to new net_device_ops API
and nobody uses old API anymore.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One point of contention in high network loads is the dst_release() performed
when a transmited skb is freed. This is because NIC tx completion calls
dev_kree_skb() long after original call to dev_queue_xmit(skb).
CPU cache is cold and the atomic op in dst_release() stalls. On SMP, this is
quite visible if one CPU is 100% handling softirqs for a network device,
since dst_clone() is done by other cpus, involving cache line ping pongs.
It seems right place to release dst is in dev_hard_start_xmit(), for most
devices but ones that are virtual, and some exceptions.
David Miller suggested to define a new device flag, set in alloc_netdev_mq()
(so that most devices set it at init time), and carefuly unset in devices
which dont want a NULL skb->dst in their ndo_start_xmit().
List of devices that must clear this flag is :
- loopback device, because it calls netif_rx() and quoting Patrick :
"ip_route_input() doesn't accept loopback addresses, so loopback packets
already need to have a dst_entry attached."
- appletalk/ipddp.c : needs skb->dst in its xmit function
- And all devices that call again dev_queue_xmit() from their xmit function
(as some classifiers need skb->dst) : bonding, vlan, macvlan, eql, ifb, hdlc_fr
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can update netdev_queue tx_bytes/tx_packets/tx_dropped counters instead
of dev->stats ones, to reduce number of cache lines dirtied in xmit path.
This fixes a performance problem on SMP when many different cpus take
vlan tx path.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the VLAN event handler does not adjust the VLAN
device's carrier state when the real device or the VLAN device is set
administratively up or down.
The following patch adds a transfer of operating state from the
real device to the VLAN device when the real device is administratively
set up or down, and sets the carrier state up or down during init, open
and close of the VLAN device.
This permits observers above the VLAN device that care about the
carrier state (bonding's link monitor, for example) to receive updates
for administrative changes by more closely mimicing the behavior of real
devices.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Check whether the underlying device provides a set of ethtool ops before
checking for individual handlers to avoid NULL pointer dereferences.
Reported-by: Art van Breemen <ard@telegraafnet.nl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that copying a 16-byte area at ~800k times a second
can be really expensive :) This patch redesigns the frags GRO
interface to avoid copying that area twice.
The two disciples of the frags interface have been converted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi:
gro: Normalise skb before bypassing GRO on netpoll VLAN path
When we detect netpoll RX on the GRO VLAN path we bail out and
call the normal VLAN receive handler. However, the packet needs
to be normalised by calling eth_type_trans since that's what the
normal path expects (normally the GRO path does the fixup).
This patch adds the necessary call to vlan_gro_frags.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski pointed out that my previous fix is broken for
VLAN+netpoll as if netpoll is enabled we'd end up in the normal
receive path instead of the VLAN receive path.
This patch fixes it by calling the VLAN receive hook.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As my netpoll fix for net doesn't really work for net-next, we
need this update to move the checks into the right place. As it
stands we may pass freed skbs to netpoll_receive_skb.
This patch also introduces a netpoll_rx_on function to avoid GRO
completely if we're invoked through netpoll. This might seem
paranoid but as netpoll may have an external receive hook it's
better to be safe than sorry. I don't think we need this for
2.6.29 though since there's nothing immediately broken by it.
This patch also moves the GRO_* return values to netdevice.h since
VLAN needs them too (I tried to avoid this originally but alas
this seems to be the easiest way out). This fixes a bug in VLAN
where it continued to use the old return value 2 instead of the
correct GRO_DROP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocols that use packet_type can be __read_mostly section for better
locality. Elminate any unnecessary initializations of NULL.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As analyzed by Patrick McHardy, vlan needs to reset it's
netdev_ops pointer in it's ->init() function but this
leaves the compat method pointers stale.
Add a netdev_resync_ops() and call it from the vlan code.
Any other driver which changes ->netdev_ops after register_netdevice()
will need to call this new function after doing so too.
With help from Patrick McHardy.
Tested-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netpoll entry checks are required to ensure that we don't
receive normal packets when invoked via netpoll. Unfortunately
it only ever worked for the netif_receive_skb/netif_rx entry
points. The VLAN (and subsequently GRO) entry point didn't
have the check and therefore can trigger all sorts of weird
problems.
This patch adds the netpoll check to all entry points.
I'm still uneasy with receiving at all under netpoll (which
apparently is only used by the out-of-tree kdump code). The
reason is it is perfectly legal to receive all data including
headers into highmem if netpoll is off, but if you try to do
that with netpoll on and someone gets a printk in an IRQ handler
you're going to get a nice BUG_ON.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch optimises the Ethernet header comparison to use 2-byte
and 4-byte xors instead of memcmp. In order to facilitate this,
the actual comparison is now carried out by the callers of the
shared dev_gro_receive function.
This has a significant impact when receiving 1500B packets through
10GbE.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately simplicity isn't always the best. The fraginfo
interface turned out to be suboptimal. The problem was quite
obvious. For every packet, we have to copy the headers from
the frags structure into skb->head, even though for 99% of the
packets this part is immediately thrown away after the merge.
LRO didn't have this problem because it directly read the headers
from the frags structure.
This patch attempts to address this by creating an interface
that allows GRO to access the headers in the first frag without
having to copy it. Because all drivers that use frags place the
headers in the first frag this optimisation should be enough.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently VLAN still has a bit of common code handling the aftermath
of GRO that's shared with the common path. This patch moves them
into shared helpers to reduce code duplication.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In previous kernels, any kernel module could get access to the
'real-device' and the VLAN-ID for a particular VLAN. In more recent
kernels, the code was restructured such that this is hard to do
without accessing private .h files for any module that cannot use
GPL-only symbols.
Attached is a patch to once again allow non-GPL modules the ability to
access the real-device and VLAN id for VLANs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the real device has a neigh_setup function, this
neigh_setup function should be used for the vlan device.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds GRO interfaces for hardware-assisted VLAN reception.
With this in place we're now at parity with LRO as far as the
interface is concerned. That is, you can now take any LRO driver
and convert it over to GRO.
As the CB memory clashes with GRO's use of CB, I've removed it
entirely by storing dev in skb->dev. This is OK because VLAN
gets called first thing in netif_receive_skb and skb->dev is
not used in between us calling netif_rx and netif_receive_skb
getting called.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 656299f706
(vlan: convert to net_device_ops) added a net_device_ops
with a NULL ndo_start_xmit field.
This gives a crash in dev_hard_start_xmit()
Fix it using two net_device_ops structures, one for hwaccel vlan,
one for non hwaccel vlan.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert vlan devices and function pointers to net_device_ops.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The changes to deliver hardware accelerated VLAN packets to packet
sockets (commit bc1d0411) caused a warning for non-NAPI drivers.
The __vlan_hwaccel_rx() function is called directly from the drivers
RX function, for non-NAPI drivers that means its still in RX IRQ
context:
[ 27.779463] ------------[ cut here ]------------
[ 27.779509] WARNING: at kernel/softirq.c:136 local_bh_enable+0x37/0x81()
...
[ 27.782520] [<c0264755>] netif_nit_deliver+0x5b/0x75
[ 27.782590] [<c02bba83>] __vlan_hwaccel_rx+0x79/0x162
[ 27.782664] [<f8851c1d>] atl1_intr+0x9a9/0xa7c [atl1]
[ 27.782738] [<c0155b17>] handle_IRQ_event+0x23/0x51
[ 27.782808] [<c015692e>] handle_edge_irq+0xc2/0x102
[ 27.782878] [<c0105fd5>] do_IRQ+0x4d/0x64
Split hardware accelerated VLAN reception into two parts to fix this:
- __vlan_hwaccel_rx just stores the VLAN TCI and performs the VLAN
device lookup, then calls netif_receive_skb()/netif_rx()
- vlan_hwaccel_do_receive(), which is invoked by netif_receive_skb()
in softirq context, performs the real reception and delivery to
packet sockets.
Reported-and-tested-by: Ramon Casellas <ramon.casellas@cttc.es>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables more ethtool information. The speed and settings of the
underlying device are propagated up. This makes services like SNMP that
use ethtool to get speed setting, work when managing a vlan, without adding
silly heurtistics into SNMP daemon.
For the driver info, just use existing driver strings.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan devices are not reading the gso max size of the parent device. As
a result devices that do not support 64K max gso size are currently
failing.
This issue is seen on 2.6.26 kernels as well and the same patch should be
able to be applied without any issues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new address list lock needs to handle the same device layering
issues that the _xmit_lock one does.
This integrates work done by Patrick McHardy.
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_netdev_mq() now allocates an array of netdev_queue
structures for TX, based upon the queue_count argument.
Furthermore, all accesses to the TX queues are now vectored
through the netdev_get_tx_queue() and netdev_for_each_tx_queue()
interfaces. This makes it easy to grep the tree for all
things that want to get to a TX queue of a net device.
Problem spots which are not really multiqueue aware yet, and
only work with one queue, can easily be spotted by grepping
for all netdev_get_tx_queue() calls that pass in a zero index.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove excessive comments and debugging, use NETDEV_TX codes,
remove some empty lines.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some debugging and excessive comments, merge the two
dev_hard_header calls into one.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to query LRO settings of underlying device when VLAN RX
acceleration is used.
Suggested by Ben Hutchings <bhutchings@solarflare.com>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN header stripping is used, packets currently bypass packet
sockets (and other network taps) completely. For locally existing
VLANs, they appear directly on the VLAN device, for unknown VLANs
they are silently dropped.
Add a new function netif_nit_deliver() to deliver incoming packets
to all network interface taps and use it in __vlan_hwaccel_rx() to
make VLAN packets visible on the underlying device.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_set_promiscuity/allmulti might overflow.
Commit: "netdevice: Fix promiscuity and allmulti overflow" in net-next makes
dev_set_promiscuity/allmulti return error number if overflow happened.
Here, we check all positive increment for promiscuity and allmulti
to get error return.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accesses are mostly structured such that when there are multiple TX
queues the code transformations will be a little bit simpler.
Signed-off-by: David S. Miller <davem@davemloft.net>
- vlan_dev_reorder_header() is only called on the receive path after
calling skb_share_check(). This means we can use skb_cow() since
all we need is a writable header.
- vlan_dev_hard_header() includes a work-around for some apparently
broken out of tree MPLS code. The hard_header functions can expect
to always have a headroom of at least there own hard_header_len
available, so the reallocation check is unnecessary.
- __vlan_put_tag() can use skb_cow_head() to avoid the skb_unshare()
copy when the header is writable.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VLAN code contains multiple spots that use tag, id and tci as
identifiers for arguments and variables incorrectly and they actually
contain or are expected to contain something different. Additionally
types are used inconsistently (unsigned short vs u16) and identifiers
are sometimes capitalized.
- consistently use u16 for storing TCI, ID or QoS values
- consistently use vlan_id and vlan_tci for storing the respective values
- remove capitalization
- add kdoc comment to netif_hwaccel_{rx,receive_skb}
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hide struct vlan_dev_info from drivers to prevent them from growing
more creative ways to use it. Provide accessors for the two drivers
that currently use it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is huge and included at least once in every VLAN acceleration
capable driver. Uninline it; to avoid having drivers depend on the VLAN
module, the function is always built in statically when VLAN is enabled.
With all VLAN acceleration capable drivers that build on x86_64 enabled,
this results in:
text data bss dec hex filename
6515227 854044 343968 7713239 75b1d7 vmlinux.inlined
6505637 854044 343968 7703649 758c61 vmlinux.uninlined
----------------------------------------------------------
-9590
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool support for querying the device for offload settings.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use simplified is_vlan_dev function.
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennert Buytenhek points out that the VLAN code incorrectly adjusts
skb->network_header to point in the middle of the VLAN header and
additionally tries to adjust skb->mac_header without checking for
validity.
The network_header should not be touched at all since we're only
adding headers in front of it, mac_header adjustments are not
necessary at all.
Based on patch by Lennert Buytenhek <buytenh@wantstofly.org>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add GVRP support for dynamically registering VLANs with switches.
By default GVRP is disabled because we only support the applicant-only
participant model, which means it should not be enabled on vlans that
are members of a bridge. Since there is currently no way to cleanly
determine that, the user is responsible for enabling it.
The code is pretty small and low impact, its wrapped in a config
option though because it depends on the GARP implementation and
the STP core.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the unregister_netdevice() call for the VLAN device before cleanup
for the lower device. This is needed by GVRP so it can send a leave
message before the applicant on the lower device is cleaned up.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change vlan_dev_set_vlan_flag() to handle multiple flags at once and
rename to vlan_dev_change_flags(). This allows to to use it from the
netlink interface, which in turn allows to handle necessary adjustments
when changing flags centrally.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu points out that the use of seperate feature bits for features
to be propagated to VLAN devices is going to get messy real soon.
Replace the VLAN feature bits by a bitmask of feature flags to be
propagated and restore the old GSO_SHIFT/MASK values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate feature bits from the NETDEV_FEAT_CHANGE notifier. For now
only TSO is propagated for devices that announce their ability to
support TSO in combination with VLAN accel by setting the NETIF_F_VLAN_TSO
flag.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 30688a9 ([VLAN]: Handle vlan devices net namespace changing)
changed the device notifier to special-case notifications for VLAN
devices, effectively disabling state propagation to underlying VLAN
devices. This is needed for layered VLANs though, so restore the
original behaviour.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move rcu-protected lists from list.h into a new header file rculist.h.
This is done because list are a very used primitive structure all over the
kernel and it's currently impossible to include other header files in this
list.h without creating some circular dependencies.
For example, list.h implements rcu-protected list and uses rcu_dereference()
without including rcupdate.h. It actually compiles because users of
rcu_dereference() are macros. Others RCU functions could be used too but
aren't probably because of this.
Therefore this patch creates rculist.h which includes rcupdates without to
many changes/troubles.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Josh Triplett <josh@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Simply replace proc_create and further data assigned with proc_create_data.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When van device is moved to another namespace proc files,
related to this device, should also change one.
Use the netdev REGISTER and UNREGISTER event handlers for this.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one is similar to what I've done for TUN - set the proper
net after device allocation and clean VLANs on net exit (use the
rtnl_kill_links helper finally).
Plus, drop explicit init_net usage and net != &init_net checks.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This includes moving one on the struct vlan_net and
s/vlan_name_type/vn->name_type/ over the code.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is created in a proper net, so make is show info, related
to this particular net.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The proc_vlan_dir and proc_vlan_conf migrate on the struct
vlan_net and their creation uses the struct net.
The devices' entries use the corresponding device's net.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
All proc files will be created in each net, so prepare them for
this change now, not to mess it with real creation patch.
The net != &init_net checks in them are for git-bisect sanity,
but I will drop them soon.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike TUN, it is empty from the very beginning, and will
be eventually populated later.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently vlan group is searched using one key - the ifindex.
We'll have to lookup the vlan_group by two keys - ifindex and
net. Turning the vlan_group lookup key to struct net_device
pointer will make this process easier.
Besides, this will eliminate one more place in the networking,
that assumes that indexes are unique in the kernel.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
These entries are allocated in vlan_dev_set_egress_priority,
but are never released and leaks on vlan device removal.
Drop these in vlan's ->uninit callback - after the device is
brought down and everyone is notified about it is going to
be unregistered.
Found during testing vlan netnsization patchset.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This may lead to situations, when each of two proc entries produce
data for the other's device.
Looks like a BUG, so this patch is for net-2.6. It will not apply to
net-2.6.26 since dev->nd_net access is replaced with dev_net(dev)
one.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently each vlan_groupd contains 8 pointers on arrays with 512
pointers on struct net_device each :) Such a construction "in many
cases ... wastes memory".
My proposal is to allow for some of these arrays pointers be NULL,
meaning that there are no devices in it. When a new device is added
to the vlan_group, the appropriate array is allocated.
The check in vlan_group_get_device's is safe, since the pointer
vg->vlan_devices_arrays[x] can only switch from NULL to not-NULL.
The vlan_group_prealloc_vid() is guarded with rtnl lock and is
also safe.
I've checked (I hope that) all the places, that use these arrays
and found, that the register_vlan_dev is the only place, that can
put a vlan device on an empty vlan_group.
Rough calculations shows, that after the patch a setup with a
single vlan dev (or up to 512 vlans with sequential vids) will
occupy approximately 8 times less memory.
The question I have is - does this patch makes sense, or a totally
new structures are required to store the vlan_devs?
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Changing these flags requires to use dev_set_allmulti/dev_set_promiscuity
or dev_change_flags. Setting it directly causes two unwanted effects:
- the next dev_change_flags call will notice a difference between
dev->gflags and the actual flags, enable promisc/allmulti
mode and incorrectly update dev->gflags
- this keeps the underlying device in promisc/allmulti mode until
the VLAN device is deleted
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce per-net_device inlines: dev_net(), dev_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC_FMT had only one user and we tried to get rid of
that, but this created more problems than it solved.
As a result, this reverts three commits:
235365f3aa ("net/8021q/vlan_dev.c: Use
print_mac."), fea5fa875e ("[NET]: Remove
MAC_FMT"), and 8f789c4844 ("[NET]:
Elminate spurious print_mac() calls.")
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse the existing logic for multicast list synchronization for the
unicast address list. The core of dev_mc_sync/unsync are split out as
__dev_addr_sync/unsync and moved from dev_mcast.c to dev.c. These are
then used to implement dev_unicast_sync/unsync as well.
I'm working on cleaning up Intel's FCoE stack, which generates new MAC
addresses from the fibre channel device id assigned by the fabric as
per the current draft specification in T11. When using such a
protocol in a VLAN environment it would be nice to not always be
forced into promiscuous mode, assuming the underlying Ethernet driver
supports multiple unicast addresses as well.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
I think, that we can make this code flow easier to understand
by introducing the vlan_set_encap_proto() function (I hope the
name is good) to setup the skb proto and merge the paths calling
netif_rx() together.
[Patrick: Modified to apply on top of my previous patches]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- remove three instances of identical code
- remove unnecessary NULL initialization
- remove obvious and unnecessary comments
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checkpatch cleanups, consisting mainly of overly long lines and
missing spaces.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep track of the number of VLAN devices in a vlan group. This allows
to have the caller sense when the group is going to be destroyed and
stop using it, which in turn allows to remove the wrapper around
unregister_vlan_dev for the NETDEV_UNREGISTER notifier and avoid
iterating over all possible VLAN ids whenever a device in unregistered.
Also fix what looks like a use-after-free (but is actually safe since
we're holding the RTNL), the real_dev reference should not be dropped
while we still use it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save two levels of indentation by aborting on error conditions,
remove unnecessary initialization to NULL and remove two obvious
comments.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- move module init/exit functions to end of file, remove some now unnecessary
forward declarations
- remove some obvious comments
- clean up proc init function and move a proc-related printk there
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GET_VLAN_INGRESS_PRIORITY_CMD/GET_VLAN_EGRESS_PRIORITY_CMD ioctls are
not implemented and won't be, new functionality will be added to the netlink
interface. Remove the code and make the ioctl handler return -EOPNOTSUPP
for unknown commands instead of -EINVAL.
Also remove a comment about passing unknown commands to the underlying
device, that doesn't make any sense since its a VLAN specific ioctl and
if its not implemented here, its implemented nowhere.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- use pr_* functions and common prefix for non-device related messages
- remove VLAN_ printk levels
- kill lots of useless debugging statements
- remove a few unnecessary printks like for double VID registration (already
returns -EEXIST) and kill of a number of unnecessary checks in
vlan_proc_{add,rem}_dev() that are already performed by the caller
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan->real_dev is always equal to the device since thats what we used
for the lookup. It doesn't even seem worth a WARN_ON or BUG_ON.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move device setup to vlan_dev.c and make all the VLAN device methods
static.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only user already includes __FUNCTION__ (vlan_proto_init) in the
output, which is enough to identify what the message is about.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow vlans nesting other vlans without lockdep's warnings (max. 2 levels
i.e. parent + child). Thanks to Patrick McHardy for pointing a bug in the
first version of this patch.
Reported-by: Benny Amorsen
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan module cleanup function starts with
vlan_netlink_fini();
vlan_ioctl_set(NULL);
The first call removes all the vlan devices and
the second one closes the vlan ioctl.
AFAIS there's a tiny race window between these two
calls - after rtnl unregistered all the vlans, but
the ioctl handler isn't set to NULL yet, user can
manage to call this ioctl and create one vlan device,
and that this function will later BUG_ON seeing
non-emply hashes.
I think, that we must first close the vlan ioctl
and only after this remove all the vlans with the
vlan_netlink_fini() call.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SET_VLAN_NAME_TYPE_CMD command w/o CAP_NET_ADMIN capability
doesn't release the rtnl lock.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix misbehavior of vlan_dev_hard_start_xmit() for recursive encapsulations.
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
While the VLAN device is down, the unicast addresses are not configured
on the underlying device, so we shouldn't attempt to sync them.
Noticed by Dmitry Butskoy <buc@odusz.so-cdu.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on report and patch by Doug Kehn <rdkehn@yahoo.com>:
vconfig returns the following error when attempting to execute the
set_ingress_map command:
vconfig: socket or ioctl error for set_ingress_map: Operation not permitted
In vlan.c, vlan_ioctl_handler for SET_VLAN_INGRESS_PRIORITY_CMD
sets err = -EPERM and calls vlan_dev_set_ingress_priority.
vlan_dev_set_ingress_priority is a void function so err remains
at -EPERM and results in the vconfig error (even though the ingress
map was set).
Fix by setting err = 0 after the vlan_dev_set_ingress_priority call.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A net_device struct provides field dev_id. It is used for
unique ipv6 generation in case of shared network cards
(as for the OSA network cards of IBM System z).
If VLAN devices are built on top of such shared network cards,
this dev_id information needs to be transferred to the VLAN device.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hardware header operations are part of the protocol class
not the device instance, make them into a separate object and
save memory.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add inline for common usage of hardware header creation, and
fix bug in IPV6 mcast where the assumption about negative return is
an errno. Negative return from hard_header means not enough space
was available,(ie -N bytes).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes most of the generic device layer network
namespace safe. This patch makes dev_base_head a
network namespace variable, and then it picks up
a few associated variables. The functions:
dev_getbyhwaddr
dev_getfirsthwbytype
dev_get_by_flags
dev_get_by_name
__dev_get_by_name
dev_get_by_index
__dev_get_by_index
dev_ioctl
dev_ethtool
dev_load
wireless_process_ioctl
were modified to take a network namespace argument, and
deal with it.
vlan_ioctl_set and brioctl_set were modified so their
hooks will receive a network namespace argument.
So basically anthing in the core of the network stack that was
affected to by the change of dev_base was modified to handle
multiple network namespaces. The rest of the network stack was
simply modified to explicitly use &init_net the initial network
namespace. This can be fixed when those components of the network
stack are modified to handle multiple network namespaces.
For now the ifindex generator is left global.
Fundametally ifindex numbers are per namespace, or else
we will have corner case problems with migration when
we get that far.
At the same time there are assumptions in the network stack
that the ifindex of a network device won't change. Making
the ifindex number global seems a good compromise until
the network stack can cope with ifindex changes when
you change namespaces, and the like.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every user of the network device notifiers is either a protocol
stack or a pseudo device. If a protocol stack that does not have
support for multiple network namespaces receives an event for a
device that is not in the initial network namespace it quite possibly
can get confused and do the wrong thing.
To avoid problems until all of the protocol stacks are converted
this patch modifies all netdev event handlers to ignore events on
devices that are not in the initial network namespace.
As the rest of the code is made network namespace aware these
checks can be removed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies every packet receive function
registered with dev_add_pack() to drop packets if they
are not from the initial network namespace.
This should ensure that the various network stacks do
not receive packets in a anything but the initial network
namespace until the code has been converted and is ready
for them.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko